Semelab Plc LM317AHVK, LM317HVK, LM117K-BSS2, LM117K, LM117IG Datasheet

IP117, IP117A

IP317, IP317A

LM117, LM117A

							1.5 AMP
							POSITIVE ADJUSTABLE
1	2	3		1	2	3	VOLTAGE REGULATOR
							FOR HI-REL APPLICATIONS

Pin 1 – ADJ.		Pin 1 – ADJ.
Pin 2	– VOUT	Pin 2	– VOUT
Pin 3	– VIN	Pin 3	– VIN
Case – VOUT		Case – Isolated
G Package – TO257		IG Package – TO257
	!		!

Pin 1	– ADJ.	Pin 1	– ADJ.
Pin 2	– VOUT	Pin 2	– VOUT
Pin 3	– VIN	Pin 3	– VIN

SMD1	SMD05
CERAMIC SURFACE	CERAMIC SURFACE
MOUNT	MOUNT

		1	2
1	2
			3
	3
Pin 1	– ADJ.	Pin 1	– ADJ.
Pin 2	– VIN	Pin 2	– VIN
Case – VOUT		Case – VOUT
K Package – TO3		R Package – TO66

FEATURES

•Output voltage range of:

1.25to 40V for standard version

1.25to 60V for HV version

•Output voltage tolerance 1%

•Load regulation 0.3%

•Line regulation 0.01%/V

•Complete series of protections: current limiting

thermal shutdown soa control

•Also available in TO220 metal isolated package (1mm pins)

1 2 3

Pin 1 – ADJ.

Pin 2 – VOUT

Pin 3 – VIN

T Package – TO220 Plastic

ABSOLUTE MAXIMUM RATINGS (Tcase = 25°C unless otherwise stated)

VI–O	Input - Output Differential Voltage	– Standard	40V
		– HV Series	60V
IO	Output Current		Internally limited
PD	Power Dissipation		Internally limited
TJ	Operating Junction Temperature Range		See Table Above
TSTG	Storage Temperature		–65 to 150°C
Semelab plc. Telephone [phone].		Fax [phone].	Prelim. 8/00
	E-mail: [e-mail]	Website: http://www.semelab.co.uk

IP117, IP117A

IP317, IP317A

LM117, LM117A

								IP117A , IP117AHV			IP117 , IP117HV
								LM117A , LM117AHV			LM117 , LM117HV
	Parameter		Test Conditions					Min.	Typ.	Max.	Min.	Typ.	Max.	Units
			IOUT = 10mA					1.238	1.25	1.262				V
VREF		Reference Voltage	IOUT = 10mA to IMAX
			VIN – VOUT = 3V to VMAX					1.225	1.250	1.270	1.200	1.250	1.300	V
			P £ PMAX		TJ = –55 to +150°C
	DVOUT	Line Regulation 1	VIN – VOUT = 3V to VMAX						0.005	0.010		0.010	0.020	% / V
	DVIN				TJ = –55 to +150°C				0.010	0.020		0.020	0.050
			IOUT = 10mA to IMAX				VOUT £ 5V		5	15		5	15	mV
	DVOUT	Load Regulation 1					VOUT ³ 5V		0.1	0.3		0.1	0.3	%
DIOUT			IOUT = 10mA to IMAX				VOUT £ 5V		15	50		20	50	mV
			TJ = –55 to +150°C				VOUT ³ 5V		0.3	1		0.3	1	%
		Thermal Regulation	tp = 20ms						0.002	0.020		0.030	0.070	%/W
			VOUT = 10V				CADJ = 0		65			65		dB
		Ripple Rejection				CADJ = 10mF
			f = 120Hz					66	80		66	80		dB
					TJ = –55 to +150°C
IADJ		Adjust Pin Current	TJ = –55 to +150°C						50	100		50	100	mA
DIADJ		Adjust Pin Current	IOUT = 10mA to IMAX
			TJ = –55 to +150°C						0.2	5		0.2	5	mA
		Change
			VIN – VOUT = 2.5V to VMAX
			VIN – VOUT = 40V						3.5	5		3.5	5
IMIN		Minimum Load	TJ = –55 to +150°C
														mA
		Current	VIN – VOUT = 60V (HV SERIES)						3.5	7		3.5	7
			TJ = –55 to +150°C
			VIN – VOUT £ 15V					1.5	2.2		1.5	2.2		A
			TJ = –55 to +150°C
ICL		Current Limit
			VIN – VOUT = 40V					0.30	0.50		0.30	0.50		A
			VIN – VOUT = 60V (HV SERIES)						0.10			0.10
DVOUT Temperature			TJ = –55 to +150°C						1	2		1		%
DTEMP Stability
DVOUT		Long Term Stability	TA = +125°C			t = 1000 Hrs			0.3	1		0.3	1	%
DTIME
en		RMS Output Noise	f = 10 Hz to 10 kHz						0.001			0.001		%
		(% of VOUT)
RqJC		Thermal Resistance	K Package						2.3	3		2.3	3
			R Package						5	7		5	7	°C/W
		Junction to Case
			G, IG Packages						3	5		3	5

1)Regulation is measured at constant junction temperature, using pulse testing at a low duty cycle. Changes in output voltage due to heating effects are covered under thermal regulation specifications. Load regulation is measured from the bottom of the package for the TO–3 and TO–66 packages, at the junction of the wide and narrow portion of the output lead for the TO–220 package, and 1/8” below the base of the package on the output pin of the TO–257 package.

2) Test Conditions unless othewise stated:

VIN – VOUT = 5V , TJ = 25°C , IOUT = 0.5A , IMAX = 1.5A. PMAX = 10W for SMD1, 20W for all other package styles. VMAX = 40V for standard series , 60V for HV series.

Semelab plc. Telephone [phone].	Fax [phone].	Prelim. 8/00
E-mail: [e-mail]	Website: http://www.semelab.co.uk