Sega

Sega Barcode Reader 999-0988, Barcode Reader Star Wars Racer Arcade User Manual

Loading...

1st Printing July 2000

MINI DX

OWNER’S MANUAL

PART NO. 999-0988

Warranty

Your new Sega Product is covered for a period of 90 days from the date of shipment. This certifies that the Printed Circuit Boards, Power Supplies and Monitor are to be free of defects in workmanship or materials under normal operating conditions. This also certifies that all Interactive Control Assemblies are to be free from defects in workmanship and materials under normal operating conditions. No other product in this machine is hereby covered.

Sellers sole liability in the event a warranted part described above fails shall be, at its option, to replace or repair the defective part during the warranty period. For Warranty claims, contact your Sega Distributor.

Should the Seller determine, by inspection that the product was caused by Accident, Misuse, Neglect, Alteration, Improper Repair, Installation or Testing, the warranty offered will be null and void.

Under no circumstances is the Seller responsible for any loss of profits, loss of use, or other damages.

This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other warranties expressed or implied. Under no circumstance shall it extend beyond the period of time listed above.

TABLE OF CONTENTS

1-2

INTRODUCTION OF THE OWNER MANUAL

3

GENERAL PRECAUTIONS

4-5

1. Precautions to be Heeded for Operation

6-7

2. Name of Parts

8

3. Accessories

9-10

4. Assembly and Installation

11-16

A) Assembly of Cabinet

11

B) Securing in Place (Adjuster Adjustment)

12

C) Power Supply

13

D) Assembling Check

14-16

1) Memory Test

 

2) C.R.T. Test

 

3) Sound Test

 

4) Input Test

 

5) Output Test

 

5. Precautions to be Heeded When Moving the Machine

17

6. Contents of Game

18

7. How to Play

19-25

A) Select Screen

19-20

B) Courses and Vehicles

21

C) How to Operate

21-22

D) Game Screen

23

E) Game Over

23

F) Damage System

23

G) Name Entry

24

H) Continuous Play vs. Play

24

I) Password

25

J) Flow Chart

25

8. System Test Mode

26-41

8-1 Switch Unit and Coin Meter

27

8-2 System Test Mode

28-41

A) System Test Mode Menu

28

B) Ram Test

28

C) JVS Test

29

D) Sound Test

30

E) C.R.T. Test

30

F) System Assignments

31-32

G) Coin Assignments

33-37

H) Bookkeeping

38

I) Backup Ram Clear

39

J) Rombd Test

40

K) Clock Setting

41

L) Game Test Mode

41

1

9. Game Test Mode

42-49

A) Game Menu

42

B) Input Test

43

C) Output Test

44

D) Game Assignments

45-46

E) Bookkeeping

47

F) Calibration Test

48

G) Backup Data Clear

49

H) Features

49

10. Control Panel

50-54

10-1 Removing the Control Panel

51

10-2 Volume Adjustment\Replacement

52-53

10-3 Greasing

54

11. Coin Selector

55-58

12. Monitor

59-61

12-1 Cautions and Warnings Concerning the Safety for Handling

 

the Monitors

59

12-2 Cautions to be Heeded When Cleaning the C.R.T. Surfaces

60

12-3 Adjustment Method

61

13. Replacing the Flourescent Lamps and Buttons

62

14. Periodic Inspection Table

63

15. Design Related Parts

64

Design Related Parts

64

16.Parts List

65-72

Switch Unit

65

Assembly AC Unit

66

Assembly Seat

67

Assembly Controller

68-69

Assembly Lever Mecha

70-71

Assembly Brake

72

17. Wire Color Table

73-74

Wiring Diagram

74

2

 

SPECIFICATIONS

Installation space:

. 34 in.(L) x 87 in.(W)

Height:

. 76 in.

Weight:

Approx. 500 lbs.

Power maximum current:

6.8 Amp AC 120V 60 Hz

MONITOR:

33” COLOR MONITOR

INTRODUCTION OF THE OWNERS MANUAL

SEGA ENTERPRISES, LTD., has for more than 30 years been supplying various innovative and popular amusement products to the world market. This Owners Manual is intended to provide detailed descriptions together with all the necessary installation, game settings and parts ordering information related to the STAR WARS RACER ARCADE, a new SEGA product.

This manual is intended for those who have knowledge of electricity and technical expertise, especially in ICs, CRTs, microprocessors, and circuit boards. Read this manual carefully to acquire sufficient knowledge before working on the machine. Should there be a malfunction, nontechnical personnel should under no circumstances touch the interior system. Should the need arise, contact our main office, or the closest branch office listed below.

SEGA ENTERPRISES, INC. (USA) Customer Service

45133 Industrial Drive Fremont, CA 94538 Phone 415-701-6580 Fax 415-701-6594

7:30 am - 4:00 pm, Pacific Standard Time Monday thru Friday

3

General Precautions

Follow Instructions: All operating and use instructions should be followed.

Attachments: Do not use attachments not recommended by the product manufacturer as they may cause hazards.

Accessories: Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use only mounting accessories recommended by the manufacturer.

Moving the Product: This product should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product to overturn.

Ventilation: Slots and openings in the cabinet are provided for ventilation, to ensure reliable operation of the product and to protect it from overheating; these openings must not be blocked or covered. The openings should never be blocked by placing the product in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

Power Sources: This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your location, consult your local power company. For products intended to operate from battery power or other sources, refer to the operating instructions.

Grounding or Polarization: This product is equipped with a three-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.

Power Cord Protection: Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

Overloading: Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

Object and Liquid Entry: Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

Servicing: Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

Damage Requiring Service: Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a)If the power cord or plug is damaged;

b)If liquid has been spilled, or objects have fallen into the product;

c)If the product has been exposed to rain or water;

d)If the product does not operate normally when following the operating instructions. Adjust only those controls that are explained in the operating instructions. An improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation;

e)If the product has been dropped or damaged in any way;

f)When the product exhibits a distinct change in performance; this indicates a need for service.

Replacement Parts: When replacement parts are required, be sure the service technician has used replacements parts specified by the manufacturer or that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

4

Safety Check: Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

Heat: The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

Lithium Battery- Dispose of batteries only in accordance with the battery manufacturer’s recommendations. Do not dispose in an open flame condition, since the battery may explode.

Cleaning: When cleaning the monitor glass, use water or glass cleaner and a soft cloth. Do not apply chemicals such as benzine, thinner, etc.

Location: This an indoor game machine, DO NOT install it outside. To ensure proper usage, avoid installing indoors in the places mentioned below:

Places subject to rain/water leakage, or condensation due to humidity;

In close proximity to a potential wet area;

Locations receiving direct sunlight;

Places close to heating units or hot air;

In the vicinity of highly inflammable/volatile chemicals or hazardous matter;

On sloped surfaces;

In the vicinity of emergency response facilities such as fire exits and fire extinguishers;

Places subject to any type of violent impact;

Dusty places.

INSTALLATION PRECAUTIONS

Verify the amperage of the branch circuit outlet before plugging in the power plug. Do not overload the circuit.

Avoid using an extension cord. If one is required, use an extension cord of type SJT, 16/3 AWG rated min. 120 VAC, 7A.

Moving this unit requires a minimum clearance (of doors, etc.) of 32” (W) by 77” (H).

For the operation of this machine, secure a minimum area of 32” (W) by 42”(D).

REGULATORY APPROVALS

This game has been tested and found to comply with the Federal Communications Commission Rules.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This game has been tested and listed by Underwriters Laboratories, Inc., to ANSI/UL22.

5

1 . PRECAUTIONS TO BE HEEDED FOR OPERATION

In order to prevent accidents, be sure to comply with the following points before and during operation.

PRECAUTIONS TO BE HEEDED FOR OPERATION BEFORE STARTING THE OPERATION

In order to avoid accidents, check the following before starting the operation: Check if all of the adjusters are in contact with the surface. If they are not,

the cabinet can move and cause an accident.

Do not climb on the product. Climbing on the product can cause falling down accidents. To check the top portion of the product, use a step.

To avoid electric shock, check to see if door & cover parts are 508.5

To avoid electric shock, short circuit and or parts damage, do not put the following items on or in the periphery of the product:

Flower vases, flower pots, cups, water tanks, cosmetics, and receptacles/ containers/vessels containing chemicals and water.

To avoid injury, be sure to provide sufficient space by considering the potentially crowded situation at the installation location. Insufficient installation space can cause the player to come into contact with or hit others and result in injury or trouble.

6

PRECAUTIONS TO BE HEEDED DURING OPERATION

To avoid injury and accidents, those who fall under the following categories are not allowed to play the game:

*Intoxicated persons

*Those who have high blood pressure or heart problems.

*Those who have experienced muscle convulsion or loss of consciousness when playing video games, etc.

*Persons susceptible to motion sickness.

*Persons whose acts runs counter to the products warning displays.

*Instruct those who wear high-heeled shoes to refrain from

playing the game by explaining that playing the game with highheeled shoes is very dangerous and likely to cause a

potentially hazardous situation.

To avoid electric shock and short circuit, do not allow customers to put hands and fingers or extraneous matter in openings of the product or small openings in or around doors.

To avoid electric shock circuit, do not allow the customers to unplug the power plug without a justifiable reason.

Although this product has the accident preventive covering attached to potentially hazardous places where hand and fingers could be caught, small children are unable to perceive hazards. Use care so that small children do not come close to the product when in play.

Immediately stop such violent acts as hitting and kicking the product. Such violent acts can cause parts damage and /or falling down, resulting in injury due to fragments and falling down.

7

2. NAME OF PARTS

GAME SPECIFICATIONS

WIDTH

LENGTH

HEIGHT

WEIGHT

 

 

 

DURING SHIPPING

Shipping dimensions currently unavailable

 

 

 

 

 

 

 

 

 

 

 

CABINET

 

 

 

 

 

 

 

 

 

SEAT CABI

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WHEN ASSEMBLED

34” X

87” X

76”

500 LBS

8

3. ACCESSORIES

 

 

 

 

 

 

KEY

 

 

 

DESCRIPTION

OWNERS MANUAL

KEY MASTER

 

 

 

Part No. (Qty.)

999-0921

 

220-5576 (2)

(2)

 

 

 

Note

 

 

For opening/closing

For the CASHBOX DOOR

 

 

 

 

 

 

the doors

 

 

 

 

Figures

 

 

 

 

 

 

 

If Part No. has no description, the Number has not

 

 

 

 

 

been registered or can not be registered. Such a

 

 

 

 

 

part may not be obtainable even if the customer

 

 

 

 

 

desires to purchase it. Therefore, ensure that the

 

 

 

 

 

part is in safekeeping with you.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TAMPERPROOF WRENCH

 

 

 

 

 

 

M8 540-0009-01 (1)

 

 

 

 

 

 

TOOL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9

THE SHIPMENT METHOD DESCRIBED BELOW ONLY APPLIES TO ‘HIKARU’ BOARDS CONTAINED IN THE FOLLOWING GAMES:

LOST WORLD, VIRTUA FIGHTER 3, SUPER GT, SEGA BASS FISHING, STRIKER 2

HARLEY DAVIDSON, STAR WARS RACER

!!NEVER SHIP HIKARU GAME BOARDS

OUTSIDE OF CAGE!!

CARTON BOX 601-8928 (1)

Used for transporting the GAME BOARD. {SUPPLIED WITH YOUR GAME}

DO NOT SHIP GAME BOARD WITHOUT

THIS BOX AS IT MAY DAMAGE THE GAME

BOARD AND VOID YOUR WARRANTY.

“CHECK SIDE” Display

FILTER BOARD

NO OTHER GAMES BOARDS ARE TO BE SHIPPED IN THE CAGE AS THEY MAY BE DAMAGED BEYOND REPAIR. PLEASE SHIP THEM WITHOUT CAGE PROPERLY PROTECTED DURING SHIPPING.

10

4 . ASSEMBLING AND INSTALLATION

Assembling should be performed as per this manual. Since this is a complex machine, erroneous assembling may cause damage to the machine, or malfunctioning to occur.

When assembling, be sure to perform work by plural persons. Depending on the type of work, there are some cases in which a single person performing the work can cause personal injury or parts damage.

When carrying out the assembly work, follow the procedure in the following 4-item sequence:

1

2

3

4

ASSY OF CABINET

SECURING IN PLACE (ADJUSTER ADJUSTMENT)

POWER SUPPLY

ASSEMBLING CHECK

Note that tools such as a phillips-head screwdriver and wrench for M16 hexagon bolt w/24 mm width across flats are required for the assembly work.

A ASSY OF CABINET

Permanantly tightening the hex bolts should not be completed until the leg levelers are adjusted properly.

11

B SECURING IN PLACE (ADJUSTER ADJUSTMENT)

Be sure to have all the Adjusters make contact with a flat surface. Unless the Adjusters come into contact with a flat surface, the Cabinet can move of itself, causing an accident.

This machine has 4 casters and 4 adjusters (shown below). When the installation position is determined, make sure that the machine position is level, bring the adjusters into direct contact with the floor, and make adjustments so that the casters will be raised approximately 5mm. from the floor.

1Move the machine to the installation position. Be sure to provide adequate space allowing the player to get on and off.

2Have all of the leg adjusters make contact with the floor. Adjust the height of the leg adjusters by using a wrench so that the machine’s position is kept level.

3After making adjustments, fasten the leg adjuster nut upward and secure the height of the leg adjuster.

12

C POWER SUPPLY

Ensure that the power cord is not exposed on the surface (passage, etc.). If exposed, they can be caught and are susceptible to damage. If damaged, the cord can cause an electric shock or short circuit.

Ensure that the writing position is not in the customer’s passage way or the wiring has protective covering.

Connet the game to the power supply and turn on power to the game. Before connecting power supply be sure that power switch if off.

1Turning the AC unit’s main switch on will cause the machine to start the power check and network check automatically.

2In the Power On check, the steering wheel turns left and right, and then returns to the centering position and stops. In this check, the values of the VR inside the control panel are corrected.

3Until this check is finished, and the steering wheel stops do not touch the steering wheel or play the game.

If you do, the steering reaction during the game (reaction at the time of course-out or crash) can not be obtained correctly. In the case of an abnormal reaction during the game, turn power on again from the beginning and complete the power on check.

MAIN SW

To the Power Supply Socket outlet

13

D ASSEMBLING CHECK

In the TEST MODE, ascertain that the assembly has been made correctly and IC BD, is

satisfactory (refer to Section 9).

In the test mode, perform the following test:

(1) MEMORY TEST

 

 

RAM TEST

 

IC15

IC16

IC17S

IC18S

GOOD

IC22

IC23

IC24S

IC25S

GOOD

IC28

IC29S

 

 

GOOD

IC41

 

 

 

GOOD

IC42

 

 

 

GOOD

IC44

IC45S

IC46

IC47S

GOOD

IC91S

IC92S

 

 

GOOD

IC98

 

 

 

GOOD

OPTIONAL SOUND BOARD:

 

IC12

 

 

 

GOOD

OPTIONAL COMMUNICATION BOARD: IC7 IC8 IC9 IC10 GOOD

.

.

.

PRESS TEST BUTTON TO EXIT

(2) C.R.T. TEST

Selecting the RAM TEST on the system test mode menu screen causes the on-board memory to be tested automatically. The game board is satisfactory if the display beside each IC No. shows GOOD.

0

C.R.T. TEST PAGE#1

31

 

RED

GREEN

BLUE

WHITE

PRESS SERVICE BUTTON TO ANOTHER PAGE

PRESS TEST BUTTON TO EXIT

In the system test mode menu, selecting C.R.T. TEST allows the screen (on which the monitor is tested) to be displayed.

C.R.T. TEST PAGE#2

PRESS SERVICE BUTTON TO ANOTHER PAGE

PRESS TEST BUTTON TO EXIT

14

(3) SOUND TEST

SOUND TEST

MAIN SPEAKER LEFT MAIN SPEAKER RIGHT OPTION SPEAKER LEFT OPTION SPEAKER RIGHT

>EXIT

SELECT WITH SERVICE BUTTON

AND

PRESS TEST BUTTON

(4) INPUT TEST

INPUT TEST

 

BOOST

OFF

BRAKE

OFF

LEFT BUTTON

OFF

RIGHT BUTTON

OFF

LEFT LEVER

3E

RIGHT LEVER

3D

START

OFF

SERVICE

OFF

TEST

OFF

PRESS TEST AND SERVICE BUTTON TO EXIT

JVS TEST

>DISPLAY CONFIG EXIT

NODE 1/1 SWITCH

SYSTEM -------------

PLAYER1 ----------------------------

PLAYER2 ----------------------------

COIN

SLOT1 0000 SLOT2 8000 ANALOG

CH1 6300 CH2 5A00 CH3 7D00 CH4 8100 CH5 1F00 CH6 1D00 CH7 1F00 CH8 2000

SELECT WITH SERVICE BUTTON

AND

PRESS TEST BUTTON

In the system test mode, selecting SOUND TEST causes the screen (on which sound related BD and wiring connections are tested) to be displayed.

Check if the sound is satisfactorily emitted from each speaker and the sound volume is appropriate.

Selecting the INPUT TEST on the game test mode menu screen causes the screen (on which each switch is tested) to be displayed. Press each switch. For the coin switch test, insert a coin from the coin inlet with the coin chute door open. If the display beside each switch indicates “ON,” the switch and wiring connections are satisfactory.

15

(5) OUTPUT TEST

OUTPUT TEST

START LAMP

OFF

BOOST LAMP

OFF

BOOST LOCK

OFF

>EXIT

 

SELECT WITH SERVICE BUTTON

AND

PRESS TEST BUTTON

Select OUTPUT TEST from the Menu screen in the Game Test Mode to cause the screen (on which output unit such as lamps and wiring connections are tested) to appear. Ensure that the output unit functions satisfactorily.

Perform the above imspections also at the time of monthly inspection.

16

5 . PRECAUTIONS TO BE HEEDED WHEN MOVING THE MACHINE

When moving the machine, be sure to unplug the power plug. Moving the machine with the plug as is inserted can damage the power cord and cause fire and electric shock hazards.

When moving the machine on the floor, retract the Adjusters and ensure that Casters make contact with the floor. During transportation, pay careful attention so that Casters do not tread power cords. Damaging the power cords can cause an electric shock and/or short circuit.

When lifting the cabinet, be sure to hold the catch portions or bottom part. Lifting the cabinet by holding other portions can damage parts and installation portions, due to the empty weight of the cabinet, and cause personal injury.

Do not insert the fork to places other than designated when using a Forklift to transport the machine.

Failure to observe this could cause falling down and injury resulting from falling down.

Do not push the plastic made parts. Failure to observe this may damage parts and cause injury due to fragments resulting from damage.

When transporting the product in places with steps, disassemble into each unit before transporting. Inclining the product in an as is assembled condition or placing the cabinet in places with steps can damage the unit’s joining portions.

To protect surface, do not directly apply a rope to the surfaces of product. Use protective materials to the places the rope is applied to.

17

6. CONTENTS OF GAME

The following explanations apply in the event the product is functioning satisfactorily. Should there be any moves different from the following contents, some sort of fault may have occurred. Immediately look into the cause of the fault and eliminate it to ensure satisfactory operation.

When the product is energized, the Billboard’s fluorescent lamp is always lit. During the advertise mode, the advertise screen is shown on the monitor and sound is emitted from the speakers in the front, left and right of the seat. Setting to No Sound Output during the advertise is possible in the TEST mode. During the advertise mode, the button on the Control Panel is unlit.

18

7. HOW TO PLAY

To adjust the seat position, pull the lever under the seat on the right-hand side to release the seat lock, and slide the seat forward or backward to the desired position.

The game starts upon inserting the required number of coins for one play.

(A) SELECT

SCREEN

For Communication Play:

When in communication play, the monitor screen remains stationary for approximately 10 seconds to wait for the participant. The time limit is displayed in the upper right corner of the screen. Press the START button to cancel vs. play and proceed to the 1P mode. To avoid misoperation, pressing the START button will not cancel vs. mode during the first 3 seconds.

Use the SELECT button to choose one of the 4 courses and press the START button to decide. The time limit for selecting the course is displayed in the upper right corner of the screen. The course displayed on the left is easier, and the difficulty increases upon proceeding to the right.

19

Use the SELECT button to choose one of the 4 vehicles and press the START button to decide. The time limit for selecting the vehicle is displayed in the upper right corner of the screen. At the time of shipment, only 2 of the vehicles are usable. However, by fulfilling the requirements described later in this manual, the remaining 2 vehicles will become available. The performance of each vehicle differs.

For Communication Play:

After selecting your vehicle, input your “name” using 3 letters. This name is displayed at the top of the opponent’s vehicle in the game screen. Use the SELECT button to scroll through the letters and press the START button to decide. Finally, select END to confirm. The time limit for inputting your name is displayed in the upper right corner of the screen. Upon completion of this process by all players, the game proceeds to the next screen.

While loading the game data, the screen remains stationary for a while. You cannot skip this screen.

20

(B) COURSES AND VEHICLES

There are 4 courses in this product.

[BANTHA TRACKS] EASY

The actual course shown in the motion picture has been simplified and shortened for beginners. Huge rocks rise out of the stretched wilderness.

[SMUGGLER’S COVE] NORMAL

A beautiful shoal and moss-covered land can be seen in this course. Although you will face consecutive curves in the course, the difficulty itself is not too high.

[PIXELITO CHALLENGE] HARD

This course is staged in the mountains at night. The narrower road and the number of hairpin curves make it the most difficult among the 4 courses in terms of the course layout.

[THE BOONTA CLASSIC] EXPERT

Tthis course is a reproduction of the course shown in the motion picture . This course is longer than the other 3 courses, making it difficult to stay the course.

There are 4 vehicles to choose from. The vehicles available at the beginning are the ANAKIN SKYWALKER and the SEBULBA. The other 2 can only be used if certain requirements are fulfilled.

Conditions to have the Hidden vehicles appear:

[GASGANO] Must exceed 700 plays total (with any course/character).

[BEN QUADINAROS] In the EXPERT course, game must be completed 50 times (with any character).

*Note that once the vehicles appear, they will not be cleared when the BACKUP RAM CLEAR is performed.

(C) HOW TO OPERATE

THROTTLE LEVER

BRAKE LEVER

(ACCELERATOR)

 

BOOST BUTTON

THROTTLE LEVER

(ACCELERATOR)

 

SELECT BUTTON

SELECT BUTTON

 

START BUTTON

 

DECIDE/VIEW CHANGE

21

The THROTTLE LEVER left & right also function as an accelerator and steering. Incline the THROTTLE LEVER forward to gain speed. To reduce the speed, pull the THROTTLE LEVER toward you. Incline the right Lever forward and pull the left Lever toward you to turn left. Grip the Brake Lever on the right-hand Lever to quickly reduce the speed. The Brake Lever itself is in the digital switch system, however, braking power varies in accordance with the strength of gripping the Lever.

Press the BOOST button on the center of the panel to gain a rapid speed for a certain period of time. The gauge displayed at the lower right screen shows the current BOOST effect. The BOOST power gradually diminishes, and when it becomes zero, acceleration is finished. While the BOOST is in effect, the button is kept pressed down. Once the BOOST becomes active, the button returns to its original state.

Note that setting of not performing the aforementioned operation can be selected.

In that case however, gaining a rapid speed by the BOOST button remains unchanged.

BOOST can be used up to 3 times per race. The BOOST button goes on when active, flashes during use, and goes off when inactive.

The START button can be used for “DECIDE” in the select screen and “VIEW CHANGE” during game. It goes on during the race only.

Use the SELECT button for selecting the course, the vehicle, and the letters in the NAME entry.

BRAKE and LEVER

BRAKE and LEVER

used jointly

used jointly

OPERATION - EFFECT of the LEVER

22

+ 54 hidden pages