Seagate ST3160215AS, ST3320820AS, ST340215AS, ST380815AS, ST3300820AS User Manual

...
0 (0)
Seagate ST3160215AS, ST3320820AS, ST340215AS, ST380815AS, ST3300820AS User Manual

Product Manual

Barracuda 7200.10 Serial ATA

ST3750640AS

ST3250410AS

ST3750840AS

ST3250310AS

ST3500630AS

ST3200820AS

ST3500830AS

ST3160815AS

ST3400620AS

ST3160310AS

ST3400820AS

ST3160215AS

ST3320620AS

ST3120815AS

ST3320820AS

ST3120215AS

ST3300620AS

ST380815AS

ST3300820AS

ST380215AS

ST3250620AS

ST340815AS

ST3250820AS

ST340215AS

100402371 Rev. K December 2007

 

 

evision history

Revision

Date

Sheets affected or comments

Rev. A

05/01/06

Initial release.

Rev. B

07/20/06

1, 3, 14-15, 26-28, 33, 35 and 49

Rev. C

08/14/06

10, 12, 14, 16, 19 and 27-28.

Rev. D

09/26/06

Added 160 - 40GB models

Rev. E

10/04/06

19, 21, 23, 25 and 35

Rev. F

05/04/07

Front cover, 1, 3, 14-15, 26-29, 33, 35, 38, 41-42, 49 and 53-56.

Rev. G

08/23/07

1.

Rev. H

09/06/07

4, 6, 8, 10, 12, 14-16, 27-28 and 35.

Rev. J

11/05/07

4, 6, 8, 10, 12, 14, 16, 18-25 and 27-29.

Rev. K

12/18/07

fc, 1, 3, 18, 26, 28, 35 and 51.

Copyright © 2006-2007 Seagate Technology LLC. All rights reserved. Printed in U.S.A. Publication number: 100402371, Rev. K December 2007

Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Barracuda, SeaTools and SeaTDD are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries. All other trademarks or registered trademarks are the property of their respective owners.

One gigabyte, or GB, equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. Seagate reserves the right to change, without notice, product offerings or specifications.

Contents

1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.1 About the Serial ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2.1 Specification summary tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.2 Formatted capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 2.2.1 LBA mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 2.3 Default logical geometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

2.4 Recording and interface technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 2.5 Physical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 2.6 Seek time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 2.7 Start/stop times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 2.8 Power specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

2.8.1 Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 2.8.2 Conducted noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 2.8.3 Voltage tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 2.8.4 Power-management modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

2.9 Environmental specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 2.9.1 Ambient temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 2.9.2 Temperature gradient. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 2.9.3 Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 2.9.4 Altitude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 2.9.5 Shock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 2.9.6 Vibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

2.10 Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 2.10.1 Test for Prominent Discrete Tones (PDTs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 2.11 Electromagnetic immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

2.12 Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 2.12.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF) . . . 37 2.13 Agency certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 2.13.1 Safety certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 2.13.2 Electromagnetic compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 2.13.3 FCC verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

2.14 Environmental protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 2.14.1 European Union Restriction of Hazardous Substances (RoHS) Directive . . . . . 39 2.14.2 China Restriction of Hazardous Substances (RoHS) Directive . . . . . . . . . . . . . 39

2.15 Corrosive environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

3.0 Configuring and mounting the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

3.1 Handling and static-discharge precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 3.2 Configuring the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 3.3 Serial ATA cables and connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 3.4 Drive mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

4.0 Serial ATA (SATA) interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

4.1 Hot-Plug compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 4.2 Serial ATA device plug connector pin definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 4.3 Supported ATA commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 4.3.1 Identify Device command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 4.3.2 Set Features command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 4.3.3 S.M.A.R.T. commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

5.0 Seagate Technology support services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Barracuda 7200.10 Serial ATA Product Manual, Rev. K

i

ii

Barracuda 7200.10 Serial ATA Product Manual, Rev. K

 

List of Figures

 

Figure 1.

Typical 5V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

31

Figure 2.

Typical 12V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

31

Figure 3.

Serial ATA connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

42

Figure 4.

Attaching SATA cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

42

Figure 5.

Mounting dimensions for 750-200 GB models (except ST3250410AS and ST3250310AS) . 43

Figure 6.

Mounting dimensions for 160-40 GB models (including ST3250410AS and ST3250310AS)

44

Barracuda 7200.10 Serial ATA Product Manual, Rev. K

iii

1.0Introduction

This manual describes the functional, mechanical and interface specifications for the following Seagate Barracuda® 7200.10 Serial ATA model drives:

ST3750640AS

ST3320620AS

ST3250410AS

ST3120815AS

ST3750840AS

ST3320820AS

ST3250310AS

ST3120215AS

ST3500630AS

ST3300620AS

ST3200820AS

ST380815AS

ST3500830AS

ST3300820AS

ST3160815AS

ST380215AS

ST3400620AS

ST3250620AS

ST3160310AS

ST340815AS

ST3400820AS

ST3250820AS

ST3160215AS

ST340215AS

These drives provide the following key features:

7,200 RPM spindle speed.

High instantaneous (burst) data-transfer rates (up to 300 Mbytes per second).

Perpendicular recording and Tunneling Magnetoresistive (TMR) recording heads for increased areal density.

State-of-the-art cache and on-the-fly error-correction algorithms.

Native Command Queueing with command ordering to increase performance in demanding applications.

Full-track multiple-sector transfer capability without local processor intervention.

Quiet operation.

SeaTools diagnostic software performs a drive self-test that eliminates unnecessary drive returns.

Support for S.M.A.R.T. drive monitoring and reporting.

Supports latching SATA cables and connectors.

Barracuda 7200.10 Serial ATA Product Manual, Rev. K

1

1.1About the Serial ATA interface

The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include:

Easy installation and configuration with true plug-and-play connectivity. It is not necessary to set any jumpers or other configuration options.

Thinner and more flexible cabling for improved enclosure airflow and ease of installation.

Scalability to higher performance levels.

In addition, Serial ATA makes the transition from parallel ATA easy by providing legacy software support. Serial ATA was designed to allow you to install a Serial ATA host adapter and Serial ATA disc drive in your current system and expect all of your existing applications to work as normal.

The Serial ATA interface connects each disc drive in a point-to-point configuration with the Serial ATA host adapter. There is no master/slave relationship with Serial ATA devices like there is with parallel ATA. If two drives are attached on one Serial ATA host adapter, the host operating system views the two devices as if they were both “masters” on two separate ports. This essentially means both drives behave as if they are Device 0 (master) devices.

Note. The host adapter may, optionally, emulate a master/slave environment to host software where two devices on separate Serial ATA ports are represented to host software as a Device 0 (master) and Device 1 (slave) accessed at the same set of host bus addresses. A host adapter that emulates a master/slave environment manages two sets of shadow registers. This is not a typical Serial ATA environment.

The Serial ATA host adapter and drive share the function of emulating parallel ATA device behavior to provide backward compatibility with existing host systems and software. The Command and Control Block registers, PIO and DMA data transfers, resets, and interrupts are all emulated.

The Serial ATA host adapter contains a set of registers that shadow the contents of the traditional device registers, referred to as the Shadow Register Block. All Serial ATA devices behave like Device 0 devices. For additional information about how Serial ATA emulates parallel ATA, refer to the “Serial ATA: High Speed Serialized AT Attachment” specification. The specification can be downloaded from www.serialata.org.

2

Barracuda 7200.10 Serial ATA Product Manual, Rev. K

2.0Drive specifications

Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the following drive models:

ST3750640AS

ST3320620AS

ST3250410AS

ST3120815AS

ST3750840AS

ST3320820AS

ST3250310AS

ST3120215AS

ST3500630AS

ST3300620AS

ST3200820AS

ST380815AS

ST3500830AS

ST3300820AS

ST3160815AS

ST380215AS

ST3400620AS

ST3250620AS

ST3160310AS

ST340815AS

ST3400820AS

ST3250820AS

ST3160215AS

ST340215AS

2.1Specification summary tables

The specifications listed in the following tables are for quick reference. For details on specification measurement or definition, see the appropriate section of this manual.

Barracuda 7200.10 Serial ATA Product Manual, Rev. K

3

Table 1:

Drive specifications summary for 750 Gbyte models

 

 

 

 

Drive specification

ST3750640AS

ST3750840AS

 

 

 

Formatted capacitty (512 bytes/sector)*

750 Gbytes

 

 

 

 

Guaranteed sectors

1,465,149,168

 

 

 

 

 

Heads

 

8

 

 

 

 

 

Discs

 

4

 

 

 

 

Bytes per sector

512

 

 

 

 

Default sectors per track

63

 

 

 

 

Default read/write heads

16

 

 

 

 

Default cylinders

16,383

 

 

 

 

Recording density

769 kbits/in avg

 

 

 

 

 

Track density

 

141 ktracks/in avg

 

 

 

 

 

Areal density

 

109 Gbits/in2 avg

 

Spindle speed

 

7,200 RPM

 

 

 

 

Internal data transfer rate

1,030 Mbits/sec max

 

 

 

 

Sustained data transfer rate OD (read)

78 Mbytes/sec max

 

 

 

 

I/O data-transfer rate

300 Mbytes/sec max

 

 

 

 

ATA data-transfer modes supported

PIO modes 0–4

 

 

 

Multiword DMA modes 0–2

 

 

 

Ultra DMA modes 0–6

 

 

 

 

 

Cache buffer

 

16 Mbytes

8 Mbytes

 

 

 

 

Height (max)

 

26.1 mm (1.028 inches)

 

 

 

 

 

Width (max)

 

101.85 mm (4.010 inches)

 

 

 

 

 

Length (max)

 

146.99 mm (5.787 inches)

 

 

 

 

Weight (typical)

720 grams (1.59 lbs)

 

 

 

 

Average latency

4.16 msec

 

 

 

 

Power-on to ready

15 sec max

 

 

 

 

Standby to ready

15 sec max

 

 

 

Track-to-track seek time

<0.8 msec typical read; <1.0 msec typical write

 

 

 

Average seek, read

<8.5 msec typical

 

 

 

 

Average seek, write

<10.0 msec typical

 

 

 

 

Startup current (typical) 12V (peak)

2.8 amps

 

 

 

 

Voltage tolerance (including noise)

5V ± 5%

 

 

 

12V ± 10%

 

Ambient temperature

0° to 60°C (operating)

 

 

 

–40° to 70°C (nonoperating)

 

 

 

 

Temperature gradient

20°C per hour max (operating)

 

 

 

30°C per hour max (nonoperating)

 

 

 

 

Relative humidity

5% to 90% (operating)

 

 

 

5% to 95% (nonoperating)

 

Relative humidity gradient

30% per hour max

 

 

 

 

Wet bulb temperature

37.7°C max (operating)

 

 

 

37.7°C max (nonoperating)

 

 

 

 

Altitude, operating

–60.96 m to 3,048 m

 

 

 

(–200 ft. to 10,000+ ft.)

 

Altitude, nonoperating

–60.96 m to 12,192 m

 

(below mean sea level, max)

(–200 ft. to 40,000+ ft.)

 

 

 

 

Operational Shock

68 Gs at 2 msec max

 

 

 

 

Non-Operational Shock

300 Gs at 2 msec max

 

 

 

 

 

4

Barracuda 7200.10 Serial ATA Product Manual, Rev. K

Drive specification

ST3750640AS

ST3750840AS

Vibration, operating

5–22 Hz: 0.25 Gs, Limited displacement

 

22–350 Hz: 0.50 Gs

 

 

350–500 Hz:: 0.25 Gs

 

 

 

Vibration, nonoperating

5–22 Hz: 0.25 Gs, Limited displacement

 

22–350 Hz: 5.0 Gs

 

 

350–500 Hz:: 1.0 Gs

 

 

 

 

Drive acoustics, sound power

 

 

Idle**

2.8 bels (typical)

 

 

3.0 bels (max)

 

Performance seek

3.7 bels (typical)

 

 

3.9 bels (max)

 

 

 

 

Nonrecoverable read errors

1 per 1014 bits read

 

Annualized Failure Rate (AFR)

0.34%

 

 

 

 

Warranty

5 years on distribution units.

 

 

To determine the warranty for a specific drive, use a web browser to

 

access the following web page: www.seagate.com/support/service/

 

From this page, click on the “Verify Your Warranty” link. You will be asked

 

to provide the drive serial number, model number (or part number) and

 

country of purchase. The system will display the warranty information for

 

your drive.

 

 

 

 

Contact start-stop cycles

50,000 at 25°C, 50% rel. humidity

 

 

 

 

Supports Hotplug operation per the Serial ATA Revision

Yes

 

2.5 specification

 

 

 

 

 

*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting.

**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels.

Barracuda 7200.10 Serial ATA Product Manual, Rev. K

5

Table 2:

Drive specifications summary for 500 Gbyte models

 

 

 

 

Drive specification

ST3500630AS

 

ST3500830AS

 

 

 

 

Formatted capacity (512 bytes/sector)*

500 Gbytes

 

 

 

 

 

 

Guaranteed sectors

976,773,168

 

 

 

 

 

 

 

Heads

 

6

 

 

 

 

 

 

 

Discs

 

3

 

 

 

 

 

 

Bytes per sector

512

 

 

 

 

 

 

Default sectors per track

63

 

 

 

 

 

 

Default read/write heads

16

 

 

 

 

 

 

Default cylinders

16,383

 

 

 

 

 

 

Recording density

769 kbits/in avg

 

 

 

 

 

 

 

Track density

 

141 ktracks/in avg

 

 

 

 

 

 

 

Areal density

 

109 Gbits/in2 avg

 

 

Spindle speed

 

7,200 RPM

 

 

 

 

 

 

Internal data transfer rate

1,030 Mbits/sec max

 

 

 

 

 

 

Sustained data transfer rate OD (read)

72 Mbytes/sec max

 

 

 

 

 

 

I/O data-transfer rate

300 Mbytes/sec max

 

 

 

 

 

 

ATA data-transfer modes supported

PIO modes 0–4

 

 

 

 

Multiword DMA modes 0–2

 

 

Ultra DMA modes 0–6

 

 

 

 

 

 

 

Cache buffer

 

16 Mbytes

 

8 Mbytes

 

 

 

 

 

Height (max)

 

26.1 mm (1.028 inches)

 

 

 

 

 

Width (max)

 

101.85 mm (4.010 inches)

 

 

 

Length (max)

 

146.99 mm (5.787 inches)

 

 

 

 

Weight (typical)

635 grams (1.40 lbs)

 

 

 

 

 

 

Average latency

4.16 msec

 

 

 

 

 

 

Power-on to ready

15 sec max

 

 

 

 

 

 

Standby to ready

15 sec max

 

 

 

 

 

Track-to-track seek time

<0.8 msec typical read;

<1.0 msec typical write

 

 

 

 

Average seek, read

<8.5 msec typical

 

 

 

 

 

 

Average seek, write

<10.0 msec typical

 

 

 

 

 

 

Startup current (typical) 12V (peak)

2.8 amps

 

 

 

 

 

 

Voltage tolerance (including noise)

5V ± 5%

 

 

 

 

12V ± 10%

 

 

Ambient temperature

0° to 60°C (operating)

 

 

 

 

–40° to 70°C (nonoperating)

 

 

Temperature gradient (max)

20°C per hour (operating)

 

 

30°C per hour (nonoperating)

 

 

 

 

Relative humidity

5% to 90% (operating)

 

 

 

 

5% to 95% (nonoperating)

Relative humidity gradient

30% per hour max

 

 

 

 

 

 

Wet bulb temperature (max)

37.7 °C (operating)

 

 

 

 

37.7 °C (nonoperating)

 

 

 

 

 

 

Altitude, operating

–60.96 m to 3,048 m

 

 

 

 

(–200 ft. to 10,000+ ft.)

 

 

Altitude, nonoperating

–60.96 m to 12,192 m

 

 

(below mean sea level, max)

(–200 ft. to 40,000+ ft.)

 

 

 

 

 

 

Operational Shock

68 Gs max at 2 msec

 

 

 

 

 

 

Non-Operational Shock

300 Gs max at 2 msec

 

 

 

 

 

 

 

6

Barracuda 7200.10 Serial ATA Product Manual, Rev. K

Drive specification

ST3500630AS

ST3500830AS

Vibration, operating

5–22 Hz: 0.25 Gs, Limited displacement

 

 

22–350 Hz: 0.50 Gs

 

 

350–500 Hz:: 0.25 Gs

 

 

 

 

Vibration, nonoperating

5–22 Hz: 0.25 Gs, Limited displacement

 

 

22–350 Hz: 5.0 Gs

 

 

350–500 Hz:: 1.0 Gs

 

 

 

 

Drive acoustics, sound power

 

 

Idle**

2.8 bels (typical)

 

 

3.0 bels (max)

 

Performance seek

3.7 bels (typical)

 

 

3.9 bels (max)

 

 

 

 

Nonrecoverable read errors

1 per 1014 bits read

 

Annualized Failure Rate (AFR)

0.34%

 

 

 

 

Warranty

5 years on distribution units.

 

 

To determine the warranty for a specific drive, use a web browser to access

 

the following web page: www.seagate.com/support/service/

 

From this page, click on the “Verify Your Warranty” link. You will be asked to

 

provide the drive serial number, model number (or part number) and country

 

of purchase. The system will display the warranty information for your drive.

 

 

 

Contact start-stop cycles

50,000 at 25°C, 50% rel. humidity

 

 

 

 

Supports Hotplug operation per the Serial ATA Revi-

Yes

 

sion 2.5 specification

 

 

 

 

 

*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting.

**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels.

Barracuda 7200.10 Serial ATA Product Manual, Rev. K

7

Table 3:

Drive specifications summary for 400 Gbyte models

 

 

 

 

Drive specification

ST3400620AS

 

ST3400820AS

 

 

 

 

Formatted capacity (512 bytes/sector)*

400 Gbytes

 

 

 

 

 

 

Guaranteed sectors

781,422,768

 

 

 

 

 

 

 

Heads

 

5

 

 

 

 

 

 

 

Doscs

 

3

 

 

 

 

 

 

Bytes per sector

512

 

 

 

 

 

 

Default sectors per track

63

 

 

 

 

 

 

Default read/write heads

16

 

 

 

 

 

 

Default cylinders

16,383

 

 

 

 

 

 

Recording density

769 kbits/in avg

 

 

 

 

 

 

 

Track density

 

141 ktracks/in avg

 

 

 

 

 

 

 

Areal density

 

109 Gbits/in2 avg

 

 

Spindle speed

 

7,200 RPM

 

 

 

 

 

 

Internal data transfer rate

1,030 Mbits/sec max

 

 

 

 

 

 

Sustained data transfer rate OD (read)

72 Mbytes/sec max

 

 

 

 

 

 

I/O data-transfer rate

300 Mbytes/sec max

 

 

 

 

 

 

ATA data-transfer modes supported

PIO modes 0–4

 

 

 

 

Multiword DMA modes 0–2

 

 

Ultra DMA modes 0–6

 

 

 

 

 

 

 

Cache buffer

 

16 Mbytes

 

8 Mbytes

 

 

 

 

 

Height (max)

 

26.1 mm (1.028 inches)

 

 

 

 

 

Width (max)

 

101.85 mm (4.010 inches)

 

 

 

Length (max)

 

146.99 mm (5.787 inches)

 

 

 

 

Weight (typical)

635 grams (1.40 lbs)

 

 

 

 

 

 

Average latency

4.16 msec

 

 

 

 

 

 

Power-on to ready

15 sec max

 

 

 

 

 

 

Standby to ready

15 sec max

 

 

 

 

 

Track-to-track seek time

<0.8 msec typical read;

<1.0 msec typical write

 

 

 

 

Average seek, read

<8.5 msec typical

 

 

 

 

 

 

Average seek, write

<10.0 msec typical

 

 

 

 

 

 

Startup current (typical) 12V (peak)

2.8 amps

 

 

 

 

 

 

Voltage tolerance (including noise)

5V ± 5%

 

 

 

 

12V ± 10%

 

 

Ambient temperature

0° to 60°C (operating)

 

 

 

 

–40° to 70°C (nonoperating)

 

 

Temperature gradient

20°C per hour max (operating)

 

 

30°C per hour max (nonoperating)

 

 

 

 

Relative humidity

5% to 90% (operating)

 

 

 

 

5% to 95% (nonoperating)

Relative humidity gradient

30% per hour max

 

 

 

 

 

 

Wet bulb temperature

37.7 °C max (operating)

 

 

 

 

37.7 °C max (nonoperating)

 

 

 

 

Altitude, operating

–60.96 m to 3,048 m

 

 

 

 

(–200 ft. to 10,000+ ft.)

 

 

Altitude, nonoperating

–60.96 m to 12,192 m

 

 

(below mean sea level, max)

(–200 ft. to 40,000+ ft.)

 

 

 

 

 

 

Operational Shock

68 Gs max at 2 msec

 

 

 

 

 

 

Non-Operational Shock

300 Gs max at 2 msec

 

 

 

 

 

 

 

8

Barracuda 7200.10 Serial ATA Product Manual, Rev. K

Drive specification

ST3400620AS

 

ST3400820AS

Vibration, operating

5–22 Hz: 0.25 Gs, Limited displacement

 

 

22–350 Hz: 0.50 Gs

 

 

350–500 Hz:: 0.25 Gs

 

 

 

 

Vibration, nonoperating

5–22 Hz: 0.25 Gs, Limited displacement

 

 

22–350 Hz: 5.0 Gs

 

 

350–500 Hz:: 1.0 Gs

 

 

 

 

 

Drive acoustics, sound power

 

 

 

Idle**

2.7 bels (typical)

 

 

2.9 bels (max)

 

Performance seek

3.4 bels (typical)

 

 

3.6 bels (max)

 

 

 

 

Nonrecoverable read errors

1 per 1014 bits read

 

Annualized Failure Rate (AFR)

0.34%

 

 

 

 

 

Warranty

5 years on distribution units.

 

 

To determine the warranty for a specific drive, use a web browser to

 

access the following web page: www.seagate.com/support/service/

 

From this page, click on the “Verify Your Warranty” link. You will be asked

 

to provide the drive serial number, model number (or part number) and

 

country of purchase. The system will display the warranty information for

 

your drive.

 

 

 

 

Contact start-stop cycles

50,000 at 25°C, 50% rel. humidity

 

 

 

 

Supports Hotplug operation per the Serial ATA Revision

Yes

 

2.5 specification

 

 

 

 

 

 

 

*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting.

**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels.

Barracuda 7200.10 Serial ATA Product Manual, Rev. K

9

Table 4:

Drive specifications summary for 320 Gbyte models

 

 

 

 

 

 

Drive specification

ST3320620AS

 

ST3320820AS

 

 

 

 

Formatted capacity (512 bytes/sector)*

320 Gbytes

 

 

 

 

 

 

Guaranteed sectors

625,142,448

 

 

 

 

 

 

 

Heads

 

4

 

 

 

 

 

 

 

Discs

 

2

 

 

 

 

 

 

Bytes per sector

512

 

 

 

 

 

 

Default sectors per track

63

 

 

 

 

 

 

Default read/write heads

16

 

 

 

 

 

 

Default cylinders

16,383

 

 

 

 

 

 

Recording density

769 kbits/in avg

 

 

 

 

 

 

 

Track density

 

141 ktracks/in avg

 

 

 

 

 

 

 

Areal density

 

109 Gbits/in2 avg

 

 

Spindle speed

 

7,200 RPM

 

 

 

 

 

 

Internal data transfer rate

1,030 Mbits/sec max

 

 

 

 

 

 

Sustained data transfer rate OD (read)

72 Mbytes/sec max

 

 

 

 

 

 

I/O data-transfer rate

300 Mbytes/sec max

 

 

 

 

 

 

ATA data-transfer modes supported

PIO modes 0–4

 

 

 

 

Multiword DMA modes 0–2

 

 

Ultra DMA modes 0–6

 

 

 

 

 

 

 

Cache buffer

 

16 Mbytes

 

8 Mbytes

 

 

 

 

 

Height (max)

 

26.1 mm (1.028 inches)

 

 

 

 

 

Width (max)

 

101.85 mm (4.010 inches)

 

 

 

Length (max)

 

146.99 mm (5.787 inches)

 

 

 

 

Weight (typical)

635 grams (1.40 lbs)

 

 

 

 

 

 

Average latency

4.16 msec

 

 

 

 

 

 

Power-on to ready

15 sec max

 

 

 

 

 

 

Standby to ready

15 sec max

 

 

 

 

 

Track-to-track seek time

<0.8 msec typical read;

<1.0 typical write

 

 

 

 

Average seek, read

<8.5 msec typical

 

 

 

 

 

 

Average seek, write

<10.0 msec typical

 

 

 

 

 

 

Startup current (typical) 12V (peak)

2.8 amps

 

 

 

 

 

 

Voltage tolerance (including noise)

5V ± 5%

 

 

 

 

12V ± 10%

 

 

Ambient temperature

0° to 60°C (operating)

 

 

 

 

–40° to 70°C (nonoperating)

 

 

Temperature gradient

20°C per hour max (operating)

 

 

30°C per hour max (nonoperating)

 

 

 

 

Relative humidity

5% to 90% (operating)

 

 

 

 

5% to 95% (nonoperating)

Relative humidity gradient

30% per hour max

 

 

 

 

 

 

Wet bulb temperature

37.7°C max (operating)

 

 

 

 

37.7°C max (nonoperating)

 

 

 

 

Altitude, operating

–60.96 m to 3,048 m

 

 

 

 

(–200 ft. to 10,000+ ft.)

 

 

Altitude, nonoperating

–60.96 m to 12,192 m

 

 

(below mean sea level, max)

(–200 ft. to 40,000+ ft.)

 

 

 

 

 

 

Operational Shock

68 Gs max at 2 msec

 

 

 

 

 

 

Non-Operational Shock

350 Gs max at 2 msec

 

 

 

 

 

 

 

10

Barracuda 7200.10 Serial ATA Product Manual, Rev. K

Drive specification

ST3320620AS

ST3320820AS

Vibration, operating

5–22 Hz: 0.25 Gs, Limited displacement

 

22–350 Hz: 0.50 Gs

 

 

350–500 Hz:: 0.25 Gs

 

 

 

Vibration, nonoperating

5–22 Hz: 0.25 Gs, Limited displacement

 

22–350 Hz: 5.0 Gs

 

 

350–500 Hz:: 1.0 Gs

 

 

 

 

Drive acoustics, sound power

 

 

Idle**

2.5 bels (typical)

 

 

2.9 bels (max)

 

Performance seek

3.0 bels (typical)

 

 

3.2 bels (max)

 

 

 

 

Nonrecoverable read errors

1 per 1014 bits read

 

Annualized Failure Rate (AFR)

0.34%

 

 

 

 

Warranty

5 years on distribution units.

 

 

To determine the warranty for a specific drive, use a web browser to

 

access the following web page: www.seagate.com/support/service/

 

From this page, click on the “Verify Your Warranty” link. You will be

 

asked to provide the drive serial number, model number (or part num-

 

ber) and country of purchase. The system will display the warranty

 

information for your drive.

 

 

 

 

Contact start-stop cycles

50,000 at 25°C, 50% rel. humidity

 

 

 

 

Supports Hotplug operation per the Serial ATA Revision 2.5

Yes

 

specification

 

 

 

 

 

*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting.

**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels.

Barracuda 7200.10 Serial ATA Product Manual, Rev. K

11

Table 5:

Drive specifications summary for 300 Gbyte models

 

 

 

 

Drive specification

ST3300620AS

 

ST3300820AS

 

 

 

 

Formatted capacity (512 bytes/sector)*

300 Gbytes

 

 

 

 

 

 

Guaranteed sectors

586,072,368

 

 

 

 

 

 

 

Heads

 

3

 

 

 

 

 

 

 

Discs

 

2

 

 

 

 

 

 

Bytes per sector

512

 

 

 

 

 

 

Default sectors per track

63

 

 

 

 

 

 

Default read/write heads

16

 

 

 

 

 

 

Default cylinders

16,383

 

 

 

 

 

 

Recording density

769 kbits/in avg

 

 

 

 

 

 

 

Track density

 

141 ktracks/in avg

 

 

 

 

 

 

 

Areal density

 

109 Gbits/in2 avg

 

 

Spindle speed

 

7,200 RPM

 

 

 

 

 

 

Internal data transfer rate

1,030 Mbits/sec max

 

 

 

 

 

 

Sustained data transfer rate OD (read)

72 Mbytes/sec max

 

 

 

 

 

 

I/O data-transfer rate

300 Mbytes/sec max

 

 

 

 

 

 

ATA data-transfer modes supported

PIO modes 0–4

 

 

 

 

Multiword DMA modes 0–2

 

 

Ultra DMA modes 0–6

 

 

 

 

 

 

 

Cache buffer

 

16 Mbytes

 

8 Mbytes

 

 

 

 

 

Height (max)

 

26.1 mm (1.028 inches)

 

 

 

 

 

Width (max)

 

101.85 mm (4.010 inches)

 

 

 

Length (max)

 

146.99 mm (5.787 inches)

 

 

 

 

Weight (typical

600 grams (1.32 lb.)

 

 

 

 

 

 

Average latency

4.16 msec

 

 

 

 

 

 

Power-on to ready

11 sec max

 

 

 

 

 

 

Standby to ready

11 sec max

 

 

 

 

 

Track-to-track seek time

<0.8 msec typical read;

<1.0 msec typical write

 

 

 

 

Average seek, read

<8.5 msec typical

 

 

 

 

 

 

Average seek, write

<10.0 msec typical

 

 

 

 

 

 

Startup current (typical) 12V (peak)

2.8 amps

 

 

 

 

 

 

Voltage tolerance (including noise)

5V ± 5%

 

 

 

 

12V ± 10%

 

 

Ambient temperature

0° to 60°C (operating)

 

 

 

 

–40° to 70°C (nonoperating)

 

 

Temperature gradient

20°C per hour max (operating)

 

 

30°C per hour max (nonoperating)

 

 

 

 

Relative humidity

5% to 90% (operating)

 

 

 

 

5% to 95% (nonoperating)

Relative humidity gradient

30% per hour max

 

 

 

 

 

 

Wet bulb temperature

37.7°C max (operating)

 

 

 

 

37.7°C max (nonoperating)

 

 

 

 

Altitude, operating

–60.96 m to 3,048 m

 

 

 

 

(–200 ft. to 10,000+ ft.)

 

 

Altitude, nonoperating

–60.96 m to 12,192 m

 

 

(below mean sea level, max)

(–200 ft. to 40,000+ ft.)

 

 

 

 

 

 

Operational Shock

68 Gs max at 2 msec

 

 

 

 

 

 

Non-Operational Shock

350 Gs max at 2 msec

 

 

 

 

 

 

 

12

Barracuda 7200.10 Serial ATA Product Manual, Rev. K

Drive specification

ST3300620AS

ST3300820AS

Vibration, operating

5–22 Hz: 0.25 Gs, Limited displacement

 

22–350 Hz: 0.50 Gs

 

 

350–500 Hz:: 0.25 Gs

 

 

 

Vibration, nonoperating

5–22 Hz: 0.25 Gs, Limited displacement

 

22–350 Hz: 5.0 Gs

 

 

350–500 Hz:: 1.0 Gs

 

 

 

 

Drive acoustics, sound power

 

 

Idle**

2.5 bels (typical)

 

 

2.9 bels (max)

 

Performance seek

3.0 bels (typical)

 

 

3.2 bels (max)

 

 

 

 

Nonrecoverable read errors

1 per 1014 bits read

 

Annualized Failure Rate (AFR)

0.34%

 

 

 

 

Warranty

5 years on distribution units.

 

 

To determine the warranty for a specific drive, use a web browser to

 

access the following web page: www.seagate.com/support/service/

 

From this page, click on the “Verify Your Warranty” link. You will be

 

asked to provide the drive serial number, model number (or part num-

 

ber) and country of purchase. The system will display the warranty infor-

 

mation for your drive.

 

 

 

 

Contact start-stop cycles

50,000 at 25°C, 50% rel. humidity

 

 

 

 

Supports Hotplug operation per the Serial ATA Revision

Yes

 

2.5 specification

 

 

 

 

 

*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting.

**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels.

Barracuda 7200.10 Serial ATA Product Manual, Rev. K

13

Table 6:

Drive specifications summary for 250 Gbyte models

 

 

 

 

 

 

 

 

 

 

Drive specification

ST3250620AS

 

ST3250820AS

ST3250410AS

 

ST3250310AS

 

 

 

 

 

 

 

Formatted capacity (512 bytes/sector)*

250 Gbytes

 

 

 

 

 

 

 

 

 

 

 

Guaranteed sectors

488,397,168

 

 

 

 

 

 

 

 

 

 

 

 

 

Heads

 

3

 

 

2

 

 

 

 

 

 

 

 

 

 

Discs

 

2

 

 

1

 

 

 

 

 

 

 

 

 

Bytes per sector

512

 

 

 

 

 

 

 

 

 

 

 

 

Default sectors per track

63

 

 

 

 

 

 

 

 

 

 

 

 

Default read/write heads

16

 

 

 

 

 

 

 

 

 

 

 

 

Default cylinders

16,383

 

 

 

 

 

 

 

 

 

 

 

Recording density

769 kbits/in avg

 

1,049 kbits/in avg

 

 

 

 

 

 

 

Track density

 

141 ktracks/in avg

 

155 ktracks/in avg

 

 

 

 

 

 

 

Areal density

 

109 Gbits/in2 avg

 

163 Gbits/in2 avg

 

Spindle speed

 

7,200 RPM

 

 

 

 

 

 

 

 

 

 

Internal data transfer rate

1,030 Mbits/sec max

 

1,212 Mbits/sec max

 

 

 

 

 

 

Sustained data transfer rate OD (read)

72 Mbytes/sec max

 

106 Mbytes/sec max

 

 

 

 

 

 

 

I/O data-transfer rate

300 Mbytes/sec max

 

 

 

 

 

 

 

 

 

 

ATA data-transfer modes supported

PIO modes 0–4

 

 

 

 

 

 

Multiword DMA modes 0–2

 

 

 

 

 

Ultra DMA modes 0–6

 

 

 

 

 

 

 

 

 

 

 

Cache buffer

 

16 Mbytes

 

8 Mbytes

16 Mbytes

 

8 Mbytes

 

 

 

 

 

 

Height (max)

 

26.1 mm (1.028 inches)

19.99 mm (.787 inches)

 

 

 

 

 

 

Width (max)

 

101.85 mm (4.010 inches)

 

 

 

 

 

 

 

 

 

Length (max)

 

146.99 mm (5.787 inches)

 

 

 

 

 

 

 

 

 

Weight (typical)

600 grams (1.32 lb.)

 

380 grams (0.838lb.)

 

 

 

 

 

 

 

Average latency

4.16 msec

 

 

 

 

 

 

 

 

 

 

Power-on to ready

11 sec max

 

7.9 sec max

 

 

 

 

 

 

Standby to ready

11 sec max

 

7.9 sec max

 

 

 

 

 

 

Track-to-track seek time

<0.8 msec typical read,

 

<0.8 msec typical read,

 

 

 

<1.0 msec typical write

 

<1.0 msec typical write

 

 

 

 

 

 

Average seek, read

<8.5 msec typical

 

<11.0 msec typical

 

 

 

 

 

 

Average seek, write

<10.0 msec typical

 

<12.0 msec typical

 

 

 

 

 

 

Startup current (typical) 12V (peak)

2.8 amps

 

2.0 amps

 

 

 

 

 

 

 

Voltage tolerance (including noise)

5V ± 5%

 

 

 

 

 

 

12V ± 10%

 

 

 

 

 

 

 

 

 

Ambient temperature

0° to 60°C per hour max (operating)

 

 

 

 

 

–40° to 70°C per hour max (nonoperating)

 

 

 

Temperature gradient

20°C (operating)

 

 

 

 

 

 

30°C (nonoperating)

 

 

 

 

 

 

 

 

 

 

Relative humidity

5% to 90% (operating)

 

 

 

 

 

 

5% to 95% (nonoperating)

 

 

 

 

 

 

 

 

 

Relative humidity gradient

30% per hour max

 

 

 

 

 

 

 

 

 

 

Wet bulb temperature

37.7°C max (operating)

 

 

 

 

 

 

37.7°C max (nonoperating)

 

 

 

 

 

 

 

 

 

Altitude, operating

–60.96 m to 3,048 m

 

 

 

 

 

 

(–200 ft. to 10,000+ ft.)

 

 

 

 

 

 

 

 

 

 

Altitude, nonoperating

–60.96 m to 12,192 m

 

 

 

 

(below mean sea level, max)

(–200 ft. to 40,000+ ft.)

 

 

 

 

Operational Shock

68 Gs max at 2 msec

 

63 Gs max at 2 msec

 

 

 

 

 

 

 

Non-Operational Shock

350 Gs max at 2 msec

 

 

 

 

 

 

 

 

 

 

 

 

14

Barracuda 7200.10 Serial ATA Product Manual, Rev. K

Drive specification

ST3250620AS

 

ST3250820AS

 

ST3250410AS

ST3250310AS

 

 

 

 

 

 

Vibration, operating

5–22 Hz: 0.25 Gs, Limited displacement

 

 

 

22–350 Hz: 0.50 Gs

 

 

 

 

 

350–500 Hz:: 0.25 Gs

 

 

 

 

Vibration, nonoperating

5–22 Hz: 0.25 Gs, Limited displacement

 

 

 

22–350 Hz: 5.0 Gs

 

 

 

 

 

350–500 Hz:: 1.0 Gs

 

 

 

 

 

 

 

 

 

 

 

Drive acoustics, sound power

 

 

 

 

 

 

Idle**

2.5 bels (typical)

 

 

2.6 bels (typical)

 

 

 

 

 

2.9 bels (max)

 

 

2.7 bels (max)

 

Performance seek

3.0 bels (typical)

 

 

 

 

 

3.2 bels (max)

 

 

 

 

Quiet seek

 

 

 

 

2.7 bels (typical)

 

 

 

 

 

 

2.8 bels (max)

 

 

 

 

 

 

 

Nonrecoverable read errors

1 per 1014 bits read

 

 

 

 

Annualized Failure Rate (AFR)

0.34%

 

 

 

 

 

 

 

 

 

Warranty

5 years on distribution units.

 

 

 

To determine the warranty for a specific drive, use a web browser to access the following

 

web page: www.seagate.com/support/service/

 

 

 

From this page, click on the “Verify Your Warranty” link. You will be asked to provide the

 

drive serial number, model number (or part number) and country of purchase. The system

 

will display the warranty information for your drive.

 

 

 

 

 

Contact start-stop cycles

50,000 at 25°C, 50% rel. humidity

 

 

 

 

 

 

 

 

Supports Hotplug operation per the

Yes

 

 

 

 

Serial ATA Revision 2.5 specification

 

 

 

 

 

 

 

 

 

 

 

 

 

*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting.

**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels.

Barracuda 7200.10 Serial ATA Product Manual, Rev. K

15

Loading...
+ 47 hidden pages