Seagate ST3640623AS, ST3320613AS, ST31500341AS, ST3320813AS, ST31000333AS User Manual

...
0 (0)
Product Manual
Barracuda 7200.11 Serial ATA
ST31500341AS
ST31000333AS
ST3640323AS
ST3640623AS
ST3320613AS
ST3320813AS
ST3160813AS
100507013 Rev. C August 2008
Revision history
Revision Date Sheets affected or comments
Rev A 06/17/08 Initial release Rev. B 06/25/08 4 and 6. Rev. C (Draft 1) 07/15/08 fc, 1, 3-6, 8-11, 13-15, 17, 21,25-26, 28 and 30.
Publication number: 100507013, Rev. C, August 2008
Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Barracuda, SeaTools and SeaTDD are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries. All other trademarks or registered trademarks are the property of their respective owners.
When referring to hard drive capacity, one gigabyte, or GB, equals one billion bytes and one terabyte, or TB, equals one trillion bytes. Your computer's operating system may use a different standard of measure ment and report a lower capacity. In addition, some of the listed capacity is used for formatting and other functions, and thus will not be available for data storage. Seagate reserves the right to change, without notice, product offerings or specifications
-
Contents
1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 About the Serial ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.1 Formatted capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.1.1 LBA mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.2 Default logical geometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.3 Recording and interface technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.4 Physical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.5 Seek time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.6 Start/stop times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.7 Power specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.7.1 Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.7.2 Conducted noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.7.3 Voltage tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.7.4 Power-management modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.8 Environmental specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.8.1 Ambient temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.8.2 Temperature gradient. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.8.3 Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.8.4 Altitude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.8.5 Shock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.8.6 Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.9 Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.9.1 Test for Prominent Discrete Tones (PDTs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.10 Electromagnetic immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.11 Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.11.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF) . . . 18
2.12 Agency certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.12.1 Safety certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.12.2 Electromagnetic compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.12.3 FCC verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.13 Environmental protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.13.1 European Union Restriction of Hazardous Substances (RoHS) Directive . . . . . 20
2.13.2 China Restriction of Hazardous Substances (RoHS) Directive . . . . . . . . . . . . . 20
2.14 Corrosive environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.0 Configuring and mounting the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.1 Handling and static-discharge precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.2 Configuring the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.3 Serial ATA cables and connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.4 Drive mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.0 Serial ATA (SATA) interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.1 Hot-Plug compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.2 Serial ATA device plug connector pin definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4.3 Supported ATA commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4.3.1 Identify Device command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.3.2 Set Features command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
4.3.3 S.M.A.R.T. commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
5.0 Seagate Technology support services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Barracuda 7200.11 Serial ATA Product Manual, Rev. C i
ii Barracuda 7200.11 Serial ATA Product Manual, Rev. C
List of Figures
Figure 1. Serial ATA connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Figure 2. Attaching SATA cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Figure 3. Mounting dimensions (1500, 1000 and 640 GB models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Figure 4. Mounting dimensions (320 and 160 GB models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Barracuda 7200.11 Serial ATA Product Manual, Rev. C iii

1.0 Introduction

This manual describes the functional, mechanical and interface specifications for the following Seagate Barracuda
ST31500341AS ST31000333AS ST3640323AS ST3640623AS
ST3320613AS ST3320813AS ST3160813AS
These drives provide the following key features:
• 7,200 RPM spindle speed.
• High instantaneous (burst) data-transfer rates (up to 300 Mbytes per second).
• Perpendicular recording, Tunneling Magnetoresistive (TMR) recording heads and EPRML technology, for increased areal density.
• State-of-the-art cache and on-the-fly error-correction algorithms.
• Native Command Queueing with command ordering to increase performance in demanding applications.
• Full-track multiple-sector transfer capability without local processor intervention.
• Quiet operation.
• SeaTools diagnostic software performs a drive self-test that eliminates unnecessary drive returns.
• Support for S.M.A.R.T. drive monitoring and reporting.
• Supports latching SATA cables and connectors.
• Worldwide Name (WWN) capability uniquely identifies the drive.
®
7200.11 Serial ATA model drives:
Barracuda 7200.11 Serial ATA Product Manual, Rev. C 1

1.1 About the Serial ATA interface

The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include:
• Easy installation and configuration with true plug-and-play connectivity. It is not necessary to set any jump­ers or other configuration options.
• Thinner and more flexible cabling for improved enclosure airflow and ease of installation.
• Scalability to higher performance levels.
In addition, Serial ATA makes the transition from parallel ATA easy by providing legacy software support. Serial ATA was designed to allow you to install a Serial ATA host adapter and Serial ATA disc drive in your current system and expect all of your existing applications to work as normal.
The Serial ATA interface connects each disc drive in a point-to-point configuration with the Serial ATA host adapter. There is no master/slave relationship with Serial ATA devices like there is with parallel ATA. If two drives are attached on one Serial ATA host adapter, the host operating system views the two devices as if they were both “masters” on two separate ports. This essentially means both drives behave as if they are Device 0 (master) devices.
Note. The host adapter may, optionally, emulate a master/slave environment to host software where two
devices on separate Serial ATA ports are represented to host software as a Device 0 (master) and Device 1 (slave) accessed at the same set of host bus addresses. A host adapter that emulates a master/slave environment manages two sets of shadow registers. This is not a typical Serial ATA environment.
The Serial ATA host adapter and drive share the function of emulating parallel ATA device behavior to provide backward compatibility with existing host systems and software. The Command and Control Block registers, PIO and DMA data transfers, resets, and interrupts are all emulated.
The Serial ATA host adapter contains a set of registers that shadow the contents of the traditional device regis­ters, referred to as the Shadow Register Block. All Serial ATA devices behave like Device 0 devices. For addi­tional information about how Serial ATA emulates parallel ATA, refer to the “Serial ATA International Organization: Serial ATA Revision 2.6”. The specification can be downloaded from www.sata-io.org.
2 Barracuda 7200.11 Serial ATA Product Manual, Rev. C

2.0 Drive specifications

Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the following drive models:
ST31500341AS ST31000333AS ST3640323AS ST3640623AS
ST3320613AS ST3320813AS ST3160813AS
Specification summary tables
The specifications listed in the following tables are for quick reference. For details on specification measure­ment or definition, see the appropriate section of this manual.
Barracuda 7200.11 Serial ATA Product Manual, Rev. C 3
Table 1: Drive specifications summary for 1500 and 1000 Gbyte models
Drive specification ST31500341AS ST31000333AS
Formatted capacity (512 bytes/sector)* 1500 Gbytes 1000 Gbytes
Guaranteed sectors 2,930,277,168 1,953,525,168
Heads 8 6
Discs 4 3
Bytes per sector 512
Default sectors per track 63
Default read/write heads 16
Default cylinders 16,383
Recording density 1462 kbits/in max 1300 kbits/in max
Track density 190 ktracks/in avg 182 ktracks/in avg
Areal density 277 Gbits/in2 avg 228 Gbits/in2 avg
Spindle speed 7,200 RPM
Internal data transfer rate 1709 Mbits/sec max 1520 Mbits/sec max
Sustained data transfer rate OD 135 Mbytes/sec max 120 Mbytes/sec max
I/O data-transfer rate 300 Mbytes/sec max
ATA data-transfer modes supported PIO modes 0–4
Cache buffer 32 Mbytes
Height (max) 26.1 mm (1.028 inches)
Width (max) 101.6 mm (4.000 inches) +/- 0.010 inches
Length (max) 146.99 mm (5.787 inches)
Weight (typical) 720 grams (1.587 lb.) 630 grams ( 1.389 lb.)
Average latency 4.16 msec
Power-on to ready 20 sec max
Standby to ready 15 sec max
Track-to-track seek time <0.8 msec typical read;
Average seek, read <8.5 msec typical
Average seek, write <10.0 msec typical
Startup current (typical) 12V (peak) 2.8 amps
Voltage tolerance (including noise) 5V +10% / -7.5%
Ambient temperature 0° to 60°C (operating)
Temperature gradient 20°C per hour max (operating)
Relative humidity 5% to 95% (operating)
Relative humidity gradient 30% per hour max
Wet bulb temperature 37.7°C max (operating)
Altitude, operating –60.96 m to 3,048 m
Altitude, nonoperating (below mean sea level, max)
Operational Shock 70 Gs max at 2 msec
Non-Operational Shock 300 Gs max at 2 msec
Multiword DMA modes 0–2 Ultra DMA modes 0–6
<1.0 msec typical write
12V +10% / -7.5%
–40° to 70°C (nonoperating)
30°C per hour max (nonoperating)
5% to 95% (nonoperating)
40.0°C max (nonoperating)
(–200 ft. to 10,000+ ft.)
–60.96 m to 12,192 m (–200 ft. to 40,000+ ft.)
4 Barracuda 7200.11 Serial ATA Product Manual, Rev. C
Drive specification ST31500341AS ST31000333AS
Vibration, operating 2–22 Hz: 0.25 Gs, Limited displacement
Vibration, nonoperating 5–22 Hz: 2.0 Gs
Drive acoustics, sound power
Idle** 2.6 bels (typical)
Performance Seek 3.0 bels (typical)
Quiet Seek 2.7 bels (typical)
Nonrecoverable read errors 1 per 10
Annualized Failure Rate (AFR) 0.34%
Warranty 5 years on distribution units.
Contact start-stop cycles 50,000 at 25°C, 50% rel. humidity
Supports Hotplug operation per the Serial ATA Revision 2.5 specification
22–350 Hz: 0.50 Gs 350–500 Hz:: 0.25 Gs
22–350 Hz: 5.0 Gs 350–500 Hz:: 2.0 Gs
2.8 bels (max)
3.2 bels (max)
2.9 bels (max)
14
bits read
To determine the warranty for a specific drive, use a web browser to access the following web page: From this page, click on the “Verify Your Warranty” link. You will be asked to provide the drive serial number, model number (or part number) and country of purchase. The system will display the warranty information for your drive.
Yes
www.seagate.com/support/service/
2.5 bels (typical)
2.7 bels (max)
2.9 bels (typical)
3.1 bels (max)
*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment
and formatting.
**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and
power to operational levels.
Barracuda 7200.11 Serial ATA Product Manual, Rev. C 5
Table 2: Drive specifications summary for 640 Gbyte models
Drive specification ST3640323AS ST3640623AS
Formatted capacity (512 bytes/sector)* 640 Gbytes
Guaranteed sectors 1,250,263,728
Heads 4
Discs 2
Bytes per sector 512
Default sectors per track 63
Default read/write heads 16
Default cylinders 16,383
Recording density 1250 kbits/in max
Track density 190 ktracks/in avg
Areal density 219 Gbits/in2 avg
Spindle speed 7,200 RPM
Internal data transfer rate 1460 Mbits/sec max
Sustained data transfer rate OD 115 Mbytes/sec max
I/O data-transfer rate 300 Mbytes/sec max
ATA data-transfer modes supported PIO modes 0–4
Cache buffer 32 Mbytes 16 Mbytes
Height (max) 26.1 mm (1.028 inches)
Width (max) 101.6 mm (4.000 inches) +/- 0.010 inches
Length (max) 146.99 mm (5.787 inches)
Weight (typical) 543 grams (1.199 lb.)
Average latency 4.16 msec
Power-on to ready 20 sec max
Standby to ready 14 sec max
Track-to-track seek time <0.8 msec typical read;
Average seek, read <8.5 msec typical
Average seek, write <10.0 msec typical
Startup current (typical) 12V (peak) 2.8 amps
Voltage tolerance (including noise) 5V +10% / -7.5%
Ambient temperature 0° to 60°C (operating)
Temperature gradient 20°C per hour max (operating)
Relative humidity 5% to 95% (operating)
Relative humidity gradient 30% per hour max
Wet bulb temperature 37.7°C max (operating)
Altitude, operating –60.96 m to 3,048 m
Altitude, nonoperating (below mean sea level, max)
Operational Shock 70 Gs max at 2 msec
Non-Operational Shock 300 Gs max at 2 msec
Multiword DMA modes 0–2 Ultra DMA modes 0–6
<1.0 msec typical write
12V +10% / -7.5%
–40° to 70°C (nonoperating)
30°C per hour max (nonoperating)
5% to 95% (nonoperating)
40.0°C max (nonoperating)
(–200 ft. to 10,000+ ft.)
–60.96 m to 12,192 m (–200 ft. to 40,000+ ft.)
6 Barracuda 7200.11 Serial ATA Product Manual, Rev. C
Drive specification ST3640323AS ST3640623AS
Vibration, operating 2–22 Hz: 0.25 Gs, Limited displacement
Vibration, nonoperating 5–22 Hz: 2.0 Gs
Drive acoustics, sound power
Idle** 2.6 bels (typical)
Performance Seek 3.0 bels (typical)
Quiet Seek 2.7 bels (typical)
Nonrecoverable read errors 1 per 10
Annualized Failure Rate (AFR) 0.34%
Warranty 5 years on distribution units.
Contact start-stop cycles 50,000 at 25°C, 50% rel. humidity
Supports Hotplug operation per the Serial ATA Revision 2.5 specification
22–350 Hz: 0.50 Gs 350–500 Hz:: 0.25 Gs
22–350 Hz: 5.0 Gs 350–500 Hz:: 2.0 Gs
2.8 bels (max)
3.2 bels (max)
2.9 bels (max)
14
bits read
To determine the warranty for a specific drive, use a web browser to access the following web page: From this page, click on the “Verify Your Warranty” link. You will be asked to provide the drive serial number, model number (or part number) and country of purchase. The system will display the warranty information for your drive.
Yes
www.seagate.com/support/service/
*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment
and formatting.
**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and
power to operational levels.
Barracuda 7200.11 Serial ATA Product Manual, Rev. C 7
Table 3: Drive specifications summary for 320 and 160 Gbyte models
Drive specification ST3320613AS ST3320813AS ST3160813AS
Formatted capacity (512 bytes/sector)* 320 Gbytes 160 Gbytes
Guaranteed sectors 625,142,448 312,581,808
Heads 2 1
Discs 1
Bytes per sector 512
Default sectors per track 63
Default read/write heads 16
Default cylinders 16,383
Recording density 1250 kbits/in max
Track density 182 ktracks/in avg
Areal density 219 Gbits/in2 avg
Spindle speed 7,200 RPM
Internal data transfer rate 1460 Mbits/sec max
Sustained data transfer rate OD 115 Mbytes/sec max
I/O data-transfer rate 300 Mbytes/sec max
ATA data-transfer modes supported PIO modes 0–4
Cache buffer 16 Mbytes 8 Mbytes
Height (max) 20.17 mm (0.794 inches)
Width (max) 101.6 mm (4.000 inches) +/- 0.010 inches
Length (max) 146.99 mm (5.787 inches)
Weight (typical) 405 grams ( 0.893 lb.) 390 grams ( 0.860 lb.)
Average latency 4.16 msec
Power-on to ready 9 sec max
Standby to ready 9 sec max
Track-to-track seek time <0.8 msec typical read;
Average seek, read <11.0 msec typical
Average seek, write <12.0 msec typical
Startup current (typical) 12V (peak) 2.0 amps
Voltage tolerance (including noise) 5V +/- 5%
Ambient temperature 0° to 60°C (operating)
Temperature gradient 20°C per hour max (operating)
Relative humidity 5% to 95% (operating)
Relative humidity gradient 30% per hour max
Wet bulb temperature 37.7°C max (operating)
Altitude, operating –60.96 m to 3,048 m
Altitude, nonoperating (below mean sea level, max)
Operational Shock 70 Gs max at 2 msec
Non-Operational Shock 350 Gs max at 2 msec
Multiword DMA modes 0–2 Ultra DMA modes 0–6
<1.0 msec typical write
12V +/-10%
–40° to 70°C (nonoperating)
30°C per hour max (nonoperating)
5% to 95% (nonoperating)
40.0°C max (nonoperating)
(–200 ft. to 10,000+ ft.)
–60.96 m to 12,192 m (–200 ft. to 40,000+ ft.)
8 Barracuda 7200.11 Serial ATA Product Manual, Rev. C
Drive specification ST3320613AS ST3320813AS ST3160813AS
Vibration, operating 2–22 Hz: 0.25 Gs, Limited displacement
Vibration, nonoperating 5–22 Hz: 2.0 Gs
Drive acoustics, sound power
Idle** 2.3 bels (typical)
Performance and Quiet Seek 2.6 bels (typical)
Nonrecoverable read errors 1 per 10
Annualized Failure Rate (AFR) 0.34%
Warranty 5 years on distribution units.
Contact start-stop cycles 50,000 at 25°C, 50% rel. humidity
Supports Hotplug operation per the Serial ATA Revision 2.5 specification
*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment
and formatting.
**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and
power to operational levels.
22–350 Hz: 0.50 Gs 350–500 Hz:: 0.25 Gs
22–350 Hz: 5.0 Gs 350–500 Hz:: 2.0 Gs
2.5 bels (max)
2.8 bels (max)
14
bits read
To determine the warranty for a specific drive, use a web browser to access the following web page: From this page, click on the “Verify Your Warranty” link. You will be asked to provide the drive serial number, model number (or part number) and country of purchase. The system will display the warranty information for your drive.
Yes
www.seagate.com/support/service/
Barracuda 7200.11 Serial ATA Product Manual, Rev. C 9
Loading...
+ 33 hidden pages