Schneider Electric Iconic Installation Instructions

Iconic™ Series

Vertical Grid Horizontal Grid

PIR Motion Sensor

Mechanism

41EPIRM-TN

Installation

Instructions

NOTICE

RISK OF EQUIPMENT DAMAGE OR MALFUNCTION (WIRING CONNECTIONS)

To avoid damaging the equipment and possibly voiding the warranty:

• Test operation during installation and correct any wiring errors immediately.

• Keep cable insulation away from the sides of the enclosure to avoid possible damage or long term degradation of the cable insulation.

Failure to follow these instructions can result in equipment damage or malfunction.

Installation example: hallway

ZONE MASK

SEGMENTS

LOUNGE

HALL

PET

DOOR

ZONE MASK

SEGMENTS

PET

DOOR

Cabling and connections

Single PIR mechanism

LOAD

A Active N Neutral L Load PE Protective Earth

PIR MECHANISM

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• It is illegal for persons other than an appropriately licensed electrical contractors or other persons authorised

by legislation to work on the xed wiring of any electrical

installation.

• To comply with all safety standards, the product must be used only for the purpose described in this instruction and must be installed in accordance with the wiring rules and regulation in the location where it is installed.

• There are no user serviceable parts inside the product.

Failure to follow these instructions will result in death or serious injury.

DANGER

RISK OF ELECTRIC SHOCK

• Hazardous voltage and electrical current may be present at the wire leads of this product even when the device is

switched o󰀨.

• Lock out and tag the input circuit before accessing the wiring connections.

• A circuit breaker (250 V a.c. 10 A) Type C must be installed according to AS/NZS 60898.

• Use a terminal block to connect the PIR Mechanism to the electrical circuit.

• After wiring, wrap the terminal block with insulating tape.

Failure to follow these instructions will result in death or serious injury.

Detection pattern and range

100° Horizontal

Sensor locations

82° Vertical

Max. 5 m @ 20–25 °C

A 1× sensor to cover hallway front entrance. B 1× sensor to cover hallway back entrance. C Zone mask used to prevent detection near the pet door. D Sensor covering lounge area. Zone mask used to prevent

detection in the hallway zone. (See Zone masking.)

Orientation for multi-gang installation

Fitting the PIR mechanism to the grid

2× PIR mechanisms (e.g. hallway application)

LOAD

PIR MECHANISM PIR MECHANISM

A Active N Neutral L Load PE Protective Earth

Securing the PIR mechanism fly leads

Note: Ensure that the PIR mechanism y leads are tied back

or otherwise secured in accordance with the wiring rules and regulations that apply in the location where the mechanism is installed.

Mounting the grid

Wall box depth:

min. 41 mm

CAUTION

EQUIPMENT DAMAGE HAZARD

• Install the device according to instructions in this document.

• Pay attention to the specications and wiring diagrams related to the installation.

• Do not use this product for any other purpose than

specied in this instruction.

Failure to follow these instructions can result in minor injuries, or equipment damage.

1 Open the locking bar A. 2 Push the head of the PIR mechanism into the grid aperture

until the head clicks into place B.

3 Close the locking bar C.

Adjusting the timer and lux settings

min. 2 lx

Timer

Lux

(Approx.

10 mins)

max.

15 mins

max.

2000 lx

min. 10 secs

Zone masking

Masked

zone

50°

1 Remove zone mask segments to allow sensor to detect

movement A.

2 Remaining segments prevent detection of movement B.

Fitting the carrier or zone mask to the skin

Installing the skin Removing the skin

Manual override options

Depending on the wiring and the type of switch used, the following manual override options are possible:

Option 1: Manual override activated by the sensor using a

rocker switch.

Option 2: Manual override bypassing the sensor using a

rocker switch.

Option 3: Manual override with 3-position switch.

Choose a manual override option to suit the desired operation.

Desired operation 1 2 3

Switch load On when movement detected. Yes Yes Yes

Switch load O󰀨 when no movement detected and sensor timer has expired.

Manually switch load O󰀨 indenitely until

manual switch back to sensor operation.

Manually switch load On indenitely until

manual switch back to sensor operation.

Manually switch sensor O󰀨 indenitely until manual switch back to sensor operation.

Manually switch load O󰀨 on exit, then sensor

resumes normal operation automatically.

Manually switch load On when entering room (e.g. if sensor hasn’t detected movement) then sensor resumes normal operation automatically.

Manual override

option

Yes Yes Yes

Yes No Yes

No Yes Yes

Yes No Yes

Manual override option 1

Add a 1/2 way switch.

Sensor-activated override

• Toggle the switch to position B and back to A within 1.5 seconds.

• Sensor toggles the load state On or O󰀨 and maintains that state for the duration of the sensor timer setting.

• Sensor resumes normal operation once timer expires.

Note: If power to sensor is interrupted for 1.5 seconds, the load is switched on for about 1 minute, then sensor resumes normal operation.

Manual OFF

• Operate switch to position B (turns sensor and load O󰀨).

• Operate switch to position A to resume sensor operation.

Cabling and connections for option 1

A Active N Neutral L Load PE Protective Earth

Optional 2nd sensor + switch (e.g. hallway application)

PIR MECHANISM

SWITCH (1/2 WAY)

LOAD

PIR MECHANISM

SWITCH (1/2 WAY)

Manual override option 2

Add a 1/2 way switch. Labelled dolly recommended (“Auto/Manual” shown).

Auto

Manual

Manual ON

• Operate switch to position B to override sensor and keep load On.

• Operate switch to position A for normal sensor operation.

Cabling and connections for option 2

A Active N Neutral L Load PE Protective Earth

Optional 2nd sensor + switch (e.g. hallway application)

PIR MECHANISM

SWITCH (1/2 WAY)

LOAD

SWITCH (1/2 WAY)

PIR MECHANISM

Manual override option 3

Add a 3-position switch.

Labelled dolly recommended

(“Sensor/O󰀨/On” shown).

Manual OFF

• Operate switch to position B (turns sensor and load O󰀨).

• Operate switch to position A to resume sensor operation.

Manual ON

• Operate switch to position c to override sensor and keep load On.

• Operate switch to position A for normal sensor operation.

Cabling and connections for option 3

A Active N Neutral L Load PE Protective Earth

Optional 2nd sensor + switch (e.g. hallway application)

PIR MECHANISM

SWITCH (3-POS)

Sensor

Off On

PIR MECHANISM

SWITCH (3-POS)

Technical specifications

Operating voltage 220–240 V a.c., 50 Hz

Auto

Manual

Sensor

Off On

LOAD

Load ratings Incandescent lamps: 750 W

Fluorescent lamps: 100 W

LED lamps: 150 W

(max. 4 lamps)

Motor: M.3

AC halogen lamps: 400 W

LV halogen lamps: 400 VA

Timer setting range min. 10 s, max. 15 mins

Lux setting range min. 2 lx, max. 2000 lx

Detection technology Passive Infrared (PIR)

Angle of coverage 100° horizontal, 82° vertical

Detection range max. 5 m (at 20–25 °C)

Environmental rating IP20 (for indoor use only)

Operating temperature –10 °C to 50 °C

Compliance AS/NZS 60669-2-1

Specications typical at 25 °C.

49 mm

48.5 mm

Customer care

A B

Warranty information

We warrant this product for 2 years. For details, please visit http://www. schneider-electric.com.au/en/about-us/legal/terms-and-conditions.jsp.

Our goods also come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Schneider Electric (Australia) Pty Ltd

Customer Care Australia: 1300 369 233

Email: customercare.au@schneider-electric.com

www.schneider-electric.com.au

Schneider Electric reserves the right to change specications, modify designs and discontinue items without incurring obligation and whilst every e󰀨ort is made to ensure that descriptions, specications and other information in this catalogue are correct, no warranty is given in respect thereof and the company shall not be liable for any error therein.

This material is copyright under Australian and international laws. Except as permitted under the relevant law, no part of this work may be reproduced by any process without prior written permission of and acknowledgement to Schneider Electric.

F2842

23.5 mm

October 2017