Sanyo PLC-XT11, PLC-XT16 User Manual

Multimedia Projector

MODEL PLC-XT11 PLC-XT16

Owner’s Manual

TO THE OWNER

Before operating this projector, read this manual thoroughly and operate the projector properly.

This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time.

Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents.

If your projector seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the “TROUBLESHOOTING” section at the end of this booklet. If the problem still persists, contact the sales dealer where you purchased the projector or the service center.

SAFETY PRECAUTIONS

WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

●This projector produces intense light from the projection lens. Do not stare directly into the lens as possible. Eye damage could result. Be especially careful that children do not stare directly into the beam.

●Do not use projectors with whiteboards that produce a very bright glare or 'hot spot'. This seems to happen most on shiny surfaces.

●This projector should be set in the way indicated. If not, it may result in a fire hazard.

● Take appropriate space on the top, sides and rear of the projector				SIDE and TOP				REAR
cabinet for allowing air circulation and cooling the projector. 20cm
Minimum distance should be taken. If the projector is to be built
into a compartment or similarly enclosed, the minimum distances
must be maintained. Do not cover the ventilation slot on the
projector. Heat build-up can reduce the service life of your				50cm		50cm			50cm
projector, and can also be dangerous.

●Do not put any flammable object or spray can near the projector, hot air is exhausted from the ventilation holes.

●Remote Control Unit, supplied to this projector, emits the laser beam as the laser pointer function from Laser Light Window while pressing LASER button (for 1 minute / LASER POINTER INDICATOR lights red to indicate laser emission). Do not look into Laser Light Window or shine the laser beam on yourself or other people. Eye damage may result.

●If the projector is not to be used for an extended time, unplug the projector from the power outlet.

READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE OWNER'S MANUAL WITH THIS UNIT.

2

SAFETY INSTRUCTIONS

All the safety and operating instructions should be read before the product is operated.

Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

Follow all warnings and instructions marked on the projector.

For added protection to the projector during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage due to lightning and power line surges.

Do not expose this unit to rain or use near water... for

example, in a wet basement, near a swimming pool, etc...

Do not use attachments not recommended by the manufacturer as they may cause hazards.

Do not place this projector on an unstable cart, stand, or table. The projector may fall, causing serious injury to a child or adult, and serious damage to the projector. Use only with a cart or stand recommended by the manufacturer, or sold with the projector. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the manufacturers.

An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

Slots and openings in the back and bottom of the cabinet are provided for ventilation, to insure reliable operation of the equipment and to protect it from overheating.

The openings should never be covered with cloth or other materials, and the bottom opening should not be blocked by placing the projector on a bed, sofa, rug, or other similar surface. This projector should never be placed near or over a radiator or heat register.

This projector should not be placed in a built-in installation such as a book case unless proper ventilation is provided.

Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the projector.

This projector should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied, consult your authorized dealer or local power company.

Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on the power cord. Do not locate this projector where the cord may be damaged by persons walking on it.

Do not attempt to service this projector yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

Unplug this projector from wall outlet and refer servicing to qualified service personnel under the following conditions:

a.When the power cord or plug is damaged or frayed.

b.If liquid has been spilled into the projector.

c.If the projector has been exposed to rain or water.

d.If the projector does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the projector to normal operation.

e.If the projector has been dropped or the cabinet has been damaged.

f.When the projector exhibits a distinct change in performance-this indicates a need for service.

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or injury to persons.

Upon completion of any service or repairs to this projector, ask the service technician to perform routine safety checks to determine that the projector is in safe operating condition.

Voor de klanten in Nederland

Bij dit product zijn batterijen geleverd.

Wanneer deze leeg zijn, moet u ze niet weggooien maar inleveren als KCA.

3

COMPLIANCES

Federal Communication Commission Notice

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures :

–Reorient or relocate the receiving antenna.

–Increase the separation between the equipment and receiver.

–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

–Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.

Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment.

Model Numbers	: PLC-XT11, PLC-XT16
Trade Name	: Sanyo
Responsible party	: SANYO FISHER COMPANY
Address	: 21605 Plummer Street, Chatsworth, California 91311
Telephone No.	: [phone]

AC POWER CORD REQUIREMENT

The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.

AC Power Cord for the United States and Canada :

AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and certified by the Canadian Standard Association (CSA).

AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be

unable to insert the plug into the outlet, contact your electrician.	GROUND

AC Power Cord for the United Kingdom :

This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug. Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the same rating, marked thus ASA . If the fuse cover is detachable, never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of the plug (i.e. red or orange). Fuse covers are available from the Parts Department indicated in your User Instructions.

If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed. The end of the flexible cord should be suitably prepared and the correct plug fitted. (See Over)

WARNING : A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED IN A LIVE SOCKET OUTLET.

The Wires in this mains lead are coloured in accordance with the following code: Green-and-yellow ············ Earth

Blue ································· Neutral Brown ······························ Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:

The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured green or green-and-yellow.

The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

WARNING : THIS APPARATUS MUST BE EARTHED.

THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.

4

TABLE OF CONTENTS

	FEATURES AND DESIGN	6	COMPUTER INPUT	22
			SELECTING INPUT SOURCE	22
	PREPARATION	7	SELECTING COMPUTER SYSTEM	23
			COMPATIBLE COMPUTER SPECIFICATIONS	24
	NAME OF EACH PART OF PROJECTOR	7	PC ADJUSTMENT	25
			AUTO PC ADJUSTMENT	25
	SETTING-UP PROJECTOR	8	MANUAL PC ADJUSTMENT	26
	CONNECTING AC POWER CORD	8	PICTURE IMAGE ADJUSTMENTS	28
	POSITIONING PROJECTOR	9	IMAGE LEVEL SELECT	28
	ADJUSTABLE FEET	10	IMAGE LEVEL ADJUSTMENT	29
	MOVING PROJECTOR	10	PICTURE SCREEN ADJUSTMENT	30
	CONNECTING PROJECTOR	11	VIDEO INPUT	31
	TERMINALS OF PROJECTOR	11	SELECTING INPUT SOURCE	31
	CONNECTING TO COMPUTER	12	SELECTING VIDEO SYSTEM	32
	CONNECTING TO VIDEO EQUIPMENT	13	PICTURE IMAGE ADJUSTMENTS	33
			IMAGE LEVEL SELECT	33
			IMAGE LEVEL ADJUSTMENT	34
	BEFORE OPERATION	14	PICTURE SCREEN ADJUSTMENT	35
	OPERATION OF REMOTE CONTROL UNIT	14	SETTING	36
	LASER POINTER FUNCTION	14
	REMOTE CONTROL BATTERIES INSTALLATION	15	SETTING MENU	36
	TOP CONTROLS AND INDICATORS	16
	OPERATING ON-SCREEN MENU	17
	HOW TO OPERATE ON-SCREEN MENU	17	APPENDIX	38
	FLOW OF ON-SCREEN MENU OPERATION	17
	MENU BAR	18
			LAMP REPLACEMENT	38
	BASIC OPERATION	19
	TURNING ON / OFF PROJECTOR	19	MAINTENANCE	41
	ADJUSTING SCREEN	20	WARNING TEMP. INDICATOR	41
	ZOOM ADJUSTMENT	20	AIR FILTER CARE AND CLEANING	41
			CLEANING PROJECTION LENS	41
	FOCUS ADJUSTMENT	20
			TROUBLESHOOTING	42
	LENS SHIFT ADJUSTMENT	20
	KEYSTONE ADJUSTMENT	20	TECHNICAL SPECIFICATIONS	44
	PICTURE FREEZE FUNCTION	21	CONFIGURATIONS OF TERMINALS	45
	NO SHOW FUNCTION	21	OPTIONAL PARTS	46
	P-TIMER FUNCTION	21	INDICATOR AND PROJECTOR CONDITION	47
	SOUND ADJUSTMENT	21

TRADEMARKS

●Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.

●IBM, VGA, XGA, and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.

●Windows and PowerPoint are registered trademarks of Microsoft Corporation.

●Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its respective corporation.

5

FEATURES AND DESIGN

This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of use. This projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology.

Compact Design

This projector is extremely compact in size and weight. It is designed to carry and work anywhere you wish to use.

Compatibility

This projector widely accepts various video and computer input signals including;

●Computers

IBM-compatible or Macintosh computer up to 1280 x 1024 resolution.

●6 Color Systems

NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PAL- N color system can be connected.

●Component Video

Component video signal, such as a DVD player output high definition TV signals including 480i, 480p, 575i, 575p, 720p, 1035i or 1080i, can be connected.

●S-Video

S-Video signal, such as a S-VHS VCR output signal, can be connected.

High Resolution Image

This projector provides 1024 x 768 dots resolution for computer input and 800 horizontal TV lines. Resolution from a computer between XGA (1024 x 768) and SXGA (1280 x 1024) is compressed into 1024 x 768 dots. This projector cannot display image of over 1280 x 1024 dots. When resolution of your computer is over than 1280 x 1024, reset a computer output for lower resolution.

Keystone Correction

Positioning of a projector may result in distorted image being displayed in a trapezoid shape. Keystone Correction solves this problem by digitally altering projection to produce undistorted images.

Power Management

Power Management function is provided to reduce power consumption while a projector is not in use.

This Power Management function operates to turn Projection Lamp off when a projector detects signal interruption and any button is not pressed over 5 minutes. Projection Lamp is automatically turned on again when a projector detects signal or any operation button is pressed.

This projector is shipped with this function ON.

Digital Visual Interface

This projector is equipped with DVI 29-pin terminal for connecting DVI output from a computer.

Laser Pointer Function

Remote Control Unit supplied with this projector includes Laser Pointer function. This function helps you to make a smart presentation on a projected screen.

Wireless Mouse

Remote Control Unit supplied with this projector has Wireless Mouse function for a connected computer. This function enables you to operate both projector and computer with Remote Control Unit only.

Multi-Scan System

Multilanguage Menu Display

This projector has Multi-Scan System to conform to almost all computer output signals quickly. There is no need for troublesome manual adjustment of frequency and other settings.

Operation menu is displayed in; English, German, French, Italian, Spanish, Portuguese, Dutch, Swedish, Russian, Chinese, Korean or Japanese.

Progressive Scan Function

This function converts interlace video signals into progressive scan signals and provide fine picture quality.

One-Touch Auto PC Adjustment

Incoming computer video signals are recognized and the best adjustment is automatically set by Auto PC Adjustment. No complicated setup is necessary and projection is always precise.

Digital Zoom (for Computer)

Digital Zoom function adjusts the image size to approx. 1/4 ~ 49 times of original image size, allowing you to focus on crucial information at a presentation.

Motor-driven Lens Shift

Projection lens can be moved up and down with motordriven lens shift function. This function makes it easy to provide projected image where you want.

Zoom and focus can be also adjusted with motor-driven operation.

Media Card Imager (Optional)

Optional Media Card Imager is available for this projector. For the Media Card Imager, contact the sales dealer where you purchased this projector.

Wireless Imager (Optional)

This projector can be operated through Wireless LAN by attaching Wireless imager that is optionally supplied. For the Wireless Imager, contact the sales dealer where you purchased the projector.

PJ-Net Organizer (Optional)

PJ-Net Organizer is an optional product to control and set up a projector via the network cable. By accessing to the connected projector using the web browser on your computer. It can be controlled and set up the projector remotely. Contact the sales dealer where you purchased this projector for optional parts.

6

PREPARATION

NAME OF EACH PART OF PROJECTOR

FRONT

TOP CONTROLS

AND INDICATORS

INFRARED

REMOTE RECEIVER

PROJECTION LENS

LENS COVER

BACK TERMINALS

AND CONNECTORS

EXHAUST VENTS

HOT AIR EXHAUSTED !

Air blown from Exhaust Vents is hot. When using or installing projector, following precautions should be taken.

●Do not put any flammable object near this vent.

●Keep side grill at least 3’(1m) away from

any object, especially heat-sensitive object.

● Do not touch this area, especially screw and metallic part. This area will become hot while a projector is used.

This projector detects internal temperature and automatically controls operating power of Cooling Fans.

SPEAKERS
AIR INTAKE VENT
INFRARED	AIR INTAKE VENT

REMOTE RECEIVER

CARRY HANDLE

POWER CORD CONNECTOR

BOTTOM

AIR INTAKE VENTS

This projector is equipped with Cooling Fans for protection from overheating. Pay attention to the following to ensure proper ventilation and avoid a possible

risk of fire and malfunction.

●Do not cover vent slots.

●Keep side and bottom clear of any

object. Obstructions may block cooling air.

ADJUSTABLE FEET

AND

FEET LOCK LATCHES

LAMP COVER

AIR FILTERS

7

PREPARATION

SETTING-UP PROJECTOR

CONNECTING AC POWER CORD

This projector uses nominal input voltages of 100-120 V or 200-240 V AC. This projector automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce risk of electrical shock, do not plug into any other type of power system.

Consult your authorized dealer or service station if you are not sure of the type of power supply being in use.

Connect a projector with a peripheral equipment before turning a projector on. (Refer to pages 11 ~ 13 for connection.)

CAUTION

For safety, unplug AC Power Cord when an appliance is not used.

When this projector is connected to the outlet with AC Power Cord, an appliance is in Stand-by Mode and consumes a little electric power.

Connect AC Power Cord (supplied) to a projector. The AC outlet must be near this equipment and must be easily accessible.

NOTE ON THE POWER CORD

AC Power Cord must meet requirement of the country where you use a projector.

Confirm an AC plug type with the chart below and proper AC Power Cord must be used.

If supplied AC Power Cord does not match your AC outlet, contact your sales dealer.

Projector side						AC Outlet side
		For the U.S.A. and Canada				For Continental Europe		For the U.K.
			Ground

To POWER CORD						To the AC Outlet.
		To the AC Outlet.
CONNECTOR on your				To the AC Outlet.		(200 - 240 V AC)
		(120 V AC)
projector.				(200 - 240 V AC)

8

PREPARATION

POSITIONING PROJECTOR

●This projector is designed to project on a flat projection surface.

●Projector can be focused from 4.1’ (1.2m) ~ 32.8’ (10.0m).

●Refer to figure below to adjust screen size.

ROOM LIGHT

Brightness in room has a great influence on picture quality. It is recommended to limit ambient lighting in order to provide best image.

32.8’(10.0m)

						22.0’(6.7m)					300”
										Max. Zoom
					16.4’(5.0m)
						200”
		10.8’(3.3m)									231”
					150”
4.1’(1.2m)
										Min. Zoom
			100”			154”

115”

39” 77”

30”

Screen

Max. Zoom

39”

100”

150”

200”

250”

300”

Size

Min. Zoom

30”

77”

115”

154”

192”

231”

Distance

4.1’ (1.2m)

10.8’ (3.3m)

16.4’ (5.0m)

22.0’ (6.7m)

27.6’ (8.4m)

32.8’ (10.0m)

LENS SHIFT ADJUSTMENT

Projection lens can be moved up and down with motor-driven lens shift function. This function makes it easy to provide projected image where you want. U/D ratio can be adjusted 10 : 0 ~ 1 : 1 (refer to figure below.). Refer to P 20 for operation.

Highest (10 : 0) Lowest (1 : 1)

1

10 : 0

1

9

PREPARATION

ADJUSTABLE FEET

Picture tilt and projection angle can be adjusted by rotating ADJUSTABLE FEET. Projection angle can be adjusted to 10 degrees.

1	Lift the front of a projector and pull FEET LOCK LATCHES
	on the both sides of a projector.
2	Release FEET LOCK LATCHES to lock ADJUSTABLE FEET
	and rotate ADJUSTABLE FEET to fine tune position and tilt.
3	To retract ADJUSTABLE FEET, lift the front of a projector
	and pull and undo FEET LOCK LATCHES.

Keystone distortion of a projected image can be adjusted by Menu Operation. (Refer to P20 and 36.)

NOTE :

THIS PROJECTOR SHOULD BE SET IN THE WAY INDICATED. PROJECTION LAMP MAY MALFUNCTION.

	FEET LOCK
ADJUSTABLE FEET	LATCHES

MOVING PROJECTOR

Use Carry Handle when moving a projector.

When moving a projector, replace Lens Cover and retract Adjustable Feet to prevent damage to the lens and cabinet.

When a projector is not in use for an extended period, put it into the case (dust cover) supplied with a projector.

CAUTION

Dust Cover (supplied) is intended for protection from dust and scratches on the surface of a cabinet, and it is not designed to protect an appliance from external forces. Do not transport a projector through a courier or transport services with this cover. The projector can be damaged. When handling a projector, do not drop, bump, subject it to strong forces or put other things on the cabinet.

CAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR

●Do not drop or bump a projector, otherwise damages or malfunctions may result.

●When carrying a projector, use a suitable carrying case.

●Do not transport a projector by using a courier or transport service in an unsuitable transport case. This may cause damage to a projector. To transport a projector through a courier or transport service, consult your dealer for best way.

10

CONNECTING PROJECTOR

TERMINALS OF PROJECTOR

This projector has input and output terminals on its back for connecting computers and video equipment. Refer to figures on pages 11 to 13 and connect properly.

COMPUTER INPUT 2 (DIGITAL/ANALOG)

Media Card Imager / Wireless Imager

/PJ-Net Organizer TERMINAL

Connect computer output (Digital / Analog DVI-I type),

Media Card Imager*, Wireless Imager* or PJ-Net Organizer* to this terminal. (Refer to P12)

*optional accessories

MONITOR OUTPUT		COMPUTER INPUT 1		COMPUTER AUDIO
TERMINAL		TERMINAL		INPUT (1 and 2) JACKS
Connect a monitor to		Connect computer output		Connect an audio output
this terminal.		(Analog HDB 15-pin type) or		(stereo) from computer to
This terminal outputs a		21-pin Scart (RGB) output		these jacks.
computer input signal		from video equipment to this		(Refer to P12.)
(except Digital signal		terminal. (Refer to P12, 13.)
input on DVI terminal).
(Refer to P12.)

COMPUTER IN 1

AUDIO IN 1

COMPUTER IN 2

DVI - I

RESET

AUDIO IN 2

AUDIO OUTPUT JACK			CONTROL PORT
Connect	an external	AUDIO OUT
		MONITOR OUT
audio amplifier to this
			S – VIDEO
jack.		R – AUDIO IN – L (MONO) VIDEO
(Refer to P12, 13.)		MCI / WI
		Y – Pb / Cb – Pr / Cr	USB

Do not press this button. This button is used for our optional accessories.

RESET BUTTON

This projector uses a micro processor to control this unit, and occasionally, this micro processor may malfunction and need to be reset. This can be done by pressing RESET button with a pen, which will shut down and restart the unit. Do not use RESET function excessively.

CONTROL PORT CONNECTOR

When controlling the computer with Remote Control Unit of this projector, connect the mouse port of your personal computer to this connector. (Refer to P12.)

S-VIDEO INPUT JACK

Connect the S-VIDEO output from video equipment to this jack. (Refer to P13.)

AUDIO INPUT JACKS

Connect the audio output from video equipment to these jacks.

(Refer to P13.)

When the audio output is monaural, connect it to L (MONO) jack.

VIDEO INPUT JACKS			VIDEO INPUT JACK		USB CONNECTOR (Series B)
Connect the	component		Connect the composite		When controlling the computer
video output	from video		video output from video		with Remote Control Unit of this
equipment to connect the			equipment to connect		projector, connect USB port of
component video outputs to			this jack.		your personal computer to this
Y, Pb/Cb and Pr/Cr jacks.			(Refer to P13.)		connector. (Refer to P12.)
(Refer to P13.)

11

CONNECTING PROJECTOR

CONNECTING TO COMPUTER

Cables used for connection ( = Cable or adapter is not supplied with this projector.)

• VGA Cable (HDB 15 pin)	• USB Cable
• Control Cable for SERIAL Port	• MAC Adapter (When connecting to Macintosh computer)
• DVI-Digital Cable (for Single Link T.M.D.S.)	• DVI/VGA Adapter
• Control Cable for PS2 Port , or ADB Port	• Audio Cables {Mini Plug (stereo) x 2}

IBM-compatible computer or Macintosh computer (VGA / SVGA / XGA / SXGA)

Desktop type	Laptop type
Monitor Output Monitor Input Audio Output USB port Serial port	PS/2 port ADB port

MAC Adapter
Set slide switches
according to the					Control Cable	Control Cable
chart below.		Audio		Control Cable
	VGA		USB	for Serial Port	for PS/2 Port	for ADB Port
		Cable
DVI Cable
	Cable	(stereo)	Cable	Terminal	Terminal	Terminal

VGA Cable

COMPUTER IN 2 DVI-I

MONITOR OUT

COMPUTER

USB

AUDIO IN

Use one of these Control

COMPUTER IN 1

Cables corresponding with

DVI/VGA

COMPUTER IN 1

the terminal of your

Adapter

computer.

COMPUTER IN 2

AUDIO IN 1

DVI - I

AUDIO IN 2

RESET

CONTROL PORT

CONTROL PORT

COMPUTER IN 2 DVI-I

AUDIO OUT

MONITOR OUT

R – AUDIO IN – L (MONO) VIDEO

S – VIDEO

MCI / WI

Y

–

Pb / Cb – Pr / Cr

USB

Terminals

of the Projector

AUDIO OUT

NOTE :

When connecting the cable, the power

cords of both the projector and the external

equipment should be disconnected from

Audio Cable

AC outlet.

Turn

the projector

and

peripheral equipment on before the

(stereo)

computer is switched on.

MAC ADAPTER (Not supplied)

Set switches as shown in the table ON

below depending on RESOLU-

ON

DIP

Audio Input

TION MODE that you want to use

1

2

3

4

5

6

before you turn on projector and

OFF

External Audio Equipment

computer.

Audio Speaker

1

2

3

4

5

6

Audio Amplifier

13" MODE (640 x 480)

ON

ON

OFF

OFF

OFF

OFF

(stereo)

16" MODE (832 x 624)

OFF

ON

OFF

ON

OFF

OFF

19" MODE (1024 x 768)

OFF

ON

ON

OFF

OFF

OFF

21" MODE (1152 x 870)

ON

ON

ON

ON

OFF

OFF

12

CONNECTING PROJECTOR

CONNECTING TO VIDEO EQUIPMENT

Cables used for connection ( = Cable is not supplied with this projector.)

• Video Cable (RCA x 1 or RCA x 3)

• Audio Cable {Mini Plug (stereo)}

• S-VIDEO Cable

• Scart Cable

• Audio Cable (RCA x 2)

Video Source (example)

Component video output equipment.

Video Cassette Recorder

Video Disc Player

(such as DVD player or high-definition TV source.)

RGB Scart

Audio Output

Composite

S-VIDEO Output

Component Video Output

21-pin Output

(R, L)

Video Output

(Y, Pb/Cb, Pr/Cr)

		Audio Cable	Video Cable	S-VIDEO	Video Cable
	Scart Cable				(RCA x 3)
		(RCA x 2)	(RCA x 1)	Cable

	AUDIO IN	VIDEO	S-VIDEO	Y - Pb/Cb - Pr/Cr
		COMPUTER IN 1
		AUDIO IN 1
	COMPUTER IN 2
COMPUTER IN 1	DVI - I
		AUDIO IN 2	RESET
			CONTROL PORT
		AUDIO OUT
		MONITOR OUT
	R – AUDIO IN – L (MONO) VIDEO		S – VIDEO
Use any of VIDEO jack, S-VIDEO	MCI / WI
jack, or Y-Pb/Cb-Pr/Cr jacks.	Y	– Pb / Cb – Pr / Cr	USB
• When both VIDEO jack and S-
VIDEO jack are connected, S-
VIDEO jack has priority over				Terminals
VIDEO jack.
				of the Projector
• When both Y-Pb/Cb-Pr/Cr jacks
and S-VIDEO jack are connected,
Y-Pb/Cb-Pr/Cr jacks has priority
over S-VIDEO jack.

AUDIO OUT

Audio Cable (Stereo)

Audio Input

NOTE :

External Audio Equipment

When connecting the cable, the power

Audio Speaker

cords of both the projector and the external

Audio Amplifier

(stereo)

equipment should be disconnected from

AC outlet.

13

BEFORE OPERATION

OPERATION OF REMOTE CONTROL

Left Side

ON

OFF ALL

ALL-OFF SWITCH

When using Remote Control Unit, turn this switch to “ON.” And turn it to “ALL OFF” when it is not used.

INSIDE THE BATTERY COMPARTMENT BOX

This remote control provide the DIP switches into the battery compartment box.

Slide the SW4 (LASER ON/OFF switch) to "OFF" position. The laser pointer function is not operated.

Set switches 1-3 as shown in table below depending on Code No. that you want to select remote control code.

(Refer to P37.)

DIP SWITCH SETTING

							SW4 ........ LASER ON/OFF
							SW1	SW2	SW3	Code No.
				4			ON	ON	ON	Code 1
ON				3			ON	ON	OFF	Code 2
				2			ON	OFF	ON	Code 3
							ON	OFF	OFF	Code 4
				1
							OFF	ON	ON	Code 5
							OFF	ON	OFF	Code 6
							OFF	OFF	ON	Code 7
							OFF	OFF	OFF	Code 8

LASER POINTER (Drag ON)

INDICATOR

Lights red while laser beam is emitted from Laser Light Window.

Lights green when drag ON position. (P40)

MUTE BUTTON

Used to mute sound. (P21)

DRAG ON/OFF BUTTON

Used to select drag ON/OFF position. (P40)

LEFT CLICK BUTTON

Used as a PC mouse in Wireless Mouse Operation. Press this button and the mouse pointer button to drag a selected screen object. (P40)

LASER BUTTON

Used to operate Laser Pointer Function. Laser beam is emitted while pressing this button within 1 minute.

When using this Laser Pointer for more than 1 minute, release LASER button and press it again.

FOCUS BUTTON

Used to adjust focus. (P20)

			AUTO PC ON-OFF
		D.ZOOM FREEZE NO SHOW
	LOCK	MUTE	IMAGE
		VOLUME-	SELECT VOLUME+
		MENU	KEYSTONE

LASER

P-TIMERCOMPUTER 1

ZOOM	COMPUTER 2

VIDEO

FOCUS LENS

POWER ON-OFF BUTTON

Used to turn projector on or off. (P19)

AUTO PC ADJ. BUTTON

Use to operate AUTO PC Adjustment function. (P25)

IMAGE BUTTON

Used to select image level. (P28, 33)

KEYSTONE BUTTON

Used to correct keystone distortion. (P20, 36)

MOUSE POINTER

Used as a PC mouse in Wireless Mouse Operation. (P40)

RIGHT CLICK BUTTON

Used as a PC mouse in Wireless Mouse Operation. (P40)

LENS SHIFT BUTTON

Used to select LENS SHIFT function. (P20)

LASER POINTER FUNCTION

This Remote Control Unit emits a laser beam as laser pointer function from Laser Light Window. When LASER button is pressed, laser light goes on. And when LASER button is being pressed for more than 1 minute or LASER button is released, light goes off. LASER POINTER INDICATOR lights RED and Laser is emitted with RED light to indicate laser beam is being emitted.

Laser emitted is a class II laser; therefore, do not look into Laser Light Window or shine laser beam on yourself or other people. Three marks below are caution labels for laser beam.

CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result hazardous radiation exposure.

These caution labels are put on remote control.

LASER POINTER INDICATOR

Laser Light Window

14

BEFORE OPERATION

D.ZOOM BUTTON

Used to select DIGITAL ZOOM +/– mode and resize image. (P30)

SELECT BUTTON

Used to execute item selected, or to expand or compress image in DIGITAL ZOOM +/- mode. (P30)

MENU BUTTON

Used to select MENU operation. (P17, 18)

P-TIMER BUTTON

Used to operate P- TIMER function. (P21)

ZOOM BUTTON

Used to adjust zoom. (P20)

			AUTO PC ON-OFF
		D.ZOOM FREEZE NO SHOW
	LOCK	MUTE	IMAGE
		VOLUME-	SELECT VOLUME+
		MENU	KEYSTONE

LASER

P-TIMERCOMPUTER 1

ZOOM	COMPUTER 2

VIDEO

FOCUS LENS

NO SHOW BUTTON

Used to turn picture into black image. (P21)

FREEZE BUTTON

Used to freeze picture. (P21)

POINT (VOLUME +/-)

BUTTONS

Used to select an item or adjust value in ON-SCREEN MENU. They are also used to pan image in DIGITAL ZOOM +/- mode. (P30)

POINT LEFT/RIGHT buttons are also used as VOLUME +/- buttons. (P21)

COMPUTER 1 BUTTON

Used to select input source (COMPUTER 1). (P22)

COMPUTER 2 BUTTON

Used to select input source (COMPUTER 2). (P22, 31)

VIDEO BUTTON

Used to select input source (VIDEO). (P31)

Operating Range

Point Remote Control Unit toward projector (Receiver Window) whenever pressing any button. Maximum operating range for Remote Control Unit is about 16.4’ (5m) and 60° in front and rear of a projector.

60°

16.4’ (5 m)

16.4’

(5 m)

60°

Remote Control Batteries Installation

1

2

Press lid downward and slide it.

Two AA size batteries

For correct polarity (+ and

–), be sure battery terminals are in contact with pins in compartment.

To insure safe operation, please observe following precautions :

●Use (2) AA, UM3 or R06 type alkaline batteries.

●Replace two batteries at same time.

●Do not use a new battery with an used battery.

●Avoid contact with water or liquid.

●Do not expose Remote Control Unit to moisture, or heat.

●Do not drop Remote Control Unit.

●If a battery has leaked on Remote Control Unit, carefully wipe case clean and install new batteries.

●Danger of explosion if battery is incorrectly replaced.

●Dispose of used batteries according to batteries manufacturers instructions and local rules.

15