Sanyo PLC-XP51L, PLC-XP51, PLC-XP50 User Manual

0 (0)

Multimedia Projector

MODEL PLC-XP50/XP51

PLC-XP50L/XP51L (Lensless)

Owner’s Manual

TO THE OWNER

Before operating this projector, read this manual thoroughly and operate the projector properly.

This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time.

Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents.

If your projector seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the “Trouble-shooting” section of the end of this booklet. If the problem still persists, contact the sales dealer where you purchased the projector or the service center.

SAFETY PRECAUTIONS

WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

This projector produces intense light from the projection lens. Do not stare directly into the lens as possible. Eye damage could result. Be especially careful that children do not stare directly into the beam.

This projector should be set in the way indicated. If not, it may result in a fire hazard.

● Take appropriate space on the top, sides and rear of the projector

 

SIDE and TOP

 

REAR

 

cabinet for allowing air circulation and cooling the projector. 20cm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Minimum distance should be taken. If the projector is to be built

 

 

 

 

 

 

 

 

 

 

into a compartment or similarly enclosed, the minimum distances

 

 

 

 

 

 

 

 

must be maintained. Do not cover the ventilation slot on the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

projector. Heat build-up can reduce the service life of your

 

50cm

 

50cm

 

 

50cm

 

 

 

 

 

 

projector, and can also be dangerous.

 

 

 

 

 

 

 

 

Do not put any flammable object or spray can near the projector, hot air is exhausted from the ventilation holes.

Remote Control Unit, supplied to this projector, emits the laser beam as the laser pointer function from Laser Light Window while pressing LASER button (for 1 minute / LASER POINTER INDICATOR lights red to indicate laser emission). Do not look into Laser Light Window or shine the laser beam on yourself or other people. Eye damage may result.

If the projector is not to be used for an extended time, unplug the projector from the power outlet.

READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.

CAUTION

Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/Data Processing Equipment, ANSI/NFPA 75.

Ne puet être utillisé dans une salle d’ordinateurs telle que définie dans la norme ANSI/NFPA 75 Standard for Protection of Electronic Computer/Data Processing Equipment

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE OWNER'S MANUAL WITH THIS UNIT.

2

SAFETY INSTRUCTIONS

All the safety and operating instructions should be read before the product is operated.

Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

Follow all warnings and instructions marked on the projector.

For added protection to the projector during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage due to lightning and power line surges.

Do not expose this unit to rain or use near water... for

example, in a wet basement, near a swimming pool, etc...

Do not use attachments not recommended by the manufacturer as they may cause hazards.

Do not place this projector on an unstable cart, stand, or table. The projector may fall, causing serious injury to a child or adult, and serious damage to the projector. Use only with a cart or stand recommended by the manufacturer, or sold with the projector. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the manufacturers.

An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

Slots and openings in the back and bottom of the cabinet are provided for ventilation, to insure reliable operation of the equipment and to protect it from overheating.

The openings should never be covered with cloth or other materials, and the bottom opening should not be blocked by placing the projector on a bed, sofa, rug, or other similar surface. This projector should never be placed near or over a radiator or heat register.

This projector should not be placed in a built-in installation such as a book case unless proper ventilation is provided.

Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the projector.

This projector should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied, consult your authorized dealer or local power company.

Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on the power cord. Do not locate this projector where the cord may be damaged by persons walking on it.

Do not attempt to service this projector yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

Unplug this projector from wall outlet and refer servicing to qualified service personnel under the following conditions:

a.When the power cord or plug is damaged or frayed.

b.If liquid has been spilled into the projector.

c.If the projector has been exposed to rain or water.

d.If the projector does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the projector to normal operation.

e.If the projector has been dropped or the cabinet has been damaged.

f.When the projector exhibits a distinct change in performance-this indicates a need for service.

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or injury to persons.

Upon completion of any service or repairs to this projector, ask the service technician to perform routine safety checks to determine that the projector is in safe operating condition.

Voor de klanten in Nederland

Bij dit product zijn batterijen geleverd.

Wanneer deze leeg zijn, moet u ze niet weggooien maar inleveren als KCA.

3

COMPLIANCES

Federal Communication Commission Notice

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures :

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.

Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment.

Model Number

: PLC-XP50/PLC-XP51/PLC-XP50L/PLC-XP51L

Trade Name

: Sanyo

Responsible party

: SANYO FISHER COMPANY

Address

: 21605 Plummer Street, Chatsworth, California 91311

Telephone No.

: (818)998-7322

AC POWER CORD REQUIREMENT

The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.

AC Power Cord for the United States and Canada :

AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and certified by the Canadian Standard Association (CSA).

AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be

unable to insert the plug into the outlet, contact your electrician.

GROUND

 

AC Power Cord for the United Kingdom :

This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug. Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the same rating, marked thus ASA . If the fuse cover is detachable, never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of the plug (i.e. red or orange). Fuse covers are available from the Parts Department indicated in your User Instructions.

If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed. The end of the flexible cord should be suitably prepared and the correct plug fitted. (See Over)

WARNING : A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED IN A LIVE SOCKET OUTLET.

The Wires in this mains lead are coloured in accordance with the following code: Green-and-yellow ············ Earth

Blue ································· Neutral Brown ······························ Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:

The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured green or green-and-yellow.

The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

WARNING : THIS APPARATUS MUST BE EARTHED.

THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.

4

TABLE OF CONTENTS

FEATURES AND DESIGN

PREPARATION

NAME OF EACH PART OF PROJECTOR SETTING-UP PROJECTOR

CONNECTING AC POWER CORD POSITIONING PROJECTOR ADJUSTABLE FEET

INSTALLING PROJECTOR IN PROPER POSITION MOVING PROJECTOR

CONNECTING PROJECTOR

TERMINALS OF PROJECTOR CONNECTING TO COMPUTER CONNECTING TO VIDEO EQUIPMENT

6

COMPUTER INPUT

23

 

SELECTING INPUT SOURCE

23

7

SELECTING COMPUTER SYSTEM

23

PC ADJUSTMENT

25

 

7

AUTO PC ADJUSTMENT

25

MANUAL PC ADJUSTMENT

26

8

PICTURE IMAGE SELECT

28

8

IMAGE LEVEL SELECT

28

9

PICTURE SCREEN ADJUSTMENT

29

10

 

 

10

VIDEO INPUT

30

11

 

 

12

SELECTING INPUT SOURCE

30

 

SELECTING VIDEO SYSTEM

31

12

PICTURE IMAGE SELECT

32

IMAGE LEVEL SELECT

32

13

PICTURE SCREEN ADJUSTMENT

33

14

 

 

 

PICTURE IMAGE

34

BEFORE OPERATION

15

34

 

PICTURE IMAGE ADJUSTMENTS

OPERATION OF REMOTE CONTROL

15

 

LASER POINTER FUNCTION

15

 

REMOTE CONTROL BATTERIES INSTALLATION

16

 

TOP CONTROLS AND INDICATORS

17

 

OPERATING ON-SCREEN MENU

18

 

HOW TO OPERATE ON-SCREEN MENU

18

 

FLOW OF ON-SCREEN

 

 

MENU BAR

 

 

BASIC OPERATION

20

TURNING ON / OFF PROJECTOR

20

ADJUSTING SCREEN

21

ZOOM ADJUSTMENT

21

FOCUS ADJUSTMENT

21

LENS SHIFT ADJUSTMENT

21

KEYSTONE ADJUSTMENT

21

PICTURE FREEZE FUNCTION

22

NO SHOW FUNCTION

22

P-TIMER FUNCTION

22

SOUND ADJUSTMENT

22

TRADEMARKS

Apple, Macintosh, and PowerBook are trademarks or

IBM and PS/2 are trademarks or registered trademarks

Windows and PowerPoint are registered trademarks of

Each name of corporations or products in the owner's respective corporation.

5

FEATURES AND DESIGN

This Multimedia Projector is designed with most advanced technology for portability, durability, and ease of use. This projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology.

Compact Design

 

Digital Zoom (for Computer)

This projector is extremely compact in size and weight. It is designed to carry and work anywhere you wish to use.

Compatibility

This projector widely accepts various video and computer input signals including;

Computers

IBM-compatible or Macintosh computer up to 1280 x 1024 resolution.

6 Color Systems

NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PAL- N color system can be connected.

Component Video

Component video signal, such as a DVD player output high definition TV signals including 480i, 480p, 575i, 575p, 720p, 1035i or 1080i, can be connected.

S-Video

S-Video signal, such as a S-VHS VCR output signal, can be connected.

High Resolution Image

This projector provides 1024 x 768 dots resolution for computer input and 800 horizontal TV lines. Resolution from a computer between XGA (1024 x 768) and SXGA (1280 x 1024) is compressed into 1024 x 768 dots. This projector cannot display image of over 1280 x 1024 dots. When resolution of your computer is over than 1280 x 1024, reset a computer output for lower resolution.

Multi-Scan System

This projector has Multi-Scan System to conform to almost all computer output signals quickly. There is no need for troublesome manual adjustment of frequency and other settings.

One-Touch Auto PC Adjustment

Incoming computer video signals are recognized and best adjustment is automatically set by Auto PC Adjustment. No complicated setup is necessary and projection is always precise.

Motor-driven Lens Shift

Projection lens can be moved up and down with motordriven lens shift function. This function makes it easy to provide projected image where you want.

Zoom and focus can be also adjusted with motor-driven operation.

Digital Zoom function adjusts image size to approx. 1/4 ~ 49 times of original image size, allowing you to focus on crucial information at a presentation.

Keystone Correction

Positioning of a projector may result in distorted image being displayed in a trapezoid shape. Keystone Correction solves this problem by digitally altering projection to produce undistorted images.

Power Management

Power Management function is provided to reduce power consumption while a projector is not in use.

This Power Management function operates to turn Projection Lamp off when a projector detects signal interruption and any button is not pressed. Projection Lamp is automatically turned on again when a projector detects signal or any operation button is pressed.

This projector is shipped with this function ON.

Digital Visual Interface

This projector is equipped with DVI 24-pin terminal for connecting DVI output from a computer.

Laser Pointer Function

Remote Control Unit supplied with this projector includes Laser Pointer function. This function helps you to make a smart presentation on a projected screen.

Wireless Mouse

Remote Control Unit supplied with this projector has Wireless Mouse function for a connected computer. This function enables you to operate both projector and computer with Remote Control Unit only.

Multilanguage Menu Display

Operation menu is displayed in; English, German, French, Italian, Spanish, Portuguese, Dutch, Swedish, Russian, Chinese, Korean or Japanese.

PJ-Net Organizer (Optional)

PJ-Net Organizer enables the projector to display the image of the computer screen and the data image stored in the computer via a network. The projector can be also controlled and maintained through a web browser.

6

Sanyo PLC-XP51L, PLC-XP51, PLC-XP50 User Manual

PREPARATION

NAME OF EACH PART OF PROJECTOR

FRONT OF CABINET

TOP CONTROLS

AND INDICATORS

PROJECTION LENS

 

 

 

 

AIR INTAKE

 

 

 

 

VENT

LENS COVER

 

 

 

INFRARED

SPEAKERS

REMOTE RECEIVER

 

BACK OF CABINET

POWER CORD

 

TERMINALS

INFRARED

EXHAUST VENT

CONNECTOR

AND CONNECTORS

REMOTE RECEIVER

 

 

 

 

 

 

 

HOT AIR EXHAUSTED !

Air blown from exhaust vent is hot. When using or installing a projector, following precautions should be taken.

● Do not put a flammable object near this vent. ● Keep rear grills at least 3.3’(1 m) away from any object, especially heat-sensitive object.

● Do not touch this area, especially screws and metallic parts. This area will become hot while a projector is used.

This projector detects internal temperature

and automatically controls operating power LAMP COVER of Cooling Fans.

CARRYING

HANDLE

When attached the PJ-Net organizer (optional part) to the projector, remove the these parts. Refer to the owner's manual in the optional PJ-Net organizer.

BOTTOM OF CABINET

AIR INTAKE VENTS

This projector is equipped with cooling fans for protection from overheating. Pay attention to following to ensure proper ventilation and avoid a possible risk of fire and malfunction.

● Do not cover vent slots.

● Keep side clear of any objects. Obstructions may block cooling air.

ADJUSTABLE FEET

AND

FEET LOCK LATCHES

7

PREPARATION

SETTING-UP PROJECTOR

CONNECTING AC POWER CORD

This projector uses nominal input voltages of 100-120 V or 200-240 V AC. This projector automatically selects correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce risk of electrical shock, do not plug into any other type of power system.

Consult your authorized dealer or service station if you are not sure of type of power supply being in use.

Connect a projector with a peripheral equipment before turning a projector on. (Refer to pages 12 ~ 14 for connection.)

CAUTION

For safety, unplug AC Power Cord when an appliance is not used.

When this projector is connected to outlet with AC Power Cord, an appliance is in Stand-by Mode and consumes a little electric power.

Connect AC Power Cord (supplied) to a projector. AC outlet must be near this equipment and must be easily accessible.

NOTE ON POWER CORD

AC Power Cord must meet requirement of country where you use a projector.

Confirm an AC plug type with chart below and proper AC Power Cord must be used.

If supplied AC Power Cord does not match your AC outlet, contact your sales dealer.

Projector side

 

 

 

 

 

AC Outlet side

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

For the U.S.A. and Canada

For Continental Europe

For the U.K.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Ground

 

 

 

 

To POWER CORD

 

 

 

 

 

To the AC Outlet.

 

To the AC Outlet.

 

 

CONNECTOR on your

 

 

To the AC Outlet.

 

(200 - 240 V AC)

 

(120 V AC)

 

 

projector.

 

 

(200 - 240 V AC)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8

PREPARATION

POSITIONING PROJECTOR

NOTE: The figures below are only for Model PLC-XP50/PLC-XP51.

Projection lens is not provided with Model PLC-XP50L/PLC-XP51L.

This projector is designed to project on a flat projection surface.

Projector can be focused from 4.6’ (1.4m) ~ 47.3’ (14.4m).

Refer to figure below to adjust screen size.

ROOM LIGHT

Brightness in room has a great influence on picture quality. It is recommended to limit ambient lighting in order to provide best image.

 

 

 

47.3’(14.4m)

 

 

35.4’(10.8m)

Max. Zoom

400”

 

 

23.6’(7.2m)

 

 

 

 

11.8’(3.6m)

300”

 

308”

200”

 

4.6’(1.4m)

 

 

 

 

231”

Min. Zoom

 

 

100”

 

40”

154”

 

 

 

 

 

77”

 

 

 

 

 

 

 

31”

 

 

 

 

Screen

 

Max. Zoom

 

40”

 

 

100”

 

 

150”

 

 

200”

 

 

250”

 

 

300”

 

 

400”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Size

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Min. Zoom

 

31”

 

 

77”

 

 

115”

 

 

154”

 

 

192”

 

 

231”

 

 

308”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Distance

 

4.6’ (1.4m)

 

 

11.8’ (3.6m)

 

 

17.7’ (5.4m)

 

 

23.6’ (7.2m)

 

 

29.5’ (9.0m)

 

 

35.4’ (10.8m)

 

 

47.3’ (14.4m)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LENS SHIFT ADJUSTMENT

Projection lens can be moved up and down with motor-driven lens shift function. This function makes it easy to provide projected image where you want. U/D ratio can be adjusted 10 : 0 ~ 1 : 1 (refer to figure below.). Refer to P 21 for operation.

Highest (10 : 0) Lowest (1 : 1)

1

10 : 0

1

9

PREPARATION

ADJUSTABLE FEET

Picture tilt and projection angle can be adjusted by rotating ADJUSTABLE FEET. Projection angle can be adjusted to 10.5 degrees.

1

Lift front of a projector and pull FEET LOCK LATCHES

 

on both sides of a projector.

2

Release FEET LOCK LATCHES to lock ADJUSTABLE

 

FEET and rotate ADJUSTABLE FEET to fine tune

 

position and tilt.

3

To shorten ADJUSTABLE FEET, lift front of a projector

 

and pull and undo FEET LOCK LATCHES.

Position and keystone distortion of image can be adjusted using Menu Operation. (Refer to P 21 and 37.)

ADJUSTABLE FEET

FEET LOCK

 

LATCHES

INSTALLING PROJECTOR IN PROPER POSITION

Install the projector properly. Improper installation may reduce the lamp lifetime and cause a fire hazard.

10˚

Do not tilt the projector more than 10 degrees above and below.

10˚

Do not point the projector up to project an image.

NO UPWARD

Do not point the projector down to project an image.

NO DOWNWARD

Do not put the projector on either side to project an image.

NO SIDEWAYS

10

PREPARATION

MOVING PROJECTOR

Use Carry Handle when moving a Projector.

When moving a projector, replace lens cover and retract feet to prevent damage to lens and cabinet.

When this projector is not in use for an extended period, put it into case (dust cover) supplied with this projector.

CAUTION IN CARRYING OR TRANSPORTING A PROJECTOR

Do not drop or bump a projector, otherwise damages or malfunctions may result.

When carrying a projector, use a suitable carrying case.

Do not transport a projector by using a courier or transport service in an unsuitable transport case. This may cause damage to a projector. To transport a projector through a courier or transport service, consult your dealer for best way.

11

CONNECTING PROJECTOR

TERMINALS OF PROJECTOR

This projector has input and output terminals on its back for connecting computers and video equipment. Refer to figures on pages 12 to 14 and connect properly.

COMPUTER AUDIO

INPUT 1/AUDIO MONITOR

OUTPUT JACK

This terminal is switchable and can be used as computer audio input 1 or audio monitor output (variable).

Set the terminal up as either Computer audio input 1 or Audio Monitor output properly before using this terminal.

Refer to P13, P23.)

COMPUTER INPUT/MONITOR OUTPUT TERMINAL (ANALOG)

This terminal is switchable and can be used as computer input or monitor output. Set the terminal up as either Computer input or Monitor output properly before using this terminal.

Refer to P13, P23.)

Note; This terminal outputs from 5 BNC type computer input on INPUT 2 jacks only.

COMPUTER INPUT

TERMINAL (DIGITAL)

Connect computer output (Digital DVI-D type) to this terminal.

HD (HDCP Compatible) signal can also be connected.

Refer to P13.)

COMPUTER AUDIO INPUT 2 JACK

Connect an audio output (stereo) from computer to this jack.

(Refer to P13.)

R/C JACK

USB CONNECTOR (Series B)

When controlling computer with Remote Control Unit of this projector, connect USB terminal of your personal computer to this terminal. (Refer to P13.)

RESET BUTTON

This projector uses a micro processor to control this unit, and occasionally, this micro processor may malfunction and need to be reset. This can be done by pressing RESET button with a pen, which will shut down and restart unit. Do not use RESET function excessively.

INPUT 1

 

IN/OUT

 

DIGITAL(DVI-D)

 

 

 

 

 

 

 

R/C JACK

AUDIO 1

USB

RESET

 

CONTROL PORT

IN/OUT

 

 

AUDIO

 

 

G

B

 

R

H/V

 

V

 

Cb/Pb

 

Cr/Pr

 

 

 

 

 

 

INPUT 2

 

 

 

VIDEO/Y Cb/Pb Cr/Pr

R–AUDIO–L

S–VIDEO

 

 

 

 

 

 

 

)

 

 

 

INPUT 3

 

 

 

When using Wired/Wireless Remote Control Unit as Wired Remote Control, Connect Wired Remote Control Unit to this jack with Remote Control Cable (supplied).

CONTROL PORT CONNECTOR

When controlling computer with Remote Control Unit of this projector, connect mouse port of your personal computer to this connector. (Refer to P13.)

Do not press this button. This button is used for our optional accessories.

5 BNC INPUT JACKS

Connect component video output (Y, Cb, Cr or Y, Pb, Pr) from video equipment to VIDEO/Y, Cb/Pb and Cr/Pr jacks or connect computer output {5 BNC Type (Green, Blue, Red, Horiz. Sync and Vert. Sync.)} from computer to G, B, R, H/V and V jacks. (Refer to P13 and 14.)

VIDEO INPUT JACKS

 

AUDIO INPUT JACKS

 

S-VIDEO INPUT JACK

Connect composite video

Connect an audio output

 

Connect S-VIDEO

output from video equipment

from video equipment to

 

output from video

to VIDEO/Y jack or connect

these jacks.

 

equipment to this

component video outputs to

(Refer to P14.)

 

jack. (Refer to P14.)

VIDEO/Y, Cb/Pb and Cr/Pr

 

 

 

jacks. (Refer to P14.)

 

 

 

12

CONNECTING PROJECTOR

CONNECTING TO COMPUTER

Cables used for connection ( = Cable or adapter is not supplied with this projector.)

• VGA Cable (HDB 15 pin)

• Control Cable for PS2 Port , or ADB Port

• DVI-Digital Cable (for Single Link T.M.D.S.)

• USB Cable

• BNC Cable

• MAC Adapter (When connecting to Macintosh computer)

• Control Cable for Serial Port

• Audio Cables (Mini Plug (stereo) x 2)

IBM-compatible computer or Macintosh computer (VGA / SVGA / XGA / SXGA)

 

 

Desktop type

Laptop type

 

Monitor Output

Monitor Output

Monitor Output

USB port

Audio Output Serial port

PS/2 port

ADB port

or

 

 

 

 

 

 

Monitor Input

 

 

 

 

 

 

 

USB

Audio

 

Control Cable

Control Cable

Control Cable

 

MAC Adapter

 

DVI

 

Cable

 

for Serial Port

for PS/2 Port

for ADB Port

 

 

 

Cable

 

 

 

 

 

 

 

 

 

BNC

Set slide switches

 

Cable

 

 

(stereo)

 

Terminal

Terminal

Terminal

according to chart

 

 

 

 

 

 

 

Cable

 

 

 

 

 

 

 

 

 

 

 

below.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VGA Cable

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

COMPUTER

Use one of these Control

 

 

 

 

 

 

 

 

 

AUDIO IN 1 or 2

 

 

 

 

 

 

 

 

 

Cables corresponding with

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

terminal of your computer.

 

 

USB

 

 

 

 

 

 

 

 

 

COMPUTER IN ANALOG

 

 

 

 

COMPUTER IN DIGITAL

 

 

CONTROL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PORT

 

 

 

INPUT 1

 

 

 

 

 

 

 

 

 

ANALOG IN/OUT

 

DIGITAL(DVI-D)

 

 

NOTE;

 

 

 

 

 

 

 

 

 

R/C JACK

 

 

 

 

 

 

 

 

 

 

 

 

This terminal is switchable.

 

NOTE;

AUDIO 1

USB

RESET

AUDIO 2

CONTROL PORT

 

Set

the terminal

up as either

 

IN/OUT

 

 

 

 

 

 

 

Computer audio input 1 or audio

 

 

 

 

 

 

 

 

 

 

This terminal is switchable.

 

 

 

 

 

 

AUDIO OUT

 

 

 

 

 

 

 

monitor output (variable) before using

 

Set the terminal

G

B

 

R

H/V

 

V

 

 

up as

 

 

 

 

 

 

 

this terminal. (See page 23.)

 

either Computer input or

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Monitor output

VIDEO/Y

Cb/Pb

Cr/Pr

 

 

 

 

 

 

 

before

 

 

INPUT 2

 

 

 

 

 

 

 

using this terminal.

VIDEO/Y Cb/Pb

Cr/Pr

R–AUDIO–L

S–VIDEO

 

 

 

 

 

 

 

 

 

 

 

(See page 23.)

 

 

 

 

 

 

 

Audio Cable

 

NOTE :

 

 

 

 

 

 

(MONO)

 

 

 

Terminals

 

 

 

 

(stereo)

 

 

 

 

INPUT 3

 

 

 

When connecting cable, power cords

 

 

 

 

 

 

 

 

of a Projector

 

 

 

 

 

 

 

 

of both a projector and external

 

 

 

 

 

 

 

 

 

 

equipment should be disconnected

 

 

 

 

 

 

 

 

 

 

from AC outlet. Turn a projector and

MAC ADAPTER

 

 

 

 

 

 

 

 

peripheral equipment on before

 

 

 

 

 

 

 

 

computer is switched on.

 

Set switches as shown in table

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Audio Input

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

below depending on RESOLU-

ON

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

External Audio Equipment

 

 

 

TION MODE that you want to

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ON

 

 

 

 

DIP

 

 

 

 

 

 

 

 

 

use before you turn on projec-

 

 

 

 

 

 

1

2

3

 

4

 

5

6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Audio Speaker

 

tor and computer.

 

 

 

OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Audio Amplifier

 

 

 

 

(stereo)

 

 

 

 

1

 

2

3

4

 

 

 

 

 

5

 

 

 

 

 

6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

13" MODE (640 x 480)

ON

 

ON

OFF

OFF

 

OFF

 

 

 

OFF

 

 

 

 

 

 

 

 

 

 

 

 

16" MODE (832 x 624)

OFF

 

ON

OFF

ON

 

OFF

 

 

 

OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

19" MODE (1024 x 768)

OFF

 

ON

ON

OFF

 

OFF

 

 

 

OFF

 

 

 

 

 

 

 

 

 

 

 

 

21" MODE (1152 x 870)

ON

 

ON

ON

ON

 

OFF

 

 

 

OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

13

CONNECTING PROJECTOR

CONNECTING TO VIDEO EQUIPMENT

Cables used for connection ( = Cable is not supplied with this projector.)

• Video Cable (RCA x 1 or RCA x 3)

• Audio Cable {Mini Plug (stereo)}

• BNC Cable

• Scart Cable

S-VIDEO Cable

Audio Cable (RCA x 2)

Video Source (example)

Component video output equipment.

Video Cassette Recorder

Video Disc Player

(such as DVD player or high-definition TV source.)

 

RGB Scart Composite

Component Video

Composite

Component Video Audio Output

S-VIDEO

21-pin Output Video Output

 

 

Output

Video Output

Output

Output

 

 

 

(Y, Cb/Pb, Cr/Pr)

 

(Y, Cb/Pb, Cr/Pr)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Scart Cable

Video Cables

 

 

 

 

 

(RCA x 1 or

 

 

 

 

 

 

 

 

 

 

 

 

RCA x 3)

 

 

 

Audio Cable

S-VIDEO

 

 

 

BNC Cable

 

(RCA x 2)

Cable

 

 

 

 

 

 

 

VIDEO

Y - Cb/Pb - Cr/Pr

VIDEO

Y - Cb/Pb - Cr/Pr

AUDIO IN

S-VIDEO

COMPUTER IN ANALOG

 

INPUT 1

 

 

ANALOG IN/OUT

DIGITAL(DVI-D)

 

 

 

R/C JACK

AUDIO OUT

IN/OUT

 

AUDIO 2

 

AUDIO 1 USB

RESET

CONTROL PORT

 

G

B

R H/V V

 

VIDEO/Y

Cb/Pb

Cr/Pr

 

 

 

 

INPUT 2

 

 

VIDEO/Y Cb/Pb Cr/Pr

R–AUDIO–L

S–VIDEO

Audio Cable

 

 

 

 

(stereo)

 

 

(MONO)

 

 

 

INPUT 3

 

NOTE;

 

 

 

 

 

 

 

This terminal is switchable.

 

 

 

 

Set the terminal up as either

 

 

 

 

Computer audio input 1 or audio

Terminals

 

monitor output (variable) before

 

of a Projector

 

using this terminal.

 

(See page 23.)

Audio Input

External Audio Equipment

Audio Amplifier

 

 

Audio Speaker

 

 

 

(stereo)

 

 

 

 

 

 

 

 

 

 

NOTE :

When connecting cable, power cords of both a projector and external equipment should be disconnected from AC outlet.

14

BEFORE OPERATION

OPERATION OF REMOTE CONTROL

Left Side

ON

OFF ALL

ALL-OFF SWITCH

When using Remote Control Unit, turn this switch to “ON.” And turn it to “ALL OFF” when it is not used.

INSIDE THE BATTERY COMPARTMENT BOX

This remote control provide the DIP switches into the battery compartment box.

Slide the SW4 (LASER ON/OFF switch) to "OFF" position. The laser pointer function is not operated.

Set switches 1-3 as shown in table below depending on Code No. that you want to select remote control code.

(Refer to P39.)

DIP SWITCH SETTING

 

 

 

 

 

 

 

SW4 ........ LASER ON/OFF

 

 

 

 

 

 

 

SW1

SW2

SW3

Code No.

 

 

 

 

4

 

ON

ON

ON

Code 1

 

 

 

 

 

 

 

ON

 

 

 

3

 

ON

ON

OFF

Code 2

 

 

 

2

 

ON

OFF

ON

Code 3

 

 

 

 

 

 

 

ON

OFF

OFF

Code 4

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

OFF

ON

ON

Code 5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OFF

ON

OFF

Code 6

 

 

 

 

 

 

 

 

 

 

 

 

 

OFF

OFF

ON

Code 7

 

 

 

 

 

 

 

OFF

OFF

OFF

Code 8

LASER POINTER (Drag ON)

INDICATOR

Lights red while laser beam is emitted from Laser Light Window.

Lights green when drag ON position. (P41)

MUTE BUTTON

Used to mute sound. (P22)

DRAG ON/OFF BUTTON

Used to select drag ON/OFF position. (P41)

LEFT CLICK BUTTON

Used as a PC mouse in Wireless Mouse Operation. Press this button and the mouse pointer button to drag a selected screen object. (P41)

LASER BUTTON

Used to operate Laser Pointer Function. Laser beam is emitted while pressing this button within 1 minute.

When using this Laser Pointer for more than 1 minute, release LASER button and press it again.

FOCUS BUTTON

Used to adjust focus. (P21)

LOCK

AUTO PC ON-OFF

D.ZOOM FREEZE NO SHOW

MUTE IMAGE

VOLUMESELECT VOLUME+

MENU KEYSTONE

LASER

P-TIMER INPUT 1

ZOOM COLOR.M INPUT 2

INPUT 3

FOCUS LENS NETWORK

POWER ON-OFF BUTTON

Used to turn projector on or off. (P20)

AUTO PC ADJ. BUTTON

Use to operate AUTO PC Adjustment function. (P25)

IMAGE BUTTON

Used to select image level. (P28, 32)

KEYSTONE BUTTON

Used to correct keystone distortion. (P21, 37)

MOUSE POINTER

Used as a PC mouse in Wireless Mouse Operation. (P41)

RIGHT CLICK BUTTON

Used as a PC mouse in Wireless Mouse Operation. (P41)

LENS SHIFT BUTTON

Used to select LENS SHIFT function. (P21)

WIRED REMOTE JACK

When using as Wired Remote Control, connect Remote Control Cable to this jack.

Battery installation is required when using as Wired Remote Control.

LASER POINTER FUNCTION

This Remote Control Unit emits a laser beam as laser pointer function from Laser Light Window. When LASER button is pressed, laser light goes on. And when LASER button is being pressed for more than 1 minute or LASER button is released, light goes off. LASER POINTER INDICATOR lights RED and Laser is emitted with RED light to indicate laser beam is being emitted.

Laser emitted is a class II laser; therefore, do not look into Laser Light Window or shine laser beam on yourself or other people. Three marks below are caution labels for laser beam.

CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result hazardous radiation exposure.

These caution labels are put on remote control.

LASER POINTER INDICATOR

Laser Light Window

15

BEFORE OPERATION

D.ZOOM BUTTON

Used to select DIGITAL ZOOM +/– mode and resize image. (P29)

SELECT BUTTON

Used to execute the selected item, or to expand or compress image in DIGITAL ZOOM +/- mode. (P29)

MENU BUTTON

Used to select MENU operation. (P18, 19)

P-TIMER BUTTON

Used to operate P- TIMER function. (P22)

ZOOM BUTTON

Used to adjust zoom. (P21)

COLOR MANAGEMENT BUTTON

Used to operate COLOR MANAGEMENT.

(P34)

LOCK

AUTO PC ON-OFF

D.ZOOM FREEZE NO SHOW

MUTE IMAGE

VOLUMESELECT VOLUME+

MENU KEYSTONE

LASER

P-TIMER INPUT 1

ZOOM COLOR.M INPUT 2

INPUT 3

FOCUS LENS NETWORK

NO

Used black

Used

POINT

Used adjust MENU to ZOOM POINT are +/-

Used source (P23)

Used source (P24,

Used source (P30)

NETWORK BUTTON

Used to select network input. (Option)

Operating Range

Point Remote Control Unit toward projector (Receiver Window) whenever pressing any button. Maximum operating range for Remote Control Unit is about 16.4’ (5m) and 60° in front and rear of a projector.

60°

16.4’ (5 m)

16.4’ (5 m)

60°

Remote Control Batteries Installation

1

2

3 Replace compartment lid.

Press lid downward and slide it.

Two AA size batteries

For correct polarity (+ and

–), be sure battery terminals are in contact with pins in compartment.

To insure safe operation, please observe following precautions :

Use (2) AA, UM3 or R06 type alkaline batteries.

Replace two batteries at same time.

Do not use a new battery with an used battery.

Avoid contact with water or liquid.

Do not expose Remote Control Unit to moisture, or heat.

Do not drop Remote Control Unit.

If a battery has leaked on Remote Control Unit, carefully wipe case clean and install new batteries.

Danger of explosion if battery is incorrectly replaced.

Dispose of used batteries according to batteries manufacturers instructions and local rules.

16

BEFORE OPERATION

TOP CONTROLS AND INDICATORS

This projector has CONTROL BUTTONS (TOP CONTROLS) and INDICATORS on its top.

LAMP REPLACE INDICATOR

 

WARNING TEMP. INDICATOR

 

READY INDICATOR

Turns to yellow when

Flashes

red

when

Lights green when a

life of projection lamp

internal

projector

projector is ready to be

draws to an end. (P44)

temperature

is too

turned on.

And it

 

 

high. (P42)

 

 

flashes green in Power

 

 

 

 

 

 

Management

mode.

 

 

 

 

 

 

(P39)

 

LAMP INDICATOR

Becomes dim when a projector is turned on. And bright when a projector is in stand-by mode.

MENU BUTTON

Used to open or close MENU operation. (P18, 19)

ZOOM BUTTON

Used to adjust zoom. (P21)

FOCUS BUTTON

Used to adjust focus. (P21)

LENS SHIFT BUTTON

Used to select LENS

SHIFT function. (P21)

POINT (VOLUME + / – ) BUTTONS

Used to select an item or adjust value in ON-SCREEN MENU. They are also used to pan image in DIGITAL ZOOM +/– mode. (P29)

POINT LEFT/RIGHT buttons are also used as VOLUME +/– buttons.

SELECT BUTTON

Used to execute the selected item.

It is also used to expand/compress image in DIGITAL ZOOM mode. (P29)

POWER ON–OFF BUTTON

Used to turn a projector on or off. (P20)

INPUT BUTTON

Used to select input source. (P23, 24, 30)

AUTO PC ADJ. BUTTON

Used to operate AUTO PC

Adjustment function. (P25)

IMAGE BUTTON

Used to select image level. (P28, 32)

17

Loading...
+ 39 hidden pages