Multimedia Plasma Monitor
MODEL PDP-32H1ENV PDP-32H1AN PDP-32H1EN
Owner's Manual
TO THE OWNER
Before operating this Plasma Monitor, read this manual thoroughly and operate the Plasma Monitor properly.
This Plasma Monitor provides many convenient features and functions. Operating the Plasma Monitor properly enables you to manage those features and maintains it in better condition for a considerable time.
Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents.
If your Plasma Monitor seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the “Trouble-shooting” section of the end of this booklet. If the problem still persists, contact the sales dealer where you purchased the Plasma Monitor or the service center.
SAFETY PRECAUTIONS
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
●This Plasma Monitor should be set in the way indicated. If not, it may result in a fire hazard.
●Take appropriate space on the top, sides and rear of the Plasma Monitor cabinet for allowing air circulation and cooling the Plasma Monitor. Minimum distance should be taken. If the Plasma Monitor is to be built into a compartment or similarly enclosed, the minimum distances must
be maintained. Do not cover the ventilation slot on the Plasma Monitor. Heat build-up can reduce the life of your Plasma Monitor, and can also be dangerous.
●If the Plasma Monitor is not to be used for an extended time, unplug the Plasma Monitor from the power outlet.
READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.
|
|
|
SIDE and TOP |
|
|
|
REAR |
||||
|
|
|
10 cm |
|
|
|
|
|
|
|
|
10 cm |
|
|
|
|
|
|
|
6 cm |
|||
|
|
|
|
|
|
10 cm |
|
|
|
||
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CAUTION IN INSTALLING
●Handle the Plasma Monitor carefully when installing it and do not drop.
●Locate set away from heat, excessive dust, and direct sunlight.
●For correct installation and mounting it is strongly recommended to use a trained, authorized dealer. Failure to follow correct mounting procedures could result in damage to the equipment or injury to the installer.
NOTE :
When Plasma Monitor is not used for a long period of time, unlighting dots may be observed. This is caused by characteristic of the Plasma Monitor. If this occurs, turn the Plasma Monitor on and leave it on about 1 hour. These dots will gradually disappear.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE OWNER'S MANUAL WITH THIS UNIT.
2
SAFETY INSTRUCTIONS
All the safety and operating instructions should be read before the product is operated.
Read all of the instructions given here and retain them for later use. Unplug this Plasma Monitor from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Clean only with dry cloth.
Follow all warnings and instructions marked on the Plasma Monitor.
For added protection to the Plasma Monitor during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage due to lightning and power line surges.
Do not expose this Plasma Monitor to rain or use near water...
for example, in a wet basement, near a swimming pool, etc...
The Plasma Monitor shall not be exposed to dripping or
splashing. No objects filled with liquids, such as vases, shall
be placed on the Plasma Monitor.
Only use attachments/accessories specified by the manufacturer.
Do not place this Plasma Monitor on an unstable cart, stand, or table. The Plasma Monitor may fall, causing serious injury to a child or adult, and serious damage to the Plasma Monitor. Use only with a cart or stand recommended by the manufacturer, or sold with the Plasma Monitor.
CAUTION:
This Plasma Monitor for use only with following Stand and Mount Unit. Use with other stands or mount units is capable of resulting in instability causing possible injury.
SANYO Table top stand |
KA-TD-H10S |
SANYO Floor stand |
KA-TD-H10W |
SANYO Tilt mount unit |
KA-TI-H10 |
SANYO Wall mount unit |
KA-WA-H10WV |
SANYO Ceiling mount unit |
KA-CH-H10 |
An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.
Slots and openings in the back and top of the cabinet are provided for ventilation, to insure reliable operation of the equipment and to protect it from overheating.
Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
This Plasma Monitor should not be placed in a built-in installation such as a book case unless proper ventilation is provided.
Never push objects of any kind into this Plasma Monitor through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the Plasma Monitor.
This Plasma Monitor should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied, consult your authorized dealer or local power company.
Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on the power cord. Protect the power cord from being walked on or pinched particularly at plugs. convenience receptacles, and the point where they exit from the apparatus.
Do not attempt to service this Plasma Monitor yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Unplug this Plasma Monitor from wall outlet and refer servicing to qualified service personnel under the following conditions:
a.When the power cord or plug is damaged or frayed.
b.If liquid has been spilled into the Plasma Monitor.
c.If the Plasma Monitor has been exposed to rain or water.
d.If the Plasma Monitor does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the Plasma Monitor to normal operation.
e.If the Plasma Monitor has been dropped or the cabinet has been damaged.
f.When the Plasma Monitor exhibits a distinct change in performance-this indicates a need for service.
When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or injury to persons.
Upon completion of any service or repairs to this Plasma Monitor, ask the service technician to perform routine safety checks to determine that the Plasma Monitor is in safe operating condition.
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be unable to
insert the plug into the outlet, contact |
GROUND |
|
|
your electrician. |
|
Voor de klanten in Nederland
Bij dit product zijn batterijen geleverd.
Wanneer deze leeg zijn, moet u ze niet weggooien maar inleveren als KCA.
3
COMPLIANCES
European Norm Compatibility / CE
This machine is provided with the CE-mark and therewith corresponding to the norms that are valid for its operation at present. Thus the effective guidelines on the electromagnetic compatibility 89/336/EWG and safety regulations according to low voltage guideline 73/23/EWG and 93/68/EWG are guaranteed. Mutual disturbances with other electronic appliances are normally excluded, if those also are in accordance with valid norms. Sporadically disturbances cannot, however, be excluded. The product is in conformity with the directives of the valid European guidelines.
Declaration of Conformity
Model Number |
: PDP-32H1AN |
Trade Name |
: Sanyo |
Responsible party |
: SANYO FISHER COMPANY |
Address |
: 21605 Plummer Street, Chatsworth, California 91311 |
Telephone No. |
: (818)998-7322 |
●This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :
(1)this device may not cause harmful interference, and
(2)this device must accept any interference received, including interference that may cause undesired operation.
AC POWER CORD REQUIREMENT
The AC Power Cord supplied with this Plasma Monitor meets the requirement for use in the country you purchased it.
AC Power Cord for the United States and Canada :
AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be
unable to insert the plug into the outlet, contact your electrician. |
GROUND |
|
AC Power Cord for the United Kingdom :
This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug. Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the same rating, marked thus ASA . If the fuse cover is detachable, never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of the plug (i.e. red or orange). Fuse covers are available from the Parts Department indicated in your User Instructions.
If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed. The end of the flexible cord should be suitably prepared and the correct plug fitted. (See Over)
WARNING : A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED IN A LIVE SOCKET OUTLET.
The Wires in this mains lead are coloured in accordance with the following code: Green-and-yellow ············ Earth
Blue ································· Neutral Brown ······························ Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:
The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured green or green-and-yellow.
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
WARNING : THIS APPARATUS MUST BE EARTHED.
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.
4
TABLE OF CONTENTS
FEATURES AND DESIGN |
6 |
PREPARATION |
7 |
NAME OF EACH PART OF PLASMA MONITOR 7 |
|
SETTING-UP PLASMA MONITOR |
9 |
CONNECTING PLASMA MONITOR |
11 |
TERMINALS OF PLASMA MONITOR |
11 |
CONNECTING TO VIDEO EQUIPMENT |
13 |
CONNECTING TO COMPONENT VIDEO EQUIPMENT |
14 |
CONNECTING TO COMPUTER |
15 |
BEFORE OPERATION |
16 |
OPERATION OF REMOTE CONTROL |
16 |
OPERATING ON-SCREEN MENU |
18 |
BASIC OPERATION |
20 |
TURNING ON / OFF PLASMA MONITOR |
20 |
OFF TIMER |
21 |
SELECTING INPUT SOURCE |
22 |
PICTURE IMAGE LEVEL SELECT |
23 |
IMAGE LEVEL ADJUSTMENT |
24 |
WIDE SCREEN OPERATIONS |
25 |
SOUND ADJUSTMENT |
27 |
COMPUTER MODE |
28 |
SELECTING INPUT SOURCE |
28 |
SELECTING COMPUTER SYSTEM |
28 |
PC ADJUSTMENT |
29 |
VIDEO MODE |
32 |
SELECTING INPUT SOURCE |
32 |
SELECTING VIDEO SYSTEM |
33 |
SETTING |
34 |
SCREEN SAVER FUNCTION |
34 |
SETTING MENU |
35 |
CLEANING THE PLASMA MONITOR |
36 |
APPENDIX |
37 |
TROUBLESHOOTING |
37 |
TRADEMARKS
●Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.
●IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.
●Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its respective corporation.
5
FEATURES AND DESIGN
This Plasma Monitor is designed with the most advanced technology. The Plasma Monitor utilizes built-in multimedia features, a palette of 16.77 million colors, and Plasma Display Panel technology.
High Definition Plasma Panel
This Plasma Monitor has 852 x 1,024 dots High Definition Plasma Display Panel. This Plasma Display Panel has High brightness and wide viewing angle.
Input Terminals
●D-SUB, RGB input for PC (Up to XGA)
●Component input for DVD
●S-Video / Video for VCR
Compatibility
This Plasma Monitor widely accepts various video and computer input signals including;
●6 Color Systems
NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PAL- N color system can be connected.
●Component Video
Component video signals, such as a DVD player output high definition TV signals including 480i, 480p, 575i, 720p, 1035i or 1080i, can be connected.
●S-Video
S-Video signals, such as a S-VHS VCR output signals, can be connected.
●Computers
IBM-compatible and Macintosh computers.
Dynamic AI (Automatic Image control)
This Plasma Monitor provides AI (Automatic Imaging control) circuit which compensates picture contrast and brightness levels dynamically and reproduces bright and high-contrast pictures.
RS232C Terminal
This Plasma Monitor can be controlled through RS232C terminal. It allows you to use other AV systems.
Slim design
Slim design allows you to get the most advantage. When installing the Plasma Monitor in limited space, and it is well designed for easy installation.
Multi-Scan System
This Plasma Monitor has Multi-Scan System to conform to almost all computer output signals quickly. There is no need for complicated manual adjustment of frequency and other settings.
CARE FOR USING PLASMA MONITOR
Do not bump or scratch the panel surface as this causes flaws on the surface of the screen.
Do not display one non-movement still picture on the screen for a long time. Otherwise, an afterimage or ghost may appear on a part of the panel. To prevent this symptoms, apply the screen saver function in the Plasma Monitor.
There may be some tiny black points and/or blight points on the Plasma Display Panel. These points are normal.
NOTES ON OWNER'S MANUAL
This owner's manual described with the models PDP-32H1ENV and PDP-32H1AN. Some of terminals are not provided on model PDP-32H1EN. (Refer to the terminal figure on page 12. )
6
PREPARATION
NAME OF EACH PART OF PLASMA MONITOR
FRONT
MENU BUTTON
Used to select MENU operation. (P18)
PLASMA DISPLAY
PANEL
FRONT CONTROLS
AND INDICATORS
CURSOR BUTTON |
FRONT CONTROLS |
Used to set and adjust the menu data on On-Screen Menu. (P18)
OK BUTTON
Used to execute the selected menu on OnScreen Menu. (P18)
CURSOR BUTTON
Used to select the menu on On-Screen Menu. (P18)
|
OK |
|
MENU |
INPUT |
VOLUME |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
VOLUME BUTTONS |
|
|
|
|
|
MAIN ON/OFF SWITCH |
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
Used to adjust volume. |
|
|
|
|
Used to turn Plasma |
||||||||
|
|
(P27) |
|
|
|
|
|
|
Monitor on or off. (P20) |
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
INFRARED |
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
POWER INDICATOR |
|
||||
INPUT BUTTON |
|
|
|
|
|
|
|
||||||||
|
|
REMOTE RECEIVERS |
|
|
|
|
|
|
|
||||||
|
|
|
|
Light in green when power is on. |
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
Used to select input source. |
Light in red when power is off with Remote |
|
(P22) |
||
Control (standby mode), or the Plasma Monitor |
||
|
||
|
is in Power Save mode. (P20) |
7
PREPARATION
NAME OF EACH PART OF PLASMA MONITOR
BACK |
This Plasma Monitor detects |
|
COOLING FANS |
||
|
internal temperature and |
|
|
automatically |
controls |
|
operating power of Cooling |
|
|
Fans. |
|
TERMINALS
AND CONNECTORS (SIDE)
(Refer to page 11)
SPEAKER OUTPUT
TERMINALS (LEFT)
SPEAKER OUTPUT
TERMINALS
TERMINALS
AND CONNECTORS
(RIGHT)
(BACK)
(Refer to page 12)
POWER CORD
CONNECTOR
NOTES ON USING PLASMA MONITOR
For using this Plasma Monitor, Optional Stand or Mounting Bracket is needed. Those optional units are not included within this Monitor Set. Your Sales dealer can advice you of best optional unit for using Plasma Monitor. Contact your sales dealer for detail.
INSTALL PLASMA MONITOR IN PROPER DIRECTION
This Plasma Monitor can be installed in two ways, normal (horizontal) and vertical.
DO NOT INSTALL UNSPECIFIED DIRECTION, OR COOLING AIR CIRCULATION IS PREVENTED AND IT MAY RESULT IN FIRE HAZARD.
Horizontal |
Vertical |
Front Controls should be located lower.
8
PREPARATION
SETTING-UP PLASMA MONITOR
CONNECTING AC POWER CORD
This Plasma Monitor uses nominal input voltages of 100120 V or 200-240 V AC. The Plasma Monitor automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce the risk of electrical shock, do not plug into any other type of power system.
Consult your authorized dealer or service station if you are not sure of the type of power supply being in use. Connect Plasma Monitor with the peripheral equipment before turning Plasma Monitor on. (Refer to pages 13 ~ 15 for connection.)
CAUTION
For safety, unplug the AC Power Cord when the appliance is not used.
Table Top Stand
(Option)
Connect AC Power Cord (supplied) to Plasma Monitor. The AC outlet must be near this equipment and must be easily accessible.
NOTE ON THE POWER CORD
The AC Power Cord must meet the requirement of the country where you use the Plasma Monitor. Confirm the AC plug type with the chart below and the proper AC Power Cord must be used.
If the supplied AC Power Cord does not match the AC outlet, contact your sales dealer.
Plasma Monitor side |
AC Outlet side |
|
For the U.S.A. and Canada |
For Continental Europe |
For the U.K. |
Ground |
|
|
|
|
|
|
|
|
To the AC Outlet. |
|
|
To the AC Outlet. |
|
|
||
|
|
|
|
|
(220 - 240 V AC) |
|
To the POWER CORD CON- |
|
(120 V AC) |
|
To the AC Outlet. |
|
|
NECTOR on Plasma Monitor |
|
|
|
(220 - 240 V AC) |
|
|
|
|
|
|
|
||
|
|
|
|
|||
|
|
|
|
|
|
|
ATTACHING THE FERRITE CORES
Ferrite cores (supplied)
When you connect The Plasma Monitor to AC outlet, attach the supplied ferrite cores. Set the ferrite cores on the both ends of the AC power cord . Close the lid tightly until the clamps click.
9
PREPARATION
INSTALLATION OF OPTIONAL SPEAKERS AND STAND
Please read the each option's instruction manual (or installation manual) for the installation.
CAUTION IN INSTALLATION
● Through installation work, handling with more than two people is recommended. ● When holding (moving or lifting) the Plasma Monitor, hold the Monitor's body. Do not handle it by holding the attached accessory parts (the Speakers), otherwise damage
could be result.
● Provide space that enough larger than the screen size. The surface must be flat and maintained with soft material (cloth or blanket) for protecting the screen surface.
●Before placing the Plasma Monitor Screen facing down, make sure there is no object under the screen. Leaving any object may cause damage on the screen surface.
SPEAKERS (OPTIONAL)
Place the Speakers to each side of the Plasma Monitor and attach Right and Left brackets with the specified screws. Mount each screw on proper screw hole position and fix it securely.
Connect the red wire to the red terminal on both of the Plasma Monitor and the speakers and connect the black wire to the black terminal to make correct polarity.
Left Speaker
Right Speaker |
Speaker Terminal |
|
Red:(+), Black:(-) |
||
|
TABLE TOP STAND (OPTIONAL)
Assemble Table top stand according to the installation manual of the stand.
Mount the stand on the back of the Plasma Monitor by fixing the Arms with screws (3 pcs. for each arm).
Arm
Table top stand
10
CONNECTING PLASMA MONITOR
TERMINALS OF PLASMA MONITOR
This Plasma Monitor has INPUT TERMINALS and OUTPUT TERMINALS on its side and back, for connecting computers and video equipment. Refer to the figure on pages 13 to 15 and connect properly.
SIDE
RS-232C
WIRED R/C
HEADPHONE
RS-232C TERMINAL
When controlling this Plasma Monitor by computer, connect your computer to this terminal.
WIRED R/C JACK
When using Remote Control Unit as Wired Remote Control, Connect Remote Control Unit to this jack with Remote Control Cable (supplied). (Refer to page 17.)
HEADPHONE JACK
Connect Headphone (stereo).
11
CONNECTING PLASMA MONITOR
BACK
VIDEO1 INPUT JACKS
Connect video and audio outputs from |
|
PC INPUT TERMINALS |
video equipment. (Refer to P13.) |
|
Connect computer outputs to this |
|
|
|
● S-VIDEO (Mini DIN 4-type) |
|
terminals. (Refer to P15.) |
|
||
● VIDEO (RCA-type) |
SEE NOTE BELOW ● RGB (D-SUB) |
|
● AUDIO R and L(MONO) (RCA-type) |
|
● AUDIO R/L (Stereo Mini Jack) |
|
|
|
VIDEO1 IN |
|
|
|
|
PC IN |
||
|
|
|
|
|
|
|
D-SUB |
AUDIO(R/L) |
S-VIDEO |
VIDEO |
R-AUDIO-L(MONO) |
|
|
|
|
|
|
|
|
|
VD |
HD |
R |
B |
G |
|
S-VIDEO VIDEO |
R-AUDIO-L |
VIDEO R-AUDIO-L |
|
Pr /Cr |
Pb /Cb |
Y |
R-AUDIO-L |
|
|
VIDEO2 IN |
MONITOR OUT |
|
COMPONENT/RGB IN |
|
VIDEO2 INPUT JACKS
Connect video and audio outputs from video equipment. (Refer to P13.)
●S-VIDEO (Mini DIN 4-type)
●VIDEO (BNC-type)
●AUDIO R and L (RCA-type)
MONITOR OUTPUT JACKS
Connect another monitor, video recorder or external audio amplifier to these jacks. (Refer to P13~15.)
●VIDEO (RCA-type)
●AUDIO R and L (RCA-type)
NOTE : Those terminals are not provided on model PDP-32H1EN.
COMPONENT/RGB INPUT JACKS
Connect analog RGB signal outputs or component video outputs to these jacks. Connect analog RGB signal outputs to R, G, B, HD and VD jacks. (Refer to P15.) Connect component video outputs to Y, Pb/Cb and Pr/Cr jacks. (Refer to P14.)
●RGB/COMPONENT (BNC-type)
●AUDIO R and L (RCA-type)
12
CONNECTING PLASMA MONITOR
CONNECTING TO VIDEO EQUIPMENT
NOTE : Models PDP-32H1ENV and PDP-32H1AN only. |
|
|
|
|
|
Cables used for connection ( Cables are not supplied with this Plasma Monitor.) |
|||||
• 21-PIN Video Cable (BNC x 4) |
|
|
|
|
|
• Video Cable (RCA x 1) |
|
|
|
NOTE : |
|
|
|
|
When connecting Plasma Monitor, AC Power |
|
|
• Video Cable (RCA x 3) |
|
|
|
|
|
|
|
|
Cords of both Plasma Monitor and external |
|
|
• S-VIDEO Cable |
|
|
|
|
|
|
|
|
equipment should be disconnected from AC outlet. |
|
|
• Audio Cable (RCA x 2) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Video Source (example) |
|
Video Cassette Recorder |
Video Disc Player |
S-VIDEO |
Composite Video |
Composite Video |
||||||||||||||
Output |
and Audio Output |
and Audio Output |
||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
S-VIDEO |
Video Cable |
Composite video cable |
21PIN |
Cable |
(RCA x 3) |
must be connected on |
Video Cable |
|
|
"HD" terminal. |
(BNC x 4) |
S-VIDEO |
VIDEO and AUDIO R/L(MONO) |
HD |
R |
B |
G |
|
|||
|
|
|
|
|
|
||||
|
VIDEO1 IN |
|
|
|
|
|
PC IN |
||
|
|
|
|
|
|
|
|
D-SUB |
AUDIO(R/L) |
S-VIDEO |
VIDEO |
R-AUDIO-L(MONO) |
|
|
|
|
|
|
|
|
|
|
|
VD |
HD |
R |
B |
G |
|
S-VIDEO |
VIDEO |
R-AUDIO-L |
VIDEO |
R-AUDIO-L |
|
Pr /Cr |
Pb /Cb |
Y |
R-AUDIO-L |
|
VIDEO2 IN |
MONITOR OUT |
|
COMPONENT/RGB IN |
|
||||
BNC/RCA |
|
|
|
|
|
|
|
|
|
Adapter |
|
|
|
|
|
|
|
|
|
(supplied) |
|
|
VIDEO and AUDIO R/L |
|
|
|
R L |
||
|
|
|
|
|
|
||||
S-VIDEO VIDEO |
R L |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Audio Cable |
||
|
|
|
|
|
|
|
|
(RCA x 2) |
|
S-VIDEO |
|
Audio Cable |
Video Cable |
|
|
|
|
||
Cable |
|
(RCA x 2) |
(RCA x 3) |
|
|
|
|
||
Video |
|
|
|
|
|
External Audio |
|
||
|
|
|
|
|
Equipment |
|
|||
Cable |
|
|
|
|
|
|
|||
(RCA x 1) |
|
|
|
|
|
Audio Speaker |
|
||
|
|
|
|
|
|
|
|||
|
|
|
|
Composite Video |
|
|
(stereo) |
Audio Amplifier |
|
|
|
|
|
|
|
|
|
||
S-VIDEO |
Composite Video |
|
|
|
|
|
|
||
|
and Audio Input |
|
|
|
|
|
|||
Output |
and Audio Output |
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|||
Another |
|
|
|
|
|
|
|
|
|
Video Source |
|
|
|
|
External Monitor |
|
|
||
|
|
|
|
|
|
|
13
CONNECTING PLASMA MONITOR
CONNECTING TO COMPONENT VIDEO EQUIPMENT
NOTE : Models PDP-32H1ENV and PDP-32H1AN only.
Cables used for connection (Cables are not supplied with this Plasma Monitor.)
•Video Cable (RCA x 3) or (BNC x 3)
•Audio Cable (RCA x 2)
NOTE :
When connecting Plasma Monitor, AC Power Cords of both Plasma Monitor and external equipment should be disconnected from AC outlet.
|
|
Component video output equipment. |
|
|
|
Component Video |
|
|
|
|
(such as DVD player or |
DVD player |
|
|
|
Source (example) |
|
||
|
high-definition TV source.) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Component Video Audio Output
Output
|
|
|
or |
|
|
|
|
|
|
Video |
Video Cable |
|
|
Audio Cable |
|
|
|
Cable |
(RCA x 3) |
|
|
(RCA x 2) |
|
|
|
(BNC x 3) |
|
|
|
|
|
|
|
BNC/RCA |
|
|
|
|
R L |
|
|
|
|
|
|
|
|
|
|
Adapter |
|
|
|
|
|
|
|
(supplied) |
|
|
|
|
|
|
|
|
|
Pr/Cr |
Pb/Cb |
Y |
|
|
VIDEO1 IN |
|
|
|
|
PC IN |
|
|
|
|
|
|
|
D-SUB |
AUDIO(R/L) |
S-VIDEO |
VIDEO R-AUDIO-L(MONO) |
|
|
|
|
|
|
|
|
VD |
HD |
R |
B |
G |
|
S-VIDEO |
VIDEO R-AUDIO-L |
VIDEO R-AUDIO-L |
|
Pr /Cr |
Pb /Cb |
Y |
R-AUDIO-L |
|
VIDEO2 IN |
MONITOR OUT |
|
COMPONENT/RGB IN |
|
R L
Audio Cable
(RCA x 2)
External Audio
Equipment
Audio Speaker
(stereo)
Audio Amplifier
14