INSTRUCTION MANUAL |
|
MTS-2000 & |
|
|
MTS-2030 J-Mount |
|
|
|
Feed-Through Mounts |
|
|
for Cylindrical |
|
|
Environmental Camera Housings |
|
|
About this manual
Before installing and using this unit, please read this manual carefully. Be sure to keep it available
for later reference.
SAFETY PRECAUTIONS
The exclamation point within an equilateral triangle is intended to alert the user to presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
SECURITE
Le point d'exclamation à l'intérieur d'un triangle équilatéral avertit l'utilisateur de la présence d'instructions importantes d'utilisation et de maintenance dans la documentation accompagnant l'appareil.
3 DESCRIPTION
MTS-2000 12-in (30-cm) feed-through mount and MTS-2030 15-in (40-cm) feed-through J-mount.
This indoor/outdoor mounting equipment is designed for fixed camera or camera housing installations up to 9 kg (20 lb) rated load.These models are made of lightweight aluminum and feature welded construction, providing an extremely rigid camera mount. The MTS-2000 and MTS-2030 can be used with the VSE-2300 and VSE-2400 series camera housings. All mounts come fully assembled.
SICHERHEITSVORKENHRUNGEN
Das Ausrufezeichen in dem gleichseitigen Dreieck ist dazu da, den Benutzer auf wich-tige Inbetriebnahmeund Instandhaltungs-vorschriften hinzuweisen, die dem Gerät in Form einer Broschüre beigelegt sind.
PRECAUCIONES DE SEGURIDAD
El símbolo de exclamación dentro de un triángulo equilátero, se muestra con el objetivo de alertar al ususario de que instrucciones de operación y mantenimiento importantes acompañan al equipo.
1 UNPACKING
Unpack carefully.This is mechanical equipment and should be handled with care.
Check for the following items:
•Verify the unit model number.
•Instructions for Use.
If an item appears to have been damaged in shipment, replace it properly in its carton and notify the shipper. If any items are missing, notify Sanyo.The shipping carton is the safest container in which the unit may be transported. Save it for possible future use.
2 SERVICE
If the unit ever needs repair service, the customer should contact Sanyo.
4 INSTALLATION
1. Determine a secure wall mounting location.
WARNING:All mounts are designed to support a load only in a vertical direction. Mounts MUST be positioned as shown under SPECIFICATIONS.
2.
CAUTIONS:
a.For a secure installation, use four 8-mm (5/16-in) diameter fasteners (not included). Use stainless steel or zinc plated fasteners.
b.If bolts are used, they should extend through the mounting surface and be secured with flat washers, lock washers, and nuts on the opposite side. Each bolt must have a minimum pull-out strength of 200 kg
(450 lb).
c.If studs are used, they should be anchored in concrete or welded to a steel backer plate. Each stud must have a minimum pull out strength of 200 kg (450 lb).
d.If the wall mount is attached to wood or to a blind structure (with no access to the rear), each fastener must have a minimum pull-out strength of at least 200 kg (450 lb).
3.Locate the four holes or stud locations using the flange as
atemplate (four holes equally spaced on a 69.9-mm
(2-3/4-in bolt circle).
4.Feed wires through the large hole in the flange or through the slot on the surface where the camera housing mounts.
5.Install the mount using bolts or studs at least 8-mm (5/16-in) in diameter.
6.To mount the camera or camera housing:
a.Mount camera with a 1/4-20 bolt and lock washer (not furnished) in the center hole of the adjustable head.
b.Mount housings with three 1/4-20 bolts and lock washers (not furnished).
c.Lock mount head in position by using the supplied 1/8-inch long-arm hex wrench to tighten screws.
2
Loading...