Sanyo LCD-32E3, LCD-42E3, LCD-26E3, LCD-19E3 User Manual

4 (1)

 

 

 

 

 

CAUTION

 

THIS SYMBOL INDICATES THAT DANGEROUS

 

 

 

VOLTAGE CONSTITUTING A RISK OF ELECTRIC

 

RISK OF ELECTRIC SHOCK DO NOT OPENN

 

 

 

SHOCK IS RESENT WITH THIS UNIT.

 

 

 

 

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

THIS SYMBOL INDICATES THAT THERE ARE

NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE

IMPORTANT OPERATING AND MAINTENANCE

PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE

INSTRUCTIONS IN THE OWNER’S MANUAL WITH

PERSONNEL.

THIS UNIT.

 

 

 

 

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

IMPORTANT SAFETY INSTRUCTIONS

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with a dry cloth.

7.Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9.Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched, particularly at plugs, convenience

receptacles, and at the point where they exit from the apparatus.

11.Only use the attachments/accessories specified by the manufacturer.

12.Use only with the cart, stand, tripod,

bracket, or table specified by the manufacturer, or sold with the

apparatus. When a cart is used, use caution when moving the cart/

appliance combination to avoid injury from tip-over.

13.Unplug this apparatus during lightning storms or when unused for long periods of time.

14.Refer all servicing to qualified service personnel. Servicing is required when the appliance has been damaged in any way, such as when a power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15.If an outside antenna is connected to the television equipment, be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges. In the U.S. Selection 810-21 of the National Electrical Code provides information with respect to proper grounding of the mast and supporting structure, grounding

of the lead-in wire to an antenna discharge unit, size of grounding conductores, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrodes.

16.An outside antenna system should not be located in the vicinity of overhead power lines or other electrical light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

EXAMPLE OF ANTENNA GROUNDING ACCORDING TO NATIONAL ELECTRICAL CODE, ANSI/NFPA 70

 

ANTENNA LEAD IN WIRE

 

ANTENNA DISCHARGE UNIT

GROUND CLAMP

(NEC SECTION 810-20)

 

GROUNDING CONDUCTORS

 

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

NECNATIONAL ELECTRICAL CODE

NEC ART 250, PART H)

 

” Note to CATV system installer:

This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

17.Wall or Ceiling Mounting - The product should be mounted to a wall or ceiling only as recommended by the manufacturer and listed by an independent laboratory (such as UL).

18.Apparatus shall not be exposed to dripping or splashing and no objects filled with liquides, such as vases, shall be placed on the apparatus.

19.When the MAINS plug is used as the disconnect device, the disconnect device shall remain readily operable.

20.Install the LCD TV in a proper position. If not, it may result in a fire hazard.

21.Provide appropriate space on the top, sides and rear of the LCD TV cabinet for allowing air circulation and cooling the LCD TV.

22.Minimum clearance must be maintained. If the LCD TV is to be built into a compartment or similarly enclosed, the minimum distances must be maintained. Do not cover the ventilation slot on the LCD TV. Heat build-up can reduce the service life of your LCD TV, and can also be dangerous.

2

FCC INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses an can radiate radio frequency energy and, if no installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

CAUTION: FCC Regulations state that improper modifications or unauthorized changes to this unit may void the user’s authority to operate the unit.

ENERGY STAR® User Information

ENERGY STAR User Information Statement: the factory default settings of this television meet ENERGY STAR requirements. Changing Picture Settings may increase energy consumption, possibly beyond the limits required for ENERGY STAR qualification.

To ensure your television is operating at optimal energy efficiency, select default picture mode. Default picture mode is recommended for normal home use.

TRADEMARKS

“As an Energy Star® Partner, Sanyo Manufacturing Corporation has determined that this product meets the Energy Star® guidelines for energy efficiency.”

This symbol on the nameplate means the product is Listed by Underwriters’ Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety standards against risk of fire, casualty and electrical hazards.

PROTECTING THE LCD SCREEN

The screen can be damaged if it is not maintained properly. Do not use hard objects

such as hard cloth or paper. Do not use excessive pressure when cleaning the screen; excessive pressure can cause permanent discoloration or dark spots.

HANDLING PRECAUTIONS

Handle by the cabinet only. Never touch the screen when handling.

Excessive pressure on the scrrn can cause permanent discoloration or dark spots.

Handlingwarranty. damage is not coverded under

NEVER spray liquids on the screen.

CONTANINS MERCURY LAMPS, DISPOSE OF PROPERLY

3

CONTENTS

 

IMPORTANT SAFETY INSTRUCTIONS............

2

FCC INFORMATION............................................

3

ENERGY STAR® USER INFORMATION...........

3

TRADEMARKS.....................................................

3

PROTECTING THE LCD SCREEN.............

3

HANDLING PRECAUTIONS........................

3

ASSEMBLY-ATTACHING THE TV STAND.........

4

INSTALLATION.....................................................

5

POSITIONING THE LCD HDTV...................

5

WALL MOUNTING (OPTIONAL)..................

5

GETTING STARTED............................................

6

RECAUTIONS...............................................

6

GETTING STARTED-CONTROLS

 

AND JACKS............................................

7

REMOTE CONTROL OPERATION.............

8

GETTING STARTED-CONNECTIONS.......

9

POWER CONNECTION.............................

10

GETTING STARTED-POWER

 

CONNECTION/CHANNEL SEARCH..10

INITIAL CHANNEL SCAN...........................

10

ADVANCED AV CONNECTIONS......................

11

ADVANCED DIGITAL SIGNAL

 

CONNECTIONS-HDMI TO HDMI.......

11

DVI TO HDMI...............................................

11

DIGITAL AUDIO...........................................

11

AUDIO OUT JACKS (FIXED ANALOG).....

11

PC CONNECTIONS...........................................

12

PC MONITOR OPERATION.......................

12

SPORTS MODE.................................................

13

ON-SCREEN MENU OPERATION ...........................

14

MENU NAVIGATION MAP..........................

14

CHANNEL ADJUSTMENT..........................

14

CHANNEL LIST OPERATION....................

15

PARENT ADJUSTMENT.............................

16

PICTURE/ AUDIO/ ADVANCED

 

ADJUSTMENT......................................

18

PICTURE.....................................................

18

AUDIO..........................................................

18

ADVANCED.................................................

19

SYSTEM......................................................

21

HELPFUL HINTS - PROBLEMS /

 

SOLUTIONS ...............................................

23

SPECIFICATIONS .............................................

24

CONFIGURATIONS OF VGA TERMINALS ....

25

SIGNAL MODE COLUMN

 

(RECOMMENDED).....................................

26

ASSEMBLY-ATTACHING THE TV STAND

NOTE: Skip this Step if you are wall-mounting the unit.

Tool Needed: Screwdriver remove screws from stand mounting inserts before installing stand base.

For 19”

Padded

Surface

 

For 26” / 32” / 42”

 

Hello! I'm your new Sanyo Widescreen LCD HDTV. Don't plug me in just yet! Please read this manual carefully so you can learn about my many features, such as, my integrated HD Tuner, PARENT control, Digital Channels, my PC Input and many more...

4

INSTALLATION

POSITIONING THE LCD HDTV

Always use a firm-flat surface when positioning your HDTV. Do no position the unit in a

confined area. Allow adequate space for proper ventilation.

19”

18.2

2.5

 

13.8

 

12.5

1.4

 

8.6

6.6

26”

 

26.3

3.6

 

19.5

 

17.7

1.8

 

16

8.3

32”

 

31.6

3.4

 

22.5

 

20.7

1.8

 

16

8.3

42”

 

40.3

3.6

 

 

27.5

 

 

25.6

1.8

19.9

9.9

 

NOTE: All dimensions are in inches.

WALL MOUNTING (OPTIONAL)

Use the screws that are threaded into the standmounting inserts on the back of your HDTV to secure it to a wall mounting kit.

NOTE: 1. Wall Mounting kit is not supplied.

2. Wall mounting kit shall be able to sustain at least 3 times of set weight.

VESA standard interface:

19” TV 100 x 100mm ; 26” TV 100 x 200mm 32” TV 200 x 200mm ; 42” TV 200 x 400mm

Wall Mounting Inserts

Mounting screws measurements: 19” TV

M4 Diameter, Length - 13mm (min.); 16mm (max.)

26” / 32” / 42” TV

M6 Diameter, Length - 13mm (min.); 16mm (max.)

Wall

• (65mm)for 19”

• (60mm)

for 26” / 32” / 42”

5

GETTING STARTED

1 Install supplied batteries in the Remote.

RECAUTIONS

Do not use rechargeables together

with dry cells, other types, mixed new and old, or batteries with different charge levels.

Do not expose the Remote or

batteries to moisture or heat or such as sunshine, fire, or the like.

Match the “+” and “-” signs on the batteries with marks inside the Remote Control.

Please recycle used up rechargeable batteries.

2 Antenna Connection for off-air signals.

ANALOG/DIGITAL

ANTENNA IN

ANTENNA

OR

CABLE

THE TUNER IN THIS HDTV CAN RECEIVE:

a. Digital and Analog off-air signals from an antenna.

OR

b.Analog or Clear QAM cable channels from a direct Cable TV connection.

NOTES:

You must use the on-screen MENU to Search for Clear QAM Cable channels. (see page 13)

For the best picture, connect your Cable box or Satellite receiver to HDMI1, 2, 3 or component (VIDEO3) jacks.

This HDTV can receive ANY unscrambled RF signal being broadcast.

6

GETTING STARTED-CONTROLS AND JACKS

LEFT-SIDE

PANEL

Power key

Channel

keys

Volume _ +keys

Menu key

Input

VIDEO

 

key

 

Video 2 input keys

Component Video Input VIDEO3 (YPbPr), PAGE 9 - Connect digital video equipment to the Video Green (Y), Blue (Pb), Red (Pr) jacks, and matching Audio White (L) and Red (R) jacks. These jacks will automatically detect the type of signal being received.

S-Video Input (VIDEO1), PAGE 9 - To enhance video detail use the S-Video jack instead of the Video jack, if available on your external equipment. (An S-Video connection will override a connection to the Video1 input jack.)

Stereo Audio Out (L/R) Jacks, PAGE 11 - Connect stereo audio equipment to these jacks.

Analog / Digital Antenna Input, PAGE 6 - Connect an RF antenna or Analog Cable system to this jack.

Digital Audio Output (Coaxial), PAGE 11 - Use a Phono-Type (Coaxial) Digital Audio Out Cable to connect Digital Audio Output to an advanced stereo home theater system equipped with Dolby® Digital.

BACK-SIDE

PANEL

AV Input (VIDEO1 or VIDEO2), PAGE 9 - Connect analog video equipment here.

PC Input (15-Pin Monitor and Mini STEREO AUDIO), PAGE 12 - Connect computer and audio outputs to these terminals.

MONITOR RGB (D-SUB)

AUDIO R/L (Stereo Mini Jack)

Service port - For service use only, Used for updating the television’s firmware.

HDMI Input (INPUT1, INPUT2 or INPUT3), PAGE 11 - An all digital AV interface that accepts uncompressed video signals for the very best picture possible. HDMI supports HDCP copy protection, allowing transmission of copy-protected digital content. The signal can also include Dolby® Digital or PCM audio, when available.

7

REMOTE CONTROL OPERATION

MUTE Key - Press to mute or restore the sound.

Number Keys - Press number keys to select a channel.

Example: Press 6 then OK key to select analog channel A6. Press 6 then 1-- key to select digital channel D6.

INPUT Key - Press to select the source to view: TV, VIDEO1, VIDEO2, YPbPr, HDMI1, HDMI2, HDMI3, or PC Input.

SPORTS Key - Press to choose between options Football, Winter Sports, Marine Sports, Indoor Sports, and Off in turn.(See page 13)

ECO Key - Press to Energy saving mode between options Off, ECO1, ECO2, and ECO3 in turn.

Volume Keys - Press VOL - + to decrease or increase the audio volume.

PIX SHAPE Key - Press to choose between options Standard, WaterGlass, Zoom1, Full and Zoom2. Available options depend on the signal and the broadcast’s aspect ratio.

AUDIO Key - Press to select the desired audio mode, if available.

MENU - Press to display on-screen menu.

CURSOR ▲ (up) ▼ (down) keys - Press these

keys to move the cursor up and down.

CURSOR (left) (right) keys - Press these keys to move the cursor left and right.

OK key - Press to select an option from the menu system, when required.

EXIT key - Press to exit from the menu.

1-- Key - Press number key then press this key to select TV digital channel.

GUIDE Key - Press to show window with the guide information displayed on your HDTV screen (digital channel only).

INFO Key - Press to display Channel Banner information.

Digital Banner may contain: Channel Number,

CC State, Channel Title, Video Resolution, Video Ratio, Signal Strength, Digital Sound information & Program Rating.

Analog Banner may contain: Channel Number,

CC State, Channel Title, Video Resolution, Analog Sound information, & Program Rating.

RECALL Key - Press to switch to last channel or input selected.

Channel Up / Down (CH+, _) Keys - Press to switch to last / next active channel.

RESET Key - Press this key to display RESET menu. If execute RESET function, the TV will clear all customized settings.

NOTE : The Channel Scan Memory database will be reset to default (all analog channel enabled), please execute Channel Scan after RESET.

SLEEP Key - Press Press this key to switch Off Timer between Off, 30 min, 60 min, 90 min, 120 min, 150 min and 180 min options.

NOTE : The Off Timer cancels if th eTV is turned off or if a power failure occurs.

CAPTION Key - Press this key to switch CC mode between “Off”, “CC Display” and “Muted=On” options. Digital Captions can be changed using the menu settings.

8

Sanyo LCD-32E3, LCD-42E3, LCD-26E3, LCD-19E3 User Manual

GETTING STARTED-CONNECTIONS

3 Analog Signal Connections - VIDEO1 or VIDEO2 (optional)

Connect an analog device, such as, an Analog Cable Box, Satellite Receiver, or VCR

Composite connectors are included on your new HDTV to provide continued compatibility with older analog devices, such as a VCR. The S-Video connector will provide the best analog resolution. If you have an S-Video connector on your old analog

equipment, you should use it instead of the standard video connector. (Cables are not supplied)

1 Connect an AV cable to the VIDEO1 or VIDEO2 jack on the HDTV and to your analog AV equipment, as shown. Match the connector colors to jack colors.

2 Press the INPUT key to step through the signal inputs to select Video1 or Video2.

DVI

INPUT3 INPUT2 INPUT1

 

PC AUDIO

DIGITAL

 

 

INPUT

AUDIO OUT

 

L

VIDEO

 

 

 

L

 

 

 

R

ANT

ANT

 

 

 

3

VIDEO1 INPUT AUDIO OUT

 

 

INPUT

 

 

ANALOG DEVICE

4 Digital Signal Connections - Video3 (YPbPr)

Connect Digital devices, such as, an HD Cable Box, HD Satellite Receiver, DVD Player, and Game System

The Component jacks on this HDTV will accept HDTV, EDTV, and SDTV video signals, making Component a great choice when connecting your compatible external devices.

1 Connect a COMPONENT cable to a set of Green, Blue, and Red video jacks Video3 (YPbPr) on the HDTV and to your digital device, as shown. (Cable is not supplied)

2 Connect an AUDIO cable to the matching set of White and Red audio jacks, as shown. (Cable is not supplied)

3 Press the INPUT key to step through the signal inputs to select Video3 (YPbPr).

DVI

INPUT3 INPUT2 INPUT1

Pr

 

 

PC AUDIO

DIGITAL

 

L

VIDEO

INPUT

AUDIO OUT

 

 

 

 

R

L

L

 

 

 

R

R

ANT

ANT

 

 

 

VIDEO 3

VIDEO1 INPUT AUDIO OUT

 

 

INPUT

 

 

DVD PLAYER

 

SARELLITE

 

 

 

RECEIVER

INPUT3

INPUT2

INPUT1

DVI

 

 

 

Pr

 

 

 

 

 

 

PC AUDIO

DIGITAL

 

L

VIDEO

INPUT

AUDIO OUT

 

 

 

 

R

L

L

 

 

 

R

R

ANT

ANT

 

 

 

VIDEO 3

VIDEO1 INPUT

 

 

 

INPUT

AUDIO OUT

 

 

9

Loading...
+ 18 hidden pages