00_KHS3682_Cover.fm Page 1 Tuesday, December 15, 2009 10:33 AM
KS3082
KS3682
COOL/DRY Model
INSTRUCTION MANUAL
Inverter-Controlled Split System Air Conditioner
MODE D’EMPLOI
Climatiseur de type séparé contrôlé par inverseur
This air conditioner uses
the new refrigerant R410A.
Save These Instructions!
Conserver ce mode d’emploi
Pub. OI-85264181150000
© SANYO 2010
01_KS3682_EN.fm Page 2 Friday, February 12, 2010 12:26 PM
FEATURES
This air conditioner is an inverter type unit that automatically adjusts capability as appropriate. Details on these functions are provided below; refer to these descriptions when using the air conditioner.
• Microprocessor Controlled Operation
The interior compartment of the remote control unit contains several features to facilitate automatic operation, easy logically displayed for easy use.
• Simple One-touch Wireless Remote Control
The remote control unit has several features to facilitate automatic operation.
• 24-Hour ON or OFF Timer
This timer can be set to automatically turn the unit on or off at any time within a 24 hour period.
• 1-Hour OFF Timer
This timer can be set to automatically turn off the unit at any time after one hour.
• Night Setback
This function saves energy by controlling operation to provide a quieter operating sound than normal.
•Automatic and 3-step Fan Speed
Auto/High/Medium/Low
•Air Sweep Control
This function moves a flap up and down in the air outlet, directing air in a sweeping motion around the room and providing comfort in every corner.
• Auto. Flap Control
This automatically sets the flap to the optimum position during cooling and drying operation.
• Automatic Restart Function for Power Failure
Even when power failure occurs, preset programmed operation can be reactivated once power resumes.
• High Power Operation
The unit operates at maximum output for 30 minutes, regardless of the desired temperature.
The fan speed is 1 step above “High”.
• Quiet Operation
The fan rotates slower than the fan speed setting to provide a quieter operating sound.
• LED Clean Operation
During operation, the UV anti-bacteria unit is activated for 30 minutes and cleans the air blown from the air conditioner.
• Anti-Mold Filter
This unit is equipped with an anti-mold filter that inhibits the growth of mold and bacteria.
• Air Clean Filter
An air filter that eliminates unpleasant odors and cleans the air is available.
Purchase a replacement filter at your local dealer. (model STK-FDXB)
• Unoccupied
This function prevents the room temperature from increasing too much when no one is in the room, and operate automatically to save energy.
CONTENTS |
|
|
|
|
Page |
FEATURES................................................................................. |
2 |
|
PRODUCT INFORMATION ........................................................ |
3 |
|
ALERT SYMBOLS...................................................................... |
3 |
|
INSTALLATION LOCATION........................................................ |
3 |
|
ELECTRICAL REQUIREMENTS ............................................... |
3 |
|
SAFETY INSTRUCTIONS.......................................................... |
3 |
|
NAMES OF PARTS .................................................................... |
4 |
|
USING THE REMOTE CONTROL UNIT.................................... |
8 |
|
OPERATION WITH THE REMOTE CONTROL UNIT ................ |
9 |
|
1. |
Operation .................................................................... |
9 |
2. |
Adjusting the Fan Speed ............................................. |
9 |
3. |
Fan Only...................................................................... |
9 |
4. |
Night Setback Mode.................................................. |
10 |
5. QUIET Mode ............................................................. |
10 |
|
6. HIGH POWER Mode................................................. |
10 |
|
7. LED CLEAN Mode .................................................... |
11 |
|
8. UNOCCUPIED Mode ................................................ |
11 |
|
Page |
SPECIAL REMARKS ................................................................ |
12 |
SETTING THE TIMER .............................................................. |
12 |
USING THE 1-HOUR OFF TIMER ........................................... |
14 |
TIPS FOR ENERGY SAVING ................................................... |
14 |
ADJUSTING THE AIRFLOW DIRECTION ............................... |
14 |
OPERATION WITHOUT THE REMOTE CONTROL UNIT ....... |
15 |
CARE AND CLEANING ............................................................ |
15 |
TROUBLESHOOTING .............................................................. |
17 |
OPERATING RANGE................................................................ |
17 |
WIRED REMOTE CONTROLLER ............................................ |
17 |
2 |
OI-150-2-EG |
|
01_KS3682_EN.fm Page 3 Friday, February 12, 2010 12:26 PM
PRODUCT INFORMATION
If you have problems or questions concerning your Air Conditioner, you will need the following information. Model and serial numbers are on the nameplate on the bottom of the cabinet.
Model No. __________________________________
Serial No. ___________________________________
Date of purchase _____________________________
Dealer’s address _____________________________
Phone number ________________
ALERT SYMBOLS
The following symbols used in this manual, alert you to potentially dangerous conditions to users, service personnel or the appliance:
This symbol refers to a hazard or unsafe practice which can result in severe personal injury or death.
This symbol refers to a hazard or unsafe CAUTION practice which can result in personal
injury or product or property damage.
INSTALLATION LOCATION
•We recommend that this air conditioner be installed properly by qualified installation technicians in accordance with the Installation Instructions provided with the unit.
•Before installation, check that the voltage of the electric supply in your home or office is the same as the voltage shown on the nameplate.
•Do not install this air conditioner where there are fumes or flammable
gases, or in an extremely humid space such as a greenhouse.
•Do not install the air conditioner where excessively high heat-generating objects are placed.
Avoid:
To protect the air conditioner from heavy corrosion, avoid installing the outdoor unit where salty sea water can splash directly onto it or in sulphurous air near a spa.
OI-150-3-EG
ELECTRICAL REQUIREMENTS
1.All wiring must conform to the local electrical codes. Consult your dealer or a qualified electrician for details.
2.Each unit must be properly grounded with a ground (or earth) wire or through the supply wiring.
3.Wiring must be done by a qualified electrician.
SAFETY INSTRUCTIONS
•Read this Instruction Manual carefully before using this air conditioner. If you still have any difficulties or problems, consult your dealer for help.
•This air conditioner is designed to give you comfortable room conditions. Use this only for its intended purpose as described in this Instruction Manual.
•Never use or store gasoline or other
flammable vapor or liquid near the air conditioner — it is very dangerous.
• This air conditioner has no ventilator for intaking fresh air from outdoors. You must open doors or windows frequently when you use gas or oil heating appliances in the same room, which consume a lot of oxygen from the air. Otherwise there is a risk of suffocation in an extreme case.
|
|
• |
Do not turn the air conditioner on and |
CAUTION |
|
||
|
|
off from the power mains switch. Use |
|
|
|
|
|
|
|
|
the ON/OFF operation button. |
|
|
• Do not stick anything into the air outlet |
|
|
|
|
of the outdoor unit. This is dangerous |
|
|
|
because the fan is rotating at high |
|
|
|
speed. |
|
|
• |
Do not let children play with the air |
|
|
|
conditioner. |
|
|
• |
Do not cool the room too much if |
|
|
|
babies or invalids are present. |
|
|
|
|
3
01_KS3682_EN.fm Page 4 Friday, February 12, 2010 12:26 PM
NAMES OF PARTS
Air intakes
INDOOR UNIT
Air outlet
Remote control unit
Drain hose
Refrigerant tubes
OUTDOOR UNIT
Air outlet
NOTE
This illustration is based on the external view of a standard model. Consequently, the shape may differ from that of the air conditioner which you have selected.
This air conditioner consists of an indoor unit and an outdoor unit. You can control the air conditioner with the remote control unit.
Air Intake |
Air from the room is drawn into this section and |
|
passes through air filters which remove dust. |
|
|
Air Outlet |
Conditioned air is blown out of the air |
|
conditioner through the air outlet. |
|
|
Remote |
The wireless remote control unit controls power |
Control Unit |
ON/OFF, operation mode selection, |
|
temperature, fan speed, timer setting, and air |
|
sweeping. |
|
|
Refrigerant |
The indoor and outdoor units are connected by |
Tubes |
copper tubes through which refrigerant gas |
|
flows. |
|
|
Drain Hose |
Moisture in the room condenses and drains off |
|
through this hose. |
|
|
Outdoor |
The outdoor unit contains the compressor, fan |
(Condensing) |
motor, heat exchanger coil, and other electrical |
Unit |
components. |
|
|
|
|
UNIT DISPLAY AND OPERATION BUTTON
INDOOR UNIT
OPERATION lamp
TIMER lamp
REMOTE CONTROL receiver
OPERATION button LED CLEAN lamp (ON/OFF)
IMPORTANT
Avoid using radio equipment such as mobile phone near (within 4 ft. (1.2 m)) the remote control receiver. Some radio equipment may cause malfunction of the unit.
If the trouble happens, disconnect power and restart the air conditioner after a few minutes.
REMOTE |
This section picks up infrared signals from the |
||
CONTROL |
remote control unit (transmitter). |
|
|
receiver |
|
|
|
|
|
|
|
OPERATION |
When the remote control unit cannot be used, |
||
button |
pressing this button enables cooling operation. |
||
|
Each time this button is pressed, the operation |
||
|
mode changes cyclically. |
|
|
|
Cooling operation |
|
Stop |
|
|
||
|
|
|
|
OPERATION |
This lamp lights when the system is in the |
||
lamp |
continuous DRY (orange), COOL (green) and |
||
|
FAN (green) mode. |
|
|
|
|
|
|
TIMER lamp |
This lamp lights when the system is being |
||
|
controlled by the timer. |
|
|
|
|
|
|
LED CLEAN |
This lamp lights during operation in the UV anti- |
||
lamp |
bacterial mode. |
|
|
|
|
|
|
NOTE
The unit’s display lamps are dimmed during operation in the NIGHT SETBACK mode.
4 |
OI-150-4-EG |
|
01_KS3682_EN.fm Page 5 Friday, February 12, 2010 12:26 PM
REMOTE CONTROL UNIT (DISPLAY)
Displayed when transmitting data
Displayed when setting temperature
Displayed when indoor unit sensor is in use
Displayed when temperature is shown
Displayed when setting timer
Symbols
(1)Operation mode
MILD DRY ..............................
COOL .....................................
FAN ........................................
(2)Fan speed
Automatic operation ...............
HIGH .....................................
MEDIUM.................................
LOW .......................................
(3)Temperature setting 60 – 86 °F
When set to 80 °F temperature indication............
(4)Timer
24-hour clock with ON/OFF program Timer .......................
ON Timer. ..............................
OFF Timer. ............................
1-hour OFF Timer. .................
(5)NIGHT SETBACK..................
(6)Confirmation of transmission.......
(7)Auto. flap indication................
Flap angle indication..............
Sweep indication....................
(8)High power operation.............
(9)UNOCCUPIED ......................
(10)Quiet operation ....................
(11)LED CLEAN operation.........
OI-150-5-EG |
5 |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
01_KS3682_EN.fm Page 6 Friday, February 12, 2010 12:26 PM
REMOTE CONTROL UNIT
Transmitter
When you press the buttons on the remote control unit, the mark appears in the display to transmit the setting changes to the receiver in the air conditioner.
Display
Information on the operating conditions is displayed while the remote control unit is switched on. If the unit is turned off, FLAP setting and FAN SPEED setting are not displayed.
LED CLEAN button
: If this button is pressed during DRY, COOL or FAN operation, the UV anti-bacterial unit is activated for 30 minutes and cleans the air blown from the air conditioner.
QUIET button
: When you press this button, the fan rotates slower than the fan speed setting to provide a quieter operating sound.
FAN SPEED selector button
: The air conditioner automatically decides the fan speeds.
: High fan speed
: Medium fan speed : Low fan speed
FLAP button
Press this button either to select the setting of the airflow direction to the auto. flap in each mode or one of the six possible positions manually or to select the sweep function which moves the flap up and down automatically. : Auto flap setting: If selected in a cooling or dry operation, the flap is
set at position (7) in the following chart.
: The airflow direction can be set manually. (six positions) : The flap moves up and down automatically.
NOTE
When you press the FLAP button, the air flow direction will be changed one by one as follows.
SWEEP
ON TIME/OFF TIME setting buttons Advance button
Return button
No display: The timer does not operate.
: The air conditioner starts at the set time.
: The air conditioner stops at the set time.
: The air conditioner stops and starts, or starts and stops, at the set times every day. For details, see “SETTING THE TIMER”.
CANCEL button
SENSOR button
When you press this button (use a small-tipped object such as a ballpoint pen), the mark will appear at the display. And the room temperature is detected by the
sensor which is built into the indoor unit and the air conditioner is controlled accordingly.
NOTE
If the remote control unit is located near a heat source, such as a space heater or in direct sunlight, press the SENSOR button to switch to the sensor on the indoor unit.
ADDRESS switch |
|
Temperature display selector button |
|
•The address switch changes to prevent mixing of signals from remote control units when two air conditioners are installed next to each other. Normally, the address switch is set to A. For more information, please contact the dealer where you made the purchase.
•Normally, the tabs on the remote control unit should not be bent.
This switches the temperature display between °C and °F.
6 |
OI-150-6-EG |
|
01_KS3682_EN.fm Page 7 Friday, February 12, 2010 12:26 PM
Sensor
A temperature sensor inside the remote control unit senses the room temperature.
ON/OFF operation button
This button is for turning the air conditioner on and off.
1 HR. TIMER button (1-HOUR OFF TIMER)
: When you press this button, regardless of whether the unit is operating or stopping, the unit operates for one hour and then shuts down.
Temperature setting buttons (TEMP.)
Press the |
button to increase the set temperature. |
Press the |
button to reduce the set temperature. |
The temperature setting changes by 1 °C or 2 °F each time one of the TEMP. buttons is pressed.
MODE selector button
Use this button to select DRY, COOL or FAN mode.
(DRY) |
: The air conditioner reduces the humidity in the room. |
(COOL) : The air conditioner makes the room cooler.
(FAN) |
: The air conditioner works only as a circulation fan. |
NIGHT SETBACK button
For details, see “4. Night Setback Mode”. When you press this button in the DRY or COOL mode, the mark appears in the display, and the remote control unit will automatically adjust the set temperature to save energy.
HIGH POWER button
: If this button is pressed during DRY, COOL or FAN operation, the unit operates at maximum output for 30 minutes, regardless of the desired temperature.
The fan speed is 1step above ‘‘HIGH’’.
CLOCK button
UNOCCUPIED button
For details, see “8. UNOCCUPIED Mode”. When you press this button, the mark appears in the display. And the remote control unit will automatically prevent the room temperature from increasing too much when no one is in the room.
ACL button (ALL CLEAR)
Puts the remote control unit into pre-operation status. Always press this button after replacing the batteries.
NOTE |
(Cover closed) |
|
|
•The illustration above pictures the remote control unit after the cover has been opened.
•The remote control unit sends the temperature signal to the air conditioner regularly at five minute intervals. If the signal from the remote control unit stops for more than 15 minutes due to the loss of the remote control unit or other trouble, the air conditioner will switch to the temperature sensor which is built into the indoor unit and control the room temperature. In these cases, the temperature around the remote control unit may differ from the temperature detected at the air conditioner’s position.
•The indoor fan runs continuously when the system is in normal operation. It does not turn off when the desired room temperature is reached. If Night Set Back mode is selected, the fan will turn off intermittently during cooling operation in order to control air flow.
OI-150-7-EG |
7 |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
01_KS3682_EN.fm Page 8 Friday, February 12, 2010 12:26 PM
USING THE REMOTE CONTROL UNIT
HOW TO INSTALL BATTERIES
ACL button
1.Slide the cover in the direction indicated by the arrow and remove it.
2.Install two AAA alkaline batteries. Make sure the batteries point in the direction marked in the battery compartment.
3.Use a thin object such as the tip of a pen to press the ACL button.
NOTE
•The batteries last about six months, depending on how much you use the remote control unit. Replace the batteries when the remote control unit’s display fails to light, or when the remote control unit cannot be used to change the air conditioner’s settings.
•Use two fresh leak-proof type-AAA alkaline batteries.
•In replacing batteries, follow the instructions as mentioned in the sub-section “HOW TO INSTALL BATTERIES”.
•If you do not use the remote control unit more than 1 month, take out the batteries.
•Dispose of the used batteries at the designated location in compliance with the applicable local ordinances.
HOW TO USE THE REMOTE CONTROL UNIT
When using the remote control unit, always point the unit’s transmitter head directly at the air conditioner’s receiver.
Air conditioner (Indoor unit)
Receiver
Remote control unit |
(Transmitter head) |
|
REMOTE CONTROL UNIT INSTALLATION POSITION
The remote control unit may be operated either from a non-fixed position or from a wall-mounted position. To ensure that the air conditioner operates correctly, DO NOT install the remote control unit in the following places:
DO NOT
•In direct sunlight
•Behind a curtain or other places where it is covered
•More than 26 ft.(8 m) away from the air conditioner
•In the path of the air conditioner’s airstream
•Where it may become extremely hot or cold
•Where it may be subject to electrical or magnetic noise
•Where there is an obstacle between the remote control unit and air conditioner (since a check signal is sent from the remote control unit every 5 minutes)
MOUNTING THE REMOTE CONTROL UNIT
Before mounting the remote control unit, press the ON/OFF operation button at the mounting location to make sure that the air conditioner operates from that location. The indoor unit should make a beeping sound to indicate that it has received the signal.
Rear side
Remote control unit mount
|
Press |
|
|
|
Set in |
Hole |
|
|
place |
||
|
|
||
Mounting screws |
|
|
|
5/32 x 5/8" |
• To prevent loss of the remote control |
||
(4 x 16 mm) |
|||
unit, you can connect the remote |
|||
(included) |
|||
control unit to the mount by passing |
a string through the remote control unit and attachment hole.
To take out the remote control unit, pull it forward.
WHEN HOLDING THE REMOTE CONTROL UNIT
•When using the remote control unit and during air conditioner operation, the transmitter on the remote control unit should be pointed towards the receiver on the indoor unit.
•Make sure that there are no objects between the remote control unit and receiver which could block the signal.
8 |
OI-150-8-EG |
|
01_KS3682_EN.fm Page 9 Friday, February 12, 2010 12:26 PM
OPERATION WITH THE REMOTE CONTROL UNIT
1. Operation
STEP 2
STEP 3
STEP 1
STEP 4
STEP 5
NOTE Check that the circuit breaker on the power panel is turned on.
Press the setting buttons as described below and change the settings as desired.
STEP 1 Press the MODE selector button |
|
|
and select the desired mode. |
→ |
|
For dehumidifying operation |
|
|
For cooling operation |
→ |
|
|
||
For fan only operation |
→ |
|
|
STEP 2 To start the air conditioner, press the ON/ OFF operation button.
STEP 3 Press the TEMP. setting buttons to change the temperature setting to the desired temperature.
Adjustable temperature range:
30 |
°C max. |
or 86 |
°F max. |
16 |
°C min. |
60 |
°F min. |
STEP 4 Set the FAN SPEED selector button to the setting you want.
STEP 5 Press the FLAP button and set the airflow direction as desired.
(Refer to “ADJUSTING THE AIRFLOW DIRECTION” on page 14.)
To stop the air conditioner, press the ON/OFF operation button again.
NOTE • Choose the best position in the room for the remote control unit, which also acts as the sensor for room comfort and transmits the operating instructions.
Once you’ve found this best position, always keep the remote control unit there.
•This appliance has a built-in 5-minute time delay circuit to ensure reliable operation. When the operation button is pressed, the compressor will start running within three minutes. In the event of power failure, the unit will stop.
2. Adjusting the Fan Speed
A. Automatic fan speed
Simply set the FAN SPEED selector button to the position.
This automatically sets the best fan speed for the room temperature.
B. Manual fan speed
If you want to adjust fan speed manually during operation, just set the FAN SPEED selector button as desired. [,
, or ]
3. Fan Only
STEP 2
STEP 1
STEP 3
If you want to circulate air without any temperature control, follow these steps:
STEP 1 Press the MODE selector button to switch to the fan mode .
STEP 2 Press the ON/OFF operation button.
STEP 3 Press the FAN SPEED selector button to select the fan speed of your choice (, or ).
OI-150-9-EG |
9 |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
01_KS3682_EN.fm Page 10 Friday, February 12, 2010 12:26 PM
4. Night Setback Mode
Night Setback Mode is used for saving energy.
Press the NIGHT SETBACK button while operation. (except FAN mode)
The mark appears in the display.
To release the night setback function, press the NIGHT SETBACK button again.
NOTE
Pressing the MODE selector button cancels Night Setback mode.
In Cooling and DRY Mode: ( and )
When the night setback mode is selected, the air conditioner automatically raises the temperature setting 2 °F when 30 minutes have passed after the selection was made, and then another 2 °F after another 30 minutes have passed, regardless of the indoor temperature when night setback was selected. This enables you to save energy without sacrificing comfort. This function is convenient when gentle cooling is needed.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Setting |
|
|
|
|
|
|
|
2 °F |
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
temperature |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2 °F |
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
30 |
|
min. |
||||||
Press the NIGHT |
|
|
30 min. |
|
||||||||||||
|
|
|
|
|
|
|
|
|
|
|
Time |
SETBACK button
5. QUIET Mode
QUIET Mode is used to reduce the fan sound of the indoor unit.
Press the QUIET button.
The mark appears in the display.
To cancel, press QUIET button again.
•In QUIET Mode, the fan rotates at a slower speed than the fan speed setting.
•If the unit is already operating with a very low airflow, the fan sound may not change even if the QUIET button is pressed.
6. HIGH POWER Mode
HIGH POWER mode can be used to increase the output of the indoor unit for all operation modes.
Press the HIGH POWER button while operation.
The mark appears in the display.
To cancel, press HIGH POWER button again.
•When the HIGH POWER button is pressed, the unit operates at maximum output for 30 minutes, regardless of the desired temperature. The fan speed is 1 step above “High”.
•QUIET Mode and HIGH POWER Mode cannot be used at the same time.
NOTE
•Pressing the MODE selector button cancels HIGH POWER mode.
•Depending on the operating conditions, the fan speed may be increased by a small amount only.
10 |
OI-150-10-EG |
|
01_KS3682_EN.fm Page 11 Friday, February 12, 2010 12:26 PM
7. LED CLEAN Mode
In LED CLEAN mode, a UV anti-bacterial unit (including a LED CLEAN lamp and anti-bacterial filter) in the indoor unit is used during DRY, COOL, or FAN operation to remove bacteria from air blown from the air conditioner.
Press the LED CLEAN button while operation.
The mark appears in the display.
To cancel, press the LED CLEAN button again.
•When the LED CLEAN button is pressed, the UV anti-bacterial unit operates for one hour and cleans air blown from the air conditioner.
NOTE
•Pressing the MODE selector button cancels LED CLEAN mode.
•Do not open the front panel while the LED CLEAN lamp on the display is on.
•Depending on the room brightness, light from the LED CLEAN lamp may reflect inside the air conditioner and be visible. This is not a malfunction.
8. UNOCCUPIED Mode
Unoccupied mode is used to prevent the room temperature from increasing too much when no one is in the room, and operate automatically to save energy.
Press the UNOCCUPIED button. The mark appears in the display.
To release the unoccupied function, press the UNOCCUPIED button again.
Unoccupied Indication
Unoccupied |
Unoccupied |
Status |
|
Function |
Indication |
||
|
|||
|
|
|
|
OFF |
no display |
The unoccupied function is not set. |
|
|
|
|
|
|
|
The unoccupied function is now |
|
|
|
being set, and under Cooling |
|
|
flashing |
operation. |
|
ON |
|
||
|
|
||
|
Although the unoccupied function is |
||
|
|
||
|
|
set, not under Cooling operation. |
|
|
lighting |
|
|
|
|
|
NOTE
Even if Unoccupied Mode is ON, it will be disabled if the air conditioner is in operation.
•Unoccupied Function can be set and released through all operational modes, regardless of whether the air conditioner is operating or not.
•If the Unoccupied Function is ON and the remote control unit is used to turn the air conditioner OFF (including OFF TIMER), the air conditioner will turn off, but depending on the room temperature, Cooling Operation will automatically begin.
•When the Unoccupied Function is in operation and the ON/OFF operation button is pressed, operation will restart based on the settings input before the air conditioner was turned off.
In Cooling Mode: ( )
(1)When the room temperature rises above 89°F, Cooling Operation will begin.
(2)When the room temperature drops below 82°F, Cooling Operation will stop.
The above actions will repeat so that the room temperature is maintained at about 86°F.
Room
Temperature (°F) (1)
89
86 |
|
|
|
|
|
|
|
82 |
|
|
|
|
(2) |
|
|
|
|
|
|
|
Cooling |
Time |
|
|
Cooling |
||
|
starts |
stops |
•Unoccupied Mode triggers Cooling Operation in response to the room temperature, but when this happens, the remote control unit will continue to display the Operation mode set by the user.
•If the room temperature rapidly changes, the room temperature may get over the upper or lower limit when the unoccupied function is activated.
NOTE
•The remote control unit should be used in the location specified in “REMOTE CONTROL UNIT INSTALLATION POSITION” on
page 8.
•The air conditioner’s stop order (stated in (2) / above) is valid only when the unoccupied function is operated.
OI-150-11-EG |
11 |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|