Page 1
USER AND MAINTENANCE MANUAL
IMPORTANT: documents included in this manual to be kept:
• "CE" COMPLIANCE DECLARATION
• WARRANTY CERTIFICATE
Translation of the original version
Read the instructions for use before unpacking the appliance.
Coffee grinders - Fruit squeezers - Mixers - Blenders - Drinks dispensers - Mixer beaters - Dough mixer Cheese graters - Ice crushers - Mincers - Vegetable cutters
INTERNATIONALLY PATENTED MODELS
SANTOS SAS :
140-150 AVENUE ROGER SALENGRO
69120 VAULX-EN-VELIN (LYON) - FRANCE
TÉL. 33 (0) 472 37 35 29 - FAX 33 (0) 478 26 58 21
E-Mail :santos@santos.fr www.santos.fr
BRUSHLESS BLENDER N°62
!
Page 2
SANTOS: User and maintenance manual
98162 EN 1.5 - 02 2014 2 / 23 www.santos.fr
CONTENTS
“CE” COMPLIANCE DECLARATION..................................................................................................................................................................... 3
SAFETY RULES ........................................................................................................................................................................................................... 4
DO NOT: ................................................................................................................................................................................................................... 4
ELECTRICAL CONNECTION: ................................................................................................................................................................................. 5
1st TIME USE ............................................................................................................................................................................................................ 5
RECYCLING THE PRODUCT AT THE END OF ITS SERVICE LIFE ..................................................................................................................... 5
DESCRIPTION OF THE APPLIANCE ...................................................................................................................................................................... 6
INSTALLATION AND HANDLING ........................................................................................................................................................................... 6
Installation on a counter ....................................................................................................................................................................................... 6
Installation when built into the countertop ........................................................................................................................................................... 6
USING THE APPLIANCE ........................................................................................................................................................................................... 8
CONTROL PANEL DESCRIPTION .......................................................................................................................................................................... 8
USE ........................................................................................................................................................................................................................... 8
Starting up ........................................................................................................................................................................................................... 8
Stopping the appliance: ........................................................................................................................................................................................ 8
Cycle counter ....................................................................................................................................................................................................... 9
PRE-RECORDED RECIPES ..................................................................................................................................................................................... 9
Selecting a pre-recorded menu ............................................................................................................................................................................. 9
Custom menu ..................................................................................................................................................................................................... 10
CREATING CUSTOM RECIPES ............................................................................................................................................................................. 10
Creating custom recipes ..................................................................................................................................................................................... 10
CLEANING: ............................................................................................................................................................................................................ 11
Cleaning the jar: ................................................................................................................................................................................................. 11
Sanitizing the jar: ............................................................................................................................................................................................... 11
HOOD SAFETY FEATURE ..................................................................................................................................................................................... 12
Modifying the safety mode connected with the hood lid .................................................................................................................................... 12
MAINTENANCE ...................................................................................................................................................................................................... 12
Spare parts: ........................................................................................................................................................................................................ 12
Changing the drive system: ................................................................................................................................................................................ 12
Changing the blade: ........................................................................................................................................................................................... 13
FAULT FINDING ....................................................................................................................................................................................................... 15
The appliance will not start: ............................................................................................................................................................................... 15
The blade does not rotate ................................................................................................................................................................................... 16
The appliance stops as a result of an overload ................................................................................................................................................... 16
The appliance stops further to an overload "OVERLOAD": .............................................................................................................................. 16
The appliance resets while it is operating: ......................................................................................................................................................... 16
Noises, vibrations, leaks at jar blade level ......................................................................................................................................................... 16
Problem with the recipes .................................................................................................................................................................................... 17
APPLIANCE TECHNICAL SPECIFI CATIONS ..................................................................................................................................................... 18
TECHNICAL SPECIFICATIONS ............................................................................................................................................................................ 18
Wiring diagram 110-120V 50/60Hz and 220-240V 50/60Hz ................................................................................................................................. 19
Element cross-reference table
................................................................................................................................................................................ 20
Simplified list of appliance codes
.......................................................................................................................................................................... 20
WARRANTY CERTIFICATE
................................................................................................................................................................................. 23
APPLIANCE IDENTIFICATION PLATE
............................................................................................................................................................ 23
Page 3
SANTOS: User and maintenance manual
98162 EN 1.5 - 02 2014 3 / 23 www.santos.fr
“CE” COMPLIANCE DECLARATION
THE MANUFACTURER:
SANTOS SAS - 140-150, Av. Roger SALENGRO 69120 VAULX-EN-VELIN (LYON)
FRANCE
declares that the appliance intended for the professional market described below:
Description: BRUSHLESS BLENDER
Type number: 62
complies with:
• the statutory provisions defined in appendix 1 of the European "machines" directive
n°2006/42/CE and the national legislation transposing it
• the statutory provisions of the following European directives and regulations:
o N° 2006/95/CE (low voltage directive)
o N° 2004/108/CE (EMC directive)
o No. 2002/95/CE (RoHS directive)
o No. 2002/96/CE (WEEE directive)
o N° 1935/2004/CE (regulation) relating to materials and articles intended to
come into contact with foodstuffs
Harmonised European standards used to give presumption of conformity with the essential
requirements of the above-mentioned directives:
• NF EN 12852+A1: 2010, Food processing machinery – Food preparation
equipment and blenders - Safety and hygiene requirements.
This European standard is a type-C standard as defined in EN ISO 12100. When the provisions of
this type-C standard differ from those stated in the type-A or B standards, the provisions of the typeC standard override the provisions of the other standards. This standard provides the means to
comply with the requirements of the "machines" directive n°2006/42/CE, (see appendix ZA)
• NF EN ISO 12100 -1 and 2:2004: Safety of machinery - General principles for
design
• NF EN 60204-1: 2006 : Safety of machinery - Electrical equipment of machinesGeneral requirements
• NF EN 1672-2: 2005, Food processing machinery – Basic concepts – Hygiene
requirements
• NF EN 60335-1: 2013 : Household and similar electrical appliances. Safety.
• NF EN 60335-2-64 :2004 : Particular requirements for commercial electric kitchen
machines
Drawn up in VAULX-EN-VELIN on: 01/02/2014
Signatory’s position: CHIEF EXECUTIVE OFFICER
Signatory’s name: Aurélien FOUQUET
Signature:
Page 4
SANTOS: User and maintenance manual
98162 EN 1.5 - 02 2014 4 / 23 www.santos.fr
SAFETY RULES
At the time of use, maintenance or scrapping of the appliance, always ensure that the
following elementary precautions are adhered to.
Read the explanatory instructions in full
Keep this user manual
DO NOT:
1. Use this appliance to process anything other than foodstuffs.
2. Pass the pits through the appliance. Remove the pits from fruits before
passing them in the appliance (e.g. mangos, apricots, peaches).
3. Use the appliance without first correctly installing the jar (1) fitted with its lid
(2) on the motor base (3).
4. Operate the appliance without any food in the jar.
5. Fill the jar beyond the maximum capacity corresponding to the amount
marked on the side: 1.4 liters. The maximum capacity must be reduced for
thick mixtures.
6. The base (6) must not be immersed in water.
7. Plunge the base in water or any other liquid for reasons of protection against
risks of electrocution.
8. use the unit with a damaged power cord. it must be replaced by an
authorized dealer or by SANTOS company, or by similarly qualified persons
in order to avoid a hazard.
9. The appliance must be unplugged before any intervention on it: cleaning,
general care, maintenance.
10. Use a hose nor a pressure hose for cleaning: this is forbidden
11. Use an abrasive sponge to clean the plastic jar (1).
12. Insert or store kitchen utensils in the jar.
13. Operate the appliance if the jar or a blade is chipped, cracked or broken.
Never use a jar if there is any play with respect to the blade.
14. It is forbidden to operate the appliance on a surface with a slope in excess of
10° relative to the horizontal plane. All 4 feet of the appliance must always
be resting on this surface. The appliance motor shaft must always be vertical
relative to the surface on which it is placed.
15. Use of spare parts other than certified original SANTOS parts is prohibited
16. Turn the On/Off switch (4) to "0" when the appliance is not operating.
17. Connect several appliances to the same power socket.
18. Use the appliance outdoors.
19. Never place the appliance close to or on a source of heat.
20. This appliance is a professional machine designed exclusively for
Note: You will find it easier to understand the next few paragraphs if you refer to
the diagrams at the end of this manual
!
Page 5
SANTOS: User and maintenance manual
98162 EN 1.5 - 02 2014 5 / 23 www.santos.fr
professional use. It is not designed for household use.
21. This appliance is not designed for use by people (including children) whose
physical, sensorial or mental capacities are impaired or by people with no
experience or knowledge, unless they have been supervised or given
training in the use of the appliance beforehand by a person responsible for
their safety.
Supervise children to ensure they do not play with the appliance.
ELECTRICAL CONNECTION:
• The appliance's power supply is available in two single-phase voltages:
- 110-120 V 50/60 Hz:
- 220-240 V 50/60 Hz:
Line protection: the appliance must be connected to a standard 2 pole + ground socket.
The set-up must be fitted with a differential circuit breaker and a 16A fuse. Grounding of
the appliance is compulsory.
TAKE CARE:
Before connecting the appliance, check that the mains electrical voltage is the
same as the voltage for your appliance. Its value is shown:
either on the identification plate under the appliance.
or on the identification plate on the last page of this manual.
TAKE CARE: Check that the on / off switch (4) is in position “0-Off” before
plugging the power cord in to the mains power socket.
1st TIME USE
Thoroughly clean all parts in contact with the food. jar (1) lid (2).
See the "cleaning" chapter.
RECYCLING THE PRODUCT AT THE END OF ITS SERVICE LIFE
This appliance is marked with the symbol of the selective waste sorting
system relating to waste electrical and electronic equipment. This means
that the product must be disposed of via a selective waste sorting system in
accordance with directive 2002/96/CE (DEEE) – Professional Appliances
section – so that it can be either recycled or dismantled in order to reduce
any impact on the environment.
For further information you can contact your dealer or SANTOS.
For the disposal or recycling of the appliance components, please refer to a specialist
company or contact SANTOS.
Electronic products not covered by a selective sorting system are potentially dangerous for
the environment.
The packaging material should be disposed of or recycled in accordance with regulations
!
!
Page 6
SANTOS: User and maintenance manual
98162 EN 1.5 - 02 2014 6 / 23 www.santos.fr
in force.
Table showing the proportions of materials making up the appliance (percentage weight)
Total steel
Total
aluminum
Total plastic Total copper
Miscellaneous
materials*
31.1%
19.0%
33.2%
2.8%
13.8%
* Weight of miscellaneous materials, e.g. : switches, electronic boards, capacitors, electric cables, etc
DESCRIPTION OF THE APPLIANCE
• Appliance n° 62 is a professional appliance designed exclusively for professional
use. It is not designed for household use.
• Appliance n° 62 is made for the preparation of cocktails, smoothies and all types of
preparation based on crushed ice and blended fruit which may be produced in bars,
cafés, hotels or restaurants.
• The appliance consists of a blender jar, a motor base fitted with an On/Off switch, an
electronic module, a control panel and a sound-proofing hood.
• Some thirty recipes show how to prepare most of the desired preparations.
• The appliance has a USB Host connection allowing 6 custom recipes to be updated,
along with the appliance's Firmware.
INSTALLATION AND HANDLING
Check that the power outlet plug is always easily accessible whatever the installation
mode (counter version or enclosed version)
Installation on a counter
The appliance can be handled by a single person. For ease of use, it is recommended that
the appliance is placed on a table or work surface so as to have the control panel in front
of you (recommended height: 90 cm, to be adapted as required for the user).
Installation when built into the countertop
Before cutting out the countertop, check the following points in order to be sure that the
appliance will be perfectly usable once built-in:
Page 7
SANTOS: User and maintenance manual
98162 EN 1.5 - 02 2014 7 / 23 www.santos.fr
Make sure there is sufficient clearance (behind, above, below) for proper installation and
operation of the appliance.
The cut-out in the countertop represents a rectangle measuring 168mm x 198mm.
• Make sure there is a minimum clearance of 135mm beneath the countertop
• The free space above must measure at least 495mm
• The minimum clearance to the rear must be 102mm (distance between the cut-out
and the wall)
• The minimum clearance sideways must be 30mm
Multiple cut-outs.
It is recommended to leave a distance of 100mm between 2 cut-outs.
Adapting the appliance to use it as a built-in version.
• Disconnect the appliance from the mains.
• Remove the jar (1) and hood lid (8)
• Tip the appliance backwards
• Using a Torx screwdriver, remove the 3 screws located between the metal casing
and motor surround (6).
• Remove the motor surround (6)
Page 8
SANTOS: User and maintenance manual
98162 EN 1.5 - 02 2014 8 / 23 www.santos.fr
USING THE APPLIANCE
CONTROL PANEL DESCRIPTION
The control panel (5) is made up of:
• a graphic screen (22),
• 6 "recipe" keys (23) including one P for "pulse".
Each key corresponds to a predefined recipe.
USE
Note: the appliance will not start unless the hood lid (8) is closed.
Starting up
1. Power up the appliance by putting the On/Off switch (4) to position 1.
2. Put soft foods in the jar (1) first followed by the harder ones, with ice cubes last of
all. Using pieces of food of even size make the recipe easier to carry out.
3. Put the lid (2) on the jar and check it is correctly
positioned.
4. Make sure the motor is turned off, then install the jar
on the jar mat (9).
5. Close the sound-proofing hood by lowering the lid
(8). The LCD screen should show: "READY"
6. Press one of the 6 keys (23) to start the cycle for the
corresponding recipe.
7. The lamp for the key activated will remain lit while
the cycle is in progress.
8. Wait for the cycle to end.
Stopping the appliance:
The appliance will stop either:
• Automatically at the end of the cycle
• Or by manual intervention, by pressing one of the 6 keys on the control panel or by
putting the switch to (0)
Note: opening the sound-proofing hood will trigger the
"pause" mode. The motor will stop. When the soundproofing hood is closed again, the cycle starts up again from
where it stopped, unless the hood remains open for more
than 30 seconds.
Page 9
SANTOS: User and maintenance manual
98162 EN 1.5 - 02 2014 9 / 23 www.santos.fr
Cycle counter
The stop function has a partial cycle counter which allows the number of recipes carried
out over a given period to be counted:
This code: "4 – 5 – 2" is used to view the counter,
• Hit the 1 key to reset the counter to zero while viewing it.
PRE-RECORDED RECIPES
The appliance is delivered with 3 basic menus loaded as standard, each containing
consisting of 6 recipes among the 30 recipes pre-recorded in the appliance.
• "Universal menu" which allows most recipes usually needed to be carried out
• "Coffee shop menu" which is more suited to coffee shops
• "Juice bar menu" which is more suited to juice bars.
Note: Each menu has 6 recipes. A recipe consists of several sequences (speed/time);
here is an example of a recipe:
Selecting a pre-recorded menu
The menus are selected using the following key combinations:
"Universal menu" press the following keys in quick succession "2 – 5 – 1"
"Coffee shop menu" press the following keys in quick succession "2 – 5 – 2"
"Juice bar menu" press the following keys in quick succession "2 – 5 – 3
"Custom menu" press the following keys in quick succession "2 – 5 – 4"
Note: when the appliance is delivered, the "Custom menu" is empty. See the following
section on how to enter parameters.
Page 10
SANTOS: User and maintenance manual
98162 EN 1.5 - 02 2014 10 / 23 www.santos.fr
Custom menu
Your own menu can be created by assigning one of the 30 pre-recorded recipes to one of
the 6 keys on the control panel.
How to assign a recipe to one of the control panel keys
Note: All 6 keys can be parameterized
For example: to assign recipe n°34 to key n°2
• Type in the following sequence:
"3 – 1 – P"
• Select the key to be programmed
Press key n°2
• Enter the code for the desired recipe (see the table of 30 pre-recorded recipes)
Type code 34 on the keys
• Press key "1" to validate, or one of the other keys to cancel
Once the "custom menu" has been set up, the standard menus can be activated (using the
appropriate code) without deleting the custom menu.
Use the code "2 – 5 – 4" to reactivate the "Custom menu".
CREATING CUSTOM RECIPES
Creating custom recipes
Your own recipes can be created by using a special program available from SANTOS and
Page 11
SANTOS: User and maintenance manual
98162 EN 1.5 - 02 2014 11 / 23 www.santos.fr
a simple USB key for transfer from computer to the appliance.
Note: No special casing is required.
CLEANING:
IMPORTANT:
• In all cases, stop the appliance and unplug the power cable (10).
• The appliance must not be cleaned with a jet of water nor a high pressure
spray
• The motor unit (3) must not be immersed in water.
• Do not use an abrasive sponge to clean the jar (1), protection hood (7) and lid (8)
nor the control panel (5).
• Do not hermetically close the jar when the appliance is stored away (remove the
lid (2)).
• Take care when handling the blade; risk of cuts
• Do not tap the jar against any surface to unstick ingredients: use a flexible
spatula instead
You are advised to clean the appliance as soon as you have finished using it.
It will be easier to clean if you do not allow the remaining scraps of food to dry.
The motor surround (6) can be cleaned using a soft, wet sponge.
Cleaning the jar:
Note: Although the jar and lid can be washed in a dishwasher, it is recommended not to
do so in order to make them last longer.
1. Empty the contents out of the jar and rinse with running water to remove as must
solid residue as possible.
2. Fill the jar with 600 ml warm water (40 to 45°C), add 2 drops of household washing
up liquid, place the lid on the jar to close it and run the cleaning cycle, code "1 – 4 –
2" (30 seconds)
3. Rinse thoroughly with clean water.
Sanitizing the jar:
Use the following procedure in order to be sure it is perfectly sanitized.
1. Clean the jar and lid (see preceding chapter)
2. Fill the jar with 1 liter of sanitizing solution (8ml of sodium hypochlorite solution
containing 2.6% active chlorine, and top up to 1 liter with cold water (20 to
30°Celcius))
3. Close the jar using its lid and run the cleaning cycle, code "1 – 4 – 2" (30
seconds)
4. Once the cycle has ended leave the solution to work for 2 minutes.
5. Rinse thoroughly with clean water.
!
Page 12
SANTOS: User and maintenance manual
98162 EN 1.5 - 02 2014 12 / 23 www.santos.fr
19
20
HOOD SAFETY FEATURE
Note: the appliance will not start unless the hood lid (8) is
closed.
Modifying the safety mode connected with the hood lid
"Pause" mode (by default)
While a cycle is running, opening the hood makes the
motor stop but does not clear the key that is active. When
the hood is closed again, the cycle resumes.
Note: the current cycle will be de-activated if the soundproofing hood remains open for more than 30 seconds.
"Quick stop" mode
Opening the hood makes the motor stop and de-activates the key that was selected.
This code: "4 – P – 1" provides the means for switching from one mode to the other
MAINTENANCE
Prior to carrying out any intervention on the appliance, it must be disconnected from the
mains without fail.
Spare parts:
This appliance requires no specific maintenance. The bearings are lubricated for life.
If any intervention is necessary to replace parts subject to wear, such as the bearing,
blade, electrical or other components, please refer to the parts list (see the exploded view
at the end of this manual).
Whenever ordering spare parts (see references in the exploded view at the end of this
manual), please quote the following:
the type
the appliance serial number and
the electrical specifications (16)
given under the appliance.
Changing the drive system:
Motor drive (female):
Hold the motor drive (20) in position with multiple slip
joint pliers, and unscrew the fixing screw (19) using a
TORX wrench (anticlockwise)
!
Page 13
SANTOS: User and maintenance manual
98162 EN 1.5 - 02 2014 13 / 23 www.santos.fr
17
24
Blade drive (male):
The blade drive is an integral part of the jar ball
bearing assembly (12). The whole assembly must
be replaced (drive – main bearing – ball bearing)
• Turn the jar upside down.
• Using a large flat screwdriver, loosen the
bearing fixing ring (17) (anticlockwise)
• Remove the bearing fitted with the blender
blade from the jar
(see next section for how to dismantle the blade)
Changing the blade:
Dismantle the complete bearing assembly (see
previous section)
Dismantling the blade
Hold the blade coupling (24) in position with multiple
slip joint pliers, and unscrew the fixing nut (13)
using a size 12 hexagon wrench (anticlockwise)
Fitting the blade
Take care to comply with the order given for assembly of the various components:
1. lipped seal (15) (be sure to install correctly with lip downwards),
2. thrust washer (14),
3. blade (11) (recesses
upwards),
4. thrust washer (14) (the
lipped seal must be
pushed far enough for
the square of this washer
to work with the square
of the shaft)
5. fixing nut (13) (tighten
the nut by hand,
checking that the washer
in point 4 is correctly
positioned relative to the
square of the shaft.
Tighten the fixing nut.
11
13
14
12
16
14
15
18
17
Page 14
SANTOS: User and maintenance manual
98162 EN 1.5 - 02 2014 14 / 23 www.santos.fr
Assembling the bearing on the jar
• Place the bearing seal (16) on the bearing (12)
• Place the locking ring seal (18) on the locking ring (17)
• Place the bearing (12) inside the jar (1)
• Screw down the locking ring, take care that the locking ring seal remains in its
seating
• Tighten well by hand, or with a lever
Page 15
SANTOS: User and maintenance manual
98162 EN 1.5 - 02 2014 15 / 23 www.santos.fr
FAULT FINDING
Identifying the cause of appliance stoppage with precision.
In all circumstances, if the problem persists, disconnect the electric power supply (unplug
the mains power cord (10)) and call on someone from the maintenance department or
contact an approved SANTOS dealer.
The appliance will not start:
The LCD screen does not light up:
• Check : the mains supply, the condition of the power cord (10).
• Check that the On/Off switch (4) is at position 1
• Check that the ammeter protection system has not been triggered due to an
overload. (see the paragraph: "The appliance stops following a motor overload")
• Switch the appliance off then on again
• After powering up the 6 key diodes should light up quickly and the screen display
"READY". If not, check on the condition of the wiring and connections in the switch
(4), the component support module and the control panel. (this operation must be
carried out by a qualified person)
The LCD screen shows "NOT READY":
• This message indicates that one of the keys was already
activated before powering up.
• Remove any item liable to activate the keys, clean the control
panel.
The LCD screen shows "LID OPEN":
• Close the safety hood lid (8)
The LCD screen shows "READY":
• Switch the appliance off then on again
• After powering up the 6 key diodes should light up quickly and
the screen display "READY".
• If not, check the connections on the cable connecting the
control panel to the electronic module (this operation must be carried out by a
qualified person).
Page 16
SANTOS: User and maintenance manual
98162 EN 1.5 - 02 2014 16 / 23 www.santos.fr
The blade does not rotate
• Check that there are no foreign bodies stuck in the jar.
• Check the condition of the drive system (motor and blade)
The appliance stops after the motor has overheated, "OVER TEMP": (the motor
unit is hot)
• Put the On / Off switch (4) to the 0 position and unplug the appliance.
• Wait for the motor to cool down (20 to 45 minutes) then press the On / Off switch (4)
(position 1).
The appliance stops as a result of an overload
The LCD screen does not light up
A motor overload can occur if there is an excessive quantity or something too hard in the
jar.
Under these circumstances, either the thermal protection or the excess current protection
may be activated and stop the appliance operating.
If the appliance is hot, refer to the section "The appliance stops as a result of motor overheating").
Otherwise:
• Turn off the electric power supply (unplug the mains power cord (10))
• Move the On / Off switch (4) to the 0 position.
• Under the appliance (fig. O), press the button (25) to reset the excess current
protection. If the button does not remain in the "reset" position, allow the appliance to
cool down before repeating the operation.
The appliance stops further to an overload "OVERLOAD":
A motor overload can occur if there is an excessive quantity or
something too hard in the jar.
• The recipe is not appropriate for the quantity and consistency.
• Reduce the quantity.
• Chose a different recipe with slower speeds.
The appliance resets while it is operating:
Eliminate all multiple power sockets and plug the appliance into its own individual power
supply.
Noises, vibrations, leaks at jar blade level
• Check the blade is correctly tightened (first dismantle the blade bearing)
• Replace the bearing seals
See the chapter: "Changing the blade"
If the problem persists, turn the appliance electric power off (unplug the mains power cord
(4)) and call on someone from the maintenance department or contact an approved
SANTOS dealer.
Page 17
SANTOS: User and maintenance manual
98162 EN 1.5 - 02 2014 17 / 23 www.santos.fr
Problem with the recipes
A few basic rules make it easier to understand how a blender works and thus know how
to adapt the recipe cycles to the products being processed.
Note: Do not overload the appliance: it is better to run a short recipe twice rather than
double the quantities and cycle time: prolonged operation heats the food due to friction
and affects the desired texture with the recipe.
The final mixture is too hot. Once an evenly mixed texture has been obtained, carrying
on blending will make the food heat up: reduce the speed or recipe time.
The final mixture is not even in texture:
• the recipe is not appropriate for the quantity and products processed; reduce the
quantity of food in the jar, increase the cycle time, use smaller pieces of food
(having evenly sized pieces of food makes it easier to carry out the recipe).
• Liquid is needed to make the solid food reach the blade. Increase the amount of
liquid, pour in the liquid before adding the solid foods.
Ice cubes remain stuck to the jar walls:
• Reduce the quantity of ice cubes when they are processed without any liquid
• It is better to add liquid with the ice cubes, always putting the liquid in first.
The mixture "bounces" fast up and down the jar:
• Reduce the speed to adapt it to the quantity being processed so that the blade is
constantly immersed in the mixture. The recipe will take place more quickly and
the mixture will be more even.
High speeds are not suitable for recipes with small quantities
• Increase the amount of product being processed.
Page 18
SANTOS: User and maintenance manual
98162 EN 1.5 - 02 2014 18 / 23 www.santos.fr
APPLIANCE TECHNICAL SPECIFICATIONS
TECHNICAL SPECIFICATIONS
Model 62
Single phase
Supply voltage
(V)
220-240 100-120
Frequency
(Hz)
50/60 50/60
Motor: Nominal
Input power
(W)
1000
Max. current
(A)
8
Speed:
(rpm)
2500 to 15000
Glass touch screen
Yes
Cup capacity
(L)
1.4
Pre-recorded recipes
30
Additional recipes parameterizable
6
Partial counter Yes
Safety/sound-proofing hood
Yes
USB Host port Yes
Motor overload safety feature:
Yes
Motor overheating safety feature:
Yes
Excess voltage safety feature
Yes
Intermittent operation
60 seconds on and
60 seconds off
Dimensions: Height
(mm)
441
Width
(mm)
201
Depth
(mm)
247
Weight: Net weight
(kg)
8.3
Weight including packing
(kg)
9.8
Noise: (2) LpA
uncertainty K
pA
= 2.5dB
(dBA)
73
(1) These ratings are given for your guidance. The exact electrical specifications of your appliance
can be found on the rating plate.
(2) Noise level measured in acoustic pressure of appliance loaded as per the following standards:
NF EN 12852 :2010, ISO 11201:1995 and ISO 4871:1996.
Appliance placed on a work surface at 75cm from the floor.
Microphone turned towards the
appliance at 1.6m from the ground and 1m from the appliance.
Page 19
SANTOS: User and maintenance manual
98162 EN 1.5 - 02 2014 19 / 23 www.santos.fr
Wiring diagram 110-120V 50/60Hz and 220-240V 50/60Hz
Ammeter
protection
Black
Black
Motor
White
White
Green / yellow
Black
White
Black
Control panel
LCD
Bundle
Keys
Electronic
card
2
4 5 1
On /Off
Red
Green / yellow
Blue
Brown
N G L
Blanc
Fan
(option)
P9
P2
Black
Th
(option)
Motor
filter
Page 20
SANTOS: User and maintenance manual
98162 EN 1.5 - 02 2014 20 / 23 www.santos.fr
Element cross-reference table
Simplified list of appliance codes
Functions: Codes
"Universal menu" "2 – 5 – 1"
"Coffee shop menu" "2 – 5 – 2"
"Juice bar menu" "2 – 5 – 3"
"Custom menu" "2 – 5 – 4"
Allocation of a recipe to a key "3 – 1 – P"
Partial counter "4 – 5 – 2"
Cleaning cycle: "1 – 4 – 2"
Activation of "Pause" / "Quick stop" mode "4 – P – 1"
MARK
Description
1
Jar 2 Jar lid
3
Motor base
4
Switch
5
Control panel
6
Motor housing
7
Protective hood
8
Hood lid
9
Jar mat
10
Mains plug
11
Blade
12
Blade bearing
13
Blade tightening nut
14
Blade thrust washer
15
Blade shaft seal
16
Bearing seal
17
Bearing tightening ring
18
Locking ring bearing seal
19
Motor drive fixing screw
20
Motor drive
21
Table seal
22
LCD screen
23
Control panel keys
24
Blade drive
25
Current overload protector
Page 21
SANTOS: User and maintenance manual
98162 EN 1.5 - 02 2014 21 / 23 www.santos.fr
Figures
Fig. A
2 9 5 8 7 3 4 6 1
1
2
11 21 22
23 20
3
Page 22
SANTOS: User and maintenance manual
98162 EN 1.5 - 02 2014 22 / 23 www.santos.fr
10
Fig. B
11
13
14
12
16
14
15
18
17
Page 23
SANTOS: User and maintenance manual
98162 EN 1.5 - 02 2014 23 / 23 www.santos.fr
WARRANTY CERTIFICATE
WARRANTY
Since the 01.01.95, all our appliances comply with CE and possess the CE label. Our guarantee is
of 24 months from the manufacturing date mentioned on the descriptive plate, except concerning
the asynchronous motors (consisting of a rotor and a stator) which are warranted for 5 years from
their manufacturing date. Warranty is strictly limited to the free replacement of any part of origin
recognized by us as defective due to a defect or building default and identified as belonging to the
concerned appliance. Warranty does not apply to damages resulting from installation or use noncomplying with our appliance data sheet (user’s manual) or in case of an evident lack of
maintenance or disrespect of elementary security electric rules. It does not apply in case of regular
wear and tear. Any replacement of parts under warranty will be realized after return of the
defective part in our workshops, postage paid, supported by a copy of a conformity statement on
which appears the serial number of the appliance. Every appliance is equipped with a descriptive
plate conforming to the EC recommendations and of which a duplicate exists in the conformity
statement (serial number, manufacturing date, electrical characteristics …). In case of serious
damage judged repairable only in our workshops, and after prior consent from our departments,
any appliance under guarantee is sent by the Distributor, carriage paid. In case of repairs or
reconditioning of appliances not under guarantee, the round trip transport is payable by the
distributor. The parts and workforce are invoiced at the current rate. A preliminary estimate can be
supplied.
Coffee grinder not using SANTOS original burrs are not taken under guarantee. The warranty
conditions, repairs, reconditioning, of the espresso coffee grinder are the object of a specific note.
Our guarantee does not extend to the payment of penalties, the repair of direct or indirect
damages and notably to any loss of income resulting from the nonconformity or the defectiveness
of products, SANTOS's global responsibility being limited to the sale price of the delivered product
and to the possible repair of the defective products.
In case of revelation of an imperfection during the warranty period, the Distributor has to, unless a
different written agreement of SANTOS, indicate to his customer to stop any use of the defective
product. Such a use would release SANTOS of any responsibility.
APPLIANCE IDENTIFICATION PLATE
SPECIMEN
For all documents not supplied with
the appliance.
Printed, Faxed and Downloaded
Loading...