Samsung NX10RW5VA0, X10 XTC 1700, X10 XTC 1300 RETAIL, X10 XTC 1500 II, X10 XTC 1300 II Manual

Notices i

Notices

No part of this publication may be reproduced, stored in a retrieval system, or

transmitted, in any form or by any means, mechanical photocopying, recording or

otherwise, without the prior written permission of the manufacturer.

The information within this manual is subject to change without notice.

The manufacturer shall not be held liable for technical or editorial errors or omissions

contained in herein; nor for incidental or consequential damages resulting from the

furnishing, performance or use of this material.

Microsoft Windows is a registered trademark of the Microsoft Corporation.

Product names mentioned herein are for identification purposes only, and may be

trademarks and/or registered trademarks of their respective companies.

Macrovision Statement

If your computer has a DVD drive and an analog TV Out port, the following

paragraph applies:

This product incorporates copyright protection technology that is protected by method

claims of certain U.S. patents and other intellectual property rights owned by

Macrovision Corporation and other rights owners. Use of this copyright protection

technology must be authorized by Macrovision Corporation, and is intended for home

and other limited viewing uses only unless otherwise authorized by Macrovision

Corporation. Reverse engineering or disassembly is prohibited.

Copyright 2003 All rights are reserved

1.1

ii Users Manual

Important Safety Information

Safety Instructions

Your system is designed and tested to meet the latest standards for safety of

information technology equipment. However, to ensure safe use of this product, it is

important that the safety instructions marked on the product and in the documentation

are followed.

Always follow these instructions to help guard against personal injury and

damage to your system.

i

Setting Up your System

• Read and follow all instructions marked on the product and in the

documentation before you operate your system. Retain all safety and operating

instructions for future use.

• Do not use this product near water or a heat source such as a radiator.

• Set up the system on a stable work surface.

• The product should be operated only with the type of power source indicated on

the rating label.

• Ensure that the electrical outlet you are using to power your equipment is easily

accessible in case of fire or short circuit.

• If your computer has a voltage selector switch, make sure that the switch is in

the proper position for your area.

• Openings in the computer case are provided for ventilation. Do not block or

cover these openings. Make sure you provide adequate space, at least 6 inches

(15 cm), around the system for ventilation when you set up your work area.

Never insert objects of any kind into the computer ventilation openings.

• Ensure that the fan vents on the bottom of the casing are clear at all times. Do

not place the computer on a soft surface, doing so will block the bottom vents.

• If you use an extension cord with this system, make sure that the total ampere

rating on the products plugged into the extension cord does not exceed the

extension cord ampere rating.

Important Safety Information iii

Care During Use

• Do not walk on the power cord or allow anything to rest on it.

• Do not spill anything on the system. The best way to avoid spills is to not eat or

drink near your system.

• Some products have a replaceable CMOS battery on the system board. There is

a danger of explosion if the CMOS battery is replaced incorrectly. Replace the

battery with the same or equivalent type recommended by the manufacturer.

Dispose of batteries according to the manufacturer’s instructions. If the CMOS

battery requires replacement insure that a qualified technician performs the task

• When the computer is turned off, a small amount of electrical current still flows

through the computer. To avoid electrical shock, always unplug all power

cables, remove the battery and modem cables from the wall outlets before

cleaning the system.

• Unplug the system from the wall outlet and refer servicing to qualified

personnel if:

– The power cord or plug is damaged.

– Liquid has been spilled into the system.

– The system does not operate properly when the operating instructions are

followed.

– The system was dropped or the casing is damaged.

– The system performance changes.

Replacement Parts and Accessories

Use only replacement parts and accessories recommended by manufacturer.

To reduce the risk of fire, use only No. 26 AWG or larger telecommunications

line cord.

Writtenby:DarylL. Osden

Do not use this product in areas classified as hazardous. Such areas include

patient care areas of medical and dental facilities, oxygen rich environments,

or industrial areas.

Battery Disposal

Do not put rechargeable batteries or products powered by non-removable

rechargeable batteries in the garbage.

Contact the Samsung Helpline for information on how to dispose of batteries that you

cannot use or recharge any longer.

Follow all local regulations when disposing of old batteries.

iv Users Manual

Laser Safety

All systems equipped with CD or DVD drives comply with the appropriate safety

standards, including IEC 825. The laser devices in these components are classified as

“Class 1 Laser Products” under a US Department of Health and Human Services

(DHHS) Radiation Performance Standard. Should the unit ever need servicing, contact

an authorized service location.

Laser Safety Note:

Use of controls or adjustments or performance of procedures other than those

specified in this manual may result in hazardous radiation exposure. To

prevent exposure to laser beams, do not try to open the enclosure of a CD or

DVD drive.

Power Cord Requirements

The power cord set (wall plug, cable and AC adapter plug) you received with your

computer meets the requirements for use in the country where you purchased your

equipment.

Power cord sets for use in other countries must meet the requirements of the country

where you use the computer. For more information on power cord set requirements,

contact your authorized dealer, reseller, or service provider.

General Requirements

The requirements listed below are applicable to all countries:

• The length of the power cord set must be at least 6.00 feet (1.8m) and a

maximum of 9.75 feet (3.0m).

• All power cord sets must be approved by an acceptable accredited agency

responsible for evaluation in the country where the power cord set will be used.

• The power cord set must have a minimum current capacity of 7 A and a

nominal voltage rating of 125 or 250 volts AC, as required by each country’s

power system.

• The appliance coupler must meet the mechanical configuration of an EN 60

320/IEC 320 Standard Sheet C7 connector, for mating with appliance inlet on

the computer.

Regulatory Compliance Statements v

Regulatory Compliance Statements

Wireless Guidance

Low power, Radio LAN type devices (radio frequency (RF) wireless communication

devices), operating in the 2.4 GHz Band, may be present (embedded) in your notebook

system. The following section is a general overview of considerations while operating

a wireless device.

Additional limitations, cautions, and concerns for specific countries are listed in the

specific country sections (or country group sections). The wireless devices in your

system are only qualified for use in the countries identified by the Radio Approval

Marks on the system rating label. If the country you will be using the wireless device

in, is not listed, please contact your local Radio Approval agency for requirements.

Wireless devices are closely regulated and use may not be allowed.

The power output of the wireless device or devices that may be embedded in your

notebook is well below the RF exposure limits as known at this time. Because the

wireless devices (which may be embedded into your notebook) emit less energy than

is allowed in radio frequency safety standards and recommendations, manufacturer

believes these devices are safe for use. Regardless of the power levels, care should be

taken to minimize human contact during normal operation.

As a general guideline, a separation of 20 cm (8 inches) between the wireless device

and the body, for use of a wireless device near the body (this does not include

extremities) is typical. This device should be used more than 20 cm (8 inches) from the

body when wireless devices are on and transmitting.

This transmitter must not be collocated or operate in conjunction with any other

antenna or transmitter.

Some circumstances require restrictions on wireless devices. Examples of common

restrictions are listed below:

Radio frequency wireless communication can interfere with equipment on

commercial aircraft. Current aviation regulations require wireless devices to be

turned off while traveling in an airplane. 802.11B (also known as wireless

Ethernet or Wifi) and Bluetooth communication devices are examples of

devices that provide wireless communication.

vi Users Manual

In environments where the risk of interference to other devices or services is

harmful or perceived as harmful, the option to use a wireless device may be

restricted or eliminated. Airports, Hospitals, and Oxygen or flammable gas

laden atmospheres are limited examples where use of wireless devices may

be restricted or eliminated. When in environments where you are uncertain of

the sanction to use wireless devices, ask the applicable authority for

authorization prior to use or turning on the wireless device.

Every country has different restrictions on the use of wireless devices. Since

your system is equipped with a wireless device, when traveling between

countries with your system, check with the local Radio Approval authorities

prior to any move or trip for any restrictions on the use of a wireless device in

the destination country.

If your system came equipped with an internal embedded wireless device, do

not operate the wireless device unless all covers and shields are in place and

the system is fully assembled.

Wireless devices are not user serviceable. Do not modify them in any way.

Modification to a wireless device will void the authorization to use it. Please

contact manufacturer for service.

Only use drivers approved for the country in which the device will be used. See

the manufacturer System Restoration Kit, or contact manufacturer Technical

Support for additional information.

Regulatory Compliance Statements vii

United States of America

Unintentional Emitter per FCC Part 15

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:(1) this device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesired operation.

Writtenby:DarylL. Osden

This equipment has been tested and found to comply with the limits for a Class

B digital device pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generate uses and can radiate radio

frequency energy and if not installed and used in accordance with the

instructions may cause harmful interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

If necessary, the user should consult the dealer or an experienced radio/television

technician for additional suggestions. The user may find the following booklet helpful:

“Something About Interference.” This is available at FCC local regional offices. Our

company is not responsible for any radio or television interference caused by

unauthorized modifications of this equipment or the substitution or attachment of

connecting cables and equipment other than those specified by our company. The

correction will be the responsibility of the user. Use only shielded data cables with this

system.

Intentional emitter per FCC Part 15

Low power, Radio LAN type devices (radio frequency (RF) wireless communication

devices), operating in the 2.4 GHz Band, may be present (embedded) in your notebook

system. This section is only applicable if these devices are present. Refer to the system

label to verify the presence of wireless devices.

Wireless devices that may be in your system are only qualified for use in the United

States of America if an FCC ID number is on the system label.

viii Users Manual

The FCC has set a general guideline of 20 cm (8 inches) separation between the device

and the body, for use of a wireless device near the body (this does not include

extremities). This device should be used more than 20 cm (8 inches) from the body

when wireless devices are on. The power output of the wireless device (or devices),

which may be embedded in your notebook, is well below the RF exposure limits as set

by the FCC.

This transmitter must not be collocated or operate in conjunction with any other

antenna or transmitter.

Operation of this device is subject to the following two conditions: (1) This device may

not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation of the device.

Wireless devices are not user serviceable. Do not modify them in any way.

Modification to a wireless device will void the authorization to use it. Contact

manufacturer for service.

FCC Statement for Wireless LAN use:

“While installing and operating this transmitter and antenna combination the

radio frequency exposure limit of 1mW/cm2 may be exceeded at distances

close to the antenna installed. Therefore, the user must maintain a minimum

distance of 20cm from the antenna at all times. This device can not be

colocated with another transmitter and transmitting antenna.”

FCC Part 68

This equipment compiles with part of the FCC rules. On the back of this equipment is

a label that contains, among other information, the FCC registration number and ringer

equivalence number (REN) for this equipment. If requested, this information must be

provided to the telephone company.

This equipment uses the following USOC jacks : RJ11C

An FCC compliant telephone cord and modular plug is provided with this equipment.

This equipment is designed to be connected to the telephone network or promises

wiring using a compatible modular jack which is Part 68 compliant. See Installation

Instructions for details.

The REN is used to determine the quantity of devices which may be connected to

telephone line. Excessive RENs on the telephone line may result in the devices not

ringing in response to an incoming call. In most, but not all areas, the sum of RENs

should not exceed five (5.0). To be certain of the number of devices that may be

connected to a line, as determined by total RENs, contact the local telephone company

to determine the maximum REN for the calling area.

Regulatory Compliance Statements ix

If the terminal equipment causes harm to the telephone network, the Telephone

Company will notify you in advance that temporary discontinuance of service may be

required. But if advance notice is not practical, the telephone company will notify the

customer as soon as possible. Also, you will be advised of your right to file a complaint

with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations, or

procedures that could affect the operation of the equipment. If this happens, the

telephone company will provide advanced notice in order for you to make necessary

modifications to maintain uninterrupted service.

If trouble is experienced with this equipment (Modem) for repair or warranty

information, please contact your local distributor. If the equipment is causing harm to

the telephone network, the telephone company may request that you disconnect the

equipment until the problem is resolved.

The user must use the accessories and cables supplied by the manufacturer to get

optimum performance from the product.

No repairs may be done by the customer.

This equipment cannot be used on public coin phone service provided by the telephone

company. Connection to party line service is subject to state tariffs.

The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to

use a computer or other electronic device, including fax machines, to send any message

unless such message clearly contains in a margin at the top or bottom of each

transmitted page or on the first page of the transmission, the date and time it is sent and

an identification of the business or other entity, or other individual sending the message

and the telephone number of the sending machine or such business, other entity, or

individual. (The telephone number provided may not be any number for which charges

exceed local or long-distance transmission charges.)

In order to program this information into your fax machine, refer to your

communications software user manual.

x Users Manual

Canada

Unintentional Emitter per ICES-003

This digital apparatus does not exceed the Class B limits for radio noise emissions from

digital apparatus as set out in the radio interference regulations of Industry Canada.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les

limitesapplicables aux appareils numériques de Classe B prescrites dans le règlement

sur le brouillage radioélectrique édicté par Industrie Canada.

Intentional Emitter per RSS 210

Low power, Radio LAN type devices (radio frequency (RF) wireless communication

devices), operating in the 2.4 GHz Band, may be present (embedded) in your notebook

system. This section is only applicable if these devices are present. Refer to the system

label to verify the presence of wireless devices.

Wireless devices that may be in your system are only qualified for use in Canada if an

Industry Canada ID number is on the system label.

As a general guideline, a separation of 20 cm (8 inches) between the wireless device

and the body, for use of a wireless device near the body (this does not include

extremities) is typical. This device should be used more than 20 cm (8 inches) from the

body when wireless devices are on.

The power output of the wireless device (or devices), which may be embedded in your

notebook, is well below the RF exposure limits as set by Industry Canada.

This transmitter must not be collocated or operate in conjunction with any other

antenna or transmitter.

Operation of this device is subject to the following two conditions: (1) This device may

not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation of the device.

To prevent radio interference to licensed service, this device is intended to be

operated indoors and away from windows to provide maximum shielding.

Equipment (or its transmit antenna) that is installed outdoors is subject to

licensing.

Wireless devices are not user serviceable. Do not modify them in any way.

Modification to a wireless device will void the authorization to use it. Contact

manufacturer for service.

Regulatory Compliance Statements xi

Telecommunications per DOC notice

(for products fitted with an IC-compliant modem)

The Industry Canada label identifies certified equipment. This certification means that

the equipment meets certain telecommunications network protective, operation, and

safety requirements. The Department does not guarantee the equipment will operate to

the users’ satisfaction.

Before installing this equipment, users should make sure that it is permissible to be

connected to the facilities of the local telecommunications company. The equipment

must also be installed using an acceptable method of connection. In some cases, the

inside wiring associated with a single-line individual service may be extended by

means of a certified connector assembly. The customer should be aware that

compliance with the above conditions may not prevent degradation of service in some

situations.

Repairs to certified equipment should be made by an authorized Canadian maintenance

facility designated by the supplier. Any repairs or alterations made by the user to this

equipment, or equipment malfunctions, may give the telecommunications company

cause to request the user to disconnect the equipment.

Users should make sure, for their own protection, that the electrical ground connections

of the power utility, telephone lines, and internal metallic water pipe system, if present,

are connected together. This precaution may be particularly important in rural areas.

To avoid electrical shock or equipment malfunction do not attempt to make

electrical ground connections by yourself. Contact the appropriate inspection

authority or an electrician, as appropriate.

The Ringer Equivalence Number (REN) assigned to each terminal device provides

an indication of the maximum number of terminals allowed to be connected to a

telephone interface. The termination on an interface may consist of any combination of

devices subject only to the requirement that the sum of the Ringer Equivalence

Numbers of all the devices does not exceed 5.

xii Users Manual

European Union

The following information is only applicable to systems labeled with the CE mark .

European Directives

This Information Technology Equipment has been tested and found to comply with the

following European directives:

• EMC Directive 89/336/EEC with amending directives 92/31/EEC & 93/68/

EEC as per

– EN 55022 Class B

– EN 61000-3-2

– EN 61000-3-3

– EN 55024

• Low Voltage Directive (Safety) 73/23/EEC as per EN 60950(A1/A2/A3/A4/

A11)

• Radio and Telecom Terminal Equipment Directive 199/5/EC as per

– CTR21 (if fitted with a modem device)

– ETS 300 328 (if fitted with a 2.4 GHz band embedded wireless device)

– ETS 301 489-1 (if fitted with a 2.4 GHz band embedded wireless device)

– ETS 301 489-17 (if fitted with a 2.4 GHz band embedded wireless device)

European Radio Approval Information

(for products fitted with EU-approved radio devices)

This Product is a Notebook computer; low power, Radio LAN type devices (radio

frequency (RF) wireless communication devices), operating in the 2.4 GHz band, may

be present (embedded) in your notebook system which is intended for home or office

use. This section is only applicable if these devices are present. Refer to the system

label to verify the presence of wireless devices.

Wireless devices that may be in your system are only qualified for use in the European

Union or associated areas if a CE mark with a Notified Body Registration Number

and the Alert Symbol is on the system label.

The power output of the wireless device or devices that may be embedded in you

notebook is well below the RF exposure limits as set by the European Commission

through the R&TTE directive.

Regulatory Compliance Statements xiii

European States qualified under wireless approvals:

EU

Austria, Belgium, Denmark, Finland, France (with frequency

restrictions),

Germany, Greece, Ireland, Italy, Luxembourg, The

Netherlands, Portugal, Spain, Sweden and the United Kingdom.

Accept EU

Iceland, Liechtenstein, Norway and Switzerland

European States with restrictions on use:

EU

In France, the frequency range is restricted to 2446.5-2483.5 MHz for

devices above 10 mW transmitting power such as wireless LAN.

Accept EU No limitations at this time.

European Telecommunication Information

(for products fitted with EU-approved modems)

Marking by the symbol indicates compliance of this equipment to the Radio and

Telecom Terminal Equipment Directive 1999/5/EC. Such marking is indicative that

this equipment meets or exceeds the following technical standards:

CTR 21 – Attachment requirements for pan-European approval for connection to the

analogue Public Switched Telephone Networks (PSTNs) of TE (excluding TE

supporting voice telephony services) in which network addressing, if provided, is by

means of Dual Tone Multi-Frequency (DTMF) signaling.

Although this equipment can use either loop disconnect (pulse) or DTMF

(tone) signaling, only the performance of the DTMF signaling is subject to

regulatory requirements for correct operation. It is therefore strongly

recommended that the equipment is set to use DTMF signaling for access to

public or private emergency services. DTMF signaling also provides faster call

setup.

This equipment has been approved to Council Decision 98/482/EEC—“CTR 21” for

Pan-European single terminal connection to the Public Switched Telephone Network

(PSTN).

However, due to differences between the individual PSTNs provided in different

countries, the approval does not, of itself, give an unconditional assurance of

successful operation on every PSTN termination point. In the event of problems, you

should contact manufacturer Technical Support.

xiv Users Manual

Japan

VCCI Statement

This equipment is in the Class B category (Information Technology Equipment to be

used in a residential area or an adjacent area thereto) and conforms to the standards set

by the Voluntary Control Council for Interference by Information Technology

Equipment aimed at preventing radio interference in such residential areas. When used

near a radio or TV receiver, it may become the cause of radio interference. Read

instructions for correct handling.

Wireless Devices

Low power, Radio LAN type devices (radio frequency (RF) wireless communication

devices), operating in the 2.4 GHz Band, may be present (embedded) in your notebook

system. This section is only applicable if these devices are present. Refer to the system

label to verify the presence of wireless devices.

Wireless devices that may be in your system are only qualified for use in Japan if a

TELEC ID is on the system label.

Operational guidelines for 2.4 GHz band wireless equipment (if equipped)

This equipment uses the 2.4 GHz ISM frequency band. The ISM band is the industrial,

scientific, and medical device band. Devices that might also use this band are

microwave ovens, other LAN devices, amateur radio stations, licensed premises radio

stations, and non-licensed specified low-power radio stations.

Regulatory Compliance Statements xv

Prior to setting up your device:

1. Make sure that there are no other devices in your area using the same frequency

band.

2. Change the channel, location, or discontinue device use if you are interfering with

any other radio station.

3. Contact manufacturer if you have any problems with this device.

Using Your Documentation 1

Using Your Documentation

Congratulations on your purchase of a notebook computer with the Windows® XP

operating system. Whether you are new to using a portable computer or are an

experienced user, this user’s manual can help you get the most from your computer.

Manual Documentation Conventions

Information Icons

Three icons and their associated messages appear in this manual. The information

icons are placed before the step/information they apply to:

Warning:

Indicates the possibility of personal injury.

Caution:

Warns you of possible damage to equipment or data.

Note:

Informs you of special circumstances.

Technical Information:

Informs you of special requirements or limitations for use of item(s).

Keyboard Conventions

Keys that you need to press to perform certain functions are displayed in the manual in

brackets. For example:

<Ctrl> indicates the control key (Ctrl on the keyboard).

If you need to press two keys at the same time, the key names are shown joined by a

plus sign. For example:

<Fn+F8> means that you should press the Fn key and hold it and then press the F8

key.

2 Users Manual

CD-ROM Device Naming Convention

In many installation programs you will have to get a program from the CD-ROM

device. The program installation sequence assumes that the CD is drive d:\, however

this is not always the case. The name of the CD-ROM drive is the letter following the

letter assigned to your last HDD. For instance, if you have one HDD with two

partitions, the HDD is drives C: and D: and the CD-ROM drive is then drive E.

Touchpad Conventions

You may be asked to click or double-click on items on the display screen. As a general

note the touchpad actions act much in the same way as a wheel mouse, any differences

are explained fully.

The object that needs to be clicked upon will be displayed in Bold text or shown in a

small figure such as the “Start Button” shown on the right =>.

Table 1. Touchpad Click Conventions

Windows Conventions:

Almost all “Windows” programs will display the name/function of a button or

icon if you place the touchpad pointer on the item you want information about.

Software User Documentation

Your computer is shipped from the factory with several software programs installed.

The software may include its own online or printed documentation. Refer to the

documentation or the Help options in the software for more information.

The figures and illustrations in this manual may not be identical to those on

your system.

General Icon Note:

Some of the Icons used in Windows XP may be placed on the taskbar by

selecting (ex: Place the volume icon in the taskbar) in the properties dialog

box.

Action Process

Click Depress the touchpad left button and release

Double-click Quickly click the left touchpad button two times

Introducing Your Computer 3

Introducing Your Computer

Your computer is a lightweight portable computer that includes following features to

meet your computing needs at home or on the road:

- Home Theater System Support (dependant on configuration)

- CD-RW/DVD-ROM Combo Drive

Factory options (Figures may be different depending on options)

- Fingerprint recognition system - Memory Stick

- Wireless LAN (802.11b) - Bluetooth

Where Everything Is

The next section will explain the location of all of the buttons, LEDs and equipment

needed to operate your notebook computer.

Front

SENS Keyboard Buttons

LEDs

Power Button

Touchpad

Touchpad Buttons

Scroll Wheel/

Fingerprint Sensor

Speaker

LCD Cover Latch

Keyboard

Memory Stick Slot (option)

* Either fingerprint sensor

or scroll wheel is installed

depending on factory

configuration.

LEDs

Speaker

4 Users Manual

Right Side

Left Side

Back Side

Earphone Jack

Microphone Jack

CD-RW/DVD-ROM

Combo Drive

USB Port

Fan Vent

Modem Port LAN Port

VGA Port

USB Port PCMCIA Slot

1394 Port

TV-Out

Port

(S-VHS)

S/PDIF Jack

DC Jack

Battery

Security Lock Port

Introducing Your Computer 5

Bottom

Battery Latches

Memory

Compartment

HDD

Compartment

Mini-PCI

Compartment*

* Wireless communication module(option) is installed in the mini PCI compartment.

6 Users Manual

Using Your Computer for the First Time

This section gives you detailed information on using your computer for the first time.

Turning On the Computer

To turn on the computer’s power for the first time:

1. Install the battery and connect the AC adapter according to the Installation Guide.

2. Slide the LCD cover latch to the right.

3. Lift up the cover.

4. Press and then release the power button.

The power LED is on when the computer’s power is on.

Initial Computer Startup:

The first time you start your computer you will see the operating system

registration screens. Simply read each screen and follow the simple directions.

You must complete this process in order to use your computer. A tutorial is

provided if you require it.

Power

Button

Power LED

LCD Cover Latch

Using Your Computer for the First Time 7

Turning Off Your Computer

Prior to shutting down your computer ensure all of your data and current work are

saved. The system will ask if you wish to save any unsaved work, saving your work

first will speed the shutdown process.

To turn off the computer, complete the following steps:

1. Click on the taskbar.

If you need to restart your computer after software (re)installation or because it is

not responding select the Restart option in step 3 below.

2. Click Shut Down Computer to display the shutdown popup window shown

below.

3. Click Turn Off to complete the shutdown sequence.

Power Off:

If the system does not power off, then press and hold the power button for over

4 seconds. See ”Using Power Management Options” on page 66.

Power Button Functions:

The power button has several functions other than just turning on and off your

computer, see “Using Power Management Options” on page 66.

You can also perform a soft boot by saving your files and pressing

<Ctrl+Alt+Del> to pop-up the “Windows Task Manager” window.

Click Shut Down > Restart.

You can perform a cold boot by pressing the power button for more than 4 seconds to

turn the computer off, waiting more than five seconds, and then pressing the power

button to turn the computer on. The system may perform some extra checks during the

restart.

8 Users Manual

Tips for Using Your Computer

The following information helps you avoid potential problems as you use your

computer:

Do not try to disassemble your computer. Opening the system chassis voids

your warranty. Only an authorised manufacturer service center can replace or

add any parts inside the chassis.

• Follow all the instructions and cautions in your computer user documentation.

• The LCD has a polarized surface and can be damaged easily. To prevent

damage, avoid touching the screen.

• Use only approved AC adapters, auto adapters, memory modules and other

options.

• Because a notebook computer is small and has restricted air flow around

components, it is more likely to overheat than a desktop computer. A fan inside

your computer runs when needed to help eliminate heat. Make sure the fan vent

on the left side of your computer is not blocked when you use the computer.

Occasionally check the vents and remove any accumulated dust on the outside.

• Avoid using or storing the computer in extremely hot or cold areas, such as a

car on a hot day. Keep the computer away from heaters and out of direct

sunlight. Exposure to excessive heat may damage computer components. If you

have left your computer in a hot place, let it cool down slowly to room

temperature (with the LCD panel open) before using it.

• Do not remove the memory-module compartment door, or try to install a

memory module when the computer is on. (For information on installing

memory modules, see “Installing a Memory Module” on page 80.)

• Set up your computer work area to avoid physical strain. Sit with your back

straight and supported by your chair. Adjust your chair or work table so that

your arms and wrists can remain in a relaxed position, parallel with the floor.

Avoid bending or twisting your wrists as you work. Your hands should “float”

slightly above the keyboard. Refer to a book on office ergonomics for more

information on setting up your work area.

• Take frequent breaks from working at the computer to rest your eyes and

stretch your muscles.

• Remember to save your data files frequently and to make backup copies of your

files.

Using Your Computer for the First Time 9

Travelling with Your Computer

Air Travel

If you are travelling by air, follow these tips:

• Take the computer with you as carry-on luggage. Do not check the computer

with your baggage.

• Allow the computer and disks to go through the X-ray security devices. Do not

hand-carry disks through the walk-through metal detectors, which can cause

loss of data.

• Make sure that the battery is charged or the power cord is easily accessible.

You may be required to turn on the computer for airport security personnel.

• Be prepared to turn off the computer during take off and landing.

Locking your Computer

As a precaution when you are travelling or using your computer in an unsecured area,

you should keep your computer as safe as possible. An option to do this is the Security

Lock System. Follow the Security Lock System manufacturers instructions for specific

installation and use. The following figure shows generally how to use the lock.

10 Users Manual

Handling Spills

Do not spill anything on your computer. The best way to avoid spills is to avoid eating

and drinking around your computer. If you do spill something on your computer, turn

off your computer, unplug it immediately, and do the following:

• If you spill liquid on the keyboard, drain as much of the liquid from the

keyboard as possible. Be careful not to let the liquid drip onto the LCD panel.

Allow the system to dry for several days before trying to use it.

• If you spill liquid on an external keyboard or keypad, unplug it and drain as

much of the liquid as possible. Allow the keyboard to sit at room temperature

for a full day before trying to use it.

Sweet liquids leave a sticky residue that may jam the keyboard despite your

efforts to dry it.

• If you spill liquid on the LCD panel, clean it immediately with a soft cloth and

denatured alcohol or a proprietary LCD screen cleaner. Do not use water,

window cleaner, acetone, aromatic solvent, or dry, rough towels to clean it.

Some liquids damage the polarized LCD screen. If your screen is damaged,

contact your authorized manufacturer’s service center for a replacement.

Storing the Computer for Long Periods

If possible, leave the power cord connected to the computer and an electrical outlet

when the computer is not in use. This extends the life of the battery and keeps the

battery fully charged.

If you will not be using the computer for a long period of time (a month or more), you

should charge the battery until it is completely full. After you have done so, remove the

battery from the unit.

Using the Keyboard 11

Using the Keyboard

Your computer has an 87/88-key keyboard. By pressing designated key combinations,

you can have access to all the key functions of a full-sized keyboard.

Although the layout of the keys on your computer’s keyboard is different from

that on a desktop computer’s keyboard, the keyboard feels like a full-sized

keyboard when you use it.

The keys on the keyboard can be grouped into the following categories:

• Full-sized Alphanumeric typewriter keys are arranged like a standard

typewriter keyboard and are used for text entry. The Windows keys on either

side of the spacebar open Windows menus and perform other special functions.

• Function keys, when pressed together with the <Fn> key, enable special

functions.

• Cursor and Screen control keys move the cursor. They may perform other

functions, depending on your software.

Function & Special Purpose Keys

Embedded Numeric Keypad

Application Key

Cursor/Screen

Control Keys

Windows

Key

Function

Key

12 Users Manual

To clean the computer keyboard, use slightly damp cotton swabs. Scrub the keys and

the surface around the keys.

Do not allow liquid to drip into the keyboard or you may damage the keyboard.

Using the Numeric Keypad

Your keyboard includes a numeric keypad, which is a group of keys that you can set to

type numbers and mathematical symbols, such as the plus sign. A number or symbol

on the right corner of each keypad key shows its numeric function.

Press <Fn+F11> to turn on the embedded numeric keypad. The numeric functions of

the keypad are enabled and the Num Lock LED turns on. (See ”Reading the System

Status Lights” on page 19 for the location of the Num Lock LED.)

While the numeric functions are enabled, you can temporarily return a key to its normal

function by pressing the key and the <Fn> key. For example to type the letter m, press

<Fn+M>, this operation displays the letter m.

To turn the numeric keypad off, press <Fn+F11> again. The Num Lock LED turns off.

Num Lock LED

Using the Keyboard 13

Using Special Function Keys

The function key activates special functions when it is pressed in combination with

another keys. Table 2 shows the special key combinations.

Table 2. Description of Special Function Key Combinations

When you press a function key combination, the system sound may be

temporarily muted.

<Fn> Key

Combinations

Key Name Key Function

<Fn+Esc> Esc

Rest

Rest Puts the computer into Suspend mode. To resume

normal operation from rest, press the power button.

<Fn+F2> F2

Gauge

Gauge Displays the battery gauge and the power source in

the upper-left corner of your screen. The gauge

closes in a few seconds.

<Fn+F4> F4

LCD/CRT

LCD/CRT Switches the display between the LCD, the external

display device, and simultaneous display on both the

LCD and the external display device.

<Fn+F6> F6

Mute

Mute Mutes the audio.

<Fn+F7> F7

S/PDIF

S/PDIF Toggles the S/PDIF function On/Off.

<Fn+F11> F11

Num Lock

Num Lock Activates the numeric keypad.

<Fn+F12> F12

Scroll

Scroll In some applications, sets the cursor-control keys to

scroll the page up or down while the cursor position

does not change. Pressing key combination again

turns off the scrolling function.

<Fn+Up Arrow> Up Arrow Brightness

Up

Increases the LCD brightness.

<Fn+Down Arrow> Down Arrow Brightness

Down

Decreases the LCD brightness.

<Fn+Right Arrow> Right Arrow Volume Up Increases the audio volume.

<Fn+Left Arrow> Left Arrow Volume

Down

Decreases the audio volume.

14 Users Manual

User Defined Buttons (SENS Keyboard)

You may program the four buttons to the left of the power button to start any program

you have installed on your computer.

The default settings for these buttons are:

What is Bluetooth?

Bluetooth is a worldwide standard for the wireless exchange of data between

two devices.

Using Wireless LAN/Bluetooth Button

Loading or unloading wireless LAN/Bluetooth driver takes about 5 seconds.

Therefore, if you turn wireless LAN/Bluetooth on/off using the wireless LAN/

Bluetooth button, the button does not work in 5 seconds. (For wireless LAN/

Bluetooth installed models)

Icon Name Function

Internet Button Launches Internet Explorer.

E-Mail Button Launches Outlook Express.

User Button Executes user-defined action.

WLAN/Bluetooth

On/Off Button

Turns WLAN/bluetooth on and off.

(If you do not have WLAN/Bluetooth module installed, an additional

User Button is provided instead.)

Using the Keyboard 15

To reprogram the Sens Keyboard, follow the steps below:

1. Double-click icon on the Windows taskbar, the Key Setting window is

displayed.

2. Use the Browse button to locate the program you wish to assign to the SENS

Keyboard button selected.

3. Click on your program choice to select it. Click Open.

4. Click OK to close window and complete programming the Sens Keyboard.