Samsung WF520ABP/XAA, WF501ANW/XAA, WF511ABW/XAA, WF457ARGSWR/A2, WF457ARGSWR/AA Installation Guide

WASHING INSTALLATION GUIDE

MACHINE

Parts supplied			Tools needed
	Type1 Type2	Tie strap	Tape measure	carpenter’s	Pilers Flat screwdrilver
Wrench	Bolt hole covers Water supply hoses Hose guide	(option)		level
1 1.PREPARATION.Check the installation location. □ CHECK : Solidly constructed floor (Not Carpeting and soft tile surfaces)
2.And move the washer to the installation location.
* When installing the washer on a pedestal, do the installation before next step.
2 REMOVINGALL SHIPPING BOLTS.

Remove all shipping bolts	Hold the shipping bolt	Fill the holes with the
at the back of washer with	with your hand and pull it	supplied bolt hole covers.
supplied spanner.	through the wide section of
	the hole. Repeat for each
	shipping bolt.

CAUTION: Failure to remove the shipping bolts will cause vibration and noise.

3 COLD & HOT WATER HOSES INSTALLATION ON FAUCETS.					HOT COLD
			Rubber washer
	Coupling	Rubber
		washer
	Make sure a Rubber		Tighten Coupling by hand	Then tighten two-thirds of a	Run water in a bowl or
	washer is inside each		until it is snug.	turn with pliers.	basin to get rid of any debris
	coupling on both ends.				inside hose. Check for HOT
					and Cold water supply.
4	WATER HOSES INSTALLATION ON WASHER.
	COLD (Left)	HOT(Right)
	Water	Water

Connect one end of the	Tighten Coupling by hand	Then tighten two-thirds of a	For proper operation, make
COLD/HOT water supply	until it is snug.	turn with pliers.	sure both Hot & Cold hoses
hoses to the each COLD/			from faucets are connected to
HOT water supply intakes			the corresponding Hot / Cold
at the back of the washer.			water inlets on the washer.

CAUTION: Make sure that the HOT & COLD hoses are switched with each other.

					French on back 
5					Spanish on back 
	CONNECTING THE DRAIN HOSE.
	Drain hose	Case 1. Wash basin	Case 2. Laundry tub Hose	Case 3. Stand pipe
			retainer		Hose
				8” Max	retainer
			96” Max	6” Min
			18” Min		96” Max
				Tie strap	18” Min
	Hose guide		Tie strap
	To keep the drain hose	The drain hose must be	Laundry tub must be no	Do not insert the drain hose
	spout bent, use the	placed at a height between	shorter than 18 in (46 cm)	too far into the stand pipe: 6
	supplied plastic hose	23.6 in (60cm) and 35.4 in	and no longer than 96 in	- 8 inches, and no more.
	guide.	(90cm).	(245 cm).

6 MOVE THE WASHER TO ITS FINAL LOCATIONAND MAKE SURE IT IS LEVELED.

Confirm whether washer is well seated and does not

Your washer must be leveled on all four sides. Use a

shake. Adjust leveling legs, if necessary.

carpenter’s level on all four corners of your washer to

ensure it’s level.

7 LEVEL THE WASHER BYADJUSTING THE FOUR LEVELING LEGS.

Level the washer by turning the leveling	Check whether washer shakes	When your washer is leveled,
wheel in or out as required by using the	and level again, if necessary.	tighten the locking nuts using the
supplied wrench.		wrench or (-) flathead screwdriver.

CAUTION: Your washer must be leveled on all four sides. An unlevel washer may cause vibration.

8	Final Test : Water leakage , Vibration & Noise
	1. Powering your washing machine.
	2. Run a test cycle(Rinse+Spin) with small amount of laundry such as 4~5 Towels.
	(1) Check for any leakage at the hose connections.
	 If water leaks while water is being supplied or drained, check the water connections. (Refer to Step 3,4,5)
	(2) Check for vibration and noise.
	 If the washer rocks and vibrates excessively, level your washer again. (Refer to Step 6,7)
	Visits by a Service Engineer to explain functions, maintenance or installation is
	not covered by warranty.
	INSTALLATION	□No water leakage	□No vibration / noise
	COMPLETION CHECKLIST
		□Water hose connected properly	□Washer leveled
	□Washer plugged in, power OK
		□Drain hose connected properly	□Shipping bolts removed

DC68-02580C-04

Installation Guide-02580C-03_EnCfrMes.indd 1			2012-07-20 3:28:58