Samsung VC-RA52V, VC-RA50V Series, VC-RL52V Series, VC-RL50V Series Operation Manual

Precautions for safety are the contents to
secure the safety of user and to prevent
damage of property etc. Please read carefully
to have proper use of the product.

※ This product has been made to be used in

Korea, and the quality will not be guaranteed in
overseas countries.

(FOR KOREA UNIT STANDARD ONLY)

Robotic vacuum cleaner

Operation manual of the product

VC-RA52V
VC-RA50V* SERIES
VC-RL52V* SERIES
VC-RL50V* SERIES

As the cleaning is conducted by following the lattice
pattern (

) with the ceiling image recognition method,

cleaning can be performed for every part of the room.

Realizing fine and uniform cleaning for every part of the room

Manual cleaning mode

Perform the cleaning
by directly moving the
cleaner with remote
controller.

Reserved cleaning mode

Reserve the cleaning
at desired time when
going out

Partial cleaning mode

Perform the cleaning of
partial area or when
being scattered of small
fragments of cookies etc.

Automatic
cleaning mode

Perform uniform and
convenient cleaning for
every room.

Repeated
cleaning mode

Perform repeated
cleaning until battery is
exhausted.

Various cleaning modes are provided in accordance
with the cleaning circumstances.

Diverse cleaning mode

2

Features and advantages

of product

When remaining amount of battery is not sufficient, the
charger induces the robotic vacuum cleaner, therefore,
accurate automatic charging can be accomplished.

Automatic charging

What is the ceiling image
recognition (Visionary
Mapping TM) method?

As the product moves with its
own judgment on the place
to clean after recognizing the
image of ceiling with the
camera located at the upper
section, every part of the
room can be cleaned.

Features and advantages

of product

3

Approx. 1 cm of threshold can be traveled with special
driving system, therefore, all the rooms can evenly be
cleaned. However, for the sake of safety, the threshold of
more than 1 cm can not be crossed.

Threshold traveling

If lifting the robotic vacuum cleaner while it is in operation,
the motions of driving wheel, power brush, suction motor,
and side rotating brush will be stopped due to the
detection of the sensor.

Safety device

The robotic vacuum cleaner can easily be operated with
the remote controller.

Remote controller

Dust is removed by the rotation of dual side brushes.

Dual side rotating brush

Dust of every corner can be neatly cleaned by approaching to the
corner as much as possible through the minimizing of colliding
impact as the velocity is reduced by 7 obstacle sensors when
encountering with obstacle and through the relieving of the
colliding impact by 2 bumper sensors during the cleaning. (The
obstacle sensor displays higher sensitivity against bright obstacle.)

Soft bumping

Preparation

Installation

Operation

Features and advantages of product .........................

Precautions for safety ........................................................

Items related with the power supply .................................

Before the use ........................................................................

During the use ........................................................................

Handling after the use ..........................................................

Components ...........................................................................

Name of each section .......................................................

Main frame ...............................................................................

Charger .....................................................................................

Remote controller ...................................................................

State indicating screen ..........................................................

Emergency switch ON/OFF ................................................

Installation of the charger .....................................................

Electric charging .....................................................................

Important items for battery ....................................................

Installation of entry prevention tape ....................................

Cleaning start/stop .................................................................

Returning to electric charging ...........................................

Automatic cleaning .................................................................

Partial cleaning ........................................................................

Repeated cleaning .................................................................

Manual cleaning .....................................................................

Reserved cleaning .................................................................

Additional functions ................................................................

Precautions before the handling ........................................

Handling of sensor window and camera ........................

Handling of dust bin and HEPA-filter .................................

Handling of power brush .....................................................

Handling of side rotating brush ..........................................

Handling of driving wheel ....................................................

Confirming items before reporting the failure ..........

Corrective measures for each inspection code .............

Specification of product ....................................................

Disposal guidance of waster electronic product ............

2
5
5
6
9

10

11
12
12

13
14
15

16

17

18
19

20

21

22
23
24
25
26

27
28

29
29
30

31
32
33

34
36

37

39

Contents

4

Handling

Others

Precautions for safety

preparation

5

These are the contents to secure the safety of user and to prevent damage of property.
Please have safe operation by reading carefully of the following items.

Always observe followings for

safety

If caution items are not being observed, wound or
property damage can be occurred to the user.

This product is used 220V as the rated voltage.

If warning items are not being observed, death or serious
wound can be occurred to the user.

Corresponding terminology will be
explained to improve the understanding for
the product operation.

This is the disassembly prohibited
indication.

Refer to the corresponding page.

Contents with which more efficient
use of the product can be realized
will be explained.

Do not impair the power
supply cord by excessively
bending it or pressing it
down with heavy object.

▶ There is the danger of

electric shock or fire.

Items related with the power supply

Do not use the power
source other than 220V or
do not connect several
electric products
simultaneously to one
outlet. (Do not expose the
cord line on the floor.)

▶ There is the danger of electric shock or fire.

If dust, water etc. are
adhered to the pin and
contact section of the power
supply plug, thoroughly
clean them.

▶ There is the danger of

abnormal operation and
electric shock.

Do not use damaged
power supply plug,
power supply cord, or
loosened outlet.

▶ There is the danger of

electric shock or fire.

Do not pull the power
supply cord section or
touch the power supply
plug with wet hand.

▶ There is the danger of

electric shock or fire.

Before the use

Confirm whether dust
bin is assembled before
operating the robotic
vacuum cleaner.

▶ If dust bin is not

assembled, the robotic
vacuum cleaner will not
be operated.

In order to have cleaning of all of the
rooms, open the doors of rooms before
the cleaning.

▶ If the door of room is closed, the robotic

vacuum cleaner can not enter the room.

▶ However, always close the doors of entrance,

veranda, and rest room etc., through which
the robotic vacuum cleaner can be dropped.

Precautions for safety

preparation

6

These are the contents to secure the safety of user and to prevent damage of property.
Please have safe operation by reading carefully of the following items.

Always observe followings for

safety

Never use the robotic vacuum cleaner at the
following locations as it is a household
appliance.

▶ Critical damage (malfunction, breakage) can be

occurred to the product if it is used at the attic,
basement, warehouse, industrial building, separate
space away from indoors, locations where water is
always existed such as bathroom, laundry room etc.,
and narrow and elevated locations such as table,
shelves etc.

▶ At the location where candle or light stand

for desk are placed on the floor.

▶ At the location without people where light is

existed or fireplace is lighted.

▶ At the location where inflammables such as

gasoline, distilled alcohol, thinner, and
ashtray with lighted cigarette etc. are placed.

Never operate the
cleaner at the
location where
inflammable is
placed.

▶ Attach to the zone with the difference of height

of less than 5 cm from the floor.
Example) Entrances of veranda, rest room, low
staircase, and porch etc.

▶ Attach to the fire zone (fireplace, heater, and

candle etc.) or danger zone with moisture.

▶ As entering may be happened in accordance

with the condition of floor surface, close the
doors of rest room, veranda, and porch etc.,
during the cleaning.

Always attach entry
prevention tape to the
zone into which the
robotic vacuum cleaner
can not be entered.

▶ Other place can be contaminated through

the liquid adhered to the wheel.

Be careful not to make
the robotic vacuum
cleaner to be passing
through or sucking in
water, oil, and liquid of
excrement of pet etc.

▶ Fatal damage can be

inflicted on the product.

▶ If dust is accumulated at the falling prevention

sensor window, falling may be happened as
the falling danger zone can not be identified by
the robotic vacuum cleaner.

▶ If falling, injury or damage to the product can

be happened.

Attach entry prevention
tape to railing or
stairway entrance etc.
where falling danger is
existed.

Precautions for safety

preparation

7

In the case of the carpet
with long tassel at the
end, fold the end section
to the inside.

▶ Fatal damage can be

inflicted on carpet and
robotic vacuum cleaner
by being wound to
driving wheel and
power brush.

▶ By all means, remove those products of

breakable ceramic ware or glass, and light
flowerpot etc.

▶ The robotic vacuum cleaner does not identify

coin, ring, or expensive jewelry etc.

Remove in advance
small or breakable
object at the location of
cleaning.

▶ Always remove these

prior to the cleaning.

Never let children
standing or sitting on the
product while it is in
operation.

▶ Through the falling by

mistake, injury can be
inflicted or fatal damage
can be occurred to the
product.

Before the cleaning or
after establishing the
reserved cleaning
function, let all the
persons in the house to
be careful about these
by informing them.

▶ Children can be caught

and fallen by mistake
while they are running.

▶ The robotic vacuum cleaner is supposed

to detect obstacles separated with the
distance of approx. 5 cm.

▶ Thin towel, pad, power supply cord, table

cloth, and belt etc., in front of the
bathroom, sink stand, entrance door, and
multipurpose room etc. can be tangled
with driving wheel or power brush, or can
be the cause of dropping objects on the
table or dinner table.

Put away those
objects scattered on
the floor.

▶ The robotic vacuum cleaner can be the object

of curiosity of child or pet.

▶ Injury can be inflicted if hand, feet, end of

clothes, and hair etc. are caught in the driving
wheel, side rotating brush, and power brush
during the cleaning.

▶ If the robotic vacuum cleaner is interrupted

while being followed along the path, the
particular section may not be cleaned as it is
being recognized as obstacle.

▶ In the case when emergency switch is turned

off, all functions and power supply will be
intercepted.

If child or pet is left
alone, turn off the
emergency switch of
the robotic vacuum
cleaner.

Precautions for safety

preparation

8

These are the contents to secure the safety of user and to prevent damage of property.
Please have safe operation by reading carefully of the following items.

Always observe followings for

safety

Before the use

When installing the charger,
do not expose the power
supply cord on the floor.

▶ During the automatic

electric charging or the
passing in front of the
charger, the robotic
vacuum cleaner can be
moved while drawing the
power supply cord.

Install the charger at the
location where it can be
discovered easily.

▶ If installing it at

recessed area,
automatic electric
charging will be difficult
due to the excessive
unnecessary motions.

If an object is placed in
front of the charger,
automatic electric
charging can not be
performed by the robotic
vacuum cleaner.

▶ Take away the object.

Always insert the power
supply plug of the
charger.

▶ If power is not

supplied, automatic
electric charging can
not be performed.

Remove the obstacles
located in the vicinity
of approx. 1m in front
of and approx. 0.5m
at left and right side
of the charger.

Be careful not to have
the inflow of liquids
such as water, juice
etc. on the charger.

▶ There will be the

danger of electric
shock or fire.

Do not make short the
terminal of charger
with metals such as
chopsticks, driver etc.

▶ Fatal damage can

be inflicted on the
charger.

For the space with the
height less than that of
the robotic vacuum
cleaner (low sofa,
underneath of low bed
etc.), entry may
attempted or jamming
can be occurred,
therefore, attach the
entry prevention tape.

Do not use the charger for another
application.

▶ There will be the danger of fire or

fatal damage to the charger.

Precautions for safety

preparation

9

During the use

The robotic vacuum
cleaner shall not be
used on thick carpet.

▶ This can be the cause

of failure of the robotic
vacuum cleaner.

▶ The carpet may be

damaged by this.

Do not put objects on
the robotic vacuum
cleaner.

▶ Malfunction can be

generated.

Do not use the robotic
vacuum cleaner on
the table or on
elevated place.

▶ If it is fallen, there

will be the danger
of damage.

If sucking in wide paper
or vinyl bag during the
cleaning, remove them
immediately.

▶ If using the appliance

for long time with the
blocked state of the
inlet, fatal damage can
be inflicted on the
product.

If abnormal noise, odor,
or smoke is generated
from the robotic vacuum
cleaner, turn off the
emergency switch
immediately and call the
customer care center.

During the movements
of the robotic vacuum
cleaner, it can be
collided with leg of
chair, leg of desk, table
chair, or thin and long
furniture etc.

▶ For the sake of fast and tidy cleaning,

put the table chair etc. on the table.

During the cleaning of
the robotic vacuum
cleaner, its traveling can
be interrupted by being
caught to the threshold
of entrance door and of
veranda etc.

▶ If the driving wheel of the robotic vacuum

cleaner is not rotated for more than 5 minutes,
all the functions will be suspended and the
movement will be stopped.

▶ In order to have the movement again, after

turning off the emergency switch and moving
the robotic vacuum cleaner to the movable
location by lifting it, turn on the power supply,
and then, perform the cleaning.

Perfect cleaning can not be
realized for the recessed
corner or the space
between sofa and wall etc.
which can not be accessed
by the robotic vacuum
cleaner.

▶ Clean them separately from

time to time.

During the cleaning by the robotic
vacuum cleaner, the phenomenon of
having a lump of dust remained on the
floor may be happened due to the failure
of inhaling it.

▶ Sweep it with another cleaning device.

Handling after the use

During the handling, do
not directly spray water
or polish the outside with
volatile substances such
as benzene, thinner,
and alcohol etc.

▶ Fatal damage can be

inflicted on the product.

Never disassemble or
modify the robotic
vacuum cleaner except
qualified repair
technician.

▶ Fatal damage to the

product can be
happened.

Precautions for safety

preparation

10

These are the contents to secure the safety of user and to prevent damage of property.
Please have safe operation by reading carefully of the following items.

Always observe followings for

safety

Regularly wipe off foreign
material accumulated on
the obstacle sensor and
falling prevention sensor.

▶ The sensors may have

malfunction due to the
covering with foreign
material.

In the case of damaging
power supply cord,
exchange it through the
qualified repair
technician of customer
care center.

▶ There is the danger of

electric shock or fire.

When removing foreign
material, always turn off
the emergency switch in
the first place, and then,
use the brush for
cleaning.

▶ If suddenly activated,

injury or fatal damage
to the product can be
brought.

Do not handle the
charger before
separating the power
supply plug.

When exchanging
battery, call up the
customer care center of
Samsung Electronics.

▶ If using battery which is

not a legitimate
product, it will be the
cause of failure.

Do not squeeze with
force or strongly press
the bumper

▶ If bumper sensor

becomes abnormal,
collision with the
surface of wall or
fixture and so forth
can be happened.

측면

회전솔

측면

회전솔

측면

회전솔

측면

회전솔

측면

회전솔

측면

회전솔

측면

회전솔

측면

회전솔

측면

회전솔

측면

회전솔

측면

회전솔

측면

회전솔

파워브러시

파워브러시

파워브러시

파워브러시

파워브러시

파워브러시

파워브러시

파워브러시

파워브러시

파워브러시

파워브러시

파워브러시

파워브러시

파워브러시

파워브러시

파워브러시

파워브러시

파워브러시

파워브러시

파워브러시

파워브러시

파워브러시

추락방지 센서

추락방지 센서

추락방지 센서

추락방지 센서

추락방지 센서

추락방지 센서

추락방지 센서

추락방지 센서

추락방지 센서

추락방지 센서

추락방지 센서

추락방지 센서

추락방지 센서

추락방지 센서

추락방지 센서

추락방지 센서

추락방지 센서

추락방지 센서

추락방지 센서

추락방지 센서

추락방지 센서

추락방지 센서

추락방지 센서

추락방지 센서

추락방지 센서

추락방지 센서

추락방지 센서

추락방지 센서

추락방지 센서

추락방지 센서

추락방지 센서

추락방지 센서

추락방지 센서

추락방지 센서

장애물 센서

Components

preparation

11

Carefully confirm the

components.

■ Remote

controller

■

Main frame

■

Charger

Brush for cleaning Remote controller stand Spare HEPA filter

(AAA type dry cell)

Operating instruction/dry cell Simple instruction Entry prevention tape (1 set)

■ Main frame

Name of each section

preparation

12

Remember the names of

each section.

Front side

Driving wheel

Battery cover

Power brush

Bottom side

Falling prevention

sensor

Falling prevention

sensor

Side rotating brush

Charging pin

Falling prevention

sensor

Roller

Charging pin

Entry prevention

tape sensor

Power
brush cover

Driving wheel

Emergency switch

Manipulation
button

Obstacle sensor

Obstacle sensor

Bumper sensor

Receiving section of

remote controller

State indicating

window

Remember the names of

each section.

Name of each section

preparation

13

■ Main frame

Side section

Receiving section
of remote
controller

Dust bin

discharging button

Dust bin

■ Charger

Charging terminal

Remote controller
stand

Ventilation port

Catching sill

Charging

lamp

(green)

Power
lamp (red)

■ Remote controller

When purchasing the product, the dry cell is not existed at the remote controller inside.
Assemble the dry cell (AAA type) and use the product.

The method to put in dry cell

Press the cover of rear
side of remote controller
and pull up it to upward

Assemble the dry cell as shown
the picture in the remote
controller. (If the assembly of ⊕
and ⊖ is erroneously performed,
the remote controller will not be
activated.)

After matching the cover
of remote controller to the
groove, close it until the
“click” sound is
generated.

1 2

※ Dimension: Dry cell of AAA size

3

Name of each section

preparation

14

Remember the names of

each section.

VC-RA52V
VC-RL52V* SERIES

VC-RA50V* SERIES
VC-RL50V* SERIES