Samsung SCL Series Specification Sheet
General Features
Applications
Part Numbering
SCL Series
TC SCL 0J 106 M S A R
●
1
●2●
3
●
4
●5●6●7●
8
0
Tantalum Capacitor ( SCL Series )
Abbreviation of Tantalum Capacitor Capacitance Tolerance
Type of Series Case size
Rated Voltage Packing
Capacitance Tolerance Packing Polarity
The SCL series is a slim type of conventional SCS series.
Its ability is same as SCS series even though it has thinner thickness that is
max. 64% of SCS series.
- Environment-Friendly (Pb-free) tantalum capacitor
- Low-profile case size
- Reduced thickness up to 64% of SCS series
- Molded Case available in four case codes.
- Compatible with automatic pick and place equipment.
- Meets or Exceeds EIA standard 535BAAC .
- Terminations: 100 % Sn , RoHS compliant.
- Reduced electronic equipments : mobile phone, PDA, MP3, LCD module etc. - Smoothing
- Circuit of DC-DC Converters & Output side of AC-DC Converters
- De-Coupling Circuit of High Speed ICs & MPUs
- Various Other High Frequency Circuit Applications
SCL Series
0
● ABBRIVIATION OF TANTALUM CAPACITOR
1
● TYPE OF SERIES
2
● RATED VOLTAGE
3
● CAPACITANCE
4
● CAPACITANCE TOLERANCE
5
● CASE SIZE
6
The symbol shows the type of the capacitor.
SCL : Samsung
Capacitor Low-profile series
Symbol DC Rated Voltage Symbol DC Rated Voltage
0E
2.5
1C
16
0G
4
1D
20
0J
6.3
1E
25
1A
10
1V
35
Symbol Capacitance (㎌) Pico Farad (㎊) Symbol Capacitance (㎌) PicoFarad (㎊)
105
1.0 10×10
5
684
0.6 8 68×10
4
106
10.0 10×10
6
475
4.7 47×10
5
Symbol Tolera nce(%) Symbol Tolera nce(%)
K
±
10
M
±
20
Case EIA Code
S
3216-12
T
3528-12
U
6032-15
V
7343-18
SCL Series
0
● PACKING
7
● PACKING POLARITY
8
APPEARANCE AND DIMENSON
Taping and
Reel for Chip
Direction
of Feed
Tape
+ Polar ityMark
R
Tapin g and
Reel for Chip
Direction
of Feed
+ Polar ity Mark
L
Bulk
B
Symbol Packing Code
A
7inch
C
13 inch
Code EIA Code
DIMENSION (mm)
L W
1
W
2
H Z
R
2012-09 2.0 ±0.2 1.25 ±0.2 0.9 ±0.1 0.95max 0.5 ±0.2
S
3216-12 3.2 ±0.2 1.6 ±0.2 1.2 ±0.1 1.2max 0.8 ±0.3
T
3528-12 3.5 ±0.2 2.8 ±0.2 2.2 ±0.1 1.2max 0.8 ±0.3
V
6032-15 6.0 ±0.3 3.2 ±0.3 2.2 ±0.1 1.5max 1.3 ±0.3
W
7343-18 7.3 ±0.3 4.3 ±0.3 2.4 ±0.1 1.8max 1.3 ±0.3
SCL Series
● Standard value and Case size
Ultra Flat Low Profile Tantalum Chip Capacitors
STANDARD VALUE AND CASE SIZE
W.V 4V 6.3V 10V 16V
Ca p.(㎌) (0G) (0J) (1A) (1C)
4.7 475
6.8 685 (S)
10 106 (S) (T)
15 156
22 226 S ,T S (S ),(T) (T)
33 336 S ,T S ,T T
47 476 T T (T)
68 686 (T ) (T)
100 107 (T)
150 157
()Under Development
New products (2005.01~) are show n in blue.
Environmentally friendly tantalum chip capacitors w ith lead-f ree terminal/Conform to RoHS
SCL Series
RELIABILITY TEST CONDITION
NO ITEMS TEST CONDITION PERFORMANCE
1
RATED D C VOLTAGE
-55℃ ~ +85℃
2.5∼35V
2
CAPACITANCE
MEASURING FREQUENCY : 120±12Hz
MEASURING VOLTAGE : 0. 5Vrms + 0.5∼2V DC
MEASURING CIRCUITS : EQUIVALENT SERIES
CIRCUIT
CAPACITANCE RANGE
0.1∼330
㎌
TOLERANCE ON CAP.
±
10%,±20%
3
TANGENT OF L OSS
ANGLE
MEASUREMENT SHALL BE MADE UNDER THE
SAMECONDITIONSASTHOSEGIVENFORTHE
MEASUREMENT OF CAPACITANCE.
4
LEAKAGE CURRENT
THE RATED DC VOLTAGE SHALL BE APPLIED
TO TERMINALS ACROSS THE TEST CAPACITOR
Cx, BY THE METHOD AS SHOWN BELOW. THE
LEAKAGE CURRENT SHALL THEN BE
MEASURED AFTER CHARGE FOR 5 MIN.
MEASURING CIRCUITS
WHERE
RS: STANDARD RESISTOR(PROTECTIVE R :1KΩ)
: DC VOLTMETER OR ELECTRONIC
VOLTMETER
S1 : DC POWER SUPPLY SWITCH
S2 : PROTECTIVE SWITCH FOR A AMMETER
C
X
: TEST CAPACITOR
: DC AM-METER FOR LEAKAGE CURRENT
0.01CV or 0.5
㎂
WHICHEVER IS GREATER
5
IMPEDENCE
AC VOLTAGE(0.5Vrms OR LESS) OF A
FREQUENCY SPECIFIED ON NEXT PAGE SHALL
BE APPLIED AND THE VOLTAGE DROP
ACROSS CAPACITOR TERMINALS SHALL BE
MEASURED
THE IMPEDANCE SHALL BE CALCULATED BY
THE FOLLOWI NG EQUATION.
WHERE
E : VOLTAGE DROP ACROSS THE CAPACITOR
TERMINALS
I : CURRENT FLOWING THROUGH THE
CAPACITOR (FREQUENCY : 100±10kHz)
V
A
+
-
R
S
S
1
S2
V
C
x
A
+
-
Impedance Z
E
I
=
SCL Series
NO ITEMS TEST CONDITION PERFORMANCE
6
TEMPERATURE
STABILITY
THE CAPACITOR SHALL BE SUBJECTED IN TURN TO PROCEDURES SPECIFIED
BELOW
7
SURGE TEST
THE CAPACITOR SHALL BE SUBJECTED TO THE SURGE
VOLTAGE AS SPECIFIED ON NEXT PAGE IN A CYCLE OF 6
±
0.5 MIN. WHICH CONSISTS OF 30±5 SEC. FOLLOWED BY A
DISCHARGE PERIOD OF APPROX. 5 MIN 30 SEC. AT A
TEMPERATURE OF +85℃FOR 1,000 CYCLES.
AND THE CAPACITOR SHALL BE STORED UNDER
STANDARD ATMOSPHERIC CONDITIONS TO OBTAI N
THERMAL EQUILIBRIUM AFTER MEASUREMN\ENT.
MEASURING CIRCUIT
WHERE
R1 : PROTECTIVE SERIES RESISTOR (3 3Ω)
R2 : DISCHARGE RESISTOR( 3 3Ω)
Cx : TEST CAPACITOR
V:DCVOLTAGE
S:SWITCH
STEP TEMP. DURATION
CHANGE IN
CAPACITANCE
(ΔC)
TANGENT OF
LOSS ANGLE
(D.F.)
LEAKAGE
CURRENT
1 25±2
℃
WITHIN
SPECIFIED
TOLERANCE
TABLE 1 ON
PAGE 13
WIT HIN
ORIGI NAL
LIMIT
2 2HOURS.
-10TO0%OF
INITIAL VALUE
TABLE 1 ON
PAGE 13
N/A
3 25±2
℃
25 MIN .
4 2HOURS.
0 TO +10% OF
INITIAL VALUE
TABLE 1 ON
PAGE 13
WIT HIN 10 X
ORIGI NAL
LIMIT
5 2HOURS.
0 TO +12% OF
INITIAL VALUE
TABLE 1 ON
PAGE 13
WITHIN 12.5X
ORIGI NAL
LIMIT
-55
℃
0
-3
+85
℃
+3
0
+125
℃
+3
0
RATED VOLTAGE 2.5V 4V 6.3V 10V 16 V 20 V 25 V 35V
SURGE VOLTAGE 3.1V 5V 8V 13V 20 V 26V 32 V 45V
V
+
-
R1
R2
S
Cx
+
-
SCL Series
NO ITEMS TEST CONDITION PERFORMANCE
8
DERATING
VOLTAGE
WHEN OPERATING AT HIGH TEMPERATURE RANGE FROM 85℃to 125℃,THE
OPERATION SHALL BE CARRIED OUT AT A DERATED VOLTAGE OR LESS
DERATING VOLTAGE Vt AT ANY TEMPERATURE BETWEEN 85℃AND 125
℃
SHALL BE CALCULATED BY THE FOLLOWING EQUATION
WHERE Vt : DERATED VOLTAGE AT ANY TEMP. BETWEEN 85℃to 125
℃
Vr : RATED VOLTAGE
Vd : DERATED VOLTAGE AT 125
℃
9
ELECTRODE
(TERMINAL
STRENGTH)
APPLY PRESSURE IN THE DIRECTION OF THE
ARROW AT A RATE OF ABOUT 0.5MM/SEC. UNTIL IT
REACHES A BENT WIDTH OF 3MM AND HOLD FOR 30
SEC. THE TEST BOARD SHALL BE
IEC 40(S) 541
.FOR
OTHER PROCEDURES REFER TO
IEC 40(S) 541
.
Pressure rod
THERE SHALL BE NO
EVIDENCE OF
MECHANICAL DAMAGE.
ELECTRICAL
CHARACTERISTICS
SHALL SATISFY THE
INITIAL REQUIREMENT.
IF THERE ARE
ELECTRODES ON BOTH
SURFACES, IT SHALL
SATISFY THE ABOVE
REQUIREMENT ON
WHICHEVER SURFACE
IT MAY BE FIXATED ON.
Vr
Vr Vd
T
=−
−
−4085()
-55 0 20 85 125
100
80
60
40
20
0
OPERATING TEMPERATURE
VOLTAGE
DERATING %
45±245
±
2
Board
20
10
Loading...