Samsung PO24FSSBS User Manual

SyncMaster 242MP

Install Drivers Install Pro

rams

Power

Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment.

Prohibited Important to read and understand at all times

Do not disassemble Disconnect the plug from the outlet

Do not touch Grounding to prevent an electric shock

When not used for an extended period of time, set your computer to DPMS. If using a screen saver, set it to the active screen mode.

Do not use a damaged or loose plug.

z This may cause an electric shock or fire.

Do not pull the plug out by the wire nor touch the plug with wet hands.

z This may cause an electric shock or fire.

Use only a properly grounded plug and receptacle.

z An improper ground may cause electric shock or equipment damage.

Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage.

z This may cause an electric shock or fire.

Do not connect too many extension cords or plugs to an outlet.

z This may cause fire.

Installation

Be sure to contact an authorized service center, when installing your monitor in a location with the heavy dust, high or low temperatures, high humidity, chemical substance and where it operates for 24 hours such as the airport, the train station or etc.

z Failure to do so may cause a serious damage to your monitor.

Put your monitor in a location with low humidity and a minimum of dust.

z Failure to do so may cause an electric shock or fire inside the monitor.

Do not drop the monitor when moving it.

z This may cause damage to the product or human body.

Install the monitor base in a showcase or shelf so that the end of the base does not project beyond the showcase or shelf.

z Dropping the product may cause damage to the product or personal injury.

Set down the monitor carefully.

z The monitor could be damaged or broken.

Do not place the monitor face down.

z The TFT-LCD surface may be damaged.

Installing a wall bracket must be done by a qualified professional.

z Installation by unqualified personnel may result in injury. z Always use the mounting device specified in the owner's manual.

When installing the product, make sure to keep it away from the wall (more than 10cm/4inch ) for ventilation purposes.

z Poor ventilation may cause an increase in the internal temperature of the

product, resulting in a shortened component life and degraded performance.

To prevent rainwater from running along the outdoor antenna cable and entering the house, be sure the outdoor portion of the cable hangs down below the point of entry.

z If rainwater enters the product, it may cause an electric shock or fire.

If you are using an outdoor antenna, be sure to put sufficient distance between your antenna and the electrical wires nearby so that they would not come in contact with each other in case the antenna is knocked over by strong wind.

z A knocked-over antenna may cause injury or an electric shock.

Clean

When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric.

Do not spray water or detergent directly on the monitor.

z This may cause damage, electric shock or fire.

Use the recommended detergent with a smooth cloth.

If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth.

z A dirty connector may cause an electric shock or fire.

Contact the Service Center or Customer Center for interior cleaning once a year.

z Keep the product's interior clean. Dust which has accumulated in the interior

over an extended period of time may cause malfunction or fire.

Others

Do not remove cover (or back).

This may cause an electric shock or fire.

z Refer servicing to qualified service personnel.

If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact

an authorized dealer or service.

z This may cause an electric shock or fire.

Be careful not to let water drip into the monitor or expose the monitor to moisture.

z This may cause malfunction, an electric shock or fire. z Especially avoid operating the monitor near water or outdoors where it could be

exposed to snow or rain.

If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord.

z The monitor may malfunction, causing an electric shock or fire. z Then contact the Service Center .

Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time.

z Failure to do so may cause an electric shock or fire.

Do not try to move the monitor by pulling only the wire or the signal cable.

z This may cause a breakdown, electric shock or fire due to damage to the

cable.

Do not move the monitor right or left by pulling only the wire or the signal cable.

z This may cause a breakdown, electric shock or fire due to damage to the

cable.

Do not cover the vents on the monitor cabinet.

z Bad ventilation may cause a breakdown or fire.

Do not place water containers, chemical products or small metal objects on the monitor.

z This may cause malfunction, an electric shock or fire. z If a foreign substance enters the monitor, unplug the power cord and contact

the Service Center .

Do not use or store inflammable substances near the monitor.

z This may cause an explosion or fire.

Never insert anything metallic into the monitor openings.

z This may cause an electric shock, fire or injury.

Do not insert metal objects such as chopsticks, wire and gimlet or inflammable objects such as paper and match into the vent, headphone port or AV ports.

z It may cause a fire or an electric shock. If an alien substances or water flows

into the product, turn the product off, unplug the power connector from the wall outlet and contact the Service Center.

If you view a fixed screen for an extended period of time, residual image or blurriness may appear.

z Change the mode to energy save or set a screensaver to moving picture when

you need to be away from the monitor for an extended period of time.

Adjust the resolution and frequency to the levels appropriate for the model.

z Inappropriate resolution may cause undesirable picture quality.

24 inch - 1920 X 1200

Keep the volume at a proper level when you use the headphones.

z Excessively loud volume levels may damage hearing.

Watching the monitor continuously at a too close angle may result in eyesight damage.

To ease eye strain, take at least a five-minute break after every hour of using the monitor

Do not use the monitor where it may be exposed to strong vibrations.

z Exposure to strong vibrations may be fire hazard and shorten the life of the

monitor.

When moving the monitor, turn off and unplug the power cord. Make sure that all cables, including the antenna cable and cables connecting to other devices, are disconnected before moving the monitor.

z Failure to disconnect cables may damage it and lead to fire or an electric

shock.

When you remove batteries from the remote, be careful that they are not swallowed by children. Keep batteries out of the reach of children.

z If swallowed, see a doctor immediately.

When replacing batteries, place the batteries in the correct +/- polarity position as indicated on battery holder.

z Incorrect polarity may cause a battery to break or leak and could lead to fire,

injury, or contamination (damage).

Use only specified standard batteries. Do not use new and used batteries together.

z This may cause a battery to break or leak and could lead to fire, injury, or

contamination (damage).

The battery (and rechargeable battery) are not ordinary refuse and must be returned for recycling purposes. The customer is responsible for returning the used or rechargeable battery for recycling purposes as the consumer of the battery.

z The customer can return the used or rechargeable battery to a nearby public

recycling center or to a store selling the same type of the battery or rechargeable battery.

(

)

Unpacking

Please make sure the following items are included with your monitor.

If any items are missing, contact your dealer

Contact a local deale

to buy optional items.

Manual

Cable

Quick Setup Guide

Warranty Card

Not available in all locations

Monitor

User's Guide, Monitor Driver,

Natural Color software

(

)

rSp

D-Sub Cable Power Cord Radio Antenna

Audio Cable

Others

Remote Control Batteries (AAA X 2)

DVI Cable

Connector

For more information >

Connecting TV

Radio Antenna Adapte

Speaker

Option

Speaker Speaker-cove

Speaker Brackets

Use only for the mounting type

installation.

Side cove

Speaker-Audio cable

(Black 4EA, Silver 4EA)

eaker-Stand

Screws

Front

Speaker-Side cove

1. MENU

Use this button to open the on-screen menu and exit from the menu screen or close screen adjustment menu.

2. CH

Moves from one menu item to another vertically or adjusts selected menu values. In TV mode, selects TV channels.

>>Click here to see an animation clip

3. - VOL +

Moves from one menu item to another horizontally or adjusts selected menu values. Adjusts the audio volume.

>>Click here to see an animation clip

4. / FM RADIO

FM RADIO

In PC/DVI mode, sets only SOUND to FM Radio. In general Video SOURCE mode, sets to FM RADIO, turning off the screen. In areas where signal is weak, noise may occur while FM radio is broadcast.

>>Click here to see an animation clip

5. SOURCE

Switches from PC Mode to Video mode. Changing the source is allowed only in external devices that are connected to the monitor at the time. To switch Screen modes: [PC] → [DVI] → [TV] → [Ext.]→ [AV] → [S-Video] → [Component]

>>Click here to see an animation clip

: Activates a highlighted menu item.

: Turns on/off FM Radio.

According to broadcasting type in each country, you may not be able to choose. Scart is mainly used in Europe. For more information > Broadcasting Systems

1. MENU

2. CH

3. - VOL +

4. / FM RADIO

5. SOURCE

6. PIP

7. Power button

8. Power indicator

9. Remote Control Sensor

6. PIP ( Available in PC/DVI Mode Only )

In PC Mode, turns on Video or TV screens in PIP Mode.

>>Click here to see an animation clip

7. Power button

Use this button to turn the monitor on and off.

8. Power indicator

Power Indicator shows PowerSaver mode by green blinking.

9. Remote Control Sensor

Aim the remote control towards this spot on the Monitor.

See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed or when left unattended for long periods.

Rear

Remove the rear monitor cover before connecting to an external device. When it is connected, replace the cover.

(The configuration at the back of the monitor may vary from product to product.)

1. DVI/PC IN

2. COMPONENT IN

1. DVI cable terminal (input)

2. D-SUB(15 pin) cable terminal (input)

3. PC sound terminal (input)

1. DVD/DTV sound input terminal (left/right)

2. DVD/DTV video input terminal (P

, PB,Y)

3. EXT(RGB)

External device terminal

- Scart is mainly used in Europe.

s for EXT(RGB) port of the Monitor, it makes TV or Video

signal input and output.

4. AV IN

5. Headphone / R-SPEAKER-L / ANT IN

1. External device sound input terminal

2. External device (video) input terminal

3. External device (S-video) input terminal

4. FM radio antenna terminall

1. Headphone sound output terminal

2. Speaker sound output terminal

3. TV antenna terminal For more information > Connecting TV

6. POWER

Power terminal This product may be used with 100 ~ 240VAC(+/- 10%).

See Connecting the Monitor for further information regarding cable connections.

Remote Control

The performance of the remote control may be affected by a TV or other electronic device operated near

the monitor, causin

1. POWER

Use this button to turn the monitor on and off.

malfunction due to interference with frequency.

1. POWER

2. Number button

3. +100, -/--

4. - +

5. MUTE

6. TTX/MIX

7. MENU

8. ENTER

9. FM RADIO

10. CH/P

11. SOURCE

12. INFO

13. EXIT

14. Up-Down Left-Right Buttons

15. AUTO

16. P.MODE, M/B (MagicBright™)

17. P.SIZE

18. STILL

19. PIP

20. S.MODE

21. DUAL/MTS

22. PRE-CH

23. SOURCE

24. SIZE

25. POSITION

26. MAGIC-CH

2. Number button

Selects TV channels in the TV mode. You may use this button in PIP mode as well.

3. +100

Press to select channels over 100. For example, to select channel 121, press "+100", then press "2" and "1".

-/-- (One/Two-Digit channel selection )

Use to select a channel numbered ten or over. Press this button, and the "--" symbol is displayed. Enter the two-digit channel number.

-/-- is mainly used in Europe.

4. - +

djusts the audio volume.

5. MUTE

Pauses (mutes) the audio output temporarily. Displays on the lower left corner of the screen. The audio resumes if Mute or - + is pressed in the Mute mode.

6. TTX/MIX

TV channels provide written information services via teletext. For more information > TTX / MIX

TTX / MIX is mainly used in Europe.

7. MENU

Use this button to open the on-screen menu and exit from the menu screen or close screen adjustment menu.

8. ENTER

ctivates a highlighted menu item.

9. FM RADIO

Turns on/off FM Radio. In PC/DVI mode, sets only SOUND to FM Radio. In general Video SOURCE mode, sets to FM RADIO, turning off the screen. In areas where signal is weak, noise may occur while FM radio is broadcast.

10. CH/P

In TV mode, selects TV channels.

11. SOURCE

Switches from PC Mode to Video mode. Changing the source is allowed only in external devices that are connected to the monitor at the time.

12. INFO

Current picture information is displayed on the upper left corner of the screen.

13. EXIT

Exits from the menu screen.

14. Up-Down Left-Right Buttons

Moves from one menu item to another horizontally, vertically or adjusts selected menu values.

15. AUTO

djusts the screen display automatically.(PC MODE)

16. P.MODE, M/B (MagicBright™)

When you press this button, current mode is displayed on the lower center of the screen.

TV / AV / Ext. / S-Video /Component Mode : P.MODE( Picture Mode )

The Monitor has four automatic picture settings that are preset at the factory. Then push button again to circle through available preconfigured modes. ( Dynamic → Standard → Movie → Custom )

PC / DVI Mode : M/B ( MagicBright™ )

MagicBright™ is a new feature providing the optimum viewing environment depending on the contents of the image you are watching. Then push button again to circle through available preconfigured modes. ( Entertain→ Internet → Text → Custom )

17. P.SIZE - Not available in PC/DVI Mode

Press to change the screen size. Panorama, Zoom1, Zoom2 are not available in 1080i(or over 720p) of DTV.

18. STILL

Press the button once to freeze the screen. Press it again to unfreeze.

19. PIP

Push the PIP button to turn PIP screen On/Off.

20. S.MODE ( Sound Mode )

When you press this button, current mode is displayed on the lower center of the screen. The Monitor has a built-in high fidelity stereo amplifier. Then push button again to circle through available preconfigured modes. ( Standard → Music → Movie → Speech → Custom )

21. DUAL / MTS DUAL :

can be operated depending on broadcasting type by using DUAL button on the remote control while watching TV. Toggles MONO/STEREO, DUAL 1/DUAL 2 and MONO/NICAM MONO/NICAM STEREO

MTS :

• Mono, Stereo, SAP (Separate Audio Program) Set 'MTS' to ON to choose Mono, Stereo or SAP.

22. PRE-CH

This button is used to return to the immediately previous channel.

23. SOURCE

Selects the Video source.(PIP Mode)

24. SIZE

You can switch the Picture Size.

25. POSITION

Changes the Position of the PIP window.

26. MAGIC-CH

MagicChannel enables you to watch only certain channels.

This function is available only in Korea.

STEREO/MONO, DUAL l / DUAL ll and MONO/NICAM MONO/NICAM STEREO

You can select the MTS (Multichannel Television Stereo) mode.

Connecting the Monitor

Remove the rear monitor cover before connecting to an external device. When it is connected, replace the cover.

1. Connecting to a Computer

2-1.

2-2.

Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet.

Using the D-sub (Analog) connector on the video card, Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.

Using the DVI (Digital) connector on the video card. Connect the DVI Cable to the DVI Port on the back of your Monitor.

Connect the audio cable for your monitor to the audio port on the back of your computer.

Turn on both your computer and the monitor.

2. Connecting to a Macintosh

You may enjoy clear and quality sound from the computer sound card using the monitor speakers. (You don't need to install any separate speakers for your computer.)

You may get a blank screen depending on the type of video card you are using, if you connect simultaneously both the D-sub and DVI cables to one computer.

If you connect properly your monitor using the DVI connector but get a blank or fuzzy screen, check to see if the monitor status is set to analogue. Press double-check the input signal source.

SOURCE

button to have the monitor

1. Using the D-sub (Analog) connector on the video card, Connect the signal cable to the D-SUB port on the Macintosh computer.

2. For older model Macintoshes, you need to adjust the resolution control DIP switch on the Macintosh adapter (optional) referring to the switch configuration table shown on its rear.

3. Turn on the monitor and Macintosh.

Connecting to other devices

This monitor allows the user to connect it to such input devices as a DVD player, a VCR a camcorder, a DTV or a TV without disconnecting the PC.

The configuration at the back of the monitor may vary from product to product.

1-1. Connecting AV Devices

The monitor has AV connection terminals to connect AV input devices like DVDs, VCRs or Camcorders. You may enjoy AV signals as long as the monitor is turned on.

1. Input devices such as DVDs, VCRs or Camcorders are connected to the Video or S-Video terminal of the monitor using the S-Video cable.

S-Video, RCA cable and EXT(RGB) cable are optional.

2. Connect the Audio (R) and Audio (L) terminals of a DVD, VCR or Camcorders to the monitor's R and L audio input terminals using audio cables.

3. Then, start the DVD, VCR or Camcorders with a DVD disc or tape inserted.

4. Select AV or S-Video using the

1-2. Connecting EXT(RGB) - It only applies to AV DEVICE that supports SCART.

Connect to the DVD Devices input if the device has a DVD connector. You can watch DVD simply by hooking up the DVD with the monitor as long as the power is on.

SOURCE

button on the monitor.

1. Connect a video cable between the EXT(RGB) jacks on the Monitor and the EXT(RGB) jacks on the DVD Player.

2. Select Ext. by pressing

2. Connecting TV

You may view television programs on the monitor if it is connected to an antenna or a CATV cable without installing any separate TV reception hardware or software on your computer.

SOURCE

button on the monitor.

1. Connect the CATV or antenna coaxial cable to the Antenna terminal on the rear of the monitor. You need to use a coaxial antenna cable.

When using an interior antenna terminal:

Check the antenna terminal on the wall first and connect the antenna cable.

When using an outdoor antenna:

If you are using an outdoor antenna, use a professional for installation if possible.

To connect the RF cable to the antenna input terminal:

Keep the copper wire portion of the RF cable straight.

2. Turn on the monitor.

3. Select TV using

4. Select a desired TV channel.

SOURCE

button among the external signal adjustment buttons.

Is weak signal causing poor reception?

Purchase and install a signal amplifier for better reception.

In areas where Antenna cable is not supported, first, attach connector to TV antenna .

3. Connecting DVD/DTV Set Top Box

Connect to the DVD/DTV Set Top Box input if the device has a DVD/DTV connector. You can watch Component simply by hooking up the Component with the monitor as long as the power is on.

+ 44 hidden pages