Samsung PN64E533D2F, PN64E533 User Manual

✎ By connecting the T V to a receiver or home theate r with

Dolby Digital and 5.1ch speakers and selecting Dolby Digital, you can maximize your inter active 3D sound

experience.

■

Audio Delay: Lets you correct timing mismatches between the audio track and the video when you are watching the TV and listening to digital audio output from the TV through an external device such as an AV receiver. When you select Audio Delay, a slider appears. Use the left and right arrow buttons to adjust the slider. Press ENTERE when done (0ms ~ 250ms).

Speaker Settings

■

Speaker Select (External Speaker / TV Speaker)

If you are listening to the sound track of a broadcast or movie through an external receiver, you may hear a sound echo caused by the difference in decoding speed between the TV’s speakers and the speakers attached to your audio receiver. If this occurs, set the TV to External Speaker.

✎ When you set Speaker Select to External Speaker, the

TV’s speakers are turn ed off. You will hear sound throu gh the external speaker s only. When you set Speaker Select to TV Speaker both the TV’s speakers and the ex ternal speakers are on. You will hear sound throu gh both.

✎ When Speaker Select is set to External Speaker, the

VOLUME and MUTE buttons will not operate an d the sound

settings will be limi ted.

✎ If there is no video sign al, both the TV’s speakers a nd the

external speakers will be mute.

Sound Reset

■

Reset All: Resets all sound settings to the factory defaults.

Channel Menu

❑ Memorizing Channels

When you ﬁrst set up your TV using Plug & Play, the TV memorized the channels that were available over the air or through your cable system and added them to the Channel List. The Antenna and Auto program functions described below let you re-run the channel memorization function without having to re-run the Plug & Play procedure.

Antenna (Air / Cable) t

Before your television can memorize the available channels, you must select your TV's signal source, Air (using an antenna) or Cable. Select Menu >Channel > Antenna > Air or Cable. After you have selected the signal source, go on to the Auto Program function.

✎ Selecting the signa l source using the Antenna functi on also

determines the signa l source the TV is tuned to. Fo r example, if you receive your TV s ignal over the air, and you selec t Cable, you will see only snow. You must sele ct Air to see a picture.

Auto Program

The Auto Program function memorizes all channels that are available over the air or through your cable system and adds them to the Channel List.

To start Auto Program, follow these steps:

1. Push MENUm → Channel → ENTERE on your remote. The Antenna Source screen appears.

2. On the Antenna Source screen, select the source of your TV signal.

Air If your TV is connected to an antenna choose Air, and then press

ENTERE. The TV will automatically start memorizing channels.

Cable

If your TV is connected to a cable outlet, choose Cable, and then press ENTERE. Go to Step 3.

Auto

If you choose Auto, and then press ENTERE, the TV will automatically select the correct Antenna source. Go to Step 3.

3. On the Cable Type screen, use the ◄/►/▲/▼ buttons to select the type of digital and analog cable systems you have: STD, HRC, or IRC. Most systems are STD (Standard). When done, select Start, and then press ENTERE. The TV will start memorizing channels.

✎ Channel memoriz ation can take up to 45 minutes, d epending

on your cable system.

✎ Memorized channe ls are added to the Added Channel

list. These are the chan nels you will see when you u se the Channel buttons on yo ur remote.

Clear Scrambled Channel

This function ﬁlters out scrambled channels after Auto Program is completed. This process may take up to 20~30 minutes.

✎ Press the ENTER

button to stop the Clear Scrambled

Channel.

✎ This function is onl y available in Cable mode.

❑ Managing Channels

Channel List

See your list of Added channels, Favorite channels, or channels you've scheduled for viewing. Add or delete Favorite channels, add or delete channels from the Added Channels list, schedule channels or programs for viewing. Watch a channel by selecting the channel in the All Channels, Added Channels, or Favorite screen, pressing the ▲ / ▼ buttons, and then pressing the ENTERE button.

Added Channels

6 Air

6-1 ♥ TV #6

7-1 ♥ TV #7

8 Air 9 Air

9-1 ♥ TV #9

10 Air

10-1 ♥ TV #10 11-1 ♥ TV #11

Air ' Zoom ' Select T Tools ► Next Program

Channel List Screens icons are listed on the left side. Select an icon using the ▲/▼ buttons to view each list.

■

All Channels: Shows all currently available channels including

those you deleted from the Added channels list.

■

Added Channels: Shows all Added channels. These are the

channels that appear when you press the CH button.

■*

Favorite: Shows all favorite channels.

■

Programmed: Shows all channels and programs currently

scheduled using Timer Viewing.

✎ Remote control buttons a ctive on the Channel List screen.

x Green (Zoom): Enlarges or shrinks a channel number. x Yell ow (Select): Move the c ursor to a channel. Pres s the Yellow

button to select the ch annel. A c mark appears. Rep eat to select additional chann els. Then, open the Tools me nu and apply a function to the channels you selected.

(Tool s): Displays the Channel List Too ls men u. (The Tool s

menus may differ depending on the situation.)

Input Source Picture Size

ATV, AV, Component (480i, 480p)

16:9, Zoom1, Zoom2, 4:3

DTV (1080i, 1080p), Component (1080i, 1080p), HDMI (720p, 1080i, 1080p)

16:9, Wide Fit, 4:3, Screen Fit

■

Digital Noise Filter (Off / Low / Medium / High / Auto) : If the broadcast signal received by your TV is weak, you can activate the Digital Noise Filter feature to reduce any static and ghosting that may appear on the screen.

✎ When the signal is weak , try all the Digital No ise Filter

options until the TV di splays the best picture.

■

HDMI Black Level (Normal / Low) : For HDMI signals, select the black level to adjust the screen depth. Low make blacks look darker.

✎ Available only in HDMI mode (RGB signals).

■

Film Mode (Off / Auto) : Sets the TV to automatically sense and process ﬁlm signals from all sources and adjusts the picture for optimum quality.

✎ Available in ATV, DTV (interlace), AV, COMPONEN T (480i /

1080i) and HDMI (480i / 1080i).

■

Screen Burn Protection : To reduce the possibility of screen burn, this unit is equipped with Pixel Shift screen burn prevention technology. Pixel Shift moves the picture slightly on the screen. The Time function setting allows you to program the time between movement of the picture in minutes.

x Pixel Shift ( Off / On) : Using this f unction, you can se t the TV

to move pixels minutely o n the PDP screen in a ho rizontal or vertical direc tion to minimize af ter images on the scr een.

Available Pixel Shift Settings and Optimum Settings

Available Settings Optimum Settings

Horizontal 0~4 (pixels) 4

Vertical 0~4 (pixels) 4

Time

(minute)

1~4 min 4 min

✎ The Pixel Shift value may differ de pending on the

monitor size (inches) and mode.

✎ This function is not avai lable in the Screen Fit mode.

Your TV also has the following additional screen burn protection functions:

x Scrolling: This functi on removes after-imag es on the screen

by illuminating all th e pixels on the PDP accord ing to a pattern. Use this function whe n there are after imag es or symbols on the screen, especi ally when you displa yed a still image on the screen for a long time.

✎ The after-image removal f unction has to run a long tim e

(approximately 1 hour) to rem ove after-images on the screen effective ly. If the after-image is not removed af ter you run the function, run the function again.

✎ Press any key on the remote cont rol to cancel this

feature.

x Side Grey (Dark/Light): Lets you select the c olor of the

sidebars your TV d isplays when you set th e screen size to 4:3.

■

Picture Reset (Reset Picture Mode/Cancel): Resets the picture settings to their factory defaults.

Sound Menu

Mode

■

Standard: Selects the normal sound mode.

■

Music: Emphasizes music over voices.

■

Movie: Provides the best sound for movies.

■

Clear Voice: Emphasizes voices over other sounds.

■

Amplify: Increase the intensity of high-frequency sounds to allow a better listening experience for the hearing impaired.

Equalizer

Available in Standard sound mode only.

■

Balance L/R: Adjusts the balance between the right and left speaker.

■

100Hz / 300Hz / 1KHz / 3KHz / 10KHz (Bandwidth Adjustment): Adjusts the loudness of speciﬁc bandwidth frequencies.

■

Reset: Resets the equalizer to its default settings.

SRS TruSurround HD (On/Off)

Available in Standard sound mode only.

SRS TruSurround HD is a patented SRS technology that solves the problem of playing 5.1 multichannel content through two speakers. TruSurround delivers a compelling, virtual surround sound experience through any two-speaker playback system, including internal television speakers. It is fully compatible with all multichannel formats.

Preferred Language

Digital channels only.

Digital-TV broadcasts can transmit many audio tracks simultaneously (for example, simultaneous translations of a program into foreign languages).

✎ You can only select a langu age from among the ones be ing

broadcast.

Multi-Track Sound (MTS)

Analog channels only.

■

Mono: Select for channels that are broadcasting in mono or if you are having difﬁculty receiving a stereo signal.

■

Stereo: Select for channels that are broadcasting in stereo.

■

SAP: Select to listen to the Separate Audio Program, which is usually a foreign-language translation.

✎ Depending on the prog ram being broadcast, yo u can listen to

Mono, Stereo or SAP.

Auto Volume

Because each station has its own broadcasting conditions, the volume may ﬂuctuate each time you change the channel. This feature automatically adjusts the volume of a channel by lowering the sound output when the modulation signal is high or by raising the sound output when the modulation signal is low.

SPDIF Output

The SPDIF (Sony Philips Digital InterFace) outputs an uncompressed digital audio signal when you connect the digital audio jack on the back of the TV to a digital audio in jack on a receiver or home theater.

■

Audio Format (PCM/Dolby Digital): You can select the Digital Audio output (SPDIF) format. The available Digital Audio output format may differ depending on the input source.

Display Icons Used in the Channel List Screens

Icons Meaning

A selected channel.

A Favorite channel.

)

A reserved program.

(

A program currently being broadcast.

❑ The Channel List Tools Menu

The Channel List Tools menu contains most of the functions you can use on the

All Channel, Added Channels

, and

Favorite List screens. To view, select a list screen, select a channel, and then press the

TOOLS

button.

■

Add / Delete: Delete a channel from or add a channel to the Added Channels list.

To delete channels from the Added Channels list, follow these steps:

1. Select one or more channels in the Added Channels list using the ▲/▼ buttons and the Yellow Select button on your remote.

2. Press the TOOLS button on your remote. The Tools menu appears.

3. Select Delete in the Tools menu, and then press the

ENTERE button.

To add channels to the Added Channels list, follow these steps:

1. Select one or more channels in the All Channels list using the ▲/▼ buttons and the Yellow Select button on your remote.

2. Press the TOOLS button on your remote. The Tools menu appears.

3. Select Add in the Tools menu, and then press the ENTERE button.

✎ All deleted channel s will be shown on the All Channels list.

You add channels back to the Added Channels list on th e All Channels list.

✎ A gray-colored chann el indicates the chann el has been

deleted from the Added Channels list.

✎ The Add menu option only ap pears for deleted cha nnels.

■

Add to Favorite/Delete from Favorite t: Lets you add channels to and delete channels from your Favorites list.

To add channels to the Favorites list, follow these steps:

1. Select one or more channels in the All Channels list using the ▲/▼ buttons and the Yellow Select button on your remote.

2. Press the TOOLS button on your remote. The Tools menu appears.

3. Select Add to Favorite in the Tools menu, and then press the

ENTERE button.

To delete channels from the Favorites list, follow these steps:

1. Select one or more channels in the Favorite Channels list using the ▲/▼ buttons and the Yellow Select button on your remote.

2. Press the TOOLS button on your remote. The Tools menu appears.

3. Select Delete from Favorite in the Tools menu, and then press the ENTERE button.

■

Timer Viewing: You can schedule a channel to be displayed automatically at a set time, even when you are watching another channel. You must set the current time ﬁrst in the Time > Clock function to use Time Viewing.

To schedule a channel, follow these steps:

1. Select a channel in the Added Channels list using the ▲/▼ buttons and the Yellow Select button on your remote.

2. Press the TOOLS button on your remote. The Tools menu appears.

3. Select Time Viewing in the Tools menu, and then press the

ENTERE button. The Time Viewing screen appears.

Antenna Channel Repeat

▲

DTV Air 6-1 Once

▼

Move U Adjust E Enter R Return

Timer Viewing

Date Start Time

01-01-2012 12 : 01 am

4. Use the ◄/► buttons to move from entry ﬁeld to entry ﬁeld and the ▲/▼ buttons to change the entries. Where numbers are displayed, you can also enter numbers directly using the number keypad on your remote.

✎ If you select Everyday or E very Week, the date yo u

select in the Date fiel d becomes the start d ate for your scheduled viewin g. For Everyday, the TV will turn o n every day, at the time you selec ted, starting from that date. For Everyweek, the T V will turn on every wee k, on the same day of the week as th e start date you selected, at the time you se lected, from that day on. If you select Once, the TV will tu rn on once, on the date and time you selected.

5. Press the ENTERE button on your remote when done.

✎ Only Added channels can be scheduled. ✎ Scheduled programs and channels are displayed in the

Programmed List.

✎ When you select a digi tal channel, press the ► b utton to

view the digital progr am list. If you highlight a pro gram in the list, and then press th e ENTERE(Schedule) button, you set Timer Viewing for that program directly.

■

Select All: Select all the channels in the displayed channel list.

■

Deselect All: Deselect all the selected displayed channels.

✎ You can only select Deselect All when one or m ore

channels are selected.

■

Channel Name Edit: Analog channels only. Lets you assign a name of up to ﬁve characters to an analog channel. For example, Hist, Food, Golf, etc. This makes it easier to ﬁnd and select a channel .

■

Auto Program: See Auto Program under Memorizing Channels.

Programmed List (on the Channel List Screen)

The Programmed list displays the channels and programs you have scheduled for viewing using the Time Viewing function. You can view, modify, or delete a show you have scheduled using the functions on the Programmed List screen Tools menu.

Programmed List Screen Tools Menu

■

Change Info: Change the scheduling information for a show or channel you have scheduled.

To change the information, follow these steps:

1. Select the Programmed List icon on the left side of the Channel List screen, and then press the ENTERE button.

2. On the Programmed List screen, select the show or channel entry you want to change, and then press the TOOLS button. The Tools Menu appears.

3. Select Change Info, and then press the ENTERE button. The Time Viewing screen appears.

5. Press the ENTERE button when done.

■

Cancel Schedules: Cancel a show or channel you have scheduled.

To cancel a scheduled show or channel, follow these steps:

1. Select the Programmed List icon on the left side of the Channel List screen, and then press the ENTERE button.

2. On the Programmed List screen, select the show or channel entry you want to cancel, and then press the TOOLS button. The Tools Menu appears.

3. Select Cancel Schedules, and then press the ENTERE button. The Cancel Schedule screen appears.

4. Select OK, and then press the ENTERE button.

■

Information: Display the information for a show or channel you have scheduled. You can also change the schedule Information.

1. Select the Programmed List icon on the left side of the Channel List screen, and then press the ENTERE button.

2. On the Programmed List screen, select the show or channel entry you want information for, and then press the TOOLS button. The Tools Menu appears.

3. Select Information, and then press the ENTERE button. The Time Viewing Information screen appears.

4. Select Change Info and press the ENTERE button to change information, or select Close and press the

ENTERE button to close the Information screen.

■

Select All / Deselect All: You can select or deselect all channels in the channel list.

❑ Other Channel Menu Functions

Channel Mode (Added Channels/Favorite Channels)

Lets you select the channel list displayed when you press the <CH>(Channel) button on your remote. For example, if you select Favorite Channels, you will only see Favorite channels when you press the <CH> button.

Fine Tune

Analog channels only.

If the reception is clear, you do not have to ﬁne tune the channel, as this is done automatically during the search and store operation. If the signal is weak or distorted, ﬁne tune the channel manually.

✎ Select the channel, a nd then select Fine Tune. ✎ Fine tuned channel s that have been saved are mar ked with

an asterisk “*” on the righ t-hand side of the channel n umber in the channel banne r.

✎To reset fine-tunin g, select the channel, s elect Fine Tune, and

then select Reset on the Fine Tune screen.

Setup Menu

Plug & Play

Lets you re-run the Plug & Play initial setup procedure. For instructions, see your Quick Start Guide.

Language

Set the menu language.

✎ Choose between English, Español, and Français.

❑ Setting the Time

Time

✎ The time you set will appe ar when you press the INFO

button.

■

Clock: Set the clock so you can use the various timer features of the TV.

✎ If you disconnect the pow er cord, you have to set the

clock again.

To set the clock, follow these steps:

1. Select Setup >Time > Clock.

2. Press ENTERE and select Auto or Manual, and then press

ENTERE again.

If you selected Auto:

The TV will automatically download the correct time from a digital channel.

• Select Time Zone, and then press the ENTERE button. Use the▲/▼ buttons to select your Time Zone, and then press ENTERE.

• Select DST (Daylight Savings Time), and then press

ENTERE. Select On if you want to turn the DST

adjustment on and off manually. Select Off to turn off the DST adjustment. Select Auto if you want the TV to adjust to DST automatically. Press ENTERE when done.

✎ DST and Time Zone function are only availa ble when

the Clock Mode is set to Auto.

If you selected Manual:

The Clock Set screen appears. Use the ▲/▼ buttons to change the values in each ﬁeld or use the number buttons to enter the values directly. Use the ◄/► buttons to move from ﬁeld to ﬁeld. When done with all the ﬁelds, press ENTERE.

✎ Available only when Clock Mode is set to Manual.

■

Sleep Timer

Automatically shuts off the TV after a preset period of time. (30, 60, 90, 120, 150 and 180 minutes).

✎ To cancel the Sleep Timer, select Off.

Timer 1 / Timer 2 / Timer 3

Turns the TV on and off automatically at times and days you select. You can set three different on/off timer settings.

✎ You must set the clock first.

■

On Time / Off Time: Set the hour, minute, am/pm, and Activate/Inactivate ﬁelds for the On Time and Off Time. Use the ◄/► buttons to move from ﬁeld to ﬁeld. Use the ▲/▼ buttons to change the values in each ﬁeld. To activate the timer with the setting you have chosen, set the Activate/Inactivate ﬁeld to Activate.

■

Volume: Set the desired loudness.

Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance. Product design and speciﬁcations may be changed without notice.

Important Warranty Information Regarding Television Format Viewing

✎ See the warranty ca rd for more informati on on warranty ter ms.

Wide screen format PDP Displays (with 16:9 aspect ratios, the ratio of the screen width to height) are primarily designed to view wide screen format full-motion video. The images displayed on them should primarily be in the wide screen 16:9 ratio format, or expanded to ﬁll the screen if your model offers this feature, with the images constantly in motion. Displaying stationary graphics and images on the screen, such as the dark sidebars on non-expanded standard format television video and programming, should be limited to no more than 5% of the total television viewing per week. Additionally, viewing other stationary images and text such as stock market crawls, video game displays, station logos, web sites or computer graphics and patterns, should be limited as described above for all televisions. Displaying stationary images for more than 5% of total viewing time can cause uneven aging of your PDP display and leave subtle, but permanent burned-in ghost images in the PDP picture. To avoid this, vary the programming and images, and primarily display full screen moving images, not stationary patterns or dark bars. On PDP models that offer picture sizing features, use these controls to view different formats as a full screen picture. Be careful in the selection of television formats you use for viewing and the amount of time you view them. Uneven PDP aging as a result of format selection and use, as well as burned in images, are not covered by your Samsung limited warranty.

•SAMSUNGELECTRONICSNORTHAMERICANLIMITEDWARRANTY

STATEMENT Subject to the requirements, conditions, exclusions and limitations of the original Limited Warranty supplied with Samsung Electronics (SAMSUNG) products, and the requirements, conditions, exclusions and limitations contained herein, SAMSUNG will additionally provide Warranty Repair Service in the United States on SAMSUNG products purchased in Canada, and in Canada on SAMSUNG products purchased in the United States, for the warranty period originally speciﬁed, and to the Original Purchaser only. The above described warranty repairs must be performed by a SAMSUNG Authorized Service Center. Along with this Statement, the Original Limited Warranty Statement and a dated Bill of Sale as Proof of Purchase must be presented to the Service Center. Transportation to and from the Service Center is the responsibility of the purchaser. Conditions covered are limited only to manufacturing defects in material or workmanship, and only those encountered in normal use of the product. Excluded, but not limited to, are any originally speciﬁed provisions for, inhome or on-site services, minimum or maximum repair times, exchanges or replacements, accessories, options, upgrades, or consumables. For the location of a SAMSUNG Authorized Service Center, please call toll-free: – In the United States : 1-800-SAMSUNG (1-800-726-7864) – In Canada : 1-800-SAMSUNG

Important User Information

•Screen Image retention

Do not display a still image (such as that from a video game) on the plasma display panel for more than a few minutes. Still images can cause screen image retention (burn in). To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image.

•Heat on the top of the Plasma TV

The top side of the TV may become hot after long periods of use as heat dissipates from the panel through the vent hole in the upper part of the TV. This is normal and does not indicate any defect or operational failure of unit.

However, children should be prevented from touching the upper part of the TV.

•The TV is making a ‘cracking’ noise.

A ‘cracking’ noise may occur when the TV contracts or expands due changes in the surrounding environment such as temperature or humidity. This is normal and not a defect.

•Cell Defects

Your plasma TV has a panel containing 2,360,000 (HD-level) to 6,221,000 (FHD-level) pixels which require sophisticated technology to produce. However, there may be a few bright or dark pixels on the screen. These pixels will have no impact on the performance of the product.

•Avoid operating the TV at temperatures below 41°F (5°C)

•A still image displayed too long may cause permanent damage to the

PDP Panel.

Watching the Plasma TV in 4:3 format for a long period of time may leave traces of the borders on the left, right, top, or bottom of the screen. Playing a DVD or a game console may have a similar effect. Damage caused by the above effect is not covered by the warranty.

•After-images on the Screen.

Displaying still images from Video games or a PC for longer than a certain period of time may produce partial after-images. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images for a long time.

•Warranty

Warranty does not cover any damage caused by image retention. Burn-in is not covered by the warranty.

•Caution

The glass screen of your PDP TV can break if you accidently drop the TV. Handle the TV with care. When moving the TV, always have two or more people pick it up and carry it as a safety precaution. Do not lay the TV ﬂat on its face or back.

Your Samsung Plasma TV is a high quality television that has been carefully packaged to protect the integrity of its glass panel and component parts during shipment. It is, nonetheless, a fragile piece of electronics that requires careful handling. Refrain from putting undue stress on any part of the packaging when shipping or unpacking the TV. Use care when installing the TV. Avoid placing the TV in a location where it may be struck, exposed to sharp impacts, or fall. Panel breakage caused by a fall or impact strike is not covered under the manufacturer’s warranty.

BN68-04647A-00

Plasma TV

user manual

The On Screen Menus

Your TV has two kinds of menus, the Main menu and the various Tools menus. The Main menu gives you access to most or all of the menu options available on your TV. The Tools menus display a selected number of frequently used menu options that change depending on the screen you are viewing. A Tools menu symbol (T) in the lower right side of the screen indicates that a Tools menu is available.

The Main menu has seven primary categories:

y Picture y Input

y Sound y Application

y Channel y Support

y Setup

To view the Main menu, press the MENU button on your remote. To view a Tools menu, press the TOOLS button on your remote.

✎ The menu options that ap pear in the Main menu de pend

on the Source you have sele cted. For example, if you have selected the HDMI sour ce, the Channel categor y will not appear. To see the Channel catego ry, you must first select T V in the Source List.

The Menu options are presented below, arranged by Main menu categories. A Tools button symbol (

) next to an option

name indicates the option is also available in one of the Tools menus.

Picture Menu

Mode

Select your preferred picture mode.

✎ When your TV is conne cted to a PC, you can only selec t

Entertain and Standard.

■

Dynamic: Brightens the screen. Suitable for a bright room.

■

Standard: Suitable for a normally lit room.

■

Movie: Darkens the screen, making it less glary. Suitable for watching movies in a darkened room.

■

Entertain: Sharpens the picture. Suitable for games.

✎ Only available when t he TV is connected to a PC.

Cell Light / Contrast / Brightness / Sharpness / Color / Tint (G/R)

■

Cell Light: Adjusts the brightness of the screen by adjusting the brightness of the individual pixels.

■

Contrast: Increases or decreases the contrast between dark and light areas of the picture.

■

Brightness: Adjusts the brightness of the screen. Not as effective as Cell Light.

■

Sharpness: Sharpens or dulls the edges of objects.

■

Color: Adjusts the color saturation. The higher the Color setting, the more intense the color. Low settings remove color and the picture becomes black, white, and gray.

■

Tint: Adjusts the amount of green and red in the picture. As you increase the amount of green, the amount of red decreases and vice versa.

✎ When the TV is conne cted to a PC, you can only make

changes to Cell Light, Contrast, Brightness, and

Sharpness.

Advanced Settings

Available in Standard and Movie mode only.

Compared to previous models, new Samsung TVs offer a more precise picture with more precise controls.

✎ When your TV is conne cted to a PC, you can only make

changes to Gamma and White Balance.

■

Color Space (Auto / Native): Auto automatically matches the range of colors available to create pictures to the color range of the video source. Native provides a color range wider than the color range of the video source.

■

White Balance: Adjusts the color temperature of the picture so that white objects look white (instead of, for example, slightly pink or slightly yellow) and the overall color of the picture looks natural.

R-Offset / G-Offset / B-Offset: Adjusts each color’s (red, green, blue) darkness. R-Gain / G-Gain / B-Gain: Adjusts each color’s (red, green, blue) brightness. Reset: Resets the White Balance to it’s default settings.

■

Gamma: Adjusts the primary color intensity.

■

Dynamic Contrast (Off / Low / Medium / High): Adjusts the screen contrast.

■

Black Tone (Off / Dark / Darker / Darkest): Selects the black level to adjust the screen depth. Darker settings make blacks look darker.

■

Flesh Tone: Adjusts the amount of red in skin tones.

■

Motion Lighting (Off / On): When on, the TV automatically adjusts the brightness of the screen in response to the brightness of the room. In bright light, the screen brightens. In dim light, the screen dims.

✎ Available in Standard mode only.

Picture Options

✎ When the TV is conne cted to a PC, you can only make

changes to the Color Tone, Size and HDMI Black Level.

■

Color Tone (Cool / Standard / Warm1 / Warm2): Cool makes the picture bluer (cooler). Warm 1 and Warm 2 make the picture redder (warmer).

✎ Warm1 and Warm2 ar e deactivated when the pi cture

mode is set to Dynamic.

■

Size: Set the size and aspect ratio of the picture on the screen. Your cable box or satellite receiver may have its own set of screen sizes as well. However, we highly recommend you use the TV's 16:9 mode most of the time.

16:9: Sets the picture to the 16:9 wide screen format. Zoom1: Provides moderate magniﬁcation of the picture. Sides,

top, and bottom are cut off. Zoom2: Provides larger magniﬁcation of the picture. Sides, top, and bottom are cut off. Wide Fit: Enlarges the aspect ratio of the picture so the picture ﬁts the entire screen. 4:3: Sets the picture to the old, 4:3 format and puts black or gray borders on the right and left of the picture.

✎ Do not watch your TV in the 4:3 forma t for a long time.

Traces of borders displayed o n the left, right and cen ter of the screen may cause ima ge retention (screen bur n) which

is not covered by the warran ty. Screen Fit: Displays the full image without any cut-off when your TV is inputting HDMI (720p / 1080i / 1080p) or Component (1080i / 1080p) HD signals.

✎ HD (High Definition) h as a 16:9 aspect ratio and 1080i/1080p

(1920x1080) or 720p (1280x720) resolution.

✎ You can adjust and store settin gs for each external dev ice you

have connected to an input o n the TV. Picture Sizes available by Input Source are listed above and to the right:

■

Contents: To select what will be turned on when the timer setting is activated. You can set the TV to turn on a speciﬁc channel or play back contents such as photo or audio ﬁles. Use the ◄/► buttons to move to move to the Contents ﬁeld, and then press the ENTERE button. The Contents screen appears. Use the ◄/► buttons to move from ﬁeld to ﬁeld. Use the ▲/▼ buttons to change the values in each ﬁeld.

- TV/USB: Select TV or USB. The USB device must be connected to your TV before you can select USB.

- Antenna: Displays the current antenna source, Air or Cable.

- Channel: If you have selected TV, select the desired channel.

- Music/Photo: If you have selected USB, follow these steps to

select a folder containing MP3 (Music) or JPEG (Photo) ﬁles on the USB device:

✎ The maximum displayed number of files, including sub

folders, in one folder o f USB storage device is 200 0.

✎ The media may not be playi ng smoothly when usin g the

device lower than USB 2.0.

1. Use the ◄/► buttons to move to the ﬁeld under Music

or the ﬁeld under Photo, and then press the ENTERE button. The TV displays a single folder (the Root folder) and the type or name of the device.

2. Press the ENTERE button. A list of folders on the device

appears.

✎ If there are no folders on yo ur device, press the

Yello w select button to se lect the Root folder, and then press the RETURN button. The T imer screen re-appears.

3. Use the ▲/▼ buttons to highlight a folder that contains

music or photos, and then press the Yellow select button to select the folder.

4. Press the RETURN button. The Timer screen re-appears.

■

Repeat: Select Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun or Manual. If you select Manual, you can select the days you want to activate the timer by using the ◄/► buttons to highlight the day, and then pressing the ENTERE button. To unselect a

day, highlight it, and then press the ENTERE button. When you ﬁnished making all your selections on the Timer screen, press either the ENTERE or RETURN button.

❑ Other Features

Program Rating Lock

The Program Rating Lock feature lets you block programs you've determined are inappropriate for your children based on the program's ratings. To access the Program Rating Lock feature and make any changes, you must enter a PIN (personal identiﬁcation number). To watch a blocked program, you must also enter the same PIN.

✎ Program Rating Lock is not available in HDMI or

Component mode.

✎ The default PIN numbe r of a new TV set is “0-0- 0-0”. You can

set your own PIN using the Change PIN function.

How It Works

When you access the Program Rating Lock Menu functions for the ﬁrst time, the PIN input screen appears. Enter 0-0-0-0. The PIN screen closes and the Program Rating Lock Menu appears. Every time you access the Program Rating Lock functions, the PIN screen will appear and you must enter a PIN.

When the Rating Lock screen appears, select Program Rating

Lock, and then press ENTERE. Select ON, and then press the

ENTERE key again. Depending on what type of programs or

movies you want to block, select one of the options on the screen, and then press the ENTERE button. The options are listed below:

■

TV Parental Guidelines: You can block TV programs based on their ratings. This function allows you to control what your children are watching.

■

MPAA Rating: You can block movies based on their MPAA ratings. The Motion Picture Association of America (MPAA) has implemented a rating system that provides parents or guardians with advanced information on which ﬁlms are appropriate for children.

■

Canadian English: You can block TV programs based on their Anglophone Canadian ratings.

■

Canadian French: You can block TV programs based on their French Canadian ratings.

■

Downloadable U.S. Rating: Parental restriction information can be used while watching DTV channels.

Locking/Blocking Programs or Movies

You lock or block programs and/or movies in essentially the same way for each option. Each option displays a grid or table. All the tables have ratings listed on the left. The TV Parental Guidelines option also has kinds of content listed across the top: ALL: Lock all TV ratings. / FV: Fantasy violence / V: Violence / S: Sexual situation / L: Adult Language / D: Sexually Suggestive Dialog.

To lock/block movies or shows with certain ratings and/or kinds of content, click the square next to the rating and/or under the kind of content. A lock appears. To unlock/unblock, click the square again. When you click a low rating, all the ratings above it will also display locks. You can also Allow All or Lock All. When done, press the

RETURN button on your remote.

■

Change PIN: The Change PIN screen will appear. Choose any 4 digits for your PIN and enter them in Enter New PIN ﬁelds. Re-enter the same 4 digits in Conﬁrm New PIN ﬁelds. When the Change PIN screen disappears, press the OK button. The TV has memorized your new PIN.

✎ If you forget the PIN, press the r emote-control button s in

the following sequen ce, which resets the pin to “0 -0-0-0” :

POWER (off) → MUTE → 8 → 2 → 4 → POWER (on)

Game Mode (On/Off)

When you connect a game console such as a PlayStation™ or Xbox™ to your TV, you can enjoy a more realistic gaming experience by turning on the Game Mode function.

✎ Precautions and limi tations for game mode:

x Before you disconnect the game console and connect another

external device, se t Game Mode to Off in the setup menu.

x If you display th e TV menu in Game Mode, the screen shake s

slightly.

✎ Game Mode is not available when the inp ut source is set to

TV.

✎ After connecting the game console, set Game Mode to On.

You may notice slightly reduced picture quality.

Caption

(On-Screen Text Dialogue)

■

Caption: You can switch the caption function on or off. If captions are not available, they will not be displayed on the screen.

✎ The Caption feature does not wor k in Component or

HDMI mode.

■

Caption Mode: You can select the desired caption mode.

Default / CC1~CC4 / Text1~Text4: (analog channels only) The

Analog Caption function operates in either analog TV channel mode or when a signal is supplied from an external device to the TV. (Depending on the broadcasting signal, the Analog Caption function may or may not work with digital channels.)

Default / Service1~Service6 / CC1~CC4 / Text1~Text4: (Digital channels only) The Digital Captions function works with digital channels.

✎ Serv ice1~6 may not be available in di gital caption mode

depending on the broa dcast.

■

Digital Caption Options: (Digital channels only) Size: Options include Default, Small, Standard and Large. The

default is Standard. Font Style: Options include Default and Styles 0 to 7. The default is Style 0. Foreground Color: Options include Default, White, Black, Red, Green, Blue, Yellow, Magenta and Cyan. You can change the color of the letters. The default is White. Background Color: Options include Default, White, Black, Red, Green, Blue, Yellow, Magenta and Cyan. You can change the background color of the captions. The default is Black. Foreground Opacity: This adjusts the opacity of text. Options include Default, Transparent, Translucent, Solid and Flashing. Background Opacity: This adjusts the opacity of the caption background. Options include Default, Transparent, Translucent, Solid and Flashing. Return to Default: This option sets each Size, Font Style, Foreground Color, Background Color, Foreground Opacity and Background Opacity to its default.

✎ Digital Caption Options are available only whe n you can

select Default and Servi ce1 ~ Service6 in Caption Mode.

✎ The Foreground and Ba ckground cannot be set to the s ame

colo r.

Melody

Lets you control whether a melody plays when the TV is turned on or off.

✎ The Melody does not play:

x When no sound i s output from the TV b ecause the MUTE button

has been pressed.

x When no sound i s output from the TV b ecause the volume ha s

been reduced to mini mum with the VOL – button .

x When the TV i s turned off by the Sle ep Timer function.

Auto Protection Time

■

Auto Protection Time (Off / 10 min / 20 min / 40 min / 1 hour): If the screen remains idle with a still image for a certain period of time you deﬁne, the screen saver is activated to prevent the formation of ghost images on the screen.

Eco Solution

■

Energy Saving (Off / Low / Medium / High / Picture Off) : This adjust the brightness of the TV in order to reduce power consumption. If you select Picture Off, the screen is turned off, but the sound remains on. Press any button except the volume button to turn on the screen.

■

Eco Sensor (Off / On) : To enhance power savings, the picture settings will automatically adapt to the light in the room.

✎ If you adjust Cell Light in the Picture me nu, the Eco Sensor

will be set to Off. Min Cell Light : When Eco Sensor is On, you can manually adjust the minimum screen brightness.

✎ If Eco Sensor is On, the display brightness m ay change

(become slightly da rker or brighter) depe nding on the light

intensity in your room. You can c ontrol the screen’s minimum

brightness with the Min Cell Light function.

■

No Signal Power Off (Off / 15 min. / 30 min. / 60 min.): Sets how quickly the TV switches to standby mode, if no picture is being received.

✎ Disabled when the PC i s in power saving mode.

■

Auto Power Off (Off / On): The TV will be automatically turned off when no user operation is detected for 4 hours.

Support Menu

Self Diagnosis

■

Picture Test: Use to check for picture problems. If the problem appears in the test picture, select Yes and follow the directions on the screen.

■

Sound Test: Use the built-in melody sound to check for sound problems. If the problem occurs during the test, select Yes and follow the directions on the screen.

■

Signal Strength: (Digital channels only) An HD channel’s reception quality is either perfect or the channels are unavailable. Adjust your antenna to increase signal strength.

■

Reset: Reset all settings to the factory defaults.

✎ The PIN input screen ap pears before the setup sc reen. ✎ Enter your 4-digit PIN. Cha nge the PIN using the Chan ge

PIN option.

Software Upgrade

Software Upgrade can be performed by downloading the latest ﬁrmware from samsung.com to a USB memory device.

HD Connection Guide

Refer to this information when connecting external devices to the TV.

Contact Samsung

View this information when your TV does not work properly or when you want to upgrade the software. You can ﬁnd information regarding our call centers and how to download products and software.

Media Play

Enjoy photos, music and/or movie ﬁles saved on a USB Mass Storage Class (MSC) device.

POWER

MEDIA.P

❑ Connecting a USB Device

1. Turn on your TV.

2. Connect a USB device containing photo, music, and/or movie ﬁles to the USB jack on the back of the TV. A pop up window appears.

3. Press the MEDIA.P button on your remote. The Media Play menu

appears.

❑ Using the Media Play Menu

SUM

■

Change Device

Enter R Return

Media Play

Videos

To open Media Play in the Menu, follow these steps:

1. Press the MENU button. Then, press the ▲ or ▼ button to select Application on the left, and then press the ENTERE button.

Contact SAMSUNG WORLDWIDE

If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.

Country CANADA U.S.A.

Address

Samsung Electronics Canada Inc., Customer Service 55 Standish Court Mississauga, Ontario L5R 4B2 Canada

Samsung Electronics America, Inc. 85 Challenger Road Ridgeﬁeld Park, NJ 07660

Customer Care Center



1-800-SAMSUNG(726-7864)

Web Site

www.samsung.com/ca (English)

www.samsung.com/ca_fr (French)

www.samsung.com

- 2 -- 1 -

- 6 -- 5 -

- 3 -

- 7 -

- 4 -

- 8 -

[PE533-ZA]BN68-04647A-ENG.indd 1 2012-08-07 �� 2:01:22

Kensington Lock

The Kensington Lock is not supplied by Samsung. It is a device used to physically ﬁx the system when using it in a public place. Refer to the manual provided with the Kensington Lock for additional information on proper use.

✎ Please find a “

” icon on the rear of the TV. The Ken sington

slot is beside the “K” icon.

✎ The position and col or may differ depend ing on the model.

To lock the product, follow these steps:

1. Wrap the Kensington lock cable around a large, stationary object

such as desk or chair.

2. Slide the end of the cable with the lock attached through the looped end of the Kensington lock cable.

3. Insert the locking device into the Kensington slot on the product.

4. Lock the lock.

✎ These are general in structions. For exact in structions, see the

User manual suppli ed with the locking devi ce.

✎ The locking device h as to be purchased separ ately. ✎ The location of the Kensi ngton slot may be differe nt depending

on the TV model.

Display Modes (HDMI/DVI Input)

Optimal resolution is 1920 x 1080@60Hz.

Mode Resolution

Horizontal

Frequency (KHz)

Vertical Frequency

(Hz)

Pixel Clock

Frequency (MHz)

Sync Polarity

(H / V)

IBM

640 x 350 31.469 70.086 25.175 +/ 720 x 400 31.469 70.087 28.322 -/+

MAC

640 x 480 35.000 66.667 30.240 -/832 x 624 49.726 74.551 57.284 -/-

1152 x 870 68.681 75.062 100.000 -/-

VESA DMT

640 x 480 31.469 59.940 25.175 -/ 640 x 480 37.861 72.809 31.500 -/ 640 x 480 37.500 75.000 31.500 -/ 800 x 600 37.879 60.317 40.000 +/+ 800 x 600 48.077 72.188 50.000 +/+

800 x 600 46.875 75.000 49.500 +/+ 1024 x 768 48.363 60.004 65.000 -/1024 x 768 56.476 70.069 75.000 -/1024 x 768 60.023 75.029 78.750 +/+ 1152 x 864 67.500 75.000 108.000 +/+ 1280 x 720 45.000 60.000 74.250 +/+ 1280 x 800 49.702 59.810 83.500 -/+ 1280 x 1024 63.981 60.020 108.000 +/+ 1280 x 1024 79.976 75.025 135.000 +/+ 1366 x 768 47.712 59.790 85.500 +/+ 1440 x 900 55.935 59.887 106.500 -/+

1600 x 900RB 60.000 60.000 108.000 +/+

1680 x 1050 65.290 59.954 146.250 -/+ 1920 x 1080 67.500 60.000 148.500 +/+

2. Press the ▲ or ▼ button to select Media Play (USB), and then press the ENTERE button.

3. Press the ◄ or ► button to select an icon (Videos, Music, Photos, Settings), and then press the ENTERE button.

✎ Media Play might not work p roperly with unlice nsed

multimedia files.

✎ Need-to-Know List bef ore using Media Play (US B)

x The file syste m supports FAT16, FAT32 and NTFS. x Certain t ypes of USB Digital c amera and audio dev ices may not

be compatible with thi s TV.

x Media Play onl y supports USB Mas s Storage Class (MSC)

devices. MSC is a Mass S torage Class Bulk-On ly Transport device. Examples o f MSC are Thumb drives a nd Flash Card Readers. Devices s hould be connecte d directly to the TV’s USB port. USB HDD is not supported.

x Before conne cting your device to the T V, please back up your

files to prevent them fr om damage or loss of dat a. SAMSUNG is not responsible for a ny data file damage or d ata loss.

x A USB device that requires high power (more than 0.5A) may not

be supported.

x Do not disconnect the USB device while it is loading. x The higher the resolution of the image, the longer it takes to

display on the screen.

x If a ﬁle is corrupted or the TV does not support the ﬁle type, the

“Not Supported File Format” message appears.

x The TV cann ot play MP3 files with D RM that have been

downloaded from a for-pay site. Digital Rights Management (DRM) is a technology that supports the creation, distribution, and management of di gital content in an inte grated and comprehensive way, incl uding protecting the r ights and interests of content providers, p reventing illegal c opying of contents, and managing billing and settlements.

x PTP devices are not supported. x If an over-power warning message is displayed while you are

connecting or using a USB device, the device may not be recognized or may malfunction.

x If the TV has no input during the time period set in Auto

Protection Time, the Screensaver will run.

x The power-saving mode of some external hard disk drives may be

released automatically when your connect them to the TV.

x If you use a USB extension cable, the TV may not recognize the

USB device or may not be able to read the ﬁles on the device.

x If a USB device co nnected to the TV is not r ecognized, the list of

files on the device is c orrupted, or a file in th e list is not played, connect the USB devi ce to a PC, format the device, a nd check the connection.

x If a ﬁle you deleted from the PC is still found when you run Media

Play, use the “Empty the Recycle Bin” function on the PC to permanently delete the ﬁle.

x Photos only supports the sequential jpeg format. x The Videos option does not support the scene search and

thumbnail functions.

x If the number of ﬁles and folders saved on a USB storage device is

over approximately 4000, the ﬁles and folders may not appear and some folders may not open.

x The maximum displayed number of ﬁles, including sub folders, in

one folder of USB storage device is 2000.

►

1/1

Movie 01.avi

Pause L Jump T Tools R Return

1. In the Media Play menu, press the ◄ or ► button to select Videos, and then press the ENTERE button.

2. Press the ◄/►/▲/▼ buttons to select a video in the ﬁle list.

3. Press the ENTERE button or  (Play) button.

- The file name is displayed on the top o f the screen with the

playing time.

- If video time information is unk nown, playing time and the

progress bar are not dis played.

- During video playback, you ca n search using the

◄

and

►

buttons.

✎ In this mode, you can play mov ie clips contained in a g ame,

but you cannot play the gam e itself.

y Supported Subtitle Formats

- External

Name File extension

MPEG-4 timed text .ttxt

SAMI .smi

SubRip .srt

SubViewer .sub

Micro DVD .sub or .txt

SubStation Alpha .ssa

Advanced SubStation Alpha .ass

- Internal

Name Container Format

Xsub AVI Picture Format

SubStation Alpha MKV Text Format

Advanced SubStation Alpha MKV Text Format

SubRip MKV Text Format

MPEG-4 Timed text MP4 Text Format

y Supported Video Formats

File

Extension

Container Video Codec Resolution

Frame rate(fps)

Bit

rate(Mbps)

Audio Codec

*.mp4 MP4

DivX

3.11/4.x/5.1 /6.0

1920x1080 6~30 30Mbps

MP3 /

ADPCM /

AAC

H264 1920x1080 6~30 30Mbps

AVC 1920x1080 6~30 30Mbps

MJPEG 640x480 6~30 10Mbps

*.avi

*.mkv

AVI,

MKV

DivX

3.11/4.x/5.1

/6.0

1920x1080 6~30 30Mbps

MP3 /

AC3 / LPCM / ADPCM

/ DTS

Core

MPEG4 SP

/ ASP

1920x1080 6~30 30Mbps

H264 1920x1080 6~30 30Mbps

MJPEG 640x480 6~30 10Mbps

*.asf

*.wmv

ASF

DivX 3.11 / 4.x /5.1

/ 6.0

1920x1080 6~30 30Mbps

MP3 /

AC3 / LPCM / ADPCM / WMA / WMA

Pro

MPEG4 SP

/ ASP

1920x1080 6~30 30Mbps

H.264 1920x1080 6~30 30Mbps

*.ts *.trp *.tp

*.m2ts

MPEG2 1920x1080 6~30 30Mbps

AC3 / AAC / MP3 / DD+ / HE-AAC

H. 264 BP / MP / HP

1920x1080 6~30 30Mbps

*.dat *.mpg *.mpeg

*.vob

MPEG1 1920x1080 24/25/30 30Mbps

AC3 / MPEG / LPCM /

AAC

MPEG2 1920x1080 24/25/30 30Mbps

H. 264 BP / MP / HP

1920x1080 6~30 30Mbps

*.3gp 3GPP

MPEG4 SP

/ ASP

1920x1080 6~30 30Mbps

MP3

H.264 1920x1080 6~30 30Mbps

File

Extension

Container Video Codec Resolution

Frame rate(fps)

Bit

rate(Mbps)

Audio Codec

*.ﬂv *.swf

ﬂash

formats

H.264 1920x1080 6~30 30Mbps

MP3

Sorenson

H.263

1920x1080 6~30 30Mbps

Other Restrictions

y Video content will not play, or not play correctly, if there is an error

in the content or the container.

y Sound or video may not work if the contents have a standard

bit rate/ frame rate above the compatible Frame/sec listed in the Supported Video Formats table.

y If the Index Table erroneous, the Seek (Jump) function is not

supported.

y The menu may take longer to appear if the video’s bit rate

exceeds 10Mbps.

y Video content can not be played if there are many contents in

one ﬁle.

Video Decoder

Supports up to H.264, Level 4.1

H.264 FMO / ASO / RS, VC1 SP / MP / AP L4 and AVCHD are not supported.

MPEG4 SP, ASP :

– Below 1280 x 720: 60 frame max

– Above 1280 x 720: 30 frame max

H.263 is not supported.

GMC is not support.

Audio Decoder

Supports up to WMA7, 8, 9 STD, 9 PRO, 10 PRO

WMA 9 PRO and WMA 10 PRO support 5.1 channel. (LBR mode of WMA Pro is not supported)

WMA Lossless is not supported.

Music

3/15

I Love you

Jhon

Music 1

No Singer

Music 2

No Singer

Music 3

No Singer

Music 4

No Singer

Music 5

No Singer

I Love You

Jhon

1st Album Pop 2010

4.2MB

01:10 / 04:02

SUM

Pause L Jump T Tools R Return

Playlist

1. In the Media Play menu, press the ◄ or ► button to select Music, and then press the ENTERE button.

2. Press the ◄/►/▲/▼ buttons to select the desired Music in the

ﬁle list.

3. Press the ENTERE button or  (Play) button.

✎ During music playba ck, you can search using t he ◄ and

► button.

✎



(REW) and μ (FF) buttons do not fun ction during

play.

✎ Media Play only displ ays files with MP3 and PCM f ile

extension. Other fi le extensions are not dis played, even if they are saved on the same USB dev ice.

✎ If the sound is abnorma l when playing MP3 file s, adjust the

Equalizer in the Sound menu. (An over-modula ted MP3 file may cause a sound problem.)

Photos

Image1024.jpg 1024x768 2010/2/1 3/15

Pause L Previous/Next T Tools R Return

Normal

1. In the Media Play menu, press the ◄ or ► button to select Photos, then press the ENTERE button.

2. Press the ◄/►/▲/▼ buttons to select a photo in the ﬁle list.

3. Press the ENTERE button or  (Play) button.

✎ NOTE

x While a photo lis t is displayed, press th e



(Play) / ENTERE

button on the remote cont rol to start a slide sho w.

x All files in th e file list section w ill be displayed in the s lide show. x During the sl ide show, files are disp layed in order. x During the sl ide show, you can adjust the s lide show speed

using (π) (REW) or (µ) (FF) bu tton.

x You can move to other fil es using ◄ or ► button.

✎ Media Play can play Musi c files automaticall y during a Slide

Show if Background Music is set to On.

✎ You cannot change the Mode in Background Music until the

Background Music file has finished loading.

y Supported Photo Formats

Image Photo Resolution

JPEG

Base-line 15360 x 8704

Progressive 1024 x 768

Other Restrictions

yCMYK, YCCK Color space JPEG are not supported.

Playing Multiple Files

■

Playing selected video/music/photo ﬁles

1. On the File List screen, highlight a ﬁle, and then press the Yellow

button on your remote.

2. Repeat Step 1 to select multiple ﬁles.

✎ NOTE

x A

mark appears to the le ft of the selected fi les.

x To cancel a select ion, press the Yellow butto n again. x To deselect all se lected files, pres s the TOOLS button, select

Deselect All, an d then the ENTERE button.

3. Press the TOOLS button, select Play Selected Contents, and

then press the ENTERE button.

■

Playing a video/music/photo folder

1. With the folders on your USB device displayed, use the

◄/►/▲/▼ buttons to highlight a folder.

2. Press the TOOLS button, select Play Folder, and then press the

ENTERE button.

Media Play - Additional Functions

■

Videos/Music/Photos Play Option menus

When playing a ﬁle, press the TOOLS button.

Category Operation Videos Music Photos

Title

You can select another video ﬁle to play directly.

Repeat Mode

You can play movie and music ﬁles repeatedly.

c c

Picture Size

You can adjust the picture size to your preference.

Picture Mode You can adjust the picture setting.

c c

Sound Mode You can adjust the sound setting.

c c c

Subtitle Setting

You can play the video with Subtitles. This function only works if the subtitles have the same ﬁle name as the video.

Audio Format

You can select the digital audio output format.

Audio Language

You can change the audio language if the video has more than one language.

Stop Slide Show / Start Slide Show

You can start or stop a Slide Show.

Slide Show Speed

You can select the slide show speed during the slide show.

Background Music

You can set and select background music when watching a Slide Show.

Zoom

You can zoom into images in full screen mode.

Rotate

You can rotate images in full screen mode.

Information

You can see detailed information about the played ﬁle.

c c c

Settings

Using the Setup Menu

■

DivX® Video On Demand : Shows the registration code authorized for the TV. If you connect to the DivX web site and register with the 10-digit registration code, you can download the VOD activation ﬁle. Once you play it using Media Play, the registration is completed.

✎ For more information on D ivX® VOD, visit “http://vod.divx.

com”.

■

Information: Select to view information about the connected

USB device.

Other Information

Installing the Wall Mount Kit

The wall mount kit (sold separately) allows you to mount the TV on the wall.

For detailed information about installing the wall mount, see the instructions provided with the wall mount items. Contact a technician for assistance when installing the wall mount bracket. Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you elect to install the wall mount on your own.

Wall Mount Kit Speciﬁcations (VESA)

✎ The wall mount kit is not su pplied, but sold sepa rately.

Install your wall mount on a solid wall perpendicular to the ﬂoor. When attaching to other building materials, please contact your nearest dealer. If you install the TV on a ceiling or slanted wall, it may fall and result in severe personal injury.

✎ NOTE

x Standard di mensions for wall mou nt kits are shown in the ta ble

below.

x When purcha sing our wall mount ki t, a detailed install ation

manual and all par ts necessary for a ssembly are provi ded.

x Do not use screws t hat do not comply with th e VESA standard

screw specifications.

x Do not use screws t hat are longer than th e standard dimensi on

or do not comply with the V ESA standard screw sp ecifications. Screws that are too long may c ause damage to the ins ide of the TV set.

x For wall mounts t hat do not comply with th e VESA standard

screw specificat ions, the length of the sc rews may differ depending on the wall mount specifications.

x Do not fasten the s crews too firmly. This may d amage the

product or cause the pr oduct to fall, leading to p ersonal injur y. Samsung is not liable f or these kinds of acci dents.

x Samsung is not l iable for product da mage or personal in jury

when a non-VESA or non-sp ecified wall moun t is used or the consumer fails to follow the product installation instructions.

x Do not mount the T V at more than a 15 degree til t. x Always have two p eople mount the TV o n a wall.

Product Family

TV size in

inches

VESA screw hole specs (A * B) in

millimeters

Standard

Screw

Quantity

PDP-TV

43~51 400 X 400

M8 4

60~64 600 X 400

Do not install your Wall Mount Kit while your TV is turned on. It may result in personal injury due to electric shock.

Securing the TV to the Wall

Caution: Pulling, pushing, or climbing onto the TV may cause the TV to fall. In particular, ensure that your children do not hang over or destabilize the TV; doing so may cause the TV to tip over, resulting in serious injuries or death. Follow all safety precautions provided on the included Safety Flyer. For added stability, install the anti-fall device for safety purposes, as follows.

To prevent the TV from falling

✎ Since the necessar y brackets, screws, and st ring or cable are

not supplied, please purchase these separately.

1. Insert the screws into the wall brackets and ﬁrmly fasten them to the wall. Make sure the screws are ﬁrmly ﬁxed to the wall.

✎ We strongly recommend y ou drive the screws into a stud.

2. Using M8 screws, insert the screws through the TV brackets, and then fasten the screws to the top VESA screw holes on the back of the TV.

3. Connect the brackets on the TV and the brackets on the wall with a strong string or cable, and then tie the string or cable tightly to the brackets.

✎ Verify all connect ions are properly sec ured. Periodically c heck

the connections for an y sign of fatigue or failure. I f you have any doubt about the secu rity of your connecti ons, contact a professional installer.

✎ Install the TV close to th e wall so that it does not fall. ✎ Connect the string or c able so that the brackets on th e wall

are at the same height or l ower than the brackets on the T V. Untie the string or cabl e before moving the TV.

✎ To purcase a TV Holder kit, co ntact Samsung custom er care.

Troubleshooting

If the TV seems to have a problem, ﬁrst review this list of possible problems and solutions. If none of these troubleshooting tips apply, visit samsung.com, then click on Support, or call Samsung customer service at 1-800-SAMSUNG.

Problem Possible Solution

Flickering and Dimming If your Samsung Television is ﬂickering or dimming sporadically, you may need to disable some of its energy efﬁcient

features like the Eco Sensor or the Energy Saving feature. Follow the steps below with your remote to turn these features off or on.

y Energy saving : Menu → Setup → Eco Solution → Energy Saving →Select Settings

y Eco Sensor : Menu → Setup → Eco Solution → Eco Sensor →Select Settings

Component Connections / Screen Color

If you ﬁnd that the color on your Samsung television’s screen is not correct or black and white, ﬁrst run a Self Diagnosis Test on the TV to make sure there are no device issues.

y Self Diagnosis : User Menu → Support → Self Diagnosis → Picture Test

y If the test is ok, try making sure ;

y Your connections are all consistent. For example, if you’ve used the AV In jack on your TV, make sure you have

used the AV Out jack on your video source.

y Try making sure you have connected to the correct jacks. For example, if you use the Component jacks, labeled

Pb, Pr, and Y, to connect your TV and video source, make sure you have connected the blue Pb jack on the video source to the blue Pb jack on the TV, the red Pr jack on the source to the red Pr jack on the TV.

Screen Brightness If you ﬁnd that the colors on your Samsung TV are correct but just a little too dark or bright, there are some settings

you should check before calling for a repair.

y Backlight, Contrast, Brightness, Sharpness, Color, Tint and so on. Go to “Picture” in the Menu, and then try

adjusting these options.

Unwanted Powering off If your Samsung TV appears to turn off by itself, there may be an issue with either your Timer settings or your Eco

friendly No Signal Power Off feature.

First make sure the Sleep Timer is not accidentally set. The Sleep Timer lets you fall asleep with the TV still on knowing that it will turn off after a certain period of time and not waste energy.

y Sleep Timer : User Menu → Setup → Time → Sleep Timer

If the Sleep Timer is not activated, you may have engaged the No Signal Power Off or Auto Power Off feature.

y No Signal Power Off : User Menu → Setup → Eco Solution → No Signal Power

y Auto Power Off : User Menu → Setup → Eco Solution → Auto Power Off

Trouble Powering On Before you turn the TV on, ﬁnd the red light on the right or left bottom of your TV. Press the power on button

on the TV or remote and the light should blink about 5 times before the TV turns on.

If you ﬁnd that you are having trouble powering on your Samsung television, there are a number of things to check it before making a call to the service department.

y If you happen to be using the TV as a monitor and the stand-by light only blinks for a few seconds when you

press the power button, your PC is in sleep mode. To take your PC out of sleep mode, press a key on your keyboard or move the mouse. Then try turning your TV on.

If you’re sure your power cord, remote control, and PC are functioning properly, you may be having a cable issue. If you have a cable or satellite box, your TV may appear to be off because the cable or satellite box is not outputting a signal. To test the signal output of your cable or satellite box, press the guide or info button on the cable or satellite box remote control. If the screen displays the guide or info data, the problem is caused by the box.

Problem Possible Solution

Stand Assembly • If you have any trouble assembling the stand, refer to “Install the Stand” in the Start Up or Stand Intallation Guide.

Cannot ﬁnd a channel •Re-run Plug & Play or run Auto Program. (go to MENU - Channel - Auto Program)

Poor Picture First, perform the Picture Test and to see if your TV is displaying the test image properly.

Go to MENU - Support - Self Diagnosis - Picture Test If the test image is properly displayed, the poor picture may be caused by the source or signal.

The TV image does not look as good as it did in the store.

•If you have an analog cable/satellite box, upgrade to a digital set top box. Use HDMI or Component cables to deliver HD (high deﬁnition) picture quality.

•Cable/Satellite subscribers: Try HD channels from the channel line up.

•Air/Cable Antenna connection: Try HD channels after running Auto Program.

✎ Many HD channels bro adcast up scaled S D (Standard Defi nition) content. Th e picture qualit y of up

scaled SD content is l ow.

•Adjust the Cable/Set top box video output resolution to 1080i or 720p.

The picture is distorted: macroblock error, small block, dots, pixelization.

•Compression of video contents may cause picture distortion, especially on fast moving pictures such as those in sports and action movies.

•A weak signal can cause picture distortion. This is not a TV problem.

•Mobile phones used close to the TV (within 3.3ft) may cause noise in the picture on analog and digital channels.

Color is wrong or missing. •If you’re using a Component connection, make sure the component cables are connected to the correct jacks.

Incorrect or loose connections may cause color problems or a blank screen.

There is poor color or brightness. •Adjust the Picture options in the TV menu. (go to Picture Mode / Color / Brightness / Sharpness)

•Adjust the Energy Saving option in the TV menu. (go to MENU - Setup - Eco Solution - Energy Saving )

•Try resetting the picture to the default picture settings. (go to MENU - Picture - Picture Reset)

There is a dotted line on the edge of the screen.

•If the picture size is set to Screen Fit, change it to 16:9.

•Change the cable/satellite box resolution.

The picture is black and white. •If you are using an AV composite input, connect the video cable (yellow) to the Green jack of Component Input 1

on the TV.

When changing channels, the picture freezes or is distorted or delayed.

•If connected to a cable box, please try to reset it. (Reconnect the AC cord and wait until the cable box reboots. It may take up to 20 minutes)

•Set the output resolution of the cable box to 1080i or 720p.

Sound Problems Perform the Sound Test to conﬁrm that your TV audio is properly operating.

(go to MENU - Support - Self Diagnosis - Sound Test) If the audio is OK, the sound problem may be caused by the source or signal.

There is no sound or the sound is too low at maximum volume.

•Check the volume of the device (Cable/Sat Box, DVD, Blu-ray, etc.) connected to your TV.

The picture is good, but there is no sound.

•If you are using an external device, check the device’s audio output option Ex. you may need to change your cable box’s audio option to HDMI if the box is connected to your TV using an HDMI cable.

•Reboot the connected device by reconnecting the device’s power cable.

The speakers are making an inappropriate noise.

•Check the cable connections. Make sure a video cable is not connected to an audio input.

•For Antenna or Cable connections, check the signal information. A weak signal may cause sound distortion.

•Perform the Sound Test as explained above.

No Picture, No Video

The TV will not turn on. • Make sure the AC power cord is securely plugged into the wall outlet and the TV.

•Make sure the wall outlet is working.

•Try pressing the POWER button on the TV to make sure the problem is not the remote.

If the TV turns on, refer to ‘Remote control does not work’ below.

The TV turns off automatically. •Ensure the Sleep Timer is set to Off in the Time menu.

•If your PC is connected to the TV, check your PC power settings.

•Make sure the AC power cord is plugged securely into the wall outlet and the TV.

•When you are watching TV connected to an antenna or cable connection, the TV will turn off after 10 - 15 minutes

if there is no signal.

There is no picture/video. • Check the cable connections. (Remove and reconnect all cables connected to the TV and external devices).

•Set your external device’s (Cable/Sat Box, DVD, Blu-ray etc) video outputs to match the connections to the TV input. For example, if an external device’s output is HDMI, it should be connected to an HDMI input on the TV.

•Make sure your connected devices are powered on.

•Be sure to select the correct input source by pressing the SOURCE button on the remote control.

•Reboot the connected device by reconnecting the device’s power cable.

RF (Cable/Antenna) Connection

The TV is not receiving all channels. • Make sure the coaxial cable is connected securely.

•Run Auto Program to add available channels to the channel list.

go to MENU - Channel - Auto program then select Auto and make sure the correct Cable TV signal type is set in the menu. There are 3 options. (STD, HRC and IRC)

•Verify the antenna is positioned correctly.

Problem Possible Solution

No Caption on digital channels. •Check the Caption Setup menu. Try changing Caption Mode Service 1 to CC1.

•Some channels may not have caption data.

The picture is distorted: macroblock, error, small block, dots, pixelization.

•Compression of video contents may cause picture distortion, especially on fast moving pictures such as those in sports and action movies.

•A weak signal can cause picture distortion. This is not a TV problem.

Others

Purple/green rolling horizontal bars and buzzing noise from the TV speakers with Component cable connection.

•Remove the left and right audio connections from the set-top-box. If the buzzing stops, this indicates that the settop-box has a grounding issue. Replace the Component video cables with an HDMI connection.

Plasma TV is making humming noise. •Plasma TVs typically make a soft humming sound. This is normal. It’s caused by the electrical charges that are

used to create the images on the screen.

•If the humming sound is loud, you may have set the brightness on the TV too high. Try setting the brightness lower.

•You can also have loud humming if the back of your Plasma TV is too close to a wall or other hard surface. Move the TV away from the wall. Also, try rerouting your connection cables.

•An improperly installed of wall mount can also create excessive noise.

The picture will not display in full screen. • HD channels will have black bars on either side of the screen when displaying up scaled SD (4:3) contents.

•Black bars on the top and bottom appear when movies that have aspect ratios different from your TV play on the TV.

•Adjust the picture size option on your external device or change the TV to full screen.

Image Retention (Burn In) Issue. • To minimize the possibility of screen burn, this unit is equipped with Pixel Shift screen burn reduction technology.

Pixel Shift lets you set the picture so it moves slightly up and down (Vertical Line) and side to side (Horizontal Dot). The regular, slight movement of the picture reduces screen burn in.

The remote control does not work. • Replace the remote control's batteries. Make sure you insert them with the polarity (+/–) correct .

•Clean the transmission window located on the top of the remote control.

•Try pointing the remote directly at the TV from 5~6 feet away.

The cable/set top box remote control does not turn the TV on or off, or adjust the volume.

•Program the Cable/Set top box remote control to operate the TV. Refer to the Cable/Set top box user manual for the SAMSUNG TV code.

A “Mode Not Supported” message appears.

•Check the supported resolution of the TV and adjust the external device’s output resolution accordingly. Refer to resolution settings in this manual.

Caption on the TV menu is greyed out. •You cannot select Caption in the TV menu when watching content from a device connected via HDMI or

Component.

•Caption must be activated on the external device.

There is a plastic smell from the TV. • This smell is normal and will dissipate in a few days.

TV Signal Strength is unavailable in the Self Diagnosis Test menu.

•This function is only available for digital channels received through an Antenna / RF/Coax connection.

TV is tilted to the right or left side. • Remove the stand base from the TV and reassemble it.

The Channel menu is grey out (unavailable).

•The Channel menu is only available when you select the TV source.

Your settings are lost after 30 minutes or every time the TV is turned off.

•If TV is in the Store Demo mode, it will reset audio and picture settings every 30 minutes. Please change from Store Demo mode to Home Use mode using the Plug & Play procedure. Press the SOURCE button to select TV mode, go to MENU → Setup → Plug & Play → ENTERE.

You have intermittent loss of audio or video.

•Check the cable connections and reconnect them.

•Loss of audio or video can be caused by using overly rigid or thick cables. Make sure the cables are ﬂexible

enough for long term use. If mounting the TV to the wall, we recommend using cables with 90 degree connectors.

You see small particles when you look closely at the edge of the frame of the TV.

•This is part of the product’s design and is not a defect.

POP (TV’s internal banner ad) appears on the screen.

•Select Home Use under Plug & Play mode. For details, refer to Plug & Play (Initial Setup).

✎ For detailed trouble shooting information, watch the troubleshooting videos at www.samsung.com/spsn ✎ Some functions and pi ctures shown in this man ual are available on spe cific models only. ✎ You can keep your TV in optimum c ondition by upgrading i t with the latest firmwar e from the Samsung web site (sa msung.com

→ Support → Downloads). To upgrade, downloa d the firmware to your compu ter, copy the firmware file to a USB me mory stick, insert the USB memo ry stick into the TV's USB sl ot, and then select Supp ort > Software Upgr ade in the TV's menu.

Storage and Maintenance

✎ If a sticker was attache d to the TV screen, some deb ris can remain after yo u remove the sticker. Please cle an it before watching

the T V.

✎ The exterior and scre en of the product can get sc ratched during clea ning. Be sure to wipe the exter ior and screen caref ully using

the cloth provided or a sof t cloth to prevent scratches.

Do not spray water directly onto the product. Any liquid that goes into the product may cause a failure, ﬁre, or electric shock.

Clean the product with a soft cloth dampened with in a small amount of water. Do not use a ﬂammable liquid (e.g. benzene, thinners) or a cleaning agent.

License

TheaterSound, SRS and the symbol are trademarks of SRS Labs, Inc.

TheaterSound technology is incorporated under licence from SRS Labs, Inc.

SRS TheaterSound™ provides the most immersive surround sound experience from the TVs built-in speakers, while maintaining steady volume and delivering rich bass and clear dialog.

DivX Certiﬁed® to play DivX® video up to HD 1080p, including premium content.

ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi Corporation. This is an ofﬁcial DivX Certiﬁed® device that plays DivX video. Visit divx. com for more information and software tools to convert your ﬁles into DivX videos. ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certiﬁed® device must be registered in order to play purchased DivX Video-onDemand (VOD) movies. To obtain your registration code, locate the DivX VOD section in your device setup menu. Go to vod. divx. com for more information on how to complete your registration. Covered by one or more of the following U.S. patents : 7,295,673; 7,460,668; 7,515,710; 7,519,274 DivX®, DivX Certiﬁed® and associated logos are trademarks of Rovi Corporation or its subsidiaries and are used under license.

Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.

Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS, the Symbol, & DTS and the Symbol together are registered trademarks & DTS 2.0+Digital Out is a trademark of DTS, Inc. Product includes software. © DTS, Inc. All Rights Reserved.

The terms HDMI and HDMI High-Deﬁnition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

Open Source License Notice

Open Source used in this product can be found on the following webpage. (http://opensource.samsung.com) Open Source License Notice is written only English.

To send inquiries and requests for questions regarding open sources, contact Samsung via Email (oss.request@samsung.com).

■

This product uses some software programs which are distributed under the Independent JPEG Group.

ICU License - ICU 1.8.1 and later

Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation ﬁles (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, provided that the above copyright notice(s) and this permission notice appear in all copies of the Software and that both the above copyright notice(s) and this permission notice appear in supporting documentation.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OF THIRD PARTY RIGHTS. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR HOLDERS INCLUDED IN THIS NOTICE BE LIABLE FOR ANY CLAIM, OR ANY SPECIAL INDIRECT OR CONSEQUENTIAL DAMAGES, OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.

Except as contained in this notice, the name of a copyright holder shall not be used in advertising or otherwise to promote the sale, use or other dealings in this Software without prior written authorization of the copyright holder.

All trademarks and registered trademarks mentioned herein are the property of their respective owners.

Speciﬁcations

Environmental Considerations Operating Temperature Operating Humidity Storage Temperature Storage Humidity

50°F to 104°F (10°C to 40°C) 10% to 80%, non-condensing

-4°F to 113°F (-20°C to 45°C ) 5% to 95%, non-condensing

Model Name PN64E533

Display Resolution 1920 x 1080

Screen Size (Diagonal)

64˝ Class

(64.0˝ measured diagonally)

Sound Output 10W x 2

Dimensions (W x H x D) Body

With stand

58.6 x 34.8 x 2.2 inches

(1488.8 x 885.8 x 57.0 mm)

58.6 x 37.8 x 13.1 inches

(1488.8 x 960.2 x 335.0 mm)

Weight Without Stand With Stand

79.8 lbs (36.2 kg)

91.0 lbs (41.3 kg)

✎ Design and specifications are subject to change without prior notice. ✎ This device is a Class B d igital apparatus. ✎ For information about t he power required and mo re about power consumpti on, refer to the label attac hed to the product. ✎ Typical power consumption is measured according to Energy Star Program requirements for televisions. ✎ Dispose unwanted ele ctronics through an app roved recycler. To find the nearest re cycling location, go to our w ebsite: www.

samsung.com/recyclingdirect or call, (877) 278-0799.

■

JACK PANEL DETAIL / REAR VIEW

(Unit:

inches

)

Model name

1 2 3 4 5 6

PN64E533

21.4 9.2 8.9 42.4 23.6 15.7

NOTE: All drawings are not necessarily to scale. Some dimensions are subject to change without prior notice. Refer to the dimensions prior to performing installation of your TV. Not responsible for typographical or printed errors.

9$

- 10 -- 9 -

- 14-- 13 -

- 11 -

- 15 -

- 12 -

- 16 -

[PE533-ZA]BN68-04647A-ENG.indd 2 2012-08-07 �� 2:01:35

Samsung PN64E533D2F, PN64E533 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual