Samsung MWR-WH02 User Manual
Wired Remote Control
MWR-WH02
DB98-33323A(1)
IFSE P G
Ne Po Hu
ARD
Air Conditioner
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
MWR-WH02_IB_E_33323-1.indd 21 2011-01-10 오후 1:13:51
E-2
Safety Precautions
Do not attempt to install or repair this wired remote
controller by yourself.
This remote controller contains no user-serviceable parts.
Always consult authorized service personnel for repairs.
When moving, consult authorized service personnel for
disconnection and installation of the remote controller.
Ensure that the wall is strong enough to support the
weight of the remote controller.
Must install the remote controller with rated power
supply.
In the event of a malfunction (burning smell, etc.),
immediately stop operation, turn off the electrical
breaker, and consult authorized service personnel.
WARNING
CAUTION
Do not use inflammable gases near the remote
controller.
Do not spill water into the wired remote controller.
Do not operate the remote controller with wet hands.
Do not install the remote controller in a location where
it will come into contact with the combustible gases,
machine oil, sulphide gas, etc.
Do not press buttons with a pointed thing.
Do not pull or bend the wired remote controller cable
excessively.
Do not use this wired remote controller for other
purpose.
Do not spray an insecticide or other combustible things
on the wired remote controller.
Do not clean the wired remote controller with benzene,
solvents or other chemicals.
Do not give a shock to the wired remote controller or
disassemble it by yourself.
• Before using the wired remote controller, read carefully these instructions.
• After reading the instructions, keep this user's manual in a handy and safe place.
If a user is changed, you must hand over the manuals.
• Never attempt to install the air conditioning system or to move the wired remote
controller by yourself.
MWR-WH02_IB_E_33323-1.indd 2 2011-01-10 오후 1:13:27
E-3
ENGLISH
Contents
Wired remote controller
.........................................................
4
GettinG Started
...........................................................................
5
SelectinG the automatic operatinG mode
..........................
6
SelectinG the coolinG mode
....................................................
7
SelectinG the dry mode
............................................................
8
SelectinG the Fan mode
.............................................................
9
SelectinG the heatinG mode
....................................................
10
SelectinG the Quiet mode
.........................................................
11
SelectinG the Sleep mode
..........................................................
12
adjuStinG the air SWinG direction
........................................
13
checkinG the room temperature
............................................
14
lockinG the Wired remote controller
......................................
14
SettinG the on timer
...................................................................
15
SettinG the oFF timer
.................................................................
16
SettinG the auto Stop Function
.............................................
17
SettinG the temperature limitS
................................................
18
lockinG the partS oF the Wired remote controller
.........
19
MWR-WH02_IB_E_33323-1.indd 3 2011-01-10 오후 1:13:27
E-4
Wired remote controller
The wired remote controller is installed on the wall.
Note DIP switch setting is recognized during the initialization. If any changes are
mode to the DIP switch setting after the initialization, you have to initialize
the system by pressing and or reset the power.
Press the button after cleaning the air filter. sign will be off.
The remote controller will display the filter sign to alert the user to clean the
filter and turn off the display when the
button are pressed.
will be displayed if you press the button of the function that the
indoor unit does not support.
If the indoor unit does not support Set temperature display,
Set temperature is not displayed on remote controller.
ON/OFF timer/
Error Status display
Operation mode
display
Fan speed/
Air swing display
Special function
display
ON/OFF time setup
Swing button
Room temperature
check button
Filter Reset button
Temperature
display
Operation ON/OFF button
Temperature setting
button
Fan speed setting
button
Mode selection
MWR-WH02_IB_E_33323-1.indd 4 2011-01-10 오후 1:13:28
E-5
ENGLISH
Getting Started
You have just purchased a wired remote controller and it has been installed
by your installation specialist.
Your User’s Manual contain much valuable information on using
your wired remote controller. Please take the time to read them as they will
help you take full advantage of the unit’s features.
In the manual, you will find a series of step-by-step procedures for each
function available.
The illustrations in the step-by-step procedures use 3 different symbols:
PRESS PUSH HOLD DOWN
MWR-WH02_IB_E_33323-1.indd 5 2011-01-10 오후 1:13:28
E-6
The room temperature and the fan speed are controlled
automatically in the auto mode.
1
Press the (ON/OFF) button to turn on the indoor unit.
- Do not press the (ON/OFF) button if the remote
controller is on.
Result: The air conditioner will be turned on with the
most recently used mode.
The air conditioner has a built-in protection
mechanism to prevent the unit from being damaged
when it is started immediately after being:
Plugged in
Stopped
The air conditioner will start up after 3 minutes.
2
To select the AUTO mode, press the button until Auto is
displayed on the remote controller.
Result: The air conditioner will operate in auto mode.
The auto fan speed will be selected
automatically in auto mode.
You cannot control the fan speed.
3
To adjust the temperature, press the buttons.
The temperature can be set between 18°C(65°F) and
30°C(86°F).
Result: The temperature will be adjusted by 1°C(1°F)
when the buttons are pressed.
4
To adjust the air swing direction, refer to page 13.
Note Fan speed in auto mode
When the room temperature is high, cool and strong
air will come out. After the room is cooled, mild air will
come out.
Selecting the Automatic Operating Mode
MWR-WH02_IB_E_33323-1.indd 6 2011-01-10 오후 1:13:30
Loading...