Samsung DynaFlat TX R2765, DynaFlat TX R3265, TX-R3064W, TX-R2664W, TX-R3065W Owner's Instructions Manual
...
Owner’s
Instructions
COLOR TELEVISION
TX-R2764/TX-R3064W
TX-R3264/TX-R2765
TX-R3065W/TX-R3265
TX-R2664W
2
Important Warranty Information
Regarding Television Format
Viewing
Standard screen format televisions (4:3, the aspect ratio of the screen width to height) are primarily designed to view standard format full-motion video. The images displayed on them
should primarily be in the standard 4:3 ratio format and constantly moving. Displaying stationary graphics and images on screen, such as the dark top and bottom letterbox bars (wide
screen pictures), should be limited to no more than 15% of the total television viewing per
week.
Wide screen format televisions (16:9, the aspect ratio of the screen width to height) are primarily designed to view wide screen format full-motion video. The images displayed on them
should primarily be in the wide screen 16:9 ratio format, or expanded to fill the screen if your
model offers this feature, and constantly moving. Displaying stationary graphics and images on
screen, such as the dark side-bars on non-expanded standard format television video and programming, should be limited to no more than 15% of the total television viewing per week.
Additionally, viewing other stationary images and text such as stock market reports, video
game displays, station logos, web sites or computer graphics and patterns, should be limited as
described above for all televisions. Displaying any stationary images that exceed the above guide-
lines can cause uneven aging of picture tubes (CRTs) that leave subtle, but permanent burned-in ghost
images in the television picture. To avoid this, vary the programming and images, and primarily display full screen moving images, not stationary patterns or dark bars. On television models that offer
picture sizing features, use these controls to view the different formats as a full screen picture.
Be careful in the selection and duration of television formats used for viewing. Uneven CRT
aging as a result of format selection and use, as well as other burned-in images, is not covered
by your Samsung limited warranty.
CONTENTS
3
Chapter 1: Your New TV . . . . . . . . . . . . . . . . 5
List of Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Familiarizing Yourself with The TV. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Front Panel Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Side Panel Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Rear Panel Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Remote Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Chapter 2: Installation. . . . . . . . . . . . . . . . . 11
Connecting VHF and UHF Antennas . . . . . . . . . . . . . . . . . . . . . . . . . 11
Antennas with 300-ohm Flat Twin Leads . . . . . . . . . . . . . . . 11
Antennas with 75-ohm Round Leads . . . . . . . . . . . . . . . . . . 12
Separate VHF and UHF Antennas. . . . . . . . . . . . . . . . . . . . . 12
Connecting Cable TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Cable without a Cable Box . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Connecting to a Cable Box that Descrambles All Channels . . 13
Connecting to a Cable Box that Descrambles Some Channels13
Connecting a VCR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Connecting an S-VHS VCR. . . . . . . . . . . . . . . . . . . . . . . . . . 16
Connecting a Second VCR to Record from the TV. . . . . . . . . 17
Connecting a DVD Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Connecting a Digital TV Set-Top Box (480p/1080i). . . . . . . . . . . . . . . 18
Connecting a Camcorder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Installing Batteries in the Remote Control. . . . . . . . . . . . . . . . . . . . . . 21
Chapter 3: Operation . . . . . . . . . . . . . . . . . . 22
Turning the TV On and Off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Plug & Play Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Viewing the Menus and On-Screen Displays. . . . . . . . . . . . . . . . . . . . 24
Viewing the Menus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Viewing the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Selecting a Menu Language. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Memorizing the Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Selecting the Video Signal-source . . . . . . . . . . . . . . . . . . . . . 26
Storing Channels in Memory (Automatic Method) . . . . . . . . 27
Adding and Erasing Channels (Manual Method). . . . . . . . . . 28
Changing Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Using the Channel Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Directly Accessing Channels . . . . . . . . . . . . . . . . . . . . . . . . . 29
Using the PRE-CH Button to select the Previous Channel. . . 29
Labeling the Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Setting the Clock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Customizing the Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Using Automatic Picture Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Using the Mute Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
CONTENTS
4
Chapter 3: Operation (Cont.) . . . . . . . . . . . . 37
Customizing the Sound. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Using Automatic Sound Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Viewing an External Signal Source . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Setting the Signal Source. . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Assigning Names to External input mode . . . . . . . . . . . . . . . 40
Chapter 4: Special Features. . . . . . . . . . . . . 41
Fine Tuning Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Changing the Color Tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Changing the Screen Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Digital Noise Reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Using the R.Surf Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Freezing the Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Choosing a Multi-Channel Sound (MTS) Soundtrack . . . . . . . . . . . . . 47
Adjusting the Volume Automatically. . . . . . . . . . . . . . . . . . . . . . . . . . 48
Setting the Surround. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Setting the Turbo Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Setting the On/Off Timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Setting the Sleep Timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Setting the Preferred Volume Level and Channel. . . . . . . . . . . . . . . . . 53
Viewing Closed Captions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Setting The On/Off Melody. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Using the V-Chip. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Customizing Your Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Chapter 5: Troubleshooting. . . . . . . . . . . . . 65
Identifying Problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Cleaning and Maintaining Your TV . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Using Your TV in Another Country. . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
YOUR NEW TV
5
Chapter One
YOUR NEW TV
List of Features
Your TV was designed with the latest technology. This TV is a high-performance unit that
includes the following special features:
• Full Flat Screen
• Automatic timer to turn the TV on and off
• Adjustable picture and sound settings that can be stored in the TV’s memory
• Automatic channel tuning for up to 181 channels
• A special filter to reduce or eliminate reception problems
• A built-in multi-channel sound decoder for stereo and bilingual listening
• Built-in, dual channel speakers
• A special sleep timer
• V-Chip function
Accessories
Once you have unpacked your TV, check to make sure that you have all the parts shown
here. If any piece is missing or broken, call your dealer.
Remote Control(AA59-00322B)/
AAA Batteries(4301-000121)
Owner’s Instructions
/
Safety Guide Manual
Warranty Card; 2EA/
Registration Card
YOUR NEW TV
6
Familiarizing Yourself with The TV
Front Panel Buttons
The buttons on the front panel control your TV’s basic features, including the on-screen
menu. To use the more advanced features, you must use the remote control.
˛
TV/VIDEO, SOURCE
Press to change between viewing TV programs
and signals from other components.
«
MENU
Press to see an on-screen menu of your TV's
features.
VOL – and +
Press to increase or decrease the volume.
Also used to select items on the on-screen
menu.
‹
CH and CH
Press to change channels. Also press to select
various items on the on-screen menu.
Remote Control Sensor
Aim the remote control towards this spot on the
TV.
fl
TIMER indicator
When the TV is turned on, the TIMER indicator
blinks five times. This indicator illuminates when
the TIMER mode is set to the “On” position after
setting the clock and either the On timer or Off
timer, with the remote control. Even if the power
is turned off, this indicator stays lit. (Clock must
be set before using this function.)
‚
POWER
Press to turn the TV on and off.
SOURCE
TX-R2765 / TX-R3065W / TX-R3265
TX-R2764 / TX-R3064W / TX-R3264 / TX-R2664W
YOUR NEW TV
7
Side Panel Jacks
You can use the side panel jacks to connect an A/V component that is used only occasionally, such as a camcorder or video game. (For information on connecting equipment,
see page 20.)
˛
AUDIO INPUT jacks
Used to connect the audio signals from a camcorder or video game.
«
VIDEO INPUT jack
Used to connect a video signal from a camcorder
or video game.
SUPER VIDEO INPUT jack
S-Video signal from an S-VHS VCR or DVD
player.
Note: In S-Video mode, Audio Output depends
what kind of audio input source is connected to
the side audio input jacks (AV1).
TX-R3064W/TX-R3264
TX-R2764/TX-R2664W
S-VIDEO
AV IN1
TX-R2765/TX-R3065W
TX-R3265
YOUR NEW TV
8
ANT IN
Rear Panel Jacks
Use the rear panel jacks to connect an A/V component that will be connected
continuously, such as a VCR or a DVD player.
Because there are three sets of input jacks, you can connect three different A/V
components (i.e., a VCR and a DVD, 2 VCRs, etc.)
For more information on connecting equipment, see pages 11 – 19.
˛
AUDIO-VIDEO MONITOR
OUTPUT jacks
These audio-video signals are identical to A/V
signals being displayed on the big screen.
(Typically used as the input signals for a recording
VCR.)
« ,fl
VIDEO/AUDIO INPUT jacks
Video and Audio signals from VCRs, DVD players
and similar devices.
Note: The common jack of component 1 and AV2,
component 2 and AV3 input jacks are exclusive
relation with each other.
SUPER VIDEO INPUT jack
S-Video signal from an S-VHS VCR or DVD
player.
Note: In S-Video mode, Audio Output depends
what kind of audio input source is connected to
the side audio input jacks (AV1).
‹
VHF/UHF
Connect to an antenna or to a cable TV system.
COMPONENT 1, 2 INPUT
jacks (480i/480p/1080i)
Connect to the audio and component output jacks
of a DVD player or Set-Top Box.
TX-R3064W/TX-R3264
TX-R2764/TX-R2664W
TX-R2765/TX-R3065W
TX-R3265
YOUR NEW TV
9
Remote Control
You can use the remote control up to about 23 feet from the TV. When using the remote,
always point it directly at the TV.
You can also use your remote control to operate your Set-Top Box, VCR, DVD and cable
box. See page 63 for details.
˛
POWER
Turns the TV on and off.
«
S.MODE
Adjust the TV sound by selecting
one of the preset factory settings
(or select your personal, customized sound settings).
P.MODE
Adjust the TV picture by selecting
one of the preset factory settings
(or select your personal, customized picture settings).
‹
Number buttons
Press to select channels directly
on the TV.
+100
Press to select channels over 100.
For example, to select
channel 121, press “+100,” then
press “2” and “1.”
VOL -, VOL +
Press to increase or decrease the
volume.
fl
MUTE
Press to temporarily cut off
the sound.
‚
SLEEP
Press to select a preset time interval for automatic shutoff.
MENU
Displays the main on-screen
menu.
P.SIZE
Press to change the screen size.
R.SURF
Press the R.SURF button to automatically return to a preferred
channel after a user-preset time
delay.
MODE
Selects a target device to be controlled by the Samsung remote
control (i.e., TV, Set Top Box, VCR,
Cable box, or DVD).
PRE-CH
Tunes to the previous channel.
æ
TV/VIDEO
Press to display all of the available
video sources (i.e., Antenna/Cable,
VCR).
CH and CH
(Channel Up/Down)
Press CH or CH to change
channels.
fi
INFO
Press to see the time, channel,
etc., on-screen.
ı
EXIT
Press to exit the menu.
Up,Down,Left,
Right (▲,▼,ˇ ,ˆ )/
ENTER
Press to select highlight up, down,
left, or right. While using the onscreen menus, press ENTER to
activate (or change) a particular
item.
ł
TURBO
Press to turn the TURBO sound On
or Off.
ø
MTS (Multichannel
Television Stereo)
Press to choose stereo, mono or
Separate Audio Program (SAP
broadcast).
YOUR NEW TV
10
Remote Control
TV/COMPONENT
Press to switch the TV, COMPONENT1 or 2 mode.
VCR(DVD, DVR
or STB) Controls
REW (Rewind)
Press to rewind a tape in your
VCR(DVD, DVR or STB).
STOP
Press this button to stop a tape
during play, record, rewind or
fast forward. If the button is
pressed during Full-Automatic
play, the function will be cancelled.
PLAY/PAUSE
Press the PLAY/PAUSE button to
play back prerecorded tapes or
pause the tape.
FF
Press to fast forward the tape in
your VCR(DVD, DVR or STB).
SET
Use this button when you are
setting up your remote control to
operate your Set Top Box, VCR,
Cable box or DVD.
STILL
Press to stop the action during a
particular scene. Press again to
resume normal video.
Note: The still function doesn’t
operate in Component 1 or 2 mode.
–
RESET
If your remote control is not functioning properly, take out the batteries and press the reset button
for about 2~3 seconds. Re-insert
the batteries and try using the
remote control again.
INSTALLATION
11
Chapter Two
INSTALLATION
Connecting VHF and UHF Antennas
If your antenna has a set of leads that
look like this, see “Antennas with
300-ohm Flat Twin Leads” below.
If your antenna has one lead that looks
like this, see “Antennas with 75-ohm
Round Leads” on next page.
If you have two antennas, see “Separate
VHF and UHF Antennas” on next page.
Antennas with 300-ohm Flat Twin Leads
If you are using an off-air antenna (such as a roof antenna or “rabbit ears”) that has
300-ohm twin flat leads, follow the directions below.
1
Place the wires from the
twin leads under the
screws on the 300-75 ohm
adaptor (not supplied).
Use a screwdriver to
tighten the screws.
2
Plug the adaptor into the
VHF/UHF terminal on the
bottom of the back panel.
INSTALLATION
12
Connecting Cable TV
To connect to a cable TV system, follow the instructions below.
Cable without a Cable Box
▼
1
Plug the incoming cable
into the VHF/UHF antenna
terminal on back of the TV.
Because this TV is cable-ready,
you do not need a cable box to view
unscrambled cable channels.
2
Plug the combiner into the
VHF/UHF terminal on the
bottom of the rear panel.
Separate VHF and UHF Antennas
If you have two separate antennas for your TV (one VHF and one UHF), you must
combine the two antenna signals before connecting the antennas to the TV. This
procedure requires an optional combiner-adaptor (available at most electronics shops).
1
Connect both antenna
leads to the combiner.
Antennas with 75-ohm Round Leads
1
Plug the antenna lead into
the VHF/UHF terminal on
the bottom of the back
panel.
INSTALLATION
13
Connecting to a Cable Box that Descrambles All Channels
▼
1
Find the cable that is connected to the ANTENNA
OUT terminal on your
cable box.
This terminal might be labeled
“ANT OUT”, “VHF OUT” or simply,
“OUT”.
2
Connect the other end of
this cable to the VHF/UHF
antenna terminal on the
back of the TV.
Connecting to a Cable Box that Descrambles Some Channels
If your cable box descrambles only some channels (such as premium channels), follow the
instructions below. You will need a two-way splitter, an RF (A/B) switch, and four lengths of
coaxial cable. (These items are available at most electronics stores.)
▼
1
Find and disconnect the
cable that is connected to
the ANTENNA IN
terminal on your cable
box.
This terminal might be labeled
“ANT IN”, “VHF IN” or simply,
“IN”.
2
Connect this cable to a
two-way splitter.
3
Connect a coaxial cable
between an OUTPUT terminal on the splitter and
the IN terminal on the
cable box.
Incoming Cable
Splitter
Incoming Cable
Cable Box
Splitter
INSTALLATION
14
4
Connect a coaxial cable
between the ANTENNA
OUT terminal on the cable
box and the B–IN terminal
on the RF(A/B) switch.
5
Connect another cable
between the other OUT
terminal on the splitter
and the A–IN terminal on
the RF (A/B) switch.
6
Connect the last coaxial
cable between the OUT
terminal on the RF (A/B)
switch and the VHF/UHF
terminal on the rear of the
TV.
After you’ve made this connection, set the A/B switch to the “A” position for normal viewing. Set the A/B switch to the “B” position to view scrambled channels. (When you set the
A/B switch to “B”, you will need to tune your TV to the cable box’s output channel, which is
usually channel 3 or 4.)
Incoming
Cable
Cable Box
RF (A/B)
Switch
Splitter
Incoming
Cable
Cable Box
RF (A/B)
Switch
Splitter
Incoming
Cable
Cable Box
RF (A/B)
Switch
TV Rear
Splitter
INSTALLATION
15
ANT
IN
3
Connect a coaxial cable
between the ANTENNA
OUT terminal on the
VCR and the antenna
terminal on the TV.
AN
4
Connect a set of audio
cables between the
AUDIO OUT jacks on the
VCR and the AUDIO
jacks on the TV.
ANT IN
5
Connect a video cable
between the VIDEO OUT
jack on the VCR and the
VIDEO jack on the TV.
Follow the instructions in “Viewing an External Signal Source” to view your VCR tape.
A coaxial cable is usually included with a VCR. (If not, check your local electronics store).
Connecting a VCR
These instructions assume that you have already connected your TV to an antenna or a cable
TV system (according to the instructions on pages 11-14). Skip step 1 if you have not yet
connected to an antenna or a cable system.
1
Unplug the cable or
antenna from the back
of the TV.
2
Connect the cable or
antenna to the
ANTENNA IN terminal
on the back of the VCR.
Incoming
Cable or
Antenna
VCR Rear Panel
VCR Rear Panel
Coaxial Cable
TV Rear Panel
VCR Rear Panel
Audio Cable
TV Rear Panel
VCR Rear Panel
Video Cable
TV Rear Panel
INSTALLATION
16
ANT IN
3
Connect an S-video
cable between the
S-VIDEO OUT jack on
the VCR and the
S-VIDEO INPUT
jack on the TV.
An S-video cable is usually included with an S-VHS VCR (If not, check your local
electronics store.)
Make sure the jacks you are using are underneath the number “1.”
A
2
Connect a set of audio
cables between the
AUDIO OUT jacks on the
VCR and the 1 AUDIO
INPUT jacks on the TV.
1
To begin, follow steps
1–3 in the previous
section to connect the
antenna or cable to your
VCR and your TV.
Connecting an S-VHS VCR
Your Samsung TV can be connected to an S-Video signal from an S-VHS VCR. (This
connection delivers a better picture as compared to a standard VHS VCR.)
ANT IN
VCR Rear Panel
Coaxial Cable
TV Rear Panel
VCR Rear Panel
Audio Cable
TV Rear Panel
VCR Rear Panel
Video Cable
TV Rear Panel
INSTALLATION
17
Connecting a Second VCR to Record from the TV
Your TV can send out signals of its picture and sound to be recorded by a second VCR.
To do this, connect your second VCR as follows:
ANT IN
1
Connect a set of audio
cables between the
AUDIO OUT jacks on the
TV and the AUDIO IN
jacks on the VCR.
ANT IN
2
Connect a video cable
between the VIDEO OUT
jack on the TV and the
VIDEO IN jack on the
VCR.
Refer to your VCR’s instructions for more information about how to record using this kind
of connection.
(The VCR input jacks might be either on the front or on back of the VCR.)
Connecting a DVD Player (480i)
The rear panel jacks on your TV make it easy to connect a DVD player to your TV.
1
Connect a set of audio
cables between the
COMPONENT INPUT 1 (L,
R) or COMPONENT
INPUT 2 (L, R) jacks on
the TV and the AUDIO
OUT jacks on the DVD
player.
ANT IN
2
Connect a video cable
between the COMPONENT INPUT 1 (Y, PB,
PR) or COMPONENT
INPUT 2 (Y, PB, PR) jacks
on the TV and the COMPONENT VIDEO OUT (Y,
PB, PR) jacks on the DVD
player.
VCR Input Panel
Audio Cable
TV Rear Panel
VCR Input Panel
Video Cable
TV Rear Panel
DVD Player Rear Panel
TV Rear Panel
Audio Cable
DVD Player Rear Panel
TV Rear Panel
Video Cable
Note: For an explanation of Component video, see your DVD player's owner's manual.
INSTALLATION
18
Connecting a Digital TV Set-Top Box
(480p/1080i)
Connecting to Y,PB,P
R
Connect the Y, PB, and PRvideo outputs of the set-top box to their corresponding inputs
on the TV. Next, connect the Left and Right audio from the set-top box to the corresponding L and R terminals on the TV. (The connections for a typical set-top box are
shown below.)
ANT IN
1
Connect a coaxial cable
between the ANTENNA
OUT terminal on the Set
Top Box and the antenna
terminal on the TV.
Set Top Box Rear Panel
Coaxial Cable
TV Rear Panel
ANT IN
2
Connect a set of audio
cables between the COMPONENT INPUT 2 (L, R) or
COMPONENT INPUT 1 (L,
R) jacks on the TV and the
AUDIO OUT jacks on the
Set Top Box.
Set Top Box Rear Panel
Audio Cable
TV Rear Panel
INSTALLATION
19
Note: For detailed information, refer to the Set Top Box instruction manual.
ANT IN
3
Connect a video cable
between the COMPONENT INPUT 2 (Y, PB, PR)
or COMPONENT INPUT 1
(Y, PB, PR) jacks on the TV
and the VIDEO OUT (Y, PB,
PR) jacks on the Set Top
Box.
Video Cable
Set Top Box Rear Panel
TV Rear Panel
INSTALLATION
20
2
Connect an audio cable
between the AUDIO
OUTPUT jack on the
camcorder and the
AUDIO terminals on the
side of the TV.
3
Connect a video cable
between the VIDEO
OUTPUT jack on the
camcorder and the
VIDEO terminal on the
side of the TV.
1
Locate the A/V output
jacks on the camcorder.
They are usually found
on the side or back of
the camcorder.
Connecting a Camcorder
The side panel jacks on your TV make it easy to connect a camcorder to your TV. They allow
you to view the camcorder tapes without using a VCR. (Also see “Viewing an External Signal
Source” on page 39).
The audio-video cables shown here are usually included with a Camcorder. (If not, check
your local electronics store.) If your camcorder is stereo, you need to connect a set of two
cables.
Note: This figure shows the Standard connector-jack panel. The actual configuration for
your TV may be different.
Camcorder
Output Jacks
Camcorder
Output Jacks
Audio Cable
Video Cable
Y-Connector
TV Side Panel
Camcorder
Output Jacks
TV Side Panel
INSTALLATION
21
▼
3
Replace the cover.
Remove the batteries and store
them in a cool, dry place if you won’t
be using the remote control for a
long time.
The remote control can be used up
to about 23 feet from the TV.
(Assuming typical TV usage, the
batteries last for about one year.)
▼
2
Install two AAA size
batteries.
Make sure to match the “+” and
“
–” ends of the batteries with the
diagram inside the compartment.
Installing Batteries in the Remote Control
1
Slide the cover out completely.
Loading...