Samsung CN15MSAPN, CN15MSAAN, CN15MSAPSP Disassemble

3-1-1 Removing the Stand

1. Remove 4 screws in the hinge area.

2. Pry it off the back of the monitor.

3. Disconnect Power Cord and Signal Cable.

3-1-2 Main Body Disassembly

1. Remove the 4 screws on the four corner of the
Rear Cover.

2. Remove Rear Cover from the Front Cover.

3. Remove 11 screws on the Shield and remove
the shield.

4. Disconnect Inverter wire, Function PCB wire
and Interface wire.
Remove 4 screws on the Main PCB and
remove 2 screws on the D sub shield.

5. Remove the Main PCB Assembly.

6. Remove 6 screws on the Inverter PCB
Assembly and then remove it

7. Remove 6 screws on the Rear Panel Bracket.

8. Remove the Bracket Assembly from the Front
Cover.

9. Remove 3 screws on the Function PCB from
locking area of Function knob and remove
Function PCB.

10. Remove 4 screws on the Shield of Panel.

11. Remove the Shield.

12. Remove Rear Bracket from Panel.

13. Remove 2 screws between Panel Rear and
Inverter PCB.

14. Remove the Interface wire on the Rear Side of
Panel.

3-1-3 Standard Stand Disassembly

1. Remove 5 screws from the Stand Rear

2. Remove 4 screws from the Stand Bottom.

3. Remove Stand Front from the Stand assembly.

4. Remove 2 screws from the Stand assembly.

5. Remove the Stand Rear from the Stand
assembly.

6. Remove 5 screws on the Vesa Brkt from the
Stand assembly.

7. Remove cover hinge from the Stand assembly.

8. Remove Stand Base from the Stand assembly.

3-1-4 Pivot Multi-media Stand Disassembly

(option)

1. Stand the stand assembly with the base close
to you.

2. Remove the 4 screws on the back cover of the
stand and remove it.

3. Stand the stand assembly upside down.

4. Remove the 4 screws.

5. Disconnect CN805, CN806, CN807, CN808,
CN809, CN812 and F1.

6. Remove the Back Cover of the Stand Front
assembly.

7. Remove 4 screws on the external adaptor and
remove the adaptor.

8. Remove 2 screws between hinge and Stand
Body.

9. Remove the hinge

10. Remove 2 screws on Audio main PCB and
remove it

11. Remove 2 screws on the Audio Function PCB
and remove it.

3-1-5 Angle Pivot Stand Disassembly (option)

1. Remove the cap pivot from the stand
assembly.

2. Remove the 4 screws on the hinge assembly.

3. Remove the 4 screws on the Stand Rear

SyncMaster 570B TFT / 580B TFT 3-1

3 Disassembly and Reassembly

This section of the service manual describes the disassembly and reassembly procedures for the
Sync Master 570B TFT / 580B TFT monitors.

WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling

these components.

3-1 Disassembly

Cautions:1. Disconnect the monitor from the power source before disassembly.

2. Follow these directions carefully; never use metal instruments to pry apart the cabinet.

4. Remove the Stand Rear from the Stand
assembly.

5. Remove the Stand Front from the Stand
assembly.

6. Remove the Neck Rear from the Stand
assembly.

7. Remove the 4 Rubbers on the four corner of
the Stand Bottom and the 4 screws on the four
corner of the Stand Bottom.

8. Remove the 5 stopper hings from the Bracket
Bottom.

9. Remove the Stand Base from the Stand
Assembly.

3-1-6 Wire frame stand Disassembly (option)

1. Carefully pull the cover hinge.

2. Remove the cover vesa from the Stand
assembly.

3. Remove 4 screws on the assembly Bracket
assembly.

3 Disassembly and Reassembly

3-2 SyncMaster 570B TFT / 580B TFT

1. After confirm there is nothing
on the disk
Turn the LCD module over
and put it on a flat desk set to
the ground.

3-2 Replacement Order of Lamp Assemblies (CN15MSS/CN15MOS : Samsung Panel)

2. Push down the stopper and
slide the lamp unit.