Switch Ethernet Fast
RUB TECH |
R |
|
Fast EthernetSwitch |
||
Networking & Communications |
L2 Managed Switch
ES-2310C
ES-2310C:
8-Port L2 Managed Fast Ethernet Switch with 2 SFP Gigabit Dual Media
Key Features
Standard compliance
---IEEE 802.3 10Base-T
---IEEE 802.3u 100Base-TX
---IEEE 802.3ab 1000Base-TX
---IEEE 802.3z 1000Base-X Ethernet
---IEEE 802.3x flow control capability
---ANSI/IEEE 802.3 auto-negotiation
---IEEE 802.1q VLAN
RoHS Compliance
Subscriber Interface
---8 are 10/100Mbps and 2 Gigabit Ethernet ports.
---Port 9,10 are Gigabit TP/SFP Fiber auto sense
---Auto-Negotiation and Auto-MDIX
---Back pressure flow control for half duplex.
---IEEE 802.3x compliant for full duplex
---Connector: 8 RJ-45 and 2 dual media, RJ-45/SFP
Performance
Switching capacity:
---Non-blocking switch fabric supports up to 8 FE+2GbE ports
---8 K MAC addresses
---256K packet buffer and 128K control memory
VSM(Virtual Stacking Management)
---Supports 16 devices stacking
---Multiple switches can be managed via one IP address, just like software stacking
---Low cost and easily to establish network environment, not extra hardware require
---Not center on the physical location of wiring closets
VLAN
---Supports SVL/IVL configuration to meet your VLAN requirement
---Port-base VLAN
---IEEE802.1q tag-base VLAN, 4094 max, up to 256 active VLANs including static plus dynamic entry
---IEEE802.1q tag-base VLAN
Benefits
QoS with four priority queues
The QoS(Quality Of Service) feature provides four internal queues to support four different classifications of traffic. High priority packet streams experience less delay inside the switch, which supports lower latency for certain delaysensitive traffic. The ES-2310C can classify the packet as one of the four priorities according to vip port, 802.1p priority tag, DiffServ and/or IP TOS. The QoS operate at full wire speed. The actual scheduling at each egress port can be based upon a strict priority, weighted round robin or a mix of both.
Port Mirroring
This mechanism helps track network errors or abnormal packet transmission without interrupting the flow of data. Allow ingress traffic to be monitored by a single port that is defined as mirror capture port. The mirror capture port can be any 10/100 port, 10/100/1000 port. Mirroring multiple ports is possible but can create congestion at the mirror capture port.
Q-in-Q VLAN for performance & security
The VLAN feature in the switch offers the benefits of both security and performance. VLAN is used to isolate traffic between different users and thus provides better security. Limiting the broadcast traffic to within the same VLAN broadcast domain also enhances performance. Q-in-Q, the use of double VLAN tags is an efficient method for enabling Subscriber Aggregation. This is very useful in the MAN.
Isolated Group, provides protection for certain ports
The isolated group feature allows certain ports to be designated as protected. All other ports are non-isolated. Traffic between isolated group members is blocked. Traffic can only be sent from isolated group to non-isolated group.
Mac-based 802.ad LACP with automatic link fail-over
Dynamic fail-over means packets will not get assigned to any trunk member port that has failed. If one of the ports were to fail, traffic will automatically get distributed to the remaining active ports.
802.1x Access Control improves network security
802.1x features enable user authentication for each network access attempt. Port security features allow you to limit the number of MAC addresses per port in order to control the number of stations for each port. Static MAC addresses can be defined for each port to ensure only registered machines are allowed to access. By enabling both of these features, you can establish an access mechanism based on user and machine identities, as well as control the number of access stations.
802.1d Compatible & 802.1w Rapid Spanning Tree
For mission critical environments with multiple switches supporting STP, you can configure the switches with a redundant backup bridge path, so transmission and reception of packets can be guaranteed in event of any fail-over switch on the network.
2 dual media ports for flexible fiber connection
Port 9, 10 dual media ports are provided for flexible fiber connection. You can select to install optional transceiver modules in these slots for short, medium
Loading...