SuperSnap™ with AnoConnector Instruction Sheet
Parts
|
|
|
6” Rod |
|
|
|
|
97-0304-06 |
|
CableClip |
SuperSnap |
End Caps |
AnoConnector |
Ball Chains |
06-5050 |
12S300 |
06-5475 |
06-2930 |
96-0302P |
Instructions for assembly |
|
|
|
|
Step 1 |
|
|
|
|
Insert single ball of ball chain into inner |
|
|
|
|
channel of Cable Clip. The cable should |
|
|
|
|
snap into place. Fig. 1 |
|
|
|
|
Align one round end of cable clip with top |
|
|
|
|
channel of the rail and insert. Once in |
|
|
|
|
place, insert end of ball chain into channel. |
Figure 1 |
Figure 2 |
||
Then press down on the other round end of |
||||
the cable clip and slide into rail by pushing |
|
|
|
|
on the clip. Fig. 2 |
|
|
|
|
Note: Be sure to push on the cable clip in |
|
|
|
|
order to slide the ball chain into place. Do |
|
|
|
|
not pull on, or push against, the ball chain |
|
|
|
|
as this will cause it to bind in the channel. |
|
|
|
|
Note: Position CableClip about halfway |
Figure 3 |
|
|
|
down each SuperSnap. Fig. 3 |
|
|
||
Step 2 |
|
|
|
Figure 4 |
Insert AnoConnector into rail of one |
|
|
||
SuperSnap. Make sure tabs face upward. The |
|
|
|
|
side with one tab must go in first. Fig. 4 |
|
|
|
|
Step 3 |
|
|
|
|
Insert threaded rod halfway into clip rail of |
|
|
|
|
the same SuperSnap. Fig. 5 |
|
|
|
|
Step 4 |
|
|
|
|
Push the second piece of SuperSnap onto |
|
|
|
|
both AnoConnector and the threaded rod. |
|
|
|
|
Push together until |
|
Figure 5 |
|
Figure 6 |
both holders meet. Fig. 6 Repeat steps 2-4 |
|
|||
for additional SuperSnaps. |
|
|
|
Page 1 of 2 |
|
|
|
|
|
The SuperSnap™ is a trademark of Rose Displays, Ltd. Neither the |
|
|
|
|
manufacturer nor any sales agent may be held liable for injury, loss or |
|
|
||
damage resulting from the use of these products. |
|
|
|
|
Part #02INSSuperSnapAnoConnectorCCBC |
|
|
|
|
35 Congress Street, Salem, MA 01970 |
|
Tel# 1- 800 631-9707 Fax# 1-800-560-2890 |
Incept-11.13.02 |
e-mail:signware@rosedisplays.com |
SuperSnap™ with AnoConnector Instruction Sheet
Parts
|
|
|
|
6” Rod |
|
|
|
|
97-0304-06 |
|
|
CableClip |
SuperSnap |
End Caps |
AnoConnector |
Ball Chains |
|
06-5050 |
12S300 |
06-5475 |
|
06-2930 |
96-0302P |
Instructions for assembly |
|
|
|
|
|
(continued) |
|
|
|
|
|
Step 5 |
|
|
|
|
|
Snap all sections of the SuperSnap |
|
|
|
|
|
open. Fig. 7 |
|
|
|
|
|
Note: It is easier to open and close |
|
|
|
|
|
the SuperSnap by starting at one |
|
|
|
|
|
end and working your way down |
|
|
|
|
|
the holder. |
|
|
|
|
|
Step 6 |
|
Open all holders |
Figure 7 |
Figure 8 |
|
Insert graphic into one section of |
|
|
|
|
|
SuperSnap (top and bottom). Fig. 8 |
|
|
|
|
|
Step 7 |
|
|
|
|
|
To close, snap the SuperSnap shut. |
|
|
|
|
|
Fig. 9 |
|
|
|
|
|
Step 8 |
|
|
|
|
|
You should now have one graphic in |
|
|
|
|
|
place. Repeat steps 5-7 for hanging |
|
|
|
|
|
additional graphics. |
|
Insert posters |
Figure 9 |
Figure 10 |
|
Step 9 |
|
||||
|
|
|
|
|
|
Push end caps into place. Fig 10 |
|
|
|
|
|
Step 10 |
|
|
|
|
|
Suspend holders. Finished Look |
|
|
|
|
|
Important note: |
|
|
|
|
|
Please save and reuse the |
|
|
Finished Look |
||
SuperSnap, End Caps and |
|
|
|||
CableClips for future projects. |
|
|
|
|
|
|
|
|
|
|
Page 2 of 2 |
The SuperSnap™ is a trademark of Rose Displays, Ltd. Neither the |
|
|
|
|
|
manufacturer nor any sales agent may be held liable for injury, loss or |
|
|
|
||
damage resulting from the use of these products. |
|
|
|
|
|
Part #02INSSuperSnapAnoConnectorCCBC |
|
|
|
|
|
35 Congress Street, Salem, MA 01970 |
|
Tel# 1- 800 631-9707 Fax# 1-800-560-2890 |
Incept-11.13.02 |
e-mail:signware@rosedisplays.com |