Specifications
Number of Channels |
S-1608 : 16 in 8 out S-0816 : 8 in 16 out |
AD and DA Conversion |
24 bit / 96 kHz |
Frequency Response |
-2 dB / +0 dB (@ +4 dBu, 20 Hz to 20 kHz) |
Total Harmonic Distortion + Noise |
0.05 % or less (Pad: On, Input Gain: +4 dBu, 22Hz to 20 kHz) |
Dynamic Range |
110 dB |
Cross Talk |
-80 dB or less (Input Gain: +4 dBu, typ.) |
Nominal Input Level |
-65 to -10 dBu (PAD: Off), -45 to +10 dBu (PAD: On) |
|
(1 dB step, Max. +28 dBu) |
PAD |
20 dB On/Off |
Input Impedance |
14 k ohms |
Nominal Output Level |
+4 dBu, Max. +22 dBu |
Output Impedance |
600 ohms |
Recommended Load Impedance |
10 k ohms or greater |
Residual Noise Level (IHF-A, typ.) |
-80 dBu or less |
Equivalent Input Noise Level |
S-1608: -128 dB S-0816: -124dB |
Network Latency |
375 microseconds when using REAC cable only (*1) |
|
(AD > REAC > DA Latency: approx 1.2 ms) |
Connectors |
S-1608 : Analog Input x 16 (XLR type, balanced, phantom power) |
|
Analog Output x 8 (XLR type, balanced) |
|
Digital Output connector x 1 (Optical type) |
|
REAC Connector x 1 (RJ-45 EtherCon type) |
|
Remote Connector x 1 (RS-232C, DB-9 type) |
|
S-0816 : Analog Input x 8 (XLR type, balanced, phantom power) |
|
Analog Output x 16 (XLR type, balanced) |
|
Digital Output connector x 1 (Optical type) |
|
REAC Connector x 1 (RJ-45 EtherCon type) |
|
Remote Connector x 1 (RS-232C, DB-9 type) |
Indicators |
POWER Indicator x 1, REAC Indicator x 1, |
|
REMOTE Indicator x 1, MUTE ALL OUTPUTS Indicator x 1 |
Power Supply |
AC 115 V, AC 117 V, AC 220 V, AC 230 V, AC 240 V (50/60 Hz) |
Power Comsumption |
45W |
Phantom Power |
+48 V / 14 mA (each input, remote controlled) |
Dimensions |
401 (W) x 135 (D) x 177 (H) mm or |
|
15-13/16 (W) x 5-3/8 (D) x 7 (H) inches |
Weight |
5.5 kg 12 lbs 3 oz |
Operation Temperature |
0 to +40 degrees Celsius |
|
+32 to +104 degrees Fahrenheit |
Accessories |
Power Cord x 1, REAC Connector Cover x 1, Ferrite Cores x 1 |
|
Rubber Foot x 4, Rack Mount Kit x 1, Owner's Manual |
*1: When a REAC Splitter S-4000-SP or a switching hub is used in-line with REAC cables, the network latency will increase by the amount of processing delay introduced by the splitting device itself. The actual delay is dependant upon the specifications of the splitting device, though the maximum delay amount for a single splitting device should be about 200 microseconds.
*0 dBu = 0.775 Vrms
*In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice.
S-1608 Dimensions(mm) |
S-0816 Dimensions with rack mount kit (mm) |
|
135 |
135 |
|
401 |
482 |
|
177 |
101.6 |
177 |
|
465 |
|
Optional Items
S-4000R
Remote Controller
S-4000R can be connected to both S-1608 or S-0816. It provides easy remote control of gain adjustments and controls Phantom power and PAD Settings. The S-4000R can save up to 10 setups to internal memory for instant recall of the all settings.
S-4000-SP
REAC Splitter
The S-4000SP is a dual 5-port dedicated gigabit splitter for the RSS Digital Snake System that provides highest level of reliability with backup REAC ports, two power supplies and Neutrick(R) Ethercon Connectors.
SC-W100S
100 meter Cat5e Cable
Crossover cable with Neutrik(R) Ethercon connectors
S-4000 RCS
Remote Control Software
As an alternative to the S-4000R a computer can be connected to the REMOTE terminals (RS-232C) of S- 1608 or S-0816 and controlled by the S-4000 RCS Remote Control Software. This software is available as a free download for Mac or PC.
* The S-4000 RCS software is downloadable from www.rolandsystemsgroup.net
Digital Audio Transfer System
C o m p a c t , P o r t a b l e D i g i t a l S n a k e S y s t e m
S-1608
Stage Unit
S-0816
FOH Unit
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Copyright 2007 Roland Corporation. All rights reserved. |
|
|
www.rolandsystemsgroup.net |
All specification and appearances are subject to change without notice. |
|
|
||||||
May 2007 RAM-7006 KS |
|
|