Rockford Fosgate 150S, 200S, 300S, 400S, 500S User Manual

...
5 (1)

150S

 

200S

 

300S

 

Installation &

400S

Operation

500S

700S

 

 

2-Channel Amplifiers

Installation et fonctionnement

Instalación y operación

Einbau und Betrieb

Installazione e funzionamento

INTRODUCTION

Dear Customer,

Congratulations on your purchase of the world's finest brand of car audio amplifiers. At Rockford Fosgate we are fanatics about musical reproduction at its best, and we are pleased you chose our product. Through years of engineering expertise, hand craftsmanship and critical testing procedures, we have created a wide range of products that reproduce music with all the clarity and richness you deserve.

For maximum performance we recommend you have your new Rockford Fosgate product installed by an Authorized Rockford Fosgate Dealer, as we provide specialized training through Rockford Technical Training Institute (RTTI). Please read your warranty and retain your receipt and original carton for possible future use.

Great product and competent installations are only a piece of the puzzle when it comes to your system. Make sure that your installer is using 100% authentic installation accessories from Connecting Punch in your installation. Connecting Punch has everything from RCA cables and speaker wire to Power line and battery connectors. Insist on it! After all, your new system deserves nothing but the best.

To add the finishing touch to your new Rockford Fosgate image order your Rockford accessories, which include everything from T-shirts and jackets to hats and sunglasses.

To get a free brochure on Rockford Fosgate products and Rockford accessories, in the U.S. call 480-967-3565 or FAX 480-967-8132.

For all other countries, call +001-480-967-3565 or FAX +001-480-967-8132.

PRACTICE SAFE SOUND™

Continuous exposure to sound pressure levels over 100dB may cause permanent hearing loss. High powered auto sound systems may produce sound pressure levels well over 130dB. Use common sense and practice safe sound.

If, after reading your manual, you still have questions regarding this product, we recommend that you see your Rockford Fosgate dealer. If you need further assistance, you can call us direct at 1-800- 669-9899. Be sure to have your serial number, model number and date of purchase available when you call.

The serial number can be found on the outside of the box. Please record it in the space provided below as your permanent record. This will serve as verification of your factory warranty and may become useful in recovering your source unit if it is ever stolen.

Serial Number: _________________________________________

Model Number: ________________________________________

TABLE OF CONTENTS

Introduction . . . . . . . . . . . . . . . . . . . . . .

. . 2

Operation . . . . . . . . . . . . . . . . . . . . . .

11-12

Safety Instructions . . . . . . . . . . . . . . . . .

. . 3

Adjusting Gain . . . . . . . . . . . . . . .

. . . 11

Design Features . . . . . . . . . . . . . . . . . . .

. 4-5

Adjusting Crossover Frequency. . . .

. . . 11

Installation . . . . . . . . . . . . . . . . . . . . . .

5-11

Accessories. . . . . . . . . . . . . . . . . . . . . .

. . 12

Installation Considerations . . . . . . . . .

. . 5

Troubleshooting . . . . . . . . . . . . . . . . . .

. . 13

Mounting Locations. . . . . . . . . . . . . .

. . 6

Specifications . . . . . . . . . . . . . . . . . . . .

. . 14

Battery and Charging . . . . . . . . . . . . .

. . 6

Limited Warranty Information. . . . . . . .

. . 15

Wiring the System . . . . . . . . . . . . . . .

. . 6

International Instructions . . . . . . . . . . .

. . 16

Using Passive Crossovers . . . . . . . . . .

. 10

 

 

Remote Punch Bass (300S-700S Only) . 11

NOTE: Review each section for more detailed information.

2

GETTING STARTED

Welcome to Rockford Fosgate! This manual is designed to provide information for the owner, salesperson and installer. For those of you who want quick information on how to install this product, please turn to the Installation Section of this manual. Other information can be located by using the Table of Contents. We, at Rockford Fosgate, have worked very hard to make sure all the information in this manual is current. But, as we are constantly finding new ways to improve our product, this information is subject to change without notice.

SAFETY INSTRUCTIONS

This symbol with “WARNING” is intended to alert the user to the presence of important instructions. Failure to heed the instructions will result in severe injury or death.

This symbol with “CAUTION” is intended to alert the user to the presence of important instructions. Failure to heed the instructions can result in injury or unit damage.

! CAUTION: To prevent injury and damage to the unit, please read and follow the instructions in this manual. We want you to have enjoyment from this system, not a headache.

! CAUTION If you feel unsure about installing this system yourself, have it installed by a qualified Rockford Fosgate technician.

! CAUTION Before installation, disconnect the battery negative (-) terminal to prevent damage to the unit, fire and/or possible injury.

 

 

 

 

 

CONTENTS OF CARTON

Either a Model 150S, 200S, 300S, 400S,

 

1

9/64" Allen Wrench

 

500S or 700S Punch 2-Channel Amplifier

 

1

Fuse Connector (150S, 200S, 300S, 400S

 

 

 

Installation & Operation Manual

 

and 500S Only)

Mounting Hardware Kit

 

1

20

Amp Fuse (150S, 200S)

Remote Punch Bass Kit with Cord

 

1

30

Amp Fuse (300S)

1

High Level Input Harness

 

1

40

Amp Fuse (400S)

1

3/32" Allen Wrench

 

1

50

Amp Fuse (500S)

 

 

 

 

 

 

The hardware kit included with each amplifier contains the mounting hardware necessary to secure the amplifier to the vehicle and to attach the end caps to the amplifier.

NOTE: Refer to the specifications section for recommended fuse sizes for Model 700S

Visit our web site for the latest information on all Rockford products.

www.rockfordfosgate.com

3

DESIGN FEATURES

Connections -

Models 150S &

200S

Power

Connections -

Models 300S,

400S & 500S

Power

Connections -

Model 700S

Connections - Models 300S, 400S, 500S & 700S

1

6

 

 

 

 

 

 

 

 

 

8

5

 

7

 

 

9

2

 

 

 

 

 

 

 

3

 

4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10 10

1

2

3

4

1

2

3

4

5

6

7

8

7

9

6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10

10

1.LED Power Indicator – The LED illuminates when the unit is turned on.

2.REM Terminal – This spade terminal is used to remotely turn-on and turn-off the amplifier when +12V DC is applied.

3.Power Terminals – The power and ground connectors on the amplifier are gold-plated and will accommodate up to 8 AWG (10 AWG Model 200S) wire maximizing the input current capability of the amplifier.

4.Cast Aluminum Heatsink – The cast aluminum heatsink of the Punch amplifier dissipates heat generated by the amplifier's circuitry. The inherent advantage of casting provides a 30% improvement of cooling over conventional extrusion heatsink designs.

5.Punch Bass (Models 150S & 200S) – Helps correct for acoustical deficiencies in the listening environment by helping produce full range sound without adding excessive boost.. The Punch Bass control is a narrow band adjustment at 45Hz switchable from 0dB to +6dB to +12dB.

5.Punch Bass (All Other Models) – Helps correct for acoustical deficiencies in the listening environment by helping produce full range sound without adding excessive boost.. The Punch Bass control is a narrow band adjustment at 45Hz variable from 0dB to + 18dB. Connection is made with a cable using RJ-45 and can be installed under the dash for remote control access.

4

DESIGN FEATURES

6.Internal Crossover (Models 150S & 200S) – Is a built-in 12dB/octave Butterworth filter selectable between 120Hz High-Pass (HP),, All Pass (AP), or 80Hz Low-Pass (LP) operation.

6.Variable Crossover (All Other Models) – Is a built-in 12dB/octave Butterworth filter selectable for High-Pass (HP), All Pass (AP), or Low-Pass (LP) operation variable from 50Hz to 210Hz.

7.Gain Control – The input gain control is preset to match the output of most source units. It can be adjusted to match output levels from a variety of source units.

8.RCA Input Jacks – The industry standard RCA jacks provide an easy connection for signal level input. They are gold-plated to resist the signal degradation caused by corrosion.

9.High Level Inputs – The high level inputs use a detachable connector terminated with 20 AWG leads. These inputs should be used if the source unit has only speaker line (high level) outputs and not RCA outputs.

10.Speaker Terminals – These gold-plated connectors are immune to corrosion that can cause signal deterioration. Model 200S utilizes a barrier strip that will accept #10 spade lugs or bare speaker and power wires sized from 10-18 AWG. All other models use heavy duty, gold-plated terminal block connectors (+ and –) will accept wire sizes from 8 AWG to 18 AWG.

INSTALLATION

INSTALLATION CONSIDERATIONS

The following is a list of tools needed for installation:

Volt/Ohm Meter Wire strippers Wire crimpers Wire cutters

#2 Phillips screwdriver Battery post wrench

Hand held drill w/assorted bits 1/8" diameter heatshrink tubing Assorted connectors

Adequate Length—Red Power Wire Adequate Length—Remote Turn-on Wire Adequate Length—Black Grounding Wire

This section focuses on some of the vehicle considerations for installing your new Amplifier. Preplanning your system layout and best wiring routes will save installation time. When deciding on the layout of your new system, be sure that each component will be easily accessible for making adjustments.

! CAUTION: If you feel unsure about installing this system yourself, have it installed by a qualified technician.

! CAUTION: Before installation, disconnect the battery negative (-) terminal to prevent damage to the unit, fire and/or possible injury.

Before beginning any installation, follow these simple rules:

1.Be sure to carefully read and understand the instructions before attempting to install the Unit.

2.For safety, disconnect the negative lead from the battery prior to beginning the installation.

3.For easier assembly, we suggest you run all wires prior to mounting your Source Unit in place.

4.Route all of the RCA cables close together and away from any high current wires.

5.Use high quality connectors for a reliable installation and to minimize signal or power loss.

6.Think before you drill! Be careful not to cut or drill into gas tanks, fuel lines, brake or hydraulic lines, vacuum lines or electrical wiring when working on any vehicle.

7.Never run wires underneath the vehicle. Running the wires inside the vehicle provides the best protection.

8.Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through metal, especially the firewall.

5

INSTALLATION

9.ALWAYS protect the battery and electrical system from damage with proper fusing. Install the appropriate fuse holder and fuse on the +12V power wire within 18” (45.7 cm) of the battery terminal.

10.When grounding to the chassis of the vehicle, scrape all paint from the metal to ensure a good, clean ground connection. Grounding connections should be as short as possible and always be connected to metal that is welded to the main body, or chassis, of the vehicle.

MOUNTING LOCATIONS

The mounting position of your amplified subwoofer will have a great effect on the sound performance produced.

Engine Compartment

Never mount this unit in the engine compartment. Mounting the unit in the engine compartment will void your warranty.

Trunk Mounting

Mounting the amplifier vertically will provide the best cooling of the amplifier.

Mounting the amplifier on the floor of the trunk will work but provides less cooling capability than vertical mounting.

Mounting the amplifier upside down to the rear deck of the trunk will not provide proper cooling and will severely affect the performance of the amplifier and is strongly not recommended.

Passenger Compartment Mounting

Mounting the amplifier in the passenger compartment will work as long as you provide a sufficient amount of air for the amplifier to cool itself. If you are going to mount the amplifier under the seat of the vehicle, you must have at least 1" (2.54cm) of air gap around the amplifier's heatsink.

Mounting the amplifier with less than 1" (2.54cm) of air gap around the amplifier's heatsink in the passenger compartment will not provide proper cooling and will severely affect the performance of the amplifier and is strongly not recommended.

BATTERY AND CHARGING

Amplifiers will put an increased load on the vehicle's battery and charging system. We recommend checking your alternator and battery condition to ensure that the electrical system has enough capacity to handle the increased load of your stereo system. Stock electrical systems which are in good condition should be able to handle the extra load of any Rockford Fosgate amplifier without problems, although battery and alternator life can be reduced slightly. To maximize the performance of your amplifier, we suggest the use of a heavy duty battery and an energy storage capacitor.

WIRING THE SYSTEM

! CAUTION: If you do not feel comfortable with wiring your new unit, please see your local Authorized Rockford Fosgate Dealer for installation.

! CAUTION: Before installation, disconnect the battery negative (-) terminal to prevent damage to the unit, fire and/or possible injury.

CAUTION: Avoid running power wires near the low level input cables, antenna, ! power leads, sensitive equipment or harnesses. The power wires carry

substantial current and could induce noise into the audio system.

1.Plan the wire routing. Keep RCA cables close together but isolated from the amplifier's power cables and any high power auto accessories, especially electric motors. This is done to prevent coupling the noise from radiated electrical fields into the audio signal. When feeding the wires through the firewall or any metal barrier, protect them with plastic or rubber grommets to prevent short circuits. Leave the wires long at this point to adjust for a precise fit at a later time.

2.Prepare the RED wire (power cable) for attachment to the amplifier by stripping 1/2" of insulation from the end of the wire. Insert the bared wire into the B+ terminal and tighten the set screw to secure the cable in place.

6

INSTALLATION

NOTE: The B+ cable MUST be fused 18" or less from the vehicle's battery. Install the fuseholder under the hood and prepare the cable ends as stated above. Connections should be water tight.

3.Trim the RED wire (power cable) within 18" of the battery and strip1/2"of insulation from the end of the wire. Cut the wire loop that is attached to the fuseholder in half and splice the fuse into the power line using appropriate inline connectors. Use the section of cable that was trimmed earlier and connect it to the other end of the fuseholder.

4.Strip 1/2" from the battery end of the power cable and crimp a large ring terminal to the cable. Use the ring terminal to connect to the battery positive terminal. DO NOT install the fuse at this time.

5.Prepare the BLACK wire (Ground cable) for attachment to the amplifier by stripping 1/2" of insulation from the end of the wire. Insert the bared wire into the GND terminal and tighten the set screw to secure the cable in place. Prepare the chassis ground by scraping any paint from the metal surface and thoroughly clean the area of all dirt and grease. Strip the other end of the wire and attach a ring connector. Fasten the cable to the chassis using a non-anodized screw and a star washer.

6.Prepare the REM turn-on wire for connection to the amplifier by stripping 1/2" of insulation from the wire end. Insert the bared wire into the REM terminal and tighten the set screw to secure the cable into place. Connect the other end of the REM wire to a switched 12 volt positive source.

The switched voltage is usually taken from the source unit's accessory lead. If the source unit does not have this output available, the recommended solution is to wire a mechanical switch in line with a 12 volt source to activate the amplifier.

7.Securely mount the amplifier to the vehicle or amp rack. Be careful not to mount the amplifier on cardboard or plastic panels. Doing so may enable the screws to pull out from the panel due to road vibration or sudden vehicle stops.

8.Connect the source signal to the amplifier by plugging the RCA cables/high level inputs into the input jacks at the amplifier.

9.Connect the speakers. Strip the speaker wires 1/2" and insert into the speaker terminal and tighten the set screw to secure into place. Be sure to maintain proper speaker polarity. DO NOT chassis ground any of the speaker leads as unstable operation may result.

10.Perform a final check of the completed system wiring to ensure that all connections are accurate. Check all power and ground connections for frayed wires and loose connections which could cause problems.

NOTE: Follow the diagrams for proper signal polarity.

!

CAUTION: These amplifiers are not recommended for impedance loads below 2Ω

stereo and 4Ω bridged (mono).

Power

Connection -

Models 150S &

200S

7

INSTALLATION

Power

Connections -

Models 300S,

400S & 500S

Power

Connections -

Model 700S

Bridged/Mono Wiring – Models 150S & 200S

(R+) Gray

High

(R–) Gray/Black

(L+) White

Level

(L–) White/Black

Input

OR

 

RCA OR High Level input connection

CAUTION: Use only one input configuration.

! Using both the RCA and High Level inputs will cause undesirable operation.

8

Rockford Fosgate 150S, 200S, 300S, 400S, 500S User Manual

INSTALLATION

2-Channel Wiring – Models 150S & 200S

(R+) Gray

High

(R–) Gray/Black

(L+) White

Level

(L–) White/Black

Input

OR

 

RCA OR High Level input connection

Bridged/Mono Wiring – All Other Models

RCA OR High Level input connection

Gain - left and right set equally

2-Channel Wiring – All Other Models

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(R+) Gray

 

 

High

 

 

 

 

 

 

 

 

(R–) Gray/Black

 

 

 

 

 

 

 

 

 

 

(L+) White

 

 

Level

 

 

 

 

 

 

 

 

(L–) White/Black

 

 

Input

 

 

 

 

 

OR

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(R+) Gray

 

 

High

 

 

 

 

 

 

 

 

 

 

 

 

(R–) Gray/Black

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(L+) White

 

 

Level

 

 

 

 

 

 

 

 

 

 

 

 

(L–) White/Black

 

 

Input

 

 

 

 

 

 

 

OR

RCA OR High Level input connection

CAUTION: Use only one input configuration.

! Using both the RCA and High Level inputs will cause undesirable operation.

9

INSTALLATION

USING PASSIVE CROSSOVERS

A passive crossover is a circuit that uses capacitors and/or coils and is placed on speaker leads between the amplifier and speaker. The crossover delegates a specific range of frequencies to the speaker for optimum driver performance. A crossover network can perform one of three functions: High-Pass (capacitors), Low-Pass (inductors or coils) and Bandpass (combination of capacitor and coil).

The most commonly used passive crossover networks are 6dB/octave systems. These are easy to construct and require one component per filter. Placing this filter in series with the circuit will reduce power to the speaker by 6dB/octave above or below the crossover point depending on whether it is a high-pass or low-pass filter. More complex systems such as 12dB/octave or 18dB/octave can cause impedance problems if not professionally designed.

Passive crossovers are directly dependent upon the speaker's impedance and component value for accuracy. When passive crossover components are used in multiple speaker systems, the crossover's effect on the overall impedance should be taken into consideration along with the speaker's impedance when determining amplifier loads.

! CAUTION: These amplifiers are not recommended for impedance loads below 2Ω stereo and 4Ω bridged (mono).

L

6dB/Octave -Pass

C

6dB/Octave -Pass

L = Low-Pass (Inductor)

C = High-Pass (Capacitor) For more information, see your

Authorized Rockford Fosgate Dealer.

Freq.

 

Speaker Impedance

 

Hertz 2 OHMS

4 OHMS

8 OHMS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

L

 

 

C

 

 

L

 

 

C

 

L

 

 

C

 

80

 

4.1mH

1000mF

8.2mH

 

500mF

 

16mH

 

250mF

100

 

3.1mH

800mF

6.2mH

 

400mF

 

12mH

 

200mF

130

 

2.4mH

600mF

4.7mH

 

300mF

 

10mH

 

150mF

200

 

1.6mH

400mF

3.3mH

 

200mF

6.8mH

 

100mF

260

 

1.2mH

300mF

2.4mH

 

150mF

4.7mH

 

 

75mF

400

 

.8mH

200mF

1.6mH

 

100mF

3.3mH

 

 

50mF

600

 

.5mH

136mF

1.0mH

 

 

68mF

2.0mH

 

 

33mF

800

 

.41mH

100mF

.82mH

 

 

50mF

1.6mH

 

 

26mF

1000

 

.31mH

 

78mF

.62mH

 

 

39mF

1.2mH

 

 

20mF

1200

 

.25mH

 

66mF

.51mH

 

 

33mF

1.0mH

 

 

16mF

1800

 

.16mH

 

44mF

.33mH

 

 

22mF

.68mH

 

 

10mF

4000

 

.08mH

 

20mF

.16mH

 

 

10mF

.33mH

 

 

5mF

6000

 

51mH

 

14mF

.10mH

 

6.8mF

.20mH

 

3.3mF

9000

 

34mH

 

9.5mF

 

68mH

 

4.7mF

.15mH

 

2.2mF

12000

 

25mH

 

6.6mF

 

51mH

 

3.3mF

100mH

 

1.6mF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10

INSTALLATION

REMOTE PUNCH BASS – (Models 300S, 400S, 500S & 700S Only)

Mounting and installation

1.Find a location, either under the dash or near the center console, that gives easy access to the remote.

2. Using the screws supplied, install the mounting clip with the tabs towards t he back.

3.Route the cable for the remote and connect to both the remote and amplifed subwoofer.

4.Slip the remote onto the mounting clip until it snaps into place.

Mounting

Clip

Knob

5. Install the decal and knob onto the

Decal

remote.

 

OPERATION

ADJUSTING GAIN

Do the following individually for each channel, or both equally if bridged (mono).

NOTE: Models 150S and 200S have a single gain adjustment.

To adjust the gain setting, turn the amplifier gains all the way down. Turn the source unit volume up until distortion is audible and then turn it down a bit until the distortion is inaudible. This will be about two thirds all the way up on most source units. Next, turn the amplifier gain setting until once again distortion is audible and then back it down until the distortion is inaudible. Rockford Fosgate source units do not distort, so the volume can be used at maximum setting.

NOTE: For a more in depth setting procedure, contact Rockford Technical Support.

ADJUSTING CROSSOVER FREQUENCY

Model 200S

Placing the switch in the HP position sets the amplifier to the 120Hz High Pass mode, allowing only frequencies above the cut-off point to pass.

Placing the switch in the AP position sets the amplifier to the All Pass mode, allowing all frequencies to pass.

Placing the switch in the LP position sets the amplifier to the 80Hz Low Pass mode, allowing only frequencies below the cut-off point to pass.

11

OPERATION

All Other Models

Placing the switch in the HP position sets the amplifier to the High Pass mode, enabling frequencies above the cut-off point to pass, adjustable between 50-210Hz.

Placing the switch in the AP position sets the amplifier to the All Pass mode, preventing any crossover adjustment, allowing all frequencies to pass..

Placing the switch in the LP position sets the amplifier to the Low Pass mode, enabling frequencies below the cut-off point to pass, adjustable between 50-210Hz.

Turn the crossover adjustment knob all the way down. With the system playing, turn the crossover adjustment knob up slowly until the desired crossover point is achieved.

ACCESSORIES

Connecting PUNCH Capacitors

Maintain the power you need to your Punch Amplifier.

Connecting Links

Mount your Punch Amplifiers together for space reduction and a smooth look.

See our website for other accessories to help you get the most out of your system. www.rockfordfosgate.com

12

TROUBLESHOOTING

NOTE: If you are having problems after installation follow the Troubleshooting procedures below.

Procedure 1: Check Amplifier for proper connections.

Verify that POWER light is on. If POWER light is on skip to Step 2, if not continue.

1.Check in-line fuse on battery positive cable. Replace if necessary.

2.Verify that Ground connection is connected to clean metal of the vehicle’s chassis. Repair/replace if necessary.

3.Verify there is 10.5 - 15.5 Volts of current present at the positive battery and remote turn-on cable. Verify quality connections for both cables at amplifier, stereo, and battery/fuseholder. Repair/replace if necessary.

Procedure 2: Check Amplifier for audio output.

1.Verify good RCA/high-level input connections at stereo and amplifier. Check entire length of cables for kinks, splices, etc. Test RCA/high-level inputs for AC current with stereo on. Repair/replace if necessary.

2.Disconnect RCA/high-level input from amplifier. Connect RCA/high-level input from test stereo directly to amplifier input.

Procedure 3: Check Amplifier if you experience Turn-on Pop.

1.Disconnect input signal to amplifier and turn amplifier on and off.

2.If the noise is eliminated, connect the REM lead of amplifier to source unit with a delay turn-on module.

OR

1.Use a different 12 Volt source for REM lead of amplifier (i.e. battery direct).

2.If the noise is eliminated, use a relay to isolate the amplifier from noisy turn-on output.

Procedure 4: Check Amplifier if you experience excess Engine Noise.

1. Route all signal carrying wires (RCA, Speaker cables) away from power and ground wires.

OR

2.Bypass any and all electrical components between the stereo and the amplifier(s). Connect stereo directly to input of amplifier. If noise goes away the unit being bypassed is the cause of the noise.

OR

3.Remove existing ground wires for all electrical components. Reground wires to different locations. Verify that grounding location is clean, shiny metal free of paint, rust etc.

OR

4.Add secondary ground cable from negative battery terminal to the chassis metal or engine block of vehicle.

OR

5.Have alternator and battery load tested by your mechanic. Verify good working order of vehicle electrical system including distributor, spark plugs, spark plug wires, voltage regulator etc.

13

SPECIFICATIONS

MODELPUNCH

150S

 

200S

 

300S

Continuous Power Rating (RMS) - Measured at 14.4 Battery Volts

 

 

4Ω Load Per Channel

37.5 Watts x 2

 

50 Watts x 2

 

75 Watts x 2

 

 

2Ω Load Per Channel

75 Watts x 2

 

100 Watts x 2

 

150 Watts x 2

4Ω Load Bridged (Mono)

1500 Watts x 1

 

200 Watts x 1

 

300 Watts x 1

Dimensions: (with Endbell)

 

 

 

 

 

Height

2.4" (6.1cm)

 

2.4" (6.1cm)

 

2.4" (6.1cm)

Width

9.8" (24.89cm)

 

9.8" (24.89cm)

 

9.8" (24.89cm)

Length

10.35" (26.42cm)

 

10.35" (26.42cm)

 

11.35" (28.96cm)

Battery Fuse Rating (Amp)

20A

 

20A

 

30A

(External to Amplifier)

 

 

 

 

 

Fuse Type

ATC

 

ATC

 

ATC

 

 

 

 

 

 

 

 

 

 

 

 

MODELPUNCH

400S

 

500S

 

700S

Continuous Power Rating (RMS) - Measured at 14.4 Battery Volts

4Ω Load Per Channel

100 Watts x 2

2Ω Load Per Channel

200 Watts x 2

4Ω Load Bridged (Mono)

400 Watts x 1

Dimensions: (with Endbell)

 

Height

2.4" (6.1cm)

Width

9.8" (24.89cm)

Length

12.35" (31.42cm)

Battery Fuse Rating (Amp)

40A

(External to Amplifier)

 

Fuse Type

ATC

Signal-to-Noise Ratio

 

Crossover Slope

 

Crossover Frequency (Models 150S & 200S)

Crossover Frequency (All Other Models)

Frequency Response

Bandwidth

Damping Factor @ 4Ω (at output connector )

Slew Rate

IM Distortion (IHF)

Acceptable Signal Voltage Range

125 Watts x 2

175 Watts x 2

250 Watts x 2

350 Watts x 2

500 Watts x 1

700 Watts x 1

2.4" (6.1cm)

2.4" (6.1cm)

9.8" (24.89cm)

9.8" (24.89cm)

13.35" (33.96cm)

18.35" (46.74cm)

50A

60A

 

Not Supplied

AGU

AGU

 

 

>100dB A-weighted

12dB/octave Butterworth

Fixed 80Hz LP, AP, 120Hz HP

variable from 50Hz to 210Hz

20Hz to 20kHz ±0.5dB

20Hz to 200kHz ±3dB

>200

30 Volts/ms

<0.05%

Variable from 250mV to 6V (RCA Input) Variable from 0.5V to 11V (High Level Input)

Protection

NOMAD - Internal analog-computer output protection

 

circuitry limits power in case of overload. Thermal

 

switch shuts down the amplifier in case of overheating.

Equalization (45Hz Punch Bass) (Models 150S & 200S)

Switchable from 0dB to +6dB to +12dB

Equalization (45Hz Punch Bass) (All Other Models)

 

Variable from 0dB to +18dB @ 45Hz

Input Impedance

 

20k ohms

Specifications subject to change without notice

14

LIMITED WARRANTY INFORMATION

Rockford Corporation offers a limited warranty on Rockford Fosgate products on the following terms:

Length of Warranty

 

PUNCH Amplifiers – 2 years

All Other Amplifier Models – 3 years

Source Units – 1 year

Speakers – 1 year

90 days on speaker, amplifier and source unit B-stock (receipt required)

What is Covered

This warranty applies only to Rockford Fosgate products sold to consumers by Authorized Rockford Fosgate Dealers in the United States of America or its possessions. Product purchased by consumers from an Authorized Rockford Fosgate Dealer in another country are covered only by that country’s Distributor and not by Rockford Corporation.

Who is Covered

This warranty covers only the original purchaser of Rockford product purchased from an Authorized Rockford Fosgate Dealer in the United States. In order to receive service, the purchaser must provide Rockford with a copy of the receipt stating the customer name, dealer name, product purchased and date of purchase.

Products found to be defective during the warranty period will be repaired or replaced (with a product deemed to be equivalent) at Rockford's discretion.

What is Not Covered

1.Damage caused by accident, abuse, improper operations, water, theft

2.Any cost or expense related to the removal or reinstallation of product

3.Service performed by anyone other than Rockford or an Authorized Rockford Fosgate Service Center

4.Any product which has had the serial number defaced, altered, or removed

5.Subsequent damage to other components

6.Any product purchased outside the U.S.

7.Any product not purchased from an Authorized Rockford Fosgate Dealer

Limit on Implied Warranties

Any implied warranties including warranties of fitness for use and merchantability are limited in duration to the period of the express warranty set forth above. Some states do not allow limitations on the length of an implied warranty, so this limitation may not apply. No person is authorized to assume for Rockford Fosgate any other liability in connection with the sale of the product.

How to Obtain Service

Please call 1-800-669-9899 for Rockford Customer Service. You must obtain an RA# (Return Authorization number) to return any product to Rockford Fosgate. You are responsible for shipment of product to Rockford.

Ship to: Electronics

Ship to: Speakers

Rockford Corporation

Rockford Acoustic Design

Warranty Repair Department

Speaker Returns

2055 E. 5th Street

2356 Turner Ave. NW

Tempe, AZ 85281

Grand Rapids, MI 49544

RA#: _________________________

RA#: ____________________

15

Français

INTRODUCTION

Cher client,

Toutes nos félicitations pour avoir acheté la meilleure marque d'amplificateurs pour automobile. Chez Rockford Fosgate nous sommes des mordus de la reproduction musicale à son meilleur. C’est pourquoi nous sommes heureux que vous ayez choisi notre produit. Des années d’expertise en ingénierie, de savoir-faire et d’essais poussés nous ont permis de créer une vaste gamme de produits capables de reproduire toute la clarté et la richesse musicales que vous méritez.

Pour obtenir les meilleurs résultats, nous vous recommandons de faire installer votre nouvel appareil par un distributeur agréé Rockford Fosgate formé spécialement par notre Institut de formation technique Rockford (RTTI). Prenez soin de lire la garantie et conservez votre reçu ainsi que l’emballage d'origine pour usage ultérieur.

Pour monter un excellent système, il ne suffit pas de posséder un super produit et d’assurer une installation qualifiée compétente. Vous devez veiller à ce que votre installateur utilise des accessoires d’origine fournis par Connecting Punch. Connecting Punch a tout ce qu’il vous faut, des câbles RCA aux câbles de haut-parleur, en passant par les câbles d’alimentation et les connecteurs de batterie. Insistez pour les avoir! Après tout, votre nouveau système ne mérite rien de moins.

Pour compléter votre nouvelle image Rockford Fosgate, commandez des accessoires Rockford tels que T-shirts, vestes, chapeaux et lunettes de soleil.

Pour obtenir une brochure gratuite sur les produits Rockford Fosgate et les accessoires Rockford, appelez aux États-Unis le 480-967-3565 ou faxez au 480-967-8132.

Pour tous les autres pays, appelez le +001-480-967-3565 ou faxez au +001-480-967-8132.

PRATIQUEZ UNE ÉCOUTE SANS RISQUESMD

Une exposition continue à des niveaux de pression acoustique supérieurs à 100 dB peut causer une perte d'acuité auditive permanente. Les systèmes audio de forte puissance pour auto peuvent produire des niveaux de pression acoustique bien audelà de 130 dB. Faites preuve de bon sens et pratiquez une écoute sans risques

Si vous avez encore des questions à propos de ce produit, même après avoir lu ce manuel, contactez votre distributeur agréé Rockford Fosgate. Si vous avez besoin d'aide, appelez-nous au 1-800-669-9899. Veuillez avoir les numéros de modèle et de série, ainsi que la date d'achat de l'appareil à portée de main lorsque vous appelez.

Le numéro de série est indiqué sur l’extérieur de l’emballage. Veuillez l’inscrire ci-dessous dans l'espace réservé à cet effet. Il permettra de vérifier votre garantie et de retrouver votre appareil en cas de vol.

Numéro de série :_______________________________________

Numéro de modèle : ____________________________________

TABLE DES MATIÈRES

Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 Consignes de sécurité . . . . . . . . . . . . . . . . . 3 Particularités techniques . . . . . . . . . . . . . 4-5 Installation . . . . . . . . . . . . . . . . . . . . . . 5-11

Considérations concernant l'installation . 5 Emplacements de montage . . . . . . . . . . 6 Batterie et charge . . . . . . . . . . . . . . . . . 6 Câblage du système. . . . . . . . . . . . . . . . 6 Utilisation de filtres . . . . . . . . . . . . . . . 10 Basses Punch à télécommande (300S-700S seulement). . . . . . . . . . . . . 11

Fonctionnement . . . . . . . . . . . . . . . . . . 11-12

Réglage du gain. . . . . . . . . . . . . . . . . . 11 Réglage de la fréquence du filtre passif . 11

Accessoires. . . . . . . . . . . . . . . . . . . . . . . . 12 Dépannage . . . . . . . . . . . . . . . . . . . . . . . . 13 Caractéristiques . . . . . . . . . . . . . . . . . . . . 14 Informations sur la garantie limitée . . . . . . 15

NOTE : consultez chaque section pour de plus amples informations.

2

AVANT DE COMMENCER

Bienvenue à Rockford Fosgate ! Ce manuel vise à informer le propriétaire, le vendeur et l’installateur de l’appareil. Si vous désirez apprendre rapidement comment installer ce produit, consultez la section Installation du manuel. Reportez-vous à la Table des matières pour d’autres informations. Nous nous efforçons de faire en sorte que toutes les informations contenues dans ce manuel soient à jour. Mais comme nous améliorons constamment nos produits, nous nous réservons le droit de modifier ces informations sans aucun préavis.

CONSIGNES DE SÉCURITÉ

Le symbole accompagnant le mot « AVERTISSEMENT » signale à l'utilisateur la présence d’instructions importantes. Le non-respect de ces instructions causera des blessures graves ou la mort.

Le symbole accompagnant l’expression « MISE EN GARDE » signale à l'utilisateur la présence d’instructions importantes. Le non-respect de ces instructions peut causer des blessures ou endommager l’appareil.

! MISE EN GARDE : pour éviter des blessures et ne pas endommager l'appareil, veuillez lire et suivre les instructions du manuel. Notre but est que ce système vous donne du plaisir et non des maux de tête.

! MISE EN GARDE : si vous vous sentez incapable d’installer l’appareil vous-même, confiez la tâche à un technicien Rockford Fosgate qualifié.

! MISE EN GARDE : avant d'entamer l'installation, déconnectez la broche négative (-) de la batterie pour éviter tout risque de blessures, d’incendie ou de dommages à l'appareil.

CONTENU DE L'EMBALLAGE

Amplificateur à 2 voies, modèle Punch 150S, 200S, 300S, 400S, 500S ou 700S

Manuel d'installation et d'utilisation

Kit de matériel de montage

Kit de télécommande de basses Punch avec cordon

1 faisceau d'entrée haut niveau

1 clé Allen 3/32 po

1 clé Allen 9/64 po

1 connecteur de fusible (150S, 200S, 300S,

400S et 500S seulement)

1 fusible 20 A (150S, 200S)

1 fusible 30 A (300S)

1 fusible 40 A (400S)

1 fusible 50 A (500S)

Le kit de matériel inclus avec chaque amplificateur contient le matériel de montage nécessaire pour fixer l'ampli au véhicule et les couvercles d'extrémité à l'ampli.

REMARQUE : reportez-vous à la section des caractéristiques en ce qui concerne les fusibles recommandés pour les modèle 700S

Visitez notre site Web pour obtenir les dernières informations sur tous les produits Rockford.

www.rockfordfosgate.com

3

Français

PARTICULARITÉS TECHNIQUES

Connexions -

1

6

8

5

7

9

2

3

4

 

 

 

 

 

 

 

 

 

Modèles 150S

 

 

 

 

 

 

 

 

 

et 200S

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10

10

 

 

 

 

1

 

2

3

 

 

4

Connexions d'alimentation - Modèles 300S, 400S et 500S

Connexions

1 2

3

4

d'alimentation - Modèle 700S

Connexions -

5

6 7

8

7 9 6

Modèles 300S,

 

 

 

 

400S, 500S et

 

 

 

 

700S

 

 

 

 

 

10

 

 

10

1.Voyant d'alimentation à DEL – La DEL s'allume lorsque l'appareil est allumé.

2.Borne REM – Cette cosse à fourche permet d'allumer et d'éteindre à distance l'amplificateur lorsqu'un courant de +12 V c.c. est envoyé.

3.Bornes d'alimentation – Les connexions d'alimentation et de masse de l'ampli sont plaquées or et peuvent accueillir des câbles de calibre allant jusqu'à 4 AWG (8 AWG pour le modèle 350S), ce qui permet de maximiser la capacité de courant d'entrée de l'ampli.

4.Dissipateur thermique en aluminium coulé – Le dissipateur thermique en aluminium coulé de l'amplificateur Power dissipe la chaleur générée par les circuits de l'amplificateur. L'avantage intrinsèque du moulage est qu'il améliore de 30 % le refroidissement par rapport aux modèles conventionnels de dissipateur thermique à extrusion.

5.Basses Punch (modèles 150S et 200S) – Cette commande permet de corriger les faiblesses acoustiques de l'environnement en produisant un son pleine gamme sans amplification excessive. La commande de basses Punch permet un réglage à bande étroite sur 45 Hz pouvant être commuté de 0 dB à +6 dB et +12 dB.

5.Basses Punch (tous les autres modèles) – Cette commande permet de corriger les faiblesses acoustiques de l'environnement en produisant un son pleine gamme sans amplification excessive. La commande de basses Punch permet un réglage à bande étroite sur 45 Hz pouvant être ajusté de 0 dB à +18 dB. La connexion se fait à l'aide d'un câble RJ-45 pouvant être installé sous le tableau de bord pour permettre un accès par télécommande.

4

PARTICULARITÉS TECHNIQUES

6.Filtre interne (modèles 150S et 200S) – Filtre de Butterworth intégré de 12 dB/octave pour modes passe-haut (HP) 120 Hz, passe-tout (AP) ou passe-bas (LP) 80 Hz.

6.Filtre variable (tous les autres modèles) – Filtre de Butterworth intégré de 12 dB/octave pour modes passe-haut (HP), passe-tout (AP) ou passe-bas (LP), réglable de 50 à 210 Hz.

7.Commande de gain – La commande de gain d'entrée est préréglée de manière à correspondre à la sortie de la plupart des unités source. Elle peut être réglée en fonction d'une variété d'unités source.

8.Prises d'entrée RCA – Les prises RCA de norme industrielle permettent une connexion facile pour les entrées de signaux. Elles sont plaquées or pour résister à la détérioration de signal due à l'effet de la corrosion.

9.Entrées de signaux élevés – Les entrées de signaux élevés utilisent un connecteur détachable terminé par des fils de calibre 20 AWG. Utilisez ces entrées si la source audio est dotée de sorties (de grande puissance) pour haut-parleur seulement et non pas de sorties RCA.

10.Bornes de haut-parleur – Ces connecteurs plaqués or sont à l'épreuve de la corrosion qui peut nuire au signal. Le modèle 200S utilise une barrette de connexion pouvant accepter des cosses carrées no 10 ou des câbles nus de haut-parleur et d'alimentation de calibre variant de 10 à 18 AWG. Tous les autres modèles utilisent des connecteurs robustes plaqués or aux bornes (+ et -) et qui acceptent des câbles de calibre 8 à 18 AWG

INSTALLATION

CONSIDÉRATIONS CONCERNANT L’INSTALLATION

Voici la liste d’outils requis pour l’installation : Voltmètre-ohmmètre

Pince à dénuder Pince à sertir Coupe-fils

Tournevis à embout cruciforme no 2 Clé de borne de batterie

Perceuse à main avec mèches assorties

Tube thermorétrécissable de 1/8 po de diamètre

Connecteurs assortis

Longueur adéquate — Fil d’alimentation rouge

Longueur adéquate — Fil d’allumage à distance

Longueur adéquate — Fil de masse noir

Cette section traite de points concernant le véhicule dont il faut tenir compte pour l’installation de votre nouvel ampli. Vous sauverez du temps en planifiant à l’avance la disposition du système et du câblage. Assurez-vous, entre autres, que chaque composant du système est facilement accessible pour les réglages.

! MISE EN GARDE : si vous vous sentez incapable d’installer l’appareil vous-même, confiez la tâche à un technicien qualifié.

! MISE EN GARDE : avant d'entamer l'installation, déconnectez la broche négative (-) de la batterie pour éviter tout risque de blessures, d’incendie ou de dommages à l'appareil.

Avant de commencer l’installation, suivez ces règles toutes simples :

1.Prenez soin de bien lire et comprendre les instructions avant d’installer l’appareil.

2.Par mesure de sécurité, veuillez débrancher le fil négatif de la batterie avant de commencer l’installation.

3.Pour faciliter le montage, nous vous suggérons de dérouler tous les fils avant d’installer l’appareil.

4.Acheminez tous les câbles RCA de façon groupée, à l’écart des fils à courant élevé.

5.Utilisez des connecteurs de haute qualité pour assurer une installation fiable et minimiser la perte de signal ou de puissance.

6.Réfléchissez avant de percer quoique ce soit! Faites attention de ne pas couper ou percer le réservoir d’essence, les conduites de carburant, de frein, hydrauliques ou de dépression, ou le câblage électrique lorsque vous travaillez sur un véhicule.

7.Ne faites jamais passer les fils sous le véhicule. Il vaut mieux les installer à l’intérieur du véhicule pour assurer une meilleure protection.

8.Évitez de faire passer les fils par dessus ou à travers des bords tranchants. Tout fil acheminé à travers du métal, un pare-feu en particulier, doit être protégé avec des bagues en caoutchouc ou plastique.

5

Français

INSTALLATION

9.Protégez TOUJOURS la batterie et le circuit électrique des dommages potentiels à l’aide de fusibles. Installez un porte-fusible et un fusible appropriés sur le câble d’alimentation de +12 V à moins de 45,7 cm (18 po) de la borne de batterie.

10.Préparez la masse du châssis en grattant toute trace de peinture de la surface métallique afin d’assurer une bonne mise à la masse. Les connexions de masse doivent être aussi courtes que possible et toujours connectées à du métal soudé à la carrosserie ou au châssis du véhicule.

EMPLACEMENTS DE MONTAGE

L’emplacement de l’ampli influe grandement sur la qualité du son obtenu.

Compartiment moteur

Ne montez jamais cet appareil dans le compartiment moteur. Cela entraînerait l’annulation de la garantie.

Montage dans le coffre

Un montage vertical de l’ampli assure un refroidissement optimal.

Le montage de l’ampli sur le plancher du coffre est acceptable mais offre un refroidissement moindre que le montage vertical.

Le montage de l’ampli à l’envers, sur la tablette arrière, n’assure pas un refroidissement satisfaisant, nuit à la performance de l’ampli et est, pas conséquent, fortement déconseillé.

Montage dans l’habitacle

Le montage de l’ampli dans l’habitacle passager est acceptable à condition qu’il reçoive suffisamment d’air pour se refroidir. Si vous comptez installer l’ampli sous le siège du véhicule, prévoyez un écartement d’au moins 2,54 cm (1 po) autour du dissipateur thermique de l’ampli.

Un écartement inférieur à cela n’assure pas un refroidissement satisfaisant, nuit à la performance de l’ampli et est, pas conséquent, fortement déconseillé.

BATTERIE ET CHARGE

Les amplificateurs exercent une charge accrue sur la batterie et le système de charge du véhicule. Nous vous conseillons de vérifier l’état de l’alternateur et de la batterie pour vous assurer que le système électrique puisse supporter la charge accrue de votre système stéréo. Les systèmes électriques ordinaires en bon état sont normalement capables de fournir sans problème la charge supplémentaire requise par les amplis Rockford Fosgate. Toutefois, la durée de vie de la batterie et de l’alternateur peut s’en trouver affectée légèrement. Pour maximiser la performance de votre ampli, nous vous suggérons d’utiliser une batterie à usage intensif et un condensateur de stockage d’énergie.

CÂBLAGE DU SYSTÈME

! MISE EN GARDE : si vous ne vous sentez pas à l’aise pour effectuer vous-même le câblage de votre nouvel appareil, veuillez confier l’installation à votre distributeur agréé Rockford Fosgate.

!MISE EN GARDE : avant d'entamer l'installation, déconnectez la broche négative (-) de la batterie

pour éviter tout risque de blessures, d’incendie ou de dommages à l'appareil.

!MISE EN GARDE : évitez de faire passer les fils d’alimentation près des câbles d’entrée de signaux

faibles, de l’antenne, des câbles d'alimentation, des équipements ou faisceaux sensibles. Les fils d’alimentation transportent un courant élevé et peuvent produire du bruit dans le système audio.

1.Planifiez l’acheminement des fils. Gardez les câbles RCA ensemble mais en les isolant des câbles d’alimentation de l’ampli et des autres accessoires automobiles de forte puissance, particulièrement les moteurs électriques, pour éviter que le signal audio ne subisse d'interférence de bruit provenant de champs de rayonnement électriques. Si vous faites passer les fils par un pare-feu ou autre barrière métallique, protégez-les à l’aide de bagues en caoutchouc ou en plastique pour éviter les courts-circuits. Conservez toute la longueur des fils pour l’instant. Vous l’ajusterez plus tard.

2.Préparez le fil ROUGE (câble d’alimentation) qui devra être relié à l’ampli en dénudant 1/2 po de son extrémité. Insérez la partie dénudée dans la borne B+, puis fixez le fil en vissant la vis sans tête.

6

INSTALLATION

REMARQUE : le câble B+ DOIT comporter un fusible à 18 pouces ou moins de la batterie du véhicule. Installez le porte-fusible sous le capot et préparez les extrémités de câble tel qu’indiqué ci-dessus. Les connexions doivent être étanches.

3.Coupez le fil ROUGE (câble d’alimentation) à moins de 18 pouces de la batterie et dénudez 1/2 po de son extrémité. Coupez en deux la boucle reliée au porte-fusible et épissez le fusible sur le fil d’alimentation à l’aide de connecteurs en ligne appropriés. Utilisez la section de fil coupée plus tôt et connectez-la à l’autre extrémité du porte-fusible.

4.Dénudez 1/2 po de l’extrémité de batterie du câble d’alimentation et sertissez une grosse cosse à anneau sur le câble. Connectez la cosse à la borne positive de la batterie. N’installez pas le fusible pour l'instant.

5.Préparez le fil NOIR (câble de mise à la masse) qui devra être relié à l’ampli en dénudant 1/2 po de son extrémité. Insérez la partie dénudée dans la borne GND, puis fixez le fil en vissant la vis sans tête. Préparez la masse du châssis en grattant toute trace de peinture de la surface métallique et en nettoyant soigneusement pour éliminer tout dépôt de saleté et de graisse. Dénudez l’autre extrémité du fil et fixez un connecteur en anneau. Fixez le câble au châssis à l’aide d’une vis non anodisée et une rondelle en étoile.

6.Préparez le fil d’activation REM qui devra être relié à l’ampli en dénudant 1/2 po de son extrémité. Insérez la partie dénudée dans la borne REM, puis fixez le fil en vissant la vis sans tête. Connectez l’autre extrémité du fil REM à une source positive commutée de 12 volts. La tension commutée provient généralement de l’antenne ou du câble d’accessoires de la source audio. Si la source audio ne comporte pas de telles sorties, nous recommandons de raccorder un interrupteur mécanique en ligne avec une source de 12 volts pour activer l’ampli.

7.Montez solidement l’ampli sur le véhicule ou le rack d’ampli. Prenez soin de ne pas le fixer sur des panneaux en carton ou en plastique. Les vis pourraient en effet se décoller des panneaux sous l’effet des vibrations de la route ou des arrêts soudains du véhicule.

8.Connectez le signal à l’ampli en branchant les câbles RCA/entrées de signaux élevés dans les prises d’entrée de l’ampli.

9.Connectez les haut-parleurs : dénudez les fils des haut-parleurs de 1/2 po et insérez la partie dénudée dans la borne du haut-parleur, puis serrez la vis sans tête pour fixer le tout. Veillez à respecter la polarité des hautparleurs. NE mettez PAS les fils de haut-parleur à la masse sur le châssis car cela pourrait causer un fonctionnement instable.

10.Effectuez une vérification finale du câblage pour vous assurer que toutes les connexions sont bien mises. Vérifiez toutes les connexions d’alimentation et de mise à la masse en vue de fils effilochés et de connexions desserrées pouvant causer des problèmes.

REMARQUE : vérifiez les polarités de signal à l’aide des schémas.

! MISE EN GARDE : ces amplificateurs ne sont pas recommandés pour des charges d'impédance inférieures à 2 Ω stéréo et 4 Ω pontées (mono).

Connexion d'alimentation - Modèles 150S et 200S

7

Français

INSTALLATION

Connexions d'alimentation - Modèles 300S, 400S et 500S

Connexions d'alimentation - Modèle 700S

Câblage ponté/mono – Modèles 150S et 200S

Connexion pour entrée RCA

OU de signaux élevés

MISE EN GARDE : utilisez un type de configuration

! d'entrée seulement. L'utilisation à la fois d'entrées RCA et de signaux élevés produira un effet indésirable.

8

Loading...
+ 50 hidden pages