4 www.robofiber.com
RB-GES401-POE Gigabit Ethernet Switch
Installation
• Please use Cat5e or Cat6 TP cables not exceeding 100m in length to
connect to network PD devices
• Connect power adapter to mains and to back power jack
• Power the RB-GES401-POE switch and check LED status for proper
operation
Gigabit Ethernet PoE Port Up-link Ethernet Port
Troubleshooting
• Make sure all cables are following the EIA/TIA568A or 568B
specifications
• If one end is following EIA/TIA 568A or 568B, the other end of
same cable must be same identical type
• Check PD devices for power consumption, no single port should
exceed 30W load
• Check that all PoE PD devices do not exceed 60W total consumption
Gigabit PoE Ethernet
Switch
RB-GES401-POE
User Manual
Uplink
PoE
PWR
5-
Port Ethernet Switch with 4 PoE
2 3
RB-GES401-POE Gigabit Ethernet Switch
RB-GES401-POE Gigabit Ethernet Switch
Gigabit Power-over-Ethernet Ethernet Switch
Order Information
RB-GES401-POE Gigabit 5 port switch with 4 PoE ports (60W total PoE power)
Description
The RB-GES401-POE is a simple but reliable Gigabit Ethernet switch. Switch has a total
PoE output of 60 watts.
With the RB-GES401-POE switch, PDs (such as IP Security Cameras, wireless access
points) can be installed at powered through the unit itself. Four ports on the switch can
provide a total of 60W of PoE power (15W per port) and a fifth port is available for
10/100/1000Base-Tx connectivity.
Switch has its own AC power adapter providing DC 48V @ 1.3A. RB-GES401-POE offers
five Gigabit Ethernet ports with automatic link speed, duplex and auto direct/crossover
negotiation and connectivity. This small switch is ideal for unmanaged data network
hubs.
Features
• 5 x 10/100/1000Base-Tx ports switch
• Conforms to IEEE802.3, IEEE 802.3u, IEEE 802.3ab, IEEE802.3af, IEEE802.3at
• 4 port PoE enabled ports, 65W power adapter
• Gigabit full-rate network throughput with 10G bandwidth backplane
• IEEE802.3x flow control
• FCC, CE compliant
For best performance and reach, please use only Cat5e and Cat6 rated cables.
Lower grade cables will prevent proper operation of the Ethernet switch.
Contents of package
• RB-GES401-POE switch
• AC 90-240V to DC48V power adapter
• User manual
Technical Specifications
Power
AC 90-240V IN, DC48V OUT external power supply,
65W max power. Switch in standby (no PoE PD
devices connected needs only 8W of power)
Interfaces
5 x RJ45 10/100/1000 Mbps half/full duplex auto,
max. reach 328ft (100meters)
Ethernet Standards
IEEE 802.3/802.3u/802.3ab/802.3af/802.3at
PoE Output
Pin Assignment and Polarity: 1/2 (+), 3/6 (-), Output
Power: up to 30W/port, orange LEDs, not exceeding
60W total PoE output
Connectors
Shielded RJ-45, EIA 568A and 568B
Switch characteristics
10G backplane capacity, max transfer rate 148,800
pps for 1000Mbps, 4K MAC address table
Dimensions
119mm x 85mm x 28mm, metal casing
Mounting
Desktop
Environmental Conditions
Operating Ambient Temperature: 0 to 40℃
Operating Humidity: Maximum 85%, Noncondensing
Storage Temperature: -30 to 70℃
Storage Humidity: Maximum 95%, Non-condensing
Application Diagram
Loading...