TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS |
2 |
PRECAUTIONS TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY |
4 |
INSTALLATION GUIDE |
4 |
GROUNDING INSTRUCTIONS |
5 |
PRODUCT DIAGRAM |
6 |
CONTROL PANEL |
7 |
INSTALLING THE TURNTABLE |
8 |
OPERATION INSTRUCTIONS |
8 |
UTENSILS GUIDE |
12 |
COOKING TECHNIQUES |
13 |
CLEANING AND CARE |
14 |
BEFORE CALLING FOR SERVICE |
15 |
SPECIFICATIONS |
15 |
WARRANTY |
16 |
1
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic safety precautions should be followed, including the following:
WARNING- To reduce the risk of burns, electric shock, fire, injury to persons or exposure to excessive microwave energy:
1.Read all instructions before using the appliance.
2.Read and follow the specific "PRECAUTIONS TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY" on page 4.
3.This appliance must be grounded. Connect only to properly grounded outlet. See "GROUNDING INSTRUCTIONS" on page 5.
4.Install or locate this appliance only in accordance with the provided installation instructions.
5.Some products such as whole eggs and sealed containers -for example, closed glass jarsare able to explode and should not be heated in this oven.
6.Use this appliance only for its intended use as described in this manual. Do not use corrosive chemicals or vapors in this appliance. This type of oven is specifically designed to heat, cook, or dry food. It is not designed for industrial or laboratory use.
7.As with any appliance, close supervision is necessary when used by children.
8.To reduce the risk of fire in the oven cavity:
1)Do not overcook food. Carefully attend appliance when paper, plastic, or other combustible materials are placed inside the oven to facilitate cooking.
2)Remove wire twist-ties from paper or plastic bags before placing bag in oven.
3)If materials inside the oven should ignite, keep oven door closed, turn oven off, and disconnect the power cord or shut off power at the fuse or circuit breaker panel.
4)Do not use the cavity for storage purposes. Do not leave paper products, cooking utensils or food in the cavity when not in use.
9.Liquids, such as water, coffee, or tea are able to be overheated beyond the boiling point without appearing to be boiling due to surface tension of the liquid. Visible bubbling or boiling when the container is removed from the microwave oven is not always present. THIS COULD RESULT IN VERY HOT LIQUIDS SUDDENLY BOILING OVER WHEN A SPOON OR OTHER UTENSIL IS INSERTED INTO THE LIQUID. To reduce the risk of injury to person:
1)Do not overheat the liquid.
2)Stir the liquid both before and halfway through heating it.
3)Do not use straight-sided containers with narrow necks.
4)After heating, allow the container to stand in the microwave oven for a short time before removing the container.
5)Use extreme care when inserting a spoon or other utensil into the container.
10.Do not heat oil or fat for deep-frying. It is difficult to control the temperature of oil in microwave oven.
11.Pierce foods with heavy skins such as potatoes, whole squash, apples and chestnuts before cooking.
12.The contents of feeding bottles and baby jars should be stirred or shaken and the temperature should be checked before serving in order to avoid burns.
2
IMPORTANT SAFETY INSTRUCTIONS (continued)
13.Cooking utensils may become hot because of heat transferred from the heated food. Potholders may be needed to handle the utensil.
14.Do not cover or block any openings on the appliance.
15.Do not store or use this appliance outdoors. Do not use this product near water, for example, near a kitchen sink, in a wet basement, near a swimming pool, or similar locations.
16.Do not operate this appliance if it has a damaged cord or a plug, if it is not working properly or if it has been damaged or dropped.
17.Do not immerse cord or plug in water. Keep cord away from heated surface. Do not let cord hang over edge of table or counter.
18.Use only thermometers, which are specifically designed for use in microwave ovens.
19.Do not operate any heating or cooking appliance beneath this appliance.
20.Be certain the glass tray and roller rings are in place when you operate the oven.
21.This appliance should be serviced only by qualified service personnel, contact nearest authorized service facility for examination, repair, or adjustment.
22.When cleaning surfaces of door and oven that comes together on closing the door, use only mild, nonabrasive soaps, or detergents applied with a sponge or soft cloth.
SAVE THESE INSTRUCTIONS
3
PRECAUTIONS TO AVOID POSSIBLE EXPOSURE TO
EXCESSIVE MICROWAVE ENERGY
1.Do not attempt to operate this oven with the door-open since open-door operation can result in harmful exposure to microwave energy. It is important not to defeat or tamper with the safety interlocks.
2.Do not place any object between the oven front face and the door or allow soil or cleaner residue to accumulate on sealing surfaces.
3.Do not operate the oven if it is damaged. It is particularly important that the oven door close properly and that there is no damage to the:
1)Door (bent),
2)Hinges and latches (broken or loosened),
3)Door seals and sealing surfaces.
4.The oven should not be adjusted or repaired by anyone except properly qualified service personnel.
INSTALLATION GUIDE
1.Make sure that all the packing materials are removed from the inside of the door.
2.Check the oven for any damage, such as misaligned or bent door, damaged door seals and sealing surface, broken or loose door hinges and latches and dents inside the cavity or on the door. If there is any damage, do not operate the oven but contact qualified service personnel.
3.This microwave oven must be placed on a flat, stable surface to hold its weight and the heaviest food likely to be cooked in the oven.
4.Do not place the oven where heat, moisture, or high humidity are generated, or near combustible materials.
5.For correct operation, the oven must have sufficient airflow. Allow 20cm of space above the oven, 10cm at back and 5cm at both sides. Do not cover or block any openings on the appliance. Do not remove feet on which oven stands.
6.Do not operate the oven without glass tray, roller support, and shaft in their proper positions.
7.Make sure that the power supply cord is undamaged and does not run under the oven or over any hot or sharp surface.
8.The socket must be readily accessible so that it can be easily unplugged in an emergency.
4
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of an electrical short circuit, grounding reduces risk of electric shock by providing an escape wire for the electric current.
WARNING: Improper use of the grounding plug can result in a risk of electric shock.
Consult a qualified electrician or serviceman if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded, and either:
1) If it is necessary to use an extension cord, use only a 3-wire extension cord that has a 3-blade grounding plug and a 3-slot receptacle that will accept the plug on the appliance. The marked rating of the extension cord shall be equal to or greater than the electrical rating of the appliance, or 2) Do not use an extension cord. If the power supply cord is too short, have a qualified electrician or serviceman install an outlet near the appliance.
ELECTRICAL REQUIREMENTS
The electrical requirements are a 120 volt 60 Hz, AC only, 15 amp.
It is recommended that a separate circuit serving only the oven be provided.
The oven is equipped with a 3-prong grounding plug. It must be plugged into a wall receptacle that is properly installed and grounded.
POWER SUPPLY CORD
A short power supply cord is provided to reduce the risks resulting from becoming entangled in or tripping over a longer cord.
Longer cord sets or extension cords are available and may be used if care is exercised in their use.
If long cord or extension cord is used
a)The marked electrical rating of the cord set or extension cord should be at least as great as the electrical rating of the appliance.
b)The extension cord must be a grounding-type 3-wire cord, and the longer cord should be arranged so that it will not drape over the counter top or table top where it can be pulled on by children or tripped over unintentionally.
NOTE:
·If you have any questions about the grounding or electrical instructions, consult a qualified electrician or service person.
RADIO OR TV INTERFERENCE
Should there be any interference caused by the microwave oven to your radio or TV, check that the microwave oven is on a different circuit, relocated the radio or TV as far away from the oven as feasible or check position and signal of receiving antenna.
5
PRODUCT DIAGRAM
1.Door Lock System
2.Oven Window
3.Roller Ring
4.Door Release Button
5.Control Panel
6.Spatter Shield (Do not remove)
7.Glass Tray
6
CONTROL PANEL
MENU ACTION SCREEN
Cooking time, power, indicators and present time are displayed.
TIME COOK
Press to set cooking time.
TIME DEFROST
Quick defrost function that alternates defrost and stand times to quickly and effectively defrost foods.
WEIGHT DEFROST
Programmed defrosting based on the weight of the foods to be defrosted.
POWER
Press to set power levels.
CLOCK
Press to set current time.
KETCHEN TIMER
Press to set timer function.
MENU PADS
There are six kinds of cook menus. Press to set auto cook function.
EXPRESS COOK (1-6)
There are six kinds of cooking time (from one minute to six minutes) for high power level. Press to set express cook function.
NUMBER PADS (0-9)
Press to enter time, the weight of defrosted food or power level.
STOP/CANCEL
Press to pause or cancel a cooking program.It is also used to set child lock function.
MEMORY (0)
Press to set memory function for the oven.
START/+30 SEC
Press to start a cooking program. It is also used to set quick start function or to increase cooking time during cooking.
7
INSTALLING THE TURNTABLE
Never place the glass tray upside down.
The glass tray should never be restricted.
Both the glass tray and turntable ring assembly must always be used during cooking.
All food and containers of food should always be placed on the glass tray for cooking.
If the glass tray or turntable ring assembly cracks or breaks, contact your nearest authorized service center.
OPERATION INSTRUCTIONS
If you want to pause a cooking program, please press STOP/CANCEL pad once, then press START/+30 SEC. pad to restart the cooking program, but if you pressSTOP/CANCEL pad twice, the cooking program will be canceled.
SETTING THE CLOCK
1.In standby mode, press CLOCK pad.
2.Use the number pads to enter the correct time.
3.Press CLOCK pad again.
NOTE: This is a 12 hour clock. When the oven is first plugged in or when power resumes after a power interruption, the display will show 0:00. During cooking, you can press CLOCK pad to check the present time.
SETTING THE OVEN TIMER
1.In standby mode, pressKITCHEN TIMER pad.
2.Enter the amount of time by pressing the number pads.
3.Press START/+30 SEC. pad to start the program.
NOTE: The longest time you can set is 99 minutes and 99 seconds. You can cancel the function by pressing STOP/CANCEL pad.
SETTING A COOKING PROGRAM
A One-stage Cooking
1.Place food into oven and close the door.
2.Press TIME COOK pad.
3.Use the number pads to set cooking time.
4.Press POWER pad.
5.Use the number pads to enter power level.
6.Press START/+30 SEC. pad to start the program.
8
OPERATION INSTRUCTIONS (continued)
Use single digit to set a cooking power level:
Number pad |
Power Level |
Number pad |
Power Level |
|
|
|
|
1,0 |
PL10 (100%) |
4 |
PL4 (40%) |
|
|
|
|
9 |
PL9 (90%) |
3 |
PL3 (30%) |
|
|
|
|
8 |
PL8 (80%) |
2 |
PL2 (20%) |
|
|
|
|
7 |
PL7 (70%) |
1 |
PL1 (10%) |
|
|
|
|
6 |
PL6 (60%) |
0 |
PL0 (0%) |
|
|
|
|
5 |
PL5 (50%) |
|
|
|
|
|
|
NOTE:
·During cooking, you can press POWER pad to check the cooking power.
·During cooking, you can press START/+30 SEC. pad continually to increase the cooking time. The longest cooking time you can set is 99 minutes and 99 seconds.
B. Two-stage Cooking
Some recipes require different stages of cooking at different temperatures.
1.SET STAGE 1:
Follow steps from 1 to5 in “One-stage Cooking”.
2.SET STAGE 2:
Follow steps from 1 to5 in “One-stage Cooking”. (Most 2-stage recipes use lower power for second stage.) 3. Press START/+30 SEC. pad to start the program.
NOTE:
·Following steps from 1 to 3 in Time Defrost program or Weight Defrost program also can be set in two-stage cooking for any stage.
TIME DEFROST
1.Place food into oven and close the door.
2.Press TIME DEFROST pad.
3.Enter desired defrosting time by pressing correct number pads.
4.Press START/+30 SEC. pad to start the program.
NOTE:
·During cooking, you can press START/+30 SEC. pad continually to increase the defrosting time. The longest defrosting time you can set is 99 minutes and 99 seconds.
·During cooking, maybe you need to pause the program to turn food over, then close the door and press START/+30 SEC. pad to resume.
9
OPERATION INSTRUCTIONS (continued)
WEIGHT DEFROST
1.Place food into oven and close the door.
2.Press WEIGHT DEFROST pad.
3.Enter the weight of food by pressing number pads.
4.Press START/+30 SEC. pad to start the program. NOTE:
·The weight of food you can set is between 4 oz and 100 oz.
·During cooking, maybe you need to pause the program to turn food over, then close the door and press START/+30 SEC. pad to resume.
EXPRESS COOK
This function can help you to set a microwave cooking program quickly without setting the power level. Place food into oven and close the door, then press any EXPRESS COOK pad (1-6), the oven will start the program automatically at full power level. During cooking, you can press START/+30 SEC. pad continually to increase the cooking time. The longest cooking time you can setis 99 minutes and 99 seconds.
QUICK START
This function can help you to set a microwave cooking program quickly without setting the power level. Place food into oven and close the door, then press START/+30 SEC. pad continually to set cooking time, the oven will start the program automatically at full power level. During cooking, you can press START/+30 SEC. pad continually to increase the cooking time. The longest cooking time you can set is 99 minutes and 99 seconds.
MEMORY FUNCTION
This function can help you to start the stored cooking programs directly. The system can store three cooking programs.
A Store the first cooking program
1.In standby mode, Press MEMORY (0) pad once.
2.Set a one-stage cooking or two-stage cooking program.
3.Press START/+30 SEC. pad to confirm the program.
B. Store the second cooking program
1.In standby mode, Press MEMORY (0) pad twice.
2.Set a one-stage cooking or two-stage cooking program.
3.Press START/+30 SEC. pad to confirm the program.
10
Loading...