OPERATORS MANUAL
MODELS 2032-OS, 2048-OS, 204830-OS, 3068-OS RIDGID ON-SITE STORAGE EQUIPMENT
DANGER
•Do NOT put fuels, flammables, explosives or hazardous materials inside these products.
•Gasoline, solvents, gun powder or other munitions, dynamite, propane, acetylene or other such products can explode if stored inside these products.
•Use these products ONLY for storing and transporting electric or hand tools and equipment, and other similar materials.
•Failure to follow these warnings or modifications or other uses of these products could result in death, serious injury or property damage.
WARNING
For Models 2048-OS and 204830-OS:
To prevent electric shock, explosion, fire and/or serious personal injury when using storage chest with:
Extension Cord -
•Follow all Extension Cord manufacturer’s Warnings and Instructions.
•After removing knock-out, insert Rapid Pass™ rubber grommet. Do NOT insert extension cord through hole without grommet in place (see figure 8, on page 3).
•Only use a three-wire extension cord with all three prongs intact. Never remove the round grounding prong.
•Extension cord must be connected to a 120 Volt GFCI protected outlet with proper ground. If GFCI outlet is not available, use an extension cord with GFCI protection built in.
•Check the insulation and plugs of extension cord before using. Do NOT use cord if it is worn or damaged.
•Do NOT overload extension cord.
•Remove extension cord from the Rapid Pass™ hole before moving or transporting storage chest.
•Only use an extension cord that is rated for outdoor use.
•Do NOT connect extension cord to outlet that also supplies critical safety equipment with power.
Cordless Power Tool Battery Chargers -
•See Charger’s Owner’s Manual for proper use and care of charger and batteries. Follow all Warnings and Instructions provided with your battery charger.
•Place chargers and electrical connections in tray.
•Chargers are Dry location use only. Do NOT expose to liquid, vapor, or rain. Should your charger become wet, Do NOT attempt to use. Unplug extension cord from supply before handling wet charger or cords.
•Only use chargers and batteries that are intact and operating properly.
•Do NOT touch metal prongs when plugging charger into extension cord.
•Keep flammable materials like paper or rags away from charger, cords or connections.
•Do NOT place or attempt to charge lead acid, car type batteries in storage chest.
WARNING
Keep hands clear when closing lid. Failure to do so could result in severe injury.
–ATTENTION–
Read and understand all instructions and warnings before operating or using this product.
–NOTICE–
Any modification or unintended use of this product shall immediately void all manufacturers warranties. Manufacturer disclaims all liability for injuries to persons or
property resulting from any modification to, or unintended use of this product.
PADLOCK INSTALLATION INSTRUCTIONS FOR ALL UNITS
Figure 1
U-Bolt
Figure 2 |
Lock Shackle |
|
7/8"-1"
Figure 3 (measure height when lock is closed)
TOOLS REQUIREDOne wrench with 7/16” socket. |
3. |
Guide the U-bolt through the two holes in the back of |
|
PADLOCK INFORMATIONPadlock with 7/8”–1” shackle |
|
the lock housing (figure 2). |
|
height (figure 3) (recommended Master No 5 or equiva- |
4. |
Secure the U-bolt with the two nylon lock nuts sup- |
|
lent, not included). |
|
plied. |
|
|
|
5. |
Repeat the procedure for the second lock. |
1. |
Open your padlock and slide the U-bolt over the lock |
6. |
To lock, close lid and push bottom of padlock until |
|
shackle. |
|
lock “clicks” closed. |
2. |
Slide the lock through the lock housing on the front of |
7. |
To open, turn key and open lid. |
|
the box (figure 1). |
|
|
PROP
ARM
LOCKING
SUPPORT ARM
Figure 4
3068-OS PROP-ARM INSTRUCTIONS
TOP POINT
FOR FIELD DESK CAPABILITY
1.Hold cover in the middle with one hand, pull left prop arm outward and disengage from retaining clasp.
2.Switch hands on cover and repeat (figure 4) for opposite side.
3.Hold the cover at it’s top point with your right hand. With your left hand, slightly pull the locking support arm at the hinge until there is a slight bend (figure 4).
4.Slowly lower cover until it is parallel with the ground. Be sure the prop arms are engaged in slots as shown below (figure 5). Make sure prop arms are fully engaged forward so that the prop arms are perpendicular to the cover.
5.The final position for Field Desk Capability is shown in Figue 6
Figure 5
SIDE
VIEW
ENGAGEMENT
POINT
Figure 6
WARNING
Do NOT use cover as a step.
2
Loading...