ELECTRIC CHAIN SAW
OWNER’S MANUAL
®
ENGLISH
MODELS: M12510US, M15012US, M15014US, M15014AS, M30016US,
M30016AS, M30016AW, M35016UW, M35016AW
IMPORTANT: Read and understand this manual before assemblingoroperatingthischainsaw.Improperuseofsawcancause severe injury. Keep this manual for future reference.
Contents |
|
IMPORTANT SAFETY INFORMATION .............................................................................. |
3 |
Before Operating Saw ....................................................................................................................... |
3 |
While Operating Saw......................................................................................................................... |
3 |
Kickback ............................................................................................................................................ |
4 |
Maintenance and Storage of Chain Saw........................................................................................... |
5 |
UNPACKING ....................................................................................................................... |
6 |
PRODUCT IDENTIFICATION ............................................................................................. |
6 |
CHAIN SAW NAMES AND TERMS.................................................................................... |
6 |
ASSEMBLY......................................................................................................................... |
7 |
SAW CHAIN TENSION ADJUSTMENT.............................................................................. |
8 |
OPERATING CHAIN SAW.................................................................................................. |
9 |
Filling Oil Tank ................................................................................................................................... |
9 |
Oiling Chain....................................................................................................................................... |
9 |
Clearing sprocket cover of debris.................................................................................................... |
10 |
Extension Cords.............................................................................................................................. |
10 |
Cutting with the Chain Saw ............................................................................................................. |
11 |
Felling a Tree (Cutting Down a Tree) ............................................................................................... |
11 |
Limbing a Tree................................................................................................................................. |
12 |
Bucking a Log.................................................................................................................................. |
13 |
Trimming a Tree (Pruning) ............................................................................................................... |
13 |
CLEANING AND MAINTENANCE ................................................................................... |
15 |
Cleaning Saw Body......................................................................................................................... |
15 |
Care of Guide Bar ........................................................................................................................... |
15 |
Sharpening Saw Chain.................................................................................................................... |
15 |
Replacing Saw Chain...................................................................................................................... |
16 |
STORAGE......................................................................................................................... |
17 |
TECHNICAL SERVICE..................................................................................................... |
17 |
REPLACEMENT PARTS AND ACCESSORIES............................................................... |
17 |
REPAIR SERVICE............................................................................................................. |
17 |
Warranty Service............................................................................................................................. |
17 |
Non-Warranty Service..................................................................................................................... |
17 |
TROUBLESHOOTING ...................................................................................................... |
18 |
WARRANTY INFORMATION............................................................................................ |
19 |
ILLUSTRATED PARTS BREAKDOWN/DESGLOSE ILUSTRADO DE PARTES/SCHÉMA |
|
DES PIÈCES..................................................................................................................... |
62 |
PARTS CENTRAL/CENTRAL DE PIEZAS/DÉPÔT DE PIÈCES..................................... |
65 |
www.desatech.com |
2 |
113005 |
IMPORTANT SAFETY INFORMATION
WARNING: When using an electric chain saw, basic safety precautions shouldalwaysbefollowedtoreducethe risk of fire, electric shock, and injury to persons, including the following:
READ ALL INSTRUCTIONS.
Make sure you read and understand all instructionsinImportantSafetyInformation onpages3through5.Improperuseofthis chainsawcancausesevereinjuryordeath from fire, electrical shock, body contact with moving chain, or falling wood.
BEFORE OPERATING SAW
1.Readandunderstandthisowner’smanualbefore operating chain saw.
2.Watch what you are doing. Use common sense. Do not operate saw when you are tired.
3.Use chain saw for cutting wood only. Do not use chain saw for purpose not intended. Do not use for cutting plastic, masonry, etc.
4.Only well-instructed adults should operate chain saw. Never allow children to operate chain saw.
5.Use only electrical voltage noted on model plate of chain saw.
6.Useonlyextensioncordsmarkedforoutdooruse. See page 10 for extension cord requirements.
7.Do not operate chain saw
•while under the influence of alcohol, medication, or drugs
•in rain or in damp or wet areas
•where highly flammable liquids or gases are present
•ifsawisdamaged,adjustedwrong,ornotfully and securely assembled
•if trigger does not turn saw on and off. Chain must stop moving when you release trigger. Have faulty switch replaced by authorized service center (see Technical Service, page 17).
•while in a hurry
•while in tree or on a ladder unless trained to do so
8.Wear snug-fitting clothes when operating chain saw.Donotwearlooseclothingorjewelry.They can get caught in moving saw chain.
9.Wear the following safety gear when operating chain saw.
•heavy-duty gloves (wear rubber gloves when working outdoors)
•steel-toed safety footwear with non-skid soles
•eye protection such as safety glasses, goggles, or face screen
• safety hard hat |
|
• ear mufflers or ear plugs |
|
• hair covering to contain long hair |
|
• face or dust mask (if working in dusty areas) |
|
10. Before cutting, always provide the following: |
|
• clear work area |
|
• secure footing |
ENGLISH |
polarizedplug(onebladeiswiderthantheother). |
|
• planned retreat path from falling tree |
|
11. Inspecttreebeforecuttingdown.Makesurethereare |
|
no dead limbs or branches that may fall on you. |
|
12. Toreducetheriskofelectricshock,thissawhasa |
|
This plug will fit in a polarized outlet only one |
|
way. If the plug does not fit fully in the outlet of |
|
your extension cord, reverse the plug. If it still |
|
does not fit, a polarized extension cord will be |
|
necessary. Do not change the plug in any way. |
|
WHILE OPERATING SAW
1.Stay alert. Use common sense while operating chain saw.
2.Keep work area clean. Cluttered areas invite injuries.
3.Beawareofextensioncordwhileoperatingchain saw. Be careful not to trip over cord. Keep cord away from chain and operator at all times.
4.Keep children, animals, and bystanders away from chain saw and extension cord. Only chain saw user should be in work area.
5.Do not cut down a tree unless you are trained or have expert help.
6.Iftwoormorepersonsperformbuckingandfelling operations at the same time, provide plenty ofdistancebetweenoperations.Providedistance of at least twice the height of tree being felled.
7.Secure wood you are cutting by using clamps or chocks.
8.Grip chain saw firmly with both hands. Never operatechainsawwithonehand.Neverusehand guard as handle.
9.Keep finger off trigger until ready to make cut.
10.Before starting chain saw, make sure chain is not touching anything.
11.To guard against electrical shock, avoid body contact with grounded objects such as pipes, fences, and metal posts.
12.Keep all parts of body away from chain when saw is running.
13.Donotforcechainsawwhilecutting.Applylight pressure. It will do the job better and safer at the rate for which it was intended.
14.Cut small brush and saplings with extreme care. Slender material may catch in chain and be whipped toward you. This could also pull you off balance.
Continued
113005 |
3 |
www.desatech.com |
IMPORTANT SAFETY INFORMATION
Continued
15.When cutting limb or tree trunk that is under tension, use extreme caution. Be alert for wood springing back. When wood tension is released, limb could spring back and strike operator causing severe injury or death.
16.Carry chain saw from one place to another
•with saw stopped and unplugged
•by holding front handle (never use hand guard as handle)
•with finger off trigger
•with guide bar and chain to rear
WARNING: This product contains chemicals known to the State of California to cause cancer or birth defects, or other reproductive harm.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the state of California) to cause cancer, birth defects,or other reproductive harm.Some examples of these chemicals are:
•lead from lead-based paints
•crystalline silica from bricks and cement and other masonry products
•arsenicandchromiumfromchemicallytreated lumber
Your risk from these exposures varies, depending on how often you do this typeofwork.Toreduceyourexposureto thesechemicals:workinawellventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
KICKBACK
WARNING:Kickbackmayoccurwhen the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut. Tip contact in some cases may cause a lightningfastreversereaction,kickingthe guidebarupandbacktowardstheoperator. Pinching the saw chain along the top of the guide bar may push the guide bar rapidly back towards the operator. Either of these reactions may cause you to lose control of the saw which could result in serious injury to user.
Kickback Safety Devices OnThis Saw
This saw has a low-kickback chain and reduced kickback guide bar. Both items reduce the chance of kickback. Kickback can still occur with this saw.
Follow assembly instructions on pages 7 and 8. Do not remove front hand guard. Do not replace front hand guard with substitute.
The following steps will reduce the risk of kickback.
•Use both hands to grip saw while saw is running. Use firm grip. Thumbs and fingers must wrap around saw handles.
•Keep all safety items in place on saw. Make sure they work properly.
•Do not overreach or cut above shoulder height.
•Keep solid footing and balance at all times.
•Stand slightly to left side of saw. This keeps your body from being in direct line with chain.
•Do not let guide bar nose touch anything when chain is moving (see Figure 1).
Direction |
Do Not Let Guide |
|
|
|
Bar Touch Here |
90° Quadrant |
|
Figure1-KickbackHazardExample:DoNotLet Nose of Guide Bar Touch Object While Chain is Moving
www.desatech.com |
4 |
113005 |
IMPORTANT SAFETY INFORMATION
Continued
•Never try cutting through two logs at same time. Only cut one log at a time.
•Donotburyguidebarnoseortryplungecut(boring into wood using guide bar nose).
•Watchforshiftingofwoodorotherforcesthatmay pinch chain.
•Use extreme caution when reentering a previous cut.
•Use low-kickback chain and guide bar supplied with this chain saw. Only replace these parts with chains and guide bars listed in this manual.
•Never use dull or loose chain. Keep chain sharp with proper tension.
Saw Maintenance and Kickback Safety
Followmaintenanceinstructionsinthismanual.Proper cleaning of saw and chain and guide bar maintenance can reduce chances of kickback. Inspect and maintain sawaftereachuse.Thiswillincreasetheservicelifeof yoursaw.Note:Even with proper sharpening, risk of kickback can increase with each sharpening.
MAINTENANCE AND STORAGE OF CHAIN SAW
1.Unplug chain saw from power source
•when not in use
•before moving from one place to another
•before servicing
•before changing accessories or attachments, such as saw chain and guard
2.Inspect chain saw before and after each use. Check saw closely if guard or other part has been damaged. Check for any damage that may affect operator safety or operation of saw. Check for alignment or binding of moving parts. Check for broken or damaged parts. Do not use chain saw if damage affects safety or operation. Have damage repaired by authorized service center.
3.Maintain chain saw with care.
•Never expose saw to rain.
•Keep chain sharp, clean, and lubricated for better and safer performance.
•Followstepsoutlinedinthismanualtosharpen chain.
•Keep handles dry, clean, and free of oil and grease.
•Keep all screws and nuts tight.
•Inspect power cord often. If damaged, have repaired by authorized service center.
•Never carry chain saw by power cord.
•Never yank power cord to unplug it.
•Keep power cord from heat, oil, and sharp edges.
•Inspect extension cords often and replace if damaged.
4.When servicing, use only identical replacement parts.
5.When not in use, always store chain saw
•in a high or locked place, out of children’s reach
•in a dry place
•inacarryingcaseorwithscabbardoverguidebar
Save these instructions. It is your guide to safe and proper operation of this chain saw.
ENGLISH
113005 |
5 |
www.desatech.com |
UNPACKING
1. Remove all items from carton.
2.Check all items for any shipping damage. If you find any damage or if any parts are missing, call TechnicalServicesat1-800-858-8501forprompt service.
PRODUCT IDENTIFICATION
Front Handle |
Hand Guard |
Guide Bar Nose |
Front Handle |
Hand Guard |
Guide Bar Nose |
|
|
|
|
||
|
|
|
|
|
|
|
Oil Cap |
|
Oil Cap |
||
Switch Lockout |
|
|
Switch Lockout |
|
|
Rear Handle |
|
Guide Bar |
Rear Handle |
|
Guide Bar |
Power Cord |
|
Saw Chain |
Power Cord |
|
Saw Chain |
|
|
|
|||
|
Chain Tensioning Screw |
|
Chain Tensioning Screw |
||
|
Trigger |
|
|
Trigger |
|
Cord Hitch |
|
|
Cord Hitch |
|
|
Figure 2 - Chain Saw Model M12510US, M15012US, M15014US, M15014AS, M30016US, M30016AS
Figure 3 - Chain Saw Model M30016AW,
M35016UW, M35016AW
CHAIN SAW NAMES AND TERMS
Bucking Process of cutting a felled tree or log into lengths.
Chock Block or wedge used to secure wood from moving.
Felling Process of cutting down a tree.
Felling Cut Final cut when felling a tree. Make this cut on opposite side of tree from notching cut. Front Handle Located at front of saw body. Front Hand Guard Shield between front handle and guide bar. Protects left hand while using saw. Guide Bar Metal bar that extends from saw body. The guide bar supports and guides chain.
Guide Bar Nose Tip or end of guide bar.
Guide Bar Retainer Bolt-like fastener that holds guide bar in place during assembly and operation of chain saw.
Kickback Quick backward and upward motion of guidebar.Kickbackmayoccurwhentipofguidebar touches an object while chain is moving. The guide bar will kick up and back towards operator.
Limbing Process of cutting limb(s) from a felled tree. Low-Kickback Chain Chain that reduces chance of kickback as required by ANSI B175.1.
Normal Cutting Position Stanceusedwhilemaking bucking and felling cuts.
NotchingCut Notch cut in tree that directs fall of tree.
Oiler Control System for oiling guide bar and chain. Power Head Chainsawwithoutchainandguidebar. Also known as saw body.
Pushback(Kickback,Pinch) Rapidpushbackofchain saw. Pushback may occur if chain along top of guide bar is pinched, caught, or contacts a foreign object. Rear Handle Handle located at rear of saw body.
Reduced Kickback Guide Bar Guide bar that reduces chance of kickback.
Replacement Chain Chain that complies withANSI B175.1whenusedwithaspecificsaw.Itmaynotmeet ANSI requirements when used with other saws.
Saw Chain (Chain) Loop of chain having cutting teeth for cutting wood. The motor drives chain. The guide bar supports chain.
Spiked Bumper (Spike) Pointed teeth at front of saw body beside guide bar. Keep spiked bumper in contact with wood when felling or bucking. It helps maintain position of saw while cutting.
Sprocket Toothed wheel that drives chain. Switch Devicethatcompletesorinterruptselectrical circuit to motor of saw.
Switch Linkage This device connects switch totrigger. It moves switch when you squeeze trigger. Switch Lockout Device that reduces accidental starting of saw.
www.desatech.com |
6 |
113005 |
CHAIN SAW NAMES AND TERMS
Continued
Trigger Device that turns saw on and off. Squeezing trigger turns saw on. Releasing trigger turns saw off. Trimming (Pruning) Processofcuttinglimb(s)from a living tree.
Undercut An upward cut from underside of log or limb. This is done while in normal cutting position and cutting with top of guide bar.
Unibody Main body of chain saw.
ASSEMBLY
Note:Some models are pre-assembled.Assembly is not needed on these models.
See Saw Chain Tension Adjustment, pages 8 and 9.
WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain.
IMPORTANT:Do not clamp chain saw in vise during assembly.
1.Lay chain out flat.
2.Loosen and remove guide bar nut and sprocket cover.
3.Rotate guide bar retainer so that it is positioned parallel to guide bar slot (see Figure 4).
4.Installguidebarontosawbody.Assemblecenter slotofguidebarontoguidebarboltandguidebar retainer. Note: Make sure the head of the guide bar retainer slides through the guide bar slot as shown in Figure 4.
Drive
Sprocket
Guide Bar
|
|
|
E |
|
N |
L |
O |
|
|
||
U |
|
|
|
|
|
|
|
|
|
|
Guide Bar Retainer |
|
|
|
Positioned Parallel |
|
|
|
to Guide Bar Slot |
Figure 4 - Unlocking Guide Bar Retainer
5. Rotate guide bar retainer 90 degrees as shown in |
|
Figure 5. |
|
6. Placechainarounddrivesprocket,alongtopgroove |
|
of guide bar, and around guide bar nose. Note: |
|
Make sure cutting edges of chain are facing in |
|
rightdirection.Positionchainsocuttingedgeson |
|
top of guide bar face guide bar nose (see Figure |
ENGLISH |
will vibrate badly and will not cut. |
|
6 and indicator on side cover of saw). |
|
CAUTION:Donotplacechainonsaw |
|
backwards. If chain is backwards, saw |
|
|
|
7.Insert tab of sprocket cover into slot on unibody and rotate sprocket cover onto guide bar bolt until sprocket cover rests against guide bar (see Figure 7, page 8).
8.Place guide bar nut, removed in step 2, on guide bar bolt.
IMPORTANT:Tightenguidebarnutfingertight only.
Drive
Sprocket
Guide Bar
|
K |
E |
D |
|
|
||
C |
|
|
|
|
|
|
|
O |
|
|
|
L |
|
|
|
Guide Bar Retainer Rotated 90 Degrees to Guide Bar Slot
Figure 5 - Locking Guide Bar Retainer
Towards Guide Bar
Nose
Cutting Edge
Figure 6 - Saw Chain Direction
Continued
113005 |
7 |
www.desatech.com |
ASSEMBLY
Continued
9.Turning chain tensioning screw, adjust position of adjustment block until it is aligned and inserted into the round adjusting hole on guide bar (see Figures 7 and 8). Turning screw counterclockwise will move adjustment block to rear of guide bar.Turning screw clockwise will move adjustment block to front of guide bar.
10.Ifneeded,readjustguidebarnuttofingertightonly.
11.Adjust saw chain tension. Follow steps under
Saw Chain Tension Adjustment, pages 8 and 9.
WARNING:Maintainproperchaintension always. A loose chain will increase the risk of kickback. A loose chain may jump out of guide bar groove.This may injure operator and damage chain. A loose chain will cause chain, guide bar, and sprocket to wear rapidly.
IMPORTANT!
Failure to follow these instructions when tensioning sawchainwilldamagesawandvoidthewarranty.For additional information call 1-800-858-8501.
|
Adjusting Hole |
Slot |
Guide Bar Bolt |
|
New saw chains will stretch. Check chain tension frequently when first used and tighten when chain becomes loose around guide bar.
|
|
Step |
|
|
|
|
|
|
|
2 |
|
|
|
|
|
Step |
Bushing |
|
|
|
|
|
|
1 |
|
|
|
|
|
||
|
|
|
|
|
|
|
|
Sprocket Cover Tab |
Guide Bar Nut |
|
|
|
|
|
|
|
|
|
|
|
|
||
Figure 7 - Installing Sprocket Cover |
|
|
|
|
|
||
|
|
|
|
Ifchainbecomesloosearoundguide |
|||
Chain Tensioning |
|
|
|
bar, allow chain to cool then... |
|||
Screw |
|
|
|
|
|
|
|
Adjustment Block |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Figure 8 - Chain Tensioning Screw and |
|
|
|
|
|
||
Adjustment Block Location |
|
|
|
O |
|
||
|
|
|
|
|
|
||
|
|
|
|
O |
S |
||
|
|
|
|
L |
|
||
SAW CHAIN TENSION |
|
|
|
|
E |
||
|
|
|
|
N |
|||
ADJUSTMENT |
|
|
|
|
|
|
|
WARNING: Unplug chain saw from |
|
|
|
|
|
||
powersourcebeforeadjustingsawchain |
|
|
|
|
|
||
tension. |
|
|
|
|
|
|
|
WARNING: Cutting edges on chain |
|
Loosen nut... |
|
|
|
||
are sharp. Use protective gloves when |
|
|
|
|
|||
handling chain. |
|
|
|
|
|
|
|
www.desatech.com |
|
|
8 |
|
|
|
113005 |
SAW CHAIN TENSION ADJUSTMENT
Continued
N
T
Turn chain tensioning screw
clockwise to tension saw chain...
|
Guide Bar |
Approx. |
|
1/8" |
|||
|
|
Pull chain to check tension. Guide links should not come out of guide bar groove...
OPERATING CHAIN SAW
WARNING:Readandunderstandthis owner’smanualbeforeoperatingthissaw. Makecertainyoureadandunderstandall
Important Safety Information, pages 3 through5.Improperuseofthischainsaw can cause severe injury or death from fire,electricalshock,orbodycontactwith moving chain, or falling wood.
FILLING OIL TANK
1.Remove oil cap.
2.Fill oil tank with SAE #30 motor oil. Note: For temperatures below 30°F, use SAE #10 oil. For temperatures above 75°F, use SAE #40 oil.
3.Replace oil cap at once. Tighten oil cap firmly for good seal. This will avoid oil seepage from tank.
4.Wipe off excess oil.
Note:Itisnormalforoiltoseepwhensawisnotinuse. Empty oil tank after each use to prevent seepage.
OILING CHAIN
Manual Oil System
Always check oil level before using saw. Do not attempt to operate the oil system while saw is in operation. To oil chain, press squeeze bulb. Oil will feed onto the guide bar and chain. Press squeeze bulb at least once before each cut. Check oil level often by looking at oil level through side of oil bottle (see Figure 9).
Oil Squeeze Bulb
ENGLISH
IG |
|
|
T |
H |
|
T |
||
|
|
E |
|
|
N |
Oil Bottle
Makesurechainmovesfreelyaround guide bar then tighten nut.
Figure 9 - Oil Squeeze Bulb and Oil Bottle
Location
Continued
113005 |
9 |
www.desatech.com |
OPERATING CHAIN SAW
Continued
CLEARING SPROCKET COVER OF DEBRIS
While operating the chain saw, wood chips, small twigs, and other debris can occasionally build up inside the sprocket cover. To properly maintain the saw and keep it in good working order, periodic removal of this debris may be required. To properly clear debris from the sprocket cover:
1.Unplug chain saw.
2.Loosen and remove guide bar nut (see Figure 10).
3.Turn chain tensioning screw counterclockwise to loosen chain until sprocket cover is easily removed.
4.After sprocket cover is removed, clear all chips, twigs, and debris.
WARNING: Use caution when clearing debris that is around chain. Cutting edges on chain are sharp. Use protective gloves when working around or handling chain.
5.Once debris has been removed, follow steps 7 through 11 on pages 7 and 8 in the Assembly section to re-assemble the sprocket cover to the chain saw.
Wood Chips, Twigs,
and Debris
EXTENSION CORDS
Use proper extension cords with this saw. Use only extensioncordsmarkedforoutdooruse.Thecordmust be marked with suffix W or W-A following the cord type designation. Example: SJTW-A or SJTW.
Usepropersizedcordwiththissaw.Cordmustbeheavy enoughtocarrycurrentneeded.Anundersizedcordwill causevoltagedropatsaw.Sawwilllosepowerandoverheat. Follow cord size requirements listed below.
Cord Length |
AWG Cord Size |
|
|
25 feet |
16 AWG |
50 feet |
16 AWG |
100 feet |
16 AWG |
150 feet |
14 AWG |
Models M12510US, M15012US, M15014US,
M15014AS
Cord Length |
AWG Cord Size |
|
|
25 feet |
16 AWG |
50 feet |
16 AWG |
100 feet |
14 AWG |
150 feet |
12 AWG |
Models M30016US, M30016AS, M30016AW,
M35016UW, M35016AW
Keep cord away from cutting area. Make sure cord does not catch on branches or logs during cutting. Inspect cords often. Replace damaged cords.
Thischainsawisdesignedwithanextensioncordhitch thatpreventstheextensioncordfrombeingpulledloose during use. To use, form a loop with the end of the extension cord, insert loop into slot in rear of handle, andplaceloopovercordhitch(seeFigure11). Gently pull loop against cord hitch until slack is removed. Plug extension cord into chain saw cord.
Power Cord
Cord Hitch
Sprocket Cover |
Guide Bar Nut |
|
Extension Cord |
Figure 10 - Removing and Clearing Sprocket
Cover of Debris
Figure 11 - Looping Extension Cord over Cord
Hitch
www.desatech.com |
10 |
113005 |
OPERATING CHAIN SAW
Continued
CUTTING WITH THE CHAIN SAW
1.Connect saw to extension cord. Connect extension cord to power supply.
2.Make sure section of log to be cut is not laying on ground. This will keep chain from touching ground as it cuts through log. Touching ground with moving chain will dull chain.
3.Use both hands to grip saw.Always use left hand to grip front handle and right hand to grip rear handle. Use firm grip. Thumbs and fingers must wrap around saw handles (see Figure 12).
4.Make sure your footing is firm. Keep feet apart. Divide your weight evenly on both feet.
5.When ready to make a cut, push the lockout button completely forward with the right thumb andsqueezethetrigger(seeFigure12).Thiswill turn saw on. Releasing trigger will turn saw off. Make sure saw is running at full speed before starting a cut.
6.When starting a cut, place moving chain against wood. Hold saw firmly in place to avoid possible bouncing or skating (sideways movement) of saw.
7.Guide saw using light pressure. Do not force saw. The motor will overload and can burn out. It will do the job better and safer at the rate for which it was intended.
8.Remove saw from a cut with saw running at full speed. Stop saw by releasing trigger. Make sure chain has stopped before setting saw down.
9.Practice until you can maintain a steady, even cutting rate.
Switch Lockout Button
Trigger
Figure 12 - Lockout Button andTrigger Location
FELLING A TREE (Cutting Down a
Tree)
WARNING:
•Avoidkickback.Kickbackcanresultinsevereinjuryordeath.SeeKickback,pages 4 and 5, to avoid risk of kickback.
•Do not fell a tree without ample skill or expert help.
•Keepchildren,animals,andbystanders away from area when felling a tree.
•If two or more persons perform bucking and felling operations at the same time, provide ample distance between operations.Providedistanceofatleast twice the height of tree being felled.
WARNING: When felling a tree, be aware of your surroundings. Do not endanger anyperson,strikeutility lines, orcausepropertydamage.Iftreestrikes utility lines, contact utility company at once.
Felling is the process of cutting down a tree. Make sure your footing is firm. Keep feet apart. Divide your weight evenly on both feet. Follow directions below to fell a tree.
Before Felling a Tree
1.Before felling, inspect tree. Make sure there are no dead limbs or branches that may fall on you. Study natural lean of tree, location of larger branches, and wind direction.This will help you judge which way tree will fall.
2.Clear work area around tree.
3.Plan and clear aretreat path before felling. Make retreat path opposite to planned direction of fall of tree and at 45° angle (see Figure 13).
Retreat Path
Direction of Fall
45° |
Tree |
Retreat Path
Figure 13 - Retreat Path FromTree
Continued
ENGLISH
113005 |
11 |
www.desatech.com |
OPERATING CHAIN SAW
Continued
4.Removedirt,stones,loosebark,nails,staples,and wire from tree where you will make felling cuts.
5.Stay on uphill side when felling tree. Tree could roll or slide downhill after falling.
Felling Procedure
A) Felling Notch
Aproperlyplacedfellingnotchwilldeterminedirectiontreewillfall.Placefellingnotchonsideoftreein directionyouwanttreetofall(seeFigure14).Follow directions below to create a felling notch.
1.Make lower notch cut as close to ground as possible. Hold saw so guide bar is horizontal. Cut 1/3 the diameter of tree trunk (see Figure 14). Note:Always make this horizontal lower notch cut first. If you make this cut second, tree can pinch chain or guide bar.
2.Start upper notch cut the same distance above first cut as first cut is deep.
Example: If lower notch cut is eight inches deep, start upper notch cut eight inches above it. Cut downwardat45°angle.Theuppernotchcutshould meet end of lower notch cut (see Figure 14).
3.Remove tree trunk wedge created by notching cuts.
B) Felling Cut
1.Make felling cut two inches higher than lower notch cut and on opposite side of tree (see Figure 14). Keep felling cut parallel to lower notch cut.
2.Cut towards notch.
WARNING: Do not cut all the way through tree. Leave about two inches of tree diameter uncut directly behind felling notch (see Figure 14).This uncut portion acts as a hinge.The hinge helps keep tree from twisting and falling in wrong direction.
|
|
Direction |
3rd Cut - |
Hinge |
of Fall |
|
||
Felling Cut |
|
|
|
|
|
2" |
|
2nd Cut - |
(5 cm) |
|
Upper Notch Cut |
|
|
1st Cut - |
|
|
Lower Notch Cut |
2"(5 cm) |
|
|
3.As felling cut nears hinge, tree should begin to fall. Note: If needed, drive wedges into felling cut to control direction of fall. If tree settles back and pinches chain, drive wedges into felling cut to removesaw.Onlyusewedgesmadeofwood,plastic, oraluminum.Neverusewedgemadeofsteel.This could cause kickback and damage to chain.
4.When tree begins to fall, quickly
•remove saw from felling cut
•release trigger to turn saw off
•put saw down
•exit area using retreat path
WARNING: Be alert for falling overhead limbs. Watch your footing while exiting area.
LIMBING A TREE
WARNING:Avoidkickback.Kickback can result in severe injury or death. See Kickback, pages 4 and 5, to avoid risk of kickback.
WARNING: When cutting limb that is under tension, use extreme caution. Be alert for wood springing back.When wood tension is released, limb could spring back and strike operator causing severe injury or death.
Limbing is removing branches from a fallen tree. Make sure your footing is firm. Keep feet apart. Divide your weight evenly on both feet. Do not remove larger limbs under tree that support log off ground. Remove each limb with one cut (see Figure 15). Clear cut limbs from work area often. This will help maintain a safe work area.
Make sure you start your cut where limb will not pinchsawduringcutting.Toavoidpinching,startcut onfreelyhanginglimbsfromabovelimb.Startcuton limbsundertensionfromunderlimb.Ifpinchoccurs, turn saw off, lift limb, and remove saw.
Figure 14 - Felling ATree
Figure 15 - Limbing ATree
www.desatech.com |
12 |
113005 |
OPERATING CHAIN SAW
Continued
BUCKING A LOG
WARNING:Avoidkickback.Kickback can result in severe injury or death. See Kickback, pages 4 and 5, to avoid risk of kickback.
WARNING:
•If on slope, make sure log will not roll down hill.Securelog byusingwooden stakes. Drive wooden stakes into ground on downhill side of log. Stand on uphill side of log while cutting.Log may roll after cutting.
•Never try cutting through two logs at sametime.Thiscouldincreasetherisk of kickback.
•While cutting log, never hold log with your hand, leg, or foot.
•While cutting log, never allow another person to hold log.
•Turnoffandunplugsawbeforemoving from one place to another.
Bucking a log is cutting a log into sections. Make sureyourfootingisfirm.Keepfeetapart.Divideyour weight evenly on both feet.When possible, raise log or section off ground. Do this by using limbs, logs, chocks, etc.
Whencuttingthroughlog,maintaincontrolbyreducingcuttingpressurenearendofcut.Donotrelaxyour grip on chain saw handles. Do not let moving chain touch ground. Ground will dull moving chain.After cutting through log, release trigger to turn saw off before moving saw.
Follow directions below to buck a log.
Entire Length Of Log On Ground
Cut log from top (see Figure 16).
Figure 16 - Bucking Log With Entire Length
On Ground
Log Supported On One End
1. |
Make first cut on underside of log (see Figure |
|
|
17). Use top of guide bar to make this cut. Cut |
|
|
1/3 through diameter of log. This cut will keep |
|
|
section from splintering when cut. |
|
2. |
Make second cut directly above first cut. Cut |
|
|
down to meet first cut. This cut will keep log |
ENGLISH |
|
from pinching guide bar and chain. |
|
|
|
|
Log Supported On Both Ends |
|
|
1. |
Make first cut from above log (see Figure 18). |
|
|
Cut 1/3 through diameter of log. This cut will |
|
|
keep section from splintering when cut. |
|
2. |
Make second cut on underside of log, directly |
|
|
under first cut. Use top of guide bar to make this |
|
cut. Cut up to meet first cut. This will keep log from pinching guide bar and chain.
TRIMMING A TREE (Pruning)
WARNING:Avoidkickback.Kickback can result in severe injury or death. See Kickback, pages 4 and 5, to avoid risk of kickback.
2nd Cut
1st Cut
Figure17-BuckingLogWhenLogIsSupported
On One End
1st Cut
2nd Cut
Figure18-BuckingLogWhenLogIsSupported
On Both Ends
Continued
113005 |
13 |
www.desatech.com |
OPERATING CHAIN SAW
Continued
WARNING: Do not operate chain saw while
•in a tree
•on a ladder or any other unstable surface
•in any awkward position
You may lose control of saw causing severe injury.
WARNING: Do not cut limbs higher than your shoulders.
CAUTION: Seek professional help if facing conditions beyond your ability.
Trimming a tree is the process of cutting limbs from a living tree. Make sure your footing is firm. Keep feet apart. Divide your weight evenly on both feet. Follow directions below to trim a tree.
1.Make first cut six inches from tree trunk on underside of limb. Use top of guide bar to make this cut. Cut 1/3 through diameter of limb (see Figure 19).
2.Move two to four inches farther out on limb. Make second cut from above limb. Continue cut until you cut limb off.
3.Make third cut as close to tree trunk as possible onunderside of limb stub.Usetop of guide barto make this cut. Cut 1/3 through diameter of stub.
4.Makefourthcutdirectlyabovethirdcut.Cutdown to meet third cut. This will remove limb stub.
2nd Cut - Pruning Cut (to avoid pinching)
4th Cut - Final Stub Cut
6" (15 cm)
2" to 4" (5 a 10 cm)
1st Cut - Pruning Undercut (to avoid splintering)
3rd Cut - Stub Undercut (to avoid splintering)
Figure 19 - Cutting A Limb
www.desatech.com |
14 |
113005 |
CLEANING AND
MAINTENANCE
NOTICE: Below are instructions for servicingyourchainsaw.Anyservicingnot mentioned below should be done by an authorized service center.
CLEANING SAW BODY
WARNING: Unplug chain saw from powersourcebeforeservicing.Severeinjury or death could occur from electrical shock or body contact with moving chain.
WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain.
WARNING:When cleaning saw body,
•do not submerge saw in any liquids
•do not use products that contain ammonia, chlorine, or abrasives
•do not use chlorinated cleaning solvents,carbon tetrachloride,kerosene, or gasoline
Keepsawbodyclean.Useasoftclothdampenedwitha mild soap and water mixture. Wipe saw body to clean.
CARE OF GUIDE BAR
Uneven bar wear causes most guide bar problems. Incorrect sharpening of chain cutter and depth gauge settings often cause this. When bar wears unevenly, it widens guide bar groove (see Figure 20). This causes chain clatter and rivet popping. Saw will not cut straight. Replace guide bar if this occurs.
Inspect guide bar before sharpening chain. A worn or damagedguidebarisunsafe.Awornordamagedguide bar will damage chain. It will also make cutting harder.
Guide Bar Groove
Guide Bar
Normal Guide |
Guide Bar With |
Bar |
Uneven Wear |
Figure 20 - Guide Bar Cross Section Showing
Uneven Bar Wear
Normal Guide Bar Maintenance
1. |
Remove guide bar from chain saw. |
|
2. |
Remove sawdust from guide bar groove periodi- |
|
|
cally. Use putty knife or wire (see Figure 21). |
|
3. |
Clean oil slots after each day of use. |
|
4. |
Remove burrs from sides of guide bar. Use flat |
|
|
file to make side edges square. |
ENGLISH |
Replace guide bar when
• bar is bent or cracked
• inside groove of bar is badly worn
Note: When replacing guide bar, see Replacement Parts and Accessories, page 17, for proper bar.
SHARPENING SAW CHAIN
WARNING: Unplug chain saw from powersourcebeforeservicing.Severeinjury or death could occur from electrical shock or body contact with moving chain.
WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain.
Keep chain sharp.Your saw will cut faster and more safely.A dull chain will cause undue sprocket, guide bar, chain, and motor wear. If you must force chain into wood and cutting creates only sawdust with few large chips, chain is dull.
Burr
Flat File
Guide Bar
Cleaning Groove With Putty Knife
Oil Slot
Figure 21 - Guide Bar Maintenance
Continued
113005 |
15 |
www.desatech.com |
CLEANING AND
MAINTENANCE
Continued
Items Needed to Sharpen Chain
Purchase these items from your local dealer, hardware store, or chain saw supplies outlet.
•5/32" round file
•Depth gauge tool
•File guide
•Vise
•Medium sized flat file
Sharpening Cutters
Use file guide for 30° filing.
1.Adjust chain for proper tension (see Saw Chain Tension Adjustment, pages 8 and 9).
2.Clampguidebarinvisetoholdsawsteady. Note: Do not clamp chain.
3.Press 5/32" round file (attached to file guide) into groove between top plate and depth gauge on chain. File guide should rest on both top plate and depth gauge (see Figure 22). Note: File at midpoint of guide bar.
Filing Direction
30° Guide Mark
File Guide
FILE
5/32" Round
File
HOLDER
Note:This illustration shows file guide placement and filing direction for sharpening cutters on left side of chain.
Figure 22 - File and File Guide Placement On Chain
Depth Gauge (right Depth Gauge (left side of chain) side of chain)
Groove
Groove
Top Plate (left
side of chain) Top Plate
(right side of chain)
4.Hold file guide level. Make sure 30° mark on file guide is parallel to center of guide bar (see Figure 22). This will insure that you file cutters at 30° angle.
5.File from inside towards outside of cutter until sharp. Only file in this one direction (see Figure 22). Note: Two or three strokes with file should sharpen cutter.
6.After each cutter is sharpened, move chain forward to sharpen next cutter. File all cutters on one side of chain.
7.Move to other side of chain and repeat process.
Filing Cutter Depth Gauges
Thecutterdepthgaugeclearanceisreducedascutters are sharpened. After every second or third sharpening, reset cutter depth gauges.
1.Place depth gauge tool (.025") firmly across top oftwocutters.Makesuredepthgaugeentersslot in depth gauge tool (see Figure 24).
2.Use medium flat file. File depth gauge level with depth gauge tool.
3.Remove depth gauge tool. With flat file, round off front corner ofcutter depth gauge (seeFigure 25).
After several hand filings, have authorized service center or sharpening service machine sharpen chain. This will insure even filing.
REPLACING SAW CHAIN
Replace chain when cutters are too worn to sharpen or whenchainbreaks.Onlyusereplacementchainnotedin this manual. Always include new drive sprocket when replacing chain. This will maintain proper driving of chain.Note:For properchainand drive sprocket, see
Replacement Parts and Accessories, page 17.
Flat File
Depth
Gauge
Depth Gauge Tool
Depth Gauge Slot
Figure 24 - Depth GaugeTool On Chain
Front Corner
.025"
.635 mm
Right Side of Chain |
Figure 25 - Round Off Front Corner Of Depth |
Figure 23 - Chain Part Locations |
Gauge |
www.desatech.com |
16 |
113005 |
STORAGE
Ifstoringsawformorethan30days,followstepsbelow.
1.Drain oil tank after each use.
2.Remove and clean guide bar and chain. Clean guide bar and chain by soaking in petroleum based solvent or mild soap and water mixture.
3.Dry guide bar and chain.
4.Place chain in container filled with oil. This will prevent rust.
5.Wipeathincoatingofoiloversurfaceofguidebar.
6.Wipeoffoutsideofsawbody.Dothiswithsoftcloth dampened with a mild soap and water mixture.
7.Store chain saw
•in a high or locked place, out of children’s reach
•in a dry place
•inacarryingcaseorwithscabbardoverguidebar
TECHNICAL SERVICE
You may have further questions about assembling, operating, or maintaining this product. If so, you can visit our Technical Service web site at www. desatech.com or contact our Technical Service Department at 1-800-858-8501 (English Only).You may also write to:
DESA Specialty Products™
ATTN: Technical Service Specialty Products P.O. Box 90004
Bowling Green, KY 42102-9004
When contacting DESA Specialty Products™, have ready
•Your Name
•Your Address
•Your Phone Number
•Model Number of Product
•Date of Purchase (Include copy of receipt for written requests).
REPLACEMENT PARTS AND ACCESSORIES
WARNING:Useonlyreplacementparts andaccessoriesdescribedinthismanual. Use of other parts or accessories could damage saw or injure operator.
For original replacement parts and accessories, contact your nearest Authorized Dealer or Authorized Service Center for this product. If they can not supply the part or accessory, contact your nearest Parts Central listed on page 65. Each Authorized Dealer, Authorized Service Center, and Parts Central is independently owned and operated.
See pages 62 through 64 for an Illustrated Parts List. If you need additional referral information, contact our Technical Service Department (see TechnicalService). In Canada call 1-800-561-3372 for parts information.
REPAIR SERVICE
Note:Only use original replacement parts.This will protect your warranty coverage for parts replaced under warranty.
Each Authorized Service Center is independently owned and operated.
WARRANTY SERVICE
Ifproductrequireswarrantyservice,returnittonearest Authorized Service Center. You must show proof of purchase. If faulty materials or workmanship caused damage, we will repair or replace product without charge.Note:Normalwear,misuse,abuse,neglect,or accidental damage is not covered under warranty.
NON-WARRANTY SERVICE
Ifproductrequiresservice,returnittonearestAuthorized Service Center. Repairs will be billed to you at regular repair list prices.
For additional Service Center or warranty information, call 1-800-858-8501 or visit our Technical Service web site at www.desatech.com.
ENGLISH
113005 |
17 |
www.desatech.com |
TROUBLESHOOTING
Note: For additional help, visit DESA Power Tools’™ technical service web site at www. desatech.com.
WARNING: Unplug chain saw from powersourcebeforeservicing.Severeinjury or death could occur from electrical shock or body contact with moving chain.
OBSERVED FAULT |
POSSIBLE CAUSE |
REMEDY |
|||
|
|
|
|
||
Saw runs, but does not cut |
Chain assembled backwards on |
See Assembly, pages 7 and 8 |
|||
|
guide bar |
|
|
|
|
|
|
|
|||
Saw does not cut unless heavily |
Chain is dull |
See Sharpening Saw Chain, pages |
|
||
forced. Cutting produces only saw- |
|
|
15 and 16 |
||
dust with few large chips |
|
|
|
|
|
|
|
|
|
||
Saw runs slow. Saw stalls easily |
Low power supply voltage |
Extension cord wire size too small. |
|||
|
|
|
See Extension Cords, page 10 |
||
|
|
|
|
|
|
Motor of saw does not run when you |
1. |
Switch lockout not pushed for- |
1. |
Push switch lockout forward |
|
squeeze trigger |
|
ward in to release trigger |
|
before squeezing trigger |
|
|
2. |
Extension cord connections loose |
2. |
Check cord connections |
|
|
3. |
Open line fuse or circuit breaker |
3. |
Check line fuse or circuit breaker |
|
|
4. |
Worn out motor brushes |
4. |
See authorized service center |
|
|
5. |
Open wiring circuit on saw |
5. |
See authorized service center |
|
|
|
|
|
||
Motor of saw runs, but chain does |
Gear train failure |
See authorized service center |
|||
not move |
|
|
|
|
|
|
|
|
|
|
|
Chain does not get oil |
1. |
Clogged oil slot in guide bar |
1. |
Remove guide bar and clean oil |
|
|
|
|
|
slot |
|
|
2. |
Oil is too thick |
2. |
Use correct weight of oil. See |
|
|
|
|
|
Filling Oil Tank, page 9 |
|
|
|
|
|
|
|
Chain comes off guide bar |
1. |
Chain is loose |
1. |
Tightenchain.SeeSawChainTen- |
|
|
|
|
|
sion Adjustment, pages 8 and 9 |
|
|
2. |
Guide bar and chain not as- |
2. |
See Assembly, pages 7 and 8 |
|
|
|
sembled correctly |
|
|
|
|
|
|
|
||
Saw smokes |
Saw damaged. Do not use saw |
See authorized service center |
|||
|
|
|
|
||
Saw leaks oil |
Oil cap is not secure |
Tighten oil cap. Note: Empty oil |
|||
|
|
|
tank when not in use. |
www.desatech.com |
18 |
113005 |
WARRANTY INFORMATION
Model _______________________________
Date Purchased ______________________
ELECTRIC CHAIN SAW LIMITED WARRANTY
Always specify model and serial numbers when writing the factory.
We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written warranty. We make no other warranty, expressed or implied.
DESA Specialty Products™ warrants this electric chain saw and any parts thereof, to be free from defects in material and workmanship for one year (90 days for reconditioned unit) from the date of first purchase from an authorized dealer, provided that the product has been properly maintained and operated in accordance with all applicable instructions. The bill of sales or proof of purchase must be presented at the time a claim is made under this warranty.
This warranty is extended only to the original retail purchaser. This warranty covers only the parts and labor required to restore this chain saw to its proper operating condition. Warranty parts must be obtained through factory authorized dealers and service centers for this product. These dealers and service centers will provide original factory replacement parts. Failure to use original factory replacement parts voids this warranty.
This warranty does not cover commercial, industrial, or rental usage, nor does it apply to parts that are not in original condition because of normal wear and tear, or parts that fail or become damaged as a result of misuse, accident, lack ofpropermaintenance,tampering,oralteration.Travel,handling,transportation,andincidentalcostsassociatedwith warranty repairs are not reimbursable under this warranty and are the responsibility of the owner.
Tothefullextentallowedbythelawofthejurisdictionthatgovernsthesaleoftheproduct,thisexpresswarrantyexcludes anyandallotherexpressedwarrantiesandlimitsthedurationofanyandallimpliedwarranties,includingwarrantiesof merchantabilityand fitness fora particular purpose to oneyearfrom the date of first purchase, and DESA Specialty Products’™ liability is hereby limited to the purchase price of the product and DESA Specialty Products™ shall not be liable for any other damages whatsoever including indirect, incidental, or consequential damages.
Some states do not allow limitation of how long an implied warranty lasts or an exclusion or limitation of incidental or consequential damages, so the above limitation of damages may not apply to you.
This warranty provides the original purchaser with specific rights. For information regarding those rights, please consult the applicable state laws.
ENGLISH
|
Industries of Canada, Inc. |
|
2220 Argentia Road |
|
Unit #4 |
Bowling Green, KY 42102-9004 |
Mississauga, Ontario |
L5N 2K7 |
|
800-858-8501 (English Only) |
905-826-8010 |
www.desatech.com |
FAX 905-826-8236 |
|
www.desatech.com |
113005 |
19 |
www.desatech.com |
®
SIERRA ELÉCTRICA
MANUAL PARA EL USUARIO
MODELOS: M12510US, M15012US, M15014US, M15014AS, M30016US,
M30016AS, M30016AW, M35016UW, M35016AW
IMPORTANTE:Leacuidadosamenteestemanualantesdearmar uoperarestasierraeléctrica.Elusoindebidodelamismapuede provocargraveslesiones.Guardeestemanualparaconsultarlo cuando lo necesite.
www.desatech.com |
20 |
113005 |
El Contenido |
|
INFORMACIÓN IMPORTANTE DE SEGURIDAD............................................................ |
22 |
Antes de utilizar la sierra................................................................................................................. |
22 |
Al utilizar la sierra............................................................................................................................ |
22 |
Contragolpes................................................................................................................................... |
23 |
Mantenimiento y almacenamiento de su sierra eléctrica ................................................................ |
24 |
IDENTIFICACIÓN DEL PRODUCTO................................................................................ |
25 |
DESEMBALAJE ............................................................................................................... |
25 |
TERMINOLOGÍA............................................................................................................... |
26 |
ENSAMBLAJE.................................................................................................................. |
27 |
AJUSTE DE TENSIÓN DE LA CADENA SERRADA....................................................... |
28 |
USO DE LA SIERRA ELÉCTRICA................................................................................... |
29 |
Lubricación...................................................................................................................................... |
29 |
Lubricación de la cadena ................................................................................................................ |
29 |
REMOCIÓN DE RESTOS DE LA TAPA DE LA RUEDA DENTADA................................................ |
30 |
Cables de prolongación................................................................................................................... |
30 |
Realización de cortes...................................................................................................................... |
31 |
Tala de un árbol (Derribamiento de un árbol).................................................................................. |
31 |
Desmembramiento de un árbol....................................................................................................... |
33 |
Trozado de un tronco....................................................................................................................... |
33 |
Poda de un árbol ............................................................................................................................. |
34 |
LIMPIEZAY MANTENIMIENTO........................................................................................ |
35 |
Limpieza del cabezal....................................................................................................................... |
35 |
Cuidado de la barra de guía............................................................................................................ |
35 |
Afilado de la cadena........................................................................................................................ |
36 |
Recambio de la cadena serrada...................................................................................................... |
37 |
ALMACENAMIENTO ........................................................................................................ |
38 |
SERVICIO TÉCNICO......................................................................................................... |
38 |
ACCESORIOSY PIEZAS DE REPUESTO....................................................................... |
38 |
SERVICIO DE REPARACIÓN........................................................................................... |
38 |
Servicio con garantía....................................................................................................................... |
38 |
Servicio sin garantía........................................................................................................................ |
38 |
DIAGNÓSTICOY RESOLUCIÓN DE PROBLEMAS ....................................................... |
39 |
INFORMACIÓN DE GARANTÍA....................................................................................... |
40 |
ILLUSTRATED PARTS BREAKDOWN/DESGLOSE ILUSTRADO DE PARTES/SCHÉMA |
|
DES PIÈCES..................................................................................................................... |
62 |
PARTS CENTRAL/CENTRAL DE PIEZAS/DÉPÔT DE PIÈCES..................................... |
65 |
ESPAÑOL
113005 |
21 |
www.desatech.com |