Page 1
© 2000 RadioShack Corporation.
All Rights Reserved.
RadioShack and RadioShack.com are trademarks
used by RadioShack Corporation.
OWNER’S MANUAL — Please read before using this equipment.
900 MHz Cordless Telephone
with 10 Memory Speed Dial
FEATURES
Your RadioShack 900 MHz Cordless Phone offers the latest advances in cordless phone technology. Its headset j ack lets you
connect an optional headset for hands-free convenience while
you use the phone. The base’s space-saving design makes it perfect for areas where space is limited.
Your phone has these features:
Ample Talk and Standby Time
— when fully charged (about 12
hours), the supplied battery provides about 7 hours of talk time or
7 days of standby time.
Security Access-Protection Code
— prevents other cordless
phone users from using your phone line while the keypad is off the
base.
10-Memory Speed Dial
— stores up to 10 frequently called
phone numbers for easy dialing.
10-Channel Auto Scan
— automatically selects a clear channel
when you make or answer a call.
Hearing-Aid Compatibility
— lets you use your phone with hear-
ing aids that have a T (telephone) switch.
43-3505.fm Page 1 Monday, August 7, 2000 4:58 PM
Page 2
2
Headset Jack
— lets you connect an optional headset (available
at your local RadioShack store) for hands-free convenience.
Volume Control
— lets you control the volume of the sound you
hear through the handset.
Page
— lets you send a paging signal from the base to the handset to help locate a misplaced handset or page someon e at the
handset.
Your phone is ETL listed to UL standards and meets all applicable
FCC standards.
WARNING:
To reduce the risk of fire or shock hazard, do not ex-
pose this product to rain or moisture.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER OR BACK. NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
This symbol is intended to alert you to the presence of uninsulated dangerous voltage within the
product’s enclosure that might be of sufficient
magnitude to constitute a risk of electric shock.
Do not open the product’s case.
!
43-3505.fm Page 2 Monday, August 7, 2000 4:58 PM
Page 3
3
READ THIS BEFORE INSTALLATION
Each device that you connect to the phone line draws po wer from
the phone line. We refer to this power draw as the device’s ringer
equivalence number, or REN. The REN is on the bottom of the
base.
If you are using more than one phone or other device on the line,
add up all the RENs. If the total is more than five (three in rural areas), your phone might not ring. If ringer operation is impaired, remove a device from the line.
FCC STATEMENT
This telephone complies with Part 68 of the
FCC Rules
. You must,
upon request, provide the FCC registration number and the REN
to your phone company. These numbers are on the bottom of the
base.
Compatible jacks for this phone are RJ11C and RJ11W, available
at your local RadioShack store.
Note:
You must not connect your phone to any of the following:
• coin-operated systems
• party-line systems
• most electronic key phone systems
This symbol is intended to inform you that important operating and maintenance instructions are
included in the literature accompanying this product.
!
43-3505.fm Page 3 Monday, August 7, 2000 4:58 PM
Page 4
4
THE FCC WANTS YOU TO KNOW
In the unlikely event that your phone causes problems on the
phone line, the phone company can temporarily discontinue your
service. If this happens, the phone company attempts to notify you
in advance. If advance notice is not practical, the phone company
notifies you as soon as possible and advises you of your right to
file a complaint with the FCC.
Also, the phone company can make changes to its lines, equipment, operations, or procedures that could affect the operation of
this telephone. The telephone company notifies you of these
changes in advances, so you can take the necessary steps to prevent interruption of your telephone service.
This equipment complies with the limits for a Class B digital device as specified in Part 15 of the
FCC Rules
. These limits provide
reasonable protection against radio and TV interference in a residential area. However, your equipment might cause TV or radi o
interference even when it is operating properly. To eliminate interference, you can try one or more of the following corrective measures:
• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and the radi o
or TV.
• Use outlets on different electrical circuits for the equipment
and the radio or TV.
Consult your local RadioShack store if the problem still exists.
43-3505.fm Page 4 Monday, August 7, 2000 4:58 PM
Page 5
5
LIGHTNING
You telephone has built-in lightning protection to reduce the risk of
damage from surges in telephone line and power line current. This
lightning protection meets or exceeds FCC requirement. However, lightning striking the telephone or power lines can damage
your telephone.
Lightning damage is not common. Nevertheless, if you live in an
area that has severe electrical storms, we suggest that you unplug
your phone when storms approach to reduce the possibility of
damage.
PREPARATION
Mounting the Phone
You can place the phone on a desk or table, mount it on a standard wall plate, or mount it directly on a wall.
Select a location that is:
• near an easily accessible AC outlet
• near a telephone line jack
• out of the way of normal activities
• away from electrical machinery, electrical appliances, metal
walls, filing cabinets, wireless intercoms, security alarms, and
room monitors
The base’s location affects the phone’s range. If you have a
choice of several locations, try each to see which provides the
best performance.
43-3505.fm Page 5 Monday, August 7, 2000 4:58 PM
Page 6
6
Caution:
The supplied AC adapter was designed specifically for
your phone. Use only the supplied adapter.
Notes:
• Your telephone connects directly to a modular telephone line
jack. If your phone line jack is not a modular jack, you can
update the wiring yourself, using jacks and adapters available
at your local RadioShack store. Or, you can let the phone
company update the wiring for you.
• The USOC number of the jack to be installed is RJ11C.
On a Desk
You can power the base using the supplied 12V, 200 mA AC/DC
adapter.
Cautions:
You must use a Class 2 power source that supplies
12V DC and delivers at least 200 mA. Its center tip
must be set to positive and its plug must fit the
phone's
DC 12V 200mA
jack. The supplied adapter meets
these specifications. Using an adapter that does not meet
these specifications could damage the phone or the adapter.
• Always connect the AC adapter to the phone before you connect it to AC power. When you finish, disconnect the adapter
from AC power before you disconnect it from the phone.
!
43-3505.fm Page 6 Monday, August 7, 2000 4:58 PM
Page 7
7
Follow these steps to place the base on a desk or table using the
supplied bracket.
1. Insert the bracket’s tabs into the base’s upper tab slots as
shown, then press down on the bracket’s clips and insert
them into the clip slots.
2. Plug one end of the supplied modular cord into the
TEL LINE
jack on
the back of the base.
3. Plug the modular cord’s other end
into a modular phone line jack.
4. Insert the supplied AC adapter’s barrel plug into the
DC 12V
200mA
jack on the back of the base.
5. Route the adapter’s cord through the stra in relief slot on the
bracket.
6. Plug the adapter into a standard AC outlet.
7. Lift the base’s antenna to a vertical position.
On a Wall Plate or Wall
1. Insert the supplied bracket’s tabs into the base’s lower tab
slots, then press down on the bracket’s clips and insert them
into the clip slots.
2. Plug one end of the supplied short modul ar cord into the
TEL
LINE
jack on the back of the base.
3. Insert the supplied AC adapter’s barrel plug into the
DC 12V
200mA
jack on the back of the base.
TEL LINE
DC 12V
200mA Jack
43-3505.fm Page 7 Monday, August 7, 2000 4:58 PM
Page 8
8
4. Route the adapter’s cord through the narrow groove on the
bottom of the bracket.
5. Plug the modular cord into the wall plate jack, then align the
bracket’s keyhole slots with the wall plate studs and slide the
base downward to secure it.
6. Plug the adapter into a standard AC outlet.
7. Press and lift out the handset holder, turn it over and upside
down so its tabbed edge faces up, then slide it back down
into its slot.
8. Lift the base’s antenna to a vertical position.
Note:
To mount the phone directly on a wall, you need two screws
(not supplied) with heads that fit into the keyhole slots on the bottom of the base.
Follow the steps under “On a Wall Plate or Wall ” on Page 7, then
apply these additional instructions.
1. Drill two holes 3
15
/16 inches (100 mm) apart.
Then thread a screw into each hole, l etting the
heads extend about 5/16 inch (8 mm) from the
wall.
2. Plug one end of the supplied long modular
cord into the
TEL LINE
jack on the back of the
base.
315/16"
5
/16"
43-3505.fm Page 8 Monday, August 7, 2000 4:58 PM
Page 9
9
3. Align the keyhole slots with the mounting screws and slide
the base downward to secure it.
Connecting, Charging, and
Replacing the Battery Pack
The phone comes with a rechargeable nickel-cadmium battery
pack. You must connect the battery pack and charge it for at least
12 hours before you use the phone for the first time.
1. Press down and slide off the battery pack compartment cover.
2. Unfasten the retainer strap and lift the battery pack out of the
compartment.
3. Plug the battery pack’s connector into the socket in the compartment (the connector fits only one way), then replace the
battery pack and fasten the retainer strap.
43-3505.fm Page 9 Monday, August 7, 2000 4:58 PM
Page 10
10
4. Replace the cover.
To charge the battery pack, place the handset either faceup or
facedown on the base. The CHARGE/IN USE indicator lights.
Notes:
• Recharge the battery pack if the handset beeps and the IN
USE/LOW BATT indicator on the handset flashes while you
are using the phone, or if the IN USE/LOW BATT indicator
flashes when the phone is not in use.
• When you first use the phone after charging or recharging the
battery pack, the phone might not work. Return the keypad to
the base for about 5 seconds to reset the se curity accessprotection code.
• About once a month, fully discharge the battery pack by
keeping the phone off the base until the low battery warning
tone sounds. Otherwise, the battery pack loses its ability to
fully recharge.
• If the CHARGE/IN USE indicator does not light when you
place the handset on the base, be sure the battery pack and
AC adapter are correctly and securely connected. Also,
check the charging contacts on the handset and base. If the
contacts are dirty or tarnished, clean them with a pencil
eraser.
• If the battery pack becomes completely discharged or the
base loses power while the handset is away from it, place the
handset on the base for about 5 seconds to reset the security
access-protection code. If the handset loses power, leave it
on the base to charge the battery pack.
43-3505.fm Page 10 Monday, August 7, 2000 4:58 PM
Page 11
11
• If you are not going to use your phone for an extended period
of time, disconnect its battery pack. This helps increase the
battery pack’s life.
• When the handset is on the base, the CHARGE/IN USE/
MESSAGE indicator lights even when the battery pack is not
connected. If your phone does not work, be sure the battery
pack is properly connected.
The supplied battery pack should last about a year. If the battery
pack does not hold a charge for more than 2 hours after an overnight charge, replace it with a new 3.6-volt, 600 mAh battery pack
with a connector that fits the socket in the battery compartment.
You can order a replacement battery pack through your local RadioShack store.
Note:
To avoid losing numbers stored in memory, you must install
and begin charging the new battery pack within 2 minutes of removing the old one.
Warning:
Dispose of the old battery back promptly and properly.
Do not burn or bury it.
Cautions:
• Be careful not to short the battery pack by touching it with
conducting materials, such as rings, bracelets, and keys. The
battery pack or conductor might overheat and burn.
• Do not open or mutilate the battery pack.
If you have trouble replacing the battery pack, take the phone to
your local RadioShack store for assistance.
43-3505.fm Page 11 Monday, August 7, 2000 4:58 PM
Page 12
12
Important:
The EPA certified RBRC
®
Battery Recycling Seal on the nickel-cadmium (Ni-Cd) battery indicates RadioShack is voluntarily participating in an
industry program to collect and recycle these batteries at the end of their useful life, when taken out of
service in the United States or Canada. The RBRC program provides a convenient alternative to placing used Ni-Cd batteries into
the trash or the municipal waste stream, which may be illegal in
your area. Please call 1-800-THE-SHACK (1-800-843-7422) for
information on Ni-Cd battery recycling and disposal bans/restrictions in your area. RadioShack’s involvement in this progra m is
part of the company’s commitment to preserving our environment
and conserving our natural resources.
43-3505.fm Page 12 Monday, August 7, 2000 4:58 PM
Page 13
13
A Quick Look at the Handset
Headset Jack
Press VOLUME
8888
or
9999
to adjust the handset volume during a
call (see “Adjusting
the Handset’s Volume” on Page 16).
Use MEM to store
or recall names
and numbers in
memory (see
“Memory Dialing”
on Page 18).
Press MUTE to turn off
the handset microphone (see “Using
Mute” on Page 17).
Press FLASH to
use the phone’s
flash function (see
“Using Flash” on
Page 17).
Use RINGER OFF/ON
to turn the ringer on
or off (see “Using a
Headset” on
Page 15).
Use REDIAL/PAUSE to redial
the last number dialed see
(“Using Redial” on Page 16), or
enter a pause in a memory
number (see “Entering a Pause
in a Memory Number” on
Page 19).
Press CH to change the
phone’s channel (see
“Changing Channels”
on Page 16).
Press TONE/
∗
∗ ∗
∗
to use your
phone company’s special
tone services when you
are on a pulse line (see
“Using Tone Services on a
Pulse Line” on Page 17).
Use TALK to make,
answer, or end a call
(see “Making and
Receiving Calls” on
Page 15).
43-3505.fm Page 13 Monday, August 7, 2000 4:58 PM
Page 14
14
Setting the Ringer
OFF/ON RINGER
controls the handset ringer. To have the phone
ring when a call comes in, slide
RINGER
to ON. To turn the ringer
off, slide
RINGER
to
OFF
.
When
RINGER
is set to
OFF
, the phone does not ring, but you can
still make outgoing calls. If you hear an extension telephone ring,
you can answer the incoming call on this phone. The CHARGE/IN
USE indicator on the base and IN USE/LOW BATT on the handset indicator flash until you answer the call.
Setting the Dialing Mode
Set
TONE/PULSE
on the back of the base for the type of service
you have. If you are not sure which type you have, do this simple
test after charging the battery pack.
1. Set
TONE/PULSE
to
TONE
before
use.
2. Press
TALK
so the CHARGE/IN
USE indicator lights then listen
for a dial tone.
3. Press any number other than 0 and 1.
Note:
If your phone system requires that you dial an access
code (9, for example) before you dial an outside number, do
not press the access code either.
If the dial tone stops, you have touch-tone service. If the dial
tone continues, you have pulse service.
TONE/PULSE
43-3505.fm Page 14 Monday, August 7, 2000 4:58 PM
Page 15
15
4. If you have tone service, leave
TONE/PULSE
set to
TONE
. If
you have pulse service, set
TONE/PULSE
to
PULSE
.
5. To hang up, place the handset on the base or press
TALK
.
Using a Headset
You can make or answer calls with hands-free convenience using
an optional headset that has a
3
/32-inch (2.5mm) plug. Contact
your local RadioShack store for a suitable headset. To connect
the headset, insert the headset plug into the jack on the handset.
BASIC OPERATION
Making and Receiving Calls
To make a call, lift the handset from the base, then press
TALK
.
You hear a dial tone and the CHARGE/IN USE indicator on th e
base and the IN USE/LOW BATT indicator on the handset light.
Dial the number.
To answer a call, lift the handset from the base, then press
TALK
.
The CHARGE/IN USE indicator lights.
To end a call, place the handset on the base or press
TALK
.
Notes:
• When you press a button, a single tone indicates that the
phone has accepted the command. Three tones indicate that
you pressed a button in error or there is severe interference.
(See “Changing Channels” on Page 16).
43-3505.fm Page 15 Monday, August 7, 2000 4:58 PM
Page 16
16
• If interference is severe, the handset might lose communication with the base and the call might disconnect. If this happens, return the handset to the base for about 5 seconds to
reset the security access-protection code.
Adjusting the Handset’s Volume
To adjust the handset’s volume, repeatedly press
VOLUME
8888
or
9999
during a call until the sound level is comfortable. The volume
remains set even after you hang up.
Note:
The handset beeps 3 times when you reach the lowest or
highest volume level.
Changing Channels
Every time you press
TAL K
, the phone automatically selects a
clear channel it uses for communication between the handset and
the base. If you hear interference during a call, repeatedly press
CH
to change the channel until you get a clear one.
Using Redial
To redial the last number dialed, press
TALK
then
REDIAL/PAUSE
.
You can also redial a busy number quickly without hanging up the
phone. Press
REDIAL.
You hear a dial tone then the phone auto-
matically redials the number.
Notes:
• The redial memory holds up to 32 digits, so you can redial
long-distance as well as local numbers.
43-3505.fm Page 16 Monday, August 7, 2000 4:58 PM
Page 17
17
• The redial memory can also store tone and pause entries
(see “Using Tone Services on a Pulse Line” and “Entering a
Pause in a Memory Number” on Page 19).
Using Mute
To talk to someone else in the room without the person on the other end of the phone line hearing your conversa tion, press
MUTE
.
Press
MUTE
again to resume your phone conversation.
Using Flash
FLASH
provides the electronic equivalent of a switchhook signa l
for special phone service such as Call Waiting.
For example, if you have Call Waiting, press
FLASH
to answer an
incoming call without disconnecting the current call. Press
FLASH
again to return to the first call.
Note:
If you do not have any special phone services, pressing
FLASH
might disconnect your current call.
Using Tone Services on a Pulse Line
Some special services, such as bank-by-phone, require tone signals. If you have pulse service, you can still use these tone services by following these steps:
1. Dial the service’s main number.
2. When the service answers, press
TONE/
*
. Any additional
numbers you dial are sent as tone signals.
3. After you complete the call, press
TALK
or return the handset
to the base. The phone automatically resets to pulse dialing.
43-3505.fm Page 17 Monday, August 7, 2000 4:58 PM
Page 18
18
Using Page
You can send a page to the handset to locate it when it is away
from the base and not in use. To page the hand set, press
PAGE
on the base. The handset rings for about 15 seconds. To find the
handset, press and hold
PAG E
. The handset rings for about 1
minute. Press any key on the handset or
PAGE
on the base to si-
lence it sooner.
MEMORY DIALING
You can store up to 10 numbers of 16 digits each in the phone’s
memory.
Notes:
• To keep your accounts secure, we recommend you do not
store your personal access code for services such as bankby-phone in a memory location.
• When storing numbers for special services (such as alternate
long-distance or bank-by-phone), store the service’s main
phone number in one memory location and numbers for additional information in other locations.
Storing a Number in Memory
1. Press
MEM
on the handset.
2. Dial the desired number (up to 16 digits including an y pause
entries).
3. Press
MEM
again to store the number.
43-3505.fm Page 18 Monday, August 7, 2000 4:58 PM
Page 19
19
4. Press the memory location number (
1–0
) you want to store.
The handset sounds two long beeps.
Note:
If you hear three short beeps, you did not store the
number successfully. Start again from step 1.
5. Write down the stored name and number on the memory
label provided.
Note:
• If the low battery warning tone sounds and the IN USE/LOW
BATT indicator flashes, recharge or replace the battery within
2 minutes, or the phone will not retain the numbers stored i n
memory.
• If you receive a call while you are storing a number in memory, press
TALK
to answer the call. After the call, begin again
at Step 1.
• To change a number stored in memory, simply store a new
number in that memory location.
Entering a Pause in a Memory Number
In some telephone systems, you must dial an access code (9, for
example) and wait for a second dial tone before yo u can dial an
outside number. You can store the access code with the phone
number. However, if you do, you should also store a pause after
the access code to allow the outside line time to connect. After entering the access code, press
REDIAL/PAUSE
to enter a 2-second
pause.
43-3505.fm Page 19 Monday, August 7, 2000 4:58 PM
Page 20
20
Dialing a Stored Number
Press
TALK
. When you hear the dial tone, press
MEM
then the
memory location number (
1–0
). The phone dials the number.
Chain Dialing Service Numbers
To quickly recall special services numbers (such as alternate long
distance or bank by phone), store each group of numbers in its
own memory location.
When calling special services, dial the service’s main number first.
Then, at the appropriate place in call, press
MEM
, then the number
for the location where the additional numbers are stored.
Testing Stored Emergency Numbers
If you store an emergency service’s number (police department,
fire department, or ambulance, for example) and you want to test
the stored number, make the test call during the late evening or
early morning to avoid peak demand periods. Remain on the line
to explain the reason for your call.
43-3505.fm Page 20 Monday, August 7, 2000 4:58 PM
Page 21
21
TROUBLESHOOTING
We do not expect you have any problem with your telephone, but
if you do, these suggestions might help.
Problem Suggestion
The handset does not work. Move the handset closer to the base.
Raise the base’s antenna to a vertical
position.
Make sure the phone’s modular cord
and the AC adapter are correctly and
securely connected.
Make sure the handset’s battery pack
is properly connected and charged.
Recharge the handset’s battery pack.
Place the handset on the base for
about five seconds to reset the security access-protection code.
The call is noisy. Keep the handset and base away
from interference sources such as
computers, remote control toys, wireless alarm systems, wireless intercoms and room monitors, fluorescent
lights, and electrical appliances. If the
interference is severe, turn off the
device.
Move the handset closer to the base.
Hang up and redial the number.
Press CH to change the channel.
43-3505.fm Page 21 Monday, August 7, 2000 4:58 PM
Page 22
22
If you still have problems, disconnect the phone. If other phones
on the same line work properly, the fault is in this phone or its installation. If you cannot find the problem, take the p hone to your
local RadioShack store for assistance.
CARE
Keep the phone dry; if it gets wet, wipe it dry immediately. Use
and store the phone only in normal temperature environments.
Handle the phone carefully; do not drop it. Keep the phone away
from dust and dirt, and wipe it with a damp cloth occasionally to
keep it looking new.
Modifying or tampering with the phone’s internal components can
cause a malfunction and might invalidate its warranty and void
your FCC authorization to operate it. If your phone is not performing as it should, take it to your local RadioShack store for assistance. If the trouble is affecting the telephone lines, the phone
company can ask you to disconnect your phone until you have resolved the problem.
The range decreases. Make sure the base’s antenna is
raised and is not touching a metal surface.
Recharge the handset’s battery pack.
You can receive calls, but
cannot make call.
Set
TONE/PULSE
correctly for the
type of service you have (see “Setting
the Dialing Mode” on Page 14).
Problem Suggestion
43-3505.fm Page 22 Monday, August 7, 2000 4:58 PM
Page 23
23
NOTES
43-3505.fm Page 23 Monday, August 7, 2000 4:58 PM
Page 24
RadioShack Corporation
Fort Worth, Texas 76102
43-3505
086-002109-019
07A00
Printed in Hong Kong
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material
and workmanship under normal use for one (1) year from the date of purchase from
RadioShack company-owned stores and authorized RadioShack franchisees and
dealers. EXCEPT AS PROVIDED HEREIN, RadioShack MAKES NO EXPRESS
WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN
DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO
LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR
ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT OR
ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT
LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS OF
TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations
or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the
RadioShack sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, unless otherwise provided by law: (a) correct the defect by
product repair without charge for parts and labor; (b) replace the product with one of
the same or similar design; or (c) refund the purchase price. All replaced parts and
products, and products on which a refund is made, become the property of RadioShack. New or reconditioned parts and products may be used in the performance
of warranty service. Repaired or replaced parts and products are warranted for the remainder of the original warranty period. You will be charged for repair or replacement
of the product made after the expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of
God, abuse, accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or maintenance, alteration, lightning or other incidence of
excess voltage or current; (b) any repairs other than those provided by a RadioShack
Authorized Service Facility; (c) consumables such as fuses or batteries; (d) cosmetic
damage; (e) transportation, shipping or insurance costs; or (f) costs of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
RadioShack Customer Relations,
200 Taylor Street, 6th Floor, Fort Worth, TX 76102
We Service What We Sell
12/99
43-3505.fm Page 24 Monday, August 7, 2000 4:58 PM
Loading...