Radio Shack ACCURIAN 15-1938, ACCURIAN 15-1937, ACCURIAN 40-1462 User Manual

0 (0)
Radio Shack ACCURIAN 15-1938, ACCURIAN 15-1937, ACCURIAN 40-1462 User Manual

Networked Home

Entertainment System

All items shown below are sold separately. 15-1938 is required for the PowerLine system to work.

PowerLine Digital Audio Sender

Includes Sender and Power cord.

15-1938

PowerLine Amplified Receiver/ Speaker System

Includes Amplified Receiver/Speaker, Satellite Speaker, Speaker Wire, and Power cord.

40-1462

Thank you for buying the RadioShack Networked Home Entertainment System. Now you can send high-quality digital stereo audio to any room in your home that has an AC outlet, without running cable. This system uses the existing AC electrical wiring in your home to send digital signals.

1.Connect an audio source to your PowerLine sender and plug into any AC outlet.

CD Player

Signal

Receiver

 

Path

 

Line In

Speaker In

Connection

Connection

Power

Note: Do not use two senders in the same place.

2.Connect PowerLine speakers to any AC outlet in your home,

OR

VOLUME BASS

BALANCE TREBLE POWER

OR, Connect a PowerLine receiver to any AC outlet in your home, and then connect to it, either

A)...an audio source with speakers, or

B)...non-PowerLine speakers.

Simply plug the audio outputs of any component – such as an A/V receiver, CD, or MP3 player – into the audio inputs of the sender (#15-1938) and plug the sender into an AC outlet. Then, plug RadioShack PowerLine Digital Receiver/Speakers (# 40-1462) into any electrical outlet in your home. If you have your own speakers, just plug your RadioShack PowerLine Digital Audio Receiver/Amplifi er (# 15-1937) into any electrical outlet and connect your speakers. Using this receiver, you can control the volume, balance, bass and treble of your remote speakers. Best of all, the RadioShack Networked Home Entertainment System is completely portable.

1.

Make certain that your audio source is powered off.

SPEAKER IN

AUDIO IN AC IN

2.

Connect the line level stereo outputs from the audio source, such

Audio Input

 

as a CD player to the sender's AUDIO IN. Match LEFT to L and

 

Level Lo/Hi

 

RIGHT to R.

 

 

 

 

Or,

 

 

 

Connect the surround or speaker outputs from your Home Theater

 

 

 

System or A/V receiver to the sender's SPEAKER IN.

 

 

 

DO NOT connect both cables to the sender's AUDIO IN and

 

 

 

SPEAKER IN.

 

 

3.

Connect the AC power cord’s female plug end into AC IN, and

 

 

 

then plug the AC cord’s other end into a standard AC outlet.

 

 

4.

Turn on the audio source, and then press the POWER button on

 

 

 

your sender.

 

 

 

Your sender’s Audio Input Level Lo/Hi is preset to Lo. If you hear

Sender Rear View

 

volume distortion, adjust the Audio Input Level Lo/Hi to Hi.

1.Split apart about 4 inches (10.16 cm) of speaker wire on

SPEAKER OUT L R M S AC IN

 

 

each end. Then use a wire stripper to strip 1/2 in. (1.27 cm)

 

 

of insulation from each wire’s end.

 

 

2.Connect one end of the wire to SPEAKER OUT on the

 

 

Amplifi ed Receiver / Speaker. (Be sure to match the

 

 

polarity of the wires when making your connection.)

 

 

3. Connect the other end to the satellite speaker. Be sure to

 

 

correctly match polarity.

 

 

4. Insert the AC power cord’s female plug end into the

 

Sattelite Speaker’s Rear

receiver/speaker’s AC IN jack, and then plug the AC cord’s

 

other end into a standard AC outlet.

 

View

Speaker Settings

Amplifi ed Receiver / Speaker’s Rear View

The default setting for your amplifi ed speaker is stereo (S). If you connect two pairs of the 40-1462, you must set one to left (L) and one to right (R).

If you use a single Amplifi ed Receiver / Speaker, set LRMS to mono (M).

PowerLine Digital Audio Receiver/Amplifier

Includes Receiver/Amplifier and Power cord.

15-1937

Please read this user’s guide before installing, setting up and using your new product

www.radioshack.com

AB

OR

 

 

Speaker Out

LINE OUT SPEAKER OUT POWER

 

Line Out

 

1.Power off all system devices before making any connections.

2.Connect a matching set of speakers (8 ohms) to the Amplifi er / Receiver's SPEAKER OUT.

Or, connect stereo audio cables from the Amplifi er / Receiver's LINE

OUT to the line level inputs on your A/V receiver. (Match LEFT to L and

RIGHT to R).

3.Insert the AC power cord’s female plug end into the Amplifi er / Receiver's POWER jack, and then plug the AC cord’s other end into a standard AC outlet.

VOLUME

BALANCE

POWER

BASS TREBLE

Amplifi er / Receiver Rear View

Loading...
+ 1 hidden pages