Radio Shack 43-3871 User Manual

2.4 GHz Multi-Handset Expandable Cordless Telephone with Digital Answering System

43-3871

Memo Recording — lets you leave messages for yourself or others in your home or office, or record your phone conversations. (See “Voice memo” on page 61.)

Phone Pick-Up Detection — stops recording when you pick up any phone on the same line as the answering system, and resets to answer the next call.

Call Screening — lets you listen as a caller leaves a message. (See “Screening a Call” on page 57.)

Speakerphone — lets you conduct a hands-free conversation using the handset and base speaker. (See “Making and Receiving Calls” on Page 26)

Handset Remote Operation — lets you listen to your incoming messages from the handset. (See “Remote Operation” on page 62.)

Message Alert — beeps when you have new incoming message. (See “Setting the Message Alert” on 55.)

Convenient Extension Placement — lets you place accessory handsets (up to four total) anywhere you have an AC outlet, regardless of phone jack location.

Call Waiting/Caller ID — lets you answer a call even when you’re on the phone and see who’s calling before you answer.

! IMPORTANT !

If an icon appears at the end of a paragraph, go to the box on that page with the

corresponding icon for pertinent information.
o— Warning ! — Important		— Caution Ô — Note
	OWNER’S MANUAL	Please read before using this equipment.

© 2004 RadioShack Corporation.

All Rights Reserved.

RadioShack and RadioShack.com are trademarks used by RadioShack Corporation.

ENERGYSTAR and the ENERGYSTAR certification mark are registered US marks.

DirectLink is a registered trademark of Uniden Corporation.

CONTENTS

Introduction ...................................	3
Important Information ...................	4
FCC Statement ..................................	4
Surge Protection ................................	5
Important Safety Instructions ........	6
Important Caller ID Information ....	7
Read This Before Installation .............	7
Installation .....................................	8
Selecting a Location ..........................	8
Connecting/Charging the Battery
Pack ..............................................	10
Setting Menu Options .................	13
About the Menu Options ..................	13
Summary of Main Menu Options and
Submenu Option ...........................	13
Setting Up the Menu ........................	17
Making and Receiving Calls .......	26
Placing a Call on Hold .....................	27
Redialing a Call ................................	27
Adjusting the Handset Ringer,
Earpiece and Speaker Volume .....	29
Do Not Disturb (DND) ......................	29
Mute Microphone .............................	30
Tone Dialing Switch-over .................	30
Traveling Out-of-Range ....................	31
Clarity Booster .................................	31
Privacy Mode ...................................	31
3-Way Conferencing ........................	32
Flash and Call Waiting .....................	32
New Message LED ..........................	32
Phonebook ..................................	33
Storing Phone Numbers,
Names, Distinctive Rings, and
Speed Dial ....................................	33
Steps for Entering Names and
Special Characters ........................	34
Viewing the Phonebook ...................	36
Making Calls Using the
Phonebook ....................................	37
Speed Dialing ..................................	37
Editing or Erasing a Stored Name,
Phone Number, Distinctive Ring,
and Speed Dial .............................	38
Chain Dialing ...................................	39
Caller ID ......................................	39
Caller ID and CIDCW (Caller ID on
Call Waiting) ..................................	39
Viewing the Caller ID List .................	40
Deleting a Caller ID Message ..........	41
Using the Caller ID Message List ....	42
Call Waiting Deluxe Features ...........	43
Expanding Your Phone ...............	44
Register the Handset to the Base ....	44
Using the DirectLink Mode ...............	45

4-Way Conferencing ........................	46
Intercom/Call Transfer Feature ........	46
Replacing the Base .........................	48
The Integrated Answering
Device ........................................	48
Features ..........................................	49
Turning the Answering System
On/Off ...........................................	49
Setting up your Answering
System .........................................	50
Using your Answering System ........	58
Remote Operation ...........................	62
Installing The Beltclip .................	66
Using a Headset .........................	66
Troubleshooting ..........................	67
Care ............................................	69
Service and Repair .....................	69

2

INTRODUCTION

Thank you for purchasing a RadioShack 2.4 GHz Multi Handset Expandable Cordless Telephone. Unlike other conventional cordless telephones, your telephone supports up to four handsets on a single telephone line. You can add a handset to any room in your home or office that has an AC outlet. No more running to the other end of the house to answer the phone! You can transfer outside calls to other handsets. If you subscribe to Call Waiting with Caller ID, the phone shows you the incoming caller information, even when you are already talking on the phone.

Cordless phones require AC power to operate. When the power is off, you cannot make or receive calls by using your phone. You should also have a phone that does not need AC power to operate (not a cordless phone), so you can still make and receive calls if there is an AC power failure. !

The digital answering system stores up to 12 minutes of messages on a computer chip and records each message’s day and time. This gives you advanced capabilities over tape-based answering machines:

•You can delete individual messages and save the rest.

•There are no tapes to bother with and no tape mechanisms to wear out.

The remote operation feature lets you operate your answering system from a touch-tone phone (or from a rotary phone with a pocket tone dialer).

!IMPORTANT !

•When AC power is lost, the phone loses the digital security code connection between the base and the handset. When power is restored, put the handset on the base briefly to restore this connection so you can use the handset.

•Your phone operates on standard radio frequencies as allocated by the FCC.

•It is possible for other radio units operating nearby on similar frequencies to unintentionally intercept your conversation or cause interference. This possible lack of privacy can occur with any cordless phone.

Introduction

3

Information Important

As an ENERGYSTAR Partner, RadioShack Corporation has determined that this product meets the ENERGYSTAR guidelines for energy efficiency.

		IMPORTANT
		INFORMATION
		This telephone has been tested and found
		to comply with all applicable UL and FCC
		standards.
		FCC STATEMENT
		Your telephone compiles with Part 68 of the
		FCC Rules.Upon request, you must provide
		the phone’s FCC registration number and
		REN to your phone company. These
		numbers are on the base unit.
		Your phone is not intended to be used with
		party-line systems. Connection to party line
		service is subject to state tariffs. Contact the
		state public utility commission, public
		service commission, or corporation
		commission for information. Ô
		We have designed your phone to conform
		to federal regulations, and you can connect
	Ô NOTE Ô	it to most telephone lines. However, each
	You must not connect your	phone (and each device, such as a
		telephone or answering machine) that you
	phone to:
		connect to the telephone line draws power

•coin-operated systems from the telephone line. We refer to this

• most electronic key				power draw as the device’s ringer
telephone systems				equivalence number, or REN on the back of
				your phone.
WARNING: To reduce the risk of			CAUTION.				!			CAUTION: TO REDUCE THE RISK OF ELECTRIC
fire or shock hazard, do not expose										SHOCK, DO NOT REMOVE COVER OR BACK. NO USER-
this product to rain or moisture.			RISK OF ELECTRIC							SERVICEABLE PARTS INSIDE. REFER SERVICING TO
			SHOCK DO NOT OPEN							QUALIFIED PERSONNEL.
The lightning symbol is intended to alert you to the presence of								The exclamation symbol is intended to inform you that important operating
uninsulated dangerous voltage within this product’s enclosure that							!	and maintenance instructions are included in the literature accompanying
might be of sufficient magnitude to constitute a risk of electric shock.								this product.
Do not open the product’s case.

4

If you use more than one phone or other device on the line, add up all of the RENs. If the total is more than five (three in rural areas), your telephones might not ring. If ringer operation is impaired, remove a device from the line.

In the unlikely event that your phone causes problems on the phone line, the phone company can temporarily discontinue your service. If this happens, the phone company attempts to notify you in advance. If advance notice is not practical, the phone company notifies you as soon as possible and advises you of your right to file a complaint with the FCC.

Also, the phone company can make changes to its lines, equipment, operations, or procedures that could affect the operation of this phone. The telephone company notifies you of these changes in advance, so you can take the necessary steps to prevent interruption of your telephone service.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Privacy of communications, may not be ensured when using this phone.

SURGE PROTECTION

Your telephone has built-in protection circuits to reduce the risk of damage from surges in telephone line and power line current. These protection circuits meet or exceed the FCC requirements. However, lightning striking the telephone or power lines can damage your telephone.

Lightning damage is not common. Nevertheless, if you live in an area that has severe electrical storms, we suggest that you unplug your phone when storms approach to reduce the possibility of damage.

Important Information

5

IMPORTANT SAFETY INSTRUCTIONS

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:

1.Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink, or laundry tub, in a wet basement or near a swimming pool.

2.Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.

3.Do not use the telephone to report a gas leak in the vicinity of the leak.

4.Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions.

SAVE THESE INSTRUCTIONS

Instructions Safety Important

6

IMPORTANT CALLER ID INFORMATION

To use Caller ID and Call Waiting, you must be in an area where those services are available and you must subscribe to those services through your local phone company. Where Caller ID is offered, one or more options are generally available:

•caller’s number only

•caller’s name only

•caller’s name and number

If you subscribe to Call Waiting ID and Caller ID, the system can show you the incoming caller information, even when you are already talking on the phone.

READ THIS BEFORE INSTALLATION

We have designed your phone to conform to federal regulations and you can connect it to most phone lines. However, each device that you connect to the telephone line draws power from the line. We refer to this power draw as the phone’s ringer equivalence number, or REN. The REN is on the bottom of your phone.

If you use more than one phone or other device on the line, add up all the RENs. If the total is more than five (three in rural areas), your phones might not ring. If ringer operation is impaired, remove one of the devices from the line.

Important Caller ID Information

7

Installation

ÔNOTES Ô

•If your home has specially wired alarm equipment connected to the telephone line, be sure that installing the system does not disable your alarm equipment. If you have questions about what will disable alarm equipment, contact your telephone company or a qualified installer.

•The USOC number of the jack to be installed is RJ11C (or RJ11W for a wall plate jack).

INSTALLATION

Before using your phone, carefully peel the protective film off the display. The film protects the handset window during shipment and is not necessary for use.

SELECTING A LOCATION

You can place the phone’s base on a desk or table, or mount it on a standard wall plate or directly on a wall. Select a location that is:Ô

•near an accessible AC outlet

•near a telephone line jack

•out of the way of normal activities

•away from electrical machinery, electrical appliances, metal walls or filing cabinets, wireless intercoms, alarms, and room monitors

•away from other cordless phones

The base’s location affects the handset’s range. If you have a choice of several locations, try each to see which provides the best performance.

Your telephone connects directly to a modular telephone line jack. If your telephone wiring does not have a modular jack, you can update the wiring yourself using jacks and adapters (available at your local RadioShack store), or have the telephone company update the wiring for you. You must use compatible modular jacks that are compliant with Part 68 of FCC Rules. Ô

8

On a Desk Top

1. Plug one end of	TEL	DC IN 9V
the supplied long	LINE
modular cord into
the TEL LINE jack
on the back of
the base.

2. Plug the modular cord’s other end into a modular phone line jack.

3.Insert the supplied AC adapter’s barrel plug into the DC IN 9V jack on the back of the base.

4.Route the adapter’s cord through the strain relief slot on the base, then plug the adapter into a standard AC outlet.

5.Lift the base’s antenna to a vertical position.

On a Wall Plate or Wall

To mount the phone directly on a wall, you need two screws (not supplied) with heads that fit into the keyhole slots on the base.

Drill two holes 315/16 inches apart. Thread a screw into each hole, letting the heads extend about 1/8 inch.

1.Detach the bracket from the bottom of the base.

2.Insert the two

tabs at the top of the narrow end of

the supplied

bracket into the base’s upper tab slots, then press down on the bracket’s latches

and insert them into the lower slots.

CAUTION

You must use

!a Class 2 power source

that supplies 9V DC and delivers at least 400 mA. Its center tip must be set to positive and its plug must fit the phone’s DC IN 9V jack. The supplied adapter meets these specifications. Using an adapter that does not meet these specifications could damage the phone or the adapter.

Installation

9

Installation

3.Plug one end of the supplied modular cord (short for a wall plate, long for direct wall mounting) into the TEL LINE jack on the base’s back.

4.Insert the supplied AC adapter's barrel plug into the DC IN 9V jack.

5.Route the

adapter and modular cords through the base’s grooves.

6. For a wall plate, plug the modular

cord’s other end into the wall plate jack, then align the base’s keyhole slots with the wall plate studs and slide the base downward to secure it.

For direct wall

mounting, align the base’s

keyhole slots

with the mounting

screws and

slide the base downward to secure it.

7.Plug the adapter into a standard AC outlet.

8.Lift the base’s antenna to a vertical position.

CONNECTING/CHARGING THE BATTERY PACK

The phone comes with a rechargeable nickel-metal hydride (Ni-MH) battery pack in the handset, but not connected. Before using your phone, you must connect the battery pack, then charge it for about 15–20 hours.

10

1.Press down and slide off the battery compartment cover.

2.Lift the battery pack out of the compartment.

3.Plug the battery pack’s connector into the socket in the compartment (the connector fits only one way), then place the battery pack in the compartment.

4.Replace the cover.

To charge the battery pack, place the handset on the base. The CHARGE indicator on the base lights.

Recharge the battery pack when

Low Battery flashes on the display.

If you have trouble replacing the battery pack, take the phone to your local RadioShack for assistance.

Recharging the Battery Pack

•If the battery pack becomes weak during a call, Low Battery flashes. When this happens, you cannot make a call until you recharge the battery pack.!

•If the display is blank and the phone does not work, recharge the battery pack. (The battery power might be too low to light the display.)

•About once a month, fully discharge the battery by keeping the handset off the base until Low Battery flashes on the display. Otherwise, the battery pack loses its ability to fully recharge.

•Using a damp cloth, clean the charging contacts on the handset about once a month.

! IMPORTANT !

Be sure the battery pack is properly connected before you try to charge it. The CHARGE indicator lights when the handset is on the base, even if the battery pack is not connected.

Installation

11

oWARNING o

Dispose of the old battery pack promptly and properly. Do not burn or bury it. There is a risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.

Installation

•If you are not going to use your phone for an extended period, disconnect the battery pack. This increases the battery pack’s usable life.

•The supplied battery pack should last for about a year. If the battery pack does not hold a charge for more than 2 hours after an overnight charge, replace it with a new 3.6-volt, 800 mAh battery pack with a connector that fits the socket in the battery compartment. You can order a replacement battery pack through RadioShack. Install the

new battery pack and charge it for about 15–20 hours.o

12

SETTING MENU

OPTIONS

ABOUT THE MENU OPTIONS

There are 6 main menu setup options,

(DirectLink® Mode, Room Monitor, Handset Setup, Answ. Setup, Global Setup and

System Reset) and 20 submenu options. Ô

SUMMARY OF MAIN MENU

OPTIONS AND SUBMENU

OPTION

DirectLink Mode

DirectLink Mode allows a pair of handsets to work without the base unit for direct handset-to-handset communication, like a pair of walkie-talkie. Use them at sporting events or while shopping to stay in contact with family members or friends. You must set the two handsets to DirectLink Mode to utilize this feature.

Room Monitor

This feature allows you to monitor sounds in another room (see page 18 for setup). One handset or the base is placed in the desired room to monitor (acts as remote mic), and the other handset is placed near listener (remote speaker). This is useful for monitoring child activities.

Ô NOTE Ô

During Global Setup and System Reset, make sure your cordless phone is in standby mode (not in use), and all handsets are within range of the main base unit.

Setting Menu Options

13

Options Menu Setting

Handset Setup

The following submenu options must be set separately for each handset.

	Submenu option		Description
	Ringer Tones	Adjusting the ringer tone (see page 18).
	(Default is Flicker)
		Set the distinctive ring (tone your phone makes when
		ringing) (see page 19). “Distinctive Ringer” allows you to
		preset memory locations with a designated ring tone.
		When an incoming call is received and the Caller ID
		information matches the information in one of the memory
	Distinct. Ring	locations, the distinctive ring that has been stored for that
	(Default is on)	particular Caller will sound. If you have set multiple
		memory locations with distinctive rings, switching the
		setting to “Distinctive Off” will result in no distinctive
		ringing. All incoming calls will have a normal ring tone.
		Switching to “Distinctive On” will activate all programmed
		distinctive ring memory locations.
		Allows you to answer the phone without pressing
	AutoTalk	TALK/FLASH or SPEAKER. When the AutoTalk is set to
	(Default is off)	On, simply remove the handset from the cradle and the
		phone automatically answers the call (see page 19).
		Allows you to answer the phone without pressing
	Anykey Answer	TALK/FLASH or SPEAKER. When the Anykey Answer is
	(Default is off)	On, you can answer a call by pressing any number key,
			/tone/< or #/> on the handset (see page 20).
		Customize your handset(s) by giving it a banner name.
	Banner	The name will be displayed on the LCD screen during
		standby mode, Intercom, Transfer, Room Monitor and
	(True Banner)
		Copy Phonebook operation. The banner name will be
		displayed on the receiving handset as well (see page 20).
	Language	The menu display options can be set to English, French
	(Default is English)	or Spanish for easy setup use (see page 20).
	Key Touch Tone	Allows you to set your phone’s key touch-tone to On or
		Off (tone your keypad makes when keys are pressed)
	(Default is on)
		(see page 20).

14

Answering Setup

This main menu option allows you to set up TAD settings from your handset. You can also set these submenu options from the base (see page 52).

	Submenu option	Description
		Select a two-digit Personal Identification Number (PIN)
	Security Code	code. A PIN code is required to play your messages from
		a remote location, you will need to enter a two-digit PIN
		code (see page 21).
		Allows you to set the number of rings the caller hears
		before your answering system plays the outgoing
		message. You can set the ring time to answer after two,
	Ring Time	four, or six rings. Setting “TS” (Toll Saver), the answering
		system picks up after two rings if you have new
		messages, and after four rings if there are none (see
		page 21).
		Set the duration for recording the incoming messages.
		You have three record time options. The options “1
		minute” or “4 minutes” set the duration for recording the
	Record Time	incoming messages. “Announce only” answers the call
		with the preset greeting or your personal greeting but
		prevents the caller from leaving a message (see page
		21).
	Message Alert	Lets you know when you have a new incoming message
		by sounding a short alert tone (see page 22).
		Select the Language of your answering system
	Language	announcements from English, French, or Spanish (see
		page 22).
		Allows you to screen an incoming call before answer the
	Call Screen	call. Set the call-screening feature to On or Off (see page
		22).

Setting Menu Options

15

Options Menu Setting

Global Setup

If you change one of the Global settings, you change the setting for all additional handsets. Only one handset can change Global settings at a time.

	Submenu option	Description
	Day & time	Set the day and time of your display (see page 23).
		Set the Caller ID on Call Waiting (CIDCW) setting.
	CIDCW	CIDCW performs the same as regular Caller ID on a call
	(Default is CW on/	waiting number (see page 23). Call Waiting Deluxe allows
	CWDX off)	you to handle call waiting calls in seven different ways
		(see page 43).
		Store or edit the area code. If you enter a 3-digit area
		code number in the “Area Code” option, your local area
	Area Code	code does not appear in the Caller ID message. For calls
		received from outside your local area code, you will see a
		full 10-digit number (see page 23). Note: If your calling
		area requires 10-digit dialing, do not program this option.
		Set the dial mode to tone or pulse (see page 24). Most
	Dial Mode	phone systems use tone dialing, which sends DTMF tone
	(Default is tone)	through phone line, the default setting is tone dialing.
		Depends on your dialing system, set the dial mode.
	Copy Phonebook	Allow you to transfer the phonebook data stored in one
		handset to another handset (see page 24).

System Reset

System Reset is used to clear the handset's ID from the main base unit, or the base ID from the handset.

Submenu option	Description

Clear the handset ID from the base. Use this option, for De-register HS example, when you change the digital security code (see

page 25).

Clear the base ID. Use this option, for example, if you Replacing Base wish to deregister the base to use the handset with 43-

3570 (see page 25).

16

SETTING UP THE MENU

Entering the Menu

1.Press MENU/DEL in standby mode.

2.Use VOL/RING/ or VOL/RING/ to move the pointer to a desired main menu (DirectLink Mode, Room Monitor, Handset Setup, Answ. Setup, Global Setup, and System Reset).

3.Press SELECT/ to select the desired main menu.

4.Use VOL/RING/ or VOL/RING/ to select a desired submenu and then press SELECT/ to enter.

In the submenu, use VOL/RING/ or VOL/RING/ to select an item. Press SELECT/ to confirm your selection. For detailed instructions, see the following sections for the desired submenu.

5.To exit the menu, press END or place the handset to the cradle.

DirectLink Mode

Using the DirectLink Mode

1.Enter the DirectLink Mode menu (see “Entering the Menu” on page 17).

To enter DirectLink mode press [SELECT] appears.

2.Press SELECT/ to enter the DirectLink mode. You will hear a confirmation tone, and DirectLink Mode Complete appears.

3.To return back to the normal mode, exit the DirectLink mode. To exit the DirectLink mode, press MENU/DEL, and then SELECT/ , or return the handset to the cradle.

Setting Menu Options

17

Options Menu Setting

Room Monitor

Using Room Monitor

1.Enter the Room Monitor menu (see “Entering the Menu” on page 17).

To Room Monitor appears.

2.Select the handset or base you want to monitor by using VOL/RING/ or

VOL/RING/ .

When monitoring the other handset, be sure the other handset is facing up so the microphone can pick up the sound clearly.

3.Press SELECT/ .

RoomMonitor appears and you hear sounds in the room where the handset is installed.

Handset speaker is on the rear side. Place the handset so the speaker is not covered.

4.To finish the Room Monitor, press END or return the handset to the cradle.

Handset Setup

Selecting a Ringer Tone

1.Enter the Handset Setup menu, and then the Ringer Tones submenu (see “Entering the Menu” on page 17).

There are 10 ringer tones or 10 melodies to choose from.

•Ringers [Flicker, Clatter, Soft Alert, Wake Up, Light Bug, Beep Boop, Tone Board, Chip Chop, Party Clap, Reminder]

18

•Melodies [Beethoven’s Symphony #9 (Beethoven9), For Elise (Elise), We Wish You A Merry Christmas (MerryXmas), Home Sweet Home (Hm Swt Hm), Lorri Song #6 (Lorri Song), When the Irish Eyes Are Smiling (Irish Eyes), Aura Lee, Let Me Call You Sweet Heart (Sweetheart), Star Spangled Banner (Star Spngl), Old MacDonald (Old MacDld)]

2.Press VOL/RING/ or VOL/RING/ to move the pointer. You will hear the ringer or melody as you scroll through the options.

3.Press SELECT/ . You will hear a confirmation tone.

Distinctive Ringer Setup

1.Enter the Handset Setup menu, and then the Distinct. Ring submenu (see “Entering the Menu” on page 17).

2.Press VOL/RING/ or VOL/RING/ to select On or Off.

3.Press SELECT/ . You will hear a confirmation tone.

Setting the AutoTalk

1.Enter the Handset Setup menu, and then the Auto Talk submenu (see “Entering the Menu” on page 17).

2.Press VOL/RING/ or VOL/RING/ to select On or Off.

3.Press SELECT/ . You will hear a confirmation tone.

Setting Menu Options

19

Options Menu Setting

Setting the Anykey Answer

1.Enter the Handset Setup menu, and then the Anykey Answer submenu (see “Entering the Menu” on page 17).

2.Press VOL/RING/ or VOL/RING/ to select On or Off.

3.Press SELECT/ . You will hear a confirmation tone.

Setting the True Banner

1.Enter the Handset Setup menu, and then the Banner submenu (see “Entering the Menu” on page 17).

2.Use the number keypad (0-9), /tone/< #/>, or MENU/DEL to enter or edit the name.

3.Press SELECT/ . You will hear a confirmation tone.

Selecting a Language

1.Enter the Handset Setup menu, and then the Language submenu (see “Entering the Menu” on page 17).

2.Press VOL/RING/ or VOL/RING/ to choose English, Français

(French), or Español (Spanish).

3.Press SELECT/ . You will hear a confirmation tone.

Setting the Key Touch Tone

1.Enter the Handset Setup menu, and then the Key Touch Tone submenu (see “Entering the Menu” on page 17).

2.Press VOL/RING/ or VOL/RING/ to select On or Off.

20

3.Press SELECT/ . You will hear a confirmation tone.

Answering System Setup

You can also make these setting from the base (see page 52).

Setting a PIN Code

1.Enter the Answ. Setup menu, and then the Security Code submenu (see “Entering the Menu” on page 17).

2.Enter a two-digit PIN code (01-99) using the number keypad (0-9).

3.Press SELECT/ . You will hear a confirmation tone.

Setting the Ring Time

1.Enter the Answ. Setup menu, and then the Ring Time submenu (see “Entering the Menu” on page 17).

2.Press VOL/RING/ or VOL/RING/ to select a Ring Time (Toll Saver,

2 Times, 4 Times, or 6 Times).

3.Press SELECT/ . You will hear a confirmation tone.

Setting the Record Time

1.Enter the Answ. Setup menu, and then the Record Time submenu (see “Entering the Menu” on page 17).

2.Press VOL/RING/ or VOL/RING/ to select Record Time (1 Minute,

4 Minutes, or Announce Only).

3.Press SELECT/ . You will hear a confirmation tone.

Setting Menu Options

21