Size:
358 Kb
Download

RKP21x-208KVMSeries

RKP241x-208KVMSeries

USER’S MANUAL

WHERE TO BUY

http://www.rackmountnet.com

1933 O'Toole Ave, #A107 San Jose, CA 95131, USA

Toll Free Tel: (866)955-0598email: sales@rackmountnet.com

Introduction

Thank you for purchasing RKP215-208KVMRackmount LCD Keyboard Drawer with 8 ports KVM switch. LCD Keyboard Drawer with 8 ports KVM switch is ideal for application where space is critical.

RKP215-208KVMis a combination of keyboard, trackball, KVM switch and TFT LCD packed into a drawer with features such as monitor flip up design, adjustable mounting brackets, built in LCD OSD, centralized control of 8 PCs.

Features

Unique mechanical design to maximize rack mountable space

Unique monitor flip up design allows viewing through closed glass door of cabinet

Adjustable mounting brackets for multiple depth cabinets between 650mm and 1000mm

Lightweight aluminum construction – with a black anodize finish

High quality keyboard with integrated trackball

Keyboard options supporting twelve languages

Side to side wide-angleviewing as CRT monitor

Built in On Screen Display controlled by integral membrane switches

Power saving feature for prolonging the life of LCD panel

Standard D-sub15-pinVGA input connector

Front-accesslock for security

EMC shielding around the monitor housing to minimize interference

All mounting hardware included

Built in KVM switch function for easy controlling and monitoring up to 8 residing servers

Support eight character password protection and search PC server name

Auto scan mode for monitor PCs and flexible scan time from 5 ~ 99 sec

LED display for easy status monitoring

Supplied with eight screened cables 6 ft long

Rev. JUL-02

Packing Contents

RKP215-208KVMLCD Keyboard Drawer with KVM switch

1 PCS

User’s manual

1 PCS

AC to DC Power Adapter w/power cord

1 PCS

Rack Mount Kit

1 SET

Standard 3-in-1KVM cable

8 PCS

Before Unpacking

It is very important to locate the LCD Keyboard Drawer with KVM switch in a suitable environment.

zThe surface for placing and fixing the LCD Keyboard Drawer with KVM switch should be stable and level or mounted into a suitable cabinet.

zMake sure the place has good ventilation, is out of direct sunlight, sway from sources of excessive dust, dirt, heat, water, moisture and vibration.

zConvenience for connecting the LCD Keyboard Drawer with KVM switch to the related facilities should be well considers too.

Unpacking

The LCD Keyboard Drawer with KVM switch comes with the following standard parts shown as below. Check and make sure they are included and in good condition. If anything is missing, or damage, contact the supplier immediately.

Connection

The DC Power inlet and connection cables are located in the lower rear panel of the LCD

Keyboard Drawer.

 

 

1.

DC Power Inlet f

: plug in the AC to DC Power Adapter

2.

VGA

port

: Connect to VGA port in computer

3.

PS/2 Keyboard cable

:

Connect to keyboard port in computer

4.

PS/2 Mouse cable

:

Connect to mouse port in computer

Rev. JUL-02

Important Safeguards

Please read all of these instructions carefully before you use the device.

Save this manual for future reference.

zUnplug the LCD Keyboard Drawer with KVM switch from the power outlet before cleaning.

zDo not spray liquid cleaners or aerosol directly on the device. Wet a cloth with a neutral detergent (e.g. clean water) and squeeze it tight, then clean the screen slightly with it.

zDo not expose the LCD Keyboard Drawer with KVM switch directly to rain, water, moisture or sunlight.

zAvoid pressure on the LCD screen to prevent permanent damage to the display.

zDo not attempt to service the device yourself. Improper operation may void your warranty. Refer all servicing to qualified service personnel.

zSafe storage environment of the LCD Keyboard Drawer with KVM switch is ranging between –20oCand 60oC. Permanent damage could occur if the LCD Keyboard Drawer with KVM switch is stored outside the safe range.

zUnplug the LCD Keyboard Drawer witch KVM switch immediately and call a qualified service personnel under the following conditions:

1.The VGA signal cord is frayed or damaged.

2.If the monitor has been exposed to rain, liquid or water.

3.If the monitor has been dropped or the casing has been damaged.

What the warranty does not cover

1.Any product, on which the serial number has been defaced, modified or removed.

2.Damage, deterioration or malfunction resulting from:

a)Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to follow instructions supplied with the product.

b)Repair or attempted repair by anyone not authorized by us.

c)Any damage of the product due to shipment.

d)Removal or installation of the product.

e)Causes external to the product, such as electric power fluctuation or failure.

f)Use of supplies or parts not meeting our specifications.

g)Normal wear and tear.

h)Any other causes which does not relate to a product defect.

3.Removal, installation, and set-upservice charges.

Rev. JUL-02

LCD Session

Rev. JUL-02

On Screen Display - OSD

OSD is the convenient way for a user to adjust the screen performance to his satisfaction.

Menu / Selection

 

Left

 

 

Right

 

 

 

 

 

 

1.

Entering the OSD Meun

2.

Press the

to display the OSD main menu.

3.

Selecting icons for adjusting

4.

Use

buttons to scroll through the icons within the main menu and other sub-menus

 

the currently selected icon will be highlighted.

5.A slider bar is displayed whenever a value is to be sent. Usebuttons to scroll along the bar.

6.Saving the settings and Exit

7.Selections / selected values is automatically saved once made.

Rev. JUL-02

8. Select “Auto” for autoadjust LCD quality

Rev. JUL-02

Customizing the Settings

1. Brightness

• To perform brightness adjustment of the input RGB signal

2. Contrast

To adjust the contrast level of the input signal

3. Phase

To optimize the picture quality by adjusting the sampling clock of the input RGB Signal

4. Frequency

To adjust the frequency of the input signal to optimize the picture quality

5. H - Position

To adjust the horizontal position of the frame

6. V - Position

To adjust the vertical position of the frame

7. Sharpness

To enhance more sharpening on the appearance of images

8. Color Temperature

To enter into the Color temperature sub-menu

Rev. JUL-02

1. H - Position

• To adjust the horizontal position of the OSD frame

2. V - Position

• To adjust the vertical position of the OSD frame

3. Half Tone

• To switch the OSD color from full color to half tone

4. OSD Timeout

To modify the duration of the OSD time-out

1. Information

• To display the existing input signal information

2. Reset

To reset the LCD to factory setting

Rev. JUL-02

3.Half Tone

To switch LCD power ON/OFF auto mode

Resolution Setting

Step 1 – Press right click on the desktop

Step 2 – Choose “Properties”

Step 3 – change the “Screen Resolution”

Step 4 – change the “Screen refresh rate”

Rev. JUL-02

FAQ

My display doesn’t work, even though the computer appears to work

1.Make sure the power cable is securely plugged into the display

2.Make sure the display is turned on

3.Try turning the display off and then turning it on again

4.Make sure the display’s power cord is plugged into a power outlet and into the AC power adapter. Check to see whether the outlet works by plugging another device into the outlet

5.Check the connection between the display and the computer, The cable connectors must be pushed in all the way

The message “Check Cable” appears on my display

1.This message appears when the video cable is not properly connected to the computer

2.Make sure the analog video cable is plugged into the Analog Video Input port on the back of the display

3.Make sure the other end of analog video cable is plugged into the PC’s video port

The message “No Sync” appears on my display

1.This message appears when there is no video signal from the computer a. with cable already connected

2.Make sure that the computer’s power is turn on

3.Make sure that your graphic card has its output already

The message “Signal Out of Range” appears on my display

1.This message appears when the input signal is beyond the display’s capability

2.13.3” 1024 x 768 at 70Hz (Max.)

3.15.1” 1024 x 768 at 75Hz (Max.)

4.17.1” 1280 x 1024 at 75Hz (Max.)

Rev. JUL-02

FAQ – Sun Server

Sun Server are using resolution at 1152 x 900 x 76Hz

Supported resolution mode

640 x 480 x 70/75Hz

800 x 600 x 70/75Hz

1024 x 768 x 70/75Hz

1280 x 1024 x 75Hz (17” LCD)

Note the Max. frequency of 13.3” is 70Hz

You need to change the Sun Server resolution before you connect to LCD Display

Please do the following procedure to change the resolution setting :

1.as root:

you may find the following comment “/user/sbin/m64config”

2.Type “/user/sbin/m64config – prconf” to view current resolution

3.Type “/user/sbin/m64config – res 1024x768x70 now” to change to 1024x768 @ 70MHZ

4.the screen will be rubbish

5.Then type “pkill Xsun”

6.And Type “pkill Xsession” to restart the Xsession Remember this process need to RESTART the server

Under Common Desktop Environment (CDE)

To change the OpenBoot resolution, you can type the following commend in OK prompt

1.In OK prompt, type “setenv output-devicescreen:r1024x768x70”

2.Type “printenv” to confirm the resolution has been changed to 1024x768x70Hz

3.Then type “reset” to restart the system

Remember this process need to RESTART the server

Rev. JUL-02

Technical Information

LCD

Size

17”

 

Screen Type

TFT Active Matrix

 

Display Area

337.92mm(H) x 270.336mm(V)

 

Contrast Ratio

350 : 1

 

Viewing Angle

150{ (H) x 125{ (V) Typ.

 

Resolution

XGA 1280 x 1024

 

Pixel pitch

0.264mm (H) x 0.264mm (W)

 

Response Time

Tr=5ms, Tf=20ms Typ

 

Brightness

250 cd/m2

 

Panel Color

16.7M Colors

 

Back Light

4 Lamps

Video

Synchronization

Horizontal : 31-69KHz

 

Range

Vertical : 56-75Hz

 

Input Signal

Analog RGB 0.7Vp-p

Power Management

VESA DPMS

Control

Power

Micro on/off switch on the backside

 

OSD Control

Brightness, Contrast, Color,

 

 

H position, V position, Auto config,

 

 

OSD adjust, Dither, etc.

 

 

 

External Connection

Power Input

12V/5A DC adapter

 

Video Input

15-pinD-Subconnector

 

 

 

LCD

Size

15”

 

Screen Type

TFT

 

Display Area

304.1mm(H) x 228.1mm(V)

 

Contrast Ratio

300 : 1

 

Viewing Angle

130{ (H) x 110{ (V) Typ

 

Resolution

1024 x 768

 

Pixel pitch

0.297mm (H) x 0.297mm (W)

 

Response Time

Tr=5ms, Tf=20ms Typ

 

Brightness

250 cd/m2

 

Panel Color

16.2M

 

Back Light

4 CCFTs (Cold Cathode Fluorescent

 

 

tube)

Video

Synchronization

Horizontal : 48.36-60KHz

 

Range

Vertical : 56-75KHz

 

Input Signal

Analog RGB 0.7Vp-p

Power Management

VESA DPMS

Control

Power

Micro on/off switch on the backside

 

OSD Control

Brightness, Contrast, Color,

 

 

H position, V position, Clock, Phase,

 

 

Auto config, Scaling, Input select,

 

 

Clear EEPROM, Multi window,

 

 

OSD adjust, Save

 

 

 

External Connection

Power Input

12V/5A DC adapter

 

Video Input

15-pinD-Subconnector

Rev. JUL-02

KVM Session

Rev. JUL-02

KVM

Bank Button

 

Channel Button

 

 

 

PS/2 Cable:

Mini Din 6 pin Male to Male

VGA Cable:

HDB15 pin Male to Male

Installation

Before installation, please make sure all of peripherals and computers have been turned off.

1.Connect the Keyboard, VGA, Mouse cables to the computer ports of KVM switch

2.After Powering on computers and finishing the boot-upprocess, you can start to go KVM switch.

Note:

Please don’t switch the PC port (i.e. Don’t press the push button of KVM switch or run hot key) during the computers are under boot-upprocess.

Rev. JUL-02

Startup

1.Power on the KVM power

2.7 segments LED is on

3.Key-inthe password, default is “00000000”

4.If you forget your password, please send back to Manufacturer / Distributor

5. Pressing to view all port

1

2

3

4

8

7

6

5

LED Indication

When you change the channel

If the PC is turn off or is disconnected

The LED will flash otherwise is will lit

Keyboard hot key command

Simple key sequence

Press “ Scroll Lock” twice within 2sec

Follow with a beep sound, going into the hot key mode

Need to key in the hot key within 2 sec

Go back to Operation System Control state

Rev. JUL-02

ROM REFLASH

Hot Key

Press “Bank” & “Channel” at the same time to reset the KVM switch to default setting

S.L. + S.L. +

Previous Channel

S.L. + S.L. +

Next Channel

Note: You also could press “up arrow key” or “down arrow key” longer time to speed up selecting the destination port

S.L. + S.L. +

Page Up

Previous Bank

S.L. + S.L. +

Page Down

Next Bank

To Select PC port

S.L. + S.L. + Bank No.+ Port No.

Bank No. 1 – 8 (Max.) Port No. 01 – 16 (Max.)

Example we select Bank 3 Channel 14

S.L. + S.L. + 3 + 14

Example we select Bank 7 Channel 5

S.L. + S.L. + 7 + 05

Beeper On/Off

S.L. + S.L. + B (Default is On)

Auto Scan

S.L. + S.L. + S (Default is 10 sec from P to P)

Press any key to stop

Rom Refresh

S.L. + S.L. + R (Refresh to OSD Default Value) Not include the PASSWORD

Find by PC name

• S.L. + S.L. +F

F I N D :

Key the PC name

Search PC name starting from 1st PC port

OSD Menu

S.L. + S.L. + Spacebar

Rev. JUL-02

Rev. JUL-02

OSD Menu

 

 

 

 

 

Bank No.

 

BANK : 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

01

SYSTEM 01

02

SYSTEM 02 (

 

 

 

 

03

SYSTEM 03

04

SYSTEM 04

 

 

 

 

 

 

 

 

 

 

PC Name List

05

SYSTEM 05

06

SYSTEM 06

 

 

 

 

 

 

 

 

 

 

 

 

07 SYSTEM

07

08

SYSTEM 08

 

 

OSD : 1 0 SEC.

CHANGE PASSWORD

SCAN: 1 0 SEC.

CONSOLE

ON/OFF

 

 

 

 

KVM Settings

ESC : QUIT

ENTER :COMPLETE

TAB : NEXT

INSERT :EDIT

Info.

Ç/È: SELECT PORT

PgDn/PgUp: BANK SELECT

Use “Tab” key to select items like Bank, OSD, SCAN, CHANGE PASSWORD, CONSOLE ON/OFF, etc…

Use Page Up &Page Down to switch previous or next bank

Rev. JUL-02

OSD Menu

BANK : 1

01

SYSTEM 01

02

SYSTEM

02 (

03

SYSTEM 03

04

SYSTEM

04

05

SYSTEM 05

06

SYSTEM 06

07

SYSTEM 07

08

SYSTEM

08

 

 

 

 

 

OSD : 1 0 SEC.

CHANGE PASSWORD

SCAN: 1 0 SEC.

CONSOLE ON/OFF

 

 

ESC : QUIT

ENTER :COMPLETE

TAB : NEXT

INSERT :EDIT

Ç/È: SELECT PORT

PgDn/PgUp: BANK SELECT

PC Name List

“ ” near to the PC name represents the PC system is powered on

Use up arrow key “Ç” or down arrow key “È” to select port for destination PC name and press “Enter” to select

Edit PC name

Press “Ins” key for editing PC name

PC name should not more than 8 characters

After finish edit press “Enter”

OSD – 10 sec

OSD window display or PC name exist 10 sec

Default Value is 10 sec

Modify from 05 – 99 sec

Scan – 10 sec

Scan interval from one PC port to next PC port is 10 sec

Default Value is 10 sec

Max. 99 sec

Rev. JUL-02