Files for Q-See QSDT404C
Size:
534.59 Kb
Download

QSDT404C

User’s Manual

Contact US:

Q-seeProducts8015E.Crystal Dr Anaheim, CA 92807 Website: http://www.q-see.com Customer Service: Phone: 877-998-3440 x 538 Email:cs@dpsi-usa.com Tech Support:

Phone: 877-998-3440x 539Email:ts@dpsi-usa.comFax:

714-998-3509

Rev 032109

TABLE OF CONTENTS

FCC STATEMENT………………….………………………………….……3

1.INTRODUCTION.…………………………………..…………………....3

2.WHAT’S INCLUDED…..…………………………………………………3

3.MAIN FEATURES……………………………………..………………....3

4.BUTTONS ON RECEIVER………………….…………………………..4

5.SIDE PANEL………………….…………………………..………………5

6.CAMERA INSTALLATION………………….……………………………6

7.MENU…………………………………………………………………….. 7

8.TROUBLESHOOTING………………….…………………………..……8

9.TECHNICAL SPECIFICATIONS……………………………………….. 9

10.NOTES…………………………………………………………………. 10

Q-SEEPRODUCT WARRANTY………………….……………….…….. 10

2

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

1 Introduction

This miniature size product adopts an advanced microwave and wireless transfer technology developed and manufactured with 2.4GHz wireless digital receiving modules, which has stable performance and a strong anti-interferencefunction. This product can be used with wireless cameras to record wireless camera signals.

2 What's included:

The following items should be included in the box. Please check that you have them all before installation.

A One receiver

B One power adapter for the receiver C 1 camera with power adapter

D One RCA cable

E stands of camera and receiver F screws for camera mounting

3Main features.

3.1Supports up to 4 cameras simultaneously.

3.2Digital 2.4G wireless modules.

3.3Supports A/V output from receiver

3.4Supports AE and AWB

3.5Supports OSD (On Screen Display) screen-controlledoperation

3.6Supports 4 Channels displayed in order

3.7Supports automatic channel switch

3.8Transmission distance up to 100M (Tested in open air)

3.9M-JPEGformat Compression

3

4 Buttons On Receiver

4.1Mode switching Switch between quad mode and single channel mode

4.2

Pairing

Pairing the cameras and receiver

4.3

Menu

OSD menu display

4.4

Auto Scan

Switching the channels automatically with set time interval

4.5

Right/CH2

Move to the Right / Switch to Channel 2

4.6

Up/CH1

Move Up / Switch to Channel 1

4.7Manual Scan Switching the channel manually

4.8Down/Ch3: Move Down / Switch to Channel 3

4.9

Left/CH4

Move to the Left / Switch to Channel 4

4.10

SMA Antenna

SMA antenna plug in

4.11

Power LED

Red Light when power on

4

5 Side panel

5.1A/v output

5.2Power input (DC 9V)

5

6 Camera Installation

6.1Camera stand mounting screw (for ceiling mount)

6.2Power in cable (DC 5V input)

6.3Pairing button

6.4SMA antenna plug

6.5Camera stand mounting screw (for desk top mount)

6.6Microphone

6

7 Menu

Enter the Menu option to setup the main feature of this product.

Through Right/Left button can adjust parameters, and throughUp/Down button can select the features to set.

7.1Resolution (High / Low): When set to low, the image is not as clear, but it displays more frames per second. When set to high, the image will be clearer, but it displays fewer frames per second.

7.2SCAN TIME This option sets the time interval between cameras when

switching channels automatically. OFF Scan is inactive. When on options are: 5 seconds to 20 seconds between cameras.

7.3AUDIO VOL: Adjust the volume of the audio from 0 to 20. Use the Left/right button to reduce/increase the volume.

7.4BRIGHTNESS: Adjust the brightness of images, range of brightness is from 0 to 5, use the Left/right button to adjust it.

7.5PAIR: Use this option to pair the cameras with specific channels, press thePair button, use the Right/Left button to choose the channel; one channel can only pair with one camera. After selecting the specific channel and pressing the pair button again the window below will appear:

7

Press the Pair the button on corresponding camera and wait for a while, the monitor connected to the receiver will display the images from the cameras that have been matched. Pairing succeeded.

7.6TV OUT: This option allows you to select the video format (NTSC/PAL) for video output resources. In the United States we use NTSC format.

7.7Channel selection keys

You may select channels by using the corresponding keys on the receiver to manually choose channel.

Channel 1 Up

Channel 2 Right

Channel 3 Down

Channel 4 Left

Circulation Button Monitor screen circulates the image from Channel 1 to

Channel4 then back to Channel1. The receiver will skip the channels that do not have cameras assigned to them.

8 Troubleshooting

Symptom

Remedy

 

 

The power does not

Check that the AC power cord is connected securely.

turn on.

(In case of power failure) Check the breaker.

 

Check if Monitor is on and video format (NTSC / PAL)

No image display on

is correct.

Check monitor’s video cable and connections.

monitor

Confirm that the camera has power.

 

 

 

There is no sound.

Check if the audio cable is well connected to monitor.

 

 

 

If there is a microwave oven close by, turn the microwave oven

 

off.

Interruption in

You may have other units that run on the 2.4GHz signal. Move

Image and Sound

their base away from both the transmitter and/or the receiver

 

Your home may have a metal frame that reduces the range of the

 

unit.

Poor Reception

Move the Cameras and/or the receiver around to see it reception

Quality

improves.

8

Try resetting Pairing between camera and receiver

9 Technical specifications

9

10 Notes

10.1This product can be damaged by pressure or impact.

10

10.2Any repair of this product should only be done by Professionals.

10.3This product should only be opened by Professionals.

10.4This product can not be used in high temperature environments.

10.5Replacement Parts – When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

10.6Digital Peripheral Solutions does not accept responsibility for any illegal use of this product by the customer.

Q-SEEPRODUCT WARRANTY

Thank you for choosing our products.

All of our product users have a conditional free warranty repair service for hardware within 12 months starting from the purchase date, and a free exchange service within one month (valid for manufacturing defects). Permanent upgrading service is provided for the software.

Liability Exclusions:

Any product malfunction, abnormalities in operation or damage caused by the following reasons are not within the free service scope of our company. Please select payable service.

(1)Equipment damage caused by improper operation

(2)Improper environment and conditions in/on which the equipment operates, e.g., improper power, environment temperature, humidity and lightening strike etc. that cause equipment damage.

(3)Damage caused by acts of nature: earthquake and fire etc.

(4)Equipment damage caused by the maintenance of personnel not authorized by our company.

(5)Product sold over 12 months ago.

In order for us to provide various services to you please complete the registration procedure after you purchase the product. Cut off or copy User’s Information Card and fax or mail it to us after the card is filled in. You can also register the product by going to the www.q-see.com website and clicking on the Register link.

Customer Information Card

User’s Name

Mr./Mrs.

Company

 

11

Name

Postal

Address

Postal code

Phone

Number

E-mail

Model

Number of

Product

Serial Number

of Product

Purchase

Date

Distributor

If you have questions:

Contact Us:

Mailing Address:

Customer Service:

DPS Inc.

Phone: 877-998-3440x 538

8015 E. Crystal Dr

Email: cs@dpsi-usa.com

Anaheim, CA 92807

 

Website:

Tech Support:

http://www.q-see.com

Phone: 877-998-3440x 539

Fax:

Email: ts@dpsi-usa.com

714-998-3509

 

The material in this document is the intellectual property of our company.

No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without our company’s prior written permission.

1. Our products are under continual improvement and we reserve the right to make changes without notice, therefore no guarantee is given as to the correctness of its contents.

12

2.We do not accept any responsibility for any harm caused by using our product.

3.The product picture may differ from the actual product, which is only for your reference. The accessories may be different in different selling areas. For details of accessories, please refer to your local distributor.

Copyright reserved

13