congratulations...
On your purchase of a Pyramid Signature Series amplifier. This amplifier extends the pyramid tradition into a totally new series of amps, designed from the ground up to deliver the power, performance and flexibility the modern car audio enthusiast demands.
When you check the list of features offered by the PB744,PB844 and PB1644, you’ll know you made the right choice with a Pyramid Power amplifier.
precautions
Do not operate the amplifier when it is unmounted, Attach all audio system components securely within the automobile to prevent damage, especially in an accident.
Do not mount this amplifier so that the wire connections are unprotected, or in a pinched condition, or likely to be
damaged by nearby objects.
.
Before making or breaking power connections in your system, disconnect the vehicle battery. Confirm that your head unit or other equipment is turned off while connecting the input jacks and speaker terminals.
If you need to replace the power fuse, do so only with a fuse identical to that supplied with the amplifier. Using a fuse of a different type or rating may result in damage that isn’t covered in the manufacturer’s warranty.
notes
23
protection
circuitry
The built-in protection circuitry in the Pyramid Signature amplifiers will disable the amplifier if it senses an input overload, a speaker short circuit, or extreme temperature conditions.
When the protection circuit is activated by any of these conditions, the Protection LED will be illuminated.
If this occurs ,carefully inspect the system to determine the source of the problem.
If the shutdown was a result of a thermal overload condition, allow the amplifier to cool down before attempting to restart it.
If the shutdown was a result of an input overload, or speaker short circuit, be sure to corr the condition before restarting.
The amplifier can be restarted by turning the remote power OFF and then ON again.
troubleshooting
No output.
Confirm that all terminal strip connections are secure and tight.
Check both in-line and built-in fuses. Both the +12V and the Remote terminals
must have +12V referenced to chassis ground.
Confirm that the audio signal source(car radio, equalizer, etc.) Is connected and is supplying output signal. To check if the amp is supplying signal, unplug the cables from the signal source(but leave them plugged into the amp).
Briefly tap the center pin of each of the disconnected RCA plugs with your finger. This should produce a noise)feedback) in your speakers.
Only one channel works. |
2 |
Confirm that all terminal strip connections are secure and tight. |
|
Check the Balance control on the head unit(or other source) to verify |
that it |
24 |
is set to its midpoint.
If you are using the Low Level RCA input , reverse the input plugs at the amplifier(i.e.,switch the L with the R). If the channels which is silent switches to the other side, the problem is either in the head unit/other source or the connecting cables.
Weak output.
Readjust the Input Level Control(s) to better suit the input signal.
Noise in the audio.
If the noise is a “whine” whose pitch follows the engine speed, confirm that
the amplifier and any other signal sources(hesd unit, etc.) Are properly ground.
If the noise is a “clicking” or “popping” noise whose rate follows the engine speed, this usually means that the vehicle is equipped with resistor spark plugs and wires, or that the ignition is in need of service.
Check the routing of the speaker and input wires to make sure they are not adjacent to wire which interconnect lights and other accessories.
If the above steps fail to improve or clear noise interference, the system should be checked by a professional mobile audio installer.
table of contents
general features |
2 |
mono input connections |
15 |
|
|
features and speifications |
|
4CH amp PB844 PB1644 |
|
||
|
|
|
|
||
2ch amp PB744 |
3-4 |
speaker connections |
|
|
|
4ch amp PB844 |
5-6 |
2ch amp PB744 16 |
|
||
4ch amp PB1644 |
7-8 |
4CH amp PB844 |
17-18 |
|
|
|
|
|
|||
electrical connections |
|
4CH amp PB844 |
19-20 |
|
|
|
|
|
|
||
2ch amp PB744 |
9 |
mounting and installation |
21 |
1 |
|
4ch amp PB844 |
10 |
||||
|
|
||||
4ch amp PB1644 |
11 |
protection circuitry and troubleshooting |
22 |
||
stereo input connections |
12 |
||||
2CH amp PB744 |
precautions |
23 |
|
||
mono input connections |
|
|
|
|
|
2CH amp PB744 |
13 |
|
|
|
|
2/4 channel input connections |
|
|
|
|
|
4CH amp PB844 PB1644 |
14 |
|
|
|
general features
PB744 |
PB844 |
PB1644 |
|
High Performance 1000Watt 2 channel |
High Performance 1600Watt 4 channel |
High Performance 4000Watt 4 channel |
|
Bridgeable MOSFET Amplifier |
Bridgeable MOSFET Amplifier |
Bridgeable MOSFET Amplifier |
|
|
|
|
|
500 Watts×2 Output |
400 Watts×4 Output |
1000 Watts×4 Output |
|
|
|
|
|
1000 Watts×1 Bridged Output |
800 Watts× 2 Bridged Output (400W×2+800W×1) |
2000 Watts× 2 Bridged Output (100W×2+2000W×1) |
|
|
|
|
|
Variable Hi/Lo Electronic Crossover Network |
Variable Hi/Lo Electronic Crossover Network |
Variable Hi/Lo Electronic Crossover Network |
|
|
|
|
|
Variable Bass Boost(0-+18dB@60Hz) |
Variable Bass Boost(0-+18dB@60Hz) |
Variable Bass Boost(0-+18dB@60Hz) |
|
|
|
|
|
Variable Input Level(Gain)Control |
Variable Input Level(Gain)Control |
Variable Input Level(Gain)Control |
|
|
|
|
|
Remote Turn on/Off |
Remote Turn on/Off |
Remote Turn on/Off |
|
|
|
|
|
RCA Inputs |
RCA Inputs |
RCA Inputs |
|
|
|
|
|
MultiFuntion VFD |
MultiFuntion VFD |
MultiFuntion VFD |
|
|
|
|
2 |
Power ON LED Indicator |
Power ON LED Indicator |
Power ON LED Indicator |
|
|
|
|
|
LED Protection Indicator |
LED Protection Indicator |
LED Protection Indicator |
|
|
|
|
|
S/N Ratio: >95dB |
S/N Ratio: >95dB |
S/N Ratio: >95dB |
|
|
|
|
|
THD :<0.04% |
THD :<0.04% |
THD :<0.04% |
|
|
|
|
|
Thermal Protection |
Thermal Protection |
Thermal Protection |
|
|
|
|
|
Overload Protection |
Overload Protection |
Overload Protection |
|
|
|
|
|
Short Circuit Protection |
Short Circuit Protection |
Short Circuit Protection |
|
|
|
|
|
Anti-Thump Turn-On |
Anti-Thump Turn-On |
Anti-Thump Turn-On |
|
mounting and installation
Your new Pyramid Signature Series amplifier comes complete with required mounting hardware. When determining a suitable location in your vehicle for the amp, please remember that it is a highpower electronic device capable of generating high heat.
For this reason, always choose a location in your vehicle which has low vibration, adequate
ventilation, a minimum of dust, and no moisture.Be sure to mount the amp in such a manner as to allow reasonable airflow over the cooling fins.
Mark the location for the mounting screw holes by positioning the amp where you wish to install it and use a scribe (or one of the mounting screws) inserted in each of the mounting holes to mark the mounting surface for the mounting surface. If the mounting surface is carpeted, measure the hole centers and mark with a felt tip pen.
Before attempting to drill the mounting holes, take note of any wires, lines or otherdevices in your vehicle which may be located behind the mounting surface! Then drill pilot holes in the mounting surface for the mounting screws and insert them. Tighten the screws securely.
When making electrical connections to your amplifier, please observe the following: 213
Use at least 8 gauge wire for power and ground connections. Wire the amplifier directly to the car battery.
For the ground connection, use the shortest possible wire to a good chassis ground point.
Wire the Remote connection to the auto start lead of your head unit, equalizer or power antenna.
About power fuses:
Pyramid Signature Series amplifiers feature built-in fuse systems. These fuses protect both the amplifier and the electrical system in your vehicle from fault conditions. If you ever need to replace the fuse in your Pyramid Signature Series amp, use a fuse of exactly the same type and rating. A different type or rating of fuse may result in damage or fire.
speaker connections
4ch amp PB1644
2CH Bridged Output Mode With Subwoofer Output
PB1644
R |
MINIMUN |
|
SPEAKER |
|
|
SPEAKERS |
IMPEDANCE |
20 |
L |
4OHMS! |
|
SUBWOOFER |
|
|
PB1217
protection LED
features and controls
2ch amp PB744
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
output level |
|
|
low level inputs |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
PB744 |
power LED |
|
|
|
|
|
|
remote bass boost |
3 |
|||||||||||
high pass frequency control |
|
|
|
|
|
|
|
input level control |
||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
low pass frequency control |
|
|
|
|
|
|
|
|
|
|
|
bass boost level |
|
||||||
|
|
|
|
|
|
|
|
|
crossover mode selector |
|
speaker connections |
power fuse |
|
power terminals |
||
|
||
SPEAKER OUTPUT |
|