Specifications
PYD1910/1920/1930/1940/1950
Input Sensitivity/Impedance
Mic 1-2 |
1.5 mV/600 Ohms, bal/unbal |
Phono 1-2 |
3.0 mV/50K Ohms |
Line 1-6 |
150.0 mV/27K Ohms |
|
|
Output Level |
|
Amp |
2.0 V/10-kOhms |
Zone |
2.0 V/10-kOhms |
Record |
150mV/10-kOhms |
|
|
Frequency Response |
20Hz – 20kHz +/- 3 dB |
|
|
S/N Ratio (at 1 kHz) |
|
Mic |
>60 dB/1.5mV input |
Phono |
>70 dB/3.0mV input |
Line |
>80 dB/150.0 mV input |
|
|
Distortion |
|
Mic |
0.20% |
Phono |
0.05% |
Line |
0.03% |
Equalizer |
30, 60, 120, 250, 500 |
|
|
Control Frequencies |
|
||
|
1K, 2K, 4K, 8K, and 16KHz |
||
Boost/Cut Range |
+/- 10 dB from center |
||
|
|
|
|
MIC Tone Control |
10kHz; |
+10/-30dB |
|
Treble |
|||
Mid |
1 kHz; |
+10/-30dB |
|
Bass |
100Hz; |
+10/-30dB |
|
|
|
|
|
Talkover Attenuation |
-16dB |
|
|
|
|
|
|
Echo Delay Time |
50mS-120mS |
||
(PYD-1920/1940) |
|
|
|
|
|
|
|
Sampling Length |
12 Seconds |
||
(PYD-1950) |
|
|
|
|
|
|
|
Power Source |
120 VAC, 60Hz/230 VAC, 50 Hz |
||
|
|
|
|
Dimensions, inches |
19.0 x 4.13 x 9.45 |
||
(mm) |
(482 x 105 x 240) |
Limited Warranty |
|
|
|
All PYLE PRO products are carefully constructed and tested before shipment. |
|
R.A.#: _____________ |
|
Units purchased in the USA are warranted to be free of defects in material |
|
||
|
PYLE PRO Service Center |
||
and workmanship for two (2) years from the date of purchase. This warranty |
|
||
|
1600 63rd Street |
||
is limited to the original retail purchaser of the mixer. |
|
||
|
Brooklyn, NY 11204 |
||
|
|
||
Should the unit fail due to factory defects in material or workmanship, your |
You must also include the following items with your return: |
||
• |
A copy of your sales receipt or other proof of purchase |
||
unit will be repaired or replaced at the sole discretion of PYLE. |
|||
|
• |
A brief letter, indicating the problem you are experiencing with the product |
|
To obtain warranty service, you must first call our Consumer Return Hotline |
• |
Include in your letter your return address, daytime phone number and R.A. number |
|
• |
Also include a check or money order for $15.00 for return |
||
at (718) 236-6948 to obtain a Return Authorization Number. This R.A. # must |
shipping, handling and insurance, or provide your Visa/MC number with expiration date. |
||
appear on the outside of your package and on all paperwork relating to your |
Our obligation under this warranty is limited to the repair or replacement |
||
return. |
|||
|
of the defective unit when it is returned to us prepaid. This warranty will |
||
When returning the unit to us for warranty service, it must be carefully |
be considered void if the unit was tampered with, improperly serviced or |
||
packed and shipped, prepaid, to: |
subject to misuse, neglect or accidental damage. |
||
|
|
|
Please complete warranty card, detach and return
Thank you for purchasing this PYLE
product. To activate your |
warranty registration card |
|
|
warranty, please mail this card |
|
|
|
within 10 days. |
|
PYLE PRO MIXERS
Name
Address
City, State ZIP
|
Model No. |
Serial # (if available) |
||||
|
Date of Purchase |
|
|
|
|
www.pyleaudio.com |
|
|
|
|
|
|
|
|
|
|
|
|
14 – Pyle Pro Mixer Owner’s Manual |
|
|
Purchased at: |
|
|
|
|
|
|
Music Products Store |
Sound Contractor/Installer Mail Order |
|
|
||
|
Catalog Merchandiser |
Other |
|
|
|
|
|
|
|
|
|
|
|
pro series
PYD-1910/PYD1920 PYD-1930/PYD-1940
PYD-1950
4 channel
professional
Your PYLE PRO Series Performance Mixer
is a sophisticated control center, perfect for mixing sound from multiple playback sources such as microphones, tuners, CD players, turntables or the audio outputs from a VCR. This mixer is ruggedly constructed for home or professional use. Wide range volume controls permit you to adjust sound levels accurately to achieve just the right mix for playing through your speaker system or for recording.
Please read this manual thoroughly before you attempt to set up and use the mixer. It contains a range of suggestions and instructions to insure safe usage. Set up and used properly, you can expect years of trouble-free service from this product.
Owner’s Manual Table of Contents
i |
Input/Output Features |
10 |
Monitoring (”Cueing”) Inputs |
1 |
Features and Controls: PYD-1910 |
|
Mixing Inputs |
2 |
Features and Controls: PYD-1920 |
|
Adding Equalization to the Mix |
3 |
Features and Controls: PYD-1930 |
11 |
Adding External Effects to the Mix |
4 |
Features and Controls: PYD-1940 |
|
Using the MicrophoneTalkover Mode |
5 |
Features and Controls: PYD-1950 |
|
Microphone Tone and Level Controls |
6 |
Presetting Controls Before Use |
|
Using the MIC Kill Frequency Switches |
|
Connecting the Mixer Inputs |
12 |
Using the Mono/Stereo Switch |
8 |
Using the Gain Controls |
|
Using the Crossfader w/Assign Switches |
|
Connecting the Mixer’s Outputs |
|
Using the Echo Controls (PYD-1920 and PYD-1940) |
|
to Amplifiers |
|
Using the Sound Effects (PYD-1930 and PYD-1940) |
|
to Recorders |
|
Using the Digital Sampler (PYD-1950) |
|
to Zone Speakers |
13 |
Troubleshooting |
9 |
Using Headphones |
|
Care and Maintenance |
|
Connecting the Lamp |
14 |
Specifications |
10 |
Using the Mixer Controls |
|
Warranty |
|
Turning On the Mixer |
|
|
Input/Output Features: all models
Effects Send/Receive jacks permits you to either include |
|
|
|
|
Stereo Line Inputs let you connect |
|||||||
externally generated effects (such as a digital sampler or synth) |
|
|
|
|
most high-level audio sources, such as |
|||||||
IN the mix, or to process the mixed sound (echo reverb, etc.). |
|
|
|
|
CD players, tape deck, tuner or VCR. |
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Output Jacks to connect the mixer to a receiver or amplifier – choose to use cables with either 1/4” plugs or RCA plugs.
Zone Output Jacks to connect the mixer to a second receiver or amplifier powering speakers in the DJ booth or in a remote location
Record Output Jacks to connect the mixer to a tape deck for recording the mixed program
Dual Purpose Stereo Inputs for using a turntable with a magnetic cartridge OR a high level input source
Input Select Switches – set these switches based on what is plugged into Phono1/Line1 and Phono2/Line3 input jacks
Ground Screw for turntables
MIC2 Microphone connector permits you to connect a balanced or unbalanced low impedance microphone with 1/4” plug.
Features and Controls: PYD1910 Mixer
MIC 1 Combo Input Jack For connecting a balanced or unbalanced low impedance microphone with XLRtype or 1/4” plug
MIC 2 Input Jack (on input panel)
For connecting a balanced or unbalanced low impedance microphone with 1/4”plug
MIC Frequency Kill Switches Allows you to kill the selected frequency range instantly for interesting effects. LED lights to indicate kill is activated.
MIC Talkover Allows you to lower the level of the input sources so you can talk them using the DJ Mic
MIC1/2 Level Controls Lets you control the MIC levels as they enter the mix
MIC1/2 Tone Controls
Channel Gain Control Lets you adjust the gain of the input source
Channel Input Selector Lets you choose the input source to play for each channel
Channel CUE Switch Allows you to monitor the selected audio input source and prepare it prior to mixing it in.
Dual Display Meter Indicates the levels of Left and Right Master Channels
10-Band Equalizer Allows you to tailor the mixer output to suit your taste or performance environment. Each frequency range can be cut or boost by up to 10dB.
BNC Lamp Adaptor Allows you to connect a 12V/3W lamp to light the panel
Power Switch and LED
Indicator
Equalizer On/Off Switch
Effect Switch (Send/Receive) Lets you connect a sound effect device, such as reverb, sampler, etc. and either play the signal from it or play another input through it.
Headphone Level Control
Headphone Jack
Accepts headphones with 1/4” plug
Headphone CUE/PGM Control Allows you to listen simultaneously or separately to the CUE material or the active program
Zone Level Control Lets you control the mixer’s overall ZONE volume level, if you set up remote speakers or DJ booth monitors
Zone Mono/Stereo Selector
Zone Balance Control
Master Level Control Lets you control mixer’s overall volume level
Master Mono/Stereo Selector
Master Balance Control
Channel Assign Switch Lets you select the input source to be mixed by the Crossfade Slider Control
Crossfade Slider Control Allows you to smoothly switch between the input sources assigned to Channel A and Channel B
i – Pyle Pro Mixer Owner’s Manual |
Pyle Pro Mixer Owner’s Manual – 1 |
Features and Controls: PYD1920 Mixer
MIC 1 Combo Input Jack For connecting a balanced or unbalanced low impedance microphone with XLRtype or 1/4” plug
MIC 2 Input Jack (on input panel)
For connecting a balanced or unbalanced low impedance microphone with 1/4” plug
MIC Frequency Kill Switches Allows you to kill the selected frequency range instantly for interesting effects. LED lights to indicate kill is activated.
MIC Talkover Allows you to lower the level of the input sources so you can talk them using the DJ Mic
MIC1/2 Level Controls Lets you control the MIC levels as they enter the mix
MIC1/2 Tone Controls
Channel Gain Control Lets you adjust the gain of the input source
Channel Input Selector Lets you choose the input source to play for each channel
Channel CUE Switch Allows you to monitor the selected audio input source and prepare it prior to mixing it in.
Dual Display Meter Indicates the levels of Left and Right Master Channels
10-Band Equalizer Allows you to tailor the mixer output to suit your taste or performance environment. Each frequency range can be cut or boost by up to 10dB.
BNC Lamp Adaptor Allows you to connect a 12V/3W lamp to light the panel
Power Switch and LED
Indicator
Equalizer On/Off Switch
Effect Switch (Send/Receive) Lets you connect a sound effect device, such as reverb, sampler, etc. and either play the signal from it or play another input through it.
Headphone Level Control
Headphone Jack
Accepts headphones with 1/4” plug
Headphone CUE/PGM Control Allows you to listen simultaneously or separately to the CUE material or the active program
ECHO Level Control Controls the depth of the echo effect
ECHO Repeat Control Lets you control the time period during which the echo is repeated
ECHO Delay Control Lets you adjust the delay time for the echo
ECHO On/Off Switch
Zone Level Control Lets you control the mixer’s overall ZONE volume level, if you set up remote speakers or DJ booth monitors
Zone Mono/Stereo Selector
Zone Balance Control
Master Level Control Lets you control mixer’s overall volume level
Master Mono/Stereo Selector
Master Balance Control
Channel Assign Switch Lets you select the input source to be mixed by the Crossfade Slider Control
Crossfade Slider Control Allows you to smoothly switch between the input sources assigned to Channel A and Channel B
Features and Controls: PYD1930 Mixer
MIC 1 Combo Input Jack For connecting a balanced or unbalanced low impedance microphone with XLRtype or 1/4” plug
MIC 2 Input Jack (on input panel)
For connecting a balanced or unbalanced low impedance microphone with 1/4” plug
MIC Frequency Kill Switches Allows you to kill the selected frequency range instantly for interesting effects. LED lights to indicate kill is activated.
MIC Talkover Allows you to lower the level of the input sources so you can talk them using the DJ Mic
MIC1/2 Level Controls Lets you control the MIC levels as they enter the mix
MIC1/2 Tone Controls
Channel Gain Control Lets you adjust the gain of the input source
Channel Input Selector Lets you choose the input source to play for each channel
Channel CUE Switch Allows you to monitor the selected audio input source and prepare it prior to mixing it in.
Dual Display Meter Indicates the levels of Left and Right Master
Channels
Master Level Control Lets you control mixer’s overall volume level
Master Mono/Stereo Selector
Master Balance Control
10-Band Equalizer Allows you to tailor the mixer output to suit your taste or performance environment. Each frequency range can be cut or boost by up to 10dB.
BNC Lamp Adaptor Allows you to connect a 12V/3W lamp to light the panel
Power Switch and LED
Indicator
Equalizer On/Off Switch
Effect Switch (Send/Receive) Lets you connect a sound effect device, such as reverb, sampler, etc. and either play the signal from it or play another input through it.
Headphone Level Control
Headphone Jack
Accepts headphones with 1/4” plug
Headphone CUE/PGM Control Allows you to listen simultaneously or separately to the CUE material or the active program
Zone Balance Control
Zone Mono/Stereo Selector
Zone Level Control Lets you control the mixer’s overall ZONE volume level, if you set up remote speakers or DJ booth monitors
Sound Effect CUE Switch Lets you monitor the selected sound effect before mixing it in
Sound Effect Volume Control Lets you control the volume level of the sound effect within the mix
Sound Effect Speed Control Lets you control the pitch of the selected sound effect
Digital Sound Effects Selectors Lets you create special sound performance mixes from the eight preprogrammed special effects
Channel Assign Switch Lets you select the input source to be mixed by the Crossfade Slider Control
Crossfade Slider Control Allows you to smoothly switch between the input sources assigned to Channel A and Channel B
2 – Pyle Pro Mixer Owner’s Manual |
Pyle Pro Mixer Owner’s Manual – 3 |