Size:
1.9 Mb
Download

Model No. 831.29623.0

Serial No.

Serial Number

Decal

Assembly

Operation

Maintenance

Part List and Drawing

CAUTION

Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference.

TREADMILL EXERCISER

User’s Manual

Sears, Roebuck and Co., Hoffman Estates, IL 60179

TABLE OF CONTENTS

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover FULL 90 DAY WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

Note: An EXPLODED DRAWING and a PART LIST are attached in the center of this manual.

2

IMPORTANT PRECAUTIONS

WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons, read the following important precautions and information before operating the treadmill.

1.It is the responsibility of the owner to ensure that all users of this treadmill are adequately informed of all warnings and precautions.

2.Use the treadmill only as described.

3.Place the treadmill on a level surface, with at least eight feet of clearance behind it and two feet on each side. Do not place the treadmill on any surface that blocks air openings. To protect the floor or carpet from damage, place a mat under the treadmill.

4.Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a garage or covered patio, or near water.

5.Do not operate the treadmill where aerosol products are used or where oxygen is being administered.

6.Keep children under the age of 12 and pets away from the treadmill at all times.

7.The treadmill should be used only by persons weighing 250 pounds or less.

8.Never allow more than one person on the treadmill at a time.

9.Wear appropriate exercise clothes when using the treadmill. Do not wear loose clothes that could become caught in the treadmill. Athletic support clothes are recommended for both men and women. Always wear athletic shoes. Never use the treadmill with bare feet, wearing only stockings, or in sandals.

10.When connecting the power cord (see page 10), plug the power cord into a surge suppressor (not included) and plug the surge suppressor into a grounded circuit capable of carrying 15 or more amps. No other appliance should be on the same circuit. Do not use an extension cord.

11.Use only a single-outletsurge suppressor that meets all of the specifications described on page 10. To purchase a surge suppressor, see your local Sears store or call1-800-366-7278and order part number 146148, or see your local electronics store.

12.Failure to use a properly functioning surge suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may change speed, accelerate, or stop unexpectedly, which may result in a fall and serious injury.

13.Keep the power cord and the surge suppressor away from heated surfaces.

14.Never move the walking belt while the power is turned off. Do not operate the treadmill if the power cord or plug is damaged, or if the treadmill is not working properly. (See TROUBLESHOOTING on page 17 if the treadmill is not working properly.)

15.Read, understand, and test the emergency stop procedure before using the treadmill (see OPERATION and ADJUSTEMENT.

16.Never start the treadmill while you are standing on the walking belt. Always hold the handrails or the upper body arms while using the treadmill.

17.The treadmill is capable of high speeds. Adjust the speed in small increments to avoid sudden jumps in speed.

18.The pulse sensor is not a medical device. Various factors, including the user’s movement, may affect the accuracy of heart rate readings. The pulse sensor is intended only as an exercise aid in determining heart rate trends in general.

19.Never leave the treadmill unattended while it is running. Always remove the key and unplug the power cord when the treadmill is not in use.

20.Do not attempt to raise, lower, or move the treadmill until it is properly assembled. (See ASSEMBLY on page 6, and HOW TO FOLD AND MOVE THE TREADMILL on page 16.) You must be able to safely lift 45 pounds (20 kg) to raise, lower, or move the treadmill.

3

21.When folding or moving the treadmill, make sure that the storage latch is fully closed.

22.Inspect and properly tighten all parts of the treadmill regularly.

23.Never insert any object into any opening.

24.DANGER: Always unplug the power cord immediately after use, before cleaning the treadmill, and before performing the main-

tenance and adjustment procedures described in this manual. Never remove the motor hood unless instructed to do so by an authorized service representative. Servicing other than the procedures in this manual should be performed by an authorized service representative only.

25.This treadmill is intended for in-homeuse only. Do not use this treadmill in a commercial, rental, or institutional setting.

WARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons withpre-existinghealth problems. Read all instructions before using. Sears assumes no responsibility for personal injury or property damage sustained by or through the use of this product.

SAVE THESE INSTRUCTIONS

The decals shown have been placed on your treadmill. If a decal is missing, or if it is not legible, call toll-free1-888-533-1333and order a free replacement decal (see the front cover of this manual). Apply the decal in the location shown. Note: The decals are not shown at actual size.

4

BEFORE YOU BEGIN

Thank you for selecting the PROFORM® CROSSWALK 370e treadmill. The CROSSWALK 370e treadmill combines advanced technology with innovative design to help you achieve your fitness goals in the convenience and privacy of your home. And when you’re not exercising, the CROSSWALK 370e treadmill can be folded up, requiring less than half the floor space of other treadmills.

For your benefit, read this manual carefully before

using the treadmill. If you have questions after reading this manual, call1-800-4-MY-HOME® (1-800-469-4663).To help us assist you, please note the product model number and serial number before calling. The model number of the treadmill is 831.29623.0. The serial number can be found on a decal attached to the treadmill (see the front cover of this manual for the location).

Before reading further, please review the drawing below and familiarize yourself with the labeled parts.

 

Bookrack

Accessory Tray

 

Upper Body Arm

Console

 

Handrail

Key/Clip

 

Storage Latch

Upright

 

Reset/Off

Walking Belt

Circuit Breaker

 

 

Power Cord

Foot Rail

 

 

Cushioned Walking Platform

 

for maximum exercise comfort

BACK

 

 

RIGHT SIDE

Rear Roller

 

Adjustment Bolts

 

 

5

ASSEMBLY

Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated withhigh-performancelubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild,non-abrasivecleaner.

Assembly requires the included allen wrenches rubber mallet , and adjustable wrench

and your own phillips screwdriver ,.

For help identifying the assembly hardware, see the drawings below. If a part is not in the parts bag, first check to see if it has been pre-assembled. If a part is missing, calltoll-free1-888-533-1333.

Washer (38)–4

Handrail Star

Star Washer

Wheel Nut (32)–2

Extension Leg

 

Washer (95)–4

 

Nut (46)–4

 

(106)–4

 

 

 

 

 

Silver Ground

1/2” Screw (48)–6

3/4” Screw (2)–6

1” Tek Screw (39)–4

Screw (75)–1

 

 

 

 

 

3 1/2” Bolt (45)–4

 

Extension Leg Bolt (93)–4

Handrail Bolt (37)–4

 

Wheel Bolt (64)–2

1. Make sure that the power cord is unplugged.

1

 

 

 

With the help of a second person, carefully tip the

 

57

 

 

treadmill onto its left side as shown. Partially fold the

69

 

Frame (86) so the treadmill is more stable. Do not fully

93

 

fold the treadmill until it is completely assembled.

 

Insert an Extension Leg (63) into the base of the

 

39

Uprights (69) with the Base Pad (61) oriented as shown.

 

 

 

If necessary, tap on the Extension Leg with a rubber mal-

 

 

let. Next, hold two Extension Leg Nuts (46) in the bottom

 

39

of the Extension Leg, and insert two Extension Leg Bolts

63

46

(93) into the top of the Extension Leg. Firmly tighten the

61

 

Extension Leg Bolts into the Extension Leg Nuts.

 

 

86

 

Attach two Base Pads (57) to the base of the Uprights

 

 

(69) with two 1” Tek Screws (39).

 

 

6

2.Attach a Wheel (66) to the base of the Uprights (69) with a Wheel Bolt (64) and a Wheel Nut (32) as shown. Do not overtighten the Bolt; the Wheel should turn freely.

With the help of a second person, carefully tip the treadmill onto its other side. See assembly steps 1 and 2, and attach the other Extension Leg (63), Base Pads (57), and Wheel (66).

With the help of a second person, carefully lower the base of the Uprights (69) to the floor so the Uprights are in the vertical position.

3.Identify the Right Handrail (72), which has a large hole in the left side. Remove the wire tie holding the Upright Wire (42) inside the right Upright (69). Feed the Upright Wire into the hole in the bottom of the Right Handrail and out of the large hole in the side. Note: It may be helpful to use needlenose pliers to pull the Wire Harness out of the hole.

Set the Right Handrail (72) on the right Upright (69). Attach the Right Handrail with two Handrail Bolt (37) and two Handrail Star Washers (95). Be careful not to pinch the Upright Wire (42).

Attach the Left Handrail (71) as described above. Note: There is not an upright wire on the left side.

4.Hold the Console Base (47) near the Left Handrail (71). Attach the end of the ground wire on the Console Base to the indicated small hole in the Left Handrail with the Silver Ground Screw (75).

7

2

 

64

 

 

 

69

66

 

 

 

 

32

3

 

 

37

71

 

 

 

95

 

95

 

 

 

37

Hole

 

42

 

 

95

 

 

72

 

 

 

69

4

 

 

Ground

Wire

47

Small

Hole

75

71

5.Touch the Right Handrail (72) to discharge any static.

Slide the sleeve off the connector on the Upright Wire (42) as shown in the inset drawing. Next, press the end of the Upright Wire into the socket in the bottom of the Console Base (47). The connector should slide easily into the socket and snap into place. If the connector does not slide easily and snap into place, turn the connector and then insert it. Then, slide the sleeve back over the connector.

6.Set the Console Base (47) on the Handrails ( 71, 72). Attach the Console Base with four 3/4” Screws (2). Start all four Screws before tightening them; do not overtighten the Screws.

See the lower drawing. Make sure that the Upright

Wire (42) is routed below the two indicated round posts (A). Next, press the Upright Wire into the slot between the square post (B) and the Console Base (47).

7.Cover the Upright Wire (42) with the Right Grip Plate (36). Be careful not to pinch the Upright Wire. Tighten three 1/2” Screws (48) into the Right Grip Plate and the Console Base (47).

Attach the Left Grip Plate (32) over the ground wire and the other wires with three 1/2” Screws (48). Be careful not to pinch any of the wires.

5

 

 

72

 

 

 

 

42

 

 

47

 

Sleeve

Connector

42

 

 

6

 

47

 

 

72

 

71

2

 

 

 

 

2

 

A

 

 

 

B

42

47

 

7

 

47

 

 

Ground

 

 

Wire

 

 

42

 

36

32

 

 

48

 

48

 

 

8

8.Attach the Left Upper Body Arm (24) to the left Upright (69) with two 3 1/2” Bolts (45), two Washers (38), and two Star Washers (106) as shown. Make sure that the

Left Upper Body Arm is on the indicated side of the Console Base (47).

Attach the Right Upper Body Arm (not shown) to the right Upright (not shown) in the same way.

9.Attach the Latch Housing (29) to the left Upright (69) with two 3/4” Screws (2). Make sure that the large hole in the Latch Housing is on the side shown.

Remove the knob from the pin. Make sure that the collar and the spring are on the pin as shown. Insert the pin into the Latch Housing (29), and tighten the knob back onto the pin.

8

47

24

69

106

38

106

45

9

29

Knob

2

Large

Hole

69

Spring

Collar

Pin

10.Make sure that all parts are properly tightened before you use the treadmill.Note: Extra hardware may be included. Keep the included allen wrenches in a secure place; the large allen wrench is used to adjust the walking belt (see page 17). To protect the floor or carpet, place a mat under the treadmill.

9

OPERATION AND ADJUSTMENT

THE PRE-LUBRICATEDWALKING BELT

Your treadmill features a walking belt coated with highperformance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or the walking platform. Such substances will deteriorate the walking belt and cause excessive wear.

HOW TO PLUG IN THE POWER CORD

DANGER: Improper connection of theequipment-groundingconductor can result in an increased risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with theproduct—ifit will not fit the outlet, have a proper outlet installed by a qualified electrician.

Your treadmill, like any other type of sophisticated electronic equipment, can be seriously damaged by sudden voltage changes in your home’s power. Voltage surges, spikes, and noise interference can result from weather conditions or from other appliances being turned on or off. To decrease the possibility of your treadmill being damaged, always use a surge suppressor with your treadmill (see drawing 1 at the right). To purchase a surge suppressor, see your local Sears store or call 1-800-366-7278 and order part number 146148, or see your local electronics store.

Use only a single-outletsurge suppressor that is UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a UL suppressed voltage rating of 400 volts or less and a minimum surge dissipation of 450 joules. The surge suppressor must be electrically rated for 120 volts AC and 15 amps. There must be a monitoring light on the surge suppressor to indicate whether it is functioning properly. Failure to use a properly functioning surge suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may change speed, accelerate, or stop unexpectedly, which may result in a fall and serious injury.

This product must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having

an equipment-groundingconductor and a grounding plug.Plug the power cord into a surge suppressor, and plug the surge suppressor into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. Important: The treadmill is not compatible with GFCI-equipped outlets.

This product is for use on a nominal 120-voltcircuit, and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that looks like the adapter illustrated in drawing 2 may be used to connect the surge suppressor to a2-polereceptacle as shown in drawing 2 if a properly grounded outlet is not available.

1

Grounded Outlet Box

Surge Suppressor

Grounding Pin

Grounding Pin

Grounded Outlet

Grounding Plug

 

2

Grounded Outlet Box

Adapter

Surge Suppressor

Lug

Metal Screw

The temporary adapter should be used only until a properly grounded outlet (drawing 1) can be installed by a qualified electrician.

The green-coloredrigid ear, lug, or the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used it must be held in place by a metal screw.Some 2-pole receptacle outlet box covers are not grounded. Contact a qualified electrician to determine if the outlet box cover is grounded before using an adapter.

10