Procom SFE23RE-C, SFE33RE-O, SFE33RE-C, SFE33RE-DO, SFE23RE-DO User Manual

...
0 (0)
Procom SFE23RE-C, SFE33RE-O, SFE33RE-C, SFE33RE-DO, SFE23RE-DO User Manual

PRO-COM

SFE23RE-W SFE33RE-W SFE23RE-C SFE33RE-C SFE23RE-O SFE33RE-O SFE23RE-DO SFE33RE-DO

SFE23RE SHOWN

Freestanding

Electric Fireplace

Installation Instructions and Owner’s Manual

WARNING! IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY, A FIRE MAY RESULT CAUSING PROPERTY, PERSONAL INJURY OR LOSS OF LIFE.

FOR YOUR SAFETY

DO NOT STORE

OR USE GASOLINE OR OTHER

FLAMMABLE VAPORS OR LIQUIDS

IN THE VICINITY OF THIS OR ANY

OTHERAPPLIANCE

ANSI/UL1278. MOVABLE AND WALL-OR CEILING HUNG ELECTRIC ROOM HEATERS

INSTALLER: DO NOT DISCARD THIS MANUAL-LEAVE FOR HOME OWNER

1

PC-FE23A610-0506

TABLE OF CONTENTS

PLEASE READ THE INSTALLATION & OPERATION INSTRUCTIONS

BEFORE USING THIS APPLIANCE

WEARE PLEASED THAT YOU HAVE CHOSEN TO PURCHASEAN ELECTRIC FIREPLACE MANUFACTURED BY NANJING PRO-COM ELECTRICAPPLIANCE CO., LTD

IMPORTANT: Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible electric shock, fire hazard and will void the warranty.

Important Instructions ….…………………………………………………………

....2

Locating Your Electric Fireplace…………………………………….………….......

3

Clearance To Combustibles………………………………………….…………......

3

Electrical Connections…..……………………………………………….……….....

3

Electrical Specifications…………………………………………...……………......

3

Service Instructions…………………………………………………………….…......

3

Replacing Light Bulbs…………………………………….……………………........

3

Maintenance of Motors………………………………………...........

…………….…4

Glass Information……………………………………………...........

………………..4

Electrical Wiring Diagram……………………………………........

………….......

…4

Operating Instructions………………………………………………………....…........

5

Specification........………………………………………………………………...........

7

Replacement Parts..……………………………………………………........

7

Replacement Parts List........................

……………………………………………..8

Installing decorating logs..……………………………………………………........

9

21

IMPORTANT INSTRUCTIONS

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

1.Read all instructions before using this heater.

2.This appliance is hot when in use. To avoid burns, do not come in contact with heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet(1m.) from the front of the heater.

3.Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.

4.Always unplug heater when not in use.

5.Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner.

6.Any repairs to this appliance should be carried out by a qualified service person.

7.Under no circumstances should this electric fireplace be modified. Parts having to be removed for servicing must be replaced prior to operating this electric fireplace again.

8.Do not use outdoors.

9.This heater is not intended for use in bathrooms, laundry areas or similar indoor locations. Never use this appliance near a bathtub or other water container.

10.Do not run cord under carpeting. Do not cover cord with throw rugs, runners or similar coverings. Arrange cord away from traffic areas and where it will not be tripped over.

11.To disconnect heater, turn controls to OFF, then remove plug from outlet.

12.Connect to properly grounded outlets only.

13.When this appliance is installed, it must be electrically grounded in accordance with local codes with the current CSA C22.1 Canadian local codes for USA installations. Follow local codes and National Electrical Code, ANSI/NFPA NO.70 and Canadian Cord: CZ 22.2 NO.0.

14.Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause electric shock, fire or damage to the heater.

15.To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, such as a bed, where openings may become blocked.

16.This heater gets hot and it contains internal parts that sparks and arcs. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.

17.Use this heater only as described in this manual. Other uses not recommended by the manufacturer may cause fire, electric shock, or injury.

18.Avoid the use of an extension cord because it may overheat and cause a risk of fire. However if you must use an extension cord, the cord shall be No. 14AWG minimum size and rated not less than 1900 watt. The extension cord must be a three wire cord with grounding type plug and cord connector.

19.This electric fireplace heater should not be used as a drying rack for clothing. Also, do not hang Christmas stockings or decorations on or near it.

20.SAVE THESE INSTRUCTIONS.

23

LOCATING YOUR ELECTRIC FIREPLACE

Your new freestanding electric fireplace may be installed vir-

tually anywhere in your home. However when choosing a

location for your new electric fireplace, ensure that the gen-

eral instructions are followed. For best effect results, install

the electric fireplace out of direct sunlight.

CLEARANCE TO COMBUSTIBLES

Sides....................................

0 mm 0 inches

Floor.....................................

0 mm 0 inches

Top........................................

0 mm 0 inches

ELECTRICAL CONNECTION

A 15 AMP, 120 Volt,60Hz circuit with a properly grounded outlet is required. Preferably, the fireplace will be on a dedicated circuit. Other appliances on the same circuit may cause the circuit breaker to trip or the fuse to blow when the heater is on operation. The unit comes standard with a 6’ (1828mm) long three wire cord exiting from the rear of the fireplace. Plan the installation to avoid the use of an extension cord. If an extention cord must be used, it must be a minumum 14 AWG three wire with grounding type plug connector and rated no less than 1900 Watts.The cord shall not be more than 20 feet in length.

WARNING: Electrical outlet wiring must comply with local building codes and all other appliable regulations to reduce the risk of fire, electrical shock and injury.

WARNING: Do not use this fireplace if any part of it has been under water. Immediatly call a quilified service technitian to inspect the fireplace and replace any part of the electrical system if necessary.

ELECTRICAL SPECIFICATIONS

Voltage:

120 VAC, 60 Hz

Total Amps:

11.5 Amps

Total Watts:

1380 Watts

Heater Rating:

1200 Watts

SERVICE INSTRUCTIONS

WARNING: Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire, electrical shock or personal injury.

REPLACING LIGHT BULBS

This fireplace uses four clear 120 Volt, 60 Watt, E- 12 socket base light bulbs (small base, chandelier candle type).The 60 Watt bulbs are located under the log set/ember bed. For convenience, if one of the bulbs burns out, it may be a good idea to replace all of the light bulbs.

1.Turn off power to the unit by unplugging the power cord.

2.Let fireplace cool if it has been operating.

3.Remove the two screws on the top corner of screen. Pull the screen upward slightly, and then pull out.

4.Remove the four screws that secure the log set/ember bed in position.

5.Remove log set / ember bed and grate assembly.

6.Examine the bulb(s) to determine which bulbs need to be replaced.

7.While holding the socket, unscrew defective bulb(s) counterclockwise.

8.Install the new light bulb(s) by holding the socket and screwing clockwise.

9.Reinstall the log set/ember bed, grate assembly and screen. Follow the above procedure in reverse order.

WARNING: Do not exceed 60 Watts per bulb. The use of higher rated bulbs may result in a fire causing property damage and personal injury.

43

Loading...
+ 7 hidden pages