Jazzy Select 14 INFINFB2048
BASIC TROUBLESHOOTING INSTRUCTIONS: JAZZY SELECT 14
Any electromechanical device requires occasional troubleshooting. However, most problems that arise can usually
be solved with a bit of thought and common sense. Many of these problems occur because the batteries are not fully
charged or because the batteries are worn down and can no longer hold a charge. Below are a series of basic
troubleshooting instructions for the Jazzy Select 14 Power Chair . This information is to be used as a supplement to
the troubleshooting instructions provided in the owner’s manual. If you have any questions about this information,
contact your authorized Pride Provider.
What if the systems on my Jazzy Select 14 seem to be “dead” (controller does not light up when the on/off
key is pressed)?
! Make sure the batteries are wired properly—refer to the battery wiring diagram located on the power base.
! Make sure the connections on the battery terminals are tight and secure.
! Make sure the battery quick-disconnect harness connections are fully joined.
! Make sure the main circuit breaker has not tripped—push in the main circuit breaker reset button.
! Make sure the controller is completely connected to the power base.
What if the range per charge of my Jazzy Select 14 diminishes over time?
! Determine if the batteries have ever been replaced. Batteries over a year old may be defective.
! Determine how frequently you charge the batteries in comparison to how often you use the power chair.
If you use your power chair on a daily basis, you should charge the batteries every day for 8-14 hours.
! Determine when the batteries were last charged. Even if the power chair has not been in use, the batteries
should be charged once a week for 12-14 hours.
! Determine how long you let the batteries charge. It takes 8-14 hours to fully charge a depleted set of
batteries; continual undercharging reduces the overall life of the batteries.
! Observe the ammeter during battery charging to determine if the batteries are receiving a charge. If the
ammeter does not go up when the battery charger is plugged into the charger power cord receptacle and an
electrical outlet, the batteries are not getting charged. Check the charger fuse and ensure the electrical outlet is
good.
! Determine if a wall switch controls the electrical outlet used for battery charging. If a wall switch does
control the outlet and the switch is turned off inadvertently , the batteries will not fully char ge.
! Is an extension cord being used to connect the battery charger to the electrical outlet? Pride prohibits the
use of an extension cord when charging the batteries. The charger should be plugged directly into a properlywired standard electrical outlet as the length and condition of the extension cord can have an adverse affect on
the battery charger.
! Determine how far you let the battery condition meter LEDs go down before charging the batteries. If
you continually allow the battery condition meter LEDs to fall into the red area, the overall life of the batteries
will be reduced.
What if my Jazzy Select 14 is operating slower than it has in the past?
! Determine when the batteries were last charged. When the battery charge gets low, the batteries supply less
power to the motors, which causes the motors to spin slower.
! Determine the temperature of the power chair at the time the problem occurred. The Jazzy Select 14
electrical system will protect itself from overheating when its internal temperature gets too high by reducing the
amount of power sent to the motors. When this happens, the power chair will gradually slow to a stop. Allow
the power chair to cool down and it will resume normal operation.
1 www.pridemobility.com INFINFB2048/Rev A/11-29-06
BASIC TROUBLESHOOTING INSTRUCTIONS: JAZZY SELECT 14
What if my Jazzy Select 14 begins pulling to one side?
! Determine if the joystick is being deflected straight or at a slight angle. Even a small amount of deflection
right or left will cause the chair to veer over a long distance.
! Determine if both manual freewheel levers are in the drive position. If only one manual freewheel lever is
in the drive position, the other motor will not operate and the Jazzy Select 14 will veer severely .
! Determine if both tires are inflated to the proper psi if the power chair is equipped with pneumatic tires.
Pneumatic tires should be inflated to 35 psi (2.4 bar). If one tire is inflated more than the other, the power chair
will pull to the side that is underinflated.
What if the Jazzy Select 14 powers up, but will not move?
! Determine if both manual freewheel levers are in the freewheel position. If the power chair is in freewheel
mode, then the electronics will function but the motors will not spin the wheels.
! Determine if the controller is flashing a fault code. The Jazzy Select 14 comes equipped with a VSI or VR2
controller . Both controllers will flash a code via the battery condition meter LEDs if a system fault is detected.
VSI DIAGNOSTIC FLASH CODES
# OF LEDS CODE CAUSE POSSIBLE SOLUTION
One red LED 1 Low battery voltage Charge batteries
Two red LEDs 2 Left motor open Make sure left motor is plugged into controller.
Three red LEDs 3 Left motor wiring fault Contact your authorized Pride Provider.
Three red LEDs 4 Right motor open Make sure right motor is plugged into controller.
One yellow LED
Three red LEDs 5 Right motor wiring fault Contact your authorized Pride Provider.
Two yellow LEDs
Three red LEDs 6 Inhibit active Contact your authorized Pride Provider.
Three yellow LEDs
Three red LEDs 7 Joystick error Contact your authorized Pride Provider.
Four yellow LEDs
Three red LEDs 8 Controller error Contact your authorized Pride Provider.
Four yellow LEDs
One green LED
Three red LEDs 9 Brake fault Make sure both motors are plugged into controller .
Four yellow LEDs
Two green LEDs
Three red LEDs 10 High battery voltage Contact your authorized Pride Provider.
Four yellow LEDs
Three green LEDs
INFINFB2048/Rev A/11-29-06 www.pridemobility.com 2
Loading...