Size:
851.82 Kb
Download

 

 

ESPAÑOL: PÁGINA 11

 

 

FRANÇAISE : PAGE 23

 

 

 

Instruction

BRAD NAILER

manual

 

 

To learn more about Porter-Cablevisit our website at:

http://www.porter-cable.com

Copyright © 2000 Porter-CableCorporation

MODEL BN200A

IMPORTANT

Please make certain that the person who is to use this equipment carefully reads and understands these instructions before starting operations.

The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference.

Model No. ______________________________________

Type ___________________________________________

Serial No. _______________________________________

Part No. 894884-003

GB ENGLISH

EC-DECLARATIONOF CONFORMITY

We declare under our sole responsibility that this product is in conformity with the regulations 98/37/EEC.

Matthew G. Popik

Vice President of Engineering

IMPORTANT SAFETY INSTRUCTIONS

WARNING: When using pneumatic tools, basic safety precautions should always be followed to reduce the risk of personal injury, including the following:

READ AND FOLLOW ALL INSTRUCTIONS.

There are certain applications for which this tool was designed. Porter-Cablestrongly recommends that this tool NOT be modified and/or used for any application other than for which it was designed. If you have any questions relative to its application DO NOT use the tool until you have written PorterCable and we have advised you.

1.USE SAFETY GLASSES. To prevent eye injuries, the tool operator and all persons in the work area must wear safety glasses with permanently attached, rigid, plastic side shields. These safety glasses must conform to ANSI Z87.1 requirements (approved glasses have “Z87” printed or stamped on them). Fig. 1.

2.WEAR EAR PROTECTION to safeguard against possible hearing loss. Fig. 1.

3.USE CLEAN, DRY, REGULATED compressed air at 70 to 120 PSI, (4.8 to 8.3 BAR). Fig. 2.

4.DO NOT CONNECT TOOL TO pressure which potentially exceeds 200 PSI (13.7 BAR).

Technical Service Manager

Porter-CableCorporation

4825 Highway 45 North

P. O. Box 2468

Jackson, TN 38302-2468

Fig. 1

Fig. 2

5.ONLY USE AIR HOSE THAT IS RATED for a maximum working pressure of 150 PSI or 150% of the maximum system pressure, which ever is greater.

6.NEVER USE OXYGEN, CARBON DIOXIDE, combustible gases or any other bottled gas as a power source for this tool: explosion and serious personal injury could result. Fig. 3.

7.CONNECT TOOL TO AIR SUPPLY HOSE with a coupling that removes all pressure from the tool when the coupling is disconnected. Fig. 4.

Fig. 3

Fig. 4

2

8.DISCONNECT TOOL FROM AIR

SUPPLY HOSE before doing tool maintenance, clearing a jammed fastener, leaving work area, moving tool to another location, or handing the tool to another person. Fig. 5.

9.NEVER USE A TOOL that is leaking air, has missing or damaged parts, or requires repair. Make sure all screws and caps are securely tightened. Fig. 5.

10.NEVER USE TOOL IF SAFETY, trigger or springs are inoperable, missing or damaged. Do not alter or remove safety, trigger, or springs. Make daily inspections for free movement of trigger and safety mechanism. Fig. 5.

Fig. 5

Fig. 6

11.DO NOT USE TOOL WITHOUT SAFETY WARNING LABEL. If label is missing, damaged or unreadable, contact your Porter-Cable Service Center for a replacement. Fig. 6.

12.ONLY USE PARTS, FASTENERS, AND ACCESSORIES recommended by PorterCable. Fig. 7.

13.CONNECT TOOL TO AIR SUPPLY BEFORE loading fasteners, to prevent a fastener from being fired during connection. The tool driving mechanism may cycle when tool is connected to the air supply. Fig. 8.

14.ALWAYS ASSUME THE TOOL CONTAINS FASTENERS. Keep the tool pointed away from yourself and others at all

times. No horseplay. Respect the tool as a working implement.

15. DO NOT LOAD FASTENERS with trigger or safety depressed, to prevent unintentional firing of a fastener. Fig. 9.

Fig. 7

Fig. 8

Fig. 9

3

Fig. 10

16. REMOVE FINGER FROM TRIGGER when not driving fasteners. Never carry tool with finger on trigger: tool may fire a fastener if safety is bumped while trigger is depressed. Fig. 10.

17.DON’T OVERREACH. Keep proper footing and balance at all times when using or handling the tool. Fig. 11.

18.FIRE FASTENERS INTO WORK

SURFACE ONLY: never into materials too hard to penetrate. Fig. 12.

19.GRIP TOOL FIRMLY TO MAINTAIN CONTROL WHILE allowing tool to recoil away from work surface as fastener is driven. If safety element is allowed to recontact work surface before trigger is released, an unwanted fastener may be fired.

20.DO NOT DRIVE FASTENERS on top of other fasteners, or with the tool at too steep

an angle: the fasteners can ricochet causing personal injury. Fig. 13.

21.DO NOT DRIVE FASTENERS CLOSE to the edge of the workpiece. The workpiece is likely to split allowing the fastener to fly free or ricochet causing personal injury. Fig.

22.KEEP HANDS AND BODY PARTS away from area shown in Fig. 13A, to avoid

injury.

23. DO NOT USE ON SCAFFOLDINGS OR LADDERS or for tasks in which changing location involves the use of scaffoldings, stairs, ladders, and the like. Do not use for specific tasks such as closing boxes or crates or fitting transportation safety systems on vehicles and wagons. Fig. 13B.

Fig. 11

Fig. 12

Fig. 13

Fig. 13A

Fig. 13B

4

TECHNICAL SPECIFICATIONS

Noise level . . . . . . . . . . . . . . .

. . . . . . Typical Mean

 

A - Weighted sound impulse

. . . . . . effective Acceleration . . . . . . .

2.5 m/s2

power level . . . . . . . . . .

99 dBA

 

P - Emission sound

 

 

pressure level . . . . . . . .

86 dBA

 

EMPLOYER’S RESPONSIBILITIES

Employer must enforce compliance with the safety warnings and all other instructions contained in this manual.

Keep this manual available for use by all people assigned to use this tool.

For personal safety and proper operation of this tool, read and follow all of these instructions carefully.

OPERATING INSTRUCTIONS

FOREWORD

Porter-CableModel BN200A is a heavy duty pneumatic brad nailer. It is designed to install 18 ga. brad nails of various lengths (from3/4" to 2" long), see ACCESSORIES Listing in back of this manual.

CAUTION: Use approvedPorter-Cablebrad nails only (see ACCESSORIES Listing in back of this manual).

POWER SOURCE

This tool is designed to operate on clean, dry, compressed air at regulated pressures between 70 and 120 PSI (Pounds per Square Inch). The preferred system would include a filter, a pressure regulator, and an automatic oiler located as close to the tool as possible (within 15 feet is ideal).

All compressed air contains moisture and other contaminates that are detrimental to internal components of the tool. An air line filter will remove most of these contaminates and significantly prolong the life of the tool. If an in-lineoiler is not available: place five or six drops ofPorter-CableAir Tool Oil (see ACCESSORIES), into the tool’s air inlet at the beginning of each workday.

The tool is equipped with a male “quick connector”. The tool must always be connected to the air supply with a coupling such that all pressure is removed from the tool when the coupling is disconnected.

CAUTION: All air line components (hoses, connectors, filters, regulators, etc.) must have a minimum working pressure rating of 150 PSI (10.3 BAR) or 150% of maximum system potential, whichever is higher.

Do not connect this tool to a system with maximum potential pressure greater than 200 PSI, (13.7 BAR).

Only connect tool to air supply with a coupling that will release all pressure from the tool when disconnected.

Disconnect tool from air supply before performing maintenance, clearing a jammed fastener, leaving work area, moving tool to another location, or handing the tool to another person.

5

Fig. 14

Fig. 15

1

2

Fig. 16

Fig. 17

PREPARING THE TOOL

1. After reading and understanding this entire manual, connect tool to air supply.

CAUTION: Keep tool pointed away from yourself and others at all times.

Always connect tool to air supply before loading fasteners. Do not load fasteners with trigger or safety depressed.

Only use approved Porter-Cablefasteners (see ACCESSORIES).

Always wear Z87 approved safety glasses, and hearing protection when preparing or operating the tool.

Never use a tool that leaks air or needs repair.

2.Depress latch and slide magazine cover open, see Fig. 15.

3.Insert a strip of approved fasteners, see Fig. 16. Orient fasteners with points down, and in contact with the bottom of the magazine.

4.Push magazine cover closed, see Fig. 17.

5.Adjust directional exhaust deflector (A) Fig.

18, so that the exhaust air blast will be directed

 

A

away from the operator. The exhaust deflector

 

 

 

provides 8 detented positions for directing the

 

 

exhaust blast away from the operator. Grasp the

 

 

deflector and rotate it to the desired position for

 

 

the current application.

 

 

 

Fig. 18

6

Fig. 19

USING THE TOOL

Complete all steps of PREPARING THE TOOL before using the tool.

To fire, grip tool firmly, position nose of tool onto work surface, push forward on tool to depress safety, and squeeze trigger to fire a fastener. This “trigger fire” method provides the most accurate fastener placement. This tool is shipped from the factory with a “restrictive fire trigger” that only allows the tool to be fired this way and is less likely to fire an unwanted fastener.

An alternate “bottom fire trigger” is available. The “bottom fire” trigger allows the tool to be fired in two different ways.

1.The tool can be fired using the “trigger fire” method described above.

OR

2. Grip tool firmly, depress and hold trigger while pushing the tool firmly against work surface. The tool will fire a fastener each time the safety is depressed. This method is known as “bottom fire” and allows very fast repetitive fastener placement.

The “bottom fire trigger” is available free-of-chargeby calling1-800-321-9443in the United States and Canada or001-901-660-9374outside the United States and Canada, and providing tool model and serial number. For identification purposes: the Bottom Fire Trigger is black and the Restrictive Fire Trigger is red.

CAUTION: Remove finger from trigger when not driving fasteners. Never carry tool with finger on trigger: tool may fire a fastener if safety is bumped.

Keep tool pointed in a safe direction at all times.

Never attempt to drive a fastener into material that is too hard, or at too steep an angle, or near the edge of the workpiece. The fastener can ricochet causing personal injury.

Disconnect tool from air supply before performing maintenance, clearing a jammed fastener, leaving work area, moving tool to another location, or handing the tool to another person.

Clean and inspect tool daily. Carefully check for proper operation of trigger and safety mechanism. Do Not use the tool unless both the trigger and the safety mechanism are functional, or if the tool is leaking air or needs any other repair.

The depth to which a fastener is driven is controlled by the depth adjustment knob (A) Fig. 19. The depth of drive is factory adjusted to a nomimal setting. Test fire a fastener and check depth. If a change is desired, rotate the adjustment knob (A) Fig. 19: the adjustment knob has detents every 1/4

turn. Rotate the knob clockwise (see A Fig. 19), to increase the depth of drive,

rotate the knob counterclockwise to decrease the depth of drive. Test fire another fastener and check depth. Repeat as necessary to achieve desired results. The amount of air pressure required will vary depending on the size of the fastener and the material being fastened. Experiment with the air pressure setting to determine the lowest setting that will consistently perform the job at hand. Air pressure in excess of that required can cause premature wear and/or damage to the tool.

7

Fig. 20

 

Fig. 21

 

 

 

CLEARING A JAMMED FASTENER

1.CAUTION: Disconnect tool from air supply.

2.Open magazine and remove any remaining fasteners.

CAUTION: Remove fasteners from tool before opening the fastener guide plate. Fasteners are under pressure and may shoot out of magazine which could cause injury.

3.Depress the quick release latch and open the fastener guide plate (see Fig. 20).

4.Remove the jammed fastener (see Fig. 21).

5.Depress the quick release latch, close the fastener guide plate, and release the latch.

NOSE CUSHION

 

 

This tool is equipped with a rubber

 

 

nose cushion (A) Fig. 22, that

 

 

prevents marring of finished surfaces

 

 

by the metal safety during normal

 

 

operation. The nose cushion can be

 

 

removed and stored in the rear area

 

 

of the magazine (B) Fig. 22, when it is

 

 

not required.

 

 

CAUTION: Disconnect tool from

B

A

air supply before removing or

Fig. 22

reinstalling rubber nose cushion.

MAINTENANCE

CLEAN AND INSPECT DAILY

CAUTION: Disconnect tool from air supply before cleaning and inspection.Correct all problems before placing the tool back in use.

Wipe tool clean and inspect for wear or damage. Use non-flammablecleaning solutions to wipe exterior of tool only if necessary. DO NOT SOAK tool with cleaning solutions. Such solutions can damage internal parts.

Inspect trigger and safety mechanism to assure system is complete and functional: no loose or missing parts, no binding or sticking parts.

Keep all screws tight. Loose screws can cause personal injury or damage tool.

If tool is used without an in-lineoiler: place 5 or 6 drops ofPorter-CableAir Tool Oil into the air inlet of the tool at the beginning of each workday.

8

SERVICE AND REPAIRS

All quality tools eventually require servicing or replacement of parts due to wear from normal use. Some user serviceable components are described in the TROUBLESHOOTING Section. Complete product Service is available from either an AUTHORIZED PORTER-CABLESERVICE STATION or aPORTER-CABLESERVICE CENTER. All repairs made by these agencies are fully guaranteed against defective material and workmanship. We cannot guarantee repairs made or attempted by anyone other than these agencies.

Should you have any questions about your tool, feel free to write us at any time. In any communications, please give all information shown on the nameplate of your tool (model number, type, serial number, etc.).

TROUBLESHOOTING

CAUTION: Disconnect tool from air supply before performing any Service Procedure.

SYMPTOM

PROBLEMS

SOLUTIONS

1.Air leak near top of tool or in trigger area.

Loose screws.

Tighten screws.

Worn or damaged

Install “OVERHAUL” Maintenance Kit.

o-ringsor seals.

 

2.Tool does nothing or operates sluggishly.

Inadequate air supply.

Verify adequate air supply.

Inadequate lubrication.

Put 5 or 6 drops of oil into air inlet.

Worn or damaged

Install “DRIVER” Maintenance Kit.

o-ringsor seals.

 

3.Air leak near bottom of tool.

Loose screws.

Tighten screws.

Worn or damaged

Install “OVERHAUL” Maintenance Kit.

o-ringsor bumper.

 

4.

Tool jams frequently. Incorrect fasteners.

Verify approved fasteners of

 

 

correct size.

 

Damaged fasteners.

Replace w/undamaged fasteners.

 

Magazine or nose

Tighten screws.

 

screws loose.

 

 

Magazine is dirty.

Clean magazine.

 

Driver is worn or damaged.

Install “DRIVER” Maintenance Kit.

 

 

 

5.

Other.

Contact a Porter-Cable

 

 

Service Facility.

9

ACCESSORIES

The testing of this tool has been accomplished with the following accessories. For safest operation, it is recommended that only these accessories be used with this product.

WARNING: Since accessories other than those listed have not been tested with this product, use of such accessories could be hazardous.

CATALOG NO.

DESCRIPTION

LENGTH

GAUGE

QUAN/BOX

BN18075

18

Ga. Brad Nail, 3/4"

3/4"

18

5000

BN18075-1

1000 Pk. of BN18075

3/4"

18

1000

BN18100

18

Ga. Brad Nail, 1"

1"

18

5000

BN18100-1

1000 Pk. of BN18100

 

18

1000

BN18119

18

Ga. Brad Nail, 13/16"

13/16"

18

5000

BN18125

18

Ga. Brad Nail, 11/4"

11/4"

18

5000

BN18125-1

1000 Pk. of BN18125

 

18

1000

BN18150

18

Ga. Brad Nail, 11/2"

11/2"

18

5000

BN18156

18

Ga. Brad Nail, 19/16"

19/16"

18

5000

BN18175

18

Ga. Brad Nail, 13/4"

13/4"

18

5000

BN18200

18

Ga. Brad Nail, 2"

2"

18

5000

60061

“OVERHAUL” Maintenance Kit

 

 

60063

“DRIVER” Maintenance Kit

 

 

884293

Oil (for Air Tools)

 

 

 

893579

Safety Glasses

 

 

 

893933

Bottom Fire Trigger

 

 

 

PORTER-CABLELIMITED

ONE YEAR WARRANTY

Porter-Cablewarrants its nailing and stapling tools for a period of one year from the date of original purchase. We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material during the warranty period. For repair or replacement return the complete tool or accessory, transportation prepaid, to your nearestPorter-CableService Center or Authorized Service Station. Proof of purchase may be required. This warranty does not apply toO-ringsand Driver Blades or to repair or replacement required due to misuse, abuse, normal wear and tear or repairs attempted or made by other than our Service Centers or Authorized Service Stations.

ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE OF PURCHASE.

To obtain information on warranty performance please write to: PORTER-CABLECORPORATION, 4825 Highway 45 North, P.O. Box 2468, Jackson, Tennessee38302-2468;Attention: Product Service. THE FOREGOING OBLIGATION ISPORTER-CABLE’SSOLE LIABILITY UNDER THIS OR ANY IMPLIED WARRANTY AND UNDER NO CIRCUMSTANCES SHALLPORTER-CABLEBE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state.

10

PORTER-CABLESERVICE CENTERS (CENTROS DE SERVICIO DEPORTER-CABLE)(CENTRE DE SERVICEPORTER-CABLE)

Parts and Repair Service for Porter-CablePower Tools are Available at These Locations (Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros dePorter-Cable)

(Locations où vous trouverez les pièces de rechange nécessaires ainsi qu’un service d’entretien)

ARIZONA

GEORGIA

MINNESOTA

Cleveland 44125

Tempe 85282 (Phoenix)

Forest Park 30297 (Atlanta)

Minneapolis 55429

8001 Sweet Valley Drive

2400 West Southern Avenue

5442 Frontage Road, Suite 112

4315 68th Avenue North

Unit #19

Suite 105

Phone: (404) 608-0006

Phone: (612) 561-9080

Phone: (216) 447-9030

Phone: (602) 437-1200

Fax: (404) 608-1123

Fax: (612) 561-0653

Fax: (216) 447-3097

Fax: (602) 437-2200

ILLINOIS

MISSOURI

PENNSYLVANIA

CALIFORNIA

Addison 60101 (Chicago)

311 Laura Drive

North Kansas City 64116

Willow Grove 19090

Ontario 91761 (Los Angeles)

Phone: (630) 628-6100

1141 Swift Avenue

520 North York Road

3949A East Guasti Road

Phone: (215) 658-1430

Fax: (630) 628-0023

P.O. Box 12393

Phone: (909) 390-5555

Fax: (215) 658-1433

Woodridge 60517 (Chicago)

Phone: (816) 221-2070

Fax: (909) 390-5554

TENNESSEE

2033 West 75th Street

Fax: (816) 221-2897

 

San Leandro 94577 (Oakland)

Phone: (630) 910-9200

St. Louis 63119

Nashville 37214

3039 Teagarden Street

Fax: (630) 910-0360

2262 Lebanon Pike

 

7574 Watson Road

Phone: (615) 882-0320

Phone: (510) 357-9762

MARYLAND

Phone: (314) 968-8950

Fax: (615) 882-0051

Fax: (510) 357-7939

Elkridge 21075 (Baltimore)

Fax: (314) 968-2790

TEXAS

 

7397-102Washington Blvd.

COLORADO

 

Phone: (410) 799-9394

NEW YORK

Dallas 75220

Denver 80216

Fax: (410) 799-9398

10720 N. Stemmons Freeway

Flushing 11365-1595(N.Y.C.)

5855 Stapleton Drive North

MASSACHUSETTS

Phone: (214) 353-2996

175-25Horace Harding Expwy.

Suite A-140

Fax: (214) 350-3943

Braintree 02185 (Boston)

Phone: (718) 225-2040

Phone: (303) 370-6909

 

719 Granite Street

Fax: (718) 423-9619

Houston 77055

Fax: (303) 370-6969

Phone: (781) 848-9810

 

West 10 Business Center

 

 

FLORIDA

Fax: (781) 848-6759

NORTH CAROLINA

1008 Wirt Road, Suite 120

Davie 33314 (Miami)

Franklin 02038 (Boston)

Charlotte 28209

Phone: (713) 682-0334

4343 South State Rd. 7 (441)

Franklin Industrial Park

4303-BSouth Boulevard

Fax: (713) 682-4867

Unit #107

101E Constitution Blvd.

Phone: (704) 525-4410

WASHINGTON

Phone: (954) 321-6635

Phone: (508) 520-8802

Fax: (704) 525-0618

Renton 98055 (Seattle)

Fax: (954) 321-6638

Fax: (508) 528-8089

OHIO

268 Southwest 43rd Street

 

MICHIGAN

Phone: (425) 251-6680

Tampa 33609

Columbus 43214

Troy 48083 (Detroit)

Fax: (425) 251-9337

4538 W. Kennedy Boulevard

4560 Indianola Avenue

1355 Combermere

 

Phone: (813) 877-9585

Phone: (614) 263-0929

 

Phone: (248) 597-5000

 

Fax: (813) 289-7948

Fax: (614) 263-1238

 

Fax: (248) 597-5004

 

Authorized Service Stations are located in many large cities. Telephone 800-487-8665 or901-541-6042 for assistance locating one. Parts and accessories forPorter-Cableproducts should be obtained by contacting anyPorter-CableDistributor, Authorized Service Center, orPorter-CableFactory Service Center. If you do not have access to any of these, call888-848-5175 and you will be directed to the nearestPorter-CableFactory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas grandes ciudades. Llame al800-487-8665 ó al901-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios para los productos PorterCable deben obtenerse poniéndose en contacto con cualquier distribuidorPorter-Cable,Centro de Servicio Autorizado o Centro de Servicio de FábricaPorter-Cable.Si no tiene acceso a ninguna de estas opciones, llame al888-848-5175 y le dirigirán al Centro de Servicio de FábricaPorter-Cablemás cercano. Des centres de service agréés sont situés dans beaucoup de grandes villes. Appelez au800-487- 8665 ou au901-541-6042 pour obtenir de l’aide pour en repérer un. Pour obtenir des pièces et accessoires pour les produitsPorter-Cable,s’adresser à tout distributeurPorter-Cable,centre de service agréé ou centre de service d’usinePorter-Cable.Si vous n’avez accès à aucun de ces centres, appeler le888-848-5175 et on vous dirigera vers le centre de service d’usinePorter-Cablele plus proche.

DELTA SERVICE CENTERS

ALBERTA

MANITOBA

QUÉBEC

Bay 6, 2520-23rdSt. N.E.

1699 Dublin Avenue

1515 ave.

Calgary, Alberta

Winnipeg, Manitoba

St-JeanBaptiste,

T2E 8L2

R3H 0H2

Québec, Québec

Phone: (403) 735-6166

Phone: (204) 633-9259

G2E 5E2

Fax: (403) 735-6144

Fax: (204) 632-1976

Phone: (418) 877-7112

BRITISH COLUMBIA

ONTARIO

Fax: (418) 877-7123

 

8520 Baxter Place

505 Southgate Drive

1447, Begin

Burnaby, B.C.

Guelph, Ontario

St-Laurent,(Montréal), Québec

V5A 4T8

N1H 6M7

H4R 1V8

Phone: (604) 420-0102

Phone: (519) 836-2840

Phone: (514) 336-8772

Fax: (604) 420-3522

Fax: (519) 767-4131

Fax: (514) 336-3505

The following are trademarks of PORTER-CABLECorporation (Las siguientes son marcas registradas dePORTER-CABLES.A.) (Les marques suivantes sont des marques de fabriquant de laPORTER-CABLECorporation): BAMMER®, LASERLOC®, OMNIJIG®, POCKET CUTTER®,PORTA-BAND®,PORTA-PLANE®,PORTER-CABLE®,QUICKSAND®, SANDTRAP®, SAW BOSS®,SPEED-BLOC®,SPEEDMATIC®, SPEEDTRONIC®,STAIR-EASE®,THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, TIGER CUB®, TIGER SAW®,TORQ-BUSTER®,VERSA-PLANE®,WHISPER SERIES®, DURATRONIC™, FRAME SAW™, INNOVATION THAT WORKS™, JETSTREAM™,MICRO-SET™,MORTEN™, NETWORK™, RIPTIDE™,TRU-MATCH™,WOODWORKER’S CHOICE™.

Trademarks noted with ® are registered in the United States Patent and Trademark Office and may also be registered in other countries. Las Marcas Registradas con el signo de ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden estar registradas en otros países. Marques déposées, indiquées par la lettre ®, sont déposées au Bureau des brevets d’invention et marques déposées aux Etats-Uniset pourraient être déposées aux autres pays.