Polk Audio 265-RT, 255C-LS, 255C-RT, 65F-X, 65-RT User Manual

...
0 (0)

LS Models 265-ls

65f/x®-ls

65-ls

255c-ls

RT Models 265-rt 625-rt

65f/x®-rt

65-rt

255c-rt

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS READ BEFORE OPERATING EQUIPMENT

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with dry cloth.

7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

10.WARNING: To reduce the risk of fire or electric shock, this apparatus should not be exposed to rain or moisture and objects filled with liquids, such as vases, should not be placed on this apparatus.

Product Disposal—Certain international, national and/or local laws and/

or regulations may apply regarding the disposal of this product. For further

detailed information, please contact the retailer where you purchased this product or the Polk Audio Importer/

Distributor in your country. A listing of Polk Audio Importer/Distributors can be found on the Polk Audio website www.polkaudio.com or by contacting

Polk Audio at 5601 Metro Drive, Baltimore, Maryland 21215, USA—Phone: +1 410 358-3600.

WARNING: Listen Carefully

Polk Audio loudspeakers and subwoofers are capable of playing at extremely high volume levels, which could cause serious or permanent hearing damage. Polk Audio, Inc. accepts no liability for hearing loss, bodily injury or property damage resulting from the misuse of its products.

Keep these guidelines in mind and always use your own good judgment when controlling volume:

You should limit prolonged exposure to volumes that exceed 85 decibels(dB).

For more about safe volume levels, go to the Occupational Health and Safety Administration (OSHA) guidelines at http://www.osha.gov/dts/ osta/otm/noise/standards_more.html

Take Inventory

Inside each speaker container, you should find the following:

1.One in-wall loudspeaker or one set of loudspeakers for F/X® models only.

2.Speaker cutout mounting template

3.One Sheer-Grille (for each speaker)

3.Port plug (265-ls, 65f/x-ls, 65-ls, 265-rt, 65f/x-rt & 65-rt only)

4.One Owner’s Manual

5.Registration Card

Important Note: If anything is missing or damaged, or if your speaker fails to operate, notify Polk Audio Customer Support Services immediately at 800-377-7655.

Installation Recommendation For Optimum Performance

Important Note: Vanishing Series Loudspeakers are not magnetically shielded and should not be placed closer than 1’ (30cm) from a CRT (tube) television or video monitor.

Important Note: You should have a thorough understanding of and adhere to all local building and fire codes. Also, you should be familiar with the area behind the wall or ceiling into which you plan to install your speakers. Always use wire that meets appropriate building and fire codes. (Note: Wiring is best performed

by an experienced professional.)

When installing your loudspeakers, be aware of the weight of your particular model and the sturdiness of the material into which you are installing the speaker. Be aware of any concealed studs, electrical wiring or plumbing in the wall or ceiling into which you are installing the speakers.

If you doubt that you possess the necessary skills or tools, consult your Polk Audio dealer or a professional installer.

Wire Recommendations

(minimum recommended)

Runs

Gauge

Lengths up to 25'

18 or 16

Lengths greater than 25'

16 or 14

but less than 50'

 

Lengths greater than 50'

14 or 12

but less than 75'

 

Lengths greater than 75'

12

Loudspeaker Installation

You will need:

Pencil for marking the location of installation.

Keyhole saw, utility knife or materialappropriate tool for cutting drywall or other wall material.

Level.

Screwdriver, preferably powered, with Phillips Head bit.

Power drill with appropriate bit

(optional, for starting wall cut).

Trace around the template.

Cut the hole with the appropriate tool.

Important information Before you Install your LoudSpeakers

Wall Or Ceiling Surface Preparation

If you’re installing your Vanishing Series speaker into a heavily textured wall or ceiling (e.g. stucco or popcorn finish), you must prepare the wall surface immediately around the speaker cutout. Sanding and smoothing the wall or ceiling surface will ensure the speaker and grille both seat properly and flat to the surface.

2

Polk Audio Customer Service: 1-800-377-7655 (Outside US & Canada: 410-358-3600) Monday-Friday, 9:00 AM-6:00 PM EST, polkcs@polkaudio.com

Important information Should YOu Choose to Paint your grilles

Because of its ultra-thin profile, the Vanishing Series Sheer-Grille requires a specific painting procedure to ensure smooth, even coverage. The grille scrim and perforated grille come assembled and require no disassembly.

Paint Recommendation

We highly recommend you use a can of spray paint matched to the wall color you want the Sheer-Grilles to blend with.

Important Note: Never use a brush or roller to paint the grilles, as this will clog the perf holes.

To paint the Sheer-Grille

1.Elevate the Sheer-Grille off of a flat surface. This will ensure even coverage of the grille frame and make it easier to pick up.

Mounting Idea: Two spray can caps will raise the grille high enough.

2.Hold the spray paint about 12" from the grille and at a 45° angle.

3.Apply one light, thin coat, moving evenly side to side over the grille, then work your way around the perimeter of the grille

to ensure you cover the grille frame.

4.After each application of paint, wait approximately 1 minute, rotate the grille 90°, and apply the next thin coat.

Important Note: You must rotate the grille

90°. Use your hands to define the next 90° rotation and always rotate the grille in the same direction of travel.

5.Three light, even applications should cover the grille and frame adequately. Remember to work your way around the grille frame to cover it evenly and completely.

Surround SPEAKER PLACEMENT

Polk Audio F/X® surround loudspeakers give you nearly endless placement options. But remember that where you place your surround speakers requires some careful thought, as installation requires that you cut a hole in your wall or ceiling.

tV

Diagram shows speaker locations for 5.1 and 7.1 systems, when two additional in-wall speakers are installed in the rear wall.

Left/Right Orientation: F/X® surround loudspeakers have a left/right orientation, and each speaker is clearly marked on the serial number label on the back of the magnet for installation on either the right or left. Right and left are defined from your listening area as you face your system’s center channel.

Center Channel Speaker Placement

Install the 255c-ls or 255c-rt as close as possible to ear level. If the speaker needs to be installed higher, aim the tweeter down as required.

Do not block the center channel with your TV or furniture.

Please Note: For more on speaker placement go to: www.polkaudio.com/education/article.php?id=15 or www.polkaudio.com/downloads/hthandbook.pdf

Room Environment Controls

Imaging

Diffuse / Solid

Imaging (65f/x-ls model only)

F/X Surround Loudspeakers offer switchable “Diffuse” and “Solid” imaging patterns

to create the surround effect you desire.

A “Diffuse” image is defined as one which creates a “cloud” of sound; think of the effect as ambient sounds which fill the environment all around you, but are less localizable.

A “Solid” image is one which creates a more pinpoint sound; sound is more localized. The location of sounds in the sound field is more identifiable.

Tweeter

Filter / Norm

Tweeter Switch

(LS and RT models except F/X models) Filter—If your listening room is very reflective, with smooth sheetrock walls, hardwood floors, and non-cushioned furniture, the sound will be

overly “bright” and unnatural. Selecting the “Filter” setting compensates for the effect of reflectiv-

ity in a hard room. Tweeter attenuation flattens room response, without hindering higher frequency response, for warmer, more realistic sound

and more accurate imaging.

Norm—If your room is not reflective, with curtains, artwork, lots of cushioned furniture and carpeting, sound will be absorbed by the room, resulting in more realistic reproduction and more accurate imaging. In this case, select the tweeter “Norm” setting.

Wall Dist.

<2' >2'

(60cm) (60cm)

Wall Distance Switch (65f/x-rt and all LS Models except the Center Channel)

In-wall loudspeakers excel when placed more than 2’ (60cm) from side walls. If position limitations demand that in-wall loudspeakers

be installed closer than 2’ (60cm) from side walls or ceiling, the proximity of the surface can result in a response “bump” between 50 and 200Hz.

This can cause in-wall speakers to sound “boomy.” The “Wall Distance” switch flattens response

and eliminates “boominess” without sacrificing deep bass response, for more lifelike sound.

For more information visit our website at www.polkaudio.com

3

When to Use the Provided Port PluG Important Note: Use the provided port plug when you are installing any of the in-wall loudspeakers listed below in an area larger than a standard open stud bay. Ensure the plug seats all

the way into the port.

The port plug should be used on the following models: 265-ls, 65f/x-ls, 65-ls, 265-rt, 65f/x-rt & 65-rt.

Dimensions

 

 

 

 

 

 

Model

265-ls

265-rt

65f/x-ls

65f/x-rt

 

 

 

 

 

A. Overall Dimensions

20 7/8" H x 8 7/8" W

20 7/8" H x 8 7/8" W

14 3/8" H x 8 7/8" W

14 3/8" H x 8 7/8" W

 

(530.2mm x 225.4mm)

(530.2mm x 225.4mm)

(365.1mm x 225.4mm)

(365.1mm x 225.4mm)

 

 

 

 

 

B. Cutout Dimensions

19 3/16" H x 7 1/4" W

19 3/16" H x 7 1/4" W

12 3/4" H x 7 1/4" W

12 3/4" H x 7 1/4" W

 

(487.4mm x 184.2mm)

(487.4mm x 184.2mm)

(323.9mm x 184.2mm)

(323.9mm x 184.2mm)

 

 

 

 

 

 

 

C. Product Depth

3

3/4" (95.3mm)

3

3/4" (95.3mm)

3 1/2" (88.9mm)

3 1/2" (88.9mm)

 

 

 

 

 

 

 

D. Mounting Depth

3

1/4" (82.6mm)

3

1/4" (82.6mm)

3" (76.2mm)

3" (76.2mm)

(using 1/2" drywall)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Dimensions

 

 

 

 

 

 

Model

625-rt

65-ls

65-rt

 

 

 

 

 

 

A. Overall Dimensions

14 3/8" H x 8 7/8" W

14 3/8" H x 8 7/8" W

14 3/8" H x 8 7/8" W

 

 

(365.1mm x 225.4mm)

(365.1mm x 225.4mm)

(365.1mm x 225.4mm)

 

 

 

 

 

 

B. Cutout Dimensions

12 3/4" H x 7 1/4" W

12 3/4" H x 7 1/4" W

12 3/4" H x 7 1/4" W

 

 

(323.9mm x 184.2mm)

(323.9mm x 184.2mm)

(323.9mm x 184.2mm)

 

 

 

 

 

 

 

 

C. Product Depth

3

3/8" (85.7mm)

3

1/2" (88.9mm)

3 1/2" (88.9mm)

 

 

 

 

 

 

 

D. Mounting Depth

2

7/8" (73mm)

3" (76.2mm)

3" (76.2mm)

 

(using 1/2" drywall)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Dimensions (Center Channel)

 

 

 

 

Model

255c-ls

255c-rt

 

 

 

 

 

 

 

 

 

A. Overall Dimensions

9

5/16" H x 14 13/16" W

9

5/16" H x 14 13/16" W

 

 

 

(236.5mm x 376.2mm)

(236.5mm x 376.2mm)

 

 

 

 

 

 

 

 

 

B. Cutout Dimensions

7

5/8" H x 13 1/8" W

7

5/8" H x 13 1/8" W

 

 

 

(193.7mm x 333.4mm)

(193.7mm x 333.4mm)

 

 

 

 

 

 

 

 

 

C. Product Depth

3

3/4" (95.3mm)

3

3/4" (95.3mm)

 

 

 

 

 

 

 

 

 

D. Mounting Depth

3

1/4" (82.6mm)

3

1/4" (82.6mm)

 

 

(using 1/2" drywall)

 

 

 

 

 

 

 

 

 

 

 

 

 

Specifiations

 

 

 

 

 

 

For complete Vanishing Series specifications, visit www.polkaudio.com

4

Polk Audio Customer Service: 1-800-377-7655 (Outside US & Canada: 410-358-3600) Monday-Friday, 9:00 AM-6:00 PM EST, polkcs@polkaudio.com

Polk Audio 265-RT, 255C-LS, 255C-RT, 65F-X, 65-RT User Manual

A B C D

A B

A B

A B

C

D

For more information visit our website at www.polkaudio.com

5

Loading...
+ 11 hidden pages