Calisto® 620
Bluetooth Wireless
Speakerphone + Bluetooth
USB Adapter
Designed in Santa Cruz, California
QUICK START GUIDE
|
3 |
|
4 |
2 |
|
|
1 |
|
1 |
Call button |
|
|
Answer or end a PC or Mobile call |
1 short key press |
|
Answer a 2nd call while on a call |
1 short key press ends |
|
1st call, 2nd short key press answers 2nd call |
|
2 |
Mute microphone button |
|
|
Mute mic 1 short key press mutes; Mute LED turns solid |
|
|
red |
|
|
Unmute mic 1 short key press unmutes; Mute LED turns |
|
|
off |
|
3Pairing
Flashing red/blue In pairing mode
Solid blue Paired successfully; times out after 10 minutes
4Volume up, Volume down
Increase/decrease volume Press up/down volume buttons
Ringer volume Press volume up/down keys while no call is active
88530--02 (07-12)
1 |
Speakerphone |
2 |
PC |
Charge |
Connect and Call |
Charge of a minimum of 30 minutes needed for complete setup.
The speakerphone can be charged with a wall charger or with a USB cord and your PC. The power LED on the speakerphone will be solid red when charging and off when fully charged.
A full charge with a wall charger will take approximately 1 ½ hours.
A full charge with a USB cord and your PC will take approximately 2 ½ hours.
NOTE To charge the speakerphone with the USB cable and PC, the PC must be on and in an active state (not standby). See the complete user guide at http://docs.plantronics.com/calisto-620
Turn speakerphone off when not in use to save battery power.
1Insert the Bluetooth USB adapter into the PC.
NOTE For best results plug directly into PC and not a hub or docking station.
The speakerphone and USB adapter are pre-paired and will connect automatically when USB adapter is connected to the PC and the speakerphone is powered on and in range of the PC.
2Slide the power switch on the speakerphone to the “On” position.
The LED on the USB adapter will flash and then turn solid blue when the speakerphone is connected to the Bluetooth adapter.
3Load Plantronics Enterprise software by visiting plantronics.com/software and click on the download button.
4Check your audio settings, as necessary.
Confirm the speaker and microphone settings for your PC softphone are set to Plantronics BT300C.
Windows 7
Go to Control Panel -> Sound-> Playback tab, and set the
Plantronics BT300C device as both the Default
Communications Device and the Default Audio Device. In the Playback tab, this is indicated by the green checkmark.
Windows XP
Go to Control Panel -> Sounds and Audio Devices, and in the Audio tab set the Plantronics BT300C for both the Sound playback and Sound recording sections. In the Voice tab, select the Plantronics BT300C item for both the Voice playback and Voice recording sections.
5Make a test call from your computer softphone. During an active call, the Bluetooth USB adapter will flash blue.
6End the call by pressing the speakerphone call button.
3 Mobile Phone
Connect and Call
1Ensure your speakerphone is fully charged. Place the speakerphone in pairing mode by pressing and holding the power button to the RIGHT until the Bluetooth pairing LED flashes RED/BLUE.
NOTE If you don’t see the red and blue flash, slide the power button all the way LEFT to turn speakerphone off. Then press and hold the power button again until you see the red and blue flash.
The speakerphone will stay in pairing mode for ten minutes.
2Place Bluetooth mobile phone into search mode. Select Calisto 620 from the list of devices found.
Calisto 620
3If prompted by your mobile phone for a passcode enter 0000.
The LED will stop flashing when your speakerphone and phone are successfully paired.
4Make a test call from your mobile phone.
5End the call by pressing the speakerphone call button.
Bluetooth Connection
To Re-Pair USB adapter
In the event the USB adapter and speakerphone become unpaired.
1Start with the speakerphone powered off.
2Remove the Bluetooth USB adapter.
3Place the speakerphone in pairing mode by pressing and holding the power button to the RIGHT until the Bluetooth pairing LED flashes BLUE/RED.
4Insert the Bluetooth USB adapter into your PC USB port. The LED will flash and then turn solid blue to indicate the speakerphone is connected to the Bluetooth USB adapter.
5Speakerphone will exit pairing mode. See the complete user guide at http://docs.plantronics.com/calisto-620
The speakerphone wireless range is 10m/33feet
NEED MORE HELP?
Product support
http://www.plantronics.com/support
Online user guide
http://docs.plantronics.com/calisto-620
Please refer to the separate safety instructions for important product safety information prior to installation or use.
Declaration of Conformity
We Plantronics, 345 Encinal Street, Santa Cruz, California, 95060 USA (800) 544-4660, declare under our sole responsibility that the product BT300M Adapter complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Exposure to RF Radiation
The internal wireless radio operates within the guidelines found in radio frequency safety standards and recommendations, which reflect the consensus of the scientific community. Independent studies have shown that the internal wireless radio is safe for use by consumers. Visit plantronics.com for more information.
In order to comply with FCC and IC RF Exposure requirements, the base must be installed and operated such that a minimum separation distance of 20 cm is maintained between the base and all persons during normal operation.
NOTE: Modifications not expressly approved by Plantronics, Inc. could void the user’s authority to operate the equipment.
Industry Canada Regulatory Information
This product meets the applicable Industry Canada technical specifications/Le présent materiel est conforme aux specifications techniques applicable d’ Induristrie Canada.
This Class B digital apparatus complies with Canadian ICES-003. /Cet appareil numérique de la classe
Plantronics, Inc.
345 Encinal Street
Santa Cruz, CA 95060
United States
©2012 Plantronics, Inc. All rights reserved. Plantronics and Calisto are trademarks or registered trademarks of Plantronics, Inc. The Bluetooth trademark is owned by Bluetooth SIG, Inc. and any use of the mark by Plantronics, Inc. is under license. Microsoft, Lync, Windows, and Windows XP are registered trademarks of Microsoft Corporation in the US and other countries.
Calisto® 620
Bluetooth Wireless
Speakerphone + Bluetooth
USB Adapter
Designed in Santa Cruz, California
QUICK START GUIDE
GUIA DE INÍCIO RÁPIDO
3
4 2 1
1Botón de llamada
Contestar o finalizar una llamada de PC o teléfono celular 1 pulsación breve
Responda una 2da llamada mientras transcurre la llamada
1 pulsación breve finaliza la 1era llamada, la 2da pulsación breve contesta la 2da llamada
2Botón Silencio del micrófono
Silenciar micrófono 1 pulsación breve silencia, el LED de silenciar se vuelve rojo sin parpadeo
Quitar silencio al micrófono 1 pulsación breve quita el silencio, el LED de silenciar se apaga
3Emparejamiento
Parpadeo rojo/azul En modo emparejamiento
Azul sin parpadeo Emparejado exitoso, expira después de
10 minutos
4Subir y bajar el volumen
Aumentar/disminuir el volumen Presionar botones para subir/bajar el volumen
Volumen del timbre Presionar teclas para subir/bajar el volumen mientras no hay llamadas activas
88530-00
1 Teléfono con altavoz
Cargar
Se requiere una carga de un mínimo de 30 minutos para la configuración completa.
Se puede cargar el altavoz con un cargador de pared o un cable USB y su PC. El LED de encendido del altavoz tendrá una luz roja continua cuando se esté cargando y estará apagado cuando la carga esté completa.
2 PC
Conecte y llame
1Inserte el adaptador Bluetooth USB en la PC.
NOTA Para obtener mejores resultados, enchufe directamente en la PC y no en un concentrador o estaciones de conexión.
El altavoz y el adaptador USB están emparejados previamente y se conectarán de manera automática cuando el adaptador
USB esté conectado a la PC y el altavoz esté encendido y en rango de la PC.
3 celular con Bluetooth
Conecte y llame
1Asegúrese de que su altavoz esté completamente cargado.
Coloque el altavoz en modo de emparejamiento al mantener presionado el botón de encendido a la DERECHA hasta que el
LED de emparejamiento de Bluetooth parpadee en
ROJO/AZUL.
NOTA Si no ve el parpadeo rojo y azul, deslice el botón de encendido hasta el extremo IZQUIERDO, para apagar el altavoz.
Luego presione y mantenga presionado el botón de encendido nuevamente hasta que vea un parpadeo rojo y azul.
El altavoz permanecerá en modo de emparejamiento durante diez minutos.
Una carga completa con un cargador de pared tardará aproximadamente 1 ½ horas.
Una carga completa con un cable USB y su PC tardará aproximadamente 2 ½ horas.
NOTA Para cargar el altavoz con el cable USB y la PC, esta debe estar encendida y en estado activo (no en espera). Consulte la guía completa del usuario en http://docs.plantronics.com/calisto-620
Apague el altavoz cuando no esté en uso para ahorrar energía.
2Deslice el interruptor de encendido del altavoz a la posición
“Encendido”.
El LED del adaptador USB parpadeará y luego se volverá de un azul sin parpadear cuando el altavoz esté conectado al adaptador Bluetooth.
3Para cargar el software de Plantronics visite plantronics.com/software y haga clic en el botón de descarga.
4Revise su configuración de audio según sea necesario.
Confirme que los ajustes de la bocina y el micrófono para su teléfono de PC estén configurados en Plantronics BT300.
Windows 7
Vaya a Panel de control -> Sonido-> Reproducción y configure el dispositivo Plantronics BT300 como Dispositivo de comunicaciones predeterminado y Dispositivo de audio predeterminado. En la ficha Reproducción, esto se indica con una marca de verificación verde.
Windows XP
Vaya a Panel de control -> Sonidos y dispositivos de audio, y en la ficha Audio configure Plantronics BT300 para Reproducción de sonido y Grabación de sonido. En la ficha Voz, seleccione el elemento Plantronics BT300 para las secciones de Reproducción de voz y Grabación de voz.
5Haga una llamada de prueba desde su teléfono de PC.
Durante una llamada activa, el adaptador USB Bluetooth parpadeará en color azul.
6Finalice la llamada presionando el botón de llamada.
2Coloque el teléfono móvil Bluetooth en el modo búsqueda. Seleccione Calisto 620 de la lista de dispositivos encontrados.
Calisto 620
3Si su teléfono celular le solicita ingresar una contraseña, ingrese 0000. La luz LED dejará de parpadear cuando el altavoz y el teléfono se hayan emparejado correctamente.
4Haga una llamada de prueba desde su teléfono celular.
5Finalice la llamada presionando el botón de llamada.
Conexión Bluetooth
Volver a emparejar a través de adaptador USB
En caso de que el adaptador USB y el altavoz dejen de estar emparejados.
1Empiece con el altavoz apagado.
2Extraiga el adaptador USB Bluetooth.
3Coloque el altavoz en modo de emparejamiento al mantener presionado el botón de encendido a la DERECHA hasta que el
LED de emparejamiento de Bluetooth parpadee en
AZUL/ROJO.
4Inserte el adaptador USB Bluetooth directamente en el puerto USB de la PC. La luz LED parpadeará y luego se mantendrá de color azul sin parpadear para indicar que el auricular está conectado al adaptador USB Bluetooth.
5El altavoz saldrá del modo de emparejamiento. Consulte la guía completa del usuario en http://docs.plantronics.com/calisto-620
El alcance inalámbrico del altavoz es de 10 m / 33 pies
¿NECESITA MÁS AYUDA?
Asistencia para productos
http://www.plantronics.com/support
Guía del usuario en línea
http://docs.plantronics.com/calisto-620
Antes de instalar o utilizar el producto, consulte el folleto de instrucciones de seguridad (aparte) para obtener información importante acerca de la seguridad del producto.
Nota a los usuarios:Callisto 620 contiene un altavoz inalámbrico Bluetooth modelo P620S y un dispositivo Bluetooth USB modelo BT300.