Size:
647.84 Kb
Download

CORDLESSHEADSET

TELEPHONE

CT11/12

CT11

CT12

PRODUCT INFORMATION BOOKLET

WELCOME

This Product Information Booklet contains features and operations not described in the Quick Start Guide (QSG). The QSG also includes warranty information, FCC and the Industry Canada Notice.

BASICS . . . . . . . . . . . . . . . . . . . 3

Caller ID Options . . . . . . . . . . . 3 Making and Receiving Calls. . . . 6 Ringer Tone Setting. . . . . . . . . . 7 Ringer Volume Setup . . . . . . . . 8 Ringer Mute (temporarily) . . . . . 8 Redialing a Call . . . . . . . . . . . . 9 Distinctive Ringer Setup. . . . . . 10 Adjusting Headset Volume . . . 11 Mute Microphone . . . . . . . . . . 11 Tone Dialing Switch-over . . . . .12 TravelingOut-of-Range . . . . . .12 Selecting a Different Channel . 13 Find Remote. . . . . . . . . . . . . . 13 Flash and Call Waiting . . . . . . 14 Voice Mail LED . . . . . . . . . . . . 14

PHONEBOOK. . . . . . . . . . . . . 15

Steps to Enter Names

and Special Characters . . . . . . 16 Storing Names, Phone

Numbers, Distinctive Rings,

and Speed Dial. . . . . . . . . . . . 17 Phonebook Storage Process . . 18

Viewing the Phonebook. . . . . . 20 Making Phonebook Calls. . . . . 22 Speed Dialing. . . . . . . . . . . . . 23 Editing the Phonebook . . . . . . 23 Chain Dialing . . . . . . . . . . . . . 25 One Touch Dialing . . . . . . . . . 26

CALLER ID . . . . . . . . . . . . . . . 28

Viewing the Caller ID List . . . . 31 Deleting Information from

the Caller ID List . . . . . . . . . . . 32 Using Caller ID Message List . . 33 Call Waiting Deluxe Features . . 35

MORE. . . . . . . . . . . . . . . . . . . 36

Changing the Digital

Security Code . . . . . . . . . . . . . 36 Installing the Beltclip . . . . . . . . 38 Note on Power Sources. . . . . . 39 Maintenance . . . . . . . . . . . . . 40 General Information . . . . . . . . 41

TROUBLESHOOTING . . . . . . . 42 PARTS & ACCESSORIES . . . . . 44 INDEX . . . . . . . . . . . . . . . . . . 47

2

BASICS

There are three Caller ID setup options available: AUTOTALK, CIDCW (Caller ID on Call Waiting), andAREA CODE.

AUTOTALK allows you to answer the phone without

pressing TALK/FLASH. If the phone rings when AutoTalk is On, simply remove the remote from the base and the phone automatically answers the call. Or if the remote is not in the base, press any number key,/TONE, or # to answer the call. If you set AutoTalk to Off, you must press talk/flash to answer the call. Setting AutoTalk follows in this section.

CIDCW (Caller ID on Call Waiting) performs the same as regular Caller ID on a call waiting number.

CW Deluxe allows you to handle call waiting calls in seven different ways. See page 28 for the Caller ID (CID) section and page 35 for CW Deluxe.

You must subscribe to CID and CIDCW from your phone company in order to use this feature.

The CW Deluxe is a separate service available through your phone company.

ASICSB

TIP

Any key answer can be used only when AutoTalk is set to On.

3

TIP

Standby Mode:

The remote is not in use, is off the base, and

TALK/FLASH has not been pressed. A dial tone is not present.

4

AREA CODE allows you to enter your local area code so CID will not show the area code from local callers. See the next page for area code instructions.

To change your Caller ID options:

1) When the phone is in the standby mode, press

MENU/MUTE.

2) Press ▲ or ▼ to move the pointer to “Caller ID

Setup”, then press SELECT/CH.

3) Press ▲ or ▼ to choose “Auto Talk” or “CIDCW”,

then press SELECT/CH.

4) Press ▲ or ▼ to change the selection.

AutoTalk: “Auto Talk

On” or “Auto Talk

Off”

CIDCW: “CIDCW

On”, “CW Deluxe

On” or “CIDCW Off”

5)Press SELECT/CH, and you will hear a confirmation tone.

6)Press END to exit.

ENTERINGYOURAREACODE

If you enter a 3-digitarea code number in the “Area Code” option, your local area code does not appear in Caller ID messages. For calls received from outside your local area code, you will see a full10-digitnumber.

1) When the phone is in the standby mode, press

MENU/MUTE.

2) Press ▲ or ▼ to move the pointer to “Caller ID Setup”, then press SELECT/CH.

3) Press ▲ or ▼ to move the pointer to “Area Code”, then press

SELECT/CH.

4) Use the number keypad (0 to 9) to enter a 3-digitarea code.

5)Press SELECT/CH, and you will hear a confirmation tone.

6)Press END to exit.

TIP

B

 

ASICS

If your calling area requires 10-digitdialing, do not program this option.

TIP

If the area code has already been stored in memory, the stored area code will be displayed in this mode. To change it, press delete and the number keypad to enter the new area code.

5

MAKING ANDRECEIVINGCALLS

To make or receive a call, you need to connect the Firefly™ headset to the remote unit. (See the Quick Start Guide.)

Put on the headset.

 

Remote On Base

Remote Off Base

To answer

Pick up the remote

Press TALK/FLASH

 

and press TALK/FLASH

OR

 

 

OR

(AutoTalk) Press any

 

(AutoTalk) Pick up

number key, /TONE,

 

the remote.

or # .

To make

1)

Pick up the remote.

Dial the number, then

a call

2)

Dial the number, then

press TALK/FLASH.

NOTE: The

 

press TALK/FLASH.

 

remote must be

 

OR

OR

out of the base

 

during calls.

1)

Pick up the remote.

1) Press TALK/FLASH.

Replacing the

2)

Press TALK/FLASH.

2) Listen for the dial tone.

remote will

3)

Listen for the dial tone.

3) Dial the number.

cause the call

4)

Dial the number.

 

to disconnect.

 

To hang up

Press END, or return the remote to the base.

To enter

When you dial the number, press

a pause

PAUSE/REDIAL. “P” appears in the

within

display which represents a pause.

the dialing

 

 

 

sequence

 

 

 

The headset LED will continue flashing during Talk Mode.

When you press DELETE during a call, the call will be placed on hold and you will hear a ring tone. To resume the call, pressTALK/FLASH orDELETE. If the remote remains idle for 5 minutes, the phone hangs up and returns to the Standby automatically.

6

RINGERTONESETTING

1) When the phone

is in the standby mode, press

MENU/MUTE.

2) Press orto

move the pointer to “Ringer Tones”.

You can choose from 6 ringers or

4 melodies:

Ringers [Flicker,

Clatter, Leap Frog, Ping Ball, Reminder, Soft Alert]

Melodies [Beethoven 9, For Elise (Elise), Merry Christmas (Merry-Xmas),Home Sweet Home (Hm Swt Hm)]

3)You will hear the ringer or the melody as you scroll through the options.

4)Press SELECT/CH and you will hear a confirmation tone.

5)Press END to exit.

ASICSB

TIPS

Standby mode is when the remote is charged and the Talk button has not been pressed. The display is blank.

If you set the ringer to Off, the ringer tone will not sound.

7

RINGERVOLUMESETUP

TIP

If you select “Ringer Off”, <Ringer Off> appears on the display when you make or receive calls, or when charging the remote.

1)When the phone is in the standby mode, press MENU/MUTE.

2) Press ortomove the pointerto “Ringer Volume”,then pressSELECT/CH.

3)Press orto move the pointer through the ringer settings (Ringer Off, Ringer Low, or

Ringer High). You will hear a ringer or melody

at the selected volume (or does not ring when you select “Ringer Off”).

4)Press SELECT/CH, and you will hear a confirmation tone.

5)Press END to exit.

RINGER MUTE (TEMPORARILY)

You can temporarily mute the ringer tone. When the remote is off the base and the phone is ringing, press END. The ringer tone will return to the previous setting starting with the next incoming call.

8

REDIALING ACALL

The last three phone numbers dialed can be quickly redialed.

REDIALING FROMSTANDBYMODE

1)Press PAUSE/ REDIAL.The

phone number

 

that was last

 

dialed appears

PAUSE/REDIAL

on the display.

 

2) Press PAUSE/

 

REDIAL again.

PAUSE/REDIAL

Each press of

 

PAUSE/REDIAL

 

will display one

 

of the last three PAUSE/REDIAL

numbers

 

dialed.

 

3)Press TALK/FLASH. The selected number is dialed.

4)Press END to hang up.

REDIALING FROMTALKMODE

1)Press TALK/FLASH.

2)Press PAUSE/REDIAL. The last number dialed will be displayed and redialed.

3)Press END to hang up.

TIPS

B

 

ASICS

If the number exceeds 32 digits, only the first 32 digits are retained in redial memory.

If the redial memory is empty, you will hear a beep.

If you have not pressed any key for 30 seconds, the phone returns to standby mode.

If you press END, the operation is canceled and the phone will return to the standby mode.

When using the redial feature in talk mode, only the last number dialed will be displayed.

9

DISTINCTIVERINGERSETUP

TIP

See ”Storing Phone Numbers, Names, Distinctive Rings, and Speed Dial” on page 17 for storing a Distinctive Ring in the Phonebook.

“Distinctive Ringer” allows you to preset memory locations with a designated ring tone. When an incoming call is received and the Caller ID information matches the information in one of the memory locations, the Distinctive Ring that has been stored for that particular caller will sound.

If you have set multiple memory locations with distinctive rings, switching the setting to “Distinctive Off” will result in no distinctive ringing. All incoming calls will have a normal ring tone. Switching to “Distinctive On” will activate all programmed distinctive ring memory locations.

1) When the phone is

in the standby mode, press

MENU/MUTE.

2) Press orto move the pointer to

“Distinct. Ring”, then press

SELECT/CH.

3)Press orto choose “Distinctive On” or “Distinctive Off”.

4)Press SELECT/CH, and you will hear a confirmation tone.

5)Press END to exit.

10

ADJUSTING THEHEADSETVOLUME

The remote headset volume settings (Volume Low, Volume Medium, Volume High, and Volume Maximum) can only be adjusted during a call. Press orto select the volume setting. When you hang up, the phone keeps the last volume setting selected.

TIP

When you press in maximum volume level orin lowest volume level, an error tone sounds.

ASICSB

MUTEMICROPHONE

You can temporarily

turn Off the micro-

phone so that the person you are talking with cannot hear you.

1) During a telephone call press and hold

MENU/MUTE for a few seconds to turn

Off the microphone, and “Mute” appears on the display.

2) Press MENU/MUTE again to cancel muting.

TIP

Do not press END to cancel muting.END will disconnect the call and the phone will return to standby mode.

11

TONEDIALINGSWITCH-OVER

TIP

The tone feature only applies when the dial mode is set to pulse.

A tone number can be stored in a memory location. This is referred to as Chain Dialing. (See page 25.)

Some telephone

companies use equipment that require pulse dialing (sometimes referred

to as rotary dialing). If you need to enter

tone dialing digits,

you can switch-overto tone dialing during the call. For example, entering your bank account number after you have called your bank.

Initially make your call with the pulse dialing mode. Once your call connects, press /TONE. Enter the desired number. These digits will be sent as tone dialing. Once the call ends, the tone mode is canceled and pulse dialing mode resumes.

TRAVELINGOUT-OF-RANGE

During a call, as you begin to move your remote too far from your base unit, static increases. If you pass the range limits of the base unit, your call will terminate within 30 seconds.

12

SELECTING ADIFFERENTCHANNEL

If you encounter interference while using your phone, you can manually change the phone’s channel for clear operation. This function works only when the phone is in use.

Press SELECT/CH. “Scanning” appears on the display, indicating the phone is changing to another channel.

FINDREMOTE

To locate the remote, press PAGE on the base. The remote beeps for 60 seconds, and “Paging”

appears on the display.

Paging is canceled when pressing any key on the remote or PAGE on the base. Additionally, if you receive an incoming call,PAGE is canceled.

TIP

If the remote battery is completely drained, the remote will not beep when paging.

13

ASICSB

FLASH ANDCALLWAITING

TIP

You must subscribe through your local telephone company to receive Call

Waiting Service.

If you have Call

Waiting service and

a call waiting tone sounds while you are on a call, press

TALK/FLASH to accept the waiting call. There is a short

pause, then you will

hear the new caller. To return to the original caller, press TALK/FLASH again.

MESSAGELED

The message waiting LED on the

remote is designed to work with your

voice mail service provided by your

local telephone company. The LED flashes when you have new incoming messages in the voice mail service.

You may need to occasionally reset the indicator if it remains On after you’ve retrieved your messages. To reset the indicator, when the phone is in the standby mode press and hold PAGE on the base until the paging sound stops (about 5 seconds).

14

USING THEPHONEBOOK

Phonebook allows you to dial a number using just a few key presses. It stores names/numbers in the Phonebook memory location, and you can search names in alphabetical order. You have a total of 100 locations that can be used for the Phonebook (including the Speed dials) and Caller ID messages.

If any of the following occurs while using the Phonebook function, operation will be canceled.

Press END. The phone will return to the standby mode (or the call will be disconnected).

Press TALK/FLASH.

Place the remote in the base.

Press DELETE, or receive an incoming call orPAGE (from the standby mode only).

Receive a CIDCW (Caller ID on Call Waiting) (during a call only).

HONEBOOKP

TIP

If the remote remains idle for 30 seconds, the phone will return to the standby mode (or back to the call).

15

STEPS TOENTERNAMES ANDSPECIAL

CHARACTERSUSING THEKEYPAD

Refer to the letters on the number keys to select the desired characters. With each press of a number key (0– 9), the displayed character appears in the following order: Upper case letters first, lower case letters next and finally the number corresponding to the key.

IF YOU MAKE A MISTAKE WHILE ENTERING A NAME

Use /tSPEED orCIDs to move the cursor to the incorrect character. PressDELETE to erase the wrong character, then enter the correct character. To delete all characters, press and holdDELETE.

16

USING THEPHONEBOOK

When entering names and/or phone numbers, each of the four steps in the entry process must be completed. A “Done” message and a beep indicate the name/phone number is complete.

When the phone is in the standby mode (Talk button not pressed), press /tSPEED.

The remote displays the number of the Phonebook locations used, and information on searching and storing Phonebook locations.

(1ST LINE) The number of the Phonebook entries

(2ND LINE) Press the number keypad, ▲ or ▼ to search

(3RD LINE) Press SELECT/CH button to begin the storage process.

17

HONEBOOKP

PHONEBOOKSTORAGEPROCESS

TIP

All four steps must be entered to complete the storage process. The display will read DONE and you will hear a beep.

TIPS

When the memory is full, you will hear a beep and “Memory Full” appears. You cannot store any more names and numbers.

STEP1: STORINGNAMES

1)From Standby (the Remote charged and the Talk Button not pressed— display is blank), press the /tSPEED button.

2)Press the SELECT/CH button to begin the

storage process. “Store/Edit Name” appears.

3)Enter the name (up to 16 characters) by using the number keypad.

See the “Steps for entering names and special characters” (see the previous table).

Use s andt to move the cursor to the desired location.

Use DELETE to delete characters as needed.

Press and hold DELETE to delete all the characters.

If a name is not required, skip step 3 and go to step 5.

4)Press SELECT/CH to store the name, then “Store/Edit No.” appears ready for the next step.

18

STEP2: STORINGPHONENUMBERS

5) From the “Store/Edit No.”

display. press the

number keypad to enter the phone number (up to 20 digits).

6) Press SELECT/CH to store the number.

STEP3: DISTINCTIVERINGS

7) “Distinctive Ring” appears. Then press ▲ or ▼ to

move the pointer to hear and choose one of the distinctive ring options.

8) Press SELECT/CH to store the distinctive ring.

STEP4: SPEEDDIAL

9) “Speed Dial” appears. Then press ▲ or ▼ to

move the pointer to select the speed dial location (10 locations: SPD1–SPD0).

10)Press SELECT/CH to store.

You will hear a confirmation tone and “Done!” appears on the display.

This completes your entry into the Phonebook. Now in the standby mode when you press the /tSPEED button, the Phonebook will show another entry.

TIPS

The pause key

 

counts as one

 

digit. Pressing

P

PAUSE/REDIAL

HONEBOOK

not to store a

more than once increases the length of pause between numbers.

If you choose

“Distinctive Ring”, simply select the “No Selectn” option.

If you select a speed dial

location where a number is already stored, the new number will replace the old number, and the old number will remain in the Phonebook, but no longer be on speed dial.

19

VIEWING THEPHONEBOOK

TIP

“/SD” appears on the display when you review the One Touch Dial, and “/SPDn” appears when you review a Speed dial.

Your phone stores names/numbers in the Phonebook memory locations, and you can search names in alphabetical order. You can view the Phonebook during a call as well as when the phone is in the standby mode.

1)Press /tSPEED. If you press

/tSPEED during

a call, the screen on

the right appears.

2) Press ▲ or ▼, or the

number keypad to view the Phonebook

locations.

A) ALPHABETICALORDER

Ascending order: Press ▼ to view locations. The location in the One Touch Dial appears first in the display. Each time ▼ is pressed, Phonebook locations appear in ascending order.

Descending order: Press ▲ to view locations. A name starting with a number or a mark, or <No Name> appears first. Each time ▲ is pressed, Phonebook locations appear in descending order.

20

B) FROM ANUMBERKEY

Refer to the letters on the number keys to select the first letter of the desired name. Press a number key until any name with the same initial is displayed (See the table in “Steps for Entering Names and Special Characters” on page 16).

For example, to search for “John” press 5 once. Press ▼ or ▲ until the name is displayed. If you press ▲ while the first name in “J” is displayed, a name starting with “I” will appear, or if you press ▼ while the last name in “J” is displayed, a name starting with “K” will appear.

3) To end viewing your Phonebook, press /tSPEED (if you view the Phonebook

during a call) or END.

HONEBOOKP

21

MAKINGCALLSUSING THEPHONEBOOK

FROMSTANDBYMODE

1) When the phone is in the standby mode, press

/tSPEED.

2)Press ▲ or ▼ to view the Phonebook locations (see “Viewing the Phonebook” on page 19).

3)Press TALK/FLASH. The displayed number is dialed.

4)To hang up, press END.

FROMTALKMODE

1) Press TALK/FLASH.

2)Press /tSPEED.

3)Press ▲ or ▼ to view the Phonebook locations (see “Viewing the Phonebook” on page 19).

4)Press SELECT/CH. The number in the displayed Phonebook location is dialed.

5)To hang up, press END.

22

SPEEDDIALING

If you have selected a speed dial memory location (10 locations: SPD1– SPD0) when storing a phone number in the Phonebook dial location, you can use the speed dialing feature.

1)When the phone is in the standby mode, press and hold a number key (0 – 9) associated with the speed dial.

The number stored in the speed dial appears.

2)Press TALK/FLASH. The phone number in the speed dial(SPD1–SPD0)is dialed.

3)Press END to end the call.

EDITING THEPHONEBOOK

1) When the phone is in the standby mode, press

/tSPEED.

2)Press ▲ or ▼, or the number keypad to view the Phonebook locations (see “Viewing the Phonebook” on page 19).

23

HONEBOOKP

3)When the Phonebook location to be editedappears, press

SELECT/CH. “Store/Edit Name” appears.

4)Follow the steps 3 to 7 under “Storing Phone Numbers, Names, Distinctive Rings and Speed Dial” starting on page 17 to complete the editing operation.

5)Press SELECT/CH. You will hear a confirmation tone and “Done!” appears on the display.

DELETING THESTOREDDATA

1) Select the Phonebook location to be deleted.

Press DELETE.

“Delete Memory?” appears.

2) Press ▲ to move the pointer to “Yes”.

3) Press SELECT/CHor delete. You hear a confirmation tone. “Deleted!”

appears in the display.

24

CHAINDIALING

The memory locations in the remote are not limited to phone numbers. You can also store a group of numbers (up to 20 digits), that you need to enter once your call connects. This is referred to as Chain Dialing.

An example of this is a bank account number. Store the special number in the Phonebook location (refer to “Storing Phone Numbers, Names, Distinctive Rings and Speed Dial” on page 17).

Once you have called your bank, and when you are prompted to enter the account number, press /tSPEED and use ▲ or ▼ to select the number in the Phonebook location, then pressSELECT/CH.

HONEBOOKP

25

ONETOUCHDIALING FORONENUMBER

You can store one number that you dial often in the One Touch Dial. The one touch dialing allows you to dial that number with one key press.

STORING THEONETOUCHDIAL

1) When the phone is in the standby mode, press

/tSPEED.

2) Press ▼ once to display the One Touch Dial menu.

3)Press SELECT/CH.

4)Store the name, phone number, and distinctive ring by following the steps 3 to 6 under “Storing Phone Numbers, Names, Distinctive Rings and Speed Dial” on page 17.

3)Press SELECT/CH. You will hear a confirmation tone and “Done!” appears on the display.

26

MAKINGCALLS WITH

THE ONETOUCHDIAL

When the phone is in the standby mode, press and hold /tSPEED. The number in the one touch location is dialed.

DELETING THEONETOUCHDIAL

1) When the phone is in the standby mode, press

/tSPEED.

2) Press ▼ once to display the One Touch Dial menu.

3) Press DELETE.

4) Press ▲ to move the pointer to “Yes”.

5)Press SELECT/CHor DELETE. You

hear a confirmation tone. “Deleted!” appears in the display.

HONEBOOKP

27

CALLERID

TIPS

If you answer a call before the Caller ID message is received (Example: before the second ring), the Caller ID message will not appear.

When a call is received via a telephone company that does not offer Caller ID service, the caller´s phone number and name do not appear. (This includes some international calls.)

When the call is via a private

branch exchange (PBX), the caller´s phone number and name may not appear.

28

YOU MUST SUBSCRIBE TOCALLERID SERVICE TO USE THIS FEATURE.

When the telephone rings, the Caller ID feature allows you to view the caller’s name and phone number on the display before you answer the phone. Additionally, you can dial the displayed number and store the information for memory dialing.

Make sure you have turned on the Caller ID/Call Waiting feature. (See page 4.)

Important:

The total memory locations for Caller ID messages and Phonebook locations (including Speed Dials) is 100 in total. When the memory locations (Phonebook and Caller ID) is 100, new Caller ID messages will overwrite the oldest Caller ID messages.

If any of the following occurs during Caller ID, operation will be canceled.

Press END. The phone will return to the standby mode (or the call will be disconnected).

Press TALK/FLASHor DELETE.

Place remote in base.

Receiving an incoming call or page (from the standby mode only).

Receive a CIDCW (Caller ID on Call Waiting) (during a call only).

The idle time is 30 seconds. If the remote remains idle for 30 seconds, the phone will return to the standby mode (or back to the call).

1)When the Caller ID message is received, the display shows the caller’s phone number along with the date and time. The incoming call information is stored in the Caller ID record. If the Caller ID service includes the caller’s name, the name will appear on the display. (up to 15 characters.)

TIP

The headset LED will continue flashing during Talk Mode.

ID ALLERC

29

TIP

When you press DELETE during a call, the call will be placed on hold and you will hear a ring tone. To resume the call, pressTALK/FLASH orDELETE. If the remote remains idle for 5 minutes, the phone hangs up and returns to the Standby automatically. To end a call, press theEND button.

30

CALLERID DISPLAYS

You may receive any one of the following messages:

When invalid data is received: “Incomplete Data”

When a private name is received: “Private Name”

When a private number is received: “Private Number”

When a unknown name is received: “Unknown Name”

When a unknown number is received: “Unknown Number”

2)When you pick up the phone, the display changes to “Talk”.

(AutoTalk feature is set to On.)

VIEWING THECALLERID LIST

The Caller ID list stores information for incoming calls — even unanswered calls. You can store 100 of the Caller ID messages and Phonebook locations (including Speed Dials) in total. You can view the Caller ID list during a call or when the phone is in the standby mode.

1) Press CIDs. The summary screen appears. The screen

shows the number of new messages and the total number of messages.

2)View Caller ID messages by following the procedure below.

FROM NEW TO OLD:

a.Press ▼ to display the latest Caller ID message.

b. Press ▼ to see the previous message.

FROM OLD TO NEW:

a.Press ▲ to display the earliest Caller ID message.

b.Press ▲ to see the next message.

IN ALPHABETIC ORDER:

Press the number keypad (2– 9 and0) to display the Caller ID messages in alphabetical order. Refer to the letters on the number keys to select the desired letter.

3)Press CIDs (if you view the Caller ID list during a call) or end.

TIP

The number of calls from the same Caller ID appears next to the received time. Once you have reviewed the new message, the number will be cleared and disappears.

TIP

Once you view the Caller ID list in alphabetical order, you cannot switch to the Caller ID display in historical order (from new to old or from old to new) unless you exit the operation.

31

ID ALLERC

TIP

Once the Caller ID data has been deleted, the information cannot be retrieved.

32

DELETINGINFORMATION

FROM THE CALLERID LIST

DELETING ACALLERID MESSAGE

1)While the incoming Caller ID information is displayed, press DELETE. “Delete Message?” appears.

2)Press ▲ or ▼ to choose “Yes” or “No”.

3) Press SELECT/CH

or DELETE.

WHEN THE POINTER IS AT “Yes”: A tone sounds and the Caller ID message is deleted. The next or previous Caller ID message is then displayed.

WHEN THE POINTER IS AT “No”: The display returns to the Caller ID message.

Deleting All Caller ID Names/Numbers

1) Press CIDs.

2) Press DELETE.

3) Press ▲ or ▼ to choose “Yes” or “No”.

4)Press SELECT/CHor DELETE.

WHEN THE POINTER IS AT “Yes”: A tone sounds and all stored Caller ID messages are deleted.

WHEN THE POINTER IS AT “No”: The display returns to the summary screen.

USING THECALLERID MESSAGELIST

CALLING APARTY FROM THECALLERID LIST

FROM STANDBY MODE

1) Press CIDs. The summary screen appears. The

screen shows the number of new messages and the total number of messages.

2)Use the number keypad (2 – 9 and0), ▲, or ▼ to view the Caller ID message list.

3) Press TALK/FLASH.

Talk

The displayed phone

8005551234

 

number dials

 

automatically.

 

FROM TALK MODE

1)Press TALK/FLASH.

2)Press CIDs. The summary screen appears.

3)View the Caller ID message you want to dial.

4)Press SELECT/CH. The displayed phone number will be dialed.

TIPS

You cannot make a call from the Caller ID list if your phone is connected to a private branch exchange (PBX).

When a long distance call has been set, “1” appears in the display.

If a call comes in via a telephone system that does not offer Caller ID service, no information is stored.

33

ID ALLERC

TIPS

You cannot store a Caller ID message in the Phonebook if a phone number does not appear in the message.

You cannot set the Distinctive Ring or Speed dial in this step. If you would like to set these options, edit the stored data.

Even if the memory locations are full, the message will

be stored in the Phonebook, however, the message will be erased from the Caller ID List.

If data is already stored in the One Touch Dial, the old data will be overwritten by the new data.

34

LONGDISTANCECALLS AND

AREACODESETTING/CANCELLATION

While the incoming Caller ID information is displayed, pressing /TONE will place or remove the prefix “1” in the display to set the call for a long distance call, or pressing # will set or cancel an area code. (See page 5.)

STORINGCALLERID MESSAGES IN THE

PHONEBOOK/ONETOUCHDIAL

Messages shown in the Caller ID list can be stored in the Phonebook. Using the incoming call information (i.e., Caller ID list), the phone number of the party on the Caller ID list can be stored in memory.

1)When the phone is in the standby mode, while the incoming Caller ID information is displayed, press /tSPEED.

2) Press ▲ or ▼ to choose “Store in PB?” (Phonebook

locations) or “Store in

SD?” (One Touch Dial location). To cancel Storing, select “Cancel”.

3)Press SELECT/CH. You will hear a confirmation tone.

CALLWAITINGDELUXEFEATURES

Your CT12 gives you new options for Call Waiting. At the touch of a button, you can place the caller on hold, send them to your voice mail service, or conference them into your current call. You may be required to subscribe to Call Waiting and Call Waiting Deluxe to use these features. Not all features are available in all areas. Check with your local telephone company for details.

1)When you receive a Call Waiting call, press MENU/MUTE for a list of options.

2)Press ▲ or ▼, or the number keypad (1– 7) to select an option. For example:

Press ▼ 4 times

Press ▼ 2 times

TIPS

To activate features, select “CW Deluxe On” in the Caller ID setup. See page 3.

You can also answer a waiting call immediately by pressing

TALK/FLASH, the first caller will be placed on hold. To return to the original caller, press

TALK/FLASH

again.

3)Press SELECT/CH. A confirmation screen will appear.

35

ID ALLERC

MORE

CHANGING THEDIGITALSECURITYCODE

TIPS

If you have not pressed any key for 30 seconds while in the deregistering operation, the phone returns to the standby mode.

If you receive an incoming call, page, or charge the remote while in de-registeringoperation,

or press

TALK/FLASH or END,the operation is canceled.

The digital security code is an identification code used to connect the remote and the base unit. Normally, setting the code is not necessary. In the rare situation that you suspect another cordless telephone is using the same security code, you can change the code. To change the digital security code, deregister the code, then register a different code.

DE-REGISTERTHESECURITYCODE

1)Remove the remote from the base. In the standby mode, press and hold DELETE andEND for about 10 seconds until you hear a confirmation tone.“De-Register?”appears.

2)Press ▲ to select “Yes”, then SELECT/CH. You will hear a confirmation tone, and “Deregistration Complete” appears.

36

REGISTER THESECURITYCODE

1)Unplug the AC adapter. Do not replace the remote to the base.

2)Press and hold PAGE on the base, while you plug in the AC Adapter, hold page until theCHARGE/IN USE LED on the base flashes.

3)Press TALK/FLASH. “Remote Registering” appears. When the registration operation is finished “Registration Complete” appears and theCHARGE/IN USE LED is no longer illuminated. You will hear a confirmation tone and the phone returns to the standby mode.

TIPS

You must complete the registration operation within 30 seconds, or the phone returns to the standby mode.

During the registration operation, you cannot receive an incoming call, page, or make

a call.

OREM

37

TIP

You can charge the remote with or without the beltclip.

38

INSTALLING THEBELTCLIP

TOATTACH THEBELTCLIP

Insert the beltclip into the holes on each side of the remote. Press down.

TOREMOVE

THE BELTCLIP

Pull one side of the beltclip to release the tab from the hole.

NOTE ONPOWERSOURCES

OUT OFRANGEWARNING

If you walk away from the base unit you will eventually exceed the maximum operating range for the CT12 cordless headset system. Any active call will be suspended and a double beep will sound in your headset every 10 seconds to warn you that you are out of range. The double beep will cease once you return within range and any active call will be taken off mute allowing you to resume your conversation.

LOWBATTERYWARNING

When the headset is running low (approx. 5 minutes talk time remaining), an audible warning will be heard through the headset as a single beep repeating every 10 seconds. Soon after hearing this warning, you should recharge the remote pack.

TIP

It is strongly advised that you avoid walking out of range when on an active call as you may find the call takes some time to reestablish after returning into range.

OREM

39