Pioneer S-DV262SW, S-DV262T, S-DV161, XV-DV262, HTZ262DVD User Manual

...
4.5 (2)
Pioneer S-DV262SW, S-DV262T, S-DV161, XV-DV262, HTZ262DVD User Manual

Operating Instructions

S002_En
D3-4-2-1-4_A_En
D3-4-2-1-7c_A_En
D3-4-2-1-7b_A_En
D3-4-2-1-7a_A_En
D3-4-2-1-3_A_En

Thank you for buying this Pioneer product.

Please read through these operating instructions so that you will know how to operate your model properly. After you have finished reading the instructions, put them in a safe place for future reference .

Location: bottom of the unit

IMPORTANT

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

CAUTION:

TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

D3-4-2-1-1_En-A

WARNING

This equipment is not waterproof. To prevent a fire or shock hazard, do not place any container filed with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain or moisture.

WARNING

To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the equipment.

VENTILATION CAUTION

When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 10 cm at top, 10 cm at rear, and 10 cm at each side).

WARNING

Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the equipment on thick carpet or a bed.

Operating Environment

Operating environment temperature and humidity: +5 ºC to +35 ºC (+41 ºF to +95 ºF); less than 85 %RH (cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light)

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause a fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest PIONEER authorized service center or your dealer for a replacement.

WARNING

Before plugging in for the first time, read the following section carefully.

The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit will be used meets the required voltage (e.g., 230 V or 120 V) written on the rear panel.

CAUTION

The STANDBY/ON switch on this unit will not completely shut off all power from the AC outlet. Since the power cord serves as the main disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power. Therefore, make sure the unit has been installed so that the power cord can be easily unplugged from the AC outlet in case of an accident. To avoid fire hazard, the power cord should also be unplugged from the AC outlet when left unused for a long period of time (for example, when on vacation).

D3-4-2-2-2a_A_En

D3-4-2-2-1a_A_En
K041_En

CAUTION

This product is a class 1 laser product, but this product contains a laser diode higher than Class 1. To ensure continued safety, do not remove any covers or attempt to gain access to the inside of the product. Refer all servicing to qualified personnel.

The following caution label appears on your unit. Location: top of the unit

[Taiwanese model]

CAUTION : CLASS 3B VISIBLE AND INVISIBLE LASER

RADIATION WHEN OPEN, AVOID

EXPOSURE TO THE BEAM.

VRW2159

[All other models]

CLASS 1

LASER PRODUCT

D3-4-2-1-8_B_En

This product is for general household purposes. Any failure due to use for other than household purposes (such as long-term use for business purposes in a restaurant or use in a car or ship) and which requires repair will be charged for even during the warranty period.

If the AC plug of this unit does not match the AC outlet you want to use, the plug must be removed and appropriate one fitted. Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. If connected to an AC outlet, the cut-off plug can cause severe electrical shock. Make sure it is properly disposed of after removal.

The equipment should be disconnected by removing the mains plug from the wall socket when left unused for a long period of time (for example, when on vacation).

Contents

01 Controls and displays

Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Remote control . . . . . . . . . . . . . . . . . . . . . . . . 7 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

02 Getting started

Home theater sound setup . . . . . . . . . . . . . . 10 Setting the channel levels . . . . . . . . . . . . . 10 Using the on-screen displays . . . . . . . . . . . . 11

Playing discs . . . . . . . . . . . . . . . . . . . . . . . . 11

Basic playback controls . . . . . . . . . . . . . . . 11 Resume and Last Memory . . . . . . . . . . . . . 12 DVD-Video disc menus. . . . . . . . . . . . . . . . 12 Video CD/Super VCD PBC menus . . . . . . . 12

Listening to the radio . . . . . . . . . . . . . . . . . . 13

Improving poor FM reception . . . . . . . . . . . 13

Memorizing stations. . . . . . . . . . . . . . . . . . 13

Listening to station presets . . . . . . . . . . . . 13 Listening to other sources . . . . . . . . . . . . . . 13 Setting the sleep timer . . . . . . . . . . . . . . . . . 14

Dimming the Display . . . . . . . . . . . . . . . . . . 14

03 Listening to your system

Auto listening mode . . . . . . . . . . . . . . . . . . . 15

Listening in surround sound . . . . . . . . . . . . . 15

Using Front Surround . . . . . . . . . . . . . . . . . . 15

Using Extra Power mode. . . . . . . . . . . . . . . . 16

Listening in stereo . . . . . . . . . . . . . . . . . . . . 16

Listening with headphones . . . . . . . . . . . . 16

Using the SFC modes . . . . . . . . . . . . . . . . . . 16

Adjusting the bass and treble . . . . . . . . . . . . 16 Boosting the bass level . . . . . . . . . . . . . . . . . 16

04 Disc playback features

Scanning discs . . . . . . . . . . . . . . . . . . . . . . . 17

Playing in slow motion . . . . . . . . . . . . . . . . . 17 Frame advance/frame reverse . . . . . . . . . . . . 17 Playing a JPEG slideshow . . . . . . . . . . . . . . . 17 Browsing DVD or Video CD/Super VCD discs with the Disc Navigator. . . . . . . . . . . . . . . . . . . . . 18

Browsing WMA, MP3, MPEG-4 AAC, DivX video and JPEG files with the Disc Navigator . . . . . 19

Using Playlists. . . . . . . . . . . . . . . . . . . . . . . . 19

Programming playlists . . . . . . . . . . . . . . . . 19 Listening to playlists . . . . . . . . . . . . . . . . . . 20 Clearing files from a playlist . . . . . . . . . . . . 20 Looping a section of a disc . . . . . . . . . . . . . . 20

Using repeat play . . . . . . . . . . . . . . . . . . . . . 20 Using random play . . . . . . . . . . . . . . . . . . . . 20

Creating a program list . . . . . . . . . . . . . . . . . 21 Other functions available from the program menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Searching a disc . . . . . . . . . . . . . . . . . . . . . . 22 Switching subtitles . . . . . . . . . . . . . . . . . . . . 22

Switching language/audio channels . . . . . . . 22

Zooming the screen . . . . . . . . . . . . . . . . . . . 22

Switching camera angles . . . . . . . . . . . . . . . 23 Displaying disc information. . . . . . . . . . . . . . 23

05 USB playback

Using the USB interface . . . . . . . . . . . . . . . . 24 Basic playback controls . . . . . . . . . . . . . . . . 24

Scanning files . . . . . . . . . . . . . . . . . . . . . . . . 25

Playing a JPEG slideshow . . . . . . . . . . . . . . . 25 Browsing files with the Navigator . . . . . . . . . 25

4

En

06 Audio Settings and Video Adjust menus

Audio Settings menu. . . . . . . . . . . . . . . . . . . 26 Audio DRC . . . . . . . . . . . . . . . . . . . . . . . . . 26 Video Adjust menu . . . . . . . . . . . . . . . . . . . . 26

07 Initial Settings menu

Using the Initial Settings menu . . . . . . . . . . . 27

Video Output settings . . . . . . . . . . . . . . . . . . 27 Language settings. . . . . . . . . . . . . . . . . . . . . 27 Display settings. . . . . . . . . . . . . . . . . . . . . . . 28 Options settings . . . . . . . . . . . . . . . . . . . . . . 28 Speakers settings . . . . . . . . . . . . . . . . . . . . . 28

Parental Lock . . . . . . . . . . . . . . . . . . . . . . . 29

About DivX® VOD content . . . . . . . . . . . . . 29

Speaker Distance . . . . . . . . . . . . . . . . . . . . 30

08 Other connections

Connecting external antennas. . . . . . . . . . . . 31 Connecting auxiliary audio components . . . . 31

Line Out options . . . . . . . . . . . . . . . . . . . . . 31

Connecting the S-video output . . . . . . . . . . . 32 Connecting using the component video

output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

About progressive scan video . . . . . . . . . . . 32 About control out connections . . . . . . . . . . . 33

09 Additional information

Disc/content format playback

compatibility . . . . . . . . . . . . . . . . . . . . . . . . . 34

Disc compatibility table. . . . . . . . . . . . . . . . 34 About DVD+R/DVD+RW compatibility. . . . 35

About DivX . . . . . . . . . . . . . . . . . . . . . . . . . 35 About MPEG-4 AAC. . . . . . . . . . . . . . . . . . . 36 About WMA . . . . . . . . . . . . . . . . . . . . . . . . 36

Using and taking care of discs. . . . . . . . . . . . 36

DVD Video regions . . . . . . . . . . . . . . . . . . . 37

Installation and maintenance . . . . . . . . . . . . 37

Hints on installation . . . . . . . . . . . . . . . . . . 37

Cleaning the pickup lens. . . . . . . . . . . . . . . 37 Problems with condensation. . . . . . . . . . . . 37 Moving the system unit . . . . . . . . . . . . . . . . 37 Screen sizes and disc formats . . . . . . . . . . . . 37

TV system setting. . . . . . . . . . . . . . . . . . . . . . 38

Frequency step setting. . . . . . . . . . . . . . . . . . 38 Switching off the demo . . . . . . . . . . . . . . . . . 38

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . 39 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

DVD/CD/Video CD player. . . . . . . . . . . . . . . 40

Tuner. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 USB connection . . . . . . . . . . . . . . . . . . . . . 41 Error Messages . . . . . . . . . . . . . . . . . . . . . . 41 Resetting the system . . . . . . . . . . . . . . . . . . . 42 Setting the Key Lock . . . . . . . . . . . . . . . . . . . 42

Using the language code list . . . . . . . . . . . . . 42

Language code list. . . . . . . . . . . . . . . . . . . . . 43

Country/Area code list . . . . . . . . . . . . . . . . . . 43

Specifications . . . . . . . . . . . . . . . . . . . . . . . . 44

Español Nederlands Italiano Français Deutsch English

5

En

01 Controls and displays

Chapter 1

Controls and displays

Front panel

OPEN/CLOSE

DVD/CD

 

USB

VOLUME

3

4

5

6

7

STANDBY/ON

 

 

 

 

PLAY LIST 1

PLAY LIST 2

PLAY LIST 3

 

 

1 2

10 11

8 9

1 STANDBY/ON

Switches the system on or into standby.

2 PLAY LIST buttons

Add tracks (during playback), or select a playlist (while stopped) (page 19).

3OPEN/CLOSE

Opens/closes the disc tray.

4DVD/CD

Selects the DVD/CD function and starts/ pauses/resumes playback.

5

Stops playback.

6 USB

Selects the USB function and starts/pauses playback.

7VOLUME +/– buttons

8USB interface

Connect a USB device for playback (see USB playback on page 24).

9PHONES jack

Connect headphones.

10Remote Sensor

11Display

See Display below.

6

En

Controls and displays

01

Remote control

 

STANDBY

DVD/CD

TUNER

 

1

/ON

(FM/AM)

 

 

 

 

 

2

 

USB

LINE

OPEN/CLOSE

 

 

 

11

 

 

 

 

PLAYLIST

 

1

2

3

1

 

 

AUDIO

SUBTITLE

 

3

4

5

6

2

 

ANGLE

ZOOM

12

 

7

8

9

3

 

 

SLEEP

 

EXTRAPWR

 

CLEAR

 

DISPLAY

 

 

0

 

13

 

TOPMENU

TUNE

 

MENU

4

 

 

 

14

5

ST

ENTER

ST

 

HOME

 

 

 

 

MENU

 

 

RETURN

6

 

TUNE

 

15

 

 

 

 

7

SETUP

TESTTONE

SURROUND

SOUND

 

 

 

 

8

 

 

 

 

 

 

TV CONTROL

 

LINEOUT

9

 

 

 

16

INPUT

CHANNEL

VOLUME

MUTE

 

 

 

 

17

10

SHIFT

 

VOLUME

18

 

 

 

 

 

1 STANDBY/ON

Switches the system on or into standby.

2 Function select buttons

Selects the source you want to listen to (DVD/ CD, TUNER, USB, LINE).

3 Number buttons, CLEAR, DISPLAY, SLEEP and DVD controls

CLEAR

Clears an entry.

DISPLAY

Displays/changes disc information shown on-screen (page 23).

SHIFT+SLEEP

Press to set the sleep timer (page 14).

SHIFT+AUDIO

Selects audio channel/language (page 22).

SHIFT+SUBTITLE

Displays/changes the subtitles (page 22).

SHIFT+ANGLE

Changes camera angle during DVD multiangle scene playback (page 23).

SHIFT+ZOOM

Changes the screen zoom level (page 22).

4 TOP MENU

Displays the top menu of a DVD disc in the play position — this may be the same as pressing MENU (page 12).

5 Cursor buttons, ENTER and tuning buttons

Cursor buttons

Use the cursor buttons (/ / /) to navigate on-screen displays and menus.

ENTER

Selects an option or executes a command.

TUNE +/–

Tunes the radio.

ST +/–

Selects station presets when listening to the radio.

6 HOME MENU

Displays (or exits) the on-screen menu for Initial Settings, Play Mode functions, etc.

7Setup and other sound controls

SETUP

Use to make various system and surround sound settings (page 10, 13 and 38).

TEST TONE

Outputs the test tone (for speaker setup) (page 10).

SURROUND

Selects a Surround mode (page 15) or switches to stereo playback (page 16).

Español Nederlands Italiano Français Deutsch English

7

En

01 Controls and displays

SOUND

Accesses the sound menu to adjust the SFC Mode, bass and treble, etc. (page 16).

8 Playback controls

See Basic playback controls on page 11, Disc playback features on page 17 and USB playback on page 24 for an explanation of these controls.

9 TV CONTROL buttons

These control Pioneer plasma televisions.

10 SHIFT

Press to access the controls highlighted in green.

11OPEN/CLOSE

Opens/closes the disc tray.

12PLAYLIST buttons

Add tracks (during playback), or select a playlist (while stopped) (page 19).

13 EXTRA PWR

Switches on the Extra Power mode (page 16).

14 MENU

Press to display a DVD disc or USB menu, or the Navigator (page 12 and 25).

15 RETURN

Returns to a previous menu screen.

16 LINE OUT

Cycle whether or not to output a downmixed signal from the LINE OUT terminal (page 31).

17 MUTE

Mutes the sound (press again to cancel).

18 VOLUME +/–

Adjusts the volume.

8

En

Controls and displays

Display

1

2

3

4

5

6

7

 

PRGSVE SOUND

 

REC MODE

 

DTS

F.SURR.

 

 

RPT -1

 

 

2D

 

 

 

kHz PGM

 

2PL

 

 

 

MHz RDM

 

15

14

13 12

11

1

DTS

 

 

 

Lights during playback of a DTS source

 

(page 15).

 

 

 

2

PRGSVE

 

 

 

Lights when progressive scan video output is

 

selected (page 32).

 

 

3

SOUND

 

 

 

Lights when the SFC Modes or the tone controls (treble, bass or bass boost) are active (page 16).

4 F.SURR.

Lights when either the Extra Power mode (page 16) or Front Sound listening mode is selected (page 15).

5 RPT and RPT-1

RPT lights during repeat play. RPT-1 lights during repeat one-track play (page 20).

6 REC MODE

Lights when Line Out mode is on (page 31).

7 PGM

Lights during program or playlist playback (page 19 and 21).

8 Tuner indicators

10 9 8

9 RDM

Lights during random play (page 20).

10 kHz/MHz

Indicates the frequency unit shown in the character display (kHz for AM, MHz for FM).

11Character display

12

Lights when sleep timer is active (page 14).

13

Lights during playback.

14 2PL II

Lights during Dolby Pro Logic II decoding (page 15).

15 2D

Lights during playback of a Dolby Digital source (page 15).

– Lights when a broadcast is being received.

– Lights when a stereo FM broadcast is being received in auto stereo mode.

– Lights when FM mono reception is selected.

01

Español Nederlands Italiano Français Deutsch English

9

En

02 Getting started

Chapter 2

Getting started

Home theater sound setup

Place your speakers as shown below for optimal surround sound (see the Speaker Setup Guide for more placement tips).

Standard surround 5-spot setup – This is a standard multichannel surround sound speaker setup for optimal 5.1 channel home theater sound.

Front left

Center

Front right

 

Subwoofer

Listening position

 

Surround

 

Surround

left

 

right

HTZ161DVD only:

Depending on the size and characteristics of your room, you can choose to use the following

setup option:1

After placing your speakers, complete Setting the channel levels below then refer to Speakers settings on page 28 to complete your surround sound setup.

Setting the channel levels

Set the relative channel levels from your main listening position.2

1 Press TEST TONE.

The test tone is output in the following order (from the speakers active in the current listening mode):

L – Front left speaker

C – Center speaker

R – Front right speaker

SR – Right surround speaker

SL – Left surround speaker

SW – Subwoofer3

Front surround 3-spot setup – This setup is ideal when rear surround speaker placement isn’t possible or you want to avoid running long speaker cables in your listening area. Use this setup together with the Front Surround modes to take advantage of wall and ceiling reflections for a very realistic surround effect.

 

 

 

Center

Front

 

 

 

 

 

 

 

 

Front

 

 

 

 

 

 

 

 

left

 

 

 

 

 

 

 

 

right

 

 

 

 

 

 

 

 

 

 

 

 

Subwoofer

Surround

 

 

 

Surround

 

left

 

 

 

 

right

Listening position

2Use the VOLUME +/– button to adjust the volume to an appropriate level.

3Use / to adjust the speaker levels in turn.

You should hear the test tone at the same volume from each speaker when seated in the main listening position. The channel level range is ±10 dB.

4When you’re done, press ENTER to exit test tone setup.

Note

1When using this setup, make sure the front surround mode is switched on (page 15) before selecting any surround mode.

2• This is only available when DVD/CD is selected and playback is stopped. Also make sure headphones are unplugged.

To adjust the overall balance while listening to any sound source you want, press SETUP, use /to select CH LEVEL then press ENTER. Use / to move channel to channel, and / to adjust the channel levels. Press ENTER when you’re finished.

3Since the subwoofer produces ultra-low frequencies its sound may seem quieter than it actually is.

10

En

Getting started

Using the on-screen displays

For ease of use, this system makes extensive use of graphical on-screen displays (OSDs).

All the screens are navigated in basically the same way, using , , , to change the highlighted item and pressing ENTER to select

it.1

Important

Throughout this manual, ‘Select’ means use the cursor buttons to highlight an item on-screen, then press ENTER.

Button What it does

HOME Displays/exits the on-screen display

MENU

Changes the highlighted menu item

ENTER Selects the highlighted menu item

RETURN Returns to the main menu without saving changes

Tip

The button guide at the bottom of every OSD screen shows you which buttons you’ll need to use for that screen.

Playing discs

The basic playback controls for playing DVD, CD, Video CD/Super VCD, DivX video and WMA/MP3/MPEG-4 AAC discs are covered here. Further functions are detailed in chapter 4.

1If the player isn’t already on, switch it on.

If you’re playing a disc with video, also turn on your TV and make sure that it is set to the correct video input.

2Press OPEN/CLOSE to load a disc.

Load a disc with the label side facing up, using the disc tray guide to align the disc (if you’re loading a double-sided DVD disc, load it with the side you want to play face down).

3 Press (play) to start playback.

If you’re playing a DVD or Video CD/Super VCD, a menu may appear. See DVD-Video disc menus and Video CD/Super VCD PBC menus on page 12 to navigate these.

If you loaded a disc containing JPEGs, a slideshow will start. See Playing a JPEG slideshow on page 17 for more on this.

If a disc contains a mixture of DivX video and other media file types (MP3, for example), first select whether to play the DivX video files (DivX) or the other media file types (MP3/WMA/JPEG/MPEG-4 AAC) from the on-screen display.

4 Adjust the volume.

Use the VOLUME control.

Basic playback controls

The following table shows the basic controls on

the remote for playing discs2. You can find other playback features in the chapter 4.

Button What it does

Starts/resumes normal playback.

If the display shows RESUME or LAST MEM playback starts from the resume or last memory point (see

Resume and Last Memory below).

Pauses/unpauses a disc.

Stops playback or cancels the resume function (if the display shows RESUME).

Note

1The screen saver will appear after five minutes of inactivity.

2You may find with some DVD discs that some playback controls don’t work in certain parts of the disc.

02

Español Nederlands Italiano Français Deutsch English

11

En

02 Getting started

Button What it does

Press to start fast reverse scanning.

Press to start fast forward scanning.

Skips to the start of the current track or chapter, then previous tracks/chapters.

Skips to the next track or chapter.

Numbers Use to enter a title/chapter/track number. Press ENTER to select.

If the disc is stopped, playback starts from the selected title (for DVD) or track (for CD/Video CD/Super VCD).

If the disc is playing, playback jumps to the start of the selected title (VR mode DVD-R/-RW), chapter (DVDVideo) or track (CD/Video CD/Super VCD).

Resume and Last Memory

When you stop playback of a disc, RESUME shows in the display indicating that you can resume playback from that point.

With DVDs and Video CD/Super VCDs, even if

ejected, the play position is stored in memory.1 The next time you load the disc, the display shows LAST MEM and you can resume playback.

If you want to clear the resume point, press(stop) while RESUME is displayed.

Button

What it does

 

 

MENU Displays a DVD disc menu—this varies with the disc and may be the same as the ‘top menu’.

Moves the cursor around the screen.

ENTER Selects the current menu option.

RETURN Returns to the previously displayed menu screen.

Numbers Highlights a numbered menu option (some discs only). Press ENTER to select.

Video CD/Super VCD PBC menus

Some Video CD/Super VCDs have menus from which you can choose what you want to watch. These are PBC (Playback control) menus.

You can play a PBC Video CD/Super VCD without having to navigate the PBC menu by starting playback using a number button to select a track, rather than the (play) button.

Button

What it does

 

 

RETURN Displays the PBC menu.

Numbers Selects numbered menu options. Press ENTER to select.

Displays the previous menu page (if there is one).

DVD-Video disc menus

Many DVD-Video discs contain menus from which you can select what you want to watch.

Sometimes DVD-Video menus are displayed automatically when you start playback; others only appear when you press MENU or TOP MENU.

Displays the next menu page (if there is one).

Button

What it does

 

 

TOP MENU Displays the ‘top menu’ of a DVD disc — this varies with the disc.

Note

1• The Last Memory function may not work with some discs.

• For DVD-Video discs (except VR mode DVD-R/-RW), the player stores the play position of the last five discs.

12

En

Getting started

02

Listening to the radio

The tuner can receive both FM and AM broadcasts, and lets you memorize your favorite stations so you don’t have to manually tune in every time you want to listen.

1Press TUNER to switch to the tuner, then press repeatedly to select the AM or FM band.

The display shows the band and frequency.

2Tune to a frequency.

There are three tuning modes — manual, auto, and high-speed:

Manual tuning: Press TUNE +/– repeatedly to change the displayed frequency.

Auto tuning: Press and hold TUNE +/– until the frequency display starts to move, then release. The tuner will stop on the next station it finds. Repeat to keep searching.

High-speed tuning: Press and hold

TUNE +/– until the frequency display starts to move rapidly. Keep the button held down until you reach the frequency you want. If necessary, fine tune the frequency using the manual tuning method.

Improving poor FM reception

If you’re listening to an FM station in stereo but the reception is weak, you can improve the sound quality by switching to mono.

1Tune to an FM radio station then press SETUP.

2Use /to choose FM MODE then press

ENTER.

3Use / to select FM MONO then press

ENTER.

The mono indicator () lights when the tuner is in mono reception mode.

Select FM AUTO above to switch back to autostereo mode (the stereo indicator ( ) lights when receiving a stereo broadcast).

Memorizing stations

You can save up to 30 station presets so that you always have easy access to your favorite stations without having to tune in manually each time.

1 Tune to an AM or FM radio station.

For the FM band, select mono or auto-stereo reception as necessary. This setting is saved along with the preset.

2Press SETUP and use / to choose

‘ST.MEM.’ then press ENTER.

3Use / to select the station preset you want then press ENTER.

Listening to station presets

1Make sure the TUNER function is selected.

2Use the ST +/– buttons to select a station preset.

You can also use the number buttons to do this.

Listening to other sources

You can connect auxiliary sources (TV, satellite receiver, etc.) to this unit for playback through the speaker system. See Connecting auxiliary audio components on page 31 for more on this.

To connect a USB device to the USB terminal, see USB playback on page 24.

1Make sure that the external source (TV, satellite receiver, etc.) is switched on.

2Press LINE to select the source.

3If necessary, start playback of the source.

Español Nederlands Italiano Français Deutsch English

13

En

02 Getting started

Setting the sleep timer

The sleep timer switches off the system after about an hour so you can fall asleep without

worrying about it.1

• Press SHIFT+SLEEP repeatedly to select an option then press ENTER.

Choose between the following options:

SLP ON – Switches off after about an hour

SLP OFF – Cancels the sleep timer

After selecting SLP ON, you can press SHIFT+SLEEP again to check how much time is left. Each line indicates approximately 12 minutes (remaining):

S L P - - - - -

Dimming the Display

You can adjust the brightness of the text in the front panel display.

1Press SETUP and use / to choose

DIMMER then press ENTER.

This is shown in the front panel display.

2Use / to select LIGHT or DARK then press ENTER.

Note

1 The display dims when the sleep timer is set.

14

En

Listening to your system

Chapter 3

Listening to your system

Auto listening mode

The Auto listening mode is the simplest way to listen to any source as it was mastered: the output from the speakers mirrors the channels in the source material.

• Press SURROUND to select the AUTO listening mode.1

Using Front Surround

HTZ161DVD only

The Front Surround mode is effective when

DVD/CD or USB is selected as the input source and you are using the Front surround 3-spot speaker setup as described in Home theater sound setup on page 10 and the Speaker Setup Guide.

Listening in surround sound

You can listen to stereo or multichannel

sources in surround sound.2 Surround sound is generated from stereo sources using one of the Dolby Pro Logic decoding modes.

Press SURROUND repeatedly to select a

listening mode.1

The choices that appear in the display will vary according to the type of source that’s playing.

AUTO – Auto listening mode (see above)

DOLBY PL (Dolby Pro Logic) – 4.1 channel surround sound (use with any two-channel source)

MOVIE (Dolby Pro Logic II Movie) – Pro Logic II 5.1 channel surround sound, especially suited to movie sources (use with any two-channel source)

MUSIC (Dolby Pro Logic II Music) – Pro Logic II 5.1 channel surround sound, especially suited to music sources (use with any two-channel source)

STEREO – See Listening in stereo below

• The surround speakers should be placed on top of the front speakers and oriented towards the walls.

1Press SETUP and use / to choose

F.SURR then press ENTER.3

2Use to / select MODE ON or MODE

OFF then press ENTER.4

After selecting MODE ON, you can use the

surround listening modes with Front Surround.

Note

1If the source is Dolby Digital or DTS, the corresponding indicator lights in the front panel display.

2Note that the input source must be switched to DVD/CD or USB for multichannel playback.

3Note that the F.SURR option does not appear when headphones are connected.

4• When set to MODE ON, make sure to follow the Setup Guide for best surround sound.

When you have Extra Power set to MODE ON and then change Front Surround to MODE OFF, the Listening Mode is automatically switched to AUTO.

03

Español Nederlands Italiano Français Deutsch English

15

En

03 Listening to your system

Using Extra Power mode

Extra Power mode allows you to enjoy richer,

fuller sound from stereo (2.1ch) sources.1 Extra Power mode is available when listening to DVD/CD or USB sources.

For HTZ161DVD:

The surround speakers should be placed on top of the front speakers, with all speakers facing forwards.

For HTZ262DVD:

The front and surround speakers should be placed next to one another, with all speakers facing forwards.

Press EXTRA PWR to select MODE ON or

MODE OFF.2

After selecting MODE ON, the F.SURR. indicator lights on the front panel display.

Using the SFC modes

The SFC (Sound Field Control) modes can be used with any multichannel or stereo source for a variety of additional surround sound effects.

1Press SOUND.

2Use / to select SFC MODE then press

ENTER.

3Press / then ENTER to select an SFC

Sound Mode.

Select between OFF, ACTION, DRAMA,

ROCK, POP, HALL or LIVE.

Adjusting the bass and treble

Use the bass and treble controls to adjust the overall tone.

1 Press SOUND.

Listening in stereo

You can listen to any source — stereo or multichannel — in stereo. When playing a multichannel source, all channels are downmixed to the front left/right speakers and the subwoofer.

• Press SURROUND repeatedly until STEREO shows in the display.

Listening with headphones

When headphones are connected, only the STEREO mode is available.

2Use / to select BASS or TREBLE then press ENTER.

3Use / to adjust the sound then press

ENTER to confirm.

Boosting the bass level

There are two bass modes you can use to enhance the bass in a source.

1Press SOUND.

2Use /to select BASSMODE then press

ENTER.

3Use / to adjust the sound then press

ENTER to confirm.

Select between OFF, MUSIC or CINEMA.

Note

1When the Extra Power mode is on, most sound features cannot be used. The display will briefly blink EXTRAPWR if you try and use a prohibited function while the Extra Power mode is on.

2• Note that you cannot use Extra Power mode when using headphones. If you press EXTRA PWR when headphones are connected, a CANNOT error message appears on the front panel display.

When set to MODE ON, make sure to follow the Setup Guide for best surround sound.

When set to MODE OFF, the listening mode is automatically set to AUTO.

16

En

Disc playback features

Chapter 4

Disc playback features

Important

Many of the functions covered in this chapter apply to DVD discs, Video CDs/ Super VCDs, CDs, DivX video and WMA/ MP3/MPEG-4 AAC/JPEG discs, although the exact operation of some varies slightly with the kind of disc loaded.

Some DVDs restrict the use of some functions (random or repeat, for example) in some or all parts of the disc. This is not a malfunction.

When playing Video CD/Super VCDs, some of the functions are not available during PBC playback. If you want to use them, start the disc playing using a number button to select a track.

1During playback, press (pause).

2Press and hold /or /until slow motion playback starts.

Press repeatedly to change the slow motion speed (shown on-screen).

To resume playback, press (play).2

Frame advance/frame reverse

You can advance or back up DVD discs frame- by-frame. With Video CD/Super VCDs and DivX video you can only use frame advance.

1During playback, press (pause).

2Press / or / to reverse or advance a frame at a time.

To resume playback, press (play).2

Scanning discs

 

Playing a JPEG slideshow

You can fast-scan discs forward or backward at

various different speeds.1

After loading a disc containing JPEG pictures,

 

press to start a slideshow from the first

• During playback, press or to start scanning.

Press repeatedly to increase the scanning speed (shown on-screen).

• To resume playback, press (play).2

Playing in slow motion

You can play DVDs, Video CD/Super VCDs and DivX video at four different forward slow motion speeds. DVD discs can also be played in reverse slow motion.

folder/picture on the disc.3 The player displays the pictures in each folder in alphabetical order.

If the disc contains WMA/MP3/MPEG-4 AAC files, playback of the slideshow and audio files repeats. During audio playback, you can still use the skip ( / ), scan ( / ) and pause ( ) functions.

Pictures are automatically adjusted so that they fill as much of the screen as possible.

Note

1Only one speed is available for DivX video discs.

2• Depending on the disc, normal playback may automatically resume when a new chapter is reached on a DVD disc.

For Video CDs/Super VCDs in PBC mode and WMA/MP3/MPEG-4 AAC tracks (in Scan Mode only), normal playback resumes when you reach the beginning or the end of a track.

3• The time it takes for the player to load a file increases with large file sizes.

Discs can contain up to 299 folders and up to 648 folders and files combined.

04

Español Nederlands Italiano Français Deutsch English

17

En

04 Disc playback features

While the slideshow is running:

The options available depend on the kind of

 

 

disc loaded and whether the disc is playing or

Button

What it does

not, but include:

 

 

Pauses the slideshow (or audio); • Title – Titles from a DVD-Video disc.

press again to restart.

Jumps to the previous picture (or audio file with audio playback).

Jumps to the next picture (or audio file with audio playback).

/ / / Pauses the slideshow and rotates/flips the displayed picture (Press (play) to restart slideshow).

SHIFT+ZOOM Pauses the slideshow and zooms the picture. Press again to toggle between 1x, 2x and 4x zoom (Press (play) to restart slideshow).

MENU Displays the Disc Navigator

screen (see below).

Chapter – Chapters from the current title of a DVD-Video disc.

Track – Tracks from a Video CD/Super VCD disc.

Time – Thumbnails from a Video CD/Super VCD disc at 10 minute intervals.

Original: Title – Original titles from a VR mode DVD-R/-RW disc.

Playlist: Title – Playlist titles from a VR mode DVD-R/-RW disc.

Original: Time – Thumbnails from the Original content at 10 minute intervals.

Playlist: Time – Thumbnails from the Playlist at 10 minute intervals.

The screen shows up to six moving thumbnail images displayed one after another. To display the previous/next six thumbnails, press /

.

Browsing DVD or Video CD/ Super VCD discs with the Disc Navigator

Use the Disc Navigator to browse through the contents of a DVD or Video CD/Super VCD disc to find the part you want to play.

1 During playback, press HOME MENU and select ‘Disc Navigator’ from the onscreen menu.

Disc Navigator

2 Select a view option.

Disc Navigator

Title

Chapter

3 Select the thumbnail image for what you want to play.

01

02

03

04

05

06

Disc Navigator: Title 0149: --

You can use either / / / and ENTER to select a thumbnail, or the number buttons.

To select using the number buttons, enter a two-digit number then press ENTER.

18

En

Disc playback features

Browsing WMA, MP3, MPEG-4 AAC, DivX video and JPEG files with the Disc Navigator

Use the Disc Navigator to find a particular file or folder by filename.

1 Press HOME MENU and select ‘Disc Navigator’ from the on-screen menu.

00:00/ 00:00

0kbps

Folder1

Folder2

Folder3

Folder4

2 Use / / / and ENTER to navigate.

Use / to move up and down the folder/file list.

Use to return to the parent folder.1

Use ENTER or to open a highlighted folder.

When a JPEG file is highlighted, a thumbnail image is displayed on the right.

00:00/ 00:00

0kbps

Folder2

File1

File2

File3

File4

File5

3 To play the highlighted track or DivX video file or display the highlighted JPEG file, press ENTER.

When a WMA/MP3/MPEG-4 AAC or DivX video file is selected, playback begins from that file, and continues until the end of the folder.

When a JPEG file is selected, a slideshow begins, starting with that file, and continues to the end of the folder.

Tip

You can also play a JPEG slideshow while listening to WMA/MP3/MPEG-4 AAC playback. Simply select the audio file you want to listen to followed by the JPEG from which you want the slideshow to start. Playback of both the slideshow and the audio files repeats. Playback controls are effective for the JPEG slideshow only.

To play the contents of the whole disc rather than just the current folder, exit the Disc Navigator and start playback using the (play) button.

Using Playlists

With this feature, you can make up to three playlists of 30 files each for discs containing WMA, MP3, MPEG-4 AAC and JPEG files.

Since this unit will remember all playlists for the last ten discs you have loaded, this is useful for if you have a large number of files that you

want to organize quickly and easily.2

Programming playlists

1With the disc stopped, press HOME MENU and select ‘Disc Navigator’ from the on-screen menu.

2Select the file you want to add to the playlist.

See Browsing WMA, MP3, MPEG-4 AAC, DivX video and JPEG files with the Disc Navigator above if you don’t know how to do this.

3Press PLAY LIST 1, 2 or 3.

The file is added to the playlist you select.

4 Repeat steps 2 and 3 until you’re done.

Note

1You can also do this by going to the ‘..’ folder at the top, then pressing ENTER.

2The disc must be loaded for the files in your playlist to play back.

04

Español Nederlands Italiano Français Deutsch English

19

En

04 Disc playback features

Tip

To add files without the on-screen display, simply press PLAY LIST 1, 2 or 3 during normal playback of the file you want (except when a JPEG slideshow is playing at the same time as audio).

2Select ‘A-B Repeat’.

3Press ENTER on ‘A(Start Point)’ to set the loop start point.

4Press ENTER on ‘B(End Point)’ to set the loop end point.

After pressing ENTER, playback jumps back to the start point and plays the loop.

Listening to playlists

• With playback stopped, press PLAY LIST 1, 2 or 3.

During playback, PGM lights in the front panel display. If no playlist has been programmed, NO LIST shows in the display.

If the playlist contains both JPEG and audio files, playback of the slideshow and audio files starts.

5 To resume normal playback, select ‘Off’.

Using repeat play

In addition to various repeat play options, it’s also possible to use repeat play together with program play (see Creating a program list on page 21).

1 During playback, press HOME MENU and select ‘Play Mode’.

Clearing files from a playlist

2 Select ‘Repeat’ then select a repeat play

1Start playback of your playlist.

2From the ‘Disc Navigator’ screen, select the file you want to remove from the playlist and press CLEAR.

Looping a section of a disc

The A-B Repeat function allows you to specify two points (A and B) within a track (CD, Video CD/Super Video CD) or title (DVD) that form a loop which is played over and over.

1 During playback, press HOME MENU and select ‘Play Mode’.

Play Mode

option.1

If program play is active, select Program Repeat to repeat the program list, or Repeat Off to cancel.

For DVD discs, select Title Repeat or

Chapter Repeat.

For CDs and Video CD/Super VCDs, select

Disc Repeat or Track Repeat.

For DivX video discs, select Title Repeat

(or Repeat Off).

Using random play

Use this function to play titles or chapters (DVD-Video) or tracks (CD and Video CD/Super

VCD) in a random order.2

1 During playback, press HOME MENU and select ‘Play Mode’.

Note

1You can’t use repeat play with WMA/MP3/MPEG-4 AAC discs.

2• You can set the random play option when a disc is playing or stopped. However, you can’t use random play together with program play.

You can’t use random play with VR format DVD-R/-RW discs, WMA/MP3/MPEG-4 AAC discs, DivX video discs, or while a DVD disc menu is being displayed.

20

En

Disc playback features

04

2Select ‘Random’ then select an option.

For DVD discs, select Random Title or

Random Chapter.

For CDs and Video CD/Super VCDs, select On or Off to switch random play on or off.

Tip

Use the following controls during random play:

Button

What it does

 

 

Selects a new track/title/chapter at random.

Returns to the beginning of the current track/title/chapter; further presses select another random track/title/chapter.

4Repeat step 3 to build up a program list.

A program list can contain up to 24 steps.

You can insert steps by just highlighting the position where you want the new step to appear and entering a title/chapter/track number.

To delete a step, highlight it and press

CLEAR.

5To play the program list, press (play).

Program play remains active until you turn off program play (see below), erase the program list (see below), eject the disc or switch off.

Tip

Use the following controls during program play:

Button

What it does

 

 

• Random play remains in effect until you

 

HOME

Save the program list and exit

select Random Off from the random play

 

 

MENU

without starting playback.

menu options.

 

 

 

 

 

 

Skip to the next step in the

 

 

 

 

 

program list.

 

 

 

Creating a program list

This feature lets you program the play order of titles/chapters/tracks on a disc.1

1During playback, press HOME MENU and select ‘Play Mode’.

2Select ‘Program’ then select ‘Create/Edit’ from the list of program options.

3Use / / / and ENTER to select a title, chapter or track for the current step in the program list.

For a DVD disc, you can add a title or a chapter.

For a CD or Video CD/Super VCD, select a track to add to the program list.

After pressing ENTER to select the title/ chapter/track, the step number automatically moves down one.

Other functions available from the program menu

There are a number of other options in the program menu in addition to Create/Edit.

Playback Start – Starts playback of a saved program list

Playback Stop – Turns off program play, but does not erase the program list

Program Delete – Erases the program list and turns off program play

Note

1 You can’t use Program play with VR format DVD-R/-RW discs, WMA/MP3/MPEG-4 AAC discs, DivX video discs, or while a DVD disc menu is being displayed.

Español Nederlands Italiano Français Deutsch English

21

En

04 Disc playback features

Searching a disc

You can search DVD discs by title or chapter number, or by time; CDs and Video CD/Super VCDs by track number or time; DivX video discs by time.

1Press HOME MENU and select ‘Play Mode’.

2Select ‘Search Mode’.

The search options that appear depend on the kind of disc loaded.

3Select a search mode.

The disc must be playing in order to use time search.

4Use the number buttons to enter a title, chapter or track number, or a time.

For a time search, enter the number of minutes and seconds into the currently playing title (DVD/ DivX video) or track (CD/ Video CD/Super VCD) you want playback to resume from. For example, press 4, 5, 0, 0 to have playback start from 45 minutes into the disc. For 1 hour, 20 minutes and 30 seconds, press 8, 0, 3, 0.

5Press ENTER to start playback.

Switching subtitles

• Press SHIFT+SUBTITLE repeatedly to select a subtitle option.

To set subtitle preferences, see Language settings on page 27.

See Displaying DivX subtitle files on page 35 for more on DivX subtitles.

Switching language/audio channels

When playing discs recorded with dialog in two or more languages, or with dual-mono audio2 you can switch these during playback.3

• Press SHIFT+AUDIO repeatedly to select an audio language option.

To set audio language preferences, see

Language settings on page 27.

Zooming the screen

Using the zoom feature you can magnify a part of the screen by a factor of 2 or 4, while watching a DVD, DivX video title or Video CD/ Super VCD or playing a JPEG disc.

1During playback, press SHIFT+ZOOM to select the zoom factor (Normal, 2x or 4x).

2Use / / / to change the zoomed area.

Some DVD discs and DivX video discs have subtitles in one or more languages; the disc box will usually tell you which subtitle languages are available. You can switch

subtitle language during playback.1

You can change the zoom factor and the zoomed area freely during playback.4

Note

1Some discs only allow you to change subtitle language from the disc menu. Press TOP MENU or MENU to access.

2Some Super VCDs have two soundtracks. With these discs you can switch between the two soundtracks as well as individual channels in each.

3Some discs only allow you to change audio language from the disc menu. Press TOP MENU or MENU to access.

4• Since DVD, Video CD/Super VCD, DivX video title and JPEG pictures have a fixed resolution, picture quality will deteriorate, especially at 4x zoom. This is not a malfunction.

If the navigation square at the top of the screen disappears, press SHIFT+ZOOM again to display it.

22

En

Disc playback features

Switching camera angles

Some DVD discs feature scenes shot from two or more angles — check the disc box for details.

When a multi-angle scene is playing, a icon appears on screen (this can be switched off if you prefer — see Display settings on page 28).

• During playback (or when paused), press SHIFT+ANGLE to switch angle.

Displaying disc information

Various track, chapter and title information can be displayed on-screen during playback.

• To show/switch/hide the information displayed, press DISPLAY repeatedly.

Limited disc information also appears in the front panel display. Press DISPLAY to change the displayed information.

04

Español Nederlands Italiano Français Deutsch English

23

En

05 USB playback

Chapter 5

USB playback

Using the USB interface

It is possible to listen to two-channel audio1 and watch JPEG files using the USB interface on the front of this unit. Connect a USB mass

storage device2 as shown below.

1With the player switched on, press USB.

Make sure your TV is on and set to the correct video input.

2Connect your USB device.

The USB terminal is located on the front panel.

USB

(Type A)

USB mass storage device

Important

If a USB ERR message lights in the display, it may mean that the power requirements of the USB device are too high for this player, or that the device is incompatible. Try the following:

Switch the player off, then on again.

Reconnecting the USB device with the player switched off.

Selecting to another input source (like DVD/CD), then back to USB.

Using a dedicated AC adapter (supplied with the device) for USB power.

If this doesn’t remedy the problem, it is likely your USB device is incompatible.

Basic playback controls

The following table shows the basic controls on the remote for USB playback.

Button What it does

Starts normal playback.

Pauses/unpauses playback.

Stops playback.

3 Press (play) to start playback.

If your USB device contains JPEGs, a slideshow will start. See Playing a JPEG slideshow on page 25 for more on this.

Make sure USB DATA is showing in the front panel display (or the system is in standby) when disconnecting.

Press to start fast reverse scanning.

Press to start fast forward scanning.

Skips to the start of the current file, then previous files.

Skips to the next file.

Note

1This includes playback of WMA/MP3/MPEG-4 AAC files (except files with copy-protection or restricted playback). It is not possible to play DivX files through the USB terminal.

2• Compatible USB devices include external magnetic hard drives, portable flash memory (particularly keydrives) and digital audio players (MP3 players) of format FAT16/32. It is not possible to connect this unit to a personal computer for USB playback.

Pioneer cannot guarantee compatibility (operation and/or bus power) with all USB mass storage devices and assumes no responsibility for any loss of data that may occur when connected to this unit.

With large amounts of data, it may take longer for the system to read the contents of a USB device.

24

En

USB playback

Scanning files

You can fast-scan forward or backward at various different speeds.

• During playback, press or to start scanning.

Press repeatedly to increase the scanning speed (shown on-screen).

• To resume playback, press (play).1

Button

What it does

 

 

MENU Displays the Navigator screen (see below).

Browsing files with the Navigator

Use the Navigator to find WMA, MP3, MPEG-4 AAC and JPEG files or folders by name.3

1 Press MENU.

Playing a JPEG slideshow

Press to start a slideshow from the first

folder/picture.2 The pictures in each folder are displayed in order.

If the device contains WMA/MP3/MPEG-4 AAC files, playback of the slideshow and audio files repeats. During audio playback, you can still use the skip ( / ), scan ( / ) and pause ( ) functions.

Pictures are automatically adjusted so that they fill as much of the screen as possible.

While the slideshow is running:

Button

What it does

 

 

Pauses the slideshow (or audio); press again to restart.

Jumps to the previous picture (or audio file with audio playback).

Jumps to the next picture (or audio file with audio playback).

/ / / Pauses the slideshow and rotates/flips the current picture (Press to restart slideshow).

SHIFT+ZOOM Pauses the slideshow and zooms the picture. Press again to toggle between 1x, 2x and 4x zoom (Press to restart slideshow).

2 Use / / / and ENTER to navigate.

Use / to move up/down the folder/file list. Use to return to the parent folder.4

Use ENTER or to open a highlighted folder.

When a JPEG file is highlighted, a thumbnail image is displayed on the right.

3 To play the highlighted track or display the highlighted JPEG file, press ENTER.

When a WMA/MP3/MPEG-4 AAC file is selected, playback begins from that file, and continues until the end of the folder.

When a JPEG file is selected, a slideshow begins, starting with that file, and continues to the end of the folder.

Tip

You can also play a JPEG slideshow while listening to WMA/MP3/MPEG-4 AAC playback. Simply select the audio file you want to listen to followed by the JPEG from which you want the slideshow to start. Playback of both the slideshow and the audio files repeats. Playback controls are effective for the JPEG slideshow only.

To play all of the contents, rather than just the current folder, exit the Navigator and start playback using the (play) button.

Note

1With WMA/MP3/MPEG-4 AAC tracks, playback automatically resumes at the end or beginning of the track.

2• The time it takes for the player to load a file increases with large file sizes.

• USB devices can contain up to 299 folders and up to 648 folders and files combined.

3Filenames may be displayed incorrectly with some digital audio players.

4You can also do this by going to the ‘..’ folder at the top, then pressing ENTER.

05

Español Nederlands Italiano Français Deutsch English

25

En

06 Audio Settings and Video Adjust menus

Chapter 6

Audio Settings and Video Adjust menus

Audio Settings menu

The Audio Settings menu offers features for adjusting the way discs sound.

1 Press HOME MENU and select ‘Audio Settings’ from the on-screen display.

Audio Settings

2 Select and change settings using / / / and ENTER.

Audio Settings

Audio DRC

High

 

Medium

 

Low

 

Off

Audio DRC

Settings: High, Medium, Low,

Off (default)

When watching Dolby Digital DVDs at low volume, it’s easy to lose the quieter sounds completely — including some of the dialog. Switching Audio DRC (Dynamic Range Control) to on can help by bringing up the quieter sounds, while controlling loud peaks.

How much of a difference you hear depends on the material you’re listening to. If the material doesn’t have wide variations in volume, you

1 Press HOME MENU and select ‘Video Adjust’ from the on-screen display.

Video Adjust

2 Make settings using / / / and

ENTER.

Video Adjust

 

 

Sharpness

 

Standard

Brightness

 

0

Contrast

 

0

Gamma

 

Off

Hue

 

0

Chroma Level

 

0

 

 

 

You can adjust the following settings:

Sharpness – Adjusts the sharpness of edges in the picture (Fine, Standard, Soft)

Brightness – Adjusts the overall brightness (–20 to +20)

Contrast – Adjusts the contrast between light and dark (–16 to +16)

Gamma – Adjusts the ‘warmth’ of the picture (High, Medium, Low, Off)

Hue – Adjusts the red/green balance (Green 9 to Red 9)

Chroma Level – Adjusts how saturated colors appear (–9 to +9)

Adjust the Brightness, Contrast, Hue and Chroma Level settings using /.

may not notice much change.1

Video Adjust menu

From the Video Adjust screen you can adjust settings that affect picture presentation.

Brightness

min

max

0

 

 

 

 

3 Press ENTER to return to the Video Adjust screen, or HOME MENU to exit.

Note

1 Audio DRC is only effective with Dolby Digital audio sources.

26

En

Initial Settings menu

Chapter 7

Initial Settings menu

Using the Initial Settings menu

The Initial Settings menu provides audio and video output settings, parental lock settings, and display settings, among others.

If an option is grayed out it means that it cannot be changed at the current time. This is usually because a disc is playing. Stop the disc, then change the setting.

1Press DVD/CD.

2With playback stopped, press HOME MENU and select ‘Initial Settings’.

Initial Settings

3 Use / / / and ENTER to select the setting and option you want to set.

All the settings and options are explained on the following pages.1

Video Output settings

Setting

Option

What it means

TV Screen

4:3 (Letter Box)

Set if you have a conventional 4:3 TV. Widescreen movies are

(See also Screen sizes

 

shown with black bars top and bottom.

and disc formats on

 

 

4:3 (Pan & Scan)

Set if you have a conventional 4:3 TV. Widescreen movies are

page 37.)

 

shown with the sides cropped so that the image fills the screen.

 

 

 

 

 

 

16:9 (Wide)

Set if you have a widescreen TV.

 

 

 

Component Out

Interlace

Set if your TV is not compatible with progressive scan video.

(See also Connecting

 

 

Progressive

Set if your TV is compatible with progressive scan video (see

using the component

 

your TV’s instruction manual for details). Press ENTER once

video output on

 

 

more to confirm (or RETURN to cancel).

page 32.)

 

 

Note that progressive scan video is only output from the

 

 

component video jacks.

 

 

 

Language settings

07

Español Nederlands Italiano Français Deutsch English

Setting

Option

What it means

Audio Language

English /

If there is an English soundtrack on the disc, it is played.

 

English (Taiwanese model)

 

 

 

 

 

Languages as displayed /

If there is a language selected (or Chinese for the Taiwanese

 

Chinese (Taiwanese model)

model) on the disc, it is played.

 

 

 

 

Other Language

Select to choose a language other than the ones displayed (see

 

 

Using the language code list on page 42).

Note

1• In the table, the default setting is shown in bold: other settings are shown in italics.

Some settings, such as TV Screen, Audio Language and Subtitle Language may be overridden by the DVD disc. Often these settings can also be made from the DVD disc menu.

27

En

07 Initial Settings menu

Setting

Option

What it means

Subtitle Language

English /

If there are English subtitles on the disc they are displayed.

 

English (Taiwanese model)

 

 

 

 

 

Languages as displayed /

The subtitle language selected (or Chinese for the Taiwanese

 

Chinese (Taiwanese model)

model) on the disc is displayed.

 

 

 

 

Other Language

Select to choose a language other than the ones displayed (see

 

 

Using the language code list on page 42).

 

 

 

DVD Menu

w/Subtitle Lang.

DVD disc menus are displayed in the same language as your

Language

 

selected subtitle language, if possible.

 

 

 

 

Languages as displayed

DVD menus are displayed in the selected language, if possible.

 

 

 

 

Other Language

Select to choose a language other than the ones displayed (see

 

 

Using the language code list on page 42).

 

 

 

Subtitle Display

On

Subtitles are displayed in your selected subtitle language.

 

 

 

 

Off

Subtitles are always off by default when you play a DVD disc.

 

 

 

 

 

 

Display settings

Setting

Option

What it means

 

OSD Language

English /

On-screen displays are shown in English.

 

 

English (Taiwanese model)

 

 

 

 

 

 

Languages as displayed / On-screen displays are shown in the language selected (or

 

 

(Taiwanese model)

Chinese for the Taiwanese model).

 

 

 

 

 

 

 

 

Angle Indicator

On

A camera icon is displayed on-screen during multi-angle

 

 

 

scenes on a DVD disc.

 

 

 

 

 

 

Off

No multi-angle indication is shown.

 

 

 

 

 

 

 

 

 

Options settings

Setting

Option

What it means

 

Parental Lock

See Parental Lock below.

 

 

 

 

 

DivX(R) VOD

Display

See About DivX® VOD content below.

 

 

 

 

 

 

 

 

 

Speakers settings

Setting

Option

What it means

Speaker Distance

Specify the distance of your speakers from your listening

 

 

position (see Speaker Distance on page 30).

 

 

 

28

En

Loading...
+ 65 hidden pages