Size:
13.06 Mb
Download

HTZ180DVD

DVD/CD Receiver | DVD/CDġ

XV-DV180

Speaker System |ġ

S-DV180

HTZ181DVD

DVD/CD Receiver | DVD/CDġ

XV-DV181

Speaker System |ġ

S-DV585

HTZ280DVD

DVD/CD Receiver | DVD/CDġ

XV-DV282

Speaker System |ġ

S-DV280T / S-DV5SW

HTZ280DVD-AP

DVD/CD Receiver | DVD/CDġ

XV-DV282AP

Speaker System |ġ

S-DV280T / S-DV5SW

HTZ282DVD

DVD/CD Receiver | DVD/CDġ

XV-DV282

Speaker System |ġ

S-DV282T / S-DV5SW

HTZ282DVD-AP

DVD/CD Receiver | DVD/CDġ

XV-DV282AP

Speaker System |ġ

S-DV282T / S-DV5SW

Operating Instructions

D3-4-2-2-2a_A_En
D3-4-2-1-7a_A_En
#
D3-4-2-1-7b_A_En
!

IMPORTANT

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

CAUTION:

TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

D3-4-2-1-1_A1_En

&$( # !' & !"' * ' %#%"" " #% ) !' % "% & "-% " !"' # !, "!' ! % * '$( ! % ' &$( # !' &( & ) & "% "* % #"' "% +#"& ' '" % ## ! & ! % ! "% " &'(%

+$!) $ ) + ! ! %$, ' (*%%!- '($' # )$ $*#)'- $' ' $# (*' ) ) ) %$, ' (*%%!- +$!) $ ) ' , ' ) ( *# ) , !! *( " )( ) ' &* ' +$!) $' ,' )) # $# ) ' ' % # !

WARNING

To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the equipment.

VENTILATION CAUTION

When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 10 cm at top, 10 cm at rear, and 10 cm at each side).

WARNING

Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the equipment on thick carpet or a bed.

CAUTION

The STANDBY/ON switch on this unit will not completely shut off all power from the AC outlet. Since the power cord serves as the main disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power. Therefore, make sure the unit has been installed so that the power cord can be easily unplugged from the AC outlet in case of an accident. To avoid fire hazard, the power cord should also be unplugged from the AC outlet when left unused for a long period of time (for example, when on vacation).

S002*_En

CAUTION

This product is a class 1 laser product, but this product contains a laser diode higher than Class 1. To ensure continued safety, do not remove any covers or attempt to gain access to the inside of the product. Refer all servicing to qualified personnel.

The following caution label appears on your unit. Location: top of the unit

CLASS 1

LASER PRODUCT

D3-4-2-1-8*_C_En

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause a fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest PIONEER authorized service center or your dealer for a replacement.

Operating Environment

Operating environment temperature and humidity: +5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH (cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light)

D3-4-2-1-7c*_A1_En

If the AC plug of this unit does not match the AC outlet you want to use, the plug must be removed and appropriate one fitted. Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. If connected to an AC outlet, the cut-off plug can cause severe electrical shock. Make sure it is properly disposed of after removal.

The equipment should be disconnected by removing the mains plug from the wall socket when left unused for a long period of time (for example, when on vacation).

D3-4-2-2-1a_A1_En

Thank you for buying this Pioneer product.

Please read through these operating instructions so that you will know how to operate your model properly. After you have finished reading the instructions, put them in a safe place for future reference.

Contents

01 Speaker Setup Guide

Home theater sound setup . . . . . . . . . . . . . . . 6 5 spot/4 spot speaker layout . . . . . . . . . . . . . 6

3 spot/2 spot speaker layout . . . . . . . . . . . . . 6 Preparing the speakers. . . . . . . . . . . . . . . . . . 6

Preparation common to all models . . . . . . . 6 Preparation for the HTZ280DVD/

HTZ280DVD-AP/HTZ282DVD/

HTZ282DVD-AP . . . . . . . . . . . . . . . . . . . . . . 6

Preparation only for the HTZ181DVD . . . . . . 7

Wall mounting the speakers . . . . . . . . . . . . . . 7

Before mounting . . . . . . . . . . . . . . . . . . . . . 7

Attaching the brackets only for the HTZ180/ 181DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Additional notes on speaker placement . . . . . 8

02 Connecting up

Basic connections . . . . . . . . . . . . . . . . . . . . . 9

03 Controls and displays

Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Remote control . . . . . . . . . . . . . . . . . . . . . . . 14

Putting the batteries in the remote

control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Using the remote control . . . . . . . . . . . . . . 16

04 Getting started

Setting Speaker Layout . . . . . . . . . . . . . . . . . 17 Setting the channel levels . . . . . . . . . . . . . 17

Using the on-screen displays . . . . . . . . . . . . 18

Playing discs . . . . . . . . . . . . . . . . . . . . . . . . 18

Basic playback controls . . . . . . . . . . . . . . . 19 Resume and Last Memory . . . . . . . . . . . . . 19 DVD-Video disc menus. . . . . . . . . . . . . . . . 19

Video CD/Super VCD PBC menus . . . . . . . 19

Listening to the radio . . . . . . . . . . . . . . . . . . 20

Improving poor FM reception . . . . . . . . . . . 20

Reducing AM reception noise . . . . . . . . . . 20

Memorizing stations. . . . . . . . . . . . . . . . . . 20

Listening to station presets . . . . . . . . . . . . 21

Listening to other sources . . . . . . . . . . . . . . 21 Setting the sleep timer . . . . . . . . . . . . . . . . . 21

05 Listening to your system

Selecting Listening mode . . . . . . . . . . . . . . . 22

Auto listening mode . . . . . . . . . . . . . . . . . . . 22

Listening in surround sound . . . . . . . . . . . . . 22

Using Front Surround . . . . . . . . . . . . . . . . . . 23 Listening in stereo. . . . . . . . . . . . . . . . . . . . . 23

Listening with headphones . . . . . . . . . . . . . . 23

Adjusting the bass and treble . . . . . . . . . . . . 23

Using the SFC modes . . . . . . . . . . . . . . . . . . 23

Boosting the bass level . . . . . . . . . . . . . . . . . 24 Using the MP3 Expander. . . . . . . . . . . . . . . . 24

Using the Voice Enhancer mode . . . . . . . . . . 24 Effective Sound (for optimum sound) . . . . . . 24

06 Disc playback features

Scanning discs . . . . . . . . . . . . . . . . . . . . . . . 25

Playing in slow motion . . . . . . . . . . . . . . . . . 25

Frame advance/frame reverse . . . . . . . . . . . . 25 Playing a JPEG slideshow . . . . . . . . . . . . . . . 25

Browsing DVD or Video CD/Super VCD discs with the Disc Navigator . . . . . . . . . . . . . . . . . 26

Browsing Windows MediaTM Audio (WMA), MP3, MPEG-4 AAC, DivX video/WMV and

JPEG files with the Disc Navigator . . . . . . . . 27

Using Playlists. . . . . . . . . . . . . . . . . . . . . . . . 27

Programming playlists . . . . . . . . . . . . . . . . 27 Listening to playlists . . . . . . . . . . . . . . . . . . 28

Clearing files from a playlist . . . . . . . . . . . . 28 Looping a section of a disc . . . . . . . . . . . . . . 28

Using repeat play . . . . . . . . . . . . . . . . . . . . . 28 Using random play . . . . . . . . . . . . . . . . . . . . 28

Creating a program list . . . . . . . . . . . . . . . . . 29

Other functions available from the program menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Searching a disc . . . . . . . . . . . . . . . . . . . . . . 29 Switching subtitles . . . . . . . . . . . . . . . . . . . . 30

Switching language/audio channels . . . . . . . 30

Zooming the screen . . . . . . . . . . . . . . . . . . . 30

Switching camera angles . . . . . . . . . . . . . . . 30 Displaying disc information. . . . . . . . . . . . . . 30

4

En

07 USB playback and Recording

Using the USB interface . . . . . . . . . . . . . . . . 31

Recording the tracks of a music CD on

a USB device. . . . . . . . . . . . . . . . . . . . . . . . . 31

Recording all the tracks . . . . . . . . . . . . . . . 31 Recording specific tracks . . . . . . . . . . . . . . 32

08 Singing karaoke

Singing karaoke . . . . . . . . . . . . . . . . . . . . . . 33

Changing the vocal mix . . . . . . . . . . . . . . . 33 Changing the backing track . . . . . . . . . . . . 33

09 Audio Settings and Video Adjust

menus

Audio Settings menu. . . . . . . . . . . . . . . . . . . 34 Audio DRC . . . . . . . . . . . . . . . . . . . . . . . . . 34 Video Adjust menu . . . . . . . . . . . . . . . . . . . . 34

10 Initial Settings menu

Using the Initial Settings menu . . . . . . . . . . . 35

Video Output settings . . . . . . . . . . . . . . . . . . 35 Language settings. . . . . . . . . . . . . . . . . . . . . 36 Display settings. . . . . . . . . . . . . . . . . . . . . . . 37 Options settings . . . . . . . . . . . . . . . . . . . . . . 37 Speakers settings . . . . . . . . . . . . . . . . . . . . . 37

Parental Lock . . . . . . . . . . . . . . . . . . . . . . . 37

About DivX® VOD content . . . . . . . . . . . . . 38

Speaker Distance . . . . . . . . . . . . . . . . . . . . 39

11 Other connections

Connecting auxiliary audio components . . . . 40

Connecting using the component video

output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

About progressive scan video . . . . . . . . . . . 41 Connecting using HDMI . . . . . . . . . . . . . . . . 41 Switching the HDMI audio setting . . . . . . . 41

Resetting the HDMI connection . . . . . . . . . 42

About HDMI . . . . . . . . . . . . . . . . . . . . . . . . 42

Connecting external antennas. . . . . . . . . . . . 42

Bluetooth® ADAPTER for Wireless Enjoyment of Music . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Wireless music play . . . . . . . . . . . . . . . . . . 42

Remote control operation . . . . . . . . . . . . . . 43

Connecting Optional Bluetooth

ADAPTER . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Pairing Bluetooth ADAPTER and Bluetooth wireless technology device . . . . . . . . . . . . . 43 Listening to Music Contents of Bluetooth

wireless technology device with

Your System . . . . . . . . . . . . . . . . . . . . . . . . 44 Clearing Pairing . . . . . . . . . . . . . . . . . . . . . 44

12 KURO LINK

Making the KURO LINK connections. . . . . . . 45

KURO LINK Setup . . . . . . . . . . . . . . . . . . . . . 45

Setting the KURO LINK mode . . . . . . . . . . . 45 Before using synchronization . . . . . . . . . . . . 46 Synchronized amp mode . . . . . . . . . . . . . . . . 46 Synchronized amp mode operations . . . . . . 46 Canceling synchronized amp mode . . . . . . 46

13 Additional information

Disc/content format playback

compatibility . . . . . . . . . . . . . . . . . . . . . . . . . 47

Disc compatibility table. . . . . . . . . . . . . . . . 47

About DVD+R/DVD+RW compatibility. . . . 48

About DivX . . . . . . . . . . . . . . . . . . . . . . . . . 48 About WMV. . . . . . . . . . . . . . . . . . . . . . . . . 49 About MPEG-4 AAC. . . . . . . . . . . . . . . . . . . 49 About WMA . . . . . . . . . . . . . . . . . . . . . . . . 49

Using and taking care of discs. . . . . . . . . . . . 49

DVD Video regions . . . . . . . . . . . . . . . . . . . 50

Installation and maintenance . . . . . . . . . . . . 50

Hints on installation . . . . . . . . . . . . . . . . . . 50

Cleaning the pickup lens. . . . . . . . . . . . . . . 50

Problems with condensation. . . . . . . . . . . . 50 Moving the system unit . . . . . . . . . . . . . . . . 50

Screen sizes and disc formats . . . . . . . . . . . . 51

Widescreen TV users. . . . . . . . . . . . . . . . . . 51 Standard TV users . . . . . . . . . . . . . . . . . . . . 51 TV system setting. . . . . . . . . . . . . . . . . . . . . . 51

Frequency step setting. . . . . . . . . . . . . . . . . . 52

Dimming the Display . . . . . . . . . . . . . . . . . . . 52 Setting the Key Lock . . . . . . . . . . . . . . . . . . . 52 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . 53 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

DVD/CD/Video CD player. . . . . . . . . . . . . . . 54

Tuner. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 USB connection . . . . . . . . . . . . . . . . . . . . . 55 HDMI connection . . . . . . . . . . . . . . . . . . . . 55

Bluetooth connection . . . . . . . . . . . . . . . . . 56

Error Messages . . . . . . . . . . . . . . . . . . . . . . 56 Resetting the system . . . . . . . . . . . . . . . . . . . 57

Using the language code list . . . . . . . . . . . . . 57

Language code list. . . . . . . . . . . . . . . . . . . . . 58

Country/Area code list . . . . . . . . . . . . . . . . . . 58

Specifications . . . . . . . . . . . . . . . . . . . . . . . . 59

Neerland Italianods Françai s Deut sc h Engli

pañolE s

5

En

01 Speaker Setup Guide

Chapter 1

Speaker Setup Guide

Home theater sound setup

CAUTION

Depending on the size and characteristics of your room, you can place your speakers in one of two ways using this system. For the speaker configuration, see the Setup Guide.

5 spot/4 spot speaker layout

This is a standard multichannel surround sound speaker setup for optimal 5.1 channel home theater sound.

3 spot/2 spot speaker layout

This setup is ideal when rear surround speaker placement isn’t possible or you want to avoid running long speaker cables in your listening area.

Preparing the speakers

Preparation common to all models

Attaching non-skid pads

• Attach the smaller non-skid pads to the base of each of the speakers. The four large non-skid pads are for the subwoofer.

Use the supplied adhesive to attach 3 or 4 pads to the base (flat surface) of each speaker.

Preparation for the HTZ280DVD/ HTZ280DVD-AP/HTZ282DVD/ HTZ282DVD-AP

The layouts of the 5-spot speaker and 3-spot speaker are the same:

Assembling the speaker stands

• Attach the speaker stand bases to the stems using the screws provided.

Once you have aligned the stem and base, secure with the small screws at the points see the Setup Guide. Note that the speaker should face in the direction of the base of the isosceles triangle.

6

Be careful not to tighten screws excessively.

If excessive force is used to tighten screws, the threads of screw and/or nut may be damaged. Use a middle-sized manual screwdriver during assembly.

Do not use power screwdrivers or oversized screwdrivers that may exert excessive force on the screws and nuts.

Confirm that no foreign matter is stuck to the stand base or the tall speaker during assembly.

If the unit is assembled with foreign matter stuck between the stand base and the tall speaker the unit may not be assembled securely, resulting in tipping or falling.

Do not stand on the speaker stand base of the tall speaker to push or swing the speaker. The speaker may fall and break, or someone may be injured. Pay special attention to children.

Securing your front and surround speakers

• Secure each of the front and surround speakers using the plastic catch provided.

Screw two supporting hooks into the wall behind the speaker. Pass a thick cord around the hooks and through the plastic catch so that the speaker is stabilized (make sure to test that it supports the weight of the speaker). After installing, make sure the speaker is securely fixed.

Sufficiently thick cord

Plastic catch

En

Speaker Setup Guide

01

CAUTION

The plastic catch is not a mounting fixture, and the speaker should not be hung directly from the wall using this catch. Always use a cord when stabilizing the speaker.

Pioneer disclaims all responsibility for any losses or damage resulting from improper assembly, installation, insufficient strength of the installation materials, misuse, or natural disasters.

When placing this unit, ensure that it is firmly secured and avoid areas where it may be likely to fall and cause injury in the event of a natural disaster (such as an earthquake).

Preparation only for the HTZ181DVD

Stack the speakers and fix the brackets

Each speaker is provided with a color-coded indicator on the model label on the rear side to assist identification. Refer to the color indicators and install the speakers correctly. As shown in the illustration, stack the

speakers.1 Align the bracket with the respective upper and lower screw holes as shown in each figure below and fasten the screws securely.

4 spot/3 spot speaker layout:

4 spot:

 

 

3 spot:

 

 

Left

Right

 

Left

 

Right

Green

Center speaker

Green

 

Blue

 

Surround

Gray

 

 

speaker

 

 

 

 

 

 

 

 

 

White

Front speaker

Red

 

White

Front speaker

Red

 

 

 

 

 

 

 

 

 

 

Model label

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Color indicator

Bracket

Front speaker

Screw

2 spot speaker layout:

 

Left

 

Right

Model label

Blue

Surround speaker

Gray

 

 

 

 

 

Green

Center speaker

Green

 

 

 

 

Color indicator

White

Front speaker

Red

 

 

 

 

Bracket

Surround

speaker

 

 

Center

 

speaker

Screw

 

Front speaker

CAUTION

Do not attempt to carry the speakers when they are connected with the bracket. Doing so may cause damage to the bracket or worsen damage to the bracket and speakers in the event they are dropped.

Wall mounting the speakers

For the HTZ180DVD, the front and surround speaker have mounting brackets. For the HTZ181DVD, the front, center and surround speaker have mounting brackets. For the HTZ280DVD/280DVD-AP, the center and surround speaker have mounting holes. For the HTZ282DVD/HTZ282DVD-AP, only the center speaker has a mounting hole.

Before mounting

Remember that the speaker system is heavy and that its weight could cause the screws to work loose, or the wall material to fail to support it, resulting in the speaker

Engli

sc h

Neerland Italianods Françai s Deut

pañolE s

Note

1 When using the Front Surround mode, do not stack the surround speakers, but place them beside the front speaker and face

7

them about 60 degrees outward from the front speaker to obtain the best sound effect.

En

01 Speaker Setup Guide

falling. Make sure that the wall you intend to mount the speakers on is strong enough to support them. Do not mount on plywood or soft surface walls.

Mounting screws are not supplied. Use screws suitable for the wall material and support the weight of the speaker.

CAUTION

If you are unsure of the qualities and strength of the wall, consult a professional for advice.

Pioneer is not responsible for any accidents or damage that result from improper installation.

5 mm

10 mm

Mounting screw (not supplied)

5 mm to 7 mm

Attaching the brackets only for the HTZ180/181DVD

Make sure to tighten the supplied screw as securely as possible when attaching the bracket to the back of the speaker.

Please do not attach the brackets to the center speaker.

Bracket screw (supplied)

Additional notes on speaker placement

 

• Install the main front left and right

8

speakers at an equal distance from the TV.

• When using the 5 spot speaker layout, install the surround speakers slightly

above ear level for optimum effect.

Precautions:

When installing the center speaker on top of the TV, be sure to secure it with tape or some other suitable means. Otherwise, the speaker may fall from the TV due to external shocks such as earthquakes, endangering those nearby or damaging the speaker.

Make sure that all the bare speaker wire is twisted together and inserted fully into the speaker terminal. If any of the bare speaker wire touches the back panel it may cause the power to cut off as a safety measure.

The front, center and surround speakers supplied with this system are magnetically shielded. However, depending on the installation location, color distortion may occur if the speaker is installed extremely close to the screen of a television set. If this case happens, turn the power switch of the television set OFF, and turn it ON after

15 min. to 30 min. If the problem persists, place the speaker system away from the television set.

The subwoofer is not magnetically shielded and so should not be placed near a TV or monitor. Magnetic storage media (such as floppy discs and tape or video cassettes) should also not be kept close to the subwoofer.

Do not attach the center speaker (only of the HTZ180DVD) the front (of the HTZ280/ 282DVD)/surround speaker (only of the HTZ282DVD) and subwoofer to a wall or ceiling. They may fall off and cause injury.

Do not place the surround speaker on the top of the front speaker, as it may injure someone in the event that it falls (only for the HTZ280DVD).

En

Connecting up

02

Chapter 2

Connecting up

Basic connections

For the best surround sound, setup your speakers as below. The front left and right speaker should be about 1.8 m to 2.7 m apart.

The speakers in the illustration below are the HTZ180DVD.

 

 

 

 

 

COMPONENT

PR

LINE 1

R

FRONT

L

CENTER

VIDEO

 

L

 

 

 

 

VIDEO(TV)

PB

AC IN

R

 

 

Y

 

R

 

L

SUB

 

SURROUND

WOOFER

ANALOG AUDIO IN SPEAKERS (4 Ω ) VIDEO OUT

 

Front right

 

(Red)

Front left

Center

(White)

(Green)

 

Subwoofer

 

(Purple)

Surround left

Surround right

(Blue)

(Grey)

 

Listening position

A

 

 

 

N

 

 

 

T

 

 

 

E

 

 

 

N

 

 

 

N

 

FM

 

A

AM LOOP

UNBAL 75

Ω

HDMI OUT

To video input

FM antenna

AM loop antenna

TV

Important

When connecting this system or changing connections, be sure to switch power off and disconnect the power cord from the wall socket.

After completing all connections, connect the power cords to the wall socket.

WARNING

Pioneer bears no responsibility for accidents resulting from faulty assembly or installation, insufficient mounting strength of walls, mounting fixtures (or other building fixtures), misuse or natural disasters.

1 Assemble the AM loop antenna.

fig. a

fig. b

fig. c

a.Bend the stand in the direction indicated by the arrow.

b.Clip the loop onto the stand.

c.If you want to fix to a wall or other surface, perform step b after first securing the stand with screws.

It is recommended that you determine the reception strength before securing the stand with the screws.

English

Español Nederlands Italiano Français Deutsch

9

En

02 Connecting up

2Connect the AM and FM antennas.1

a.Pull off the protective shields of both AM antenna wires. Connect one wire of the AM loop antenna to each AM antenna terminal.2

For each terminal, press down on the tab to open; insert the wire, then release to secure.

3 1

2

b.Push the FM antenna3 plug onto the center pin of the FM antenna socket.

3-1 Connect each speaker.

• Connect the wires to the speaker.

Color-coded wire (Connect to speaker)

Color-coded connector (Connect to rear panel)

Match the color-coded wire with the color indicator on the label, then insert the colorcoded wire into the red (+) side and the other wire into the black (–) side.

Black (–) Red (+)

Color-coded wire

HTZ180DVD only:

When you select the 3 spot speaker layout, follow steps a through c below to set up the speakers.

a. The base of each surround speaker fits into the circular groove on the top of the front speakers as shown.

Twist and pull off the protective shields on each wire.

Note

1 • Keep antenna cables away from the receiver and other cables.

If reception with the supplied antenna is poor, see Improving poor FM reception on page 20 or Connecting external antennas on page 42.

Do not attach any antenna other than the provided loop antenna, or an external antenna as described on page 42. 2 • Don’t let it come into contact with metal objects and avoid placing near computers, television sets or other electrical

appliances.

If radio reception is poor, you may be able improve it by re-inserting each antenna wire into the opposite terminal.

For best reception, do not untwist the AM loop antenna wires or wrap them around the loop antenna.

3 To ensure optimum reception, make sure the FM antenna is fully extended and not coiled or hanging at the rear of

the unit.

10

En

Connecting up

02

b. Secure the speaker wire.

After testing for the slack necessary to turn the speaker (see the following step), use the groove provided to secure the speaker wire.

c. Turn the speakers towards the closest wall, lining the arrows up for optimal Front Surround.

For Front Surround mode, turn each surround

speaker so that the arrow at the base is lined up with the (FRONT SURROUND) arrow on

the front speaker. For Extra Power mode, have all the speakers facing forward. See the

Listening to your system for more on using Front Surround and Extra Power modes.

CAUTION

To prevent accidents, make sure the surround speaker is placed securely on top of the front speaker.

Please don’t attach the speakers to the wall or speaker stands for 3 spot speaker layout.

HTZ181DVD only :

English

a. When connecting the center speakers,

 

connect the Y-cable dual end to the two

 

center speakers in the same way.

 

 

Deutsch

Y-cable

Français

 

To Main Unit

 

When you select a 4-spot, 3-spot or 2-spot

 

layout where the brackets are used for

 

assembling, also follow step b below.

Italiano

b. When connections are completed, secure

 

the speaker cables. Fix the cables to the

 

groove in the brackets.

 

 

Nederlands

3-2 Connect each speaker terminals on the

Español

receiver.

 

• Connect the other end to the color-coded speaker terminals on the rear of the receiver. Make sure to insert completely.

The small lug at the wire-end of the speaker plug should face up or down depending on whether it’s being plugged into one of the upper or lower speaker terminals. Please make sure to connect correctly.

Upper terminal

Lower terminal

11

En

02 Connecting up

CAUTION

These speaker terminals carry

HAZARDOUS LIVE voltage. To prevent the risk of electric shock when connecting or disconnecting the speaker cables, disconnect the power cord before touching any uninsulated parts.

Do not connect any speakers other than those supplied to this system.

Do not connect the supplied speakers to any amplifier other than the one supplied with this system. Connection to any other amplifier may result in malfunction or fire.

After connecting the plugs, pull lightly on the cables to make sure that the ends of the cables are securely connected to the terminals. Poor connections can create noise and interruptions on the sound.

If the cable’s wires happen to be pushed out of the terminals, allowing the wires to come into contact with each other, it places an excessive additional load on the amp. This may cause the amp to stop functioning, and may even damage the amp.

4Connect one end to a video input on your

TV.

Use the supplied video cable.

5Connect the other end to the video output of the receiver.

This unit is equipped with copy protection technology. Do not connect this unit to your TV via a VCR using AV cables, as the picture from this unit will not appear properly on your TV.

Connect the power cord to AC inlet on the receiver. Connect the power cord to a wall socket.

AC IN

To AC outlet

6 Connect the power cord.1

Note

1 • Do not use any power cord other than the one supplied with this system.

• Do not use the supplied power cord for any purpose other than connecting to this system.

12

En

Controls and displays

Chapter 3

Controls and displays

03

English

Front panel

1

2

3

4

5

6

STANDBY/ON

OPEN/CLOSE

FUNCTION

 

 

VOLUME

 

 

 

7

 

8

 

9

 

MAIN MIC SUB PHONES

USB

10 11 12

1STANDBY/ON (page 17, 32, 43, 50, 52 and 54)

2OPEN/CLOSE (page 18, 32 and 53)

3Function

6VOLUME +/– (page 19)

7Disc tray (page 18)

8Remote Sensor (page 15)

9Display

10USB interface (page 31)

11MIC input jacks (page 33)

12PHONES jack (page 23)

Display

1

2

3

4

 

5

 

6

 

PRGSVE SOUND

 

 

 

 

 

 

DTS

F.SURR.

 

 

RPT -1

 

 

2D

 

 

 

kHz PGM

 

2PL

 

 

 

MHz RDM

 

 

12 11

10

9

8

7

1 Decord indicators (page 22)

DTS lights during playback of a DTS source. 2PL II lights during 2Dolby Pro Logic II decoding and 2D lights during playback of Dolby Digital sources.

2 PRGSVE (page 41)

Lights when progressive scan video signal is given from the component video output terminal.

3 SOUND (page 23)

Lights when the SFC modes, the tone controls (treble, bass or bass boost), MP3 Expander mode, Voice Enhancer mode are active.

4 F.SURR. (page 23)

Lights when the Extra Power mode/Front surround mode is selected.

5 RPT and RPT-1 (page 28)

RPT lights during repeat play. RPT-1 lights during repeat one-track play.

6 PGM (page 27 and 29)

Lights during program or playlist playback.

7 Tuner indicators (page 20)

Lights when a broadcast is being received, Lights when a stereo FM broadcast is

being received, Lights when FM mono reception is selected.

8 RDM (page 28)

Lights during random play.

Español Nederlands Italiano Français Deutsch

13

En

03 Controls and displays

9 kHz/MHz (page 20)

Indicates the frequency unit shown in the character display (kHz for AM, MHz for FM).

10 Character display

Remote control

The illustration shows the HTZ280/282DVD-AP.

11 (page 21)

Lights when sleep timer is active.

12

Lights during playback.

 

STANDBY

 

TUNER

 

 

1

/ON

DVD/CD

(FM/AM)

OPEN/CLOSE

11

ADAPTERPORT

USB

LINE

PLAYLIST

2

 

 

 

 

1

 

 

1

2

3

2

12

 

USB REC

AUDIO

SUBTITLE

 

 

3

4

5

6

3

 

 

ANGLE

ZOOM

 

 

 

7

8

9

 

13

 

CLEAR

SLEEP

DISPLAY

MIC VOL

 

0

 

 

 

 

 

4

TOP MENU

TUNE

MENU

14

SETUP

 

 

 

5

 

 

 

 

PRESET

ENTER

PRESET

 

 

HOME

 

 

 

 

6

MENU

 

 

RETURN

15

AUTO/

TUNE

MP3 EXP/

 

 

7

STEREO

SURROUND

SOUND

V.ENH

 

 

 

 

 

 

8

 

 

 

 

 

 

TV CONTROL

 

CLASS

16

9

INPUT

CHANNEL

VOLUME

T.EDIT

MUTE

17

 

SHIFT

 

VOLUME

 

10

 

 

18

 

 

 

 

1STANDBY/ON (page 17, 32, 43, 50, 52 and 54)

2Function select buttons1

3Number buttons, CLEAR, DISPLAY, SLEEP and DVD controls

CLEAR

DISPLAY (page 30)

SHIFT+SLEEP (page 21)

SHIFT+USB REC (page 31)

SHIFT+AUDIO (page 30)

SHIFT+SUBTITLE (page 30)

Note

1 Only the HTZ280/282DVD-AP models are equipped with the adapter port.

14

En

Controls and displays

03

SHIFT+ANGLE (page 30)

SHIFT+ZOOM (page 30)

4TOP MENU (page 19 and 30)

SHIFT+SETUP (page 17, 20, 41, 43, 44, 45, 51, 52 and 57)

5SHIFT+KARAOKE (page 33) SHIFT+ECHO (page 33) SHIFT+ / SHIFT+ (page 33)

Cursor buttons ENTER

TUNE (page 20) PRESET (page 20)

6HOME MENU

7Sound controls

AUTO/STEREO (page 22 and 23) SURROUND (page 22 and 23) SOUND (page 23 and 24)

MP3 EXP/V.ENH (page 24)

8Playback controls (page 19 and 25)

9TV CONTROL buttons

These control Pioneer flat screen TVs.1

10SHIFT

11OPEN/CLOSE (page 18, 32 and 53)

12PLAYLIST buttons (page 27)

13MIC VOL +/– (page 33)

14MENU (page 19, 26 and 30)

15RETURN

16Tuner controls CLASS (page 21)

SHIFT+T.EDIT (page 20)

17MUTE

18VOLUME +/– (page 18)

Putting the batteries in the remote control

1Open the battery compartment cover on the back of the remote control.

2Insert two AA/R6 batteries into the battery compartment following the indications ( , ) inside the compartment.

3Close the cover.

CAUTION

Incorrect use of batteries can result in hazards such as leakage and bursting. Please observe the following:

Always insert batteries into the battery compartment correctly matching the positive and negative polarities, as shown by the display inside the compartment.

Never mix new and used batteries.

Batteries of the same size may have different voltages, depending on brand. Do not mix different brands of batteries.

When disposing of used batteries, please comply with governmental regulations or environmental public instruction’s rules that apply in your country or area.

Note

1 Hold down the number button 1 for over three seconds with the CLEAR pressed. If the TV refuses to respond, hold down the number button 2. After control is properly switched over, the power to the TV can be operated by directing the TV CONTROL

toward the TV and pressing it.

Español Nederlands Italiano Français Deutsch English

15

En

03Controls and displays

In order to prevent battery leakage, remove the batteries when not using the remote control for an extended period (one month or more). If leakage occurs, carefully wipe away any battery fluid inside the compartment, and replace the batteries with new ones.

Do not allow books or other objects to rest on top of the remote control, since the buttons may be depressed, causing faster exhaustion of the batteries.

Do not use or store batteries in direct sunlight or excessively hot places, such as inside a car or near a heater. This can cause batteries to leak, overheat, explode or catch fire. It can also reduce the life or performance of batteries.

Using the remote control

The remote control can be used within a range of about 7 meters from the remote sensor on the front panel, and within a 30 degree angle.

The remote control may not work if there is an obstacle between the remote control and the display unit, or if the remote control is not directed towards the remote sensor of the display unit at the correct angle.

The remote control may not work properly if strong light such as direct sunlight or fluorescent light is shining onto the unit’s remote sensor.

The remote control may not work properly when this unit is used near devices emitting infrared rays, or when remote controls of other devices which use infrared rays are used. Also, the use of this remote control may cause other devices to work improperly.

When the operating range of the remote becomes too short, replace the batteries.

16

En

Getting started

Chapter 4

Getting started

Setting Speaker Layout

Select the speaker layout for the speaker setting you arranged to your listening area environment.

First time you switch on the system, the following speaker layout setting appears. If you switch off the system without finishing this setting, the same appears again next time you switch on the system.

1Press STANDBY/ON and confirm

WELCOME is shown on the display.

2SELECT SPEAKER LAYOUT will run on the display for about 10 seconds.

3Use / to select appropriate speaker layout.

3 SPOT – This is the classic layout for the Front Surround mode. The two surround speakers are placed in front of the listening position.

2 SPOT (HTZ181DVD only) – This layout for the Front Surround mode is the same as the 3 spot speaker layout. The two center speakers are separated to the right and left sides, and neatly arranged around the TV.

4 Press ENTER to confirm.1

Setting the channel levels

Set the relative channel levels from your main listening position.2

1 Press SHIFT+SETUP.

There are two speaker layout modes – 5 spot speaker layout and 3 spot speaker layout.

See Setup Guide for more details about speaker layout and mode description.

5 SPOT – Optimal for 5.1 channel home theater sound by placing the two surround speakers in the rear of the listening position.

4 SPOT (HTZ181DVD only) – This is the standard layout for listening to the surround sound, which is similar to the 5 spot speaker layout. The two center speakers are separated to the right and left sides, and neatly arranged around the TV.

2Use / to select SOUNDSET, then press ENTER.

3Use / to select CH LEVEL, then press ENTER.

4Use / to select TESTTONE, then press ENTER.

The test tone is output in the following order (from the speakers active in the current listening mode):

L – Front left speaker

C – Center speaker

R – Front right speaker

SR – Surround right speaker

SL – Surround left speaker

SW – Subwoofer3

Note

1To change the setting, press SHIFT+SETUP, use / to select SYS SET, then use / to select LAYOUT to start setting procedure.

2• This is only available when DVD/CD is selected and playback is stopped. Also make sure headphones are unplugged.

To adjust the overall balance while listening to any sound source you want, press SHIFT+SETUP, use / to select SOUNDSET, then press ENTER. Use / to select CH LEVEL, then press ENTER. Use / to switch between channels, and

/ to adjust the channel levels. Press ENTER when you’re finished.

3 Since the subwoofer produces ultra-low frequencies its sound may seem quieter than it actually is.

04

Español Nederlands Italiano Français Deutsch English

17

En

04 Getting started

5Use the VOLUME +/– to adjust the volume to an appropriate level.1

6Use / to adjust the channel levels in turn.

You should hear the test tone at the same volume from each speaker when seated in the main listening position. The channel level range is ±10 dB.

7 When you’re done, press ENTER to exit test tone setup.

Using the on-screen displays

For ease of use, this system makes extensive use of graphical on-screen displays (OSDs).

All the screens are navigated in basically the same way, using , , , to change the highlighted item and pressing ENTER to select

it.2

Important

Throughout this manual, ‘Select’ means

use the cursor buttons to highlight an item on-screen, then press ENTER.

Button What it does

HOME Displays/exits the on-screen display.

MENU

Changes the highlighted menu item.

ENTER Selects the highlighted menu item.

RETURN Returns to the main menu without saving changes.

Tip

The button guide at the bottom of every OSD screen shows you which buttons you’ll need to use for that screen.

Playing discs

The basic playback controls for playing DVD, CD, Video CD/Super VCD, DivX video/WMV and WMA/MP3/MPEG-4 AAC discs are covered here. Further functions are detailed in chapter 6.

Important

Throughout this manual, the term ‘DVD’ means DVD-Video, DVD-R and DVD-RW.

1If the player isn’t already on, switch it on.

If you’re playing a disc with video, also turn on your TV and make sure that it is set to the correct video input.

2Press OPEN/CLOSE to load a disc.

Load a disc with the label side facing up, using the disc tray guide to align the disc (if you’re loading a double-sided DVD disc, load it with the side you want to play face down).

3Press (play) to start playback.

If you’re playing a DVD or Video CD/Super VCD, a menu may appear. See DVD-Video disc menus and Video CD/Super VCD PBC menus on page 19 to navigate these.

If you loaded a disc containing JPEGs, a slideshow will start. See Playing a JPEG slideshow on page 25 for more on this.

If a disc contains a mixture of DivX video/ WMV and other media file types (MP3, for

example), first select whether to play the DivX video/WMV files (DivX/WMV) or the other media file types (MP3/WMA/JPEG/ MPEG-4 AAC) from the on-screen display.

Note

1When the volume is set to 51 or more, TESTTONE cannot be selected and the channel level setting range is restricted. In addition, if the channel level range of any speaker is set to the + side, the maximum volume is also restricted.

2The screen saver will appear after five minutes of inactivity.

18

En

Getting started

04

Please see Disc/content format playback compatibility on page 47 if you want to play a DualDisc (DVD/CD hybrid disc).

4 Adjust the volume.

Use the VOLUME +/– control.

Basic playback controls

The following table shows the basic controls on

the remote for playing discs.1 You can find other playback features in chapter 6.

Button What it does

Starts/resumes normal playback.

If the display shows RESUME or

LAST MEM playback starts from the resume or last memory point (see

Resume and Last Memory below).

Pauses/unpauses a disc.

Resume and Last Memory

When you stop playback of a disc, RESUME shows in the display indicating that you can resume playback from that point.

With DVDs and Video CD/Super VCDs, even if

ejected, the play position is stored in memory.2

The next time you load the disc, the display shows LAST MEM and you can resume

playback.

If you want to clear the resume point, press(stop) while RESUME is displayed.

DVD-Video disc menus

Many DVD-Video discs contain menus from which you can select what you want to watch.

Sometimes DVD-Video menus are displayed automatically when you start playback; others

only appear when you press MENU or TOP MENU.

Stops playback or cancels the resume function (if the display shows RESUME).

Press to start fast reverse scanning.

Press to start fast forward scanning.

Skips to the start of the current track or chapter, then previous tracks/chapters.

Skips to the next track or chapter.

Numbers Use to enter a title/chapter/track number. Press ENTER to select.

If the disc is stopped, playback starts from the selected title (for DVD) or track (for CD/Video CD/Super VCD).

If the disc is playing, playback jumps to the start of the selected title (VR mode DVD-R/-RW), chapter (DVDVideo) or track (CD/Video CD/Super VCD).

Button

What it does

 

 

TOP MENU Displays the ‘top menu’ of a DVD disc — this varies with the disc.

MENU Displays a DVD disc menu — this varies with the disc and may be the same as the ‘top menu’.

Moves the cursor around the screen.

ENTER Selects the current menu option.

RETURN Returns to the previously displayed menu screen.

Numbers Highlights a numbered menu

option (some discs only). Press ENTER to select.

Video CD/Super VCD PBC menus

Some Video CD/Super VCDs have menus from which you can choose what you want to watch. These are PBC (Playback control) menus.

Note

1You may find with some DVD discs that some playback controls don’t work in certain parts of the disc.

2•The Resume and the Last Memory functions may not work with some discs.

• For DVD-Video discs (except VR mode DVD-R/-RW), the player stores the play position of the last five discs.

Español Nederlands Italiano Français Deutsch English

19

En

04 Getting started

You can play a PBC Video CD/Super VCD without having to navigate the PBC menu by starting playback using a number button to select a track, rather than the (play) button.

Button

What it does

RETURN

Displays the PBC menu.

 

 

Numbers

Selects numbered menu options.

 

Press ENTER to select.

Displays the previous menu page (if there is one).

Displays the next menu page (if there is one).

1Tune to an FM radio station then press SHIFT+SETUP.

2Use /to choose TUNERSET then press

ENTER.

3Use /to choose FM MODE then press

ENTER.

4Use / to select FM MONO then press

ENTER.

The mono indicator ( ) lights when the tuner is in mono reception mode.

Select FM AUTO above to switch back to autostereo mode (the stereo indicator () lights when receiving a stereo broadcast).

Listening to the radio

The tuner can receive both FM and AM broadcasts, and lets you memorize your favorite stations so you don’t have to manually tune in every time you want to listen.

1 Press TUNER to switch to the tuner, then press repeatedly to select the AM or FM band.

The display shows the band and frequency.

2 Tune to a frequency.

There are three tuning modes — manual, auto, and high-speed:

Manual tuning: Press TUNE repeatedly to change the displayed frequency.

Auto tuning: Press and hold TUNE until the frequency display starts to move, then release. The tuner will stop on the next station it finds. Repeat to keep searching.

High-speed tuning: Press and hold

TUNE until the frequency display starts to move rapidly. Keep the button held down until you reach the frequency you want. If necessary, fine tune the frequency using the manual tuning method.

Improving poor FM reception

If you’re listening to an FM station in stereo but the reception is weak, you can improve the sound quality by switching to mono.

20

Reducing AM reception noise

If AM reception seems particularly poor, or the AM radio station you’re listening to seems noisy, try using the Noise Cut feature for better sound quality.

1Tune to an AM radio station then press SHIFT+SETUP.

2Use / to choose TUNERSET then press ENTER.

3Use /to choose NOISECUT then press

ENTER.

4Use / to select the noise cut mode then press ENTER.

Select an effect level between 1 or 2.

Memorizing stations

This system can memorize up to 30 stations, stored in three banks, or classes (A, B and C) of 10 stations each.

1 Tune to an AM or FM radio station.

For the FM band, select mono or auto-stereo reception as necessary. This setting is saved along with the preset.

2Press SHIFT+T.EDIT.

3Press CLASS to select one of the three classes, then use the PRESET buttons to select the station preset you want.

You can also use the number buttons to select a preset.

En

Getting started

4 Press ENTER.

After pressing ENTER, the preset class and number stop blinking and the system memorize station.

Listening to station presets

You will need to have some presets stored to do this.

1Make sure the TUNER function is selected.

2Press CLASS to select the class in which the channel is stored. Press repeatedly to cycle through classes A, B and C.

3Use the PRESET buttons to select a station preset.

You can also use the number buttons to do this.

Listening to other sources

You can connect auxiliary sources (TV, satellite receiver, etc.) to this unit for playback through the speaker system. See Connecting auxiliary audio components on page 40 for more on this.

To connect a USB device to the USB terminal, see USB playback and Recording on page 31.

HTZ280/282DVD-AP only: Bluetooth ADAPTER is selectable when it is plugged and detected. See Bluetooth® ADAPTER for Wireless Enjoyment of Music on page 42 for more on this.

1Make sure that the external source (TV, satellite receiver, etc.) is switched on.

2Press LINE to select the source.

3If necessary, start playback of the source.

Setting the sleep timer

The sleep timer switches off the system after about an hour so you can fall asleep without

worrying about it.1

• Press SHIFT+SLEEP repeatedly to select an option then press ENTER.

Choose between the following options:

SLP ON – Switches off after about an hour. The indicator lights.

SLP OFF – Cancels the sleep timer.

After selecting SLP ON, you can press SHIFT+SLEEP again to check how much time

is left. Each line indicates approximately 12 minutes (remaining):

S L P - - - --

04

Español Nederlands Italiano Français Deutsch English

Note

1 The display dims when the sleep timer is set.

21

En

05 Listening to your system

Chapter 5

Listening to your system

Important

This unit’s audio function may be restricted depending on the sound source, HDMI audio setting (page 41) or karaoke mode with the microphone plugged in (page 33). In this event, the menus may not appear, or a message may be displayed instead (page 56).

Auto listening mode

The Auto listening mode is the simplest way to listen to any source as it was mastered: the output from the speakers mirrors the channels in the source material.

• Press AUTO/STEREO to select the AUTO listening mode.1

The listening mode is automatically allotted according to the source material as shown in

Selecting Listening mode

Various listening modes are available for enjoyment of diverse sound effects and for sound field correction according to your preference. Depending on the speaker layout you have chosen in the Home theater sound setup on page 6, the listening mode you can set differs. Read the following and proceed with each setting.

5 spot/4 spot speaker layout

When you have chosen 5 spot speaker layout, select one listening mode from the surround sound mode. See Listening in surround sound below.

3 spot/2 spot speaker layout

When you have chosen 3 spot speaker layout which places the surround speakers in front of you, select one listening mode from the front surround mode. See Using Front Surround on page 23.

the table below.

source

5 SPOT

3 SPOT

4 SPOT

2 SPOT

 

 

 

 

two-ch

STEREO

STEREO

multi-ch

STANDARD

F.SURR

 

 

 

Listening in surround sound

When you set up the system for 5 spot/4 spot speaker layout, the surround sound mode is available.

You can listen to stereo or multichannel

sources in surround sound.2 Surround sound is generated from stereo sources using one of the Dolby Pro Logic decoding modes.

• Press SURROUND repeatedly to select a listening mode.1

The choices that appear in the display will vary according to the type of source that’s playing.

STANDARD – Standard decoding mode (This mode can be selected only when the source is multi channel)

MOVIE (Dolby Pro Logic II Movie) – Pro Logic II 5.1 channel surround sound, especially suited to movie sources (use with any two-channel source)

Note

1If the source is Dolby Digital or DTS, the corresponding indicator lights in the front panel display.

2Note that the input source must be switched to DVD/CD or USB for multichannel playback.

22

En

Listening to your system

MUSIC (Dolby Pro Logic II Music) – Pro Logic II 5.1 channel surround sound, especially suited to music sources (use with any two-channel source)

DOLBY PL (Dolby Pro Logic) – 4.1 channel surround sound (use with any two-channel source)

Using Front Surround

The Front Surround mode and Extra Power mode are effective when DVD/CD or USB is

selected as the input source and you are using 3 spot (/2 spot only for HTZ181DVD) speaker layout as described in Home theater sound setup on page 6.

• Press SURROUND repeatedly to select a front surround mode.

F.SURR – Use to provide rich surround sound effect.

EXTRAPWR – Outputs stereo sound (in the case of multi-channel sources, downmixed stereo sound) from the surround speakers for powerful stereo effect.

For HTZ180DVD

For Front Surround

For Extra Power

mode

mode

Listening in stereo

You can listen to any source — stereo or multichannel — in stereo. When playing a multichannel source, all channels are downmixed to the front left/right speakers and the subwoofer.

• Press AUTO/STEREO repeatedly until STEREO shows in the display.

Listening with headphones

When headphones are connected, the STEREO playback mode starts. The listening

mode cannot be changed.1

Adjusting the bass and treble

Use the bass and treble controls to adjust the overall tone.

1Press SOUND.

2Use / to select BASS/TRE then press

ENTER.

3Use / to select BASS or TREBLE.

4Use / to adjust the sound then press

ENTER to confirm.

Bass and Treble can be adjusted from –6dB to +6dB.

Using the SFC modes

The SFC (Sound Field Control) modes can be used with any multichannel or stereo source for a variety of additional surround sound effects.

For HTZ181DVD

 

1

Press SOUND.

For Front Surround

For Extra Power

 

 

mode

mode

2

Use / to select SFC MODE then press

Surround Speaker

 

ENTER.

3 Press / then ENTER to select an SFC

Sound mode.

Select between OFF, LIVE, HALL, POP, ROCK,

DRAMA or ACTION.

This illustration is 3 spot layout.

Note

1 When you disconnect the headphones, the system reverts to the previous surround setting mode.

05

Español Nederlands Italiano Français Deutsch English

23

En

05 Listening to your system

Boosting the bass level

There are two bass modes you can use to enhance the bass in a source.

1Press SOUND.

2Use /to select BASSMODE then press

ENTER.

3Use / to adjust the sound then press

ENTER to confirm.

Select between OFF, MUSIC or CINEMA.

Using the MP3 Expander

Reproduce the comfortable sound for compressed music (MP3, WMA, MPEG-4 AAC).

• Press MP3 EXP/V.ENH repeatedly to select MP3 EXP.1

Using the Voice Enhancer mode

This mode is used for easy listening to the spoken lines of the movies or dialogs.

• Press MP3 EXP/V.ENH repeatedly to select VOICE E.2

Effective Sound (for optimum sound)

With the uniquely shaped high-quality speakers supplied with this unit, the Effective Sound mode enables the following Pioneer exclusive audio technologies designed to maximize the real experience of sound originally inherent in movies and music.

Turn on the Effective Sound mode under normal circumstances to maximize the

capabilities of this unit.3

Dynamic Range Compression

Resuscitates detailed sound susceptible to ambient noise to create an acoustic environment where you feel as if you are right in the action.

Frequency Characteristic Correction

Realizes the playback characteristic optimized for long hours of listening in addition to the added features of the supplied speaker units.

1Press SHIFT+SETUP and use / to select SOUNDSET, then press ENTER.

2Use / to select S.FIELD then press

ENTER.

3Use / to adjust the setting then press

ENTER to confirm.

EFFECT (Effective Sound) – Plays the sound with the characteristics optimized for the included speakers.

DIRECT (Direct Sound) – Turns off the Effective Sound mode.

Note

1When turned on, the SFC mode will be turned off.

2• When turned on, the SFC mode will be turned off.

Not applicable to the HTZ180/181DVD model - Effective only for the center channel when a multi channel source is played.

3The Sound Field will not affect the headphone outputs.

24

En

Disc playback features

Chapter 6

Disc playback features

Important

Many of the functions covered in this chapter apply to DVD discs, Video CDs/ Super VCDs, CDs, DivX video/WMV and WMA/MP3/MPEG-4 AAC/JPEG discs, although the exact operation of some varies slightly with the kind of disc loaded.

Some DVDs restrict the use of some functions (random or repeat, for example) in some or all parts of the disc. This is not a malfunction.

When playing Video CD/Super VCDs, some of the functions are not available during PBC playback. If you want to use them, start the disc playing using a number button to select a track.

1During playback, press (pause).

2Press and hold /or /until slow motion playback starts.

Press repeatedly to change the slow motion speed (shown on-screen).

• To resume playback, press (play).2

Frame advance/frame reverse

You can advance or back up DVD discs frame- by-frame. With Video CD/Super VCDs and DivX video/WMV you can only use frame advance.

1During playback, press (pause).

2Press / or / to reverse or advance a frame at a time.

To resume playback, press (play).2

Scanning discs

Playing a JPEG slideshow

You can fast-scan discs forward or backward at

various different speeds.1

• During playback, press or to start scanning.

Press repeatedly to increase the scanning speed (shown on-screen).

• To resume playback, press (play).2

Playing in slow motion

You can play DVDs, Video CD/Super VCDs and DivX video/WMV at four different forward slow motion speeds. DVD discs can also be played in reverse slow motion.

After loading a disc containing JPEG pictures, press to start a slideshow from the first

folder/picture on the disc.3 The player displays the pictures in each folder in alphabetical order.

If the disc contains WMA/MP3/MPEG-4 AAC files, playback of the slideshow and audio files repeats. During audio playback, you can still use the skip ( / ), scan ( / ) and pause ( ) functions.

Pictures are automatically adjusted so that they fill as much of the screen as possible.

Note

1Only one speed is available for DivX video/WMV discs.

2• Depending on the disc, normal playback may automatically resume when a new chapter is reached on a DVD disc.

For Video CDs/Super VCDs in PBC mode and WMA/MP3/MPEG-4 AAC tracks (in Scan mode only) normal playback resumes when you reach the beginning or the end of track.

3• The time it takes for the player to load a file increases with large file sizes.

Discs can contain up to 299 folders and up to 648 folders and files combined.

06

Español Nederlands Italiano Français Deutsch English

25

En

06 Disc playback features

While the slideshow is running:

The options available depend on the kind of

 

 

disc loaded and whether the disc is playing or

Button

What it does

not, but include:

 

 

Pauses the slideshow (or audio); • Title – Titles from a DVD-Video disc.

press again to restart.

Jumps to the previous picture (or audio file with audio playback).

Jumps to the next picture (or audio file with audio playback).

/ / / Pauses the slideshow and rotates/flips the displayed picture (Press (play) to restart slideshow).

SHIFT+ZOOM Pauses the slideshow and zooms the picture. Press again to toggle between 1x, 2x and 4x zoom (Press (play) to restart slideshow).

MENU Displays the Disc Navigator

screen (see below).

Chapter – Chapters from the current title of a DVD-Video disc.

Track – Tracks from a Video CD/Super VCD disc.

Time – Thumbnails from a Video CD/Super VCD disc at 10 minute intervals.

Original: Title – Original titles from a VR mode DVD-R/-RW disc.

Playlist: Title – Playlist titles from a VR mode DVD-R/-RW disc.

Original: Time – Thumbnails from the Original content at 10 minute intervals.

Playlist: Time – Thumbnails from the Playlist at 10 minute intervals.

The screen shows up to six moving thumbnail images displayed one after another. To display the previous/next six thumbnails, press /

.

Browsing DVD or Video CD/ Super VCD discs with the Disc Navigator

Use the Disc Navigator to browse through the contents of a DVD or Video CD/Super VCD disc to find the part you want to play.

1 During playback, press HOME MENU and select ‘Disc Navigator’ from the onscreen menu.

Disc Navigator

2 Select a view option.

Disc Navigator

Title

Chapter

3 Select the thumbnail image for what you want to play.

01

02

03

04

05

06

Disc Navigator: Title 0149: --

You can use either / / / and ENTER to select a thumbnail, or the number buttons.

To select using the number buttons, enter a two-digit number then press ENTER.

26

En

Disc playback features

Browsing Windows MediaTM Audio (WMA), MP3, MPEG-4 AAC, DivX video/WMV and JPEG files with the Disc Navigator

Use the Disc Navigator to find a particular file or folder by filename.

1 Press HOME MENU and select ‘Disc Navigator’ from the on-screen menu.

00:00/ 00:00

0kbps

Folder1

Folder2

Folder3

Folder4

2 Use / / / and ENTER to navigate.

Use /to move up and down the folder/file list.

Use to return to the parent folder.1

Use ENTER or to open a highlighted folder.

When a JPEG file is highlighted, a thumbnail image is displayed on the right.

00:00/ 00:00

0kbps

Folder2

File1

File2

File3

File4

File5

3 To play the highlighted track or DivX video/WMV file or display the highlighted JPEG file, press ENTER.

When a WMA/MP3/MPEG-4 AAC or DivX video/WMV file is selected, playback begins from that file, and continues until the end of the folder.

When a JPEG file is selected, a slideshow begins, starting with that file, and continues to the end of the folder.

Tip

You can also play a JPEG slideshow while listening to WMA/MP3/MPEG-4 AAC playback. Simply select the audio file you want to listen to followed by the JPEG from which you want the slideshow to start. Playback of both the slideshow and the audio files repeats. Playback controls are effective for the JPEG slideshow only.

To play the contents of the whole disc rather than just the current folder, exit the Disc Navigator and start playback using the (play) button.

Using Playlists

With this feature, you can make up to three playlists of 30 files each for discs containing WMA, MP3, MPEG-4 AAC and JPEG files.

Since this unit will remember all playlists for the last ten discs you have loaded, this is useful if you have a large number of files that you

want to organize quickly and easily.2

Programming playlists

1With the disc stopped, press HOME MENU and select ‘Disc Navigator’ from the on-screen menu.

2Select the file you want to add to the playlist.

See Browsing Windows MediaTM Audio (WMA), MP3, MPEG-4 AAC, DivX video/WMV and JPEG files with the Disc Navigator above if you don’t know how to do this.

3 Press PLAYLIST 1, 2 or 3.

The file is added to the playlist you select.

4 Repeat steps 2 and 3 until you’re done.

Note

1You can also do this by going to the ‘..’ folder at the top, then pressing ENTER.

2The disc must be loaded for the files in your playlist to play back.

06

Español Nederlands Italiano Français Deutsch English

27

En

06 Disc playback features

Tip

To add files without the on-screen display, simply press PLAYLIST 1, 2 or 3 during normal playback of the file you want (except when a JPEG slideshow is playing at the same time as audio).

Listening to playlists

• With playback stopped, press PLAYLIST 1, 2 or 3.

During playback, PGM lights in the front panel

display. If no playlist has been programmed, NO LIST shows in the display.

If the playlist contains both JPEG and audio files, playback of the slideshow and audio files starts.

Clearing files from a playlist

1Start playback of your playlist.

2From the ‘Disc Navigator’ screen, highlight the file you want to remove from the playlist and press CLEAR.

4 Press ENTER on ‘B(End Point)’ to set the loop end point.

After pressing ENTER, playback jumps back to the start point and plays the loop.

5 To resume normal playback, select ‘Off’.

Using repeat play

In addition to various repeat play options, it’s also possible to use repeat play together with program play (see Creating a program list on page 29).

1During playback, press HOME MENU and select ‘Play Mode’.

2Select ‘Repeat’ then select a repeat play

option.1

If program play is active, select Program Repeat to repeat the program list, or Repeat Off to cancel.

For DVD discs, select Title Repeat or

Chapter Repeat.

For CDs and Video CD/Super VCDs, select

Disc Repeat or Track Repeat.

For DivX video/WMV discs, select Title Repeat (or Repeat Off).

Looping a section of a disc

The A-B Repeat function allows you to specify two points (A and B) within a track (CD, Video CD/Super VCD) or title (DVD) that form a loop which is played over and over.

1 During playback, press HOME MENU and select ‘Play Mode’.

Play Mode

2Select ‘A-B Repeat’.

3Press ENTER on ‘A(Start Point)’ to set the loop start point.

Using random play

Use this function to play titles or chapters (DVD-Video) or tracks (CD and Video CD/Super

VCD) in a random order.2

1During playback, press HOME MENU and select ‘Play Mode’.

2Select ‘Random’ then select an option.

For DVD discs, select Random Title or

Random Chapter.

For CDs and Video CD/Super VCDs, select On or Off to switch random play on or off.

Note

1You can’t use repeat play with WMA/MP3/MPEG-4 AAC discs.

2• You can set the random play option when a disc is playing or stopped. However, you can’t use random play together with program play.

You can’t use random play with VR format DVD-R/-RW discs, WMA/MP3/MPEG-4 AAC discs, DivX video/WMV discs, or while a DVD disc menu is being displayed.

28

En

Disc playback features

06

Tip

Use the following controls during random play:

Button

What it does

 

 

Selects a new track/title/chapter at random.

Returns to the beginning of the current track/title/chapter; further presses select another random track/title/chapter.

Random play remains in effect until you select Random Off from the random play menu options.

5 To play the program list, press (play).

Program play remains active until you turn off program play (see below), erase the program list (see below), eject the disc or switch off.

Tip

Use the following controls during program play:

Button

What it does

HOME

Save the program list and exit

MENU

without starting playback.

Skip to the next step in the program list.

Creating a program list

This feature lets you program the play order of titles/chapters/tracks on a disc.1

1During playback, press HOME MENU and select ‘Play Mode’.

2Select ‘Program’ then select ‘Create/Edit’ from the list of program options.

3Use / / / and ENTER to select a title, chapter or track for the current step in the program list.

For a DVD disc, you can add a title or a chapter.

For a CD or Video CD/Super VCD, select a track to add to the program list.

After pressing ENTER to select the title/ chapter/track, the step number automatically moves down one.

4 Repeat step 3 to build up a program list.

A program list can contain up to 24 steps.

You can insert steps by just highlighting the position where you want the new step to appear and entering a title/chapter/track number.

To delete a step, highlight it and press

CLEAR.

Other functions available from the program menu

There are a number of other options in the program menu in addition to Create/Edit.

Playback Start – Starts playback of a saved program list

Playback Stop – Turns off program play, but does not erase the program list

Program Delete – Erases the program list and turns off program play

Searching a disc

You can search DVD discs by title or chapter number, or by time; CDs and Video CD/Super VCDs by track number or time; DivX video/ WMV discs by time.

1Press HOME MENU and select ‘Play Mode’.

2Select ‘Search Mode’.

The search options that appear depend on the kind of disc loaded.

3Select a search mode.

The disc must be playing in order to use time search.

Note

1 You can’t use Program play with VR format DVD-R/-RW discs, WMA/MP3/MPEG-4 AAC discs, DivX video/WMV discs, or while a DVD disc menu is being displayed.

Español Nederlands Italiano Français Deutsch English

29

En

06 Disc playback features

4Use the number buttons to enter a title, chapter or track number, or a time.

For a time search, enter the number of minutes and seconds into the currently playing title (DVD/DivX video/WMV) or track (CD/Video CD/Super VCD) you want

playback to resume from. For example, press 4, 5, 0, 0 to have playback start from

45 minutes into the disc. For 1 hour, 20 minutes and 30 seconds, press 8, 0, 3, 0.

5Press ENTER to start playback.

Switching subtitles

Some DVD discs and DivX video discs have subtitles in one or more languages; the disc box will usually tell you which subtitle languages are available. You can switch

subtitle language during playback.1

• Press SHIFT+SUBTITLE repeatedly to select a subtitle option.

To set subtitle preferences, see Language settings on page 36.

See Displaying DivX subtitle files on page 48 for more on DivX subtitles.

Zooming the screen

Using the zoom feature you can magnify a part of the screen by a factor of 2 or 4, while watching a DVD, DivX video/WMV title or Video CD/Super VCD or playing a JPEG disc.

1During playback, press SHIFT+ZOOM to select the zoom factor (Normal, 2x or 4x).

2Use / / / to change the zoomed area.

You can change the zoom factor and the zoomed area freely during playback.4

Switching camera angles

Some DVD discs feature scenes shot from two or more angles — check the disc box for details.

When a multi-angle scene is playing, a icon appears on screen (this can be switched off if you prefer — see Display settings on page 37).

• During playback (or when paused), press SHIFT+ANGLE to switch angle.

Switching language/audio channels

When playing discs recorded with dialogue in two or more languages, or with dual-mono

audio2 you can switch these during playback.3

When playing a Video CD/Super VCD, you can switch between stereo, just the left channel or just the right channel.

• Press SHIFT+AUDIO repeatedly to select an audio language option.

To set audio language preferences, see

Language settings on page 36.

Displaying disc information

Various track, chapter and title information can be displayed on-screen during playback.

• To show/switch/hide the information displayed, press DISPLAY repeatedly.

Limited disc information also appears in the front panel display. Press DISPLAY to change

the displayed information.

Note

1Some discs only allow you to change subtitle language from the disc menu. Press TOP MENU or MENU to access.

2Some Super VCDs have two soundtracks. With these discs you can switch between the two soundtracks as well as individual channels in each.

3Some discs only allow you to change audio language from the disc menu. Press TOP MENU or MENU to access.

4• Since DVD, Video CD/Super VCD, DivX video/WMV title and JPEG pictures have a fixed resolution, picture quality will deteriorate, especially at 4x zoom. This is not a malfunction.

If the navigation square at the top of the screen disappears, press SHIFT+ZOOM again to display it.

30

En

USB playback and Recording

Chapter 7

USB playback and Recording

07

English

Using the USB interface

It is possible to listen to two-channel audio1 and watch DivX video/WMV/JPEG files using the USB interface on the front of this unit.

Connect a USB mass storage device2 as shown below.

1With the player switched on, press USB.

Make sure your TV is on and set to the correct video input.

2Connect your USB device.

The USB terminal is located on the front panel.

USB USB

(Type A)

USB mass storage device

3 Press (play) to start playback.

If your USB device contains JPEGs, a slideshow will start. See Playing a JPEG slideshow on page 25 for more on this.

Make sure USB DATA is showing in the front panel display (or the system is in standby) when disconnecting.

Important

If a USB ERR message lights in the display, it may mean that the power requirements of the USB device are too high for this player, or that the device is incompatible. Try the following:

Switch the player off, then on again.

Reconnecting the USB device with the player switched off.

Selecting to another input source (like DVD/CD), then back to USB.

Using a dedicated AC adapter (supplied with the device) for USB power.

If this doesn’t remedy the problem, it is likely your USB device is incompatible.

Recording the tracks of a music CD on a USB device

The tracks of a music CD loaded in this unit can be recorded on a USB connected to the USB port.

Recording all the tracks

1 Load the music CD.

Press to stop playback.

Español Nederlands Italiano Français Deutsch

Note

1This includes playback of DivX video/WMV/WMA/MP3/MPEG-4 AAC files (except files with copy-protection or restricted playback).

2• Compatible USB devices include external magnetic hard drives, portable flash memory (particularly keydrives) and digital audio players (MP3 players) of format FAT16/32. It is not possible to connect this unit to a personal computer for USB playback.

Pioneer cannot guarantee compatibility (operation and/or bus power) with all USB mass storage devices and assumes no responsibility for any loss of data that may occur when connected to this unit.

With large amounts of data, it may take longer for the system to read the contents of a USB device.

Some USB devices may not be properly recognized.

Even when they are in a supported format, some files may not play or display depending on the content.

31

En

07 USB playback and Recording

2 Press SHIFT+USB REC to display the ‘CD -> USB Rec’ screen.

CD –> USB Rec

Track 1–13

Select Track

 

Track01

01:43

Bitrate

128kbps

Track02

03:17

 

 

 

Track03

04:18

 

 

 

Track04

04:59

 

 

 

Track05

04:20

Start

 

 

Track06

04:38

Selected Track

13

Track07

04:40

Total Time

055:07

Track08

04:11

 

 

 

 

 

3 Press ENTER to start recording.

Recording starts. The screen shown below is displayed during recording.1

CD –> USB Rec

Track 1–13

Track Progress

 

 

Track01

01:43

 

 

 

 

 

Track02

03:17

Total Progress

 

 

Track03

04:18

 

 

 

 

 

Track04

04:59

 

 

 

 

 

Track05

04:20

 

 

 

 

 

 

 

Cancel

 

 

Track06

04:38

Selected Track

13

 

Track07

04:40

Total Time

055:07

 

Track08

04:11

 

 

 

 

 

 

 

Recording specific tracks

1Load the music CD.

Press to stop playback.

2Press HOME MENU and select ‘CD ->USB Rec’.

CD -> USB Rec can only be selected when the music CD is stopped.

CD – > USB Rec

3 Make setting using / / / and

ENTER.

CD –> USB Rec

 

 

 

 

 

Track 1–13

 

Select Track

Individual

Track01

01:43

Bitrate

Select All

Track02

03:17

 

 

All Clear

Track03

04:18

 

 

 

Track04

04:59

 

 

 

Track05

04:20

Start

 

 

Track06

04:38

Selected Track

00

Track07

04:40

Total Time

000:00

Track08

04:11

 

 

 

 

 

4 Select the track you want to record.

CD –> USB Rec

 

 

 

 

 

Track 1–13

 

Select Track

Individual

Track01

01:43

Bitrate

Select All

Track02

03:17

 

 

All Clear

Track03

04:18

 

 

 

Track04

04:59

 

 

 

Track05

04:20

Start

 

 

Track06

04:38

Selected Track

01

Track07

04:40

Total Time

003:17

Track08

04:11

 

 

 

 

 

Individual — Select one track at a time.

Select All — Select all the tracks.

All Clear — Clear all selected tracks.

5 Select the bit rate (transfer rate). Select 128 kbps, 192 kbps or 320 kbps.

CD –> USB Rec

Track 1–13

 

Select Track

128kbps

Track01

01:43

 

Bitrate

192kbps

Track02

03:17

 

 

 

320kbps

Track03

04:18

 

 

 

 

Track04

04:59

 

 

 

 

Track05

04:20

 

Start

 

 

Track06

04:38

 

Selected Track

03

Track07

04:40

 

Total Time

012:17

Track08

04:11

6 Select ‘Start’ using the / / /, then press ENTER.2

CD –> USB Rec

Track 1–13

Select Track

 

Track01

01:43

Bitrate

128kbps

Track02

03:17

 

 

 

Track03

04:18

 

 

 

Track04

04:59

 

 

 

Track05

04:20

Start

 

 

Track06

04:38

Selected Track

03

Track07

04:40

Total Time

012:17

Track08

04:11

 

 

 

 

 

Recording starts.

CD –> USB Rec

Track 1–13

Track Progress

 

 

Track01

01:43

 

 

 

 

 

Track02

03:17

Total Progress

 

 

Track03

04:18

 

 

 

 

 

Track04

04:59

 

 

 

 

 

Track05

04:20

 

 

 

 

 

 

 

Cancel

 

 

Track06

04:38

Selected Track

03

Track07

04:40

Total Time

012:17

Track08

04:11

 

 

 

 

 

 

 

Note

1Recording cannot be started if there is not enough free space on the USB device. In this case, “Available USB space is low” is displayed.

2• When recording is finished, a folder named “PIONEER” is created automatically on the USB device. The recorded tracks are stored in this folder.

Up to 99 “PIONEER” folders can be created.

Recording is not possible if the USB device contains 300 folders or more.

When recording on a USB device is under way, all DVD-related key operations are disabled except for the operation of

STANDBY/ON and OPEN/CLOSE buttons and switchover of the functions.

When the sleep timer is ON, it is cancelled once recording on a USB device is started.

32

En

Singing karaoke

Chapter 8

Singing karaoke

Singing karaoke

Using the karaoke features you can plug in a microphone and mix the sound of your own

voice with a backing track.1 You can select a backing track from audio sources such as CDs, DVDs, VCDs or USB devices. Adjust the microphone level relative to the backing track.

MAIN MIC SUB

1 Plug in the microphone(s).

If you’re only using one mic, plug it into the

MIC (MAIN) jack. The MIC (SUB) jack can be used only if MIC (MAIN) is also connected.

If the microphone has an on/off switch, make sure it’s on.

2 Load a karaoke backing disc.

You can also use tracks on a USB device as source material for a backing track.

OFF (default) – Switches the Karaoke mode off.

• Press SHIFT+AUDIO to switch between audio channels (except Data discs and USB sources) with discs that have vocal tracks on only one channel:

Left – Left channel only. Use for tracks that have a vocal recorded in the right channel. Right – Right channel only. Use for tracks that have a vocal recorded in the left channel. STEREO – Switches the Karaoke mode off.

4Play the backing track.

5Adjust the MIC VOL +/– to get the sound you want. 2

To avoid unpleasant feedback, make sure you

don’t point the microphone(s) at the speakers.3

Changing the vocal mix

Adding some effects to the microphone mix

can sometimes improve the overall sound.4 You can choose between three echo levels.

• To add effects to the microphone mix, press SHIFT+ECHO.

Pressing repeatedly switches between echo levels 1 to 3 and off.

3 Adjust KARAOKE mode settings.

• Press SHIFT+KARAOKE to turn KARAOKE mode on or off for discs that have vocals on both Left and Right channels:

KARAOKE (Vocal Fade) – Vocals in the backing track are partially eliminated.

Changing the backing track

You may want to lower or raise the pitch of the backing track to match your vocal range.5

• Press SHIFT+ or SHIFT+ to lower or raise the pitch of the backing track.

Note

1 • These features are only possible when a microphone is connected. If you try to use SHIFT+KARAOKE, SHIFT+ECHO, SHIFT+ , SHIFT+ or MIC VOL when no mic is connected, a NO MIC error message is displayed. Also note that during DVD

playback, when you connect a mic sound settings are automatically switched to STEREO playback and the player downmixes

multichannel sources to 2.1 channels.

• These features are only available with the DVD/CD or USB input functions.

2MIC VOL is set to 0 when you remove the microphone, change the function or turn the power off.

3Depending on the microphone level, the sound of the disc may distort. If this happens, turn down the volume.

4You cannot adjust SFC modes, tone controls (bass, treble, and bass boost), Extra Power mode, Front Surround mode, MP3 Expander mode or Voice Enhancer mode when a microphone is plugged in.

5This feature is not compatible with DTS signals.

08

Español Nederlands Italiano Français Deutsch English

33

En

09 Audio Settings and Video Adjust menus

Chapter 9

Audio Settings and Video Adjust menus

Audio Settings menu

The Audio Settings menu offers features for adjusting the way discs sound.

1 Press HOME MENU and select ‘Audio Settings’ from the on-screen display.

Audio Settings

2 Select and change settings using / / / and ENTER.

Audio Settings

Audio DRC

High

 

Medium

 

Low

 

Off

Audio DRC

Settings: High, Medium, Low,

Off (default)

When watching Dolby Digital DVDs at low volume, it’s easy to lose the quieter sounds completely — including some of the dialog. Switching Audio DRC (Dynamic Range Control) to on can help by bringing up the quieter sounds, while controlling loud peaks.

How much of a difference you hear depends on the material you’re listening to. If the material doesn’t have wide variations in volume, you

1 Press HOME MENU and select ‘Video Adjust’ from the on-screen display.

Video Adjust

2 Make settings using / / / and

ENTER.

Video Adjust

 

 

Sharpness

 

Standard

Brightness

 

0

Contrast

 

0

Gamma

 

Off

Hue

 

0

Chroma Level

 

0

 

 

 

You can adjust the following settings:

Sharpness – Adjusts the sharpness of edges in the picture (Fine, Standard, Soft)

Brightness – Adjusts the overall brightness (–20 to +20)

Contrast – Adjusts the contrast between light and dark (–16 to +16)

Gamma – Adjusts the ‘warmth’ of the picture (High, Medium, Low, Off)

Hue – Adjusts the red/green balance (Green 9 to Red 9)

Chroma Level – Adjusts how saturated colors appear (–9 to +9)

Adjust the Brightness, Contrast, Hue and Chroma Level settings using /.

may not notice much change.1

Video Adjust menu

From the Video Adjust screen you can adjust settings that affect picture presentation.

Brightness

min

max

0

 

 

 

 

3 Press ENTER to return to the Video Adjust screen, or HOME MENU to exit.

Note

1 Audio DRC is only effective with Dolby Digital audio sources.

34

En

Initial Settings menu

Chapter 10

Initial Settings menu

Using the Initial Settings menu

The Initial Settings menu provides audio and video output settings, parental lock settings, and display settings, among others.

If an option is grayed out it means that it cannot be changed at the current time. This is usually because a disc is playing. Stop the disc, then change the setting.

1Press DVD/CD.

2With playback stopped, press HOME MENU and select ‘Initial Settings’.

Initial Settings

3 Use / / / and ENTER to select the setting and option you want to set.

All the settings and options are explained on the following pages.1

Video Output settings

Setting

TV Screen

(See also Screen sizes and disc formats on page 51.)

Option

What it means

4:3 (Letter Box)

Set if you have a conventional 4:3 TV. Widescreen movies are

 

shown with black bars top and bottom.

 

 

4:3 (Pan & Scan)

Set if you have a conventional 4:3 TV. Widescreen movies are

 

shown with the sides cropped so that the image fills the screen.

 

 

16:9 (Wide)

Set if you have a widescreen TV.

 

 

16:9 (Compressed)

Set if you have a widescreen TV. 4:3 material is shown with

 

black bars on either side of the screen.2

Component Out

Interlace

Set if your TV is not compatible with progressive scan video.

(See also Connecting

 

 

Progressive

Set if your TV is compatible with progressive scan video (see

auxiliary audio

 

your TV’s instruction manual for details). Press ENTER once

components on

 

 

more to confirm (or RETURN to cancel).

page 40.)

 

 

Note that progressive scan video is only output from the

 

 

 

 

component video jacks.

 

 

 

Note

1• In the table, the default setting is shown in bold: other settings are shown in italics.

• Some settings, such as TV Screen, Audio Language and Subtitle Language may be overridden by the DVD disc. Often

these settings can also be made from the DVD disc menu.

• The HDMI Resolution and HDMI Color settings only need to be set if you connected this player to an HDMI-compatible component using the HDMI connector.

2 This setting can only be used when you are connected via HDMI and have the HDMI resolution set to 1920x1080p, 1920x1080i or 1280x720p. When using this setting, only the HDMI connection is available.

10

Español Nederlands Italiano Français Deutsch English

35

En

10 Initial Settings menu

Setting

Option

What it means

HDMI Resolution*

1920x1080p

Set if your TV supports 1920 x 1080 pixel progressive-scan video.

(See Connecting using

 

 

1920x1080i

Set if your TV supports 1920 x 1080 pixel interlace video.

HDMI on page 41.)

 

 

1280x720p

Set if your TV supports 1280 x 720 pixel progressive-scan video.

* Default changes with

 

 

720x480p (NTSC)/

Set if your TV supports 720 x 480 (NTSC)/720 x 576 (PAL) pixel

TV format (PAL/NTSC).

720x576p (PAL)

progressive-scan video.

 

 

 

 

 

720x480i (NTSC)/

Set if your TV supports 720 x 480 (NTSC)/720 x 576 (PAL) pixel

 

720x576i (PAL)

interlace video.

 

 

 

HDMI Color*

Full range RGB

If colors are weak, this gives brighter colors and deeper black

(See Connecting using

 

(default setting for HDMI-compatible DVI devices).

HDMI on page 41.)

 

 

RGB

Use this setting if colors appear overly rich on the Full Range

* Default changes

 

RGB setting.

depending on device

 

 

Component

Outputs 8-bit component video format (default setting for

connected.

 

HDMI-compatible devices).

 

 

 

 

 

 

 

 

Language settings

Setting

Option

What it means

Audio Language

English

If there is an English soundtrack on the disc, it is played.

 

 

 

 

Languages as displayed

If there is a language selected on the disc, it is played.

 

 

 

 

Other Language

Select to choose a language other than the ones displayed (see

 

 

Using the language code list on page 57).

 

 

 

Subtitle Language

English

If there are English subtitles on the disc they are displayed.

 

 

 

 

Languages as displayed

The subtitle language selected on the disc is displayed.

 

 

 

 

Other Language

Select to choose a language other than the ones displayed (see

 

 

Using the language code list on page 57).

 

 

 

DVD Menu

w/Subtitle Lang.

DVD disc menus are displayed in the same language as your

Language

 

selected subtitle language, if possible.

 

 

 

 

Languages as displayed

DVD menus are displayed in the selected language, if possible.

 

 

 

 

Other Language

Select to choose a language other than the ones displayed (see

 

 

Using the language code list on page 57).

 

 

 

Subtitle Display

On

Subtitles are displayed in your selected subtitle language.

 

 

 

 

Off

Subtitles are always off by default when you play a DVD disc.

 

 

 

36

En

Initial Settings menu

Display settings

Setting

Option

What it means

OSD Language

English

On-screen displays are shown in English.

 

 

 

 

Languages as displayed

On-screen displays are shown in the language selected.

 

 

 

Angle Indicator

On

A camera icon is displayed on-screen during multi-angle

 

 

scenes on a DVD disc.

 

 

 

 

Off

No multi-angle indication is shown.

 

 

 

Options settings

Setting

Option

What it means

 

Parental Lock

See Parental Lock below.

 

 

 

 

 

DivX(R) VOD

Display

See About DivX® VOD content below.

 

 

 

 

 

Speakers settings

Setting

Option

What it means

Speaker Distance

Specify the distance of your speakers from your listening

 

 

position (see Speaker Distance on page 39).

 

 

 

Parental Lock

Default level: Off; Default password: none; Default Country/Area code: us (2119)

To give you some control over what your children watch on your DVD player, some DVDVideo discs feature a Parental Lock level. If your player is set to a lower level than the disc, the disc won’t play.

Some discs also support the Country/Area Code feature. The player does not play certain scenes on these discs, depending on the Country/Area Code you set.

1 Select ‘Password’.

Initial Settings

Video Output

Parental Lock

Password

Language

DivX (R) VOD

Level Change

Display

 

Country Code

Options

 

 

Speakers

 

 

2 Use the number buttons to input a fourdigit password then press ENTER.

Changing your password

To change your password, confirm your existing password then enter a new one.

Registering a new password

1

Select ‘Password Change’, input your

Register a password to change the Parental

existing password, then press ENTER.

Lock level or enter a Country/Area code.1

2

Enter a new password and press ENTER.

 

Note

1• Not all discs use Parental Lock, and will play without requiring the password first.

• If you forget your password, you’ll need to reset the player to register a new password (see Resetting the system on page 57).

10

Español Nederlands Italiano Français Deutsch English

37

En

10 Initial Settings menu

Setting/changing the Parental Lock

1Select ‘Level Change’.

2Use number buttons to enter your password, then press ENTER.

3Select a new level and press ENTER.

Press repeatedly to lock more levels

(more discs will require the password); press to unlock levels. You can’t lock level 1.

Setting/changing the Country/Area code

You can find the Country/Area code list on page 58.

1Select ‘Country Code’, input your password, then press ENTER.

2Select a Country/Area code then press ENTER.

There are two ways you can do this:

Select by code letter: Use / to change the Country/Area code.

Select by code number: Press then use the number buttons to enter the four-digit Country/Area code.

The new Country/Area code takes effect after ejecting the disc once.

About DivX® VOD content

In order to play DivX VOD (video on demand) content on this player, you first need to register the player with your DivX VOD content provider. You do this by generating a DivX VOD registration code, which you submit to your

provider.1

Important

DivX VOD content is protected by a DRM (Digital Rights Management) system. This restricts playback of content to specific, registered devices.

If you load a disc that contains DivX VOD

content not authorized for your player, the message Authorization Error is displayed and the content will not play.

Displaying your DivX VOD registration code

1Press HOME MENU and select ‘Initial Settings’.

2Select ‘Options’, then ‘DivX (R) VOD’.

Initial Settings

 

 

Video Output

Parental Lock

Display

Language

DivX (R) VOD

 

Display

 

 

Options

 

 

Speakers

 

 

3 Select ‘Display’.

Your eight-digit registration code is displayed.

Make a note of the code as you will need it when you register with a DivX VOD provider.

Playing DivX® VOD content

Some DivX VOD content may only be playable for a fixed number of times. When you load a disc containing this type of DivX VOD content, the remaining number of plays is shown on-screen and you then have the option of playing the disc (thereby using up one of the remaining plays), or stopping. If you load a disc that contains expired DivX VOD content (for example, content that has

zero remaining plays), the message Rental Expired is displayed.

If your DivX VOD content allows an unlimited number of plays, then you may load the disc into your player and play the content as often as you like, and no message will be displayed.

Note

1 Resetting the player (as described in Resetting the system on page 57) will not cause you to lose your registration code.

38

En

Initial Settings menu

Speaker Distance

• Default setting: 3.0m

To get the best surround sound from your system, you should set up the speakers equal distances from your listening position.

1Press HOME MENU and select ‘Initial Settings’.

2Select ‘Speakers’, then ‘Speaker Distance’.

Initial Settings

Video Output

Speaker Distance

Language

 

Display

 

Options

 

Speakers

 

3 Use / to select a speaker.

Initial Settings

 

 

Video Output

 

 

Language

L

3.0m

Display

C

3.0m

Options

R

3.0m

Speakers

SR

3.0m

 

SL

3.0m

 

SW

3.0m

6 Press to go back to the speaker list if you want to modify another speaker, or press ENTER to exit the Speaker Distance screen.

4Press to change the speaker distance for the highlighted speaker.

5Use / to change the distance.

When you change the distance settings of the front left (L) or front right (R) speakers, all the other speaker distances change relative to it.

Front left/right (L/R) speaker distances can be set from 30 cm to 9 m in 30 cm increments.1

The center speaker (C) can be set from –2.1 m to 0 m relative to the front left/right speakers.

Surround left/right (SL/SR) speakers can be set from –6.0 m to 0 m relative to the front left/right speakers.2

The subwoofer (SW) can be set from –2.1 m to 0 m relative to the front left/right speakers.

Note

1The L and R speakers are paired; you can’t set them differently.

2Make sure to set them the same distance when using the Extra Power mode (page 23).

10

Español Nederlands Italiano Français Deutsch English

39

En

11 Other connections

Chapter 11

Other connections

Important

When making or changing connections on the rear panel of this unit, be sure to switch power off and disconnect the power cord from the wall socket.

After completing all connections, connect the power cord to the wall socket.

Outdoor antenna

 

To component

 

input

 

Indoor antenna

 

(vinyl-coated wire)

 

5 m to 6 m

TV

AM loop

 

 

antenna

LINE 1

R

FRONT

L

CENTER

L

 

 

 

 

AC IN

R

 

SUB

 

R

SURROUND

 

WOOFER

 

ANALOG

SPEAKERS (4 Ω )

 

From audio output

Tape deck, etc.

Connecting auxiliary audio components

Using the stereo analog inputs, you can connect an external component such as a tape deck or MD player for playback through this system.

For the connection diagram, see 1 above.

COMPONENT

PR

A

 

 

N

 

 

VIDEO

 

T

 

 

 

 

E

 

 

VIDEO(TV)

PB

N

 

 

N

 

FM

 

 

A

AM LOOP

UNBAL

 

Y

 

 

HDMI

ADAPTER PORT

VIDEO OUT

PAL connector

To

HDMI input

Bluetooth®

ADAPTER

From audio output

KURO LINK-compatible

Pioneer flat screen TV

• Connect the ANALOG AUDIO IN (LINE 1) jacks to the analog outputs of an external playback component.

Connect using RCA pin-plug stereo cables.

40

En

Other connections

Connecting using the component video output

If your TV has component video inputs, you can use these instead of the standard video outputs for a better quality picture.1

For the connection diagram, see 2 on page 40.

• Use a component video cable to connect the COMPONENT VIDEO OUT to a set of component inputs on your TV.

About progressive scan video

Compared to interlace video, progressive scan video effectively doubles the scanning rate of the picture, resulting in a very stable, flickerfree image. Progressive scan video is available only from the component video output.

Compatibility of this player with progressive-scan and high-definition TVs.

This player is compatible with progressive video Macro Vision System Copy Guard.2

Connecting using HDMI

If you have a HDMI or DVI (with HDCP) equipped monitor or display, you can connect it to this player using a commercially available

HDMI cable for high quality digital video.3

For the connection diagram, see 3 on page 40.

11

then press ENTER.

• Use an HDMI cable to connect the HDMI

English

OUT interconnect on this player to an HDMI

interconnect on a HDMI-compatible display.

• The arrow on the cable connector body

should be face down for correct alignment

 

with the connector on the player.

 

 

Deutsch

You can also adjust the HDMI settings for

Français

resolution and color. For more on these

settings see Video Output settings on page 35.

Switching the HDMI audio setting

You can select the system speaker or the TV

 

through the HDMI to output the audio sound of

Italiano

when HDMI audio is set to TV.

the DVD/CD or USB function.4 You cannot use

 

a number of sound functions of this system

 

1 Press SHIFT+SETUP.

Nederlands

2 Use / to select HDMI SET then press

 

ENTER.

 

3 Use / to choose HDMI MODE then

 

press ENTER.

 

4 Use / to choose the setting you want

Español

 

AMP – Output Audio sound of the DVD/CD and USB function signal from this system.

Note

1• The component video output is switchable between interlaced and progressive formats. See Video Output settings on page 35.

While the player is connected using HDMI cable, the component video output cannot be switched between Interlace and Progressive formats. When HDMI Resolution is set to 720x480i (NTSC)/720x576i (PAL), Interlace format is automatically selected, and Progressive format is automatically selected in other settings.

2Consumers should note that not all high-definition television sets are fully compatible with this product and may cause artifacts to be displayed in the picture. In case of 525 progressive scan picture problems, it is recommended that the user switch the connection to the ‘standard definition’ output (Interlace). If there are questions regarding our TV set compatibility with this model, please contact our customer service center.

3• An HDMI connection can only be made with DVI-equipped components compatible with both DVI and High Bandwidth Digital Content Protection (HDCP). If you choose to connect to a DVI connector, you will need a separate adaptor (DVI HDMI) to do so. A DVI connection, however, does not support audio signals. Consult your local audio dealer for more information.

Depending on the component you have connected, using a DVI connection may result in unreliable signal transfers.

When you change the component connected to the HDMI output, you will also need to change the HDMI settings to match the new component (see Video Output settings on page 35 to do this).

4It is not possible to switch this setting when KURO LINK setting is ON and flat screen TV is in synchronized amp mode.

41

En

11 Other connections

TV – Output Audio sound of the DVD/CD and USB function signal from a TV or flat screen TV.1

gigabytes per second (with HDTV signals), one connector (instead of several cables and connectors), and communication between the AV source and AV devices such as DTVs.

Resetting the HDMI connection

If you get an error message (the display shows HDMI ERR) or if the screen goes blank (for

example, after changing the resolution), check the troubleshooting guide on page 53. If this doesn’t solve the problem, follow the steps below to reset the HDMI connection.

1Press SHIFT+SETUP.

2Use / to select INITIAL then press

ENTER.

3Use / to choose HDMIINIT then press

ENTER.

4Press ENTER while INIT OK is blinking.

The system will restart and the HDMI settings are automatically reset to the factory defaults. See Video Output settings on page 35 for more on these settings.

About HDMI

HDMI (High Definition Multimedia Interface) supports both video and audio on a single digital connection for use with DVD players, DTV, set-top boxes, and other AV devices. HDMI was developed to provide the technologies of High Bandwidth Digital Content Protection (HDCP) as well as Digital Visual Interface (DVI) in one specification. HDCP is used to protect digital content transmitted and received by DVIcompliant displays.

HDMI has the capability to support standard, enhanced, or high-definition video plus standard to multichannel surround-sound audio. HDMI features include uncompressed digital video, a bandwidth of up to five

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC.

Connecting external antennas

For an external AM antenna, use 5 m to 6 m of vinyl-insulated wire and set up either indoors or outdoors. Leave the loop antenna connected. Only use the included AM loop antenna.

For an external FM antenna, use a PAL connector to hook up an external FM antenna.

For the connection diagram, see 4 on page 40.

Bluetooth® ADAPTER for Wireless Enjoyment of Music

HTZ280/282DVD-AP models only

Wireless music play

When the Bluetooth ADAPTER (Pioneer Model No. AS-BT100) is connected to this unit, a product equipped with Bluetooth wireless technology (portable cell phone, digital music player, etc.) can be used to listen to music

wirelessly.2 Also, by using a commercially available transmitter supporting Bluetooth wireless technology, you can listen to music on a device not equipped with Bluetooth wireless technology. The AS-BT100 model supports SCMS-T contents protection, so music can also be enjoyed on devices equipped with SCMS-T type Bluetooth wireless technology.

Note

1This makes it possible to use the TV’s built-in speakers to listen to the audio input from a DVD or USB device. Audio output from

the HDMI terminal is 2 channel linear PCM only. In this event, no sound will be heard from this unit’s speakers (or headphones). All other audio sources (including TUNER) are output from this unit normally.

2It may be necessary that the Bluetooth wireless technology enabled device supports A2DP profiles.

42

En

Other connections

11

Remote control operation

The remote control supplied with this system allows you to play and stop media, and perform

other operations.1

Bluetooth wireless technology enabled device: cell phone

 

Device not

 

equipped with

 

Bluetooth wireless

 

technology:

 

Digital music

Bluetooth wireless

player

technology

+

enabled device:

Bluetooth audio

Digital music

transmitter

player

(sold commercially)

Music data

Bluetooth®

ADAPTER

This unit

Remote control operation

Connecting Optional Bluetooth ADAPTER

1 Switch the system into standby and connect Bluetooth ADAPTER to the ADAPTER PORT located in the rear panel.

For the connection diagram, see 5 on page 40.

2Press STANDBY/ON.

3Press ADAPTER PORT and to switch to BT AUDIO input mode.2

Pairing Bluetooth ADAPTER and Bluetooth wireless technology device

“Pairing” must be done before you start playback of Bluetooth wireless technology content using Bluetooth ADAPTER. Make sure to perform pairing first time you operate the system or any time pairing data is cleared. “Pairing” is the step necessary to register Bluetooth wireless technology device to enable

Bluetooth communications.3 For more details, see also the operating instructions of your Bluetooth wireless technology device.

1Press SHIFT+SETUP to select BT SETUP, then press ENTER.

2Use / to select PAIRING, then press

ENTER.

3Select the PIN code to be used from 0000/ 1234/8888 using /, then press ENTER. PAIRING blinks.

CAUTION

You can use any of 0000/1234/8888 PIN codes. Bluetooth wireless technology device using any other PIN code cannot be used with this system.

4 Switch on the Bluetooth wireless technology device that you want to make pairing, place it near the system and set it into the pairing mode.

Español Nederlands Italiano Français Deutsch English

Note

1• It may be necessary that the Bluetooth wireless technology enabled device supports AVRCP profiles.

Remote control operations cannot be guaranteed for all Bluetooth wireless technology enabled devices.

2When the Bluetooth ADAPTER is not plugged in the ADAPTER PORT, BT AUDIO input mode cannot be entered even if

ADAPTER PORT is pressed.

3• Pairing is required when you first use Bluetooth wireless technology device and Bluetooth ADAPTER.

To enable Bluetooth communication, pairing should be done with both of your system and Bluetooth wireless technology device.

43

En

11 Other connections

5 Check to see that the Bluetooth ADAPTER is detected by the Bluetooth wireless technology device.

When the Bluetooth wireless technology device detects the Bluetooth ADAPTER, the adapter’s identification “AS-BT100” appears in

the Bluetooth wireless technology device list.1

6 From the Bluetooth wireless technology device list, select Bluetooth ADAPTER and

enter the PIN code selected in the step 3.2

Listening to Music Contents of Bluetooth wireless technology device with Your System

1Press ADAPTER PORT and to switch to BT AUDIO input mode.

2Connect the Bluetooth wireless technology device to the Bluetooth ADAPTER.

When Bluetooth wireless technology device is connected:

Bluetooth wireless technology device name appears in the system display.3

When Bluetooth wireless technology device is not connected:

NODEVICE appears in the system display.

3 Start playback of music contents stored in Bluetooth wireless technology device.

The following operations are now possible for Bluetooth wireless technology devices, using the button at the top of the system and remote

controller.4

Button

What it does

 

 

/ (system) Starts normal playback and pauses/unpauses playback.

Button

What it does

 

Starts normal playback.

(remote control)

 

 

 

 

Pauses playback.

(remote control)

 

 

 

(system/

Stops playback.

remote control)

 

 

 

 

Press to start fast reverse

(remote control)

scanning.

 

 

 

Press to start fast forward

(remote control)

scanning.

 

 

 

Skips to the start of the

(remote control)

current file, then previous

 

files.

 

 

 

Skips to the next file.

(remote control)

 

Clearing Pairing5

1Press SHIFT+SETUP, select BT SETUP, then press ENTER.

2Use / to select PAIR CLR, then press

ENTER.

3When CLR OK appears, press ENTER.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Pioneer Corporation is under license. Other trademarks and trade names are those of their respective owners.

Note

1When a Bluetooth wireless technology device does not appear in the list of detected devices or has no display, the Bluetooth wireless technology device list does not appear. In some cases, you may pair the Bluetooth ADAPTER and that Bluetooth wireless technology device by using the pairing mode.

2PIN code may in some case be referred to as PASSKEY.

3The system can display alphanumeric characters only. Other characters may not be displayed correctly.

4Bluetooth wireless technology device should be compatible with AVRCP profile.

Depending on Bluetooth wireless technology device you use, operation may differ from what is shown in this table.

5• Clearing should be done with Bluetooth wireless technology device being disconnected.

When you connect Bluetooth wireless technology device again after clearing, repeat the pairing steps referring to Pairing Bluetooth ADAPTER and Bluetooth wireless technology device on page 43.

44

En

KURO LINK

12

Chapter 12

KURO LINK

Not applicable to the HTZ180/181DVD models

By connecting this unit to a KURO LINKcompatible Pioneer flat screen TV with a HDMI cable, you can control this unit from the remote control of a connected flat screen TV, as well as have the connected flat screen TV automatically change inputs in response to operations carried out on this unit.

In addition, when language information is input from the connected flat screen TV, this unit’s GUI display language automatically changes (only when playback is stopped and GUI screen is not displayed, with DVD/CD function only).

Refer to the operating instructions for your flat screen TV for more information about which operations can be carried out by connecting via HDMI cable.

You cannot use this function with components that do not support KURO LINK.

We cannot guarantee this unit will work with KURO LINK-compatible components other than those made by Pioneer.

Making the KURO LINK connections

You can use synchronized operation for a connected flat screen TV.

Be sure to connect the flat screen TV’s audio cable to the audio input of this unit.

For the connection diagram, see 3 on page 40.

KURO LINK may not operate properly if you do not use a High Speed HDMI cable.

Connect the flat screen TV directly to this unit. Interrupting a direct connection with other amps or an AV converter (such as an HDMI switch) can cause operational errors.

English

HDMI input

KURO LINK-compatible

Deutsch

 

 

Pioneer flat screen TV

 

 

HDMI cable

Français

HDMI output

 

 

 

HDMI input

Other amps

 

 

or AV converter

 

 

HDMI cable

Italiano

HDMI OUT

 

 

 

 

This unit

 

Important

Nederlands

 

• When connecting this system or changing

 

connections, be sure to switch the power

 

off and disconnect the power cord from the

 

 

wall socket.

Español

After completing all connections, connect

 

the power cords to the wall socket.

 

KURO LINK Setup

You must adjust the settings of this unit as well as KURO LINK-compatible connected components in order to make use of the KURO LINK function. For more information see the operating instructions for each component.

Setting the KURO LINK mode

Choose whether to set this unit’s KURO LINK function ON or OFF. You will need to set it to LINK ON to use the KURO LINK function.

When using a TV that does not support the KURO LINK function, set this to LINK OFF.

45

En

12 KURO LINK

1Press SHIFT+SETUP.

2Use / to select HDMI SET then press

ENTER.

3Use / to select KURO LINK, then press ENTER.

4Use / to select the setting then press

ENTER to confirm.

LINK ON – Enables the KURO LINK function.

LINK OFF – The KURO LINK is disabled. Synchronized operations cannot be used.

Before using synchronization

Once you have finished all connections and settings, you must:

1Put all components into standby mode.

2Turn the power ON for all components, with the power for the flat screen TV being turned on last.

3Choose DVD/CD and see if video output displays properly on the screen or not.

Synchronized amp mode

The synchronized amp mode can be set from the KURO LINK-compatible TV’s remote control. See the explanation below for

operations in the synchronized amp mode.

These functions are set from the TV’s menu screen. For more information, refer to the operating instructions of the KURO LINKcompatible TV.

Synchronized amp mode operations

When using the synchronized amp mode, the KURO LINK-compatible component connected to this unit operates in sync as described below.

The unit’s volume can be set and the sound can be muted using the TV’s remote control.

46

When the TV’s power is set to standby, the unit’s power is also set to standby. (The unit’s power is automatically turned off when the TV’s power is turned off while a video DVD is being played on the unit. However, the unit’s power may not turn off automatically in some cases, for example, if you are listening to a CD or radio and turn off the output device.)

The unit’s input switches automatically when the TV’s channel is switched.

The synchronized amp mode remains in effect even if the unit’s input is switched to a function other than the DVD/CD.

The operations below can also be used on Pioneer KURO LINK-compatible flat screen TVs.

When the unit’s volume is adjusted or the sound is muted, the volume status is displayed on the flat screen TV’s screen.

When the OSD language is switched on the flat screen TV, the unit’s language setting also switches accordingly.

Canceling synchronized amp mode

When the synchronized amp mode is canceled, the unit’s power turns off if you were viewing a TV program on the TV.

When in the synchronized amp mode, the synchronized amp mode is canceled when the unit’s power is turned off. To turn the synchronized amp mode back on, select the synchronized amp mode using the TV’s remote control.

When in the synchronized amp mode, the synchronized amp mode is canceled if an operation that produces sound from the TV is performed from the TV’s menu screen, etc.

En

Additional information

Chapter 13

Additional information

Disc/content format playback compatibility

This player is compatible with a wide range of disc types (media) and formats. Playable discs will generally feature one of the following logos on the disc and/or disc packaging. Note however that some disc types, such as recordable CD and DVD, may be in an unplayable format.

See the Disc compatibility table below for more information.

About DualDisc playback

A DualDisc is a new two -sided disc, one side of which contains DVD content video, audio, etc. while the other side contains non-DVD content such as digital audio material.

The non-DVD, audio side of the disc is not compliant with the CD Audio specification and therefore may not play.

The DVD side of a DualDisc plays in this product. DVD-Audio content will not play.

For more detailed information on the DualDisc specification, please refer to the disc manufacturer or disc retailer.

DVD-Video DVD-R DVD-RW

Audio CD

Video CD

CD-R

CD-RW

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fujicolor CD

This unit will play DVD+R/+RW discs.

is a trademark of FUJIFILM Corporation.

is a trademark of DVD Format/Logo Licensing Corporation.

Also compatible with KODAK Picture CD.

This player supports the IEC’s Super VCD standard for superior picture quality, dual soundtracks, and widescreen support.

Super Video CD (Super VCD)

Disc compatibility table

Media

Compatible formats

CD-R/-RW • CD-Audio, Video CD/Super VCD, ISO 9660 CD-ROM* containing MP3, WMA, MPEG-4 AAC, JPEG or DivX video/WMV files.

* ISO 9660 Level 1 or 2 compliant. CD physical format: Mode1, Mode2 XA Form1. Romeo and Joliet file systems are both compatible.

Multi-session playback: No

Unfinalized disc playback: No

DVD-R/-RW • DVD-Video (Video mode), Video Recording (VR)*, UDF Bridge DVD-ROM containing MP3, WMA, MPEG-4 AAC, JPEG or DivX video/WMV files.

* Edit points may not play exactly as edited; screen may go momentarily blank at edited points.

Multi Border playback: No

Unfinalized playback: No

PC-created • Discs recorded using a PC may not disc be playable due to the setting of the

software used to create the disc. In these instances, check the DVD-R/-RW or CD-R/-RW software manual or disc boxes for more on compatibility.

• Discs recorded in packet write mode are not compatible.

13

Español Nederlands Italiano Français Deutsch English

47

En

13 Additional information

Media

Compatible formats

About DivX

 

 

 

Compressed • MPEG-1 Audio Layer 3 (MP3),

audio Windows Media Audio (WMA), MPEG- 4 AAC

• Sampling rates: 32 kHz/44.1 kHz/ 48 kHz

Bit-rates: Any (128 kbps or higher recommended)

VBR (variable bit rate) MP3/WMA/ DivX is a digital video format created by DivX,

MPEG-4 AAC playback: No

WMA lossless encoding: No

DRM (Digital Rights Management) compatible: Yes (DRM-protected audio files will not play in this player.)

File extensions: .mp3, .wma, .m4a (these must be used for the player to recognize MP3/WMA/MPEG-4 AAC files)

File structure (may differ): Up to 299 folders on a disc; up to 648 folders and files (combined) within each folder

JPEG file • Baseline JPEG and EXIF 2.2* still image files up to a resolution of 3072 x 2048

*File format for digital still cameras

Progressive JPEG compatible: No

File extensions: .jpg (must be used for the player to recognize JPEG files)

File structure (may differ): Up to 299 folders on a disc; up to 648 folders and files (combined) within each folder

Inc. This player can play DivX videos recorded on DVDs, CDs, or USB storage devices.

Keeping the same terminology as DVD-Video, individual DivX video files are called “Titles”.

DivX video compatibility

Plays DivX® video1

File extensions: .avi and .divx (these must be used for the player to recognize DivX video files). Note that all files with the .avi extension are recognized as MPEG4, but not all of these are necessarily DivX video files and therefore may not be playable on this player.

Displaying DivX subtitle files

The font sets listed below are available for DivX

external subtitle files. You can see the proper font set on-screen by setting the Subtitle Language (in Language settings on page 36)

About DVD+R/DVD+RW compatibility

Only DVD+R/DVD+RW discs recorded in ‘Video Mode (DVD Video Mode)’ which have been finalized, can be played back. However, some editing made during the recording may not be played back accurately.

to match the subtitle file.2

Group 1: Albanian (sq), Basque (eu), Catalan (ca), Danish (da), Dutch (nl), English (en), Faroese (fo), Finnish (fi), French (fr), German (de), Icelandic (is), Irish (ga), Italian (it), Norwegian (no), Portuguese (pt), Rhaeto-Romanic (rm), Scottish (gd), Spanish (es), Swedish (sv)

Group 2: Albanian (sq), Croatian (hr), Czech (cs), Hungarian (hu), Polish (pl), Romanian (ro), Slovak (sk), Slovenian (sl)

Note

1Playback of .avi video files larger than 4 GB is not possible.

2• For external subtitle files the following subtitle format filename extensions are supported (please note that these files are not shown within the disc navigation menu): .srt, .sub, .ssa, .smi

Some external subtitle files may be displayed incorrectly or not at all.

The filename of the movie file has to be repeated at the beginning of the filename for the external subtitle file.

The number of external subtitle files which can be switched for the same movie file is limited to a maximum of 10.

48

En

Additional information

13

Group 3: Bulgarian (bg), Byelorussian (be),

Macedonian (mk), Russian (ru), Serbian (sr),

Ukrainian (uk)

Group 4: Hebrew (iw), Yiddish (ji)

Group 5: Turkish (tr)

DivX® is a registered trademark of DivX, Inc., and is used under license.

About WMV

WMV is an acronym for Windows Media Video and refers to a video compression technology developed by Microsoft Corporation. WMV content can be encoded by using Windows Media Encoder.

This player is compatible with WMV9 files that are encoded by using the Windows Media Encoder 9 Series, with .wmv as an extension.

Compatible with size under 720 x 576 pixels/ 720 x 480 pixels.

Advanced Profile is not supported.

DRM-protected video files will not play in this player.

File extensions .wmv.

Compatible with bit rate under 192 kbps.

About MPEG-4 AAC

Advanced Audio Coding (AAC) is at the core of the MPEG-4 AAC standard, which incorporates MPEG-2 AAC, forming the basis of the MPEG-4 audio compression technology. The file format and extension used depend on the application used to encode the AAC file. This unit plays

back AAC files encoded by iTunes® bearing the extension ‘.m4a’. DRM-protected files will not play, and files encoded with some versions of

iTunes® may not play, or filenames may display incorrectly.

Apple and iTunes are trademarks of Apple Inc., registered in the U.S. and other countries.

About WMA

This player can playback Windows Media Audio content.

WMA is an acronym for Windows Media Audio

English

and refers to an audio compression technology

 

developed by Microsoft Corporation. WMA

 

content can be encoded by using Windows

 

Media Player version 7.7.1, Windows Media

 

Player for Windows XP, or Windows Media

 

Player 9 series.

Deutsch

Windows Media is a trademark of Microsoft

 

Corporation.

 

This product includes technology owned by

 

Microsoft Corporation and cannot be used or

 

distributed without a license from Microsoft

Français

Licensing, Inc.

 

Using and taking care of discs

Handling discs

Italiano

 

Hold the disc by its edges when handling so as

 

not to leave fingerprints, dirt or scratches on

 

either side of the disc. Damaged or dirty discs

 

can affect playback performance.

Nederlands

If a disc becomes marked with fingerprints,

 

dust, etc., clean using a soft, dry cloth.

 

Wipe lightly from the center of the disc using

Español

 

straight strokes. Don’t wipe the disc surface

 

with circular strokes.

 

If necessary, use a cloth soaked in alcohol, or a commercially available CD/DVD cleaning kit to clean a disc more thoroughly. Never use benzine, thinner or other cleaning agents such as those designed for cleaning vinyl records.

Storing discs

Avoid leaving discs in excessively cold, humid, or hot environments (including under direct sunlight). Don’t glue paper or put stickers onto the disc, or use a pencil, ball-point pen or other sharp-tipped writing instrument. These could all damage the disc.

49

En

13 Additional information

Discs to avoid

Discs spin at high speed inside the player. If a disc is cracked, chipped, warped, or otherwise damaged, don’t risk using it in your player — you could end up damaging the unit.

This unit is designed for use with conventional, fully circular discs only. Pioneer disclaims all liability arising in connection with the use of shaped discs.

DVD Video regions

All DVD Video discs carry a region mark that indicates which region(s) of the world the disc is compatible with. Your DVD system also has a region mark (on the rear panel). Discs from incompatible regions will not play in this player. Discs marked ALL play in any player.

When you insert a disc that cannot be played on this player, one of the following messages is displayed:

Incompatible disc region number Can’t play disc

Installation and maintenance

Hints on installation

We want you to enjoy using this system for years to come, so please bear in mind the following points when choosing a location:

Do...

Use in a well-ventilated room.

Place on a solid, flat, level surface, such as a table, shelf or stereo rack.

Don’t...

Use in a place exposed to high temperatures or humidity, including near radiators and other heat-generating appliances.

Place on a window sill or other place where the system will be exposed to direct sunlight.

Use in an excessively dusty or damp environment.

Place directly on top of an amplifier, or other component in your stereo system that becomes hot in use.

Use near a television or monitor as you may experience interference — especially if the television uses an indoor antenna.

Use in a kitchen or other room where the system may be exposed to smoke or steam.

Use on a thick rug or carpet, or cover with cloth

— this may prevent proper cooling of the system unit.

Place on an unstable surface, or one that is not large enough to support all four of the system unit’s feet.

Cleaning the pickup lens

The DVD player’s lens should not become dirty in normal use, but if for some reason it should malfunction due to dust or dirt, consult your nearest Pioneer authorized service center. Although lens cleaners are commercially available, we do not recommend using them since some may damage the lens.

Problems with condensation

Condensation may form inside the player if it is brought into a warm room from outside, or if the temperature of the room rises quickly. Although the condensation won’t damage the player, it may temporarily impair performance. Leave it to adjust to the warmer temperature for about an hour before switching on.

Moving the system unit

If you need to move the main unit, first remove

a disc if there’s one in the player, then pressSTANDBY/ON on the front panel to turn the

system off. Wait for -OFF- to disappear from

the display, then unplug the power cord.1 Never lift or move the unit during playback — discs rotate at high speeds and may damage.

Note

1 Unplugging the unit before -OFF- disappears from the display may cause the system to return to the factory settings.

50

En

Additional information

Screen sizes and disc formats

DVD-Video discs come in different screen aspects, ranging from TV programs, which are generally 4:3, to CinemaScope widescreen

movies1, with an aspect ratio of up to about 7:3. Televisions also come in different aspect ratios; ‘standard’ 4:3 and widescreen 16:9.2

Set to 4:3 (Pan & Scan), widescreen discs are shown with the left and right sides cropped. Although the picture looks larger, you don’t actually see the whole picture.

Please note that many widescreen discs override the player’s setting so that the disc is shown in letter box format regardless of the setting.

Widescreen TV users

If you have a widescreen TV, the TV Screen

setting (page 35) of this player should be set to 16:9 (Wide) or 16:9 (Compressed).

When you watch discs recorded in 4:3 format with the 16:9 (Wide) setting, you can use the

TV controls to select how the picture is presented. Your TV may offer various zoom and stretch options; see the instructions that came with your TV for details.

Please note that some movie aspect ratios are wider than 16:9, so even though you have a widescreen TV, these discs will still play in a ‘letter box’ style with black bars at the top and bottom of the screen.

TV system setting

The default setting of this system is AUTO, and unless you notice that the picture is distorted when playing some discs, you should leave it set to AUTO. If you find picture distortion with some discs, set the TV system to match your country or region’s system. However, this may restrict the kinds of disc you can watch. See the table for the kinds of discs compatible with each setting (AUTO, PAL and NTSC).3

1Press SHIFT+SETUP.

2Use / to select SYS SET then press

ENTER.

Standard TV users

If you have a standard TV, the TV Screen

setting (page 35) of this player should be set to 4:3 (Letter Box) or 4:3 (Pan & Scan),

depending on which you prefer.

Set to 4:3 (Letter Box), widescreen discs are shown with black bars top and bottom.

3 Use / to choose TV SYS then press

ENTER.

The TV system changes as follows:

AUTO NTSC

NTSC PAL

PAL AUTO

Note

1Many widescreen discs override the system’s settings so that the disc is shown in letterbox format regardless of the setting.

2Using the 16:9 (Wide) or 16:9 (Compressed) setting with a standard 4:3 TV, or one of the 4:3 settings with a widescreen TV,

will result in picture distortion.

3 Most models of the newly developed countdown PAL TV system detect 50 Hz (PAL)/60 Hz (NTSC) and automatically switch vertical amplitude, resulting in a display without vertical shrinkage. However, in some cases, the image may appear without color. If your PAL TV does not have a V-Hold control, you may not be able to watch NTSC discs because of picture roll. If the TV has a V-Hold control, adjust it until the picture stops rolling. On some TVs, the picture may shrink vertically, leaving black bands at the top and bottom of the screen.

13

Español Nederlands Italiano Français Deutsch English

51

En

13 Additional information

4 Press ENTER while CHANGE is blinking.

The system will automatically enter standby mode, then turn on again. You’ll see the new TV system setting in the display after seeing

POWER ON.1

 

 

Player setting

Media Type

Format

NTSC

PAL

AUTO

 

 

 

 

 

DVD/Super VCD/

NTSC

NTSC

PAL

NTSC

Video CD/DivX

PAL

NTSC

PAL

PAL

video/WMV

 

 

 

 

 

 

 

 

 

CD/MP3/WMA/

NTSC

PAL

NTSC or

MPEG-4 AAC/

 

 

 

PAL

JPEG/no disc

 

 

 

 

 

 

 

 

 

Setting the Key Lock

You can disable the front panel buttons by switching the Key Lock feature on.

1Press SHIFT+SETUP.

2Use / to select SYS SET then press

ENTER.

3Use /to choose KEYLOCK then press

ENTER.

4Use / to select LOCK ON or LOCK OFF then press ENTER.

Frequency step setting

Not applicable to Saudi Arabia, Israel, South Africa, other middle eastern contries and duty free models

If you find that you can’t tune into stations successfully, the frequency step may not be suitable for your country/region.

1Press SHIFT+SETUP.

2Use / to choose AM 9K/10K then press ENTER.

3Use / to select AM 9K or AM 10K then press ENTER.

Dimming the Display

You can adjust the brightness of the text in the front panel display.

1Press SHIFT+SETUP.

2Use / to select SYS SET then press

ENTER.

3Use / to select DIMMER then press

ENTER.

This is shown in the front panel display.

4 Use / to select LIGHT or DARK then press ENTER.

Note

1 You have to switch the player into standby (press STANDBY/ON) before each change.

52

En

Additional information

Troubleshooting

Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.

If the system does not operate normally due to external effects such as static electricity, disconnect the plug from the outlet and insert again to return to normal operating conditions.

General

Problem Remedy

The power does not turn on, or switches off suddenly (an error message may be displayed at startup).

Wait for one minute before switching back on.

Make sure there are no loose strands of wire touching the unit. This could cause the system to shut off automatically.

Check that the speakers are connected correctly.

Make sure the voltage of the mains power source is correct for the model.

Try reducing the volume level.

If the problem persists, take it to your nearest Pioneer authorized service center or your dealer for servicing.

No sound is output when

• If you’re using the line input, make sure the component is connected correctly (see

a function is selected.

Connecting auxiliary audio components on page 40).

 

• No audio is output from the speakers connected to this unit if HDMI audio mode is

 

set to TV (page 41).

 

• Press MUTE on the remote control to turn muting off.

 

• Turn up the volume.

 

 

No sound from surround

• Refer to Setting the channel levels on page 17 to check the speaker levels.

or center speakers.

• When TUNER, ADAPTER PORT or LINE is selected, you can only hear the source

 

in stereo. Switch the input source to DVD/CD or USB for multichannel sound.

 

• Check that you haven’t selected the STEREO mode (see Listening in surround

 

sound on page 22).

 

• Check if a microphone is connected or not.

 

• Connect the speakers properly (see Basic connections on page 9).

 

 

Can’t operate the remote

• Replace the batteries (see Putting the batteries in the remote control on page 15).

control.

• Operate within 7 m, 30° of the remote sensor (see Using the remote control on

 

page 16).

 

• Remove any obstacles or operate from another position.

 

• Avoid exposing the remote sensor on the front panel to direct light.

 

 

The microphone can’t be

• You are only using one microphone and it’s plugged into the MIC (SUB) jack. The

heard.

MIC (SUB) jack can only be used if there is also a microphone plugged into the MIC

 

(MAIN) jack.

 

• Adjust the MIC VOL +/–.

 

 

Feedback noise when

• The mic is pointing toward the speakers. Keep the mic pointed away from the

mic is switched on.

speakers.

 

• The microphone level is set too high. Turn down the mic control level.

 

 

TRAYLOCK shows in the

• Press and hold OPEN/CLOSE on the front panel for about eight seconds. Then

display and the tray can’t

the tray can be opened/closed using OPEN/CLOSE.

be ejected.

 

 

 

13

Español Nederlands Italiano Français Deutsch English

53

En

13 Additional information

DVD/CD/Video CD player

Problem

Remedy

The disc is ejected

• Clean the disc and align the disc properly in the disc guide.

automatically after

• If the region number on a DVD-video disc does not match the number on the

loading.

player, the disc cannot be used (see DVD Video regions on page 50). In this instance,

 

one of the following messages appears on screen: Incompatible disc region

 

number/Can’t play disc.

 

• Allow time for any condensation inside the player to evaporate. Avoid using the

 

player near an air-conditioning unit.

 

 

Playback not possible.

• If the disc is loaded upside down, reload the disc with label side face up.

 

 

Picture playback stops

• Press (stop), then (play) to start playback again.

and buttons cannot be

• Switch the power off once, then on again using the front panel STANDBY/ON

used.

button.

 

 

Settings are canceled.

• When the power is cut, settings will be canceled.

 

 

No picture/No color.

• Check that connections are correct and that plugs are inserted fully.

 

• Check the manual of the TV/monitor to make sure the settings are correct.

 

• If the Progressive setting is selected and you have used component video cables

 

to connect a TV that is not compatible with a progressive scan signal, you will not

 

be able to see any picture at all. With your TV connected using either the

 

composite or S-video terminals, change the Component Out setting to Interlace

 

(see Video Output settings on page 35).

 

 

Screen is stretched or

• The TV Screen setting is incorrect. Set the TV Screen option to match the TV/

aspect doesn’t change.

monitor you’re using (see Video Output settings on page 35).

 

 

When recorded on a VCR

• This system uses copy-protection technology which may prevent recording or

or passed through an AV

cause picture problems when connected through a VCR or AV selector. This is not a

selector, there is

malfunction.

disturbance in the

 

playback picture.

 

 

 

Picture disturbance

• This player is compatible with Macro-Vision System copy guard. Some discs

during playback or dark.

include a copy prevention signal, and when this type of disc is played back, stripes

 

etc., may appear on some sections of the picture depending on the TV. This is not a

 

malfunction.

 

• Discs respond differently to particular player functions. This may result in the

 

screen becoming black for a brief instant or shaking slightly when the function is

 

executed. These problems are largely due to differences between discs and disc

 

content and are not malfunctions of this player.

 

 

Noticeable difference in

• DVDs and CDs use different recording methods. This is not a malfunction.

DVD and CD volume.

 

 

 

CD-ROM disc is not

• Make sure that the CD-ROM was recorded using the ISO 9660 disc format. See

recognized.

Disc compatibility table on page 47 for more on disc compatibility.

 

 

DVD-ROM disc is not

• Make sure that the DVD-ROM was recorded using the UDF bridge format. See Disc

recognized.

compatibility table on page 47 for more on disc compatibility.

Files don’t show up in the Disc Navigator/Photo Browser.

• The files on the disc must be named with the correct file extension: .mp3 for MP3 files; .wma for WMA files; .m4a for MPEG-4 AAC files; .jpg for JPEG files (upper or lower-case is OK). See Disc compatibility table on page 47.

Can’t play WMA or

• The files were recorded using DRM (digital rights management). This is not a

MPEG-4 AAC files.

malfunction.

 

 

54

En

Additional information

13

Problem

Remedy

Can’t play WMV files.

• When the bit rate the file is more than 192 kbps, the file cannot be played back.

 

 

Tuner

Problem

Remedy

Considerable noise in

• Connect the AM antenna (see Basic connections on page 9) and adjust the

radio broadcasts.

direction and position for best reception. You may also connect an additional internal

 

or external AM antenna (refer to Connecting external antennas on page 42).

 

• Fully extend the FM wire antenna, position for best reception, and secure to a wall.

 

You may also connect an outdoor FM antenna (see Connecting external antennas on

 

page 42).

 

• Turn off other equipment that may be causing the noise or move it further away.

 

• The tuning interval is incorrect for your country or region. See Frequency step

 

setting on page 52 to switch the tuning interval.

 

 

Auto tuning does not

• The radio signal is weak. Auto tuning will only detect radio stations with a good

pick up some stations.

signal. For more sensitive tuning, connect an outdoor antenna.

 

 

USB connection

Problem

Remedy

USB mass storage device

• Make sure you have completely inserted the USB connector to this unit.

is not recognized by the

• Check that the memory format is FAT16 or FAT32.

system.

• USB devices with an internal USB hub are not supported.

 

 

Files don’t show up in the

• The files must have the correct file extension: .mp3 for MP3 files; .wma for WMA

Navigator/Photo

files; .m4a for MPEG-4 AAC files; .jpg for JPEG files (upper or lower-case is OK).

Browser.

• Make sure the file permission hasn’t been restricted (through a password, etc.).

 

 

Can’t play WMA or

• The files were recorded using DRM (digital rights management). This is not a

MPEG-4 AAC files.

malfunction.

 

 

HDMI connection

Problem

Remedy

No HDMI video output.

• Make sure that you’ve selected this player as the HDMI input in the settings for the

 

component you’re using (refer to the component’s instruction manual).

 

• Check that the HDMI cable is connected properly and isn’t damaged.

 

• Check that components connected using the HDMI interface are switched on and

 

HDMI compatible (components must be compatible with both DVI and High

 

Bandwidth Digital Content Protection (HDCP)).

 

• Depending on the component you have connected, using a DVI connection may

 

result in unreliable signal transfers.

 

• Make sure the resolution on this player matches that of the component you have

 

connected using HDMI. See Video Output settings on page 35 to change the HDMI

 

resolution.

 

• If the screen goes blank after changing the resolution, it means the resolution you

 

selected is incompatible with your monitor. See Resetting the HDMI connection on

 

page 42 to reset to the factory defaults.

 

 

Color problems occur

• Depending on the connected equipment, some HDMI Color settings may cause

with your monitor after

the picture to be displayed incorrectly. In this case, use the TV’s own video input

changing the HDMI Color

settings to select RGB, if possible. Alternatively, revert to the previous HDMI Color

setting (page 36).

setting.

 

 

Español Nederlands Italiano Français Deutsch English

55

En

13 Additional information

Problem

Remedy

No picture or sound.

• If the problem still persists when connecting your HDMI component directly to your

 

monitor, please consult the component or monitor manual or contact the

 

manufacturer for support.

 

 

No HDMI audio output.

• See Switching the HDMI audio setting on page 41 to make sure that TV is

 

selected.

 

 

KURO LINK does not

• Verify that the HDMI cable is firmly connected.

function.

• Make sure that this unit’s KURO LINK mode is set to LINK ON (page 45).

 

• Check whether the connected component supports KURO LINK or not. For more

 

information refer to the operating manual of your flat screen TV.

 

• KURO LINK may not work properly if a SCART cable and an HDMI cable are

 

connected simultaneously. Set KURO LINK mode to LINK OFF when connecting

 

SCART and HDMI cables simultaneously.

 

 

Your TV automatically

• The connected TV automatically may change inputs in response to this unit

change inputs.

starting playback DVD or having the GUI screen (ex. Disc Navigator) displayed, etc. If

 

you do not want your TV to change inputs in this way, set this unit KURO LINK mode

 

to LINK OFF (page 45).

 

 

Bluetooth connection

Problem Remedy

The Bluetooth wireless technology device cannot be connected or operated. Sound from the Bluetooth wireless technology device is not emitted or the sound is interrupted.

Check that no object that emits electromagnetic waves in the 2.4 GHz band (microwave oven, wireless LAN device or Bluetooth wireless technology apparatus) is near the unit. If such an object is near the unit, set the unit far from it. Or, stop using the object emitting the electromagnetic waves.

Check that the Bluetooth wireless technology device is not too far from the unit and that obstructions are not set between the Bluetooth wireless technology device and the unit. Set the Bluetooth wireless technology device and the unit so that the distance between them is less than about 10 m and no obstructions exist between

them.

Check that the Bluetooth ADAPTER and the ADAPTER PORT of the unit are correctly connected.

The Bluetooth wireless technology device may not be set to the communication mode supporting the Bluetooth wireless technology. Check the setting of the Bluetooth wireless technology device.

Check that pairing is correct. The pairing setting was deleted from this unit or the Bluetooth wireless technology device. Reset the pairing.

Check that the profile is correct. Use a Bluetooth wireless technology device that supports A2DP profile and AVRCP profile.

Error Messages

Message

Description

EXTRAPWR

• You cannot adjust SFC modes, tone controls (bass, treble, and bass boost),

 

MP3 Expander mode, Voice Enhancer mode when using Extra Power mode.

 

 

CANNOT

• Operation is prohibited because DVD/CD or USB isn’t selected, or

 

SHIFT+KARAOKE, SHIFT+ECHO, SHIFT+ or SHIFT+ has been pressed.

 

• Appears when DVD/CD is not selected and SHIFT+USB REC is pressed.

 

 

TRAYLOCK

• The tray lock is on. See General in Troubleshooting on page 53.

 

 

56

En

Additional information

13

Message

Description

STEREO

STEREO appears when SURROUND or AUTO/STEREO is pressed in the TUNER,

 

LINE or ADAPTER PORT input mode.

 

 

 

 

KEYLOCK

• The key lock is enabled. See Setting the Key Lock on page 52.

 

 

 

 

USB ERR

• See Important in Using the USB interface on page 31 for more on this.

 

 

 

 

HDMI ERR

• See HDMI connection above for troubleshooting tips. See also Resetting the HDMI

 

connection on page 42 if the problem persists.

 

 

 

 

EEP ERR

• Contact your Pioneer authorized service center or your dealer for servicing.

 

 

 

 

EXIT

• Appears when any prohibited signal is input or the headphones are connected

 

while the menu screen is displayed, and then the display returns to the normal

 

display.

 

 

 

 

NO MIC

• Appears when you press SHIFT+KARAOKE, SHIFT+ECHO, SHIFT+ , SHIFT+ or

 

MIC VOL +/– when no mic is inserted.

 

 

 

 

OC ERR 1

• Check whether the speaker cables are short-circuited. If the error message

OC ERR 2

continues to be displayed, contact your Pioneer authorized service center or your

 

dealer for servicing.

 

 

 

 

OVER TEMP

• Try lowering the volume. If this problem is not fixed by removing and inserting the

 

power cable, this unit may be damaged. In such an event, please contact a Pioneer-

 

authorized service center or your nearest dealer.

 

 

 

 

BT ERR

• Power consumption by Bluetooth ADAPTER is too high to supply the power.

 

Reconnect the Bluetooth ADAPTER.

 

 

 

 

TV AUDIO

• Indicator is lit for two seconds if the listening mode is changed while HDMI audio

 

mode is set for TV.

 

 

 

 

KARAOKE

• Appears when you press SURROUND, SOUND, AUTO/STEREO or MP3 EXP/

 

V.ENH when a mic is inserted.

 

 

 

 

PHONESIN

• Appears when you press SURROUND, SOUND, AUTO/STEREO or MP3 EXP/

 

V.ENH when a headphone is inserted.

 

 

 

 

 

 

 

 

Resetting the system

Use this procedure to reset all system settings to the factory default.

1With the system on, press SHIFT+SETUP.

2Use / to select INITIAL then press

ENTER.

3Use / to select ALL INIT then press

ENTER.

INIT OK is displayed.

4Press ENTER while INIT OK is blinking.1

Using the language code list

Some of the language options (see Language settings on page 36) allow you to set your preferred language from any of the 136 languages in the Language code list below.

1Select ‘Other Language’.

2Use / to select either a code letter or a code number.

3Use / to select a code letter or a code number.

See the Language code list below for a complete list of languages and codes.

Note

1 Do not operate the unit without reason or pull the power cord because the system’s power automatically turns on.

Español Nederlands Italiano Français Deutsch English

57

En

13 Additional information

Language code list

Language (Language code letter), Language code

Japanese (ja), 1001

English (en), 0514

French (fr), 0618

German (de), 0405

Italian (it), 0920

Spanish (es), 0519

Dutch (nl), 1412

Russian (ru), 1821

Chinese (zh), 2608

Korean (ko), 1115

Greek (el), 0512

Afar (aa), 0101

Abkhazian (ab), 0102

Afrikaans (af), 0106

Amharic (am), 0113

Arabic (ar), 0118

Assamese (as), 0119

Aymara (ay), 0125

Azerbaijani (az), 0126

Bashkir (ba), 0201

Byelorussian (be), 0205

Bulgarian (bg), 0207

Bihari (bh), 0208

Bislama (bi), 0209

Bengali (bn), 0214

Tibetan (bo), 0215

Breton (br), 0218

Catalan (ca), 0301

Corsican (co), 0315

Czech (cs), 0319

Welsh (cy), 0325

Danish (da), 0401

Bhutani (dz), 0426

Esperanto (eo), 0515

Estonian (et), 0520

Basque (eu), 0521

Persian (fa), 0601

Finnish (fi), 0609

Fiji (fj), 0610

Faroese (fo), 0615

Frisian (fy), 0625

Irish (ga), 0701

Scots-Gaelic (gd), 0704

Galician (gl), 0712

Guarani (gn), 0714

Gujarati (gu), 0721

Hausa (ha), 0801

Hindi (hi), 0809

Croatian (hr), 0818

Hungarian (hu), 0821

Armenian (hy), 0825

Interlingua (ia), 0901

Interlingue (ie), 0905

Inupiak (ik), 0911

Indonesian (in), 0914

Icelandic (is), 0919

Hebrew (iw), 0923

Yiddish (ji), 1009

Javanese (jw), 1023

Georgian (ka), 1101

Kazakh (kk), 1111

Greenlandic (kl), 1112

Cambodian (km), 1113

Kannada (kn), 1114

Kashmiri (ks), 1119

Kurdish (ku), 1121

Kirghiz (ky), 1125

Latin (la), 1201

Lingala (ln), 1214

Slovak (sk), 1911

Laothian (lo), 1215

Slovenian (sl), 1912

Lithuanian (lt), 1220

Samoan (sm), 1913

Latvian (lv), 1222

Shona (sn), 1914

Malagasy (mg), 1307

Somali (so), 1915

Maori (mi), 1309

Albanian (sq), 1917

Macedonian (mk), 1311

Serbian (sr), 1918

Malayalam (ml), 1312

Siswati (ss), 1919

Mongolian (mn), 1314

Sesotho (st), 1920

Moldavian (mo), 1315

Sundanese (su), 1921

Marathi (mr), 1318

Swedish (sv), 1922

Malay (ms), 1319

Swahili (sw), 1923

Maltese (mt), 1320

Tamil (ta), 2001

Burmese (my), 1325

Telugu (te), 2005

Nauru (na), 1401

Tajik (tg), 2007

Nepali (ne), 1405

Thai (th), 2008

Norwegian (no), 1415

Tigrinya (ti), 2009

Occitan (oc), 1503

Turkmen (tk), 2011

Oromo (om), 1513

Tagalog (tl), 2012

Oriya (or), 1518

Setswana (tn), 2014

Panjabi (pa), 1601

Tonga (to), 2015

Polish (pl), 1612

Turkish (tr), 2018

Pashto, Pushto (ps), 1619

Tsonga (ts), 2019

Portuguese (pt), 1620

Tatar (tt), 2020

Quechua (qu), 1721

Twi (tw), 2023

Rhaeto-Romance (rm), 1813

Ukrainian (uk), 2111

Kirundi (rn), 1814

Urdu (ur), 2118

Romanian (ro), 1815

Uzbek (uz), 2126

Kinyarwanda (rw), 1823

Vietnamese (vi), 2209

Sanskrit (sa), 1901

Volapük (vo), 2215

Sindhi (sd), 1904

Wolof (wo), 2315

Sangho (sg), 1907

Xhosa (xh), 2408

Serbo-Croatian (sh), 1908

Yoruba (yo), 2515

Sinhalese (si), 1909

Zulu (zu), 2621

Country/Area code list

Country/Area, Country/Area code, Country/Area code letter

Argentina, 0118, ar

Hong Kong, 0811, hk

Philippines, 1608, ph

Australia, 0121, au

India, 0914, in

Portugal, 1620, pt

Austria, 0120, at

Indonesia, 0904, id

Russian Federation, 1821, ru

Belgium, 0205, be

Italy, 0920, it

Singapore, 1907, sg

Brazil, 0218, br

Japan, 1016, jp

Spain, 0519, es

Canada, 0301, ca

Korea, Republic of, 1118, kr

Switzerland, 0308, ch

Chile, 0312, cl

Malaysia, 1325, my

Sweden, 1905, se

China, 0314, cn

Mexico, 1324, mx

Taiwan, 2023, tw

Denmark, 0411, dk

Netherlands, 1412, nl

Thailand, 2008, th

Finland, 0609, fi

New Zealand, 1426, nz

United Kingdom, 0702, gb

France, 0618, fr

Norway, 1415, no

United States of America, 2119, us

Germany, 0405, de

Pakistan, 1611, pk

 

58

En

Additional information

13

Specifications

• Amplifier section

RMS Power Output:

Front, Center, Surround . . . 60 W per channel (1 kHz, 10 % T.H.D., 4 Ω)

Subwoofer . . . 60 W (100 Hz, 10 % T.H.D., 4 Ω)

Disc section

Type. . . . . . . .DVD system, Video CD/Super VCD system and Compact Disc digital audio system

FM tuner section

Frequency range . . . . . . . . 87.5 MHz to 108 MHz Antenna . . . . . . . . . . . . . . . . . . 75 Ω, unbalanced

• AM tuner section

Frequency range:

Saudi Arabia, Israel, South Africa, other middle eastern contries and duty free models

. . . . . . . . . . . . . . . . . . . . . . . . 531 kHz to 1602 kHz All other models

With 9 kHz step . . . . . . . . 531 kHz to 1602 kHz With 10 kHz step . . . . . . . 530 kHz to 1700 kHz Antenna . . . . . . . . . . . . . . . . . . . . . Loop antenna

• Miscellaneous

Power requirements:

Singapore, Indonesia, Hong Kong, Malaysia, Philippines models

. . . . . . . . . . . . AC 220 V to 240 V, 50 Hz/60 Hz All other models

. . . . . . . . . . . . AC 110 V to 240 V, 50 Hz/60 Hz Power consumption . . . . . . . . . . . . . . . . . . .55 W Power consumption in standby:

For HTZ180/181DVD . . . . . . . . . . . . . . . 0.48 W

Others

KURO LINK ON . . . . . . . . . . . . . . . . . 0.73 W KURO LINK OFF. . . . . . . . . . . . . . . . . 0.48 W

Dimensions

. . . . . . . . 420 mm (W) x 62 mm (H) x 331 mm (D) Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.8 kg

Accessories (DVD/CD receiver)

Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . 1 AA/R6 dry cell batteries

(to confirm system operation) . . . . . . . . . . . . . . 2 Video cable (yellow plugs) . . . . . . . . . . . . . . . . . 1 AM loop antenna . . . . . . . . . . . . . . . . . . . . . . . . . 1 FM antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Power cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Setup Guide

Operating instructions (This document)

S-DV180 Speaker system

Front speakers

Enclosure . . . . . . . . . Closed-box bookshelf type (magnetically shielded)

System . . . . . . . . . . . . . . . . . 7.7 cm 1-way system Speakers . . . . . . . . . . . . . . . . . . 7.7 cm cone type Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Ω Frequency range . . . . . . . . . . . . 90 Hz to 20 kHz Maximum input power . . . . . . . . . . . . . . . . . 60 W Dimensions

. . . . . . 105 mm (W) x 115 mm (H) x 114 mm (D) Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.6 kg

Center speaker

Enclosure . . . . . . . . . Closed-box bookshelf type (magnetically shielded)

System . . . . . . . . . . . . . . . . . 7.7 cm 1-way system Speakers . . . . . . . . . . . . . . . . . . 7.7 cm cone type Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Ω Frequency range . . . . . . . . . . . . 90 Hz to 20 kHz Maximum input power . . . . . . . . . . . . . . . . . 60 W Dimensions

. . . . . . 115 mm (W) x 105 mm (H) x 114 mm (D) Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.6 kg

Surround speaker

Enclosure . . . . . . . . . Closed-box bookshelf type (magnetically shielded)

System . . . . . . . . . . . . . . . . . 7.7 cm 1-way system Speakers . . . . . . . . . . . . . . . . . . 7.7 cm cone type Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Ω Frequency range . . . . . . . . . . . . 98 Hz to 20 kHz Maximum input power . . . . . . . . . . . . . . . . . 60 W Dimensions

. . . . . . 105 mm (W) x 118 mm (H) x 114 mm (D) Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.6 kg

Subwoofer

Enclosure . . . . . . Bass-reflex floorstanding type System . . . . . . . . . . . . . . . . . 16 cm 1-way system Speaker . . . . . . . . . . . . . . . . . . . .16 cm cone type Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Ω Frequency range . . . . . . . . . . . . . 28 Hz to 1 kHz Maximum Input Power. . . . . . . . . . . . . . . . . 60 W Dimensions

. . . . . . 190 mm (W) x 360 mm (H) x 317 mm (D) Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8 kg

Accessories

Non-skid pads (small) . . . . . . . . . . . . . . . . . . . .12 Non-skid pads (large) . . . . . . . . . . . . . . . . . . . . . 4 Mounting brackets . . . . . . . . . . . . . . . . . . . . . . . 4 Screws (for mounting brackets) . . . . . . . . . . . . 4

Español Nederlands Italiano Français Deutsch English

59

En

13 Additional information

S-DV585 Speaker system

Front/surround speakers

Enclosure. . . . . . . . Closed-box bookshelf type

. . . . . . . . . . . . . . . . . . .(magnetically shielded) System . . . . . . . . . . . . . . . 6.6 cm 1-way system Speakers . . . . . . . . . . . . . . . . 6.6 cm cone type Impedance . . . . . . . . . . . . . . . . . . . . . . . . . 4 Ω Frequency range . . . . . . . . . . 82 Hz to 20 kHz Maximum input power . . . . . . . . . . . . . . 100 W Dimensions

. . . . . . . 96 mm (W) x 96 mm (H) x 96 mm (D) Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 kg

Center speaker

Enclosure. . . . . . . . Closed-box bookshelf type (magnetically shielded)

System . . . . . . . . . . . . . . . 6.6 cm 1-way system Speakers . . . . . . . . . . . . . . . . 6.6 cm cone type Impedance . . . . . . . . . . . . . . . . . . . . . . . . . 8 Ω Frequency range . . . . . . . . . . 82 Hz to 20 kHz Maximum input power . . . . . . . . . . . . . . . 50 W Dimensions

. . . . . . . 96 mm (W) x 96 mm (H) x 96 mm (D) Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 kg

Subwoofer

Enclosure. . . . . Bass-reflex floorstanding type System . . . . . . . . . . . . . . . 16 cm 1-way system Speaker . . . . . . . . . . . . . . . . . 16 cm cone type Impedance . . . . . . . . . . . . . . . . . . . . . . . . . 4 Ω Frequency range . . . . . . . . . . . 34 Hz to 1 kHz Maximum Input Power. . . . . . . . . . . . . . 100 W Dimensions

. . . . 230 mm (W) x 380 mm (H) x 360 mm (D) Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.4 kg

Accessories

Speaker cables . . . . . . . . . . . . . . . . . . . . . . . . 5 Brackets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Mounting brackets . . . . . . . . . . . . . . . . . . . . . 6 Screws (common use for brackets and mounting brackets) . . . . . . . . . . . . . . . . . . . . 8 Non-skid pads (small) . . . . . . . . . . . . . . . . . 18 Non-skid pads (large) . . . . . . . . . . . . . . . . . . . 4

S-DV280T Speaker system

Front speakers

Enclosure . . . . Closed-box floorstanding type

. . . . . . . . . . . . . . . . . . .(magnetically shielded) System . . . . . . . . . . . . . . . . . . . . 2-way system Speakers:

Woofer . . . . . . . . . . . . . . . . . 7.7 cm cone type 60 Tweeter . . . . . . . . . . .2.6 cm semi-dome type

Impedance . . . . . . . . . . . . . . . . . . . . . . . . 4 Ω Frequency range . . . . . . . . . . 62 Hz to 20 kHz Maximum input power . . . . . . . . . . . . . . .60 W Dimensions

. . . .260 mm (W) x 1097 mm (H) x 260 mm (D) Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8 kg

Center speaker

Enclosure . . . . . . .

Closed-box bookshelf type

. . . . . . . . . . . . . . . . .

. . (magnetically shielded)

System . . . . . . . . . .

. . . .

7.7 cm 1-way system

Speaker . . . . . . . . .

. . . .

. . . 7.7 cm cone type

Impedance . . . . . .

. . . . .

. . . . . . . . . . . . . 4 Ω

Frequency range . .

. . . . .

. . . 72 Hz to 20 kHz

Maximum input power . .

. . . . . . . . . . . . .60 W

Dimensions

 

 

. . . . . .220 mm (W) x 90 mm (H) x 100 mm (D)

Weight . . . . . . . . . .

. . . . .

. . . . . . . . . . . 0.7 kg

Surround speakers

Enclosure . . . . . . .

Closed-box bookshelf type

. . . . . . . . . . . . . . . . .

. . (magnetically shielded)

System . . . . . . . . . .

. . . .

7.7 cm 1-way system

Speakers. . . . . . . . .

. . . .

. . . 7.7 cm cone type

Impedance . . . . . .

. . . . .

. . . . . . . . . . . . . . 4 Ω

Frequency range . .

. . . . .

. . . . 84 Hz to 20 kHz

Maximum input power . .

. . . . . . . . . . . .100 W

Dimensions

 

 

. . . . .100 mm (W) x 100 mm (H) x 100 mm (D)

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . .

0.5 kg

Accessories

Speaker cables. . . . . . . . . . . . . . . . . . . . . . . . 5 Non-skid pads (small) . . . . . . . . . . . . . . . . . . 8 Non-skid pads (large) . . . . . . . . . . . . . . . . . . 8 Speaker stand bases . . . . . . . . . . . . . . . . . . 2 Screws (for bases) . . . . . . . . . . . . . . . . . . . . 6

S-DV282T Speaker system

Front/surround speakers

Same as S-DV280T Front speakers (see above)

Center speaker

Same as S-DV280T Center speaker (see above)

Accessories

Speaker cables. . . . . . . . . . . . . . . . . . . . . . . . . . 5 Non-skid pads (large) . . . . . . . . . . . . . . . . . . . 16 Speaker stand bases . . . . . . . . . . . . . . . . . . . . 4 Screws (for bases) . . . . . . . . . . . . . . . . . . . . . . 12

En

Additional information

13

S-DV5SW Speaker system

Subwoofer

Enclosure . . . . . . .Bass-reflex floorstanding type System . . . . . . . . . . . . . . . . . 16 cm 1-way system Speaker. . . . . . . . . . . . . . . . . . . . 16 cm cone type Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Ω Frequency range . . . . . . . . . . . . . . 34 Hz to 1 kHz Maximum Input Power . . . . . . . . . . . . . . . .100 W Dimensions

. . . . . . . 230 mm (W) x 380 mm (H) x 360 mm (D) Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.4 kg

Accessories

Non-skid pads (large) . . . . . . . . . . . . . . . . . . . . . 4

Note

Specifications and design subject to possible modification without notice, due to improvements.

This product includes FontAvenue® fonts licenced by NEC Corporation. FontAvenue is a registered trademark of NEC Corporation.

This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized

by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

DRM (digital rights management) copy protection is a technology designed to prevent unauthorized copying by restricting playback, etc. of compressed audio files on devices other than the PC (or other recording equipment) used to record it. For detailed information, please see the instruction manuals or help files that came with your PC and/or software.

Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Dolby Laboratories.

Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS and DTS Digital Surround are registered trademarks and the DTS logos and Symbol are trademarks of DTS, Inc. © 1996-2008 DTS, Inc. All Rights Reserved.

Published by Pioneer Corporation. Copyright © 2009 Pioneer Corporation. All rights reserved.

Español Nederlands Italiano Français Deutsch English

61

En

D3-4-2-1-1_A1_Zhtw

ĬĶġ ġ ġĬĴĶġ

ĬĵIJġ ġ ġĬĺĶġ

ĹĶġĦœʼn

 

 

D3-4-2-1-7c*_A1_Zhtw

 

 

 

 

 

 

考之用。

01

. . . . . . . . . . . . . . . . . . . . . 6 5 /4 . . . . . . . . . . . . . . . . . . 6 3 /2 . . . . . . . . . . . . . . . . . . 6

. . . . . . . . . . . . . . . . . . . . . . . . . . . 6

. . . . . . . . . . . . . . . 6

HTZ280DVD/HTZ280DVD-AP/HTZ282DVD/ HTZ282DVD-AP . . . . . . . . . . . . 6

HTZ181DVD . . . 7

. . . . . . . . . . . . . . . . . . . . 7

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

HTZ180/181DVD

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8. . . . . . . . . . . . . . 8

02

. . . . . . . . . . . . . . . . . . . . . . . . . 9

03

 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14

. . . . . . . . . . . . . . . . . . . . .

15

. . . . . . . . . . . . . . . . . . . . . . . . .

16

04

. . . . . . . . . . . . . . . . . . . . . . 17

. . . . . . . . . . . . . . . . . . . . . . . 17OSD . . . . . . . . . . . . . 18

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 18. . . . . . . . . . . . . . . . . . . . . . . 19

. . . . . . . . . . . . . . 19 DVD-Video . . . . . . . . . . . . . . . . . 19 VCD/ VCD PBC . . . . . . . . . . . . . 19

. . . . . . . . . . . . . . . . . . . . . . . . . . 20FM . . . . . . . . . . . . . . . . . . . 20AM . . . . . . . . . . . . . . . . . . . 20

. . . . . . . . . . . . . . . . . . . . . . . . . . 20. . . . . . . . . . . . . . . . . . . . . . . 21. . . . . . . . . . . . . . . . . . . . . . . . 21. . . . . . . . . . . . . . . . . . . . . . 21

05

. . . . . . . . . . . . . . . . . . . . . . . . 22. . . . . . . . . . . . . . . . . . . . . . . . 22. . . . . . . . . . . . . . . . . . . . . . . . 22. . . . . . . . . . . . . . . . . . . . . . 23. . . . . . . . . . . . . . . . . . . . . . . . 23. . . . . . . . . . . . . . . . . . . . . . . . . . 23

. . . . . . . . . . . . . . . . . . . . . . 23SFC . . . . . . . . . . . . . . . . . . . . . . . . 23

. . . . . . . . . . . . . . . . . . . . . . . . 24MP3 . . . . . . . . . . . . . . . . . . . . . 24

. . . . . . . . . . . . . . . . . . . 24

. . . . . . . . . . 24

06

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 25. . . . . . . . . . . . . . . . . . . . . . . . . . 25

. . . . . . . . . . . . . . . . . . . . . . 25JPEG . . . . . . . . . . . . . . . . . . . 25

DVD VCD/

VCD . . . . . . . . . . . . . . . . . . . . . . . 26

Windows Media™ Audio (WMA) MP3 MPEG-4 AAC DivX /WMV JPEG . . . . . 27

. . . . . . . . . . . . . . . . . . . . . . . . 27. . . . . . . . . . . . . . . . . . . . . . . 27. . . . . . . . . . . . . . . . . . . . . . . 28. . . . . . . . . . . . . . . . 28. . . . . . . . . . . . . . . . . 28. . . . . . . . . . . . . . . . . . . . . 28. . . . . . . . . . . . . . . . . . . . . 28. . . . . . . . . . . . . . . . . . . . . 29

. . . . . . . . . 29

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 29. . . . . . . . . . . . . . . . . . . . . . . . . . . . 30. . . . . . . . . . . . . . . 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . 30. . . . . . . . . . . . . . . . . . . . . . . . 30. . . . . . . . . . . . . . . . . . . . . . . . 30

4

Zhtw

07 USB

USB . . . . . . . . . . . . . . . . . . . . . . . . 31

USB CD . . . . . . . 31

. . . . . . . . . . . . . . . . . . . . . . . 31. . . . . . . . . . . . . . . . . . . . . . . 32

08 OK

OK . . . . . . . . . . . . . . . . . . . . . . . . 33. . . . . . . . . . . . . . . . . . . . . . . 33. . . . . . . . . . . . . . . . . . . . . . . 33

09

. . . . . . . . . . . . . . . . . . . . . 34DRC . . . . . . . . . . . . 34

. . . . . . . . . . . . . . . . . . . . . 34

10

. . . . . . . . . . . . . . . . . 35. . . . . . . . . . . . . . . . . . . . . . . 35. . . . . . . . . . . . . . . . . . . . . . . . . . 36. . . . . . . . . . . . . . . . . . . . . . . . 37. . . . . . . . . . . . . . . . . . . . . . . . . . 37. . . . . . . . . . . . . . . . . . . . . . . . . . 37

. . . . . . . . . . . . . . . . . . . . . . . . . . . 37DivX® VOD . . . . . . . . . . . . . . . . 38. . . . . . . . . . . . . . . . . . . . . . . . . 39

11

. . . . . . . . . . . . . . . . . . . . . 40. . . . . . . . . . . . . . . . . 41

. . . . . . . . . . . . . . . . . . . 41HDMI . . . . . . . . . . . . . . . . . . . . . . 41HDMI . . . . . . . . . . . . . . . . 41HDMI . . . . . . . . . . . . . . . . . 42HDMI . . . . . . . . . . . . . . . . . . . . . . . . . 42

. . . . . . . . . . . . . . . . . . . . . . . . 42

Bluetooth® . . . 42

. . . . . . . . . . . . . . . . . . . . . . . 42

. . . . . . . . . . . . . . . . . . . . . . . . . 43Bluetooth . . . . . . . . . . 43

Bluetooth Bluetooth

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Bluetooth. . . . . . . . . . . . . . . . . . . . . . . . . . . 44. . . . . . . . . . . . . . . . . . . . . . . . . . . 44

12 KURO LINK

KURO LINK . . . . . . . . . . . . . . . . . . . . . . 45 KURO LINK . . . . . . . . . . . . . . . . . . . . . . 45KURO LINK . . . . . . . . . . . . . . . . . 45

. . . . . . . . . . . . . . . . . . . . . . . 46. . . . . . . . . . . . . . . . . . . . . . . 46. . . . . . . . . . . . . . . . . . 46. . . . . . . . . . . . . . . . . . 46

13

. . . . . . . . . . . . . . 47

. . . . . . . . . . . . . . . . . . . . 47

DVD+R/DVD+RW . . . . . . . . . . 48

DivX . . . . . . . . . . . . . . . . . . . . . . . . . . 48WMV . . . . . . . . . . . . . . . . . . . . . . . . . 49MPEG-4 AAC. . . . . . . . . . . . . . . . . . . 49WMA . . . . . . . . . . . . . . . . . . . . . . . . . 49

. . . . . . . . . . . . . . . . . . . . . 49 DVD Video . . . . . . . . . . . . . . . . . 50

. . . . . . . . . . . . . . . . . . . . . . . . . . 50. . . . . . . . . . . . . . . . . . . . . . . . . . . 50. . . . . . . . . . . . . . . . . . . . . . . 50. . . . . . . . . . . . . . . . . . . . . . . 50. . . . . . . . . . . . . . . . . . . . . . . 50

. . . . . . . . . . . . . . . . . . . 51. . . . . . . . . . . . . . . . . . . . 51. . . . . . . . . . . . . . . . . . . . . 51. . . . . . . . . . . . . . . . . . . . . . . . . 51. . . . . . . . . . . . . . . . . . . . . . . . . 52

. . . . . . . . . . . . . . . . . . . . . . . 52Key Lock . . . . . . . . . . . . . . . 52

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

. . . . . . . . . . . . . . . . . . . . . . . . . . . 53 DVD/CD/VCD . . . . . . . . . . . . . . . . . 54

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 USB . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 HDMI . . . . . . . . . . . . . . . . . . . . . . . . . 55 Bluetooth . . . . . . . . . . . . . . . . . . . . . . 56

. . . . . . . . . . . . . . . . . . . . . . . . . . . 56. . . . . . . . . . . . . . . . . . . . . . . . . 57. . . . . . . . . . . . . . . . . . . . . 57. . . . . . . . . . . . . . . . . . . . . . . . . 58. . . . . . . . . . . . . . . . . . . 58. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

English

Español

5

Zhtw

01

1

5 /4

5.1

3 /2

3 4

HTZ280DVD/HTZ280DVD-AP/ HTZ282DVD/HTZ282DVD-AP

5 3

向等腰三角形的底座的方向。

紋可能會損壞。使用中等尺寸的手動螺絲起 子組裝。

揚聲器上。

致本機翻覆或摔落。

或導致人員受傷。請注意小孩。

確定已牢牢固定揚聲器。

6

Zhtw

子直接將揚聲器掛在牆壁上。一律使用纜線 保持揚聲器的穩定。

掉落並造成人員受傷的區域。

HTZ181DVD

1

4 /3

4 Ļ

 

 

 

 

 

3 Ļ

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

01

2

English

Español

 

 

 

 

 

Español

 

 

 

 

 

 

 

HTZ180DVD

 

HTZ181DVD

 

HTZ280DVD/280DVD-AP

 

HTZ282DVD/

 

HTZ282DVD-AP

聲器掉落。請確定您要安裝的那面牆的強度 足以支援這些揚聲器。請勿安裝在膠合板或 軟質的牆壁上。

1 60°

7

Zhtw

01

業人員的意見。

5 mm

10 mm

5 mm 7 mm

HTZ180/181DVD

將隨機附贈的螺絲上緊固定。

5

壞。

策安全。

15 30

亦不應太過接近重低音。

HTZ180DVD HTZ280/ 282DVD HTZ282DVD

HTZ280DVD

8

Zhtw

2

1.8 m 2.7 m

HTZ180DVD

 

 

 

 

 

 

COMPONENT

PR

A

 

 

FM

 

LINE 1

R

 

L

CENTER

VIDEO

 

N

 

 

 

 

FRONT

 

T

 

 

 

 

 

 

 

 

 

 

 

E

 

 

 

 

L

 

 

 

 

VIDEO(TV)

PB

N

 

FM

 

 

 

 

 

 

 

 

N

 

 

 

 

 

 

 

 

 

 

A

AM LOOP

UNBAL 75

Ω

AC IN

R

 

 

 

SUB

 

 

 

 

HDMI OUT

 

 

R

 

L

 

 

 

 

 

 

 

 

SURROUND

WOOFER

 

 

 

 

 

 

ANALOG AUDIO IN

SPEAKERS (4 Ω )

VIDEO OUT

AM

02

English

Español

座上。

1 AM

a

b

c

Español

不擔負任何責任。

c.b

9

Zhtw

02

2AM FM 1

a.AM

AM AM2

3 1

+–

(–)(+)

HTZ180DVD

 

2

3 a

 

c

b. FM 3 FM

a.

 

 

 

 

 

3-1

 

 

 

 

ġ

1

20 FM 42

42

2

AM 3 FM

10

Zhtw

 

02

b.

聲器線。

HTZ181DVD

a. Y

English

c.

FRONT SURROUND

確固定於前置揚聲器之上。

來完成3

Y

4 3 2b

b.

3-2

Español

Español

11

Zhtw

02

拔離。

牢連接至端子。連接不良可能造成雜訊和聲 音中斷。

擴大器。

本機的影像無法在您的電視機上正常顯示。

61

AC

AC IN

AC

1

12

Zhtw

3

1

2

3

4

5

6

STANDBY/ON

OPEN/CLOSE

FUNCTION

 

 

VOLUME

 

 

 

7

 

8

 

9

 

MAIN MIC SUB

PHONES

USB

03

1 2 3 4

PRGSVE SOUND DTS F.SURR.

2D

2PL

English

5 6

RPT -1

kHz PGM

MHz RDM

12 11

10

9

8

7

Español

 

1 22

DTS DTS 2PL II

2Dolby Pro Logic II 2D

2 PRGSVE 41

亮起。

 

 

 

 

 

 

 

3 SOUND 23

 

 

 

 

 

 

 

 

 

 

10

11

12

SFC

1

STANDBY/ON 17 32 43 50

MP3

52 54

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

OPEN/CLOSE 18 32 53

4 F.SURR. 23

 

3

 

 

 

 

 

 

4

 

 

 

 

 

 

 

 

 

 

 

5 RPT RPT-1 28

 

5

 

 

 

 

 

 

 

 

 

 

RPT RPT-1

6

VOLUME +/– 19

 

 

 

 

 

 

7

18

 

 

 

 

6 PGM 27 29

 

 

 

 

 

 

8

15

 

 

 

 

 

 

 

 

7 20

 

9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10

USB 31

 

 

 

 

FM

FM

11

MIC 33

 

 

 

 

 

 

 

 

 

 

8 RDM 28

 

12

PHONES 23

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Español

13

Zhtw

03

9 kHz/MHz 20

kHzAM MHz FM

11 21

HTZ280/282DVD-AP

STANDBY

 

TUNER

 

 

/ON

DVD/CD

(FM/AM)

OPEN/CLOSE

11

1

 

 

PLAYLIST

ADAPTERPORT

USB

LINE

 

2

 

 

1

 

1

2

3

2

12

USB REC

AUDIO

SUBTITLE

 

 

4

5

6

3

 

3

ANGLE

ZOOM

 

 

7

8

9

 

13

CLEAR

SLEEP

DISPLAY

MIC VOL

0

 

 

 

 

TOP MENU

TUNE

MENU

 

4

5

6

7

8

14

SETUP

PRESET

ENTER

PRESET

HOME

 

 

MENU

 

RETURN

 

TUNE

15

AUTO/

MP3 EXP/

STEREO

SURROUND SOUND

V.ENH

9

10

 

TV CONTROL

 

CLASS

INPUT

CHANNEL

VOLUME

T.EDIT

MUTE

 

 

 

SHIFT

 

VOLUME

 

16

17

18

1 STANDBY/ON 17 32 43 50 52 54

2 1

3 CLEAR DISPLAY SLEEP DVD

CLEAR

DISPLAY 30

SHIFT+SLEEP 21

SHIFT+USB REC 31

SHIFT+AUDIO 30

1 HTZ280/282DVD-AP

14

Zhtw

 

03

SHIFT+SUBTITLE 30

SHIFT+ANGLE 30

SHIFT+ZOOM 30

4TOP MENU 19 30

SHIFT+SETUP 17 20 41 43 44 45 51 52 57

5SHIFT+KARAOKE 33

SHIFT+ECHO 33

SHIFT+ / SHIFT+ 33

ENTER

TUNE 20

PRESET 20

6HOME MENU

AUTO/STEREO 22 23

SURROUND 22 23

SOUND 23 24

MP3 EXP/V.ENH 24

819 25

9TV CONTROL

1

10SHIFT

11OPEN/CLOSE 18 32 53

12PLAYLIST 27

13MIC VOL +/– 33

14MENU 19 26 30

15RETURN

CLASS 21

SHIFT+T.EDIT 20

17MUTE

18VOLUME +/– 18

2 AA/R6

險發生。請遵守下列事項

牌而定。請勿混用不同品牌的電池。

貴國或地區的環境公共指令規則。

English

Español

Español

1 1 CLEAR 2 TV CONTROL

15

Zhtw

盡。

7 m30°

用。

可能造成其他裝置的運作異常。

池。

16

Zhtw

4

下次開啟系統電源時會再次顯示相同內容。

1STANDBY/ON

WELCOME

2SELECT SPEAKER LAYOUT10

3/

5

3

請參閱

5 SPOT 5.1

4 SPOT HTZ181DVD 5

3 SPOT

2 SPOT HTZ181DVD 3

4 ENTER 1

2

1SHIFT+SETUP

2/ SOUNDSET

ENTER

3/ CH LEVEL

ENTER

4/ TESTTONE

ENTER

下啟動中的揚聲器

L

C

R

SR

SL

SW 3

04

English

Español

Español

1SHIFT+SETUP / SYS SET / LAYOUT

2DVD/CD

SHIFT+SETUP / SOUNDSET ENTER /CH LEVEL ENTER / / ENTER

17

Zhtw

04

5VOLUME +/–1

6/

±10 dB

7 ENTER

DVD CD VCD/ VCD DivX/WMV WMA/MP3/MPEG-4 AAC

會在第6

DVD DVDVideo DVD-R DVD-RW

OSD

OSD

ENTER2

ENTER

HOME OSD

MENU

ENTER

RETURN

OSD

1

視機打開並確定設置的是正確的視頻輸入。

2 OPEN/CLOSE

DVD

3

DVD VCD/ VCD19 DVD-Video

VCD/ VCD PBCJPEG

25

JPEG

DivX /WMVMP3OSD DivX / WMV DivX/WMVMP3/WMA/JPEG/MPEG-4

AAC

151 TESTTONE+

18

Zhtw

DualDisc DVD/CD47

4

VOLUME +/–

控制。1 6

RESUME

LAST MEM

螢幕上顯示RESUME

按下ENTER

DVD CD/VCD/

VCD

VR DVD-R/-RWDVD-Video CD/VCD/

VCD

RESUME

DVD VCD/ VCD 2LAST MEM

顯示RESUME

DVD-Video

DVD-Video

DVD-Video MENUTOP MENU

TOP MENU DVD

MENU DVD

ENTER

RETURN

ENTER

VCD/ VCD PBC

VCD/ VCD PBC

1DVD

2

DVD-Video VR DVD-R/-RW

04

English

Español

Español

19

Zhtw

04

PBC

PBC VCD/ VCD

RETURN PBC

ENTER

1FM

SHIFT+SETUP

2/ TUNERSET

ENTER

3/ FM MODE

ENTER

4/ FM MONO

ENTER

FM AUTO

FM AM

1TUNERAM FM

TUNE

TUNE

TUNE

FM

FM

20

AM

AM AM

1AM

SHIFT+SETUP

2/ TUNERSET

ENTER

3/ NOISECUT

ENTER

4/

ENTER

1 2

30A B C 10

1 AM FM

FM

2SHIFT+T.EDIT

3CLASSPRESET

Zhtw

4 ENTER

ENTER

1TUNER

2CLASS A B C

3PRESET

40

USB USB31 USB

HTZ280/282DVD-APBluetooth Bluetooth

42Bluetooth®

1 已經開機。

2LINE

1

SHIFT+SLEEP

ENTER

SLP ON

SLP OFF

SLP ON SHIFT+SLEEP

12

S L P - - - --

04

English

Español

Español

1

21

Zhtw

5

HDMI4133 56

6

5 /4

5

3 /2

323

的通道。

AUTO/STEREO AUTO1

 

5 SPOT

3 SPOT

4 SPOT

2 SPOT

 

 

 

 

 

STEREO

STEREO

 

STANDARD

F.SURR

5 /4

2

Dolby Pro Logic

SURROUND 1

STANDARD

MOVIE (Dolby Pro Logic II Movie Pro Logic II 5.1

1 Dolby Digital DTS

2 DVD/CD USB

22

Zhtw

MUSIC (Dolby Pro Logic II MusicPro Logic II 5.1

DOLBY PL (Dolby Pro Logic

4.1

DVD/CD USB 6

3 /2HTZ181DVD

SURROUND

F.SURR

EXTRAPWR

HTZ180DVD

HTZ181DVD

3

1

AUTO/STEREOSTEREO

STEREO1

1SOUND

2/ BASS/TRE

ENTER

3/ BASS TREBLE

4/ ENTER

–6dB +6dB

SFC

SFC

1SOUND

2/ SFC MODE

ENTER

3/ ENTER SFC

OFF LIVE HALL POP ROCK DRAMAACTION

05

English

Español

Español

23

Zhtw

05

的低音音量。

1SOUND

2/ BASSMODE

ENTER

3/ ENTER

OFF MUSIC CINEMA

MP3

MP3 WMA MPEG-4 AAC

MP3 EXP/V.ENH MP3 EXP 1

MP3 EXP/V.ENH VOICE E 2

音」模式啟用下列針對電影和音樂的原音最佳 真實體驗的先鋒獨家音頻技術而設計。

機的功能。3

對長時間聆聽而最佳化的播放特性。

1SHIFT+SETUP / SOUNDSET ENTER

2/ S.FIELD

ENTER

3/ ENTER

EFFECT

DIRECT

1SFC

2SFC

HTZ180/181DVD

24

Zhtw

6

功能仍可適用於DVD VCD/

VCD CD DivX /WMV WMA/ MP3/MPEG-4 AAC/JPEG

DVD

VCD/ VCD PBC

的播放。

1

2

DVD VCD/

VCD DivX /WMV DVD

06

 

 

 

 

 

1

 

 

English

 

2

/ /

 

 

 

 

 

 

 

 

2

 

 

Español

 

 

 

 

 

 

 

 

 

 

DVDVCD/ VCD DivX /WMV

2/ /

2

JPEG

JPEG

Español

 

3

 

WMA/MP3/MPEG-4

AAC

 

 

 

/ /

 

 

 

 

 

1 DivX /WMV

2DVD

PBC VCD/ VCD WMA/MP3/MPEG-4 AAC

3

299 648

25

Zhtw

06

/ / /

SHIFT+ZOOM

MENU

DVD

VCD/ VCD

DVD VCD/VCD

1 HOME MENUDisc Navigator

Disc Navigator

2

Disc Navigator

Title

Chapter

Title DVD-Video

Chapter DVD-Video

Track VCD/ VCD

Time VCD/ VCD

Original: Title VR

DVD-R/-RW

Playlist: Title VR

DVD-R/-RW

Original: Time

Playlist: Time

/

3

01

02

03

04

05

06

Disc Navigator: Title 0149: --

/ / / ENTER

按下ENTER

26

Zhtw

Windows MediaAudio (WMA) MP3 MPEG-4 AAC DivX /WMV JPEG

或資料夾。

1HOME MENU

Disc Navigator

00:00/ 00:00

0kbps

Folder1

Folder2

Folder3

Folder4

2 / / / ENTER

/ 1

ENTER

JPEG

00:00/ 00:00

0kbps

Folder2

File1

File2

File3

File4

File5

3 DivX /WMVJPEG ENTER

WMA/MP3/MPEG-4 AACJPEG

放幻燈片秀的JPEG

JPEG

WMA MP3 MPEG-4 AAC JPEG

302

1HOME MENUDisc Navigator

導向」功能瀏覽Windows Media™ Audio (WMA) MP3 MPEG-4 AAC DivX / WMV JPEG

3PLAYLIST 1 2 3

42 3

WMA/MP3/MPEG-4 AAC DivX /WMV

JPEG

播放完為止。

1.. ENTER

06

English

Español

Español

27

Zhtw

06

 

4 B(End Point)

ENTER

 

ENTER

 

 

PLAYLIST 1 2 3

5 Off

JPEG

 

 

 

 

 

 

 

PLAYLIST 1 2 3

 

 

 

 

29

PGM

 

 

 

 

1 HOME MENU

NO LIST

 

Play Mode

 

 

JPEG

 

 

 

 

2 Repeat

 

 

 

 

 

1

 

 

 

Program

1

 

 

Repeat

 

Repeat Off

 

 

 

 

 

2

Disc Navigator

 

 

 

 

DVD Title Repeat

CLEAR

 

Chapter Repeat

 

 

 

 

 

 

 

 

 

 

 

CD VCD/ VCD Disc

 

 

 

 

Repeat Track Repeat

A-B CD

 

 

 

 

VCD/ VCD DVD

 

 

 

DivX /WMV Title

A B

 

 

Repeat Repeat

 

 

 

 

 

 

1 HOME MENU

 

Off

Play Mode

 

 

 

 

 

 

 

 

Play Mode

2A-B Repeat A-B

3A(Start Point)

ENTER

DVD-Video CD VCD/ VCD 2

1 HOME MENU

Play Mode

1 WMA/MP3/MPEG-4 AAC

2

VR DVD-R/-RW WMA/MP3/MPEG-4 AAC DivX /WMV

DVD

28

Zhtw

2Random

DVD Random TitleRandom Chapter

CD VCD/ VCD OnOff

單選項中選取了Random Off

06

4 3

 

English

24

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CLEAR

 

 

 

5

 

 

Español

 

 

 

 

 

 

HOME

 

 

MENU

 

 

的播放順序程序。1

1HOME MENUPlay Mode

2Program Create/Edit

3 / / / ENTER

DVD

CD VCD/ VCD

ENTER

外的其他選項。

Playback Start

Playback Stop

Program Delete

DVD CD VCD/ VCDDivX /WMV

1 HOME MENU Play Mode

1 VR DVD-R/-RW WMA/MP3/MPEG-4 AAC DivX /WMV DVD

Español

29

Zhtw

06

2Search Mode

4 時間。

DVD/DivX

/WMV CD/VCD/ VCD

4 5 0 0451 20 308 0 3 0

5 ENTER

DVD DivX1

SHIFT+SUBTITLE

36

DivX 48

DivX

36

DVD DivX

/WMV VCD/ VCD JPEG

1SHIFT+ZOOM2 x 4 x

2/ / /

大區域。4

DVD

37

SHIFT+ANGLE

顯示在屏幕上。

 

 

DISPLAY

2

 

3

DISPLAY

 

 

VCD/ VCD

 

 

 

SHIFT+AUDIO

 

 

 

1 TOP MENU MENU

2VCD

3TOP MENU MENU

4DVD VCD/ VCD DivX /WMV JPEG

SHIFT+ZOOM

30

Zhtw

USB

7

USB

USB

USB1 DivX /WMV/JPEG

USB 2

1USB

2USB

USB

USB

USB

A

USB

3

USB JPEG

25

JPEG

面板顯示幕上顯示USB DATA

07

 

 

 

 

 

 

 

 

English

 

 

 

 

 

 

USB ERR

 

 

 

USB

 

 

 

 

 

 

 

 

 

 

 

 

Español

USB

 

 

 

 

 

 

DVD/CD

 

 

 

 

USB

 

 

 

 

AC

 

 

 

 

USB

 

 

 

 

USB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

USB CD

 

 

Español

 

 

 

 

 

 

 

USB USB

 

 

 

 

CD

 

 

 

 

 

 

 

 

 

1 CD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1 DivX /WMV/WMA/MP3/MPEG-4 AAC

2 USB FAT16/32 MP3USB

USB

USB

USB

31

Zhtw

07 USB

2 SHIFT+USB REC

CD -> USB Rec CD -> USB

CD –> USB Rec

 

 

 

Track 1–13

 

Select Track

 

Track01

01:43

Bitrate

128kbps

Track02

03:17

 

 

 

Track03

04:18

 

 

 

Track04

04:59

 

 

 

Track05

04:20

Start

 

 

Track06

04:38

Selected Track

13

Track07

04:40

Total Time

055:07

Track08

04:11

 

 

 

 

 

3 ENTER

1

CD –> USB Rec

Track 1–13

Track Progress

 

 

Track01

01:43

 

 

 

 

 

Track02

03:17

Total Progress

 

 

Track03

04:18

 

 

 

 

 

Track04

04:59

 

 

 

 

 

Track05

04:20

 

 

 

 

 

 

 

Cancel

 

 

Track06

04:38

Selected Track

13

 

Track07

04:40

Total Time

055:07

 

Track08

04:11

 

 

 

 

 

 

 

1CD

2HOME MENU

CD -> USB Rec CD -> USB

CD

CD -> USB Rec CD -> USB

CD – > USB Rec

3 / / / ENTER

CD –> USB Rec

 

 

 

 

 

Track 1–13

 

Select Track

Individual

Track01

01:43

Bitrate

Select All

Track02

03:17

 

 

All Clear

Track03

04:18

 

 

 

Track04

04:59

 

 

 

Track05

04:20

Start

 

 

Track06

04:38

Selected Track

00

Track07

04:40

Total Time

000:00

Track08

04:11

 

 

 

 

 

4

CD –> USB Rec

 

 

 

 

 

Track 1–13

 

Select Track

Individual

Track01

01:43

Bitrate

Select All

Track02

03:17

 

 

All Clear

Track03

04:18

 

 

 

Track04

04:59

 

 

 

Track05

04:20

Start

 

 

Track06

04:38

Selected Track

01

Track07

04:40

Total Time

003:17

Track08

04:11

 

 

 

 

 

Individual

Select All

All Clear

5

128 kbps 192 kbps 320 kbps

CD –> USB Rec

Track 1–13

 

Select Track

128kbps

Track01

01:43

 

Bitrate

192kbps

Track02

03:17

 

 

 

320kbps

Track03

04:18

 

 

 

 

Track04

04:59

 

 

 

 

Track05

04:20

 

Start

 

 

Track06

04:38

 

Selected Track

03

Track07

04:40

 

Total Time

012:17

Track08

04:11

6 / / / StartENTER 2

CD –> USB Rec

 

 

 

Track 1–13

 

Select Track

 

Track01

01:43

Bitrate

128kbps

Track02

03:17

 

 

 

Track03

04:18

 

 

 

Track04

04:59

 

 

 

Track05

04:20

Start

 

 

Track06

04:38

Selected Track

03

Track07

04:40

Total Time

012:17

Track08

04:11

 

 

 

 

 

CD –> USB Rec

 

 

 

 

 

Track 1–13

 

Track Progress

 

 

Track01

01:43

 

 

 

 

 

Track02

03:17

Total Progress

 

 

Track03

04:18

 

 

 

 

 

 

 

 

 

Track04

04:59

 

 

 

 

 

Track05

04:20

 

 

 

 

 

 

 

Cancel

 

 

Track06

04:38

Selected Track

03

Track07

04:40

Total Time

012:17

Track08

04:11

 

 

 

 

 

 

 

1 USB USB

2USB

99

USB 300

USB STANDBY/ON OPEN/CLOSE DVD

ON USB

32

Zhtw

OK

8

OK

OK

1CD DVD VCD USB

MAIN MIC SUB

MIC (MAIN) MIC (SUB) MIC (MAIN)

USB

3 KARAOKE

SHIFT+KARAOKE

KARAOKE

KARAOKE

OFF

SHIFT+AUDIO USB

Left

Right

STEREO

5MIC VOL +/– 2

麥克風朝向揚聲器。3

體聲音的感覺。4

SHIFT+ECHO

1 3

您的聲音。5

SHIFT+ SHIFT+

08

English

Español

Español

1 SHIFT+KARAOKE SHIFT+ECHO SHIFT+ SHIFT+ MIC VOL NO MIC DVDSTEREO 2.1

DVD/CD USB

2MIC VOL 0

4SFC MP3

5DTS

33

Zhtw

09

9

2 / / / ENTER

 

Video Adjust

 

 

Sharpness

 

Standard

 

 

 

 

1 HOME MENU

Brightness

 

0

Contrast

 

0

Audio Settings

Gamma

 

Off

Hue

 

0

 

 

 

Chroma Level

 

0

 

 

 

 

 

 

 

 

 

 

 

 

 

Audio Settings

 

 

 

 

 

 

 

 

Sharpness

2 / / / ENTER

Fine Standard

 

Soft

 

Audio Settings

 

 

 

 

Audio DRC

High

 

Medium

 

Low

 

Off

Brightness–20 +20

Contrast –16 +16

DRC

High Medium Low Off

Dolby Digital DVDDRC

不會注意有何不同。1

Gamma

High Medium Low Off

Hue

Green 9 9 Red 9 9

Chroma Level–9 +9

/

Brightness

min

max

0

 

3 ENTER Video Adjust

 

HOME MENU

1 HOME MENU

 

 

Video Adjust

 

Video Adjust

1 DRC Dolby Digital

34

Zhtw

10

1DVD/CD

2HOME MENU

Initial Settings

Initial Settings

3 / / / ENTER

明。1

10

English

Español

 

 

 

 

 

 

TV Screen

4:3 (Letter Box)

4:3

 

 

 

51

 

 

4:3 (Pan & Scan)

4:3

 

 

 

 

 

 

 

 

 

16:9 (Wide)

 

 

 

 

 

16:9 (Compressed)

4:3

 

 

2

Component Out

Interlace

 

 

 

 

Progressive

40

ENTER

RETURN

1

TV Screen Audio Language Subtitle Language

DVD DVD

HDMI Resolution HDMI HDMI Color HDMI HDMI

HDMI

2HDMI HDMI 1920 x 1080p 1920 x 1080i 1280 x 720p

HDMI

Español

35

Zhtw

10

 

 

 

 

 

 

HDMI Resolution

1920 x 1080p

1920 x 1080

HDMI *

 

 

1920 x 1080i

1920 x 1080

41

 

 

1280 x 720p

1280 x 720

HDMI

 

 

*

720 x 480p (NTSC)/

720 x 480 (NTSC)/720 x 576 (PAL)

720 x 576p (PAL)

 

PAL/NTSC

 

720 x 480i (NTSC)/

720 x 480 (NTSC)/720 x 576 (PAL)

 

720 x 576i (PAL)

 

 

 

 

HDMI Color

Full range RGB

 

HDMI *

RGB

HDMI DVI

41

 

 

RGB

RGB

HDMI

 

 

Component

8-bit HDMI

*

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Audio Language

English

 

 

 

 

 

 

 

 

 

 

 

 

57

 

 

 

 

 

 

Subtitle Language

English

 

 

 

 

 

 

 

 

 

 

 

 

57

 

 

 

 

 

 

DVD Menu Language

w/Subtitle Lang.

DVD

DVD

 

 

 

 

 

 

 

DVD

 

 

 

 

 

57

 

 

 

 

 

 

Subtitle Display

On

 

 

 

 

Off

DVD

 

 

 

 

36

Zhtw

 

10

 

 

 

 

 

 

 

 

OSD Language

English

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Angle Indicator

On

DVD

 

 

 

 

 

 

 

 

 

 

Off

 

 

 

 

 

 

 

 

 

 

English

 

 

 

 

 

 

 

 

Parental Lock

 

 

 

 

 

 

 

 

 

 

DivX(R) VOD

Display

DivX® VOD

 

 

 

 

 

Español

 

 

 

 

 

 

Speaker Distance

39

 

 

 

Off us (2119)

DVDDVD-Video

地區代碼。1

1 Password

Initial Settings

Video Output

Parental Lock

Password

Language

DivX (R) VOD

Level Change

Display

 

Country Code

Options

 

 

Speakers

 

 

2

ENTER

密碼。

1Password ChangeENTER

2ENTER

Español

1

57

37

Zhtw

10

1Level Change

ENTER

3ENTER

您不能鎖在等級1

58

1Country Code

ENTER

2ENTER

/

效。

DivX® VOD

DivX VOD DivX VOD

DivXVOD 1

DivX VOD

1HOME MENU Initial Settings

2OptionsDivX (R) VOD

Initial Settings

 

 

Video Output

Parental Lock

Display

Language

DivX (R) VOD

 

Display

 

 

Options

 

 

Speakers

 

 

3 Display

DivX VOD

DivX® VOD

DivX VOD DivX VOD

已過的DivX VOD

Rental Expired

DivX VOD

DivX VOD DRM

DivX VOD

Authorization Error

1 57

38

Zhtw

3.0m

相距聆聽位置兩側的揚聲器設定為同等距離。

1HOME MENUInitial Settings

2SpeakersSpeaker Distance

Initial Settings

 

Video Output

Speaker Distance

Language

 

Display

 

Options

 

Speakers

 

3 /

Initial Settings

 

 

Video Output

 

 

Language

L

3.0m

Display

C

3.0m

Options

R

3.0m

Speakers

SR

3.0m

 

SL

3.0m

 

SW

3.0m

5/

L R

L/R

30 cm 30 cm 9 m 1

C 2.1 m 0 m

SL/SR

6.0 m 0 m2

SW 2.1 m 0 m

10

6

ENTER

English

 

 

 

 

 

 

 

Español

Español

1 L R

2 23

39

Zhtw

11

11

LINE 1

L

AC INR

ANALOG

R

FRONT

L

CENTER

R

SURROUND

 

SUB

 

WOOFER

SPEAKERS (4 Ω )

COMPONENT

PR

VIDEO

 

VIDEO(TV)

PB

Y

ADAPTER PORT

VIDEO OUT

5 m 6 m

AM

A

 

 

N

 

 

T

 

 

E

 

 

N

 

 

N

 

FM

A

AM LOOP

UNBAL

HDMI

PAL

HDMI

Bluetooth®

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

KURO LINK

 

 

(LINE 1) AUDIO IN

 

 

MD

RCA

 

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

40

Zhtw