Pioneer SVM-1000 User Manual

2.96 Mb
Loading...

SOUND & VISION MIXER

SVM-1000

Operating Instructions

K057_En
S002_En
D3-4-2-1-7b_A_En
D8-10-1-2_En
D3-4-2-1-7a_A_En
P1-4-2-2_En
D8-10-1-3_EF
D8-10-3a_En
D8-10-2_En
K015 En

Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference.

In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown in the explanatory drawings. However the method of connecting and operating the unit is the same.

IMPORTANT

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

D1-4-2-3_En-A

1)Read these instructions.

2)Keep these instructions.

3)Heed all warnings.

4)Follow all instructions.

5)Do not use this apparatus near water.

6)Clean only with dry cloth.

7)Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8)Do not install near any heat sources such as radiators, heat registers, stoves,

or other apparatus (including amplifiers) that produce heat.

9)Do not defeat the safety purpose of the polarized or grounding-type plug.

A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10)Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11)Only use attachments/accessories specified by the manufacturer.

12)Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13)Unplug this apparatus during lightning storms or when unused for long periods of time.

14)Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

FEDERAL COMMUNICATIONS COMMISSION DECLARATION OF CONFORMITY

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Product Name:

SOUND & VISION MIXER

Model Number:

SVM-1000

Responsible Party Name: PIONEER ELECTRONICS SERVICE, INC.

Address:

1925 E. DOMINGUEZ ST. LONG BEACH, CA 90801-1760, U.S.A.

Phone:

1-800-421-1404

This product contains mercury. Disposal of this material may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronics Industries Alliance : www.eiae.org.

The backlighting lamp of LCD in this equipment contains mercury. Disposal of this material may be regulated due to environmental considerations according to Local, State or Federal Laws. For disposal or recycling information, please contact your local authorities or the Electronics Industries Alliance: www.eiae.org

WARNING

This equipment is not waterproof. To prevent a fire or shock hazard, do not place any container filled with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain

or moisture.

D3-4-2-1-3_B_En

IMPORTANT NOTICE – THE SERIAL NUMBER FOR THIS EQUIPMENT IS LOCATED ON THE REAR. PLEASE WRITE THIS SERIAL NUMBER ON YOUR ENCLOSED WARRANTY CARD AND KEEP IN A SECURE AREA. THIS IS FOR YOUR SECURITY.

D1-4-2-6-1_En

Information to User

Alteration or modifications carried out without appropriate authorization may invalidate the user’s right to operate the equipment.

CAUTION: This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded cables and connectors for connections.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.

CAUTION

The POWER switch on this unit will not completely shut off all power from the AC outlet. Since the power cord serves as the main disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power. Therefore, make sure the unit has been installed so that the power cord can be easily unplugged from the AC outlet in case of an accident. To avoid fire hazard, the power cord should also be unplugged from the AC outlet when left unused for a long period of time (for example, when

on vacation).

D3-4-2-2-2a_A_En

WARNING: Handling the cord on this product or cords associated with accessories sold with the product will expose you to chemicals listed on proposition 65 known to the State of California and other governmental entities to cause cancer and birth defect or other reproductive harm.

Wash hands after handling

D36-P4_A_En

WARNING

To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the equipment.

VENTILATION CAUTION

When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 5 cm at rear, and 3 cm at each

side).

WARNING

Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the equipment on thick carpet or a bed.

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause a fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest PIONEER authorized service center or your dealer for a replacement.

WARNING

This product equipped with a three-wire grounding (earthed) plug - a plug that has a third (grounding) pin. This plug only fits a grounding-type power outlet. If you are unable to insert the plug into an outlet, contact a licensed electrician to replace the outlet with a properly grounded one. Do not defeat the safety purpose of the grounding plug.

D3-4-2-1-6_A_En

D3-4-2-2-1a_A_En
D3-4-2-1-4_A_En mod
D3-4-2-1-7c_A_En

Selecting fine audio equipment such as the unit you’ve just purchased is only the start of your musical enjoyment. Now it’s time to consider how you can maximize the fun and excitement your equipment offers. This manufacturer and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion-and, most importantly, without affecting your sensitive hearing.

Sound can be deceiving. Over time your hearing “comfort level” adapts to higher volumes of sound. So what sounds “normal” can actually be loud and harmful to your hearing. Guard against this by setting your equipment at a safe level BEFORE your hearing adapts.

To establish a safe level:

Start your volume control at a low setting.

Slowly increase the sound until you can hear it comfortably and clearly, and without distortion.

Once you have established a comfortable sound level:

• Set the dial and leave it there.

Taking a minute to do this now will help to prevent hearing damage or loss in the future. After all, we want you listening for a lifetime.

We Want You Listening For A Lifetime

Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since hearing damage from loud noise is often undetectable until it is too late, this manufacturer and the Electronic Industries Association’s Consumer Electronics Group recommend you avoid prolonged exposure to excessive noise. This list of sound levels is included for your protection.

Decibel

Level Example

30 Quiet library, soft whispers

40 Living room, refrigerator, bedroom away from traffic 50 Light traffic, normal conversation, quiet office 60 Air conditioner at 20 feet, sewing machine

70 Vacuum cleaner, hair dryer, noisy restaurant

80Average city traffic, garbage disposals, alarm clock at two feet.

THE FOLLOWING NOISES CAN BE DANGEROUS UNDER CONSTANT EXPOSURE

90 Subway, motorcycle, truck traffic, lawn mower 100 Garbage truck, chain saw, pneumatic drill 120 Rock band concert in front of speakers,

thunderclap

140 Gunshot blast, jet plane

180 Rocket launching pad

Information courtesy of the Deafness Research Foundation.

S001_En

Operating Environment

Operating environment temperature and humidity: +5 ºC – +35 ºC (+41 ºF – +95 ºF); less than 85 %RH (cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light)

WARNING

Before plugging in for the first time, read the following section carefully.

The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit will be used meets the required voltage (e.g., 230V or 120V) written on the bottom panel.

If the AC plug of this unit does not match the AC outlet you want to use, the plug must be removed and appropriate one fitted. Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. If connected to an AC outlet, the cut-off plug can cause severe electrical shock. Make sure it is properly disposed of after removal.

The equipment should be disconnected by removing the mains plug from the wall socket when left unused for a long period of time (for example, when on vacation).

Contents

 

CONFIRM ACCESSORIES..............................................

4

CAUTIONS REGARDING HANDLING............................

4

Location ..........................................................................................

4

Cleaning the Unit...........................................................................

4

Disclaimer ......................................................................................

4

About Copyright .............................................................................

4

FEATURES ....................................................................

4

NAMES AND FUNCTIONS OF PARTS ...........................

6

CONNECTION PANEL ...................................................................

6

OPERATION PANEL ......................................................................

7

CONNECTIONS...........................................................

10

CONNECTING INPUTS ................................................................

10

CONNECTING OUTPUTS ............................................................

11

CONNECTING MICROPHONE AND HEADPHONES ...............

12

CONNECTING THE POWER CORD ............................................

12

BASIC OPERATIONS...................................................

13

FADER CURVE SELECTION .......................................................

14

USING THE VIDEO CONTROL FUNCTIONS .................

15

OPERATING THE VIDEO CROSS FADER ..................................

15

OPERATING THE VIDEO CHANNEL SWITCH ...........................

15

OPERATING IN THE VIDEO SOLO MODE .................................

16

VIDEO MIX EFFECTS CHART ......................................................

16

USING THE EFFECT FUNCTION...................................

17

USING BEAT EFFECTS ................................................................

17

USING TOUCH EFFECTS .............................................................

19

USING TEXT EFFECTS .................................................................

20

EDITING TEXT ...............................................................................

22

DISPLAYING/HIDING THE MASTER MONITOR ........................

22

EFFECT LIST..................................................................................

23

USING THE JPEG VIEWER ..........................................

31

BEFORE USING THE JPEG VIEWER...........................................

31

JPEG VIEWER SETUP ..................................................................

31

THE VIDEO EQUALIZER FUNCTION............................

34

SET UP THE VIDEO EQ ................................................................

34

TURNING THE EQUALIZER ON/OFF ..........................................

34

FADER START FUNCTION ..........................................

35

CROSS FADER START PLAY AND BACK CUE PLAY................

35

PERFORM UTILITY SETUP ..........................................

36

MIDI SETTINGS ............................................................................

36

SYNCHRONIZING AUDIO SIGNALS TO EXTERNAL

 

SEQUENCER, OR USING SVM-1000 INFORMATION TO

 

OPERATE AN EXTERNAL SEQUENCER ....................................

36

MIDI CODE LIST ...........................................................................

37

PERFORM VIDEO MONITOR SETUP .........................................

41

KEYBOARD LANGUAGE SETUP.................................................

41

HARDWARE SETUP....................................................

42

MIC SETTING ................................................................................

42

SYSTEM SETTINGS.......................................................................

42

MASTER OUT SETTINGS .............................................................

43

LCD SETTINGS..............................................................................

43

MONITOR OUT SETTINGS ...........................................................

43

TOUCH PANEL SETTINGS...........................................................

44

RETURNING TO DEFAULT SETTINGS ........................................

44

ENDING HARDWARE SET UP ....................................................

44

TROUBLESHOOTING ..................................................

45

ABOUT THE LCD SCREEN ..........................................................

46

ABOUT MINIATURE FLUORESCENT TUBE TECHNOLOGY .....

46

SPECIFICATIONS........................................................

47

3

En

CONFIRM ACCESSORIES / CAUTIONS REGARDING HANDLING / FEATURES

CONFIRM

FEATURES

ACCESSORIES

4-Channnel Music and Video Synchromix

Power cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Warranty card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Most conventional image mixing devices are limited to the simple mixing of two video images, but Pioneer’s own uniquely developed video blending technology makes it possible to simultaneously mix up to four channels of music and video. Since the synchro control allows the use of fader and equalizers with each channel, a new, wider range of performances is possible with the sensation of using conventional DJ mixers.

CAUTIONS REGARDING HANDLING

Location

Install the unit in a well-ventilated location where it will not be exposed to high temperatures or humidity.

Do not install the unit in a location which is exposed to direct rays of the sun, or near stoves or radiators. Excessive heat can adversely affect the cabinet and internal components. Installation of the unit in a damp or dusty environment may also result in a malfunction or accident. (Avoid installation near cookers etc., where the unit may be exposed to oily smoke, steam or heat.)

When the unit is used inside a carrying case or DJ booth, separate it from the walls or other equipment to improve heat radiation.

Cleaning the Unit

Use a polishing cloth to wipe off dust and dirt.

When the surfaces are very dirty, wipe with a soft cloth dipped in some neutral cleanser diluted five or six times with water and wrung out well, then wipe again with a dry cloth. Do not use furniture wax or cleaners.

Never use thinners, benzene, insecticide sprays or other chemicals on or near this unit, since these will corrode the surfaces.

Disclaimer

Microsoft and Windows are registered trademarks of Microsoft Corporation, registered in the U.S. and other countries.

Apple and Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries.

The typefaces included herein are partially developed by DynaComware Taiwan Inc.

About Copyright

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited consumer uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

In the event that the above noted copy protection function operates in any channel, some effects (DELAY, ECHO, ROLL, REVERSE ROLL) will not function.

“AV Effects” support a wide variety of new performance styles by synchronizing music and video.

Equipped with AV Effects that synchronize music effects and video effects on the large 11-inch LCD touch panel display, allowing up to 30 types of effects to be applied to your music and images.

1Beat effect: Automatically detects the tempo of the currently playing track, and applies effects to music and image in synch with the beat.

2Touch effect: By directly touching the image displayed on the large LCD touch panel, effects can be applied to music and video more intuitively.

3Text effect: Text messages created in synchronization with the automatically detected track tempo can be displayed with effects. Text messages can be entered either by the built-in keyboard or a common USB keyboard.

“JPEG VIEWER” allows use of images stored in external memory for live performances

Up to eight JPEG files saved on SD memory cards or USB memory devices can be downloaded and used as a still image sampler. By applying effects or mixing with other videos and images such as the name of the DJ or event, or graphic logos, you can broaden the potential of your performance. Additionally, JPEG files can be loaded and displayed as an automatic slide show.

Digital sound/video system for high quality sound and image

1 96 kHz/24-bit sampling digital system for high sound quality

Analog signals input from a DJ player are passed through the shortest possible signal path and digitized using a high-fidelity A/D converter with 96 kHz/24-bit sampling, producing optimum quality for digital mixing. Mixing is performed by a 32-bit DSP to eliminate any degradation in sound quality, while simultaneously using ideal filtering to produce optimum sound for DJ play.

In order to realize the greatest possible response, the unit also features a high-rigidity chassis and double-shield construction to suppress unwanted vibrations that might adversely effect sound quality, together with a powerful power section and other highfidelity technology, thus producing clear, powerful club sounds.

2 High-performance video IC digital system for high image quality

Video signals input through the high-performance ADC are processed through a high-performance video DSP rated at 600 MHz/32-bit/4800 MIPS (Million Instructions Per Second), thus preserving the original image’s dynamic range while also suppressing unwanted noise and producing images with high fidelity and quality. The same high quality has also been realized for video effects that normally tend to be a source of image degradation.

4

En

FEATURES

Improved design and operability for new club culture

Based on the concept of creating “a design that fascinates,” the boxy-shape of previous DJ mixers has been restyled toward an edgier and more solid design. Great attention has been given to details of materials and design, such as employing an “illumination display” on the rear panel visible from the dance floor.

Operating panel design emphasizes convenience for simultaneous performances of music and video, with a “channel symmetry layout” centered around the 11-inch LCD touch panel. By arranging each channel section symmetrically, further improvements in operability have been made to assist easy mixing between music and video, so that effects can be enabled dynamically from the LCD touch panel.

Other DJ/VJ performance functions made possible through digital technology

1“VIDEO TRIM” allows adjustment of the luminance of images input to each channel.

2“VIDEO EQUALIZER” assigns parameters such as [RGB], [CONTRAST], [HUE], and [SATURATION] to the equalizer, allowing synchronization of audio equalizing and video controls.

3“AV SYNC” allows the user to select whether audio and video controls are linked or adjusted separately.

4“VIDEO MONITOR SELECTOR” allows the user to choose whether the monitor video output shows master only, all channels, master and each channel, master mixing inversion, etc.

5“FULLY ASSIGNABLE MIDI” allows control of DJ effecter, DJ/ VJ application programs, and other external components.

Installing the SVM-1000 in an EIA rack

The screw holes located on the left and right ends of the front panel (within the side cover) match the 19-inch EIA rack.

Remove the 10 screws (five screws each located on the left and right sides of the unit) before installing the unit to the rack.

Screws

Side cover

Holes for rack installation can be located when the side covers are removed.

Attach the unit to the rack using screws of the appropriate size (screws not provided with the unit).

When installing the unit in a rack, take care to avoid pinching your fingers.

Note

Never place this unit directly above a power amplifier, as the heat given off by the amplifier might result in damage to the unit. Placing the unit directly above a power amplifier might also result in ham radio signals being picked up or in other types of interference.

Allow at least 1U (43.7 mm) space between this component and the one mounted above it, so as to assure that the cords connected to this unit's input/output connectors and terminals do not touch the component above.

Always be sure to remove the unit from its rack before shipping.

When moving the unit while still installed in its rack, exercise caution to avoid subjecting the unit to shocks or vibration.

5

En

NAMES AND FUNCTIONS OF PARTS

NAMES AND FUNCTIONS OF PARTS

CONNECTION PANEL

1

2

3

4

5

6

7

5

 

8

9

 

 

10 11

 

12

6

7

5

2

3

4

5

13

 

4

 

SIGNAL GND

 

3

 

 

AUDIO OUT

 

1 GND 2 HOT

 

 

 

 

 

 

2

 

 

1

SIGNAL GND

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MASTER

REC

 

 

 

 

 

 

 

 

 

 

 

PHONO DVD/LINE

 

LINE

DVD

 

R

MASTER OUT 1

L

3 COLD

 

 

OUT 2

OUT

 

BOOTH

LINE

DVD

 

PHONO DVD/LINE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MONITOR

 

 

 

 

 

 

MIC2

 

L

 

 

L

 

 

 

 

 

 

MASTER

L

 

 

 

(TRS)

L

 

L

 

 

 

 

 

 

 

 

 

 

 

 

 

 

R

L

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ATT.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CONTROL

 

 

CONTROL

 

 

 

 

 

 

 

 

 

 

 

CONTROL

 

CONTROL

 

 

 

 

 

 

 

 

 

 

 

 

-6 dB

-3 dB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0 dB

 

 

 

 

 

 

 

 

 

 

 

 

 

POWER

R

 

 

R

 

 

 

 

 

 

 

 

R

 

 

 

 

R

 

R

 

 

 

 

 

OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ON

 

SYNC

DIGITAL

SYNC

 

 

 

 

 

DIGITAL

OUT

 

 

 

DIGITAL

SYNC

 

 

SYNC

 

MIDI

 

 

 

OUT

OUT

 

14

15 16

 

17

15

OUT

 

14

OUT

 

 

 

 

 

 

IN

 

 

fs (Hz)

 

 

IN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OUT

 

 

 

 

 

 

 

 

 

48 k

96 k

 

 

 

 

 

 

 

 

 

 

 

DVD

 

 

DVD

 

VIDEO OUT

 

MASTER

 

 

 

MONITOR

 

DVD

 

 

DVD

 

 

 

AC IN

S-VIDEO

 

S-VIDEO

 

 

 

COMPONENT

COMPOSITE

 

 

 

S-VIDEO

 

 

S-VIDEO

 

 

USB

 

 

 

 

 

 

 

 

 

Y

CB

CR

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VIDEO

 

 

VIDEO

 

 

 

 

 

 

 

 

S-VIDEO

S-VIDEO

 

VIDEO

 

 

VIDEO

 

 

 

18

 

19

 

19

 

 

 

 

20

 

 

 

 

21

19

 

19

22

23

1POWER switch

2PHONO input connectors

RCA type phono level (MM cartridge) input connectors. Do not use for inputting line level signals.

3 DVD/LINE input connectors

RCA type line level audio input connectors.

Use to connect a DJ/VJ DVD player or DJ CD player or other line level output component.

4 Signal ground terminal (SIGNAL GND)

Connect the ground wire from an analog turntable. This is not a safety ground terminal.

5 CONTROL connector

Connect the Ø 3.5 mm mini phone plug of the control cable from a DJ/VJ DVD player or DJ CD player.

When this is done, this mixer’s fader controls can be used to perform start and back-cue functions on the connected DJ/VJ DVD player or DJ CD player.

6 LINE input connectors

RCA type line level audio input connectors.

Use to connect a cassette deck or other line level output component.

7 DVD input connectors

RCA type line level audio input connectors.

Use to connect a DJ/VJ DVD player or DJ CD player or other line level output component.

8 Audio master output 1 connectors (MASTER OUT 1)

XLR type (male) balanced output.

When using a cord with RCA-type plug, users are recommended to connect the plug directly to the MASTER OUT 2 connectors without using an XLR/RCA converter plug.

When a conversion plug is used, the signal GND may become unstable, in rare cases resulting in the production of noise.

9Audio master output attenuator selector (MASTER ATT.)

Attenuates the output level of the audio master 1 and audio master

Attenuation level can be selected as 0 dB, –3 dB, or –6 dB.

10Audio master output 2 connectors (MASTER OUT 2)

RCA-type unbalanced output.

11Recording output connectors (REC OUT)

RCA type output connectors for recording.

12BOOTH MONITOR output jacks (TRS)

Ø 6.3 mm phone-type booth monitor output jacks.

The sound level output at these connectors can be controlled by the BOOTH MONITOR level dial, regardless of the setting of the MASTER LEVEL dial. (Since the output is TRS, both balanced and unbalanced outputs are supported.)

13 Microphone 2 input jack (MIC 2)

Connect microphones equipped with phone-type plug.

14 Sync signal output connector (SYNC OUT)

Outputs video sync signal.

When connecting a Pioneer DJ/VJ DVD player (sold separately), the sync signal helps suppress any lag between video and audio signals.

15 Digital input connector (DIGITAL IN)

RCA-type digital coaxial input connector. Connect to the digital coaxial output connector from a DJ/VJ DVD player or DJ CD player.

If the sampling frequency of the output signal changes, the sound may be interrupted briefly.

16 Sampling frequency selector switch (fs 48 k/96 k)

Use to set the sampling frequency of the digital output to 96 kHz/ 24-bit format or 48 kHz/24-bit format.

Turn power off before changing this switch position.

17Digital output connector (DIGITAL OUT)

RCA type digital coaxial output connector. Master audio digital output.

18Power inlet (AC IN)

Use the furnished power cable to connect to a household AC outlet.

19Video input connectors (DVD, VIDEO, S-VIDEO)

Composite and S-VIDEO type video input connectors.

20Video master output connectors

(MASTER: COMPONENT, COMPOSITE, S-VIDEO)

Component, composite, and S-VIDEO type video output connectors.

21 Video monitor output connectors (MONITOR, S-VIDEO)

Composite and S-VIDEO type monitor video output connectors.

6

En

NAMES AND FUNCTIONS OF PARTS

22 MIDI OUT connector

23 MIDI USB output connector

DIN type output connector.

USB-B type output connector. Use to connect to a computer.

Use to connect to other MIDI component.

 

OPERATION PANEL

1

 

14 VIDEO INPUT

 

VIDEO INPUT

15

16

 

VIDEO INPUT

17VIDEO INPUT

 

VIDEO

32

USB

 

 

DVD VIDEO S-VIDEO

DVD VIDEO S-VIDEO

 

 

DVD VIDEO S-VIDEO

 

 

 

DVD VIDEO S-VIDEO

MASTER LEVEL

 

 

 

VIDEO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VIDEO

 

 

 

 

 

 

 

 

EX

 

 

 

 

 

18

 

 

 

 

 

 

 

 

 

 

 

EX

 

 

 

CH 1

 

 

VIDEO TRIM

18

VIDEO TRIM

 

 

18

VIDEO TRIM

 

18

VIDEO TRIM

BLACK

WHITE

 

VIDEO

 

 

 

 

 

20

 

 

 

MONO STEREO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EX

 

 

 

 

 

 

 

 

 

 

21

 

 

 

 

 

 

 

 

33

2

CH 4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

UTILITY

 

 

 

 

 

 

 

 

 

 

 

 

MIC

 

 

MIN

MAX

MIN

 

MAX

MASTER

MIN

 

MAX

 

 

MIN

MAX AUDIO MASTER LEVEL

 

 

 

 

MONITOR

CH SELECT

 

 

 

 

 

 

AUDIO INPUT

AUDIO INPUT

SET UP

 

AUDIO INPUT

 

 

 

AUDIO INPUT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DVD/LINE PHONO 19 DVD

LINE

DIGITAL

40

45

DVD

LINE

DIGITAL 22

LINE PHONO

 

 

34

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

23

AUDIO TRIM OVER

23

AUDIO TRIM OVER

VIDEO EQ

 

OVER

AUDIO TRIM

23

OVER

AUDIO TRIM

23

OVER

0

 

 

 

ON/OFF

 

 

 

 

 

 

 

 

 

 

 

 

SET UP

 

 

 

 

 

 

 

 

 

 

 

 

MIC 1

 

 

 

 

 

 

 

 

41

27

 

 

 

 

 

 

 

 

 

 

4

MIC1

 

 

 

 

10

 

 

 

 

10

10

 

 

 

 

 

 

10

 

 

 

10

 

LEVEL

 

 

 

+9

7

 

 

 

+9

7

 

 

7

 

 

+9

 

 

 

7

 

+9

 

7

 

 

 

24

 

HI

4

24

 

HI

 

4

 

VIDEO FX

4

 

HI

 

24

 

4

 

HI

24

4

 

 

 

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MIC2

 

 

2

 

 

 

2

 

PATTERN/

2

 

 

 

 

2

 

 

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

 

 

 

 

 

 

 

 

 

TEXT BANK

 

 

 

 

 

 

 

 

 

 

LEVEL

 

 

 

1

 

 

 

1

 

1

 

 

 

 

1

 

 

1

 

 

 

 

 

 

 

 

 

 

46

 

 

 

 

 

 

 

 

 

35

 

 

0

 

-26

+6

0

 

-26

 

+6

0

 

0

-26

 

+6

 

 

 

0

-26

+6

 

0

 

 

 

–1

 

 

–1

 

–1

 

 

 

 

–1

 

–1

 

HI

 

 

 

MID

 

 

MID

 

 

 

 

MID

 

 

 

 

 

MID

 

 

6

 

25

 

 

–2

25

 

 

 

–2

 

 

–2

 

 

 

25

 

–2

 

 

25

–2

 

 

 

 

 

 

 

 

 

TIME/

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

-12

+12

 

 

–3

 

 

 

–3

 

PARAMETER

–3

 

 

 

 

–3

 

 

–3

 

 

 

 

 

–5

 

 

 

 

–5

 

47

–5

 

 

 

 

 

 

–5

 

 

 

–5

 

 

LOW

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7

 

26

-26

+6

 

26

-26

 

+6

 

 

–7 -26

 

+6

26

 

–7 -26

+6

26

 

 

 

 

–7

 

–7

 

 

 

–7

 

-12

+12

 

LOW

–10

 

LOW

 

–10

 

LEVEL/

–10

LOW

 

 

–10

 

LOW

–10

 

 

 

 

 

 

 

 

 

 

 

JPEG

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TALK

 

 

 

–15

 

 

 

 

–15

DEPTH

–15

 

 

 

 

 

–15

 

 

 

–15

 

8

MIC OFF ON OVER

 

 

 

 

 

 

 

 

 

VIEWER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

–24

 

 

 

 

–24

42

48

–24

 

 

 

 

 

–24

 

 

–24

 

FADER START

 

-26

+6

dB

 

-26

 

+6

dB

dB

-26

 

+6

 

 

dB

 

-26

+6

 

L dB

R

 

 

 

 

 

27

 

 

 

 

27

MIN MAX

 

 

 

 

27

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CH1

 

 

 

 

 

 

 

 

 

EFFECT

 

 

 

 

 

 

 

 

 

 

 

9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

28

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CUE

 

 

 

CUE

 

 

 

CUE

 

 

CUE

 

 

 

 

 

 

CUE

 

CUE

CH2

 

 

 

 

 

 

 

 

 

 

 

28

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

28

2

 

28

 

28

 

 

3

28

 

4

MASTER

 

CH3

 

 

VIDEO

 

 

 

 

 

CH4

 

 

 

 

10

 

 

 

 

10

SOLO MODE

 

10

 

 

 

 

 

10

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

43

49

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9

 

 

 

 

9

9

 

 

 

 

 

9

 

 

 

 

BALANCE

 

HEAD PHONES

 

 

 

8

 

 

 

 

8

8

 

 

 

 

 

8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MONO SPLIT

STEREO

 

 

 

7

 

 

 

 

7

 

 

7

 

 

 

 

 

7

 

 

 

 

 

36

10

 

 

 

 

 

6

 

 

 

 

6

FADER

EFFECT

6

 

 

 

 

 

6

 

 

 

 

 

 

 

 

 

 

5

 

 

 

 

5

5

 

 

 

 

 

5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AV SYNC

ON/OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

 

 

 

4

4

 

 

 

 

 

4

 

 

 

 

 

 

MIXING

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

L

R

 

 

 

 

3

 

 

 

 

3

44

50

3

 

 

 

 

 

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BOOTH MONITOR

 

 

 

 

 

 

2

 

 

 

 

2

2

 

 

 

 

 

2

 

 

 

 

 

 

 

 

 

 

1

 

 

 

 

1

1

 

 

 

 

 

1

 

 

 

 

 

 

11

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0

 

 

 

 

0

 

 

0

 

 

 

 

 

0

 

 

 

 

 

37

CUE

MASTER

 

29

 

 

 

29

 

 

 

 

 

 

 

29

 

 

 

 

 

 

 

 

 

 

29

 

 

 

 

 

 

 

 

 

 

 

LEVEL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0

12

 

 

CROSS FADER

CROSS FADER

 

CROSS FADER

 

 

CROSS FADER

 

 

 

 

 

ASSIGN

 

 

ASSIGN

 

 

 

 

ASSIGN

 

 

 

 

ASSIGN

CH FADER CURVE

 

 

 

 

 

 

 

 

 

 

 

 

30

 

 

 

 

 

 

 

 

 

 

 

 

38

 

 

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A

THRU B

 

 

A

THRU

B

 

 

51

 

A

THRU

B

 

30 A

THRU B

 

 

 

 

PHONES

 

 

30

 

 

 

30

 

CROSS FADER CURVE

 

 

 

SD CARD

 

 

39

13

 

 

 

PROFESSIONAL SOUND&VISION MIXER

A

B

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SVM-1000

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

31

 

 

 

 

 

 

1 USB connector

Use to connect a USB memory or keyboard.

2CH1/CH4 video input connectors (VIDEO EX)

Use to input video from an external source.

3Microphone 1 input jack (MIC 1)

Connect microphone with XLR-type or phone-type plug.

4 Microphone 1 level control dial (MIC 1 LEVEL)

Use to adjust the volume of microphone 1. (Adjustable range – to 0 dB)

5 Microphone 2 level control dial (MIC 2 LEVEL)

Use to adjust the volume of microphone 2. (Adjustable range – to 0 dB)

6 Microphone equalizer high-range adjust dial (HI)

Use to adjust the treble (high-range) frequencies of microphones 1 and 2. (Adjustable range –12 dB to +12 dB)

7 Microphone equalizer low-range adjust dial (LOW)

Use to adjust the bass (low-range) frequencies of microphones 1 and 2. (Adjustable range –12 dB to +12 dB)

8 Microphone function selector switch (MIC)

OFF:

No microphone sound is output.

ON:

Microphone sounds are output, and the microphone function indicator lights.

TALK OVER:

Microphone sounds are output, and the microphone function indicator flashes.

When an audio signal of –15 dB or more (default setting) is input to the microphone input, the talkover function operates to reduce all output other than the mike audio by 20 dB (default setting).

Values can be changed in the hardware setup (P. 42)

When not using the TALK OVER function, it is recommended to set the switch to the [OFF] or [ON] position.

9 FADER START button/indicator (CH-1 to CH-4)

Enables the fader start/back cue function for the channel to which a DJ/VJ DVD player or DJ CD player is connected. The button lights when set to ON. When enabled, the operation differs depending on the setting of the CROSS FADER ASSIGN switch.

When the CROSS FADER ASSIGN switch is set to the [A] or [B] position, FADER START button operation is linked to the operation of the cross fader (and unlinked to channel fader).

When the CROSS FADER ASSIGN switch is set to the [THRU] position, FADER START button operation is linked to the operation of the channel fader (and unlinked to cross fader).

7

En

NAMES AND FUNCTIONS OF PARTS

10 HEADPHONES output switch (MONO SPLIT/STEREO)

MONO SPLIT:

The source sound selected with the headphone CUE button is output to the L channel, while the master sound is output to the R channel (only when [MASTER] is selected with the headphone CUE button).

STEREO:

The audio source selected with the headphone CUE button is output in stereo.

11 HEADPHONES MIXING dial

When rotated clockwise (toward [MASTER]), the master output audio is produced at the headphones (only when [MASTER] has been selected with the headphone CUE button); when rotated counterclockwise (toward [CUE]), the headphones output becomes the mixture of the effect monitor and the channel selected with the headphone CUE button.

12 HEADPHONES LEVEL adjust dial

Adjusts the output level of the headphones jack. (Adjustable range: – to 0 dB)

13Headphones jack (PHONES)

14Channel 1 VIDEO INPUT selector switch

Set to [DVD], [VIDEO], [S-VIDEO], or [VIDEO EX] to match the type of input connected.

15 Channel 2 VIDEO INPUT selector switch

Set to [DVD], [VIDEO], or [S-VIDEO] to match the type of input connected.

16 Channel 3 VIDEO INPUT selector switch

Set to [DVD], [VIDEO], or [S-VIDEO] to match the type of input connected.

17 Channel 4 VIDEO INPUT selector switch

Set to [DVD], [VIDEO], [S-VIDEO], or [VIDEO EX] to match the type of input connected.

18 VIDEO TRIM dial

Use to adjust the level of the video input signal for each channel.

When rotated counterclockwise, the luminance level is reduced, eventually producing a black screen.

When rotated clockwise, the luminance level is raised, eventually producing a white screen.

At the center position, the luminance level is neutral (same level as input).

19 Channel 1 AUDIO INPUT selector switch

DVD/LINE:

Use to select DVD/LINE input connectors (line level analog input).

PHONO:

Use to select PHONO input connectors (PHONO level analog input).

20 Channel 2 AUDIO INPUT selector switch

DVD:

Use to select DVD input connectors.

LINE:

Use to select LINE input connectors (line level analog input).

DIGITAL:

Use to select DIGITAL input connector.

21 Channel 3 AUDIO INPUT selector switch

DVD:

Use to select DVD input connectors.

LINE:

Use to select LINE input connectors (line level analog input).

DIGITAL:

Use to select DIGITAL input connector.

22 Channel 4 AUDIO INPUT selector switch DVD/LINE:

Use to select DVD/LINE input connectors (line level analog input).

PHONO:

Use to select PHONO input connectors (PHONO level analog input).

8

23 AUDIO TRIM dial

Use to adjust the level of the audio input signal for each channel. (Adjustable range: – to +9 dB, mid-position is about 0 dB)

24 Channel equalizer high-range adjust dial (HI)

Use to adjust the treble (high-range) frequency sound for each channel. Video parameters can also be assigned. See P. 34 regarding video parameters. (Adjustable range: –26 dB to +6 dB)

25 Channel equalizer mid-range adjust dial (MID)

Use to adjust the mid-range frequency sound for each channel. Video parameters can also be assigned. See P. 34 regarding video parameters. (Adjustable range: –26 dB to +6 dB)

26 Channel equalizer low-range adjust dial (LOW)

Use to adjust the bass (low-range) frequency sound for each channel. Video parameters can also be assigned. See P. 34 regarding video parameters. (Adjustable range: –26 dB to +6 dB)

27 Channel level indicator

Displays the current level for each channel, with two-second peak hold.

28 Headphone CUE buttons/indicators

These buttons are used to select from 1 to 4, MASTER, or EFFECT CUE, to allow you to monitor the desired source through headphones. If multiple buttons are pressed simultaneously, the selected audio sources are mixed. Press the button once more to cancel the selected source. Unselected buttons glow darkly, while selected source buttons light brightly.

29 Channel fader lever

Use to adjust sound volumes and video level for each channel. (Volume adjust range: – to 0 dB) (Video adjust range: 0 % to 100 %)

Output is in accordance with the channel fader curve selected with the CH FADER CURVE switch.

When FADER AV SYNC function is OFF, only sound volume can be adjusted.

30 CROSS FADER ASSIGN switch

This switch assigns each channel’s output to either right or left side of the cross fader (if multiple channels are assigned to the same side, the result will be the combined sum of the channels).

A:

The selected channel is assigned to the cross fader’s [A] (left) side.

THRU:

The channel fader’s output is sent as is to the master output, without being passed through the cross fader.

B:

The selected channel is assigned to the cross fader’s [B] (right) side.

31 CROSS FADER CURVE switch

This switch allows the user to select from three types of cross fader curve response.

Sound volume changes as follows:

At the left setting, the curve produces a rapid signal rise. (As soon as the cross fader lever leaves the [A] side, the [B] channel sound is produced.)

At the right setting, the curve operates to produce an even, neutral rise throughout the cross fader’s movement.

At the middle setting, an intermediate curve is produced, midway between the two curves noted above.

The video level is as noted above only when the video cross fader’s video mix effect is set to [FADE].

32Video master output level dial (VIDEO MASTER LEVEL)

Adjusts the video master output luminance level.

33Master output MONO/STEREO selector switch

When set to the [MONO] position, audio master output is produced in L+R monaural.

34 Audio master output level dial (AUDIO MASTER LEVEL)

Use to adjust the master output level. (Adjustable range: – to 0 dB)

The master output is the sum combination of the sound from channels set to [THRU] with the CROSS FADER ASSIGN switch; the signal passed through the cross fader; and the signals from microphone 1 and microphone 2.

En

NAMES AND FUNCTIONS OF PARTS

35 Master level indicator (MASTER L, R)

These segment indicators display the audio output level from L and R channels. The indicators have a two-second peak hold.

36 Master balance dial (BALANCE)

Use to adjust the L/R channel balance for audio master output, booth monitor output, recording output, and digital output.

37 BOOTH MONITOR level control dial

This dial is used to adjust the booth monitor output volume. The volume can be adjusted independently of the master output level. (Adjustable range: – to 0 dB)

38 Channel fader curve switch (CH FADER CURVE)

This switch allows the user to select from three types of channel fader curve response.

The sound volume and video level changes as follows: This setting is applied equally to channels 1 to 4.

At the left setting, the curve operates to produce a rapid rise as the channel fader approaches its distant position.

At the right setting, the curve operates to produce an even, neutral rise throughout the channel fader’s movement.

At the middle setting, an intermediate curve is produced, midway between the two curves noted above.

39SD CARD slot

Insert an SD card.

40UTILITY button (MASTER MONITOR, SET UP)

Switches between display / no display of the master monitor on the LCD. When the master monitor is set to display, the indicator lights. When the button is held depressed, the indicator changes to flashing, and the LCD screen changes to show the utility setup menu.

41 VIDEO EQ button (ON/OFF, SET UP)

Switches the video equalizer ON/OFF. The indicator lights when the video equalizer is ON. When the button is held depressed, the indicator flashes, and the LCD display changes to show the equalizer setup menu.

42 JPEG VIEWER button

Use to set the JPEG viewer mode. The indicator lights when in the JPEG viewer mode.

43 VIDEO SOLO MODE button

Use to switch the video solo mode ON/OFF. When the video solo mode is ON, the indicator will flash.

44 Fader AV synchro button (FADER AV SYNC)

This button determines whether sound and video are controlled together, or independently. When set to ON, the indicator lights, and the channel fader and cross fader operations change both sound and video simultaneously. When set to OFF, the channel fader and cross fader levers control sound only, while video is controlled by the touch panel.

45 Effect channel selector dial (CH SELECT)

Use to select the channel to which effects are applied. When [MIC] is selected, effects are applied to both microphone 1 and microphone 2.

46 VIDEO FX PATTERN/TEXT BANK dial

Use to select video effects, video effect patterns and text banks.

47 Effect parameter 1 dial (TIME/PARAMETER)

Adjusts parameter for selected effect.

If this dial is rotated while depressing the TAP button, direct BPM can be set manually.

48Effect parameter 2 dial (LEVEL/DEPTH)

Adjusts quantitative parameters for selected effect.

49TAP button

The BPM is calculated from the intervals at which the TAP button is struck.

50 Effect button/indicator (EFFECT ON/OFF)

Turns selected effect ON/OFF.

When power is turned ON, the button lights (defaults to effect OFF). When effects are enabled (ON), the button flashes.

51 Cross fader lever (A/B)

This adjusts sound and video levels assigned to sides [A] and [B] in accordance with the CROSS FADER ASSIGN switches. When FADER AV SYNC is OFF, the control adjusts the sound only.

9

En

CONNECTIONS

CONNECTIONS

Always turn off the power switch and disconnect the power plug from its outlet when making or changing connections.

CONNECTING INPUTS

 

4

SIGNAL GND

3

 

2

 

1

SIGNAL GND

 

 

PHONO DVD/LINE

LINE

DVD

LINE

DVD

PHONO DVD/LINE

 

 

L

 

 

 

L

 

L

 

 

 

 

CONTROL

 

CONTROL

 

CONTROL

 

CONTROL

 

POWER

R

 

R

 

R

 

R

 

 

OFF

 

 

 

 

 

 

 

 

 

ON

SYNC

DIGITAL

SYNC

DIGITAL

SYNC

 

SYNC

MIDI

 

 

OUT

OUT

OUT

 

OUT

 

 

 

IN

 

IN

 

 

 

 

 

 

 

 

96 k

 

 

 

 

AC IN

 

 

 

 

 

 

S-VIDEO

 

 

L R

 

L R

 

L R

L R

L R

 

R L

Cassette deck, etc.

CD player, etc.

Analog turntable

DJ/VJ DVD player or

DJ/VJ DVD player or

Analog turntable

 

DJ CD player

DJ CD player

 

Pioneer DJ/VJ DVD players or DJ CD players

Audio cable connection

A DJ/VJ DVD or DJ CD player’s audio output connectors can be connected to this unit’s DVD, DVD/LINE or LINE connectors. When using the player’s digital output, connect to this unit’s channel 2 or channel 3 DIGITAL IN connector. Use the AUDIO INPUT selector switch (on top panel of this unit) to select the proper connector.

Likewise, the control cord should be connected to the CONTROL connector of the selected channel.

Video cable connection

A DJ/VJ DVD player’s video output connectors can be connected to this unit’s DVD, VIDEO, or S-VIDEO connectors. When this is done, use the VIDEO INPUT selector switch (on top panel of this unit) to select the proper connector.

Likewise, connect a commercially available sync signal cable to the SYNC OUT connector of the selected channel.

Connecting an analog turntable

Connect the audio output cables from an analog turntable to this unit’s Channel 1 or 4 PHONO input connectors, then set the connected channel’s AUDIO INPUT switch (on the upper panel of this unit) to [PHONO]. This unit’s PHONO input supports MM cartridges.

Connect the ground wire from an analog turntable to the SIGNAL GND terminal of the SVM-1000.

Note that no PHONO input connector is provided for channel 2 and 3.

Connecting other line level output devices

To use a cassette deck or ordinary CD player, connect its audio output connectors to one of the SVM-1000's LINE input connectors (channel 1 to 4).

10

En

CONNECTIONS

CONNECTING OUTPUTS

Power amplifier (RCA plug input connectors)

MASTER ATT. switch

R L

Cassette deck

Digital input AV amplifier

(analog input

 

(digital input

recording device)

 

recording device)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

L

R

 

4

SIGNAL GND

3

 

AUDIO OUT

 

1 GND 2 HOT

 

 

 

 

2

 

1

SIGNAL GND

 

 

 

 

 

 

 

 

 

MASTER

REC

 

 

 

 

 

 

 

 

PHONO DVD/LINE

LINE

DVD

MASTER OUT 1

L

3 COLD

OUT 2

OUT

BOOTH

 

LINE

DVD

PHONO DVD/LINE

 

 

 

 

 

 

R

 

 

MONITOR

 

 

 

 

 

MIC2

 

L

L

 

 

 

 

MASTER L

 

(TRS)

 

L

 

L

 

 

 

 

 

 

 

R

L

 

 

 

 

 

 

 

 

 

 

 

ATT.

 

 

 

 

 

 

 

 

CONTROL

 

CONTROL

 

 

 

 

 

 

 

CONTROL

 

CONTROL

 

 

 

 

 

 

-3 dB

 

 

 

 

 

 

 

 

 

 

 

 

 

-6 dB

0 dB

 

 

 

 

 

 

 

 

POWER

R

R

 

 

 

 

 

R

 

 

 

R

 

R

 

 

OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ON

SYNC

DIGITAL

SYNC

 

 

 

DIGITAL OUT

 

 

 

DIGITAL

SYNC

 

SYNC

MIDI

 

 

OUT

OUT

 

 

 

 

 

 

OUT

 

OUT

 

 

 

IN

 

 

 

fs (Hz)

 

 

 

IN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OUT

 

 

 

 

 

 

 

48 k

96 k

 

 

 

 

 

 

 

 

 

DVD

 

DVD

VIDEO OUT

 

MASTER

 

 

MONITOR

 

 

DVD

 

DVD

 

AC IN

S-VIDEO

 

S-VIDEO

 

COMPONENT

COMPOSITE

 

 

 

S-VIDEO

 

S-VIDEO

 

USB

 

 

Y

CB

CR

 

 

 

 

 

 

 

 

 

VIDEO

 

VIDEO

 

 

 

 

S-VIDEO

S-VIDEO

 

 

VIDEO

 

VIDEO

 

Sampling frequency selector switch

Power amplifier

Plasma display

Display

Power amplifier

(XLR plug input connectors)

 

(for monitor)

(for booth monitor)

Audio master output

This unit is furnished with balanced output MASTER OUT 1 (supporting XLR plugs), and unbalanced output MASTER OUT 2 (supporting RCA plugs).

Using the MASTER ATT. switch, adjust the output level to match the input sensitivity of the power amplifier used.

If the operating panel’s MONO/STEREO switch is set to [MONO], the master output will be a monaural combination of L+R channels.

Recording output

These are output connectors for recording, supporting RCA plugs.

Digital output

This is a coaxial digital output connector, supporting RCA plugs. The sampling frequency can be set to 96 kHz/24-bit format or

48 kHz/24-bit format to match the connected device. Turn power off before changing this switch position.

Booth monitor output

TRS output for ø 6.3 mm phone plug. The sound volume for this output is controlled by the BOOTH MONITOR level dial, independently of the master output level setting.

Video master output

Supports component, composite (RCA, BNC connector) and S- VIDEO outputs.

Monitor output

Supports composite and S-VIDEO outputs.

11

En

CONNECTIONS

CONNECTING MICROPHONE AND HEADPHONES

Microphone

A microphone with XLR-type or Ø 6.3 mm phone-type plug can be connected to the MIC 1 connector on the operation panel (upper) . The MIC 2 jack on the connection panel (rear) can be used to connect a microphone with Ø 6.3 mm phone-type plug.

When using a microphone, set the operating panel’s MIC switch to [ON] or [TALK OVER], and adjust the LEVEL dial as necessary.

When not using a microphone, it is recommended to set the

MIC switch to [OFF] and rotate the LEVEL dial fully counterclockwise to the [–] side.

HEAD PHONES

8

MONO SPLIT

STEREO

7

 

 

6

 

 

5

MIXING

4

3

 

 

2

 

 

1

 

 

0

CUE

MASTER

 

LEVEL

 

 

 

CROSS FADER

 

 

ASSIGN

 

0

 

 

 

A THRU B

PHONES

 

 

 

PROFESSIONAL SO

Headphones

 

SVM

USB

Microphone 1

CH 1

VIDEO

EX

CH 4

MIC

MIC 1

External video connector

MIC2

MIDI

OUT

Microphone 2

USB

Headphones

The PHONES jack on the operating panel (upper) can be used to connect headphones with a Ø 6.3 mm stereo phone plug.

A camera, DVD player or other video output device can be connected to the CH 1/CH 4 video input connectors on the operating panel (top).

 

USB

 

CH 1

 

VIDEO

 

EX

 

CH 4

 

MIC

Video cameras and

 

devices

MIC 1

CONNECTING THE POWER CORD

Connect the power cord last.

When all connections are completed, connect one end of the furnished power cord to the AC inlet on the rear panel, and the plug on the other end to a household AC outlet, or the auxiliary power outlet on an amplifier. Use only the furnished power cord for this connection.

12

En

+ 36 hidden pages