Pioneer SUPER TUNER AVIC-Z110BT User Manual 2

8.81 Mb

Operation Manual

FLASH MEMORY MULTIMEDIA AV NAVIGATION

RECEIVER

AVIC-Z110BT

Notice to all users:

This software requires that the navigation system is properly connected to your vehicles parking brake and depending on your vehicle, additional installation may be required. For more information, please contact your Authorized Pioneer Electronics retailer or call us at (800) 421-1404.

English

Contents

Thank you for buying this Pioneer product.

Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, keep this manual in a safe place for future reference.

Important

The screens shown in the examples may differ from actual screens.

Actual screens may be changed without notice for performance and function improvements.

Introduction

Information to User 9

License Agreement 10

PIONEER AVIC-Z110BT - for U.S.A. 10

PIONEER AVIC-Z110BT - for Canada 12

Terms and Conditions for the Tele Atlas Data 14

Licenses 17

About the database 20

About the Data for the Map Database 20

Copyright Notices for North American data 20

Important Safety Information

21

 

“GOOG-411” service 22

 

 

 

Additional Safety Information

22

 

Parking brake interlock

22

 

When using a display connected to

 

REAR MONITOR OUTPUT

23

 

To avoid battery exhaustion

23

 

Rear view camera

23

 

 

 

Notes Before Using the System

23

 

Failure to operate

23

 

 

 

Visit Our Web site

24

 

 

 

Manual overview

24

 

 

 

 

How to use this manual

24

 

Terminology

24

 

 

 

 

Definitions of terminology

25

 

Notice regarding video viewing

 

25

 

Notice regarding DVD-Video viewing

25

Notice regarding MP3 file usage

25

 

iPod compatibility

25

 

 

 

 

Map coverage 26

 

 

 

 

 

Protecting the LCD panel and screen

26

Notes on internal memory 26

Before removing the vehicle

 

battery 26

Data subject to erasure 26

Basic operation

 

 

 

 

 

Checking part names and functions

27

 

Adjusting the LCD panel angle

28

 

 

Inserting and ejecting a disc

28

 

 

Inserting a disc

29

 

 

 

 

Ejecting a disc

29

 

 

 

 

Inserting and ejecting an SD memory

 

card

29

 

 

 

 

 

Inserting an SD memory card

29

 

Ejecting an SD memory card

30

 

Plugging and unplugging a USB storage

 

device

30

 

 

 

 

 

Plugging in a USB storage device

31

Unplugging a USB storage device

31

Connecting and disconnecting an iPod

31

Connecting your iPod

31

 

 

 

Disconnecting your iPod

31

 

 

Flow from startup to termination

31

 

On first-time startup

32

 

 

 

 

Regular startup 32

 

 

 

 

 

How to use the navigation menu screens

Screen switching overview

34

 

 

What you can do on each menu 35

 

 

Operating list screens (e.g. POI list)

35

 

Shortcut menu 35

 

 

 

Selecting the Shortcut

36

 

 

Canceling the Shortcut 36

 

 

Displaying the rear view camera image

36

How to use the map

 

 

 

How to read the map screen

37

 

 

Displaying the AV information bar

38

Enlarged map of the intersection

39

Display during freeway driving

39

 

Operating the map screen

39

 

 

Changing the scale of the map

39

Switching the map orientation

39

 

2

En

Contents

Scrolling the map to the position you

 

want to see

40

Quick Access

40

Customizing the map screen settings

Setting the Item on the Map Screen 42

Setting “Close Up View” 42

 

City Map

42

 

 

Setting the switching of the city map

 

display

42

 

 

Show Traffic Incident

43

 

Bluetooth Connected

43

 

Setting the current street name

 

 

display

43

 

 

Setting the Favorites icon display

43

3D Land Mark 43

 

 

Displaying maneuvers

43

 

MSN Direct 44

 

 

Displaying POI on the map

44

 

Displaying preinstalled POIs on the

 

map 44

 

 

 

Displaying the customized POIs

45

Switching the view mode 45

Setting the map color change between day

and night 46

 

 

 

Changing the road color

46

 

 

Changing the setting of navigation

 

interruption screen 47

 

 

 

Selecting “Quick Access” 47

 

 

Setting a route to your destination

 

The basic flow of creating your route

48

Checking the location on the map 48

Checking the calculated route

48

 

Display multiple routes

49

 

Modifying the route calculation

 

 

conditions 49

 

 

 

Checking the current itinerary

50

Adding a waypoint

50

 

 

Checking and modifying the current route

Checking the current itinerary 52 Editing waypoints 52

Adding a waypoint

52

Deleting a waypoint

53

Sorting waypoints

53

Modifying the route calculation conditions 53

Canceling the route guidance 54

Searching for and selecting a location

Searching for a location by address

55

Searching for a city name first

55

Finding the location by specifying the

 

house number 56

 

Searching for a name by entering multiple keywords 57

Setting up a route to your home

57

 

Searching for Points of Interest (POI)

58

Searching for POIs by specifying a

 

category first

58

 

 

Searching for a POI directly from the

 

name of the facilities 58

 

 

Searching for a nearby POI

58

 

Searching for POIs around the

 

 

destination

59

 

 

Searching for POIs around the city 59

Selecting destination from “Favorites”

59

Searching for POIs by using the data on the SD memory card 60

Selecting a location you searched for recently 60

Searching for a location by coordinates 60

Registering and editing locations

Registering a location into “Favorites” 62

Registering a location by “Favorites” 62

Registering a location by scroll mode 62

Editing registered locations 62

Editing the entry in “Favorites” 62

Editing your home 63

Sorting the entry in “Favorites” 63

Deleting the entry in “Favorites” 63 Exporting and importing the entry in

“Favorites” 64

En 3

Contents

Exporting the entry in “Favorites” 64

Importing “Favorites” edited on “AVIC FEEDS” 64

Deleting an entry in “History” 65

Browsing information on MSN Direct

Activating the service 66

Checking your product key 66

Subscribing to the MSN Direct

 

service 67

Activating the MSN Direct function 67

Browsing gas prices

67

Browsing movie times

68

– Searching for a theater by selecting a movie title 68

Searching for a movie title by selecting a theater 69

Browsing weather information 69

– Checking the local weather information 69

Checking worldwide weather conditions 70

Using traffic information 70

Viewing the traffic event 70

Checking traffic information on the

 

route 71

How to read traffic information on the map 71

Setting an alternative route to avoid

traffic congestion 72

– Viewing the traffic flow 73

Selecting traffic information to display 74

Browsing local events

74

 

Browsing news headlines 75

 

Browsing stock quotes

76

 

Selecting stock symbols 76

 

Viewing the detailed stock quotes 76

Registering and connecting the

 

Bluetooth device

 

 

Preparing communication devices

77

Registering your Bluetooth devices

77

Searching for nearby Bluetooth

 

devices

77

 

 

Searching for a specified Bluetooth

 

device

78

 

 

Pairing from your Bluetooth

 

 

devices

79

 

 

Deleting a registered device

80

Connecting a registered Bluetooth

device 80

 

 

 

Using hands-free phoning

 

Displaying the Phone Menu 82

 

Making a phone call

82

 

Direct dialing

82

 

Making a call home easily

83

Calling a number in the “Contacts List” 83

Making a phone call using the received

 

call history

83

 

 

 

 

Making a phone call using the dialed

 

number history

84

 

 

 

Making a phone call using missed call

 

history

84

 

 

 

 

 

 

Dialing GOOG-411

85

 

 

 

Dialing the entry in the “Favorites”

85

Dialing a facility’s phone number

85

Dialing from the map

85

 

 

Receiving a phone call

86

 

 

 

Answering an incoming call

86

 

Rejecting an incoming call

86

 

Transferring the phone book

87

 

 

Setting the “Bluetooth Settings” 87

 

Editing the device name 88

 

 

Editing the password

88

 

 

Stopping Bluetooth wave

 

 

 

transmission

88

 

 

 

 

Echo canceling and noise

 

 

 

reduction

88

 

 

 

 

 

Answering a call automatically 88

 

Setting the automatic rejection

 

 

function

89

 

 

 

 

 

Clearing memory

89

 

 

 

Updating the Bluetooth wireless technology software 89

4 En

Contents

Notes for hands-free phoning

90

 

 

Customizing preferences

 

 

 

The options in the “Navi Settings” menu

92

Displaying the “Navi Settings”

 

 

 

screen

92

 

 

 

Checking the connections of leads

92

Checking sensor learning status and

 

driving status 92

 

 

 

Using the “Gas Mileage” function

94

Recording your travel history

95

 

Using the demonstration guidance

96

Registering your home

96

 

 

Correcting the current location

96

 

Options on the “System Settings” menu

96

Displaying the “System Settings”

 

 

screen

96

 

 

 

Customizing the regional settings

97

Setting the Volume for Guidance and Phone 98

Changing the splash screen

99

Changing to the splash screen stored

 

in the SD memory card 99

 

Setting for rear view camera

99

Adjusting the response positions of the touch panel (touch panel

 

calibration)

100

 

Setting the illumination color 100

Checking the version information 101

Replicating the settings

101

Turning off the screen

102

Using the radio (FM)

 

Reading the screen

103

Using the touch panel keys 103

Switching between the detailed information display and the preset list

display 104

Storing and recalling broadcast frequencies 104

Using the “Function” menu 104

Storing the strongest broadcast

 

frequencies 104

Tuning in strong signals 105

Using the radio (AM)

Reading the screen 106

Using the touch panel keys 106

Switching between the detailed information display and the preset list

display 106

Storing and recalling broadcast frequencies 107

Using the “Function” menu

107

Storing the strongest broadcast

 

frequencies

107

 

Tuning in strong signals 107

HD RadioäReception

 

Reading the screen

108

 

Using the touch panel keys

108

Switching between the detailed information display and the preset list

display 109

Storing and recalling broadcast frequencies 109

Switching the display

109

 

 

 

Using the “Function” menu

109

 

– Storing the strongest broadcast

 

frequencies 110

 

 

 

– Switching the seek mode

110

 

– Tuning in strong signals

110

 

– Switching the reception mode

110

Playing audio CDs

 

 

 

 

Reading the screen

111

 

 

 

Using the touch panel keys

111

 

Selecting a track from the list

 

112

 

Using the “Function” menu

112

 

Playing music files on ROM

 

 

Reading the screen

113

 

 

 

Using the touch panel keys

114

 

– Selecting a track from the list 114

Using the “Function” menu

114

 

Playing a DVD-Video

 

 

 

Reading the screen

116

 

 

 

Using the touch panel keys

116

 

– Resuming playback (Bookmark)

117

En 5

Contents

Searching for a specific scene and starting playback from a specified

 

time

118

 

 

Direct number search

118

Operating the DVD menu

118

Using DVD menu by touch panel

 

keys

118

 

 

Frame-by-frame playback

119

Slow motion playback

119

Using the “Function” menu

119

 

Playing a DVD-VR disc

 

 

Reading the screen 121

 

 

Using the touch panel keys

121

 

Searching for a specific scene and starting playback from a specified time 122

Switch the playback mode

123

Using the short-time skip

 

 

function 123

 

Playing by selecting from the title

 

list 123

 

Frame-by-frame playback

123

Slow motion playback

123

Using the “Function” menu

123

Playing a DivX video

 

Reading the screen 125

 

Using the touch panel keys

125

Frame-by-frame playback 126

Slow motion playback

126

Searching for a specific scene and starting playback from a specified time 126

Playing by selecting from the title list 127

Using the “Function” menu 127

DVD-Video, DVD-VR, DivX setup

Displaying DVD/DivX® Setup menu 128 Setting the top-priority languages 128 Setting the angle icon display 128

Setting the aspect ratio

128

Setting the parental lock

129

Setting the code number and level 129

Setting “Auto Play” 129

 

Setting the subtitle file for DivX

130

Language code chart for DVDs

131

Playing music files (from USB or SD)

Starting procedure

132

 

Reading the screen

132

 

Using the touch panel keys (Music)

133

– Selecting a track from the list

133

Using the “Function” menu 134

 

Playing video files (from USB or SD)

Starting procedure

135

Reading the screen

135

Using the touch panel keys (Video) 135

– Playing by selecting from the title list 136

Searching for a specific scene and starting playback from a specified time 136

Using the “Function” menu

137

Using an iPod (iPod)

 

Starting procedure

138

 

Reading the screen

138

 

Using the touch panel keys (Music) 139

– Browsing for a song

139

Operating this navigation system's iPod

function from your iPod

140

Starting the video playback

140

Using the touch panel keys (Video) 141

– Browsing for a video

141

Using the “Function” menu

142

Using the Bluetooth audio player

Reading the screen

144

 

Using the touch panel keys

145

Using the “Function” menu

145

Using the XM tuner

 

 

Reading the screen

146

 

Using the touch panel keys

147

– Selecting an XM channel directly 147

6 En

Contents

Displaying the Radio ID

147

Storing and recalling broadcast

 

stations 148

 

Selecting a channel from the list 148

Using “My Mix” function

148

Using the direct traffic announcement function 149

Using the “Function” menu

149

Setting the memorized songs 150

Using the SIRIUS tuner

 

Reading the screen 151

 

Using the touch panel keys

151

Selecting a SIRIUS channel

 

directly

152

 

Display the Radio ID

152

Storing and recalling broadcast

 

stations

153

 

Using “My Mix” function 153

Using the direct traffic announcement

 

function

153

 

Using the “Instant Replay” function 154

Using the “Function” menu

154

 

– Setting the memorized songs

154

– Using the Game Alert function

155

– Displaying Game Information

155

Using AV input

 

 

Using AV1

156

 

 

Using AV2

156

 

 

Using the touch panel keys

156

 

Using the external unit (EXT1, EXT2)

Reading the screen 157

Using the touch panel keys 157

Other functions

Selecting the video for “Rear display” 158 Operating the picture adjustment 158

Customizing preferences

Options on the “AV System Settings” menu 160

Displaying the “AV System Settings” menu 160

Setting video input 1 (AV1)

160

Setting video input 2 (AV2)

160

Switching the auto antenna

 

 

setting 160

 

 

Changing the wide screen mode 161

Setting the rear output

161

 

Switching the muting/attenuation

 

timing

161

 

 

Switching the muting/attenuation

 

level

162

 

 

Changing the voice output of the

 

navigation guidance

162

 

Acquiring/Cataloging iPod music

 

information 162

 

 

Displaying your DivX VOD registration code 163

The “AV Sound Settings” menu options 163

Displaying the “AV Sound Settings” menu 163

Using balance adjustment 164

Using the equalizer

164

 

Adjusting loudness

166

 

Using subwoofer output

166

Using the high pass filter

166

Adjusting source levels

166

Enhancing bass (Bass Booster) 167

Setting the simulated sound stage 167

Operating Your Navigation System with

Voice

 

 

 

To Ensure Safe Driving

168

 

 

Basics of Voice Operation 168

 

Flow of voice operation

168

 

Starting voice operation

168

 

How to use the voice operation 168

Available Basic Voice Commands

170

Basic commands

170

 

 

Voice operation for the iPod

170

Voice operation for AV source (other than iPod) 171

En 7

Contents

Voice commands related to hands-free phoning 172

Tips for Voice Operation 173

Other functions

Setting the anti-theft function 174

Setting the password

174

Entering the password

174

Deleting the password

174

Forgotten passwords

174

Restoring the default setting

175

Returning the navigation system to the initial state 175

Returning the navigation system to the default or factory settings 175

– Setting items to be deleted 176

Appendix

Troubleshooting 178

Messages and how to react to them 182 Messages for audio functions 184

Positioning technology

186

– Positioning by GPS

186

Positioning by “Dead Reckoning” 186

How do GPS and “Dead Reckoning”

work together? 186 Handling large errors 187

– When positioning by GPS is impossible 187

Conditions likely to cause noticeable positioning errors 188

Route setting information

189

Route search specifications 189

Handling and care of discs

190

Built-in drive and care

191

Ambient conditions for playing a disc 191

Playable discs 191

 

DVD-Video and CD

191

AVCHD recorded discs 191

Playing DualDisc

192

Dolby Digital

192

 

DTS sound

192

 

Detailed information for playable media 192

Compatibility

192

Media compatibility chart 195

Bluetooth

198

 

About the SAT RADIO READY Logo 199

HD Radio Technology 199

SD and SDHC logo

199

WMA/WMV

199

 

DivX

199

 

 

AAC

200

 

 

Detailed information regarding connectable

iPods

200

– iPod

200

iPhone 200

iTunes 200

Using the LCD screen correctly

201

Handling the LCD screen

201

Liquid crystal display (LCD)

 

 

screen 201

 

Maintaining the LCD screen 201

LED (light-emitting diode) backlight 201

Display information

202

Destination Menu 202

Phone Menu

202

Settings Menu

202

Glossary 206

Specifications 209

8 En

 

Chapter

Introduction

01

 

 

Information to User

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Alteration or modifications carried out without appropriate authorization may invalidate the user’s right to operate the equipment.

FCC ID : AJDK026

IC : 775E-K026

This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.

MADE IN THAILAND

For Canadian model

This Class B digital apparatus complies with Canadian ICES-003.

This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

This equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated with at least 20cm and more between the radiator and person’s body (excluding extremities: hands, wrists, feet and ankles).

CAUTION:

USE OF CONTROL OR ADJUSTMENT OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. CAUTION:

THE USE OF OPTICAL INSTRUMENTS WITH THIS PRODUCT WILL INCREASE EYE HAZARD.

WARNING

Handling the cord on this product or cords associated with accessories sold with the product will expose you to chemicals listed on proposition 65 known to the State of California and other governmental entities to cause cancer and birth defect or other reproductive harm. Wash hands after handling.

Introduction

En

9

Chapter

 

 

 

01

Introduction

 

 

 

 

 

 

 

 

License Agreement

other means. You shall not use the Software to

 

PIONEER AVIC-Z110BT- for U.S.A.

operate a service bureau or for any other use

 

involving the processing of data for other per-

 

THIS IS A LEGAL AGREEMENT BETWEEN

sons or entities.

 

YOU, AS THE END USER, AND PIONEER

Pioneer and its licensor(s) shall retain all copy-

 

ELECTRONICS (USA) INC. (“PIONEER”).

right, trade secret, patent and other proprie-

 

PLEASE READ THE TERMS AND CONDI-

tary ownership rights in the Software. The

 

TIONS OF THIS AGREEMENT CAREFULLY BE-

Software is copyrighted and may not be cop-

 

FORE USING THE SOFTWARE INSTALLED ON

ied, even if modified or merged with other pro-

 

THE PIONEER PRODUCTS. BY USING THE

ducts. You shall not alter or remove any

 

SOFTWARE INSTALLED ON THE PIONEER

copyright notice or proprietary legend con-

 

PRODUCTS, YOU AGREE TO BE BOUND BY

tained in or on the Software.

 

THE TERMS OF THIS AGREEMENT. THE SOFT-

You may transfer all of your license rights in

 

WARE INCLUDES A DATABASE LICENSED BY

the Software, the related documentation and a

 

THIRD PARTY SUPPLIER( S) (“SUPPLIERS”),

copy of this License Agreement to another

 

AND YOUR USE OF THE DATABASE IS COV-

party, provided that the party reads and agrees

 

ERED BY THE SUPPLIERS’ SEPARATE

to accept the terms and conditions of this Li-

 

TERMS, WHICH ARE ATTACHED TO THIS

cense Agreement.

 

AGREEMENT (Refer to Terms and Conditions

2 DISCLAIMER OF WARRANTY

 

for the Tele Atlas Data). IF YOU DO NOT AGREE

 

The Software and related documentation are

 

WITH ALL OF THESE TERMS, PLEASE RE-

 

provided to you “AS IS”. PIONEER AND ITS LI-

 

TURN THE PIONEER PRODUCTS (INCLUDING

 

CENSOR(S) (for the purpose of provisions 2

 

THE SOFTWARE, AND ANY WRITTEN MATERI-

 

and 3, Pioneer and its licensor(s) shall be col-

 

ALS) WITHIN FIVE (5) DAYS OF RECEIPT OF

 

lectively referred to as “Pioneer”) MAKES AND

 

THE PRODUCTS, TO THE AUTHORIZED

 

YOU RECEIVE NO WARRANTY FOR THE SOFT-

 

PIONEER DEALER FROM WHICH YOU PUR-

 

WARE, WHETHER EXPRESS OR IMPLIED,

 

CHASED THEM. USE OF THE SOFTWARE

 

AND ALL WARRANTIES OF MERCHANTABIL-

 

SHALL BE DEEMED TO BE YOUR CONSENT

 

ITY AND FITNESS FOR ANY PARTICULAR

 

TO THE LICENSE AGREEMENT.

 

PURPOSE FOR THE SOFTWARE ARE EX-

 

 

 

1

GRANT OF LICENSE

PRESSLY EXCLUDED. SOME STATES DO NOT

 

Pioneer grants to you a non-transferable, non

ALLOW EXCLUSION OF IMPLIED WARRAN-

 

exclusive license to use the software installed

TIES, SO THE ABOVE EXCLUSION MAY NOT

 

on the Pioneer products (the “Software”) and

APPLY TO YOU. The Software is complex and

 

the related documentation solely for your own

may contain some nonconformities, defects or

 

personal use or for internal use by your busi-

errors. Pioneer does not warrant that the Soft-

 

ness, only on such Pioneer products.

ware will meet your needs or expectations,

 

You shall not copy, reverse engineer, translate,

that operation of the Software will be error free

 

port, modify or make derivative works of the

or uninterrupted, or that all non-conformities

 

Software. You shall not loan, rent, disclose,

can or will be corrected. Furthermore, Pioneer

 

publish, sell, assign, lease, sublicense, market

does not make any representations or warran-

 

or otherwise transfer the Software or use it in

ties regarding the use or results of the use of

 

any manner not expressly authorized by this

the Software in terms of its accuracy, reliability

 

agreement. You shall not derive or attempt to

or otherwise.

 

derive the source code or structure of all or

 

 

any portion of the Software by reverse engineering, disassembly, decompilation, or any

10 En

Introduction

3 LIMITATION OF LIABILITY

IN NO EVENT SHALL PIONEER BE LIABLE FOR ANY DAMAGES, CLAIM OR LOSS INCURRED BY YOU (INCLUDING, WITHOUT LIMITATION, COMPENSATORY, INCIDENTAL, INDIRECT, SPECIAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES, LOST PROFITS, LOST INCOME, LOST SALES OR BUSINESS, EXPENDITURES, INVESTMENTS, OR COMMITMENTS IN CONNECTION WITH ANY BUSINESS, LOSS OF ANY GOODWILL, OR DAMAGES) RESULTING FROM THE USE OF OR INABILITY TO USE THE SOFTWARE, EVEN IF PIONEER HAS BEEN INFORMED OF, KNEW OF, OR SHOULD HAVE KNOWN OF THE LIKELIHOOD OF SUCH DAMAGES. THIS LIMITATION APPLIES TO ANY AND ALL CAUSES OF ACTION INDIVIDUALLY OR IN THE AGGREGATE, INCLUDING WITHOUT LIMITATION BREACH OF CONTRACT, BREACH OF WARRANTY, NEGLIGENCE, STRICT LIABILITY, MISREPRESENTATION, AND OTHER TORTS. IF PIONEER’S WARRANTY DISCLAIMER OR LIMITATION OF LIABILITY SET FORTH IN THIS AGREEMENT SHALL OR FOR ANY REASON WHATSOEVER BE HELD UNENFORCEABLE OR INAPPLICABLE, YOU AGREE THAT PIONEER’S LIABILITY SHALL NOT EXCEED FIFTY PERCENT (50%) OF THE PRICE PAID BY YOU FOR THE ENCLOSED PIONEER PRODUCT.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty disclaimer and limitation of liability shall not be applicable to the extent that they are prohibited by any applicable federal, state or local law which provides that such a disclaimer or limitation cannot be waived or preempted.

4 EXPORT LAW ASSURANCES

You agree and certify that neither the Software nor any other technical data received from Pioneer, nor the direct product thereof, will be exported outside the United States except as authorized and as permitted by the laws and

regulations of the United States. If the Software has been rightfully obtained by you outside of the United States, you agree that you will not re-export the Software nor any other technical data received from Pioneer, nor the direct product thereof, except as permitted by the laws and regulations of the United States and the laws and regulations of the jurisdiction in which you obtained the Software.

5 TERMINATION

This Agreement is effective until terminated. You may terminate it at any time by destroying the Software. The Agreement also will terminate if you do not comply with any terms or conditions of this Agreement. Upon such termination, you agree to destroy the Software.

6 U.S. GOVERNMENT END USERS

If the Software is being acquired by or on behalf of the United States government or any other entity seeking or applying rights similar to those customarily claimed by the United States government, the Data is licensed with “Limited Rights”. Utilization of the Software is subject to the restrictions specified in the “Rights in Technical Data” clause at DFARS 252.227-7013, or the equivalent clause for nondefense agencies. Pioneer Electronics (USA) Inc., 2265 East 220th Street, Long Beach, CA 90810.

7 MISCELLANEOUS

This is the entire Agreement between Pioneer and you regarding its subject matter. No change in this Agreement shall be effective unless agreed to in writing by Pioneer. Pioneer retailers do not have the authority to change this Agreement. This Agreement shall be governed by and construed in accordance with the internal laws of the State of California. If any provision of this Agreement is declared invalid or unenforceable, the remaining provisions of this Agreement shall remain in full force and effect.

Chapter

01

Introduction

En 11

Chapter

01 Introduction

PIONEER AVIC-Z110BT- for Canada

THIS IS A LEGAL AGREEMENT BETWEEN YOU, AS THE END USER, AND PIONEER ELECTRONICS OF CANADA, INC.

(“PIONEER”). PLEASE READ THE TERMS AND CONDITIONS OF THIS AGREEMENT CAREFULLY BEFORE USING THE SOFTWARE INSTALLED ON THE PIONEER PRODUCTS. BY USING THE SOFTWARE INSTALLED ON THE PIONEER PRODUCTS, YOU AGREE TO BE BOUND BY THE TERMS OF THIS AGREEMENT. THE SOFTWARE INCLUDES A DATABASE LICENSED BY THIRD PARTY SUPPLIER

(S) (“SUPPLIERS”), AND YOUR USE OF THE DATABASE IS COVERED BY THE SUPPLIERS’ SEPARATE TERMS, WHICH ARE ATTACHED TO THIS AGREEMENT (Refer to page 14). IF YOU DO NOT AGREE WITH ALL OF THESE TERMS, PLEASE RETURN THE PIONEER PRODUCTS (INCLUDING THE SOFTWARE, AND ANY WRITTEN MATERIALS) WITHIN FIVE (5) DAYS OF RECEIPT OF THE PRODUCTS, TO THE AUTHORIZED PIONEER DEALER FROM WHICH YOU PURCHASED THEM. USE OF THE SOFTWARE SHALL BE DEEMED TO BE YOUR CONSENT TO THE LICENSE AGREEMENT.

1 GRANT OF LICENSE

Pioneer grants to you a non-transferable, non exclusive license to use the software installed on the Pioneer products (the “Software”) and the related documentation solely for your own personal use or for internal use by your business, only on such Pioneer products.

You shall not copy, reverse engineer, translate, port, modify or make derivative works of the Software. You shall not loan, rent, disclose, publish, sell, assign, lease, sublicense, market or otherwise transfer the Software or use it in any manner not expressly authorized by this agreement. You shall not derive, or attempt to derive, the source code or structure of all or any portion of the Software by reverse engineering, disassembly, decompilation, or any other means. You shall not use the Software to

operate a service bureau or for any other use involving the processing of data for other persons or entities.

Pioneer and its licensor(s) shall retain all copyright, trade secret, patent and other proprietary ownership rights in the Software. The Software is copyrighted and may not be copied, even if modified or merged with other products. You shall not alter or remove any copyright notice or proprietary legend contained in or on the Software.

You may transfer all of your license rights in the Software, the related documentation and a copy of this License Agreement to another party, provided that the party reads and agrees to accept the terms and conditions of this License Agreement.

2 DISCLAIMER OF WARRANTY

The Software and related documentation are provided to you “AS IS”. PIONEER AND ITS LICENSOR(S) (for the purpose of provisions 2 and 3, Pioneer and its licensor(s) shall be collectively referred to as “Pioneer”) MAKES AND YOU RECEIVE NO WARRANTY FOR THE SOFTWARE, WHETHER EXPRESS OR IMPLIED, AND ALL WARRANTIES OF MERCHANTABILITY AND FITNESS FOR ANY PARTICULAR PURPOSE FOR THE SOFTWARE ARE EXPRESSLY EXCLUDED. SOME STATES DO NOT ALLOW EXCLUSION OF IMPLIED WARRANTIES, SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU. The Software is complex and may contain some nonconformities, defects or errors. Pioneer does not warrant that the Software will meet your needs or expectations, that operation of the Software will be error free or uninterrupted, or that all non-conformities can or will be corrected. Furthermore, Pioneer does not make any representations or warranties regarding the use or results of the use of the Software in terms of its accuracy, reliability or otherwise.

12 En

Introduction

3 LIMITATION OF LIABILITY

IN NO EVENT SHALL PIONEER BE LIABLE FOR ANY DAMAGES, CLAIM OR LOSS INCURRED BY YOU (INCLUDING, WITHOUT LIMITATION, COMPENSATORY, INCIDENTAL, INDIRECT, SPECIAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES, LOST PROFITS, LOST SALES OR BUSINESS, EXPENDITURES, INVESTMENTS, OR COMMITMENTS IN CONNECTION WITH ANY BUSINESS, LOSS OF ANY GOODWILL, OR DAMAGES) RESULTING FROM THE USE OF OR INABILITY TO USE THE SOFTWARE, EVEN IF PIONEER HAS BEEN INFORMED OF, KNEW OF, OR SHOULD HAVE KNOWN OF THE LIKELIHOOD OF SUCH DAMAGES. THIS LIMITATION APPLIES TO ALL CAUSES OF ACTION IN THE AGGREGATE, INCLUDING WITHOUT LIMITATION BREACH OF CONTRACT, BREACH OF WARRANTY, NEGLIGENCE, STRICT LIABILITY, MISREPRESENTATION, AND OTHER TORTS. IF PIONEER’S WARRANTY DISCLAIMER OR LIMITATION OF LIABILITY SET FORTH IN THIS AGREEMENT SHALL OR FOR ANY REASON WHATSOEVER BE HELD UNENFORCEABLE OR INAPPLICABLE, YOU AGREE THAT PIONEER’S LIABILITY SHALL NOT EXCEED FIFTY PERCENT (50%) OF THE PRICE PAID BY YOU FOR THE ENCLOSED PIONEER PRODUCT.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty disclaimer and limitation of liability shall not be applicable to the extent that they are prohibited by any applicable federal, state or local law which provides that such a disclaimer or limitation cannot be waived or preempted.

4 EXPORT LAW ASSURANCES

You agree and certify that neither the Software nor any other technical data received from Pioneer, nor the direct product thereof, will be exported outside Canada except as authorized and as permitted by the laws and regulations of Canada. If the Software has been rightfully

obtained by you outside of Canada, you agree that you will not re-export the Software nor any other technical data received from Pioneer, nor the direct product thereof, except as permitted by the laws and regulations of Canada and the laws and regulations of the jurisdiction in which you obtained the Software.

5 TERMINATION

This Agreement is effective until terminated. You may terminate it at any time by destroying the Software. The Agreement also will terminate if you do not comply with any terms or conditions of this Agreement. Upon such termination, you agree to destroy the Software.

6 MISCELLANEOUS

This is the entire Agreement between Pioneer and you regarding its subject matter. No change in this Agreement shall be effective unless agreed to in writing by Pioneer. Pioneer retailers do not have the authority to change this Agreement. This Agreement shall be governed by and construed in accordance with the internal laws of the Province of Ontario and the federal laws of Canada applicable therein. If any provision of this Agreement is declared invalid or unenforceable, the remaining provisions of this Agreement shall remain in full force and effect.

Chapter

01

Introduction

En 13

Chapter

01 Introduction

Terms and Conditions for the Tele Atlas Data

THIS IS A LEGAL AGREEMENT (THE “AGREEMENT”) BETWEEN YOU, THE END USER, AND TELE ATLAS NORTH AMERICA, INC. (“Tele Atlas”). BY USING YOUR COPY OF THE TELE ATLAS DATA, YOU AGREE TO THE TERMS AND CONDITIONS OF THIS AGREEMENT.

1 Grant of License.

Tele Atlas grants you a non-transferable, nonexclusive license to use the map data and business points of interest information (the “POIs”), (together, the “Data”) contained on these discs, solely for personal, non-commer- cial use and not to operate a service bureau or for any other use involving the processing of data of other persons or entities. You may make one (1) copy of the Data for archival or backup purposes only but you may not otherwise copy, reproduce, modify, make derivative works, derive the structure of or reverse engineer the Data. The Data contains confidential and proprietary information and materials, and may contain trade secrets, so you agree to hold the Data in confidence and in trust and not to disclose the Data or any portions in any form, including by renting, leasing, publishing, leasing, sublicensing or transferring the Data to any third party. You are prohibited from removing or obscuring any copyright, trademark notice or restrictive legend.

2 Ownership.

The Data is copyrighted by Tele Atlas and its licensors and they retain all ownership rights in the Data. You agree not to alter, remove, obliterate, or obscure any copyright notice or proprietary legend contained in or on the Data.

3 Warranty Disclaimer.

THE DATA IS PROVIDED ON AN “AS IS” AND “WITH ALL FAULTS BASIS” AND TELE ATLAS AND ITS SUPPLIERS EXPRESSLY DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MER-

CHANTABILITY, SATISFACTORY QUALITY, ACCURACY, TITLE AND FITNESS FOR A PARTICULAR PURPOSE. NO ORAL OR WRITTEN ADVICE OR INFORMATION PROVIDED BY TELE ATLAS OR ANY OF ITS AGENTS, EMPLOYEES OR THIRD PARTY PROVIDERS SHALL CREATE A WARRANTY, AND YOU ARE NOT ENTITLED TO RELY ON ANY SUCH ADVICE OR INFORMATION. THIS DISCLAIMER OF WARRANTIES IS AN ESSENTIAL CONDITION OF THE AGREEMENT.

4 Limitation of Liability.

TELE ATLAS SHALL NOT BE LIABLE TO YOU FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, INDIRECT OR EXEMPLARY DAMAGES ARISING OUT OF THIS AGREEMENT, INCLUDING LOST PROFITS OR COSTS OF COVER, LOSS OF USE OR BUSINESS INTERRUPTION OR THE LIKE, REGARDLESS OF WHETHER YOU WERE ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOTWITHSTANDING ANYTHING TO THE CONTRARY CONTAINED HEREIN, TELE ATLAS SHALL HAVE NO MONETARY LIABILITY TO YOU FOR ANY CAUSE (REGARDLESS OF THE FORM OF ACTION) UNDER OR RELATING TO THIS AGREEMENT.

5 Termination.

This Agreement will terminate immediately and automatically, without notice, if you breach any term of this Agreement. You agree that in the event of termination of the Agreement, you shall return the Data (including all documentation and all copies) to Tele Atlas and its suppliers.

14 En

 

Chapter

Introduction

01

 

 

6 Indemnity.

You agree to indemnify, defend and hold Tele Atlas, its Licensors, and its Suppliers (including their respective licensors, suppliers, assignees, subsidiaries, affiliated companies, and the respective officers, directors, employees, shareholders, agents and representatives) free and harmless from and against any liability, loss, injury (including injuries resulting in death), demand, action, cost, expense, or claim of any kind or character, including but not limited to attorney’s fees, arising out of or in connection with any use or possession by you of the Data.

7 U.S. Government Rights.

If you are an agency, department, or other entity of the United States Government, or funded in whole or in part by the United States Government, then use, duplication, reproduction, release, modification, disclosure or transfer of this commercial product and accompanying documentation, is restricted in accordance with the LIMITED or RESTRICTED rights as described in DFARS 252.227-7014(a)

(1) (JUN 1995) (DOD commercial computer software definition), DFARS 227.7202-1 (DOD policy on commercial computer software), FAR 52.227-19 (JUN 1987) (commercial computer software clause for civilian agencies), DFARS 252.227-7015 (NOV 1995) (DOD technical data – commercial items clause); FAR 52.227-14 Alternates I, II, and III (JUN 1987) (civilian agency technical data and noncommercial computer software clause); and/or FAR 12.211 and FAR 12.212 (commercial item acquisitions), as applicable. In case of conflict between any of the FAR and DFARS provisions listed herein and this License, the construction that provides greater limitations on the Government’s rights shall control. Contractor/ manufacturer is Tele Atlas North America, Inc., 11 Lafayette Street, Lebanon, NH 037661445. Phone: 603.643. 0330. The Data is ©1984-2008 by Tele Atlas. ALL RIGHTS RESERVED. For purpose of any public disclosure provision under any federal, state or local law,

it is agreed that the Data is a trade secret and a proprietary commercial product and not subject to disclosure.

If you are an agency, department, or other entity of any State government, the United States Government or any other public entity or funded in whole or in part by the United States Government, then you hereby agree to protect the Data from public disclosure and to consider the Data exempt from any statute, law, regulation, or code, including any Sunshine Act, Public Records Act, Freedom of Information Act, or equivalent, which permits public access and/or reproduction or use of the Data. In the event that such exemption is challenged under any such laws, this Agreement shall be considered breached and any and all right to retain any copies or to use of the Data shall be terminated and considered immediately null and void. Any copies of the Data held by you shall immediately be destroyed. If any court of competent jurisdiction considers this clause void and unenforceable, in whole or in part, for any reason, this Agreement shall be considered terminated and null and void, in its entirety, and any and all copies of the Data shall immediately be destroyed.

8 Additional Provisions with respect to POI Data only.

aNo Creation of Mailing Lists.

You are prohibited from using the POIs (i) to create mailing lists or (ii) for other such similar uses.

bCompliance.

You will use the POIs in compliance with all applicable federal, state and local laws, rules and regulations.

cIndemnification.

You shall indemnify and hold infoUSA, Inc. harmless against all third party claims or liability which are based in whole or in part of the users failure to comply with such laws, rules and regulations or which result from the use of the POIs through you.

dWarranty.

Introduction

En 15

Chapter

01 Introduction

In addition to the Warranties contained in the Agreement, YOU UNDERSTAND THAT THE POIS ARE LICENSED ON AN “AS IS” BASIS WITHOUT GUARANTEE, AND THERE ARE NO OTHER WARRANTIES MADE WHETHER, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY EXPRESS OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

ePOIs Segregation.

You are prohibited from combining or merging the POIs with any other POI data. The POIs shall be maintained in such a way that they are separately identifiable from all other POI data at all times.

9 Agreement in English.

The parties hereto confirm that they have requested that this Agreement and all attachments and related documents be drafted in English.

Les parties ont exigé que le présent contrat et tous les documents attachés soient rédigés en Anglais.

10 Miscellaneous.

This is the exclusive and complete Agreement between Tele Atlas and you regarding its subject matter. Nothing in this Agreement shall create a joint venture, partnership or principalagent relationship between Tele Atlas and you. The internal laws of California shall govern this Agreement and you consent to the jurisdiction of the Northern District of California or the State of California for the County of Santa Clara. Sections 2 – 10 shall survive the expiration or termination of this Agreement. This Agreement may be amended, altered, or modified only by Tele Atlas. You may not assign any part of this Agreement without Tele Atlas’ prior written consent. You acknowledge and understand that the Data may be subject to restrictions on exportation and agree to comply with any applicable export laws. In the event that any provision or part of a provision of this Agreement is determined to be invalid, illegal,

or unenforceable, such provision or part thereof shall be stricken from this Agreement and the remainder of this Agreement shall be valid, legal, and enforceable to the maximum extent possible. Any notice under this Agreement shall be delivered by courier to Tele Atlas North America, Inc., Attention Contracts Department, 11 Lafayette Street, Lebanon, NH 03766 USA. The covenants and obligations undertaken by you herein are intended for the direct benefit of Tele Atlas and may be enforced by Tele Atlas directly against you.

16 En

Introduction

Licenses

Chapter

01

Introduction

En 17

Chapter

01 Introduction

18 En

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Chapter

Introduction

01

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Introduction

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

En 19

Chapter

 

 

 

 

 

 

01

 

Introduction

 

 

 

 

 

 

 

 

 

 

 

 

About the database

Copyright Notices for North

 

About the Data for the Map

American data

 

1 Tele Atlasâ MultiNetâ USA and Canada data.

 

Database

 

As of the Effective Date, the copyright notice

 

! Modifications related to roads, streets/high-

 

for Tele Atlasâ MultiNetâ USA and Canada is:

 

 

ways, terrain, construction and other things

NOTICE

 

 

before/during the development period may

 

 

ã 2006 – 2008 Tele Atlas. All rights reserved.

 

 

not be reflected in this database. Inevitably,

 

 

This material is proprietary and the subject of

 

 

those modifications after that period are

 

 

copyright protection and other intellectual

 

 

not reflected in this database.

 

 

property rights owned or licensed to Tele

 

! For more details about the map coverage of

 

Atlas. Tele Atlas is an authorized distributor of

 

 

this navigation system, refer to the informa-

 

 

selected Statistics Canada computer files

 

 

tion on our website.

 

 

under Agreement number 6776. The product

 

! It is strictly prohibited to reproduce and use

 

includes information copied with permission

 

 

any part or the whole of this map in any

 

 

from Canadian authorities, including ã Cana-

 

 

form without permission from the copyright

 

 

da Post Corporation and GeoBaseâ, and De-

 

 

owner.

partment of Natural Resources Canada, All

 

! If the local traffic regulations or conditions

 

rights reserved. The product is sourced in part

 

 

deviate from this data, follow the local traf-

 

 

from Geography Division, Statistics Canada,

 

 

fic regulations (such as signs, indications,

 

 

2006 Road Network File (RNF), 92-500-XWE/

 

 

etc.) and conditions (such as construction,

 

 

XWF. The incorporation of data sources from

 

 

weather, etc.).

 

 

Statistics Canada within this product shall not

 

! The traffic regulation data used in the map

 

be construed as constituting an endorsement

 

 

database applies only to standard sized

 

 

by Statistics Canada of such product. The use

 

 

passenger vehicles. Note that regulations

 

 

of this material is subject to the terms of a Li-

 

 

for larger vehicles, motorbikes, and other

 

 

cense Agreement. You will be held liable for

 

 

non-standard vehicles are not included in

 

 

any unauthorized copying or disclosure of this

 

 

the database.

 

 

material.

 

 

 

 

 

 

2 As of the Effective Date, the copyright notice

 

 

 

for all third-party brand icons (the “Brand

 

 

 

Icons”) are located in the operator’s manual

 

 

 

included in the Licensed Products.

 

 

 

3 As of the Effective Date, the copyright notice

 

 

 

with logo for infoUSA, Inc. is:

 

 

 

Data by

 

 

 

 

 

 

 

 

 

 

Copyright C 2009

 

 

 

All Rights Reserved

 

 

 

4 As for Map Version, Tele Atlas. Rel. 07/2008.

20 En

Chapter

Introduction

Important Safety Information

morning only, but you arrive later, it would be

 

 

against the traffic regulations so you cannot

 

 

 

WARNING

drive along the set route. When driving, please

! Do not attempt to install or service your navi-

follow the actual traffic signs. Also, the system

gation system by yourself. Installation or servi-

may not know some traffic regulations.

cing of the navigation system by persons

Before using your navigation system, be sure

without training and experience in electronic

to read and fully understand the following

equipment and automotive accessories may

safety information:

be dangerous and could expose you to the

p Read the entire manual before operating

risk of electric shock or other hazards.

this navigation system.

! If liquid or foreign matter should get inside

p The navigation features of your navigation

this navigation system, park your vehicle to

system (and rear view camera option if pur-

safe place and turn the ignition switch off

chased) are intended solely as an aid to

(ACC OFF) immediately and consult your deal-

you in the operation of your vehicle. It is

er or the nearest authorized Pioneer Service

not a substitute for your attentiveness,

Station. Do not use the navigation system in

judgment, and care when driving.

this condition because doing so may result in

p Do not operate this navigation system (or

a fire, electric shock, or other failure.

the rear view camera option if purchased) if

! If you notice smoke, a strange noise or odor

doing so will divert your attention in any

from the navigation system, or any other ab-

way from the safe operation of your vehicle.

normal signs on the LCD screen, turn off the

Always observe safe driving rules and fol-

power immediately and consult your dealer or

low all existing traffic regulations. If you ex-

the nearest authorized Pioneer Service Sta-

perience difficulty in operating the system

tion. Using this navigation system in this con-

or reading the display, park your vehicle in

dition may result in permanent damage to the

a safe location and apply the parking brake

system.

before making the necessary adjustments.

! Do not disassemble or modify this navigation

p Never allow others to use the system un-

system, as there are high-voltage components

less they have read and understood the op-

inside which may cause an electric shock. Be

erating instructions.

sure to consult your dealer or the nearest

p Never use this navigation system to route

authorized Pioneer Service Station for internal

to hospitals, police stations or similar facil-

inspection, adjustments or repairs.

ities in an emergency. Stop using any func-

! Do not allow this product to come into contact

tions relating to the hands-free phone and

with liquids. Electrical shock could result.

please call 911.

Also, damage to the product, smoke, and over-

p Route and guidance information displayed

heating could result from contact with liquids.

by this equipment is for reference purposes

 

 

 

CAUTION

only. It may not accurately reflect the latest

 

permissible routes, road conditions, one

! When a route is calculated, the route and

way streets, road closures, or traffic restric-

voice guidance for the route are automatically

tions.

set. Also, for day or time traffic regulations,

p Traffic restrictions and advisories currently

only information about traffic regulations ap-

in force should always take precedence

plicable at the time when the route was calcu-

over guidance given by the navigation sys-

lated is shown. One-way streets and street

tem. Always obey current traffic restric-

closures may not be taken into consideration.

tions, even if the navigation system

For example, if a street is open during the

provides contrary advice.

 

 

01

Introduction

En 21

Chapter

 

 

 

 

01

 

Introduction

 

 

 

 

 

 

 

 

p Failure to set correct information about the

Additional Safety Information

 

 

local time may result in the navigation sys-

Parking brake interlock

 

 

tem providing improper routing and gui-

 

 

dance instructions.

Certain functions (such as viewing of DVD-

 

p Never set the volume of your navigation

Video and certain touch key operations) of-

 

 

system so high that you cannot hear out-

fered by this navigation system could be dan-

 

 

side traffic and emergency vehicles.

gerous and/or unlawful if used while driving.

 

p To promote safety, certain functions are dis-

To prevent such functions from being used

 

 

abled unless the vehicle is stopped and/or

while the vehicle is in motion, there is an inter-

 

 

the parking brake is applied.

lock system that senses when the parking

 

p The data encoded in the built-in memory is

brake is set and when the vehicle is moving. If

 

 

the intellectual property of the provider, and

you attempt to use the functions described

 

 

the provider is responsible for such con-

above while driving, they will become disabled

 

 

tent.

until you stop the vehicle in a safe place, and

 

p Keep this manual handy as a reference for

apply the parking brake. Please keep the brake

 

 

operating procedures and safety informa-

pedal pushed down before releasing the park-

 

 

tion.

ing brake.

 

p Pay close attention to all warnings in this

 

 

 

 

manual and follow the instructions care-

WARNING

 

 

fully.

 

 

! LIGHT GREEN LEAD AT POWER CON-

 

p Do not install this navigation system where

 

NECTOR IS DESIGNED TO DETECT

 

 

it may (i) obstruct the driver’s vision, (ii) im-

 

 

PARKED STATUS AND MUST BE CON-

 

 

pair the performance of any of the vehicle’s

 

 

NECTED TO THE POWER SUPPLY SIDE

 

 

operating systems or safety features, in-

 

 

OF THE PARKING BRAKE SWITCH. IM-

 

 

cluding air bags or hazard lamp buttons or

 

 

PROPER CONNECTION OR USE OF

 

 

(iii) impair the driver’s ability to safely oper-

 

 

THIS LEAD MAY VIOLATE APPLICABLE

 

 

ate the vehicle.

 

 

LAW AND MAY RESULT IN SERIOUS IN-

 

p Please remember to fasten your seat belt at

 

JURY OR DAMAGE.

 

 

all times while operating your vehicle. If

 

 

! To avoid the risk of damage and injury and the

 

 

you are ever in an accident, your injuries

 

 

potential violation of applicable laws, the navi-

 

 

can be considerably more severe if your

 

 

gation system is not for use with a “Video

 

 

seat belt is not properly buckled.

 

 

image” that is visible to the driver.

 

p Never use headphones while driving.

 

! In some countries or states the viewing of

 

 

 

 

 

 

“Video image” on a display inside a vehicle

 

“GOOG-411” service

even by persons other than the driver may be

 

p Pioneer does not bear responsibility for the

illegal. Where such regulations apply, they

 

must be obeyed.

 

 

accuracy of the information.

 

 

! When applying the parking brake in order to

 

p Pioneer does not bear responsibility for

 

view “Video image” or to enable other func-

 

 

changes to information services provided

 

 

tions offered by the navigation system, park

 

 

by related companies, such as cancellation

 

 

your vehicle in a safe place, and keep the

 

 

of services or changing to pay-services.

 

 

brake pedal pushed down before releasing the

 

 

Also, we do not accept return of the pro-

 

 

parking brake if the vehicle is parked on a hill

 

 

duct for this reason.

 

 

or otherwise might move when releasing the

 

 

 

 

 

 

parking brake.

22 En

 

Chapter

Introduction

01

 

 

CAUTION

Accuracy/performance of interlock may be impacted by such factors as GPS signal detection and driving habits or conditions of the place where the vehicle is parked.

When you attempt to watch “Video image” while driving, the warning “Viewing of front seat video source while driving is strictly prohibited.” will appear on the screen. To watch “Video image” on this display, stop the vehicle in a safe place and apply the parking brake. Please keep the brake pedal pushed down before releasing the parking brake.

WARNING

!SCREEN IMAGE MAY APPEAR REVERSED.

!USE INPUT ONLY FOR REVERSE OR MIRROR IMAGE REAR VIEW CAMERA. OTHER USE MAY RESULT IN INJURY OR DAMAGE.

CAUTION

!For safety reasons, the rear view camera function is not available until the navigation system boots up completely.

!The rear view mode is to use the navigation system as an aid to keep an eye on the trailers,

or while backing up. Do not use this function for entertainment purposes.

Introduction

When using a display connected to REAR MONITOR OUTPUT

The video output terminal (REAR MONITOR OUTPUT) is for connection of a display to enable passengers in the rear seats to watch video images.

WARNING

NEVER install the Rear Display in a location that enables the driver to watch video images while driving.

To avoid battery exhaustion

Be sure to run the vehicle engine while using this product. Using this product without running the engine can drain the battery.

WARNING

Do not use with vehicles that do not feature an ACC position.

Rear view camera

With an optional rear view camera, you are able to use the navigation system as an aid to keep an eye on trailers, or backing into a tight parking spot.

Notes Before Using the System

Important (Serial Number:)

The serial number of this device is located on the bottom of this product. For your own security and convenience, be sure to record this number on the enclosed warranty card.

Failure to operate

Should the navigation system fail to operate properly, contact your dealer or nearest authorized Pioneer Service Station.

En 23

Chapter

 

 

 

 

01

 

Introduction

 

 

 

 

 

 

 

 

 

 

Manual overview

 

After-sales service for Pioneer products

 

Please contact the dealer or distributor from

How to use this manual

 

which you purchased the product for after-

Finding the operation procedure for

 

sales service (including warranty conditions)

 

what you want to do

 

or any other information. In case the necessary

 

When you have decided what you want to do,

 

information is not available, please contact the

 

you can find the page you need from the

 

companies listed below.

 

“Contents”.

 

Please do not ship your product to the compa-

 

 

 

 

nies at the addresses listed below for repair

Finding the operation procedure from

 

without making advance contact.

 

a menu name

 

!

U.S.A

 

If you want to check the meaning of an item

 

 

Pioneer Electronics (USA) Inc.

 

 

displayed on the screen, you will find the ne-

 

 

CUSTOMER SUPPORT DIVISION

 

 

cessary page from the “Display information” at

 

 

P.O. Box 1760 Long Beach, CA 90801-1760

 

 

the end of the manual.

 

 

800-421-1404

 

 

 

 

 

!

CANADA

Glossary

 

 

Pioneer Electronics of Canada, Inc.

Use the glossary to find the meanings of

 

 

CUSTOMER SATISFACTION DEPARTMENT

terms.

 

 

300 Allstate Parkway Markham, Ontario

 

 

 

 

L3R 0P2

Terminology

 

 

1-877-283-5901

 

 

905-479-4411

Before moving on, take a few minutes to read

 

For warranty information, please see the Lim-

the following information about the conven-

 

ited Warranty sheet included with your pro-

tions used in this manual. Familiarity with

 

duct.

these conventions will help you greatly as you

 

 

 

learn how to use your new equipment.

 

 

 

 

Visit Our Web site

! Buttons on your navigation system are de-

 

scribed in ALL CAPITAL, BOLD lettering:

 

Visit us at the following site:

e.g.)

 

 

 

http://www.pioneerelectronics.com

 

MENU button, MAP button.

! Items in different menus, screen titles, and

In Canada

 

functional components are described in

http://www.pioneerelectronics.ca

 

 

bold with double quotation marks “ ”:

1 Register your product. We will keep the details

 

 

e.g.)

of your purchase on file to help you refer to

 

 

“Destination Menu” screen or “AV

this information in the event of an insurance

 

 

Source” screen

claim such as loss or theft.

 

!

Touch panel keys that are available on the

2 Receive updates on the latest products and

 

screen are described in bold in brackets [ ]:

technologies.

 

 

e.g.)

3 Download owner’s manuals, order product

 

 

[Destination], [Settings].

catalogs, research new products, and much

 

!

Extra information, alternatives and other

 

more.

notes are presented in the following for-

4 Receive notices of software upgrades and

mat:

software updates.

e.g.)

 

 

p If the home location has not been stored

 

yet, set the location first.

24 En

Introduction

! References are indicated like this:

Notice regarding DVD-

e.g.)

=For details, refer to How to use the navi- Video viewing

gation menu screens on page 34. This product incorporates copyright protection

Definitions of terminology

“Front Display” and “Rear Display”

In this manual, the screen that is attached to the body of this navigation unit will be referred to as the “Front Display”. Any additional optional screen that is purchased for use in conjunction with this navigation unit will be referred to as the “Rear Display”.

technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

Chapter

01

Introduction

“Video image”

“Video image” in this manual indicates moving images of DVD-Video, DivXâ, iPod, and any equipment that is connected to this system with an RCA cable, such as general-purpose AV equipment.

“External storage device (USB, SD)”

The SD memory card, SDHC memory card and USB memory device are collectively referred to as the “external storage device (USB, SD)”. If it indicates the USB memory only, it is referred to as the “USB storage device”.

“SD memory card”

The SD memory card and SDHC memory card are collectively referred to as the “SD memory card”.

Notice regarding video viewing

Remember that use of this system for commercial or public viewing purposes may constitute an infringement on the author’s rights as protected by the Copyright Law.

Notice regarding MP3 file usage

Supply of this navigation system conveys only a license for private, non-commercial use and does not convey a license nor imply any right to use this product in any commercial (i.e. rev- enue-generating), real time broadcasting (terrestrial, satellite, cable and/or any other media), broadcasting/streaming via internet, intranets and/or other networks or in other electronic content distribution systems, such as pay-audio or audio-on-demand applications. An independent license for such use is required. For details, please visit http://www.mp3licensing.com.

iPod compatibility

This product supports only the following iPod models and iPod software versions. Others may not work correctly.

!iPod nano first generation; Ver. 1.3.1

!iPod nano second generation; Ver. 1.1.3

!iPod nano third generation; Ver. 1.1.3

!iPod nano fourth generation; Ver. 1.0.3

!iPod fifth generation; Ver. 1.3

!iPod classic; Ver. 2.0.1

!iPod touch first generation; Ver. 2.2.1

!iPod touch second generation; Ver. 2.2.1

En 25

 

 

 

 

 

!

iPhone; Ver. 2.2.1

Notes on internal memory

!

iPhone 3G; Ver. 2.2.1

Before removing the vehicle

 

p In this manual, iPod and iPhone will be re-

 

 

ferred to as iPod.

battery

 

p When you use this navigation system with

If the battery is disconnected or discharged,

 

 

a Pioneer USB interface cable for iPod (CD-

 

 

the memory will be erased and must be repro-

 

 

IU50V) (sold separately), you can control an

 

 

gramed.

 

 

iPod compatible with this navigation sys-

 

 

p Some data remains. Read Returning the na-

 

 

tem.

 

 

vigation system to the default or factory set-

 

p To obtain maximum performance, we re-

 

tings before you operate this function.

 

 

commend that you use the latest software

 

 

= For more detailed information about the

 

 

for the iPod.

 

 

items which would be erased, refer to

 

p Operation methods may vary depending on

 

Returning the navigation system to the

 

 

the iPod models and the software version

 

 

default or factory settings on page 175.

 

 

of iPod.

 

 

 

 

 

p For more details about iPod compatibility

Data subject to erasure

 

 

with this navigation system, refer to the in-

 

 

formation on our website.

The information is erased by disconnecting

 

p iPod is a trademark of Apple Inc., regis-

the yellow lead from the battery (or removing

 

 

tered in the U.S. and other countries.

the battery itself). However, some items re-

 

p iPhone is a trademark of Apple Inc.

main.

 

 

 

p Some data remains. Read Returning the na-

 

Map coverage

vigation system to the default or factory set-

 

tings before you operate this function.

 

For more details about the map coverage of

= For more detailed information about the

Chapter

 

 

 

01

Introduction

 

 

this navigation system, refer to the information

items which would be erased, refer to

on our website.

Returning the navigation system to the default or factory settings on page 175.

Protecting the LCD panel and screen

pDo not allow direct sunlight to fall on the LCD screen when this product is not being used. Extended exposure to direct sunlight can result in LCD screen malfunction due to the resulting high temperatures.

pWhen using a cellular phone, keep the antenna of the cellular phone away from the LCD screen to prevent disruption of the

video in the form of spots, colored stripes, etc.

pTo protect the LCD screen from damage, be

sure to touch the touch panel keys with your finger and gently touch the screen.

26 En

Basic operation

Checking part names and functions

This chapter gives information about the names of the parts and the main features using the buttons.

Chapter

02

operation Basic

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7

6

5

4

3

2

1

8

9

1

LCD screen

 

 

 

3 TRK (c/d) button

 

 

2

OPEN CLOSE button

Press to perform manual seek tuning, fast

forward, reverse and track search controls.

 

 

En 27

Chapter

 

 

 

 

02

 

Basic operation

 

 

 

 

 

 

 

 

 

= For more details, refer to the descriptions

Adjusting the LCD panel angle

 

 

from Chapter 14 to Chapter 30.

 

 

 

4 MODE button

WARNING

 

When opening, closing and adjusting the angle

 

 

! Press to switch between the map screen

 

 

of the LCD panel, be careful not to get your finger

 

 

and the AV operation screen.

 

 

caught.

 

 

! Press to display the map screen while

 

 

 

 

 

 

the navigation function screen is dis-

CAUTION

 

 

played.

 

 

! Press and hold to display the “Picture

Do not open and close the LCD panel with hands

 

 

Adjustment” screen.

by force. This may cause malfunction.

 

 

= For details, refer to Operating the pic-

1 Press the OPEN CLOSE button.

 

 

ture adjustment on page 158.

 

 

The “Monitor Setup” screen appears.

 

 

 

 

5 HOME button

 

 

 

 

! Press the HOME button to display the

 

 

 

 

“Top Menu”.

 

 

 

 

! Press to switch between the “Classic

 

 

 

 

Menu” and the “Shortcut Menu” while

 

 

 

 

the “Top Menu” is displayed.

 

 

 

 

! Press and hold to turn off the screen dis-

 

 

 

 

play.

 

 

6 VOL (+/–) button

Adjusts the AV (Audio and Video) source volume.

7 VOICE button

Press the VOICE button to activate voice operations.

Press and hold the VOICE button to switch the AV source to mute.

8Disc loading slot

Insert a disc to play.

=For details concerning operations, refer to Inserting and ejecting a disc on this page.

9SD card slot

=For more detailed information, refer to In-

serting and ejecting an SD memory card on the next page.

2Touch or to adjust the angle.

3Touch .

pThe adjusted angle of the LCD panel will be memorized and the LCD panel will automa-

tically return to that angle the next time the LCD panel is opened or closed.

Inserting and ejecting a disc

WARNING

!When opening, closing and adjusting the angle of the LCD panel, be careful not to get your finger caught.

!Do not use with the LCD panel left open. If LCD panel is left open, it may result in injury in the event of an accident.

CAUTION

!Do not open and close the LCD panel with hands by force. This may cause malfunction.

28 En

 

Chapter

Basic operation

02

 

 

!Do not operate this navigation system until the LCD panel completely opens or closes. If this navigation system is operated while the LCD panel is opening or closing, the LCD panel may stop at that angle for safety.

!Do not place a glass or a can on this navigation system when the LCD panel is open. Doing so may break this navigation system.

Inserting a disc

1 Press the OPEN CLOSE button.

The “Monitor Setup” screen appears.

2 Touch [Open].

The LCD panel opens, and the disc loading slot appears.

3 Insert a disc into the disc loading slot.

pDo not insert anything other than a disc into the disc loading slot.

4 Press the OPEN CLOSE button.

The LCD panel closes.

Ejecting a disc

1Press the OPEN CLOSE button.

The “Monitor Setup” screen appears.

2Touch [Disc Eject].

The LCD panel opens, and the disc is ejected.

3 Press the OPEN CLOSE button.

The LCD panel closes.

Inserting and ejecting an SD memory card

CAUTION

!To prevent data loss and damage to the storage device, never remove it from this navigation system while data is being transferred.

!If data loss or corruption occurs on the storage device for any reason, it is usually not possible to recover the data. Pioneer accepts no liability for damages, costs or expenses arising from data loss or corruption.

!Do not press the OPEN CLOSE button when the SD memory card is not fully inserted. Doing so may damage the card.

!Do not press the OPEN CLOSE button before the SD memory card has been completely removed. Doing so may damage the card.

Press the middle of the SD memory card gently and pull out straight.

pThis system is not compatible with Multi Media Card (MMC).

pCompatibility with all SD memory cards is not guaranteed.

pThis unit may not achieve optimum performance with some SD memory cards.

Inserting an SD memory card

1 Press the OPEN CLOSE button.

The “Monitor Setup” screen appears.

operation Basic

En 29

Chapter

02 Basic operation

2 Touch [SD Insert].

The LCD panel opens, and the SD card slot appears.

3 Insert an SD memory card into the SD card slot.

Insert it with the label surface facing to the upside and press the card until it clicks and completely locks.

4 Press the OPEN CLOSE button.

The LCD panel closes, and then the navigation system restarts.

pIf the SD memory card only contains music files or video files, the navigation system will not be restarted.

2 Touch [Eject SD].

The following message appears.

3 Touch [Yes].

The navigation system restarts, and then the LCD panel opens.

4Press the SD memory card until it clicks.

5Pull out the SD memory card.

6Press the OPEN CLOSE button.

The LCD panel closes, and then the navigation system restarts.

Plugging and unplugging a USB storage device

CAUTION

Ejecting an SD memory card

1 Press the OPEN CLOSE button.

The “Monitor Setup” screen appears.

!To prevent data loss and damage to the storage device, never remove it from this navigation system while data is being transferred.

!If data loss or corruption occurs on the storage device for any reason, it is usually not possible to recover the data. Pioneer accepts no liability for damages, costs or expenses arising from data loss or corruption.

30 En

 

Chapter

Basic operation

02

 

 

Plugging in a USB storage device

% Plug a USB storage device into the USB connector.

USB connector

pA USB interface cable for iPod (CD-IU50V) (sold separately) is required for connection.

1 Pull out the USB storage device after checking that no data is being accessed.

operation Basic

USB storage device

pCompatibility with all USB storage device is not guaranteed.

This navigation system may not achieve optimum performance with some USB sto-

rage devices.

p Connection via USB hub is not possible.

Unplugging a USB storage device

% Pull out the USB storage device after checking that no data is being accessed.

USB connector

USB interface cable

 

for iPod

pFor more details about iPod compatibility with this navigation system, refer to the information on our website.

p Connection via USB hub is not possible.

2 Connect your iPod.

Connecting and disconnecting an iPod

CAUTION

!To prevent data loss and damage to the storage device, never remove it from this navigation system while data is being transferred.

!If data loss or corruption occurs on the storage device for any reason, it is usually not possible to recover the data. Pioneer accepts no liability for damages, costs or expenses arising from data loss or corruption.

Connecting your iPod

Using the USB interface cable for iPod enables you to connect your iPod to the navigation system.

Disconnecting your iPod

% Pull out the USB interface cable for iPod after checking that no data is being accessed.

Flow from startup to termination

1 Start the engine to boot up the system.

After a short pause, the splash screen comes on for a few seconds.

pTo protect the LCD screen from damage, be sure to touch the touch panel keys with your finger and gently touch the screen.

En 31

Chapter

02 Basic operation

2 Turn off the vehicle engine to terminate the system.

The navigation system is also turned off.

4 Read the disclaimer carefully, checking its details, and then touch [OK] if you agree to the conditions.

On first-time startup

When you use the navigation system for the first time, select the language that you want to use.

1Start the engine to boot up the system.

After a short pause, the splash screen comes on for a few seconds.

2Touch the language that you want to use on the screen.

3 Touch the language that you want to use for the voice guidance.

The navigation system will now restart.

Regular startup

% Start the engine to boot up the system.

After a short pause, the splash screen comes on for a few seconds.

pThe screen shown will differ depending on the previous conditions.

pWhen there is no route, the disclaimer appears after the navigation system reboots. Read the disclaimer carefully, checking its

details, and then touch [OK] if you agree to the conditions.

pIf the anti-theft function is activated, you must enter your password.

Read the disclaimer carefully, checking its

details, and then touch [OK] if you agree to the conditions.

32 En

 

Chapter

Basic operation

02

 

 

operation Basic

En 33

Chapter

03How to use the navigation menu screens

Screen switching overview

2

3

4

 

 

1

5

6

 

 

7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

34 En

 

Chapter

How to use the navigation menu screens

03

 

 

What you can do on each menu

1Top Menu

Press the HOME button to display the “Top Menu”.

This is the starting menu to access the desired screens and operate the various functions. There are two types of the “Top Menu”.

Classic Menu

Shortcut Menu

p In this manual, “Classic Menu” will be referred to as “Top Menu”.

2Destination Menu

You can search for your destination on this menu. You can also check or cancel your set route from this menu.

3Phone Menu

You can access the screen that is related to hands-free phoning to see call histories and change the settings on the Bluetooth wireless technology connection.

4AV Source menu

You can access the screen for selecting the audio and visual source to play.

5Settings Menu

You can access the screen to customize settings.

6Map screen

Press the MODE button to display the navigation map screen.

7AV operation screen

This is the screen that normally appears when you play the AV source. Touching the icon on the top left corner displays the “AV Source”

menu.

pTo return to the previous screen, touch

.

Operating list screens (e.g. POI list)

1 4 5

2

3

1Screen title

2

Touching or on the scroll bar scrolls through the list and allows you to view the re-

maining items.

3

Returns the previous screen.

4Listed items

Touching an item on the list allows you to narrow down the options and proceed to the next operation.

5

If all of the characters cannot be displayed within the displayed area, touching the key to

the right of the item allows you to see remaining characters.

Shortcut menu

Registering your favorite menu items in shortcuts allows you to quickly jump to the registered menu screen by a simple touch on the “Shortcut Menu” screen.

screens menu navigation the use to How

En 35

Chapter

03 How to use the navigation menu screens

Selecting the Shortcut

pUp to 15 menu items can be registered in shortcuts.

1Press the HOME button repeatedly to display the “Shortcut Menu” screen.

2Touch [Shortcut].

The Short-Cut Selection screen appears.

Scroll bar

3Touch the tab on the right edge or scroll the bar to display the icon that you want to set to shortcut.

4Touch and hold the icon that you want to add to shortcut.

5Move the icon to the left side of the screen, and then release it.

The selected item is added to shortcut.

Displaying the rear view camera image

Rear view image is displayed on the left-hand side of the screen, while the map of your surroundings is indicated on the right.

=For details, refer to Setting for rear view camera on page 99.

1Press the HOME button to display the “Top Menu”.

2Touch [Settings].

The “Settings Menu” screen appears.

3 Touch [System Settings].

The “System Settings” screen appears.

4 Touch [Back Camera].

The “Back Camera Settings” screen appears.

5 Touch [Camera] to turn it [On].

Canceling the Shortcut

1Touch and hold the icon that you want to cancel the shortcut.

2Move the icon to the right side of the screen, and then release it.

36 En

 

Chapter

How to use the map

04

 

 

Most of the information provided by your navigation system can be seen on the map. You need to become familiar with how information appears on the map.

How to read the map screen

This example shows an example of a 2D map screen.

 

 

 

1

 

 

 

 

 

 

 

 

 

 

h

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

g

 

 

 

 

 

 

 

 

 

 

 

2

 

 

 

 

 

 

 

 

 

 

f

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

e

 

 

 

 

 

 

 

 

 

 

 

3

 

 

 

 

 

 

 

 

 

 

d

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

c

 

 

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

 

 

 

b

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

a

5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7

 

8

9

p Information with the mark (*) appears only

p Touching this item enables you to hear

when the route is set.

the next guidance again.

p Depending on the conditions and settings,

4 Second Maneuver Arrow*

 

some items may not be displayed.

Shows the turning direction after next and the

1 Name of the street to be used (or next gui-

distance to there.

 

dance point)*

= For details, refer to Displaying maneu-

2 Next direction of travel*

vers on page 43.

 

When you approach a guidance point, this

5 Zoom in/Zoom out

 

item appears.

Touching

displays touch panel keys for

As you get closer to the guidance point, the

changing the map scale and the map orienta-

color of the item changes to green.

tion.

 

 

p Touching this item enables you to hear

6 Current position

 

the next guidance again.

Indicates the current location of your vehicle.

p You can select between display and

The apex of the triangular mark indicates your

non-display.

orientation and the display moves automati-

= For details, refer to Displaying man-

cally as you drive.

 

euvers on page 43.

p The apex of the triangular mark is the

3 Distance to the guidance point*

proper current position.

Shows the distance to the next guidance

7 Street name (or city name) that your vehi-

point.

cle is traveling along

 

map the use to How

En 37

Chapter

04 How to use the map

=For details, refer to Setting the current street name display on page 43.

8Extension tab for the AV information bar

Touching this tab opens the AV information bar and enables you to briefly view the current status on the AV source. Touching it again retracts the bar.

9Shortcut to the AV operation screen

The AV Source currently selected is shown. Touching the indicator displays the AV operation screen of the current source directly.

p If you connect your iPod to this navigation system, the artwork for the album that is playing appears.

aQuick Access icon

Displays Quick Access menu.

bMap orientation indicator

!When “North up” is selected, is displayed.

!When “Heading up” is selected, is displayed.

p The red arrow indicates north.

cCurrent route*

The route currently set is highlighted in bright color on the map. If a waypoint is set on the route, the route after the next waypoint is highlighted in another color.

dDirection line*

The direction towards your destination (next waypoint, or cursor) is indicated with a straight line.

eVoice icon

This icon shows when the voice operation is active.

fBluetooth Connected icon

This icon shows whether the device featuring Bluetooth technology is connected or not. You can select between display and non-display.

= For more details about “Selecting display or non-display for the Bluetooth Connected icon”, refer to Bluetooth Connected on page 43.

gMulti-Info window

Each touch of [Multi-Info window] changes the display information.

!Distance to the destination (or distance to waypoint)*

!Estimated time of arrival at your destination or waypoint*

The estimated time of arrival is an ideal value calculated based on the value set for [Speed] and the actual driving speed. The estimated time of arrival is only a reference value, and does not guarantee arrival at that time.

!Travel time to your destination or

waypoint* h Current time

Meaning of guidance flags

: Destination

The checkered flag indicates your destination.

: Waypoint

The blue flags indicate your waypoints.

: Guidance point

The next guidance point (next turning point, etc.) is shown by a yellow flag.

Displaying the AV information bar

You can check the current status on the selected AV source.

% Touch .

AV information bar appears.

# Touch the AV information bar. The AV information bar is retracted.

38 En

 

Chapter

How to use the map

04

 

 

Enlarged map of the intersection

When “Close Up View” in the “Map Settings” screen is “On”, an enlarged map of the intersection appears.

=For details, refer to Setting “Close Up View” on page 42.

Display during freeway driving

In certain locations of the freeway, lane information is available, indicating the recommended lane to be in to easily maneuver the next guidance.

1

While driving on the freeway, freeway exit numbers and freeway signs may be displayed when in the vicinity of interchanges and exits.

2 3

1 Lane information

2Freeway exit information

Displays the freeway exit.

3Freeway signs

These show the road number and give directional information.

pIf the data for these items is not contained in the built-in memory, the information is

not available even if there are the signs on the actual road.

Operating the map screen

Changing the scale of the map

You can change the map scale between 25 yard and 1 000 miles (25 meters and 2 000 kilometers).

1Display the map screen.

2Touch on the map screen.

and with the map scale appear.

3 Touch or to change the map scale.

pIf you do not operate the function for a few seconds, the display is automatically returned.

#Touch the direct scale key to change the map to the selected scale directly.

Switching the map orientation

You can switch the vehicle’s direction on the map between “Heading up” and “North up”. ! Heading up:

map the use to How

En 39

Chapter

04 How to use the map

The map display always shows the vehicle’s direction as proceeding toward the top of the screen.

! North up:

The map display always has north at the top of the screen.

pThe map orientation is fixed at “North up” in the following situation.

— When the map scale is 25 miles (50 kilo-

meters) or more.

pThe map orientation is fixed at “Heading up” in the following situation.

— When the 3D map screen is displayed.

1Display the map screen.

2Touch on the map screen.

or appears.

3 Touch or to switch the vehicle’s direction.

Each time you touch the key changes that setting.

pIf you do not operate the function for a few seconds, the display is automatically returned.

Scrolling the map to the position you want to see

1 Display the map screen.

2 Touch and drag the map in the desired direction to scroll.

1

2

1Cursor

2Distance from the current position

Positioning the cursor to the desired location results in a brief informational overview about the location being displayed at the bottom of screen, with street name and other information for this location being shown. (The information shown varies depending on the position.)

p The scrolling increment depends on your dragging length.

#Touch .

The map returns to the current position.

pPressing MODE button returns the map to the current position.

Quick Access

“Quick Access” allow you to perform various tasks, such as route calculation for the location indicated by the scroll cursor or registering a location in [Favorites], faster than using the navigation menu.

You can customize “Quick Access” displayed on screen. The “Quick Access” described here are prepared as the default setting.

= For details, refer to Selecting “Quick Access” on page 47.

pItems marked with an asterisk (*) cannot be removed from Quick Access menu.

40 En

 

Chapter

How to use the map

04

 

 

% When the map is displayed, touch .

= For details, refer to Calling a number in the

“Contacts List” on page 83.

[Close]

Hides the Quick Access menu.

Quick Access menu

: Route Options*

Displayed when the map is not scrolled. This item can be selected only during route guidance.

You can modify the conditions for route calculation and recalculate the current route.

= For details, refer to Modifying the route calculation conditions on page 53.

: Destination*

Displayed when the map is scrolled. Set the route to the place specified with the scroll cursor.

: Registration

Register information on the location indicated by the scroll cursor to “Favorites”.

=For details, refer to Registering a location by scroll mode on page 62.

: Vicinity Search

Find POIs (Points Of Interest) in the vicinity of the scroll cursor.

=For details, refer to Searching for a nearby POI on page 58.

: Overlay POI

Displays icons for surrounding facilities (POI) on the map.

map the use to How

=For details, refer to Displaying POI on the map on page 44.

: Volume

Displays the “Volume Settings” screen.

=For more details about “Volume”, refer to

Setting the Volume for Guidance and Phone

on page 98.

: Contacts

Displays the “Contacts List” screen.

En 41

Chapter

05 Customizing the map screen settings

The general settings related with a map screen can be customized.

To customize the map screen, display the

“Map Settings” screen.

1Display the “Top Menu” screen.

2Touch [Settings].

The “Settings Menu” screen appears.

3 Touch [Map Settings].

The “Map Settings” screen appears.

Setting the Item on the Map Screen

1Display the “Map Settings” screen.

2Touch [Displayed Info].

The “Displayed Information” screen appears.

Setting “Close Up View”

This setting enables switching to an enlarged map around the point where your vehicle is approaching an intersection, entrance/exit of freeway or a junction.

% Touch [Close Up View].

Each time you touch the key changes that setting.

![On] (default):

Switches to an enlarged map.

Displays the close up view with the 2D map.

![Off]:

Does not switch to an enlarged map.

City Map

You can select whether to display the city map when in certain metropolitan city areas.

pThe city map is displayed when the map scale is 0.05 mile (50 meters) or less.

% Touch [City Map].

Each time you touch the key changes that setting.

![On] (default):

Automatically switches to the city map when in a city map area.

![Off]:

Does not show the city map.

p Even if you switch [City Map] to [On], city map cannot display in areas where there is no city map data.

Setting the switching of the city map display

Sets whether to switch to the city map display when the vehicle is within a city map area.

% Touch [City Map Barrier].

Each time you touch the key changes that setting.

![On] (default):

Displays a city map when the vehicle enters the area of the city map.

![Off]:

42 En

 

Chapter

Customizing the map screen settings

05

 

 

Displays a city map when the area displayed on the map falls entirely within the city map area.

Show Traffic Incident

Selects whether to display or hide the traffic notification icons on the map when incidents occur on your route.

% Touch [Show Traffic Incident].

Each time you touch the key changes that setting.

![View] (default):

Displays the icons on the map.

![Hide]:

Hides the icons on the map.

=For details, refer to Checking traffic information manually on page 72.

Bluetooth Connected

Selects whether to display or hide the icon for current status of the phone connection via Bluetooth wireless technology.

% Touch [Bluetooth Connected].

Each time you touch the key changes that setting.

![View] (default):

Displays the Bluetooth Connected icon on the map.

![Hide]:

Hides the Bluetooth Connected icon on the map.

=For more details about “Bluetooth Connected icon”, refer to Bluetooth Connected icon on page 38.

Setting the current street name display

Selects whether to display or hide the street name (or city name) that your vehicle is traveling along.

% Touch [Current Street Name].

Each time you touch the key changes that setting.

![View] (default):

Displays the street name (or city name) on the map.

![Hide]:

Hides the street name (or city name) on the map.

Setting the Favorites icon display

You can select whether to display the “Favorites” icon on the map.

pFavorites icons are displayed when the map scale is 10 mile (20 kilometers) or less.

% Touch [Favorites Icon].

Each time you touch the key changes that setting.

![On] (default):

Displays the “Favorites” icon on the map.

![Off]:

Hides the “Favorites” icon on the map.

3D Land Mark

You can select whether to display the 3D Landmark on the map.

p3D Landmark only appears when the view mode is [3D View] and the map scale is set to 0.25 mile (200 m) or lower.

% Touch [3D Land Mark].

Each time you touch the key changes that setting.

![On] (default):

Displays the 3D Landmark on the map.

![Off]:

Hides the 3D Landmark on the map.

Displaying maneuvers

Selects whether to display or hide the next turn ahead of the vehicle on the map.

settings screen map the Customizing

En 43

Chapter

05 Customizing the map screen settings

% Touch [Show Manuever].

Each time you touch the key changes that setting.

![View] (default):

Displays the next turn ahead of the vehicle on the map.

![Hide]:

Hides the next turn ahead of the vehicle on the map.

MSN Direct

Selects whether to display or hide the received MSN Direct information on the map.

pFollowing informations are displayed:

Gas Prices

Movie Times

Local Events

pMSN Direct icons are not displayed when the map scale is 0.75 mile (1 kilometers) or more.

% Touch [MSN Direct].

Each time you touch the key changes that setting.

![On] (default):

Displays the icons on the map.

![Off]:

Hides the icons on the map.

Displaying POI on the map

Displays icons for the surrounding facilities (POI) on the map.

pPOI icons are not displayed when the map scale is 0.75 mile (1 kilometers) or more.

Displaying preinstalled POIs on the map

pYou can select up to 10 items from the detailed category.

1Display the “Map Settings” screen.

2Touch [Overlay POI].

The “Overlay POI” screen appears.

3 Touch [Display] to turn it [On].

pIf you do not want to display the POI icon on the map, touch [Display] to turn it [Off]. (Even if [Display] is turned [Off], the POI selection setting is retained.)

4 Touch [POI].

The “Overlay POI (Main Category)” screen appears.

5 Touch the category you want to display.

A list of subcategories under the selected main category appears.

# Touch [OK].

Returns previous screen.

6 Touch the subcategory.

A red check mark appears next to the selected category. To cancel the selection, touch the entry again.

44 En

 

Chapter

Customizing the map screen settings

05

 

 

# If you want to search with more detailed categories, touch [Detail].

Touch the item and touch [OK]. When only a few types of the detailed categories are selected, blue check marks will appear.

pWhen subcategory is selected, [Detail] is not available.

7Touch [OK].

Returns previous screen.

8To finish the selection, touch [OK].

Displaying the customized POIs

Creating a customized POI is possible by using the utility program “AVIC FEEDS” which is available separately, on your PC. (“AVIC FEEDS” will be available on our website.) Storing the customized POI properly and inserting the SD memory card enables the system to display the icons on the map screen.

pYou can select up to 10 items from the detailed category.

1Insert an SD memory card into the SD card slot.

=For more details of the operation, refer to Inserting and ejecting an SD memory card on page 29.

2Display the “Map Settings” screen.

3Touch [Overlay POI].

The “Overlay POI” screen appears.

4 Touch [Display] to turn it [On].

pIf you do not want to display the POI icon on the map, touch [Display] to turn it [Off]. (Even if [Display] is turned [Off], the POI selection setting is retained.)

5 Touch [Custom POI].

The list of POI categories appears.

6Touch the category you want to display.

7To finish the selection, touch [OK].

Switching the view mode

Various types of screen displays can be selected for navigation guidance.

2D map screen

settings screen map the Customizing

En 45

Chapter

05 Customizing the map screen settings

3D map screen

Street View

Rear View

1Display the “Map Settings” screen.

2Touch [View Mode].

The “View Mode” screen appears.

3 Touch the type that you want to set.

You can select the following types:

![2D View] (default): Displays the 2D map screen.

![3D View]:

Displays the 3D map screen.

![Street View]:

Displays the “Street View” screen.

p This type is available when the route is set.

![Rear View]:

Displays the rear view images.

pThis type is available when [Back Camera Settings] is set to [On].

=For details, refer to Setting for rear view camera on page 99.

Setting the map color change between day and night

To improve the visibility of the map during the evening, you can set the timing for changing the combination of the map color.

1Display the “Map Settings” screen.

2Touch [Day/Night Display].

Each time you touch the key changes that setting.

![Automatic] (default):

You can change the colors of a map between daytime and nighttime according to whether the vehicle lights are On or Off.

![Day]:

The map is always displayed with daytime

colors.

pTo use this function with [Automatic], the

Orange/white lead of the navigation system must be connected correctly.

Changing the road color

You can set the road color to bluish or reddish.

1Display the “Map Settings” screen.

2Touch [Road Color].

Each time you touch the key changes that setting.

![Blue] (default):

Changes to blue based road colors.

![Red]:

Changes to red based road colors.

46 En

 

Chapter

Customizing the map screen settings

05

 

 

Changing the setting of navigation interruption screen

Set whether to automatically switch to the navigation screen from the AV operation screen when your vehicle approaches a guidance point such as an intersection while displaying a screen other than navigation.

1Display the “Map Settings” screen.

2Touch [AV Guide Mode].

Each time you touch the key changes that setting.

![On] (default):

Switches from the audio operation screen to the navigation screen.

![Off]:

Does not switch the screen.

Selecting “Quick Access”

Select items to display on the map screen. In the list displayed on screen, the items with red checks are displayed on the map screen. Touch the item you want to display and then touch [OK] when a red check appears. You can select up to five items.

1Display the “Map Settings” screen.

2Touch [Quick Access Selection].

The “Quick Access Selection” screen appears.

3 Touch the item that you want to set in “Quick Access”.

You can select the following items:

pSettings marked with an asterisk (*) show that these are default or factory settings.

! : Registration*

Register information on the location indicated by the scroll cursor to “Favorites”.

=For details, refer to Registering a location by scroll mode on page 62.

! : Vicinity Search*

Find POIs (Points Of Interest) in the vicinity of the scroll cursor.

=For details, refer to Searching for a nearby POI on page 58.

! : Overlay POI*

Displays icon for surrounding facilities (POI) on the map.

=For details, refer to Displaying POI on the map on page 44.

! : Volume*

Displays the “Volume Settings” screen.

=For more details about “Volume”, refer to Setting the Volume for Guidance and Phone on page 98.

! : Contacts*

Displays the “Contacts List” screen.

=For details, refer to Calling a number in the “Contacts List” on page 83.

! : Whole Route Overview

Displays the entire route (currently set).

=For details, refer to Chapter 7.

! : Stock Info

Displays stock prices.

=For details, refer to Browsing stock quotes on page 76.

! : Traffic On Route

Displays a list of traffic information on the route.

=For details, refer to Checking traffic information on the route on page 71.

! : Traffic Events

Displays a list of traffic events information.

=For details, refer to Viewing the traffic event on page 70.

! : Day/Night Display

Switches Day/Night Display setting.

=For details, refer to Setting the map color change between day and night on the previous page.

! : Favorites Icon

Switches Favorites Icon setting.

=For details, refer to Setting the Favorites icon display on page 43.

4 To finish the setting, touch [OK].

settings screen map the Customizing

En 47

Chapter

06 Setting a route to your destination

CAUTION

For safety reasons, these route-setting functions are not available while your vehicle is in motion. To enable these functions, you must stop in a safe place and put on the parking brake before setting your route.

pSome information regarding traffic regulations depends on the time when the route calculation is performed. Thus, the information may not correspond with a certain traffic regulation when your vehicle actually passes through the location in question. Also, the information on the traffic regulations provided will be for a passenger vehicle, and not for a truck or other delivery vehicles. Always follow the actual traffic regulations when driving.

The basic flow of creating your route

1Park your vehicle in a safe place, and apply the parking brake.

2Display the “Top Menu” screen.

3Select the method of searching for your destination.

=For details, refer to Chapter 8.

4Enter the information about your destination to calculate route.

5Confirm the location on the map.

=For details, refer to Checking the location on the map on this page.

6The navigation system calculates the route to your destination, and then shows the route on the map.

7Check and decide the route.

=For details, refer to Checking the calculated route on this page.

8Your navigation system sets the route to your destination, and the map of your surroundings appears.

9After releasing the parking brake, drive in accordance with navigation guidance.

Checking the location on the map

After searching for the destination, the “Location confirmation screen” appears.

Location confirmation screen

% Touch [OK].

The destination is set, and then route calculation starts.

pIf you press MODE button during route calculation, the calculation is canceled and the map display appears.

#Touch [Scroll].

The map display changes to the scroll mode. You can fine-tune the location in the scroll mode, and then you can set the location as your destination or do various operations.

# Touch [Waypoint].

The location is added to the “Waypoints List” screen.

pIf a destination is not set, [Waypoint] is not available.

Checking the calculated route

After the destination is set, route calculation starts.

48 En

 

Chapter

Setting a route to your destination

06

 

 

When the route calculation is completed, “Route confirmation screen” appears.

Route confirmation screen

1 2 3 4

1Travel time to your destination

2Distance to the destination

3Estimated fuel cost to your destination

=For details, refer to Inputting the fuel consumption information for calculating the fuel cost on page 94.

4Route calculation condition

% Touch [OK].

Sets the displayed route as your route, and starts the route guidance.

# Touch .

The message confirming whether to cancel the calculated route appears.

Touch [Yes] to cancel the calculated route, and then the map screen appears.

Display multiple routes

You can select a desired route from multiple route options. Calculated routes are shown in different colors.

pIf you set waypoints, you cannot use the multiple route option.

1 Touch [Multiple Route].

The “Multiple Route Option” screen appears.

2Touch to .

Another route is displayed.

3Touch [OK].

“Route confirmation screen” appears.

Modifying the route calculation conditions

You can modify the conditions for route calculation and recalculate the current route.

1 Touch [Options] on the “Route confirmation screen”.

The “Route Options” screen appears.

2 Touch the desired items to change the route calculation conditions and then touch [OK].

The route is recalculated, and “Route confirmation screen” appears.

Items that users can operate

Settings marked with an asterisk (*) show that these are default or factory settings.

Route Condition

This setting controls how the route should be calculated by taking into account the time or the distance or the main road.

Determines which condition takes priority for route calculation.

[Fast]*:

Calculates a route with the shortest travel time to your destination as a priority.

[Short]:

Calculates a route with the shortest distance to your destination as a priority.

[Main Road]:

Calculate a route that passes major arterial road as a priority.

destination your to route a Setting

En 49

Chapter

06 Setting a route to your destination

Avoid Toll Road

This setting controls whether toll roads (including toll areas) should be taken into account.

[Off]*:

Calculate a route that may include toll roads (including toll areas).

[On]:

Calculate a route that avoids toll roads (including toll areas).

pThe system may calculate a route that includes toll road even if [On] is selected.

Avoid Ferry

This setting controls whether ferry crossings should be taken into account.

[Off]*:

Calculate a route that may include ferries.

[On]:

Calculate a route that avoids ferries.

pThe system may calculate a route that includes ferry way even if [On] is selected.

Avoid Freeway

This setting controls whether freeways may be included in the route calculation.

[Off]*:

Calculate a route that may include freeways.

[On]:

Calculate a route that avoids freeways.

pThe system may calculate a route that includes freeway even if [On] is selected.

Time restrictions

This setting controls whether streets or bridges have traffic restrictions during a certain time should be taken into account.

p If you want to set your route to avoid opened bridges, select [On].

[On]*:

Calculate a route while avoiding streets or bridges with traffic restrictions during a certain time.

[Off]:

Calculate a route while ignoring traffic restrictions.

pThe system may calculate a route that includes streets or bridges that are subject to traffic restrictions during a certain time even if [On] is selected.

CAUTION

If the time difference is not set correctly, the navigation system cannot consider traffic regulations correctly. Set the time difference correctly (=

Refer to Setting the time difference on page 97).

Learning Route

The system learns the travel history of your vehicle for each road.

This setting controls whether or not the travel history should be taken into account.

[On]*:

Calculate the route with the travel history taken into account.

[Off]:

Calculate the route without the travel history taken into account.

[Clear]:

Clear the current travel history.

Checking the current itinerary

You can check the route details.

% Touch [Profile] on the “Route confirmation screen”.

The “Route Profile” screen appears.

Adding a waypoint

Up to 5 waypoints can be set, and waypoints and final destination can be sorted automatically or manually.

50 En

 

Chapter

Setting a route to your destination

06

 

 

pWhen you set waypoints in the route to your destination, the route up to the next

waypoint will appear in light green. The rest of the route will appear in light blue.

=For details concerning operations, refer to

Adding a waypoint on the next page.

1 Touch [Waypoints] on the “Route confirmation screen”.

The “Waypoints List” screen appears.

2 Touch [Add].

The “Select Search method” screen appears.

3 Search for a location.

After searching for a point, display it on a map, then touch [OK] to add to the “Waypoints List” screen.

= For details, refer to Chapter 8.

4 Touch [OK] on the “Waypoints List” screen.

The route is recalculated, and “Route confirmation screen” appears.

destination your to route a Setting

En 51

Chapter

07 Checking and modifying the current route

You can check the route details. You can also recalculate the route in different conditions.

1Display the “Top Menu” screen.

2Touch [Destination].

The “Destination Menu” screen appears.

3 Touch [Route Overview].

The “Route Overview” screen appears.

Editing waypoints

You can edit waypoints (locations you want to visit on the way to your destination) and recalculate the route so that is passes through these locations.

To edit the waypoints, display the “Waypoints List” screen.

1Display the “Route Overview” screen.

2Touch [Waypoints].

The “Waypoints List” screen appears.

p[Route Overview] is active only when the route is set.

Checking the current itinerary

You can check the route details.

1Display the “Route Overview” screen.

2Touch [Profile].

The “Route Profile” screen appears.

pWhen a long distance route is calculated, your navigation system may not be able to list all roads. (In this case, the remaining

roads will be shown in the list as you drive on.)

Adding a waypoint

Up to 5 waypoints can be set, and waypoints and final destination can be sorted automatically or manually.

1Display the “Waypoints List” screen.

2Touch [Add].

The “Select Search method” screen appears.

3 Search for a location.

After searching for a point, display it on a map, then touch [OK] to add to the “Waypoints List” screen.

52 En

 

Chapter

Checking and modifying the current route

07

 

 

2 Touch [Sort].

The “Sort Waypoints” screen appears.

= For details, refer to Chapter 8.

4Touch [OK] on the “Waypoints List” screen.

The route is recalculated, and “Route confirmation screen” appears.

5Touch [OK].

The map of the current position appears.

Deleting a waypoint

You can delete waypoints from the route and then recalculate the route. (You can delete waypoints successively.)

1Display the “Waypoints List” screen.

2Touch [Delete] next to the waypoint that you want to delete.

The touched waypoint will be deleted from the list.

3Touch [OK] on the “Waypoints List” screen.

The route is recalculated, and “Route confirmation screen” appears.

4Touch [OK].

The map of the current position appears.

Sorting waypoints

You can sort waypoints and recalculate the route.

pYou cannot sort waypoints that you have already passed.

1 Display the “Waypoints List” screen.

3Touch the waypoint or destination.

Put them in the desired order.

# Touch [Automatic].

You can sort the destination and waypoints automatically. The system will show the nearest waypoint (distance in a straight line) from the current location as waypoint 1, and sort the other points (including your destination) in order of distance from the waypoint 1.

# Touch [Clear].

The sorting waypoints is canceled.

4Touch [OK].

The “Waypoints List” screen appears.

5Touch [OK] on the “Waypoints List” screen.

The route is recalculated, and “Route confirmation screen” appears.

6Touch [OK].

The map of the current position appears.

Modifying the route calculation conditions

The settings related to route calculation can be customized.

1Display the “Route confirmation screen”.

2Touch [Options].

The “Route Options” screen appears.

route current the modifying and Checking

En 53

Chapter

07 Checking and modifying the current route

# Touch [No].

Returns to the previous display without deleting the route.

=For details concerning operations, refer to

Modifying the route calculation conditions on page 49.

Canceling the route guidance

If you no longer need to travel to your destination, follow the steps below to cancel the route guidance.

1Display the “Destination Menu” screen.

2Touch [Cancel Route].

A message confirming the cancellation of the current route appears.

3 Touch [Yes].

The current route is deleted, and a map of your surroundings reappears.

# Touch [Skip].

The next waypoint along the route can be skipped.

A new route to your destination through all remaining waypoints, except for the skipped waypoint, is calculated.

When the route calculation is completed, “Route confirmation screen” appears.

p[Skip] is available only when a waypoint is set.

54 En

 

Chapter

Searching for and selecting a location

08

 

 

CAUTION

For safety reasons, these route-setting functions are not available while your vehicle is in motion. To enable these functions, you must stop in a safe place and put on the parking brake before setting your route.

pSome information regarding traffic regulations depends on the time when the route calculation is performed. Thus, the information may not correspond with a certain traffic regulation when your vehicle actually passes through the location in question. Also, the information on the traffic regulations provided will be for a passenger vehicle, and not for a truck or other delivery vehicles. Always follow the actual traffic

regulations when driving.

To search for a location, display the “Destination Menu” screen.

1Press the HOME button to display the “Top Menu”.

2Touch [Destination].

The “Destination Menu” screen appears.

Searching for a location by address

The most frequently used function is [Address], in which the address is specified and the destination is searched.

You can select the method of searching for a location by address.

! Searching for a city name first

!Finding the location by specifying the house number

To search for a location, display the “Address Search” screen.

1Display the “Destination Menu” screen.

2Touch [Address].

The “Address Search” screen appears.

3Touch the key next to “Country” to select the country.

If the destination is in another country, this changes the country setting.

p Once the country has been selected, you only have to change countries when your destination is outside of the country you selected.

4Touch the key next to “State” and touch the desired state, province, or territory on the list.

If the location that you want to search for is in another state, province, or territory, this changes the area setting.

p Once the state, province, or territory has been selected, you only have to change states, provinces, or territories when your destination is outside of the state, province, or territory you selected.

Searching for a city name first

pDepending on the search results, some steps may be skipped.

1Display the “Address Search” screen.

2Touch [City].

The “Enter City Name” screen appears.

location a selecting and for Searching

En 55

Chapter

08 Searching for and selecting a location

3Enter the city name and then touch [OK].

The “Select City” screen appears.

4Touch the desired city name.

The “Street Name” screen appears.

# Touch .

The representative location of the city appears on the map screen.

5Enter the street name and then touch [OK].

The “Street Selection” screen appears.

6Touch the desired street.

The “Enter House Number” screen appears.

7 Enter the house number and then touch [OK].

The “House Number Selection” screen appears.

8 Touch the desired house number range.

The searched location appears on the map screen.

Finding the location by specifying the house number

pDepending on the search results, some steps may be skipped.

1Display the “Address Search” screen.

2Touch [House #].

The “Enter House Number” screen appears.

3 Enter the house number and then touch [OK].

The “Enter Street Name” screen appears.

4Enter the street name and then touch [OK].

The “Street Selection” screen appears.

5Touch the desired street.

The “Enter City Name” screen appears.

56 En

Searching for and selecting a location

6Enter the city name and then touch [OK].

The “Select City” screen appears.

7Touch the desired city name.

The “House Number Selection” screen appears.

# Touch .

The representative location of the city appears on the map screen.

8 Touch the desired house number range.

The searched location appears on the map screen.

Searching for a name by entering multiple keywords

You can search for a name (such as a city name or a street name) by entering multiple keywords.

p Up to three keywords can be entered. p Enter a space between keywords as you

want to enter several ones.

The result of search depends on the number of the entered keywords.

Entering a keyword

All names containing the word beginning with entered keyword are displayed as a search result.

Entering two keywords

The names including the following two words below are displayed as a result:

!The word that matches with the first keyword you entered.

!The word beginning with the second keyword.

Entering three keywords

The names including the following two words below are displayed as a result:

!The words that match with both first and second keywords you entered.

!The word beginning with the third keyword. e.g. Searching “East West Street”.

Entered key-

Search results

words

 

 

 

EAST W

“East West Street” is searchable.

 

 

WEST S

“East West Street” is searchable.

 

 

EAST WEST S

“East West Street” is searchable.

 

 

WEST STREET

“East West Street” is searchable.

E

 

 

 

W E S

“East West Street” is not search-

able.

 

 

 

E WEST

“East West Street” is not search-

STREET

able.

 

 

Setting up a route to your home

If your home location is stored, the route home can be calculated by touching a single key.

1Display the “Destination Menu” screen.

2Touch [Return Home].

“Location confirmation screen” appears.

If the home location has not been stored yet, the confirmation message appears.

# Touch [Register].

The “Set Home” screen appears.

=For details, refer to Registering your home on page 96.

Chapter

08

location a selecting and for Searching

En 57

Chapter

08 Searching for and selecting a location

Searching for Points of Interest (POI)

Information about various facilities (Points Of Interest - POI), such as gas stations, parking lots or restaurants, is available. You can search for a POI by selecting the category (or entering the POI Name).

To search for POIs, display the “POI Search” screen.

1Display the “Destination Menu” screen.

2Touch [POI].

The “POI Search” screen appears.

Searching for POIs by specifying a category first

You can search for POIs with one touch by touching the preset category.

1Display the “POI Search” screen.

2Touch the desired category.

The “POI List” screen appears.

3 Touch the POI you want.

The searched location appears on the map screen.

State code key

3Touch the state code key and touch the desired state, province, or territory on the list.

If the location that you want to search for is in another state, province, or territory, this changes the area setting.

# Touch [Country] to display the country list. If the destination is in another country, this changes the country setting.

4Enter the POI name and then touch [OK].

The “POI List” screen appears.

5Touch the POI you want.

The searched location appears on the map screen.

# Touch [Sort].

Each time you touch [Sort] changes the sort order.

p Current order is displayed on the upper right of the screen.

! :

Sorts the items in the list in order by distance from the vehicle position.

! :

Sorts the items in the list alphabetically.

Searching for a POI directly from the name of the facilities

1Display the “POI Search” screen.

2Touch [Spell Name].

The “POI Name” screen appears.

Searching for a nearby POI

You can search for POIs in your surroundings.

1Display the “POI Search” screen.

2Touch [Near Me].

POI’s are divided into several categories.

58 En

 

Chapter

Searching for and selecting a location

08

 

 

3 Touch the category you want.

The “POI List” screen appears.

pIf there are more detailed categories within the selected category, repeat this step as many times as necessary.

4 Touch the POI you want.

The searched location appears on the map screen.

Searching for POIs around the destination

pThis function is available when the route is set.

1Display the “POI Search” screen.

2Touch [Near Destination].

POI’s are divided into several categories.

3 Touch the category you want.

The “POI List” screen appears.

pIf there are more detailed categories within the selected category, repeat this step as many times as necessary.

4 Touch the POI you want.

The searched location appears on the map screen.

Searching for POIs around the city

You can search for POIs around a specified city.

1Display the “POI Search” screen.

2Touch [Around City].

The “Enter City Name” screen appears.

State code key

3

Touch the state code key and touch the

 

desired state, province, or territory on the

 

list.

 

If the location that you want to search for is in

 

another state, province, or territory, this

forSearching

4

Enter the city name and then touch

changes the area setting.

 

# Touch [Country] to display the country list.

 

If the destination is in another country, this

 

changes the country setting.

 

[OK].

and

The “Select City” screen appears.

The representative location of the city appears on

selecting

5

Touch the desired city name.

 

The “POI List” screen appears.

 

#

Touch .

 

the map screen.

a

location

6

Touch the category you want.

 

POI’s are divided into several categories.

 

7

Touch the POI you want.

 

The searched location appears on the map screen.

Selecting destination from

“Favorites”

Storing locations you visit frequently saves time and effort.

Selecting an item from the list provides an easy way to specify the position.

pThis function is not available when there is no registered location in “Favorites”.

En 59

Chapter

08 Searching for and selecting a location

=For details, refer to Registering a location into “Favorites” on page 62.

1The “Destination Menu” screen appears.

2Touch [Favorites].

The “Favorites” screen appears.

3 Touch the entry you want.

The searched location appears on the map screen.

Searching for POIs by using the data on the SD memory card

Creating a customized POI is possible by using the utility program “AVIC FEEDS” which is available separately, on your PC. (“AVIC FEEDS” will be available on our website.) Storing the customized POI properly and inserting the SD memory card enables the system to use the data for searches.

1Insert an SD memory card into the SD card slot.

=For more details of the operation, refer to Inserting and ejecting an SD memory card on page 29.

2Display the “Destination Menu” screen.

3Touch [AVIC FEEDS].

POI’s are divided into several categories.

4 Touch the category you want.

The “Select POI” screen appears.

5 Touch the POI you want.

The searched location appears on the map screen.

Selecting a location you searched for recently

The places that you have searched for in the past are automatically stored in “History”.

pIf no location is stored in Destination History, you cannot select [History]. (If you perform a route calculation, you can select [History].)

p“History” can store up to 100 locations. If the entries reach the maximum, the new entry overwrites the oldest one.

1Display the “Destination Menu” screen.

2Touch [History].

The “Destination History List” screen appears.

3 Touch the entry you want.

The searched location appears on the map screen.

Searching for a location by coordinates

Entering a latitude and longitude pinpoints the location.

1Display the “Destination Menu” screen.

2Touch [Coordinates].

The “Coordinate Input” screen appears.

60 En

 

Chapter

Searching for and selecting a location

08

 

 

3Touch [East] or [West], and then enter the longitude.

To enter W 50°1’2.5” for example, touch [West], [0], [5], [0], [0], [1], [0], [2], and [5].

4Touch [North] or [South], and then enter the latitude.

To enter N 5°1’2.5” for example, touch [North], [0], [5], [0], [1], [0], [2], and [5].

5Touch [OK].

The searched location appears on the map screen.

location a selecting and for Searching

En 61

Chapter

09 Registering and editing locations

Registering a location into

“Favorites”

Registering a location by

“Favorites”

Favorites can store up to 400 registered locations. These can include your home location, favorite places, and destinations you have already registered.

1Display the “Destination Menu” screen.

2Touch [Favorites].

The “Favorites” screen appears.

3 Touch [Add].

The “Select Search method” screen appears.

4Search for a location.

=For details, refer to Chapter 8.

5When the map of the location you want to register is displayed, touch [OK].

The location is registered, and then the “Edit Favorite” screen appears.

=For details, refer to Editing the entry in “Favorites” on this page.

6Touch [OK].

The registration is completed.

Registering a location by scroll mode

1 Touch and drag the screen to scroll the map to the position that you want to register.

2Touch to display the Quick Access menu.

3Touch .

The location is registered, and then the “Edit Favorite” screen appears.

=For details, refer to Editing the entry in “Favorites” on this page.

4 Touch [OK].

The registration is completed.

Editing registered locations

Editing the entry in “Favorites”

1Display the “Destination Menu” screen.

2Touch [Favorites].

The “Favorites” screen appears.

3 Touch next to the location that you want to edit.

The “Edit Favorite” screen appears.

4 Touch [Name].

You can enter the desired name.

pUp to 17 characters can be input for the name.

#Touch [Phone #].

You can edit the registered phone number. To dial the number, touch [Call].

# Touch [Icon].

The symbol displayed on the map and “Favorites”.

# Touch [Modify Location].

You can change the registered location by scrolling the map.

62 En

 

Chapter

Registering and editing locations

09

 

 

Editing your home

When you have already registered your home, you can edit the information of your home.

1Display the “Destination Menu” screen.

2Touch [Favorites].

The “Favorites” screen appears.

pHome location is displayed on the top of the list.

3 Touch next to the home location.

The “Edit Favorite” screen appears.

# Touch [Phone #].

You can edit the registered phone number. To dial the number, touch [Call].

# Touch [Modify Location].

You can change the registered location by scrolling the map.

4 Touch [OK].

The registration is completed.

Sorting the entry in “Favorites”

1Display the “Destination Menu” screen.

2Touch [Favorites].

The “Favorites” screen appears.

3 Touch [Sort].

Each time you touch [Sort] changes the sort order.

p Current order is displayed on the upper right of the screen.

! :

Sorts the items in the list in order by distance from the vehicle position.

! :

Sorts the items in the list alphabetically.

! :

Sorts the items in the list in order of the recently used items.

Deleting the entry in “Favorites”

1Display the “Destination Menu” screen.

2Touch [Favorites].

The “Favorites” screen appears.

3 Touch [Delete].

The “Delete from Favorites” screen appears.

4 Select the location you want to delete.

A check mark appears by the selected location.

#Touch [All]. Selects all entries.

#Touch [None].

locations editing and Registering

En 63

Chapter

09 Registering and editing locations

Displayed when all locations are selected. Cancels all selected locations.

5 Touch [Delete].

A message will appear asking you to confirm the deletion.

6 Touch [Yes].

The data you selected is deleted.

# Touch [No]. Cancels the deletion.

Exporting and importing the entry in “Favorites”

Exporting the entry in “Favorites”

Exporting the “Favorites” data to an SD memory card for editing is possible by using the utility program “AVIC FEEDS” which is available separately, on your PC.

pIf there is a previous data in the SD memory card, the data is overwritten with new data when current data is exported.

1Insert an SD memory card into the SD card slot.

=For more details of the operation, refer to Inserting and ejecting an SD memory card on page 29.

2Display the “Destination Menu” screen.

3Touch [Favorites].

The “Favorites” screen appears.

4 Touch .

Exporting the data starts.

After exporting the data is finished, the following message appears.

5 Touch [OK].

The “Favorites” screen appears.

Importing “Favorites” edited on “AVIC FEEDS”

You can import the locations that you have edited on the utility program “AVIC FEEDS” which is available separately to “Favorites”.

pWhen a location that is already registered in “Favorites” is imported, the location is overwritten.

1Insert an SD memory card into the SD card slot.

=For more details of the operation, refer to Inserting and ejecting an SD memory card on page 29.

2Display the “Destination Menu” screen.

3Touch [Favorites].

The “Favorites” screen appears.

4 Touch .

The following message appears.

64 En

 

Chapter

Registering and editing locations

09

 

 

5 Touch [Yes].

Data import starts.

After importing the data is finished, the “Favorites” screen appears.

Deleting an entry in “History”

Items in History can be deleted. All entries in History can be deleted at once.

1Display the “Destination Menu” screen.

2Touch [History].

The “Destination History List” screen appears.

3 Touch [Delete].

The “Delete from History” screen appears.

4 Select the location you want to delete.

A check mark appears by the selected location.

#Touch [All]. Selects all entries.

#Touch [None].

Displayed when all locations are selected. Cancels all selected locations.

5 Touch [Delete].

A message will appear asking you to confirm the deletion.

6 Touch [Yes].

The data you selected is deleted.

# Touch [No]. Cancels the deletion.

locations editing and Registering

En 65

Chapter

10 Browsing information on MSN Direct

If you have an active subscription to MSN Direct service, you can check and

browse various information on your navigation system, such as gas prices, movie times, weather conditions and traffic information. The information will be updated periodically.

IMPORTANT:

To receive MSNâ Direct on an MSN Directready device, you must be within an MSN Direct coverage area; see http://www.msndirect. com/pioneer for current coverage maps. Coverage areas are affected by reception limitations of the FM network as well as other factors, which may affect the ability to receive FM broadcasts. Coverage areas are subject to change. Not all content is available in all coverage areas.

© 2008 Microsoft Corporation. All rights reserved. Microsoft, MSN, and the MSN logo are trademarks of the Microsoft group of companies.

Notice about MSN Direct

Pioneer is not responsible for the accuracy of the MSN Direct content. The MSN Direct content may not be current or available at times, and is subject to change without notice.

General flow chart:

1Check your product key.

You have to know your product key for the subscription.

(Refer to Checking your product key on this page.)

j

2Make an online subscription to MSN Direct service using your PC.

(Refer to Subscribing to the MSN Direct service on the next page.)

j

3Activate the MSN Direct service on this product.

(Refer to Activating the MSN Direct function on the next page.)

j

4Activation is complete.

Checking your product key

The product key that you can find here is used in the online subscription.

1Touch [Destination] on the “Top Menu”, and then touch [MSN Direct].

The “MSN Direct” screen appears.

2Touch [Status].

3Write your product key down in the following box;

Activating the service

You have to activate MSN Direct first.

pA web-connected computer is required for the online subscription.

pIf you have difficulty for the online subscription, please call toll-free 1-866-658-7032.

66 En

 

Chapter

Browsing information on MSN Direct

10

 

 

Subscribing to the MSN Direct service

Within two days of completing the subscription, execute Activating the MSN Direct function.

1Access the following URL and read the description. http://www.msndirect.com/pioneer

2Be sure to check the coverage area and other availabilities of MSN Direct on the web page.

3Go to the page for activation and enter your product key.

4Follow the directions on the web page to complete the subscription.

Activating the MSN Direct function

After the online subscription, complete the activation so that the navigation system can receive the information.

This operation must be performed under the following conditions

You are currently in the coverage area of MSN Direct.

1Boot-up your navigation system.

2Touch [Destination] on the “Top Menu”, and then touch [MSN Direct].

The “MSN Direct” screen appears.

3Touch [Status].

4Wait until the activation status changes to “Active”.

It may take approximately 20 or 30 minutes to complete the activation.

After activation is complete, the information will be available on each menu.

Browsing gas prices

Recent gas prices of nearby gas stations are displayed in a list.

Although the MSN Direct service regularly updates gas price information, the information provided may not necessarily correspond to actual gas prices. Please refer to Notice about MSN Direct on the previous page.

It may take up to 24 hours for all the data to become available under the following conditions:

!When you use MSN Direct for the first time.

!When you have not performed this function previously around the current area.

!After the navigation system has been turned off for a few days.

1 Touch [Destination] on the “Top Menu”, and then touch [MSN Direct].

The “MSN Direct” screen appears.

2 Touch [Gas Prices].

The “Gas Prices” screen appears.

3 Touch the desired tab to change the sort order.

Available options;

![Dist.] (default):

Sorts the items in the list in order by distance from the vehicle position.

![Name]:

Sorts the items in the list alphabetically.

![Price]:

Direct MSN on information Browsing

En 67

Chapter

10 Browsing information on MSN Direct

Sorts the items in the list by price.

# Touch [Refresh].

The information is updated.

p[Refresh] appears when new gas prices information is received.

4 Touch on the item that you want to view in detail.

# Touch .

“Location confirmation screen” appears.

=For details, refer to Checking the location on the map on page 48.

5 Touch [OK].

“Location confirmation screen” appears.

=For details, refer to Checking the location on the map on page 48.

Searching for a theater by selecting a movie title

1Touch [Destination] on the “Top Menu”, and then touch [MSN Direct].

2Touch [Movie Times].

The “All Movie Theaters” screen appears.

3 Touch [All Movie Titles].

The movie titles now showing are displayed.

# Touch [Refresh].

The information is updated.

p[Refresh] appears when the new information is received.

4 Touch the desired movie title.

The theaters that are currently showing the selected movie are displayed.

Browsing movie times

Nearby theaters can be displayed on a list. Switching the screen allows you to see the movie title now showing.

Although the MSN Direct service regularly updates movie information, the information provided may not necessarily correspond to actual movie information. Please refer to Notice about MSN Direct on page 66.

It may take up to 6 hours for all the data to become available under the following conditions:

!When you use MSN Direct for the first time.

!When you have not performed this function previously around the current area.

!After the navigation system has been turned off for a few days.

# Touch [Refresh].

The information is updated.

p[Refresh] appears when the new information is received.

5 Touch the desired tab to change the sort order.

Available options;

![Dist.] (default):

Sorts the items in the list in order by distance from the vehicle position.

68 En

 

Chapter

Browsing information on MSN Direct

10

 

 

![Name]:

Sorts the items in the list alphabetically.

6 Touch on the item that you want to view in detail.

# Touch .

“Location confirmation screen” appears.

=For details, refer to Checking the location on the map on page 48.

7 Touch [OK].

“Location confirmation screen” appears.

=For details, refer to Checking the location on the map on page 48.

#Touch [Call].

Enables you to call the position if a telephone number is available. (Pairing with cellular phone featuring Bluetooth wireless technology is required.)

Searching for a movie title by selecting a theater

1Touch [Destination] on the “Top Menu”, and then touch [MSN Direct].

2Touch [Movie Times].

The “All Movie Theaters” screen appears.

3Touch the desired tab to change the sort order.

Available options;

![Dist.] (default):

Sorts the items in the list in order by distance from the vehicle position.

![Name]:

Sorts the items in the list alphabetically.

4Touch the desired theater.

The movie titles currently shown on the selected theater are displayed.

# Touch .

“Location confirmation screen” appears.

=For details, refer to Checking the location on the map on page 48.

#Touch [Refresh].

The information is updated.

p[Refresh] appears when the new information is received.

5Touch on the item that you want to view in detail.

6Touch [OK].

“Location confirmation screen” appears.

=For details, refer to Checking the location on the map on page 48.

#Touch [Call].

Enables you to call the position if a telephone number is available. (Pairing with cellular phone featuring Bluetooth wireless technology is required.)

Browsing weather information

Local weather information can be displayed on a list. Switching the screen allows you to see worldwide weather conditions.

Although the MSN Direct service regularly updates weather information, the information provided may not necessarily correspond to actual weather conditions. Please refer to Notice about MSN Direct on page 66.

Checking the local weather information

1Touch [Destination] on the “Top Menu”, and then touch [MSN Direct].

2Touch [Weather].

The local weather information is displayed.

Direct MSN on information Browsing

En 69

Chapter

10 Browsing information on MSN Direct

The city name, weather, temperature and wind direction are displayed in list format.

3 Touch the desired area.

Detailed information is displayed.

Touching [Forecast] displays the weather forecasts for these three days.

Checking worldwide weather conditions

1Touch [Destination] on the “Top Menu”, and then touch [MSN Direct].

2Touch [Weather].

The local weather information is displayed.

3 Touch [Worldwide].

Worldwide weather conditions are displayed. The area names and weather conditions are displayed on the list. The list is sorted alphabetically by the area name.

4 Touch the desired area.

Detailed information is displayed.

Using traffic information

You can view current traffic conditions and information. When the navigation system receives updated traffic information, it will overlay the traffic information on your map and also display detailed text information when available.

In the default setting, the navigation system takes into account traffic information and tries to avoid traffic congestions and suggest better routes. Also, when you are traveling along a route and the system finds another better route for avoiding the traffic congestion, the current route will be recalculated automatically.

The term “traffic congestion” in this section indicates the following types of traffic conditions:

Stop-and-go traffic

Stopped traffic

Closed/blocked roads

Viewing the traffic event

Traffic Information is displayed on a screen in the form of a list. This allows you to check how many traffic incidents have occurred, their location and their distance from your current position.

Although the MSN Direct service regularly updates traffic information, the information provided may not necessarily correspond to actual traffic conditions. Please refer to Notice about MSN Direct on page 66.

1Touch [Destination] on the “Top Menu”, and then touch [MSN Direct].

2Touch [Traffic Events].

The “Traffic Event List” screen appears.

70 En

 

Chapter

Browsing information on MSN Direct

10

 

 

3 Select an incident you want to view in detail.

The details of the selected incident are displayed.

been removed, the list is updated to reflect the new situation.

# Touch .

Touching allows you to check the location on a map. (Traffic information without positional information cannot be checked on a map.)

4 Touch .

Return to the previous screen.

Checking traffic information on the route

pTouching an incident you want to see allows you to view the detailed information of the incident. If the information cannot be dis-

played on one screen, touch or to view the remaining information.

#Touch [Sort].

You can sort the traffic information.

Each time you touch the key changes that setting.

! :

You can sort the traffic information by distance from your current position.

For the list displayed when you touch [Traffic Events], the list will be sorted according to the linear distance from the vehicle position to the traffic information.

For the list displayed when you touch [Traffic On Route], the list will be sorted according to the distance from the vehicle position to the traffic information.

! :

You can sort the traffic information in alphabetical order.

! :

You can sort the traffic information according to the incident.

The list will be sorted in the order of closed/ blocked roads, traffic congestion, acci-

dents, road works and others.

Current order is displayed on the upper right of the screen.

# Touch [Refresh].

When new traffic information is received, current information is changed or old information has

All traffic information on the current route is displayed on screen in a list.

% Touch [Traffic On Route].

 

The “Traffic On Route” screen appears.

 

The method for checking the content dis-

 

played on the screen is the same for “Viewing

Browsing

the traffic event”.

 

How to read traffic information

 

on the map

information

The traffic event information displayed on the

 

map is as follows.

 

p A line is displayed only when the map scale

 

is 2.5 miles (5 km) or lower.

 

p Icon appears only when the scale on the

on

map is 10 miles (20 km) or lower. If the

 

scale is changed, the icons are resized ac-

DirectMSN

cording to the selected scale.

 

Traffic event icon

! with yellow line: Stop-and-go traffic

! with red line: Stopped traffic

En 71

Chapter

10 Browsing information on MSN Direct

! with black line: Closed/blocked roads

! etc.:

Accidents, constructions, etc.

Setting an alternative route to avoid traffic congestion

The navigation system checks whether or not there is the traffic information on your route at regular time intervals. If the navigation system detects any traffic jams on your current route, the system tries to find a better route in the background.

pThe following types of traffic incidents on the route will be checked: slow, queuing and stationary traffic, and closed/blocked roads.

Checking for traffic congestion automatically

If there is information about traffic congestion on your current route and if an alternative route can be found, the navigation system will recommend a new alternative route automatically. In such a case, the following screen will appear.

1 Touch [New].

The recommended route is displayed on the screen.

# Touch [Current].

The current route is displayed on the screen.

2 Touch [OK].

The displayed route is set.

pWhen no selection is made, the screen returns to previous screen.

Checking traffic information manually

Touching the notification icon on the map screen allows you to check traffic information on your route while icon is displayed. The notification icon is only displayed on the navigation map screen if there is any traffic information on your route.

pThe notification icon will not be available when your vehicle deviate from the route.

1Set [Show Traffic Incident] to [View].

=For details, refer to Show Traffic Incident on page 43.

2Display the map screen.

The icon appears when the system acquires traffic information on the current route.

3 Touch the icon while the icon is displayed.

Traffic information on the current route is displayed on the map screen.

12

1Distance from the current position of your vehicle to the point of entry into the new route.

2Difference in distance and travel time between the existing route and new route.

pThere is no action if the system cannot find any traffic congestion information on your route or the system cannot find an alternative.

4 Touch [Diversion] to search for an alternative route.

After touching [Diversion], the route is recalculated taking all traffic congestion on your current route into account.

72 En

 

Chapter

Browsing information on MSN Direct

10

 

 

p [Diversion] will be enable only when the system can find “traffic congestion”.

p“Notification icon” shows the nearest traffic information on the route. However, if you touch [Diversion], the route is recalculated by taking into account not only this information, but also all traffic congestion infor-

mation on the route.

For the subsequent operations, see “Checking for traffic congestion automatically”.

=For details, refer to Checking for traffic congestion automatically on the previous page.

#Touch [List].

The “Traffic On Route” screen appears.

# Touch .

The message disappears, and the map display reappears.

Viewing the traffic flow

Traffic Information is displayed on a screen in the form of a list. This allows you to check how many traffic incidents have occurred, their location and their distance from your current position.

Although the MSN Direct service regularly updates traffic information, the information provided may not necessarily correspond to actual traffic conditions. Please refer to Notice about MSN Direct on page 66.

1Touch [Destination] on the “Top Menu”, and then touch [MSN Direct].

2Touch [Traffic Flow].

A list with traffic event information that has been received is shown.

Places (street names) where incidents have occurred are displayed on the list.

3 Select an incident you want to view in detail.

The details of the selected incident are displayed.

pTouching an incident you want to see allows you to view the detailed information of the

incident. If the information cannot be displayed on one screen, touch or to view the remaining information.

# Touch [Sort].

You can sort the traffic information.

Each time you touch the key changes that setting.

 

!

:

 

 

 

You can sort the traffic information by dis-

 

 

 

tance from your current position.

 

 

 

For the list displayed when you touch [Traf-

 

 

 

fic Events], the list will be sorted according

 

 

 

to the linear distance from the vehicle posi-

 

 

 

tion to the traffic information.

 

 

 

For the list displayed when you touch [Traf-

 

 

 

fic On Route], the list will be sorted accord-

 

 

 

ing to the distance from the vehicle position

 

 

 

to the traffic information.

 

 

!

:

Browsing

 

 

You can sort the traffic information in alpha-

 

 

 

 

 

betical order.

 

 

!

:

 

 

 

You can sort the traffic information accord-

 

 

 

ing to the incident.

information

 

 

The list will be sorted in the order of closed/

 

 

 

 

 

blocked roads, traffic congestion, acci-

 

 

 

dents, road works and others.

 

Current order is displayed on the upper right of

 

the screen.

 

#

Touch [Refresh].

on

When new traffic information is received, current

information is changed or old information has

MSN

 

been removed, the list is updated to reflect the

 

new situation.

Direct

#

Touch .

 

The traffic event information displayed on the map is as follows.

Traffic flow icon and line

En 73

Chapter

10 Browsing information on MSN Direct

!Red: average speed in this area is slower than 15 mph (24 km/h)

!Yellow: average speed in this area is between 15 mph to 45 mph (24 km/h to 72 km/ h)

!Green: average speed in this area is faster than 45 mph (72 km/h) (An icon without a line will be displayed)

Selecting traffic information to display

There are different types of traffic information that can be received via the MSN Direct service, and you can select which types will be incorporated and displayed on your navigation system.

1Touch [Destination] on the “Top Menu”, and then touch [MSN Direct].

2Touch [Traffic Settings].

The “Traffic Settings” screen appears.

pTouching [All (None)] selects or deselects all traffic information.

#Touch [All].

Selects all traffic information.

# Touch [None].

Displayed when all traffic information are selected. Cancels all selected traffic information.

5 Touch [OK].

The selected traffic information icon is added to the screen.

6 Touch [OK].

3 Touch [Displayed Traffic Information]. The “Traffic Type Settings” screen appears.

4 Touch the traffic information item to display.

A check mark appears by the selected traffic information.

Browsing local events

The nearby events to be held in the next few days are displayed on a list, and you can see the detail event information.

Although the MSN Direct service regularly updates local event information, the information provided may not necessarily correspond to actual local event conditions. Please refer to Notice about MSN Direct on page 66.

1Touch [Destination] on the “Top Menu”, and then touch [MSN Direct].

2Touch [Local Events].

The “Local Event Date” screen appears.

74 En

Browsing information on MSN Direct

3Touch the date on which you want to check the events.

The “Local Event Groups List” screen appears.

4Touch the category of events that you want to check.

The “Local Event Sub Groups List” screen appears.

5Touch the subcategory of events that you want to check.

The “Local Events” screen appears.

6Touch the desired tab to change the sort order.

Available options;

![Dist.] (default):

Sorts the items in the list in order by distance from the vehicle position.

![Name]:

Sorts the items in the list alphabetically.

7Touch the desired event to display detailed information of the event.

# Touch .

“Location confirmation screen” appears.

=For details, refer to Checking the location on the map on page 48.

#Touch [Refresh].

The information is updated.

p[Refresh] appears when the new information is received.

8 Touch [OK].

“Location confirmation screen” appears.

=For details, refer to Checking the location on the map on page 48.

#Touch [Call].

Enables you to call the position if a telephone number is available. (Pairing with cellular phone featuring Bluetooth wireless technology is required.)

Browsing news headlines

Recent news headlines are displayed in a list.

Although the MSN Direct service regularly updates news headlines, the information provided may not necessarily correspond to current news headlines. Please refer to Notice about MSN Direct on page 66.

1Touch [Destination] on the “Top Menu”, and then touch [MSN Direct].

2Touch [News].

3 Touch the desired news headline.

Further details about the news are displayed.

Chapter

10

Direct MSN on information Browsing

En 75

Chapter

10 Browsing information on MSN Direct

# Touch [Refresh].

The information is updated.

p[Refresh] appears when the new information is received.

4 Touch or to scroll the list.

Browsing stock quotes

Recent stock quotes are displayed in a list.

Although the stock quote displayed onscreen is updated about 40 minutes (approx.), these prices are not realtime values.

It may take up to 20 minutes for all the data to become available under the following conditions:

!When you use MSN Direct for the first time.

!When you have not performed this function previously around the current area.

!After the navigation system has been

turned off for a few days.

=Please refer to Notice about MSN Direct on page 66.

3 Touch [Add].

The “Stock Info” screen appears.

4 Enter the stock symbol that you want to select, and then touch [OK].

The selected stock symbol is added to the

“Stock Info” screen.

pArrow in the left of each item indicates the stock price movement. If there is no stock price movements than previous close, “—” is displayed.

Viewing the detailed stock quotes

1Touch [Destination] on the “Top Menu”, and then touch [MSN Direct].

2Touch [Stocks].

3Touch the desired stock quote.

Detailed stock quote information is displayed.

# Touch [Delete].

The message confirming whether to delete the entry appears.

And then touch [OK] to delete the stock symbol from the “Stock Info” screen.

Selecting stock symbols

Up to 30 stock symbols can be selected.

1Touch [Destination] on the “Top Menu”, and then touch [MSN Direct].

2Touch [Stocks].

The “Stock Info” screen appears.

pThe seven stock indices is always selected and displayed on the bottom of the list.

76 En

 

Chapter

Registering and connecting the Bluetooth device

11

 

 

If your devices feature Bluetoothâ technology, this navigation system can be connected to your devices wirelessly. This section describes how to set up a Bluetooth connection.

For more information about the connectivity with the devices featuring Bluetooth wireless technology, refer to the information on our website.

Preparing communication devices

This navigation system has a built-in function to use devices featuring Bluetooth wireless technology.

=For details, refer to Notes for hands-free phoning on page 90.

You can register and use devices that feature the following profiles with this navigation system.

!HFP (Hands Free Profile)

!A2DP (Advanced Audio Distribution Profile)

pWhen the navigation system is turned off, the Bluetooth connection is also disconnected. When the system restarts, the system automatically attempts to reconnect the previously-connected cellular phone. Even when the connection is severed for some reason, the system automatically reconnects the specified cellular phone (ex-

cept when the connection is severed due to cellular phone operation).

Registering your Bluetooth devices

You need to register your devices featuring Bluetooth wireless technology when you connect it for the first time. A total of 5 devices can be registered. Three registration methods are available:

! Searching for nearby Bluetooth devices

!Searching for a specified Bluetooth device

!Pairing from your Bluetooth devices

pIf you try to register more than 5 devices, the system will ask you to select one of the registered devices to delete.

= For details, refer to Deleting a registered

device on page 80.

To register your Bluetooth devices, display the

“Bluetooth Settings” screen.

1Press the HOME button to display the “Top Menu”.

2Touch [Settings].

The “Settings Menu” screen appears.

3 Touch [Bluetooth Settings].

The “Bluetooth Settings” screen appears.

Searching for nearby Bluetooth devices

The system searches for available Bluetooth devices near the navigation system, displays them in a list, and registers them for connection.

1Activate the Bluetooth wireless technology on your devices.

For some Bluetooth devices, no specific action is necessary to activate Bluetooth wireless technology. For details, refer to the instruction manual of your devices.

2Display the “Bluetooth Settings” screen.

3Touch [Registration].

The “Nearby Device List” screen appears.

device Bluetooth the connecting and Registering

En 77

Chapter

11 Registering and connecting the Bluetooth device

The system searches for devices featuring Bluetooth technology that are waiting for the connection and displays them in the list if the device has found.

pUp to 30 devices will be listed in the order that the devices are found.

4 Wait until your Bluetooth device appears in the list.

pIf you cannot find the Bluetooth device that you want to connect, check that the device is waiting for the Bluetooth wireless technology connection.

5 Touch the Bluetooth device name you want to register.

The message “Please follow the instructions on your mobile phone.” appears.

6 Enter the PIN code (the default PIN code is “1111”) using the Bluetooth device.

The device is registered in the navigation system.

After the device is successfully registered, the Bluetooth connection is established from the navigation system.

p If the registered device features HFP, the hands-free connection is made.

pIf the registered device features A2DP, Bluetooth Audio connection is made.

pIf the registered device features both HFP and A2DP, the hands-free connection is made and then the Bluetooth Audio connection is made.

Searching for a specified Bluetooth device

If you cannot connect your Bluetooth device using [Search devices] and [Register from mobile phone], try this method if your Bluetooth device is found in the list.

1Activate the Bluetooth wireless technology on your devices.

For some Bluetooth devices, no specific action is necessary to activate Bluetooth wireless technology. For details, refer to the instruction manual of your devices.

2Display the “Bluetooth Settings” screen.

3Touch [Registration].

The “Nearby Device List” screen appears.

4 Touch [Select specific devices].

The “Select specific devices” screen appears.

5 Touch the model name of the Bluetooth device to be connected.

The system searches for devices featuring Bluetooth technology that are waiting for the connection and displays them in the list if the device has found.

78 En

 

Chapter

Registering and connecting the Bluetooth device

11

 

 

pIf you cannot find the desired model name on the list, touch [Other phones] to search the devices available nearby.

6 Touch the Bluetooth device name you want to register.

The message “Please follow the instructions on your mobile phone.” appears.

7 Enter the PIN code (the default PIN code is “1111”) using the Bluetooth device.

The device is registered in the navigation system.

After the device is successfully registered, the Bluetooth connection is established from the navigation system.

p If the registered device features HFP, the hands-free connection is made.

p If the registered device features A2DP, Bluetooth Audio connection is made.

pIf the registered device features both HFP and A2DP, the hands-free connection is made and then the Bluetooth Audio connection is made.

Pairing from your Bluetooth devices

You can register the Bluetooth device by setting the navigation system to standby mode

and requesting connection from the Bluetooth device.

1Activate the Bluetooth wireless technology on your devices.

For some Bluetooth devices, no specific action is necessary to activate Bluetooth wireless technology. For details, refer to the instruction manual of your devices.

2Display the “Bluetooth Settings” screen.

3Touch [Registration].

The “Nearby Device List” screen appears.

4 Touch [Register from mobile phone].

The navigation system waits for a Bluetooth wireless technology connection.

5 Register the navigation system on your Bluetooth device.

If your device asks you to enter a password, enter the PIN code (password) of the navigation system.

When the device is successfully registered, the connection settings are made from the device.

pIf registration fails repeat the procedure from the beginning.

device Bluetooth the connecting and Registering

En 79

Chapter

11 Registering and connecting the Bluetooth device

Deleting a registered device

When you have already registered 5 Bluetooth devices and you want to add another one, you must first delete one of the registered devices.

pIf a registered phone is deleted, all the phone book entries and call history lists that correspond to the phone will be also cleared.

1Display the “Bluetooth Settings” screen.

2Touch [Registration].

The following message appears.

3 Touch [OK].

The “Delete from Connection List” screen appears.

4 Touch the Bluetooth device name that you want to delete.

The registration is canceled.

Connecting a registered Bluetooth device

The navigation system automatically connects the Bluetooth device selected as the target of

connection. However, connect the Bluetooth device manually in the following cases:

!Two or more Bluetooth devices are registered, and you want to manually select the device to be used.

!You want to reconnect a disconnected Bluetooth device.

!Connection cannot be established automatically for some reason.

If you start connection manually, carry out the following procedure. You can also connect the Bluetooth device by having the navigation system detect it automatically.

1Activate the Bluetooth wireless technology on your devices.

For some Bluetooth devices, no specific action is necessary to activate Bluetooth wireless technology. For details, refer to the instruction manual of your devices.

2Display the “Bluetooth Settings” screen.

3Touch [Connection].

The “Connection List” screen appears.

4 Touch the name of the device that you want to connect.

The “Select Profile” screen appears.

80 En

Registering and connecting the Bluetooth device

5 Touch the profile that you want to connect.

You can select the following profiles:

![Handsfree and Audio]:

Connects the device as the hands-free phone and the Bluetooth audio player.

![Audio]:

Connects the device as Bluetooth audio player.

![Handsfree]:

Connects the device as the hands-free

phone.

Connection starts.

When a connection is successfully established, a connection complete message appears, the screen returns to the map screen by touching [OK].

p To cancel the connection to your device, touch [Cancel].

pThe selected device is set for priority connecting.

pIf connection fails, check whether your de-

vice is waiting for a connection and then retry.

Chapter

11

device Bluetooth the connecting and Registering

En 81

Chapter

12 Using hands-free phoning

CAUTION

For your safety, avoid talking on the phone as much as possible while driving.

If your cellular phone features Bluetooth® technology, this navigation system can be connected to your cellular phone wirelessly. Using this hands-free function, you can operate the navigation system to make or receive phone calls. You can also transfer the phone book data stored in your cellular phone to the navigation system. This section describes how to set up a Bluetooth connection and how to operate a cellular phone featuring Bluetooth technology on the navigation system.

2: Network name of the cellular phone company

3: Strength of the Bluetooth connection between the navigation system and the de-

vice

4: Reception status of the cellular phone

5: Battery status of the cellular phone

Making a phone call

You can make a phone call in many different ways.

Direct dialing

1 Display the “Phone Menu” screen.

For more information about the connectivity with the cellular phone featuring Bluetooth wireless technology, refer to the information on our website.

2 Touch [Dial Pad].

The direct dial screen appears.

Displaying the Phone Menu

Use the “Phone Menu” if you connect the cellular phone to the navigation system for utilization.

=For more details of the operation, refer to Chapter 11.

1Press the HOME button to display the “Top Menu”.

2Touch [Phone].

The “Phone Menu” screen appears.

2 345

1

1 : Name of connected cellular phone

3Touch the number keys to enter the phone number.

The phone number that was input is displayed.

And then [OK] is activated.

# Touch .

The input number is deleted a digit at a time from the end of the number. Continuing to press this deletes all of the digits.

# Touch .

Return to the previous screen.

4Touch [OK] to make a call.

pTo cancel the call after the system starts dialing, touch .

5 Touch to end the call.

82 En

Using hands-free phoning

Making a call home easily

You can call home without taking the time to enter the phone number if the phone number has been registered.

1Display the “Phone Menu” screen.

2Touch [Call Home].

Dialing home starts.

pIf you have not registered your home number, a message appears. Touch [Register] to start registration.

=For details, refer to Registering your home on page 96.

Calling a number in the

“Contacts List”

After finding the entry you want to call in the “Contacts List” screen, you can select the number and make the call.

pBefore using this function, you need to set the phone number from the phone book to

“Contacts”.

=For details, refer to Transferring the phone book on page 87.

1Display the “Phone Menu” screen.

2Touch [Contacts].

The “Contacts List” screen appears.

3 Switch the page of the list to display the desired entry.

If you touch an alphabet tab, you can jump to the first page of the contacts whose names start with that letter.

Alphabet tabs

Makes the screen jump to the beginning of the page including the entry whose names start with any of selected alphabets.

Touching [#ABCDE] also displays the page including the entry whose names start with primary symbols or numbers.

Touching [Others] displays the page including entries that are not assigned to any of the other tabs.

4 Touch the desired entry on the list to make a call.

pIf the entry has multiple phone number data, the selection list appears.

#Touch [Search].

The “Contacts Name Search” screen appears. You can search by the names registered in the

“Contacts List” screen.

# Touch [Delete].

The “Delete from Contacts” screen appears. If you select the entry you want to delete and touch [Delete], a message appears.

If you touch [OK], the entry is deleted.

5 Touch to end the call.

Making a phone call using the received call history

The received call history saves 30 calls per registered cellular phone. If the number of calls exceeds 30, the oldest entry will be deleted.

1Display the “Phone Menu” screen.

2Touch [Received Calls].

The “Received Calls List” screen appears.

Chapter

12

phoning free-hands Using

En 83

Chapter

12 Using hands-free phoning

3 Touch an entry on the list.

Dialing starts.

pTo cancel the call after the system starts dialing, touch .

#Touch [Detail].

The “Detailed Information” screen appears.

You can check the details of the party before making a phone call.

4 Touch to end the call.

Making a phone call using the dialed number history

The dialed number history saves 30 calls per registered cellular phone. If the entries exceed 30, the oldest one will be deleted.

1Display the “Phone Menu” screen.

2Touch [Dialed Calls].

The “Dialed Calls List” screen appears.

3 Touch an entry on the list.

Dialing starts.

pTo cancel the call after the system starts dialing, touch .

#Touch [Detail].

The “Detailed Information” screen appears.

You can check the details of the party before making a phone call.

4 Touch to end the call.

Making a phone call using missed call history

The missed call history saves 30 calls per registered cellular phone. If the number of calls exceeds 30, the oldest entry will be deleted.

1Display the “Phone Menu” screen.

2Touch [Missed Calls].

The “Missed Calls List” screen appears.

3 Touch an entry on the list.

Dialing starts.

pTo cancel the call after the system starts dialing, touch .

#Touch [Detail].

The “Detailed Information” screen appears.

84 En

 

Chapter

Using hands-free phoning

12

 

 

You can check the details of the party before making a phone call.

4 Touch to end the call.

Dialing GOOG-411

CAUTION

4 Touch [Call] to make a call.

To cancel the call after the system starts dialing, touch .

5 Touch to end the call.

Dialing a facility’s phone number

You can make a call to facilities with phone number data.

pYou cannot make a call to locations or POIs that have no phone number data.

1Display the “Destination Menu” screen.

2Touch [POI].

The “POI Search” screen appears.

Local and/or long distance charges for making a phone call may apply.

You can dial GOOG-411 to dial the free business listing service of Googleä with one touch.

1 Touch [GOOG-411] on the “Phone Menu”.

= For details, refer to Displaying the Phone Menu on page 82.

Dialing GOOG-411 starts.

2 You can now use the GOOG-411 phone service.

For details about GOOG-411 service and availability, contact Googleä.

Dialing the entry in the “Favorites”

You can make a call to the entry registered in the “Favorites”.

1Display the “Destination Menu” screen.

2Touch [Favorites].

The “Favorites” screen appears.

3 Touch next to the location that you want to make a call.

The “Edit Favorite” screen appears.

3 Search for the POI.

The “POI List” screen appears.

=For details concerning operations, refer to

Searching for Points of Interest (POI) on page 58.

4Touch next to the POI that you want to call.

The “Detailed POI Information” screen appears.

5Touch [Call] to make a call.

To cancel the call after the system starts dialing, touch .

6 Touch to end the call.

Dialing from the map

You can make a call by selecting the icon of a registered location or a POI icon from the map screen.

pYou cannot make a call to locations or POIs that have no phone number data.

1Scroll the map, and place the cursor on an icon on the map.

2Touch .

The “Detailed POI Information” screen appears.

phoning free-hands Using

En 85

Chapter

12 Using hands-free phoning

3 Touch [Call] to make a call.

To cancel the call after the system starts dialing, touch .

4 Touch to end the call.

Receiving a phone call

You can perform hands-free answering by using the navigation system.

Answering an incoming call

The system informs you that it is receiving a call by displaying a message and producing a ring sound once.

If [Auto Answer Preference] is set to [Off], answer the call manually. Answering is available if any screen is displayed, such as the map screen or the setting screen.

pYou can set this navigation system to automatically answer incoming calls.

=For details, refer to Answering a call automatically on page 88.

1 When a call comes in, the answering operation menu appears on the screen.

# Touch [Vol –] or [Vol +].

You can adjust volume when you are talking.

#Touch to reject an incoming call.

#If you touch [Close Menu], the menu is closed and appears.

To display the menu again, touch .

3 Touch to end the call.

The call ends.

pIf the voice on the other end of the call is too quiet to hear, you can adjust the volume of the received voice.

=For more details about “Volume”, refer to Setting the Volume for Guidance and

Phone on page 98.

pYou may hear a noise when you hang up the phone.

pThe registered name appears if the phone number of the received call is already regis-

tered in “Contacts”.

pDepending on the caller ID service, the phone number of the received call may not be displayed. “Unknown” appears instead.

2 To answer an incoming call, touch .

The operation menu during a call appears.

Rejecting an incoming call

You can reject an incoming call.

=For details, refer to Setting the automatic rejection function on page 89.

% When a call comes in, touch .

The call is rejected.

pThe rejected call is recorded in the missed call history list.

=For details, refer to Making a phone call using missed call history on page 84.

86 En

 

Chapter

Using hands-free phoning

12

 

 

Transferring the phone book

You can transfer the numbers in a registered user phone’s address book into the Contacts. p Depending on the cellular phone, “Phone Book” may be called a name such as “Contacts”, “Business card” or something else.

pWith some cellular phones, it may not be possible to transfer the entire phone book at once. In this case, transfer addresses

one at a time from your phone book using your cellular phone.

pThe maximum 1 000 entries can be transferred per cellular phone. If the entries exceed 1 000, the extra entries will not be transferred. If more than one number is registered for one person, such as work place and home, each number is counted sepa-

rately.

p Each entry can hold up to 5 phone numbers.

pDepending on the cellular phone that is connected to this navigation system via Bluetooth technology, this navigation system may not be able to display the phone

book correctly. (Some characters may be garbled.)

p If the phone book in the cellular phone contains image data, the phone book may not be correctly transferred.

pThe transferred data can not be edited on the navigation system.

1 Connect the cellular phone that has the phone book to transfer.

=For details, refer to Connecting a registered Bluetooth device on page 80.

3 Check that the following screen is displayed, and operate your cellular phone to transfer the phone book entries.

After transferring the data is finished, a message asking whether you want to transfer more data appears.

4 Touch [No].

The transferred data is imported to the navigation system.

When the data is successfully imported, an import complete message is displayed and the “Contacts List” screen appears.

pIt may take time depending on how many entries will be transferred.

#Touch [Yes].

Repeat the steps to transfer more data.

phoning free-hands Using

2 Touch [Contacts Transfer] on the “Phone Menu” screen.

Setting the “Bluetooth

Settings”

To set the “Bluetooth Settings”, display the

“Bluetooth Settings” screen.

1Press the HOME button to display the “Top Menu”.

2Touch [Settings].

The “Settings Menu” screen appears.

En 87

Chapter

12 Using hands-free phoning

3 Touch [Bluetooth Settings].

The “Bluetooth Settings” screen appears.

Editing the device name

You can change the device name to be displayed on your cellular phone. (Default is [PIONEER NAVI].)

1Display the “Bluetooth Settings” screen.

2Touch [Device Name].

The keyboard to enter the name appears.

3 Touch to delete the current name, and enter the new name by using the keyboard.

4 Touch [OK].

The name is changed.

pUp to 16 characters can be entered for a device name.

Editing the password

You can change the password to be used for authentication on your cellular phone. (Default is [1111].)

pFour to eight characters can be entered for a password.

1Display the “Bluetooth Settings” screen.

2Touch [Password].

The “Set Password” screen appears.

3 Touch any key to enter the password you want to set and then touch [OK].

Stopping Bluetooth wave transmission

You can stop transmission of electric waves by turning off the Bluetooth function. If you do not use the Bluetooth wireless technology, we recommend selecting [Off].

1Display the “Bluetooth Settings” screen.

2Touch [Bluetooth On/Off].

Touching [Bluetooth On/Off] switching between [On] and [Off].

Echo canceling and noise reduction

When you are operating hands-free phoning in the vehicle, you may hear an undesirable echo. This function reduces the echo and noise while you are using hands-free phoning, and maintains a certain sound quality.

1Display the “Bluetooth Settings” screen.

2Touch [Echo Cancel].

Touching [Echo Cancel] switches between [On] and [Off].

Answering a call automatically

The navigation system automatically answers incoming calls to the cellular phone, so you can answer a call while driving without taking your hands off the steering wheel.

1Display the “Bluetooth Settings” screen.

2Touch [Auto Answer Preference]. The “Auto Answer Preference” screen appears.

88 En

 

Chapter

Using hands-free phoning

12

 

 

3Touch the desired option.

![Off]: No automatic response. Respond manually

![Immediately]: Answers immediately

![After 3 seconds]: Answers after three seconds

![After 6 seconds]: Answers after six seconds

![After 10 seconds]: Answers after ten seconds

Setting the automatic rejection function

If this function is on, the navigation system automatically rejects all incoming calls.

1Display the “Bluetooth Settings” screen.

2Touch [Refuse All Calls].

Touching [Refuse All Calls] switches between [On] and [Off].

pIf both “Refuse All Calls” and “Auto Answer Preference” are activated, “Refuse

All Calls” takes priority and all incoming calls are automatically rejected.

pIf “Refuse All Calls” is set to [On], rejected incoming calls will not be stored in the missed call list.

Clearing memory

You can clear the memory of each item that corresponds to the connected cellular phone: phone book, dialed/received/missed call history list and preset dials.

1Display the “Bluetooth Settings” screen.

2Touch [Clear Memory].

The “Clear Memory” screen appears.

On this screen, you can select the following items:

!Contacts:

You can clear the registered phone book.

!Received Calls List:

You can clear the received call history list.

!Dialed Calls List:

You can clear the dialed call history list.

!Missed Calls List:

You can clear the missed call history list.

#Touch [Clear All].

It clears all the data that correspond to the connected cellular phone.

3 Touch [Yes].

Data on the selected item is cleared from this navigation system’s memory.

pIf you do not want to clear memory that you have selected, touch [No].

Updating the Bluetooth wireless technology software

Update files will be available for download in the future. You will be able to download the latest update from an appropriate website to your PC.

pBefore you download the files and install the update, read through the instructions on the website. Follow the instructions on the website for steps until [Firmware update] becomes active.

phoning free-hands Using

En 89

Chapter

12 Using hands-free phoning

1Insert an SD memory card into the SD card slot.

=For more details of the operation, refer to Inserting and ejecting an SD memory card on page 29.

2Display the “Bluetooth Settings” screen.

3Touch [Firmware update].

The current version is displayed.

4 Touch [Firmware update].

Update starts.

Notes for hands-free phoning

General notes

!Connection to all cellular phones featuring Bluetooth wireless technology is not guaranteed.

!The line-of-sight distance between this navigation system and your cellular phone must be 10 meters or less when sending and receiving voice and data via Bluetooth technology. However, the actual transmission distance may be shorter than the estimated distance, depending on the usage environment.

!With some cellular phones, the speakers of the system may not produce a ring sound.

!If private mode is selected on the cellular phone, hands-free phoning may be disabled.

Registration and connection

!Cellular phone operations vary depending on the type of cellular phone. Refer to the

instruction manual that came with your cellular phone for detailed instructions.

!With cellular phones, phone book transfer may not work even though your phone is paired with the navigation system. In that case, disconnect your phone, perform pairing again from your phone to the navigation system, and then perform the phone book transfer.

Making and receiving calls

!You may hear a noise in the following situations:

When you answer the phone by using the button on the phone.

When the person on the other end of line hangs up the phone.

!If the person on the other end of the phone call cannot hear the conversation due to an echo, decrease the volume level for handsfree phoning. This may reduce the echo.

!With some cellular phones, even if you press the accept button on the cellular phone when a call comes in, hands-free phoning may not be performed.

!The registered name appears if the phone number of the received call is already registered in the phone book. When one phone number is registered under different names, the name that comes first alphabetically is displayed.

!If the phone number of the received call is not registered in the phone book, the phone number of the received call appears.

The received call history and the dialed number history

!Calls made or editing performed only on your cellular phone will not be reflected to the dialed number history or phone book in the navigation system.

!You cannot make a call to the entry of an unknown user (no phone number) in the received call history.

!If calls are made by operating your cellular phone, no history data will be recorded in the navigation system.

90 En

 

Chapter

Using hands-free phoning

12

 

 

Phone book transfers

!If there are more than 1 000 phone book entries on your cellular phone, all entries may not be able to be downloaded completely.

!With some cellular phones, it may not be possible to transfer all items in the phone book at one time. In this case, transfer items one by one from your cellular phone.

!Depending on the cellular phone, this navigation system may not display the phone book correctly. (Some characters may be garbled, or first name and last name may be in reverse order.)

!If the phone book in the cellular phone contains image data, the phone book may not be transferred correctly. (Image data cannot be transferred from the cellular phone.)

!Depending on the cellular phone, phone book transfer may not be available.

phoning free-hands Using

En 91

Chapter

 

 

 

 

 

 

13

Customizing preferences

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The options in the “Navi

 

Indicates the connection status of the GPS

 

Settings” menu

 

antenna, the reception sensitivity, and from

 

 

how many satellites the signal is received.

 

 

 

 

 

Displaying the “Navi Settings”

 

 

 

 

 

 

Color

Signal com-

Used in posi-

 

screen

 

 

 

munication

tioning

 

 

 

 

1 Press the HOME button to display the

 

Orange

Yes

Yes

 

“Top Menu”.

 

 

 

 

 

 

Yellow

Yes

No

 

 

 

 

2

Touch [Settings].

 

 

 

 

 

p When the GPS antenna is connected to

 

The “Settings Menu” screen appears.

 

 

this navigation system, [OK] is dis-

 

 

 

 

3

Touch [Navi Settings].

 

played.

 

 

 

 

The “Navi Settings” menu appears.

 

When the GPS antenna is not con-

 

 

 

 

nected to this navigation system, [NOK]

 

 

 

 

is displayed.

 

 

 

 

 

p If reception is poor, please change the

 

 

 

 

installation position of the GPS antenna.

 

 

 

3 Parking Brake

 

 

 

 

 

 

When the parking brake is applied, [On] is

 

 

 

 

displayed. When the parking brake is re-

 

 

 

 

leased, [Off] is displayed.

 

 

 

 

 

4 Power Voltage

 

 

 

 

 

 

The power voltage (reference value) pro-

 

Checking the connections of leads

 

vided from the vehicle battery to the naviga-

 

 

tion system is shown. If the voltage goes

 

Check that leads are properly connected be-

 

 

 

out of the range from 11 V to 15 V, check

 

tween the navigation system and the vehicle.

 

that power cable connection is correct.

 

Please also check whether they are connected

5 Illumination

 

 

 

 

in the correct positions.

 

When the headlights or small lamps of a ve-

 

1 Display the “Navi Settings” screen.

 

hicle are on, [On] is displayed. When the

 

 

small lamps of a vehicle are off, [Off] is dis-

 

 

 

 

2

Touch [Connection Status].

 

played. (If the orange/white lead is not con-

 

The “GPS Status” screen appears.

 

nected, [Off] appears.)

 

 

 

 

 

6 Back Signal

 

 

 

When the gear lever is shifted to “R”, the

1

 

signal switches to [High] or [Low]. (One of

 

2

 

 

these is displayed depending on the vehi-

3

 

 

cle.)

4

 

 

 

5

 

Checking sensor learning

 

6

 

 

 

 

 

 

status and driving status

1Speed Pulse

The Speed Pulse value detected by the navigation system is shown. [0] is shown while the vehicle is stationary.

2GPS ANT

pThe navigation system can automatically use its sensor memory based on the outer dimensions of the tires.

1 Display the “Navi Settings” screen.

92 En

Customizing preferences

2 Touch [3D Calibration Status].

 

 

Clearing status

The “3D Calibration Status” screen appears.

You can delete the learned results stored in

 

 

 

 

 

 

 

 

 

6

[Distance], [Speed Pulse] or [Learning Sta-

1

 

 

 

 

 

 

 

 

7

tus].

 

 

 

 

 

 

 

 

1 Touch [Distance] or [Speed Pulse].

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

 

 

 

 

 

 

 

 

 

The following message appears.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1Speed

The speed detected by the navigation system is indicated. (This indication may be different from the actual speed of your vehicle, so please do not use this instead of the speedometer.)

2Acceleration or deceleration/Rotational speed

Acceleration or deceleration velocity of your vehicle is indicated. Also, rotational speed when your vehicle turns to left or right is shown.

3Distance

Driving distance is indicated.

4Speed Pulse

Total number of speed pulses is indicated.

5Learning Status

Current driving mode is indicated.

6Inclination

Degree of slope of the street that you are currently running is indicated.

7Degree of learning

Sensor learning situations for distance (Distance), right turn (Right Turn), left turn (Left Turn) and 3D detection (3D) are indicated by the length of bars.

p When tires have been changed or chains fitted, turning on the Speed Pulse allows the system to detect the fact that the tire diameter has changed, and automatically replaces the value for calculating distance.

p If ND-PG1 is connected, the distance calculation value cannot be replaced automatically.

2 Touch [Yes].

Clears the learned results stored in [Distance] or [Speed Pulse].

3 Touch [Learning Status].

The following message appears.

4 Touch [All].

Clears all learning statuses.

pTouch [All] for the following cases:

After changing the installation position of the navigation system

After changing the installation angle of the navigation system

After moving the navigation system to another vehicle

#Touch [Distance].

Clears the learned results stored in [Distance].

pWhen the distance accuracy is low, touch [Distance].

Chapter

13

preferences Customizing

En 93

Chapter

13 Customizing preferences

Using the “Gas Mileage” function

Inputting the fuel consumption information for calculating the fuel cost

You can estimate the fuel cost to your destination by entering the fuel consumption information in the navigation system.

![Gas Unit]:

Set the fuel unit.

![Currency]:

Set the unit of currency.

When all the items are entered, inputting the fuel consumption information is complete.

1Display the “Navi Settings” screen.

2Touch [Gas Mileage].

The “Gas Mileage Setting” screen appears.

Entering the fueling information

When you enter the fueling information to the navigation system, and export the data to SD memory cards, you can check the fuel consumption information by using the utility program “AVIC FEEDS” which is available separately, on your PC.

pUp to 24 sets of “Gas Price Calculation” entries can be stored. You can also export the data, as described below.

If the entries reach the maximum number, a new entry will overwrite the oldest one.

3 Enter the fuel consumption information.

Enter the following items:

![Surface Road Gas Mileage]:

Enter the fuel cost when you drive on ordinary roads.

p How the fuel cost is entered depends on the [Gas Unit] setting.

When [Gas Unit] is set to [Gallon]. Enter how many miles (kilometers) you get to a gallon.

When [Gas Unit] is set to [Liter]. Enter how much fuel you need to travel 60 miles (100 kilometers).

![Freeway Gas Mileage]:

Enter the fuel cost when you drive on the freeway.

p How the fuel cost is entered depends on the [Gas Unit] setting.

When [Gas Unit] is set to [Gallon]. Enter how many miles (kilometers) you get to a gallon.

When [Gas Unit] is set to [Liter]. Enter how much fuel you need to travel 60 miles (100 kilometers).

![Gas Price Per Unit]: Enter the fuel unit price.

Gas Mileage Management function only assists you to calculate your average mileage based on the information you input. The function does not receive data directly from the vehicle.

1Display the “Navi Settings” screen.

2Touch [Gas Mileage].

The “Gas Mileage Setting” screen appears.

3 Touch [Gas Price Calculation].

The “Gas Price Calculation” screen appears.

94 En

 

Chapter

Customizing preferences

13

 

 

4Enter the following settings:

![Distance]:

Enter the distance traveled since the previous fueling.

p The distance is entered automatically only when the distance traveled since the previous fueling is recorded.

![Gas Pumped]:

Enter the amount of fuel pumped.

![Gas Price Per Unit]: Enter the fuel unit price.

When all the items are entered, the fuel consumption is displayed next to “Gas Mileage”.

5 Touch [OK].

The “Gas Mileage Setting” screen appears.

Exporting the data of “Gas Mileage Management”

Exporting the “Gas Mileage Management” data to an SD memory card is possible.

pThe data stored in this navigation system will be cleared as exporting it to the SD memory card.

pIf there is a previous data in the SD memory card, the data is overwritten with new data when current data is exported.

1Insert an SD memory card into the SD card slot.

=For more details of the operation, refer to Inserting and ejecting an SD memory card on page 29.

2Display the “Navi Settings” screen.

3Touch [Gas Mileage].

The “Gas Mileage Setting” screen appears.

4 Touch [Export].

After a message confirming whether to export the data appeared, exporting the data to the SD memory card starts.

The “Gas Mileage Setting” screen appears when it is done.

Recording your travel history

Activating the track logger enables you to record your driving history (called “track log” below). You can review the travel history later.

pIf an SD memory card is inserted into the SD card slot, the track logs will be stored in the SD memory card.

1Insert an SD memory card into the SD card slot.

=For more details of the operation, refer to Inserting and ejecting an SD memory card on page 29.

2Display the “Navi Settings” screen.

3Touch [Drive Log Settings].

The “Drive Log Settings” screen appears.

4 Touch [Drive Log Settings].

Each time you touch the key changes that setting.

preferences Customizing

En 95

Chapter

13 Customizing preferences

![On]:

You can export your track log to the SD card.

![Off] (default):

You cannot export your track log to the SD card.

#Touch [Type].

Each time you touch the key changes that setting.

![Private] (default):

Set the track log attribute to “Private”.

![Business]:

Set the track log attribute to “Business”.

![Other]:

Set the track log attribute to “Other”.

pWhile the setting is [On], the navigation system continues to store the track logs in the inserted SD memory card.

Using the demonstration guidance

This is a demonstration function for retail stores. After a route is set, touching this key starts the simulation of route guidance.

1Display the “Navi Settings” screen.

2Touch [Demo Mode].

Each time you touch the key changes that setting.

![On]:

Repeat demo drive.

![Off] (default):

2 Touch [Set Home].

The “Set Home” screen appears.

3 Touch [Home].

The “Select Search method” screen appears.

# Touch [Phone #].

When you have already registered your home, you can edit your home number.

4 Search for a location.

After searching for a point, display it on a map, then touch [OK].

The location is registered, and then the “Set Home” screen appears.

= For details, refer to Chapter 8.

5 Touch [OK].

The registration is completed.

Correcting the current location

Touch the screen to adjust the current position and direction of the vehicle displayed on the map.

Demo Mode is set off.

3 Display the map screen.

The demonstration guidance will begin.

Registering your home

Registering your home position saves time and effort. Also, routes to home positions can be calculated easily with a single touch of the key from the “Destination Menu”. The registered home position can also be modified later.

1 Display the “Navi Settings” screen.

1Display the “Navi Settings” screen.

2Touch [Modify Current Location].

3Scroll to the position where you want to set, then touch [OK].

Options on the “System Settings” menu

Displaying the “System

Settings” screen

1 Press the HOME button to display the “Top Menu”.

96 En

Customizing preferences

2 Touch [Settings].

The “Settings Menu” screen appears.

3 Touch [System Settings].

The “System Settings” screen appears.

Customizing the regional settings

1Display the “System Settings” screen.

2Touch [Regional Settings].

The “Regional Settings” screen appears.

Selecting the language

You can set the languages used on the program and voice guidance. Each language can be set separately.

1Display the “Regional Settings” screen.

2Touch [Program Language].

The language list is displayed.

3 Touch the desired language.

After the language is selected, the screen returns to the previous screen.

4 Touch [Voice Language].

The “Voice Language Selection” screen appears.

5 Touch the desired language.

After the language is selected, the screen returns to the previous screen.

6Touch [OK] on the “Regional Settings” screen.

A message confirming whether to restart the navigation system appears.

7Touch [OK].

The navigation system restarts.

# Press the MODE button or the HOME button. Cancels the setting of the languages.

Setting the time difference

Adjusts the systems clock. Set the time difference (+, –) from the time originally set in your navigation system.

1Display the “Regional Settings” screen.

2Touch [Time].

The “Time Settings” screen appears.

3To set the time difference, touch [+] or

[–].

The time difference between the time originally set in the navigation system (Pacific Standard Time) and the current location of your vehicle is shown. If necessary, adjust the time difference. Touching [+] or [–] changes the time difference display in one-hour increments.

The time difference can be set from –4 to +9 hours.

4Touch [Summer Time].

If necessary, set to summer time.

Chapter

13

preferences Customizing

En 97

Chapter

13 Customizing preferences

Summer time is off by default. Touch [Summer Time] to change the time if you are in the summer time period. This turns the display below summer time [On].

5 Touch [Time format].

Each time you touch the key changes that setting.

![12H] (default):

Switching the display for 12 hours with am/ pm.

![24H]:

Switching the display for 24 hours.

Changing the unit between km and miles

This setting controls the unit of distance and speed displayed on your navigation system.

1Display the “Regional Settings” screen.

2Touch [km / mile].

A message confirming whether to change the setting appears.

3 Touch [Yes].

It changes the settings as follows:

![mile] (default):

Show distance in miles.

![Mile&Yard]:

Show distance in miles and yards.

![km]:

Show distance in kilometers.

#Touch [No].

Cancels the setting.

Changing the virtual speed of the vehicle

When calculating the expected time of arrival and the number of hours to the destination, set the average speed for the freeway or ordinary roads using [+] and [–].

1Display the “Regional Settings” screen.

2Touch [Speed].

The “Average Speed Settings” screen appears.

3 Touch [+] or [–] to set the speed.

pThe estimated time of arrival is not necessarily estimated based on this speed value.

4 Touch [OK].

The settings are completed.

Setting the Volume for

Guidance and Phone

The sound volume for the navigation can be set. You can separately set the volume of the route guidance and the beep sound.

1Display the “System Settings” screen.

2Touch [Volume].

The “Volume Settings” screen appears.

3 Touch the key next to “Beep”.

Each time you touch the key changes that setting.

![On] (default): A beep sounds.

![Off]:

Muting the beep sound.

4 Touch [+] or [–] to set their volume.

On this screen, you can operate the following items.

! [Guidance]

98 En

 

Chapter

Customizing preferences

13

 

 

This setting controls the guidance volume of navigation.

pWhen set to , guidance is output. When set to , no guidance is output.

![Phone Ringtone]

This setting controls the incoming ring tone volume.

![Phone Voice]

This setting controls the incoming voice volume.

pPhone Ringtone and Phone Voice adjustments are related to the cellular phone featuring Bluetooth technology. No adjustment is needed when the cellular

phone featuring Bluetooth technology is not connected.

pVolume of the AV source is adjusted by VOL (+/–) button.

=For details, refer to Checking part names and functions on page 27.

5 To finish the setting, touch [OK].

Changing the splash screen

You can change the splash screen to the other images stored in the navigation system.

1Display the “System Settings” screen.

2Touch [Splash Screen].

The “Select Splash Screen” screen appears.

3Touch the image to use as the splash screen from the list.

The image is displayed on the screen.

4Touch [OK].

The image is set as the splash screen, and the system returns to the “System Settings” menu.

pSplash screen images should be used within the following formats;

BMP or JPEG files

Allowable horizontal and vertical size are 2 592 pixels x 1 944 pixels or smaller

Allowable data size is 6 MB or smaller

pProper compatibility with allowable files is not guaranteed.

pImported original images will be stored in the built-in memory, but the ability to save these images cannot be guaranteed completely. If your original image data is deleted, insert the SD memory card again and re-import the original image.

1Create a folder named “Pictures” on the top-most directory of the SD memory card and store the picture files in this folder.

2Store the picture files in “Pictures”.

3Insert an SD memory card into the SD card slot.

=For more details of the operation, refer to Inserting and ejecting an SD memory card on page 29.

4Display the “System Settings” screen.

5Touch [Splash Screen].

The “Select Splash Screen” screen appears.

6 Touch [Select from SD].

The “Select Splash Screen” screen appears.

7Touch the image to use as the splash screen from the list.

The image is displayed on the screen.

8Touch [OK].

The image is set as the splash screen, and the system returns to the “System Settings” menu.

preferences Customizing

Changing to the splash screen stored in the SD memory card

You can change the splash screen that appears when the navigation system starts. Copy your chosen image to the SD memory card, and select the image to import.

Setting for rear view camera

The following two functions are available. The rear view camera feature requires a separately sold rear view camera (e.g. ND-BC2). (For details, consult your dealer.)

En 99

Chapter

13 Customizing preferences

Rear view camera

The navigation system features a function that automatically switches to the full-screen rear view camera image installed on your vehicle. When the shift lever is in the REVERSE (R) position, the screen automatically switches to full-screen rear view camera.

Camera for Rear view mode

[Rear View] can be displayed at all times (e.g. when monitoring an attached trailer, etc.) as a split screen where map information is partially displayed. Please be aware that with this setting, camera image is not resized to fit, and that a portion of what is seen by the camera is not viewable.

CAUTION

Pioneer recommends the use of a camera which outputs mirror reversed images, otherwise the screen image may appear reversed.

Adjusting the response positions of the touch panel (touch panel calibration)

If you feel that the touch panel keys on the screen deviate from the actual positions that respond to your touch, adjust the response positions of the touch panel screen.

pDo not use a sharp pointed tool such as a ballpoint pen or a mechanical pen, which could damage the screen.

1Display the “System Settings” screen.

2Touch [Screen Calibration].

A message confirming whether to start the calibration appears.

3 Gently touch the center of + mark displayed on the screen.

The target indicates the order.

After you touch all marks, the adjusted position data is saved.

pImmediately verify whether the display changes to a rear view camera image when

the shift lever is moved to REVERSE (R) from another position.

pWhen the screen changes to full-screen rear view camera image during normal driving, switch to the opposite setting in [Polarity].

1Display the “System Settings” screen.

2Touch [Back Camera].

The “Back Camera Settings” screen appears.

3 Touch [Camera] to turn it [On].

pYou can only switch to “Rear View” if this setting is [On].

4 Touch [Battery] or [GND] next to “Polarity” to select the appropriate polarity setting.

!Battery — When the polarity of the connected lead is positive while the shift lever is in the REVERSE (R) position

!GND — When the polarity of the connected lead is negative while the shift lever is in the REVERSE (R) position

pDo not turn off the engine while saving the adjusted position data.

#Press the MODE button.

Returns to the previous adjustment position.

# Press and hold the MODE button. Cancels the adjustment.

Setting the illumination color

The illumination color can be selected from 11 different colors. Furthermore, the illumination color can switched between these 11 colors in order.

To set the illumination color, display the “Illumination Color” screen.

1Display the “System Settings” screen.

2Touch [Illumi Color].

The “Illumination Color” screen appears.

100 En