Pioneer PDP-428XG, PDP-508XG User Manual

Name: Pioneer PDP-428XG
Brand: Pioneer
SKU: 565030
Rating: 5 (1 reviews)

5 (1)

Operating Instructions | Manual de instrucciones |

Manual de instruções | |

PLASMA TELEVISION

TELEVISOR DE PLASMA

PDP-

508

PDP-

428

To use your plasma television for a long period of time

Cautions regarding screen burning

After-image lagging:

When characters, images or images of fixed patterns with very high luminance are displayed on a plasma television screen, even if displayed for a relatively

short period of time, the image may remain on the screen due to the residual electric load of the panel. However, this is not a malfunction. This after-image

lagging can be eliminated gradually by displaying moving images in full screen.

Burning:

When images like those described above are displayed continuously for a long period of time or repeatedly, a difference occurs between the luminance of

the continuously displayed image and that of other portions of the screen, resulting in the image remaining on the screen due to burning. Please note that

if this burning occurs, it may be difficult to completely restore the screen to the state prior to burning. It should also be noted that this phenomenon

tends to occur more easily soon after the product is purchased.

• If programs such as terrestrial digital broadcasts having a screen size of 4:3 are viewed

repeatedly, the normal display area other than the black bands on the left and right sides

of the screen becomes susceptible to burning.

• If cinema-size images are repeatedly viewed in their original size, the normal display area

other than the black bands at the top and bottom of the screen becomes susceptible to

burning.

• If programs containing a time display or station name displayed on the screen are viewed

for a long period of time (or viewed repeatedly), the displayed characters may be easily

burned onto the screen.

• If images of fixed patterns such as those of personal computer displays or game software are displayed for a long period of time, the patterns may be

easily burned onto the screen.

It is recommended to use your plasma television while paying attention to the matters described below, particularly when using the product soon after it

has been purchased, to prevent screen burning.

• Avoid using the product while displaying images susceptible to burning as described above whenever possible.

• Use the product with the Orbiter function set to “On”

(

⇒ see Useful adjustment settings: “Orbiter”).

• When viewing programs broadcast in a 4:3 or cinema screen size, switch the screen size with the remote control unit to display the image in full screen.

(Change the screen size to “WIDE”, for example, with the screen size button on the remote control unit (

⇒ see Part names: “Remote control unit”)).

• Set the Side Mask detection function to “On” (

⇒ see Useful adjustment settings: “Detecting side masks”).

• Set the brightness of the side masks

that appear on the left and right sides of the screen when viewing at a 4:3 screen size to “Auto” in “Brightness Sync.”

(

⇒ see Useful adjustment settings: “Changing the brightness at both sides of the screen (Side Mask)”).

• It is recommended to lower the brightness when viewing by setting the Energy Sav

e function to “Mode 1” (⇒ see Setting up: “Power Control”).

After-image lagging and screen burning

Display examples susceptible to burning

Preventing burning

15:00 PROTV

WARNING

This equipment is not waterproof. To prevent a fire or shock

hazard, do not place any container filed with liquid near this

equipment (such as a vase or flower pot) or expose it to

dripping, splashing, rain or moisture.

D3-4-2-1-3_A_En

WARNING

This product equipped with a three-wire grounding

(earthed) plug - a plug that has a third (grounding) pin.

This plug only fits a grounding-type power outlet. If you are

unable to insert the plug into an outlet, contact a licensed

electrician to replace the outlet with a properly grounded

one. Do not defeat the safety purpose of the grounding

plug.

D3-4-2-1-6_A_En

WARNING

Before plugging in for the first time, read the following section

carefully.

The voltage of the available power supply differs according

to country or region. Be sure that the power supply voltage

of the area where this unit will be used meets the required

voltage (e.g., 230V or 120V) written on the rear panel.

D3-4-2-1-4_A_En

The following symbols are found on labels

attached to the product. They alert the operators

and service personnel of this equipment to any

potentially dangerous conditions.

WARNING

This symbol refers to a hazard or unsafe

practice which can result in personal injury

or property damage.

CAUTION

This symbol refers to a hazard or unsafe

practice which can result in severe personal

injury or death.

WARNING

To prevent a fire hazard, do not place any naked flame

sources (such as a lighted candle) on the equipment.

D3-4-2-1-7a_A_En

VENTILATION CAUTION

When installing this unit, make sure to leave space around

the unit for ventilation to improve heat radiation. For the

minimum space required, see page 15.

WARNING

Slots and openings in the cabinet are provided for

ventilation to ensure reliable operation of the product, and

to protect it from overheating. To prevent fire hazard, the

openings should never be blocked or covered with items

(such as newspapers, table-cloths, curtains) or by operating

the equipment on thick carpet or a bed.

STANDBY/ON Button

STANDBY:

When placed into the standby mode, the main power

flow is cut and the unit is no longer fully operational.

STANDBY/ON Indicator: The indicator is lit red when the unit

is in the standby mode and is lit blue when it is in the power-on

mode.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

CAUTION:

TO PREVENT THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT

D3-4-2-1-1_En-A

Operating Environment

Operating environment temperature and humidity:

+0 °C to +40 °C (+32 °F to +104 °F); less than 85 %RH

(cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in

locations exposed to high humidity or direct sunlight (or

strong artificial light)

D3-4-2-1-7c_A_En

CAUTION

The  switch on this unit will not completely shut off all power

from the AC outlet. Since the power cord serves as the main

disconnect device for the unit, you will need to unplug it from

the AC outlet to shut down all power. Therefore, make sure the

unit has been installed so that the power cord can be easily

unplugged from the AC outlet in case of an accident. To avoid

fire hazard, the power cord should also be unplugged from the

AC outlet when left unused for a long period of time (for

example, when on vacation).

D3-4-2-2-2a_A_En

English

Contents

Thank you for buying this Pioneer product.

Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading

the instructions, put them away in a safe place for future reference.

In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown in the explanatory

drawings. However the method of connecting and operating the unit are the same.

Contents

01 Important user information. . . . . . . . . . . . . . . . . 6

02 Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . 9

Installation precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

03 Supplied accessories . . . . . . . . . . . . . . . . . . . . . . 11

04 Part names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Plasma television. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Remote control unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

05 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Installing the plasma television . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Moving the plasma television . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Preventing the plasma television from falling over. . . . . . . . . . . . 16

Basic connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Preparing the remote control unit . . . . . . . . . . . . . . . . . . . . . . . . . 18

Operating range of the remote control unit . . . . . . . . . . . . . . . . . 18

06 Watching TV. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Turning the power on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Placing the system into standby . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Changing channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Changing the volume and sound . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Switching the broadcast audio channel . . . . . . . . . . . . . . . . . . . . 21

Using the multiscreen functions . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Freezing images. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

07 The HOME MENU . . . . . . . . . . . . . . . . . . . . . . . . . 23

HOME MENU overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Using the HOME MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

08 Setting up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Setting up TV channels automatically . . . . . . . . . . . . . . . . . . . . . .25

Setting up TV channels manually . . . . . . . . . . . . . . . . . . . . . . . . . .25

Reducing video noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Setting Child Lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Suppressing audio distortion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Labeling TV channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Sorting preset TV channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Language setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

AV Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Basic picture adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Advanced picture adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Comparing picture adjustments on the screen . . . . . . . . . . . . . . .32

Sound adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Listening to audio from the sub screen using headphones . . . . .33

Power Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

09 Useful adjustment settings . . . . . . . . . . . . . . . . 36

Switching the vertical drive mode

(AV source only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Adjusting image positions (AV source only) . . . . . . . . . . . . . . . . .36

Adjusting image positions and clock automatically

(PC source only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Adjusting image positions and clock manually

(PC source only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Color system setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Selecting a game mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Selecting a screen size manually . . . . . . . . . . . . . . . . . . . . . . . . . .37

Selecting a screen size automatically. . . . . . . . . . . . . . . . . . . . . . .38

Detecting side masks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Changing the brightness at both sides of the screen

(Side Mask) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Room Light Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Blue LED Dimmer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Orbiter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Video Pattern. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Using a password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Illustrations shown in this manual are for the PDP-508XG unless otherwise specified.

Contents

English

10 Using with other equipment. . . . . . . . . . . . . . . .42

Connecting a digital tuner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Connecting a DVD player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Connecting a VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Connecting a game console or camcorder . . . . . . . . . . . . . . . . . . 43

Connecting a personal computer. . . . . . . . . . . . . . . . . . . . . . . . . . 44

Connecting an amplifier/AV receiver . . . . . . . . . . . . . . . . . . . . . . . 44

Avoiding unwanted feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Using the HDMI Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Using control cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Enjoying through USB interface (Home Gallery function) . . . . . . 48

Controlling other equipment using the supplied remote

control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

11 Using the HDMI Control. . . . . . . . . . . . . . . . . . . .56

Using the HDMI Control functions. . . . . . . . . . . . . . . . . . . . . . . . . 56

Making the HDMI Control connections . . . . . . . . . . . . . . . . . . . . . 57

Setting the HDMI Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Using the HDMI Control menus . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

12 Using Teletext. . . . . . . . . . . . . . . . . . . . . . . . . . . .61

Using the Teletext Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Operating the Teletext basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

13 Additional information . . . . . . . . . . . . . . . . . . . .63

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Signal assignments for 15-pin D-sub connector. . . . . . . . . . . . . . 65

Standard channel allocation selections for countries

and regions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Important user information

Chapter 1

Important user information

In order to obtain maximum enjoyment from this Pioneer PDP-

508XG/PDP-428XG plasma television, please first read this

information carefully.

With the Pioneer PDP-508XG/PDP-428XG, you can be assured of a

high quality plasma television with long-life and high reliability. To

achieve images of exceptional quality, this Pioneer plasma

television incorporates state-of-the-art design and construction, as

well as very precise and highly advanced technology.

The Pioneer PDP-508XG/PDP-428XG incorporates the latest in

color filter technology: Direct Color Filter. This improves the color/

picture reproduction of these models as compared to previous

models. It also eliminates the need for a physical glass panel to be

placed in front of the plasma panel, which furthers Pioneer’s

continued goal of reducing environmental waste in consumer

electronics, now during the manufacturing process and in the

future during the recycling process.

Over the course of its lifetime, the luminosity of the Pioneer PDP-

508XG/PDP-428XG plasma television will diminish very slowly,

such as with all phosphor-based screens (for example, a traditional

tube-type television). To enjoy beautiful and bright images on your

Pioneer plasma television for a long time, please carefully read and

follow the usage guidelines below:

Usage guidelines

All phosphor-based screens (including conventional tube-type

televisions) can be affected by displaying static images for a

prolonged period. Plasma televisions are no exception to this rule.

After-image and permanent effects on the screen can be avoided

by taking some basic precautions. By following the

recommendations listed below, you can ensure longer and

satisfactory results from your plasma television:

• Whenever possible, avoid frequently displaying the same

image or virtually still moving pictures (e.g. video game images

which have static portions).

• Do not display Teletext for a prolonged period of time.

• Avoid viewing the On Screen Display for extended periods,

from a digital tuner, DVD player, VCR and all other

components.

• Do not leave the same picture freeze-framed or paused

continuously over a long period of time, when using the still

picture mode from a TV, VCR, DVD player or any other

component.

• Images which have both very bright areas and very dark areas

side by side should not be displayed for a prolonged period of

time.

• When playing a game, the “GAME” mode setting within “AV

Selection” is strongly recommended. However, please do not

use this mode for long periods of time.

• After playing a game, displaying a PC image or any still image,

it is best to view a normal moving picture in the “WIDE” or

“FULL” screen setting for more than three times the length of

the previous still/moving image.

• After using the plasma television, always switch the display to

“STANDBY” mode.

Installation guidelines

The Pioneer PDP-508XG/PDP-428XG plasma television

incorporates a very thin design. To ensure safety, please take the

proper measures to mount or install the plasma television, in order

to prevent the unit from tipping over in the event of vibration or

accidental movement.

This product should be installed by using only parts and

accessories designed by Pioneer. Use of accessories other than

the Pioneer stand or installation bracket may result in instability,

and could cause injury. For custom installation, please consult the

dealer where the unit was purchased. To ensure correct

installation, experienced and qualified experts must install the unit.

Pioneer will not be held responsible for accident or damage caused

by the use of parts and accessories manufactured by other

companies.

To avoid malfunction and overheating, make sure that the vents on

the main unit are not blocked when installing to ensure proper heat

emission:

• Distance the unit slightly from other equipment, walls, etc. For

the minimum space required around the unit, see page 15.

• Do not fit the unit inside narrow spaces where ventilation is

poor.

• Do not cover with a cloth, etc.

• Clean the vents on the sides and rear of the unit to remove dust

build-up, by using a vacuum cleaner set to its lowest suction

setting.

• Do not place the product on a carpet or blanket.

• Do not leave the product tilted over.

• Do not turn the product upside down.

Using the unit without proper ventilation may cause the internal

temperature to rise, and could result in possible malfunction.

When the surrounding or internal temperature exceeds a certain

degree, the display will automatically power off in order to cool the

internal electronics and prevent hazardous occurrences.

Any malfunction may occur due to: an inappropriate installation

site, improper assembly, installation, mounting, or operation of

this product, modifications made to the product. However, Pioneer

cannot be held responsible for such accidents or malfunction.

Note

The following are typical effects and characteristics of a

phosphor-based matrix display and as such, are not covered by

the manufacturer’s limited warranties:

• Permanent residual images upon the phosphors of the panel.

• The existence of a minute number of inactive light cells.

• Panel generated sounds, examples: Fan motor noise, and

electrical circuit humming/glass panel buzzing

Caution

• Pioneer bears no responsibility for any damage arising from

incorrect use of the product by you or other people,

malfunctions when in use, other product related problems, and

use of the product except in cases where the company must be

liable.

Important user information

English

Plasma television protection function

When still images (such as photos and computer images) stay on

the screen for an extended period of time, the screen will be slightly

dimmed. This is because the protection function of the plasma

television automatically adjusts the brightness to protect the

screen when detecting still images; so this does not designate

malfunction. The screen is dimmed when a still image is detected

for about three minutes.

Information of pixel defect

Plasma television displays information using pixels. Pioneer

plasma television panels contain a very large number of pixels.

(Depending on the panel size: over 2.3 million cells in case of a 42

inch display; over 3.1 million cells in the case of a 50 inch display).

All Pioneer display panels are manufactured using a very high level

of ultra-precision technology and undergo individual quality

control.

In rare cases, some pixels can be permanently switched off, or on,

resulting in either a black or colored pixel permanently fixed on the

screen.

This effect is common to all plasma television because it is a

consequence of the technology.

If the defective pixels are visible at a normal viewing distance of

between 2.5 meters and 3.5 meters while viewing a normal

broadcast (i.e. not a test card, still image or single color display)

please contact the supplying dealer.

If, however, they can only be seen close up or during single color

displays then this is considered normal for this technology.

Infrared rays

The plasma television releases infrared rays because of its

characteristics. Depending on how the plasma television is in use,

the remote controls of nearby equipment may be adversely affected

or wireless headphones using infrared rays are interfered by noise.

If this is the case, place that equipment at a location where its

remote control sensor is not affected.

Radio interference

While this product meets the required specifications, it emits a

small amount of noise. If you place such equipment as an AM

radio, personal computer, and VCR close to this product, that

equipment may be interfered. If this happens, place that

equipment far enough from this product.

Plasma television driving sound

The screen of the plasma television is composed of extremely fine

pixels and these pixels emit light according to received video

signals. This principle may make you hear buzz sound or electrical

circuit humming from the plasma television.

Do not attach such items as labels and tape to the product

This may result in the discoloration or scratch of the cabinet.

When not using the product for a long period of time

If you do not use the product for a long period of time, the functions

of the product may be adversely affected. Switch on and run the

product occasionally.

Condensation

Condensation may take place on the surface or inside of the

product when the product is rapidly moved from a cold place to a

warm place or just after a heater is switched on in winter morning,

for example. When condensation takes place, do not switch on the

product and wait until condensation disappears. Using the product

with condensation may result in malfunction.

Cleaning the surface of the screen and the glossy surface

of the front cabinet

When cleaning the surface of the screen or the glossy surface of

the front cabinet, gently wipe it with a dry soft cloth; the supplied

cleaning cloth or other similar cloths (e.g., cotton and flannel). If

you use a dusty or hard cloth or if you rub the screen hard, the

surface of the product will be scratched.

If you clean the surface of the screen with a wet cloth, water

droplets on the surface may enter into the product, resulting in

malfunction.

Cleaning the cabinet

When cleaning the cabinet of this product, gently wipe it with a

clean soft cloth (e.g., cotton and flannel). If you use a dusty or hard

cloth or if you rub the cabinet hard, the surface of the cabinet will

be scratched.

The cabinet of this product is mostly composed of plastic. Do not

use chemicals such as benzene or thinner to clean the cabinet.

Using these chemicals may result in quality deterioration or

coating removal.

Do not expose the product to volatile gas or fluid such as pesticide.

Do not make the product contact with rubber or vinyl products for

a long period of time. The effect of plasticizer in the plastic may

result in quality deterioration or coating removal.

If you clean the surface of the cabinet with a wet cloth, water

droplets on the surface may enter into the product, resulting in

malfunction.

Handles at the rear of the plasma television

Do not remove the handles from the rear of the plasma television.

When moving the plasma television, ask another person for help

and use the handles attached to the rear of the plasma television.

Do not move the plasma television by holding only a single handle.

Do not use the handles to hang the product when installing or

carrying the product, for example. Do not use the handles for the

purpose of preventing the product from tilting over.

Fan noise

The rotation speed of the cooling fan motor increases when the

ambient temperature of the plasma television becomes high. You

may hear the sound of the fan motor at that time.

Important user information

To use this product for a long period of time

The Energy Save function can maintain efficiency of the screen for

a long period of time. Setting the Energy Save function to “Mode 1”

is recommended in order to maintain the efficiency of the screen

for a long period of time.

Caution

Panel sticking and after-image lag

Displaying the same images such as still images for a long time

may cause after-image lagging. This may occur in the following two

cases.

After-image lagging due to remaining electrical load

When image patterns with very high peak luminance are displayed

for more than one minute, after-image lagging may occur due to

the remaining electric load. The after-images remaining on the

screen will disappear when moving images are displayed. The time

for the after-images to disappear depends on the luminance of the

still images and the time they had been displayed.

After-image (lag image) due to burning

Avoid displaying the same image on the plasma television

continuously over a long period of time.

If the same image is displayed continuously for a long period, or for

shorter periods of time over several days, a permanent after-image

may remain on the screen due to burning of the fluorescent

materials. Such images may become less noticeable if moving

images are later displayed, but they will not disappear completely.

Note

• When a still image, such as a program menu, is displayed for

5 to 10 minutes, the system automatically turns the image off

to prevent damage from screen burning.

• To prevent screen burning, the display position is automatically

changed imperceptibly when watching plasma television (see

Orbiter on page 39).

Preventing damage from screen burning

• We recommend that you enjoy watching images displayed in

full screen, except when doing so may result in copyright

infringement (see page 37).

• Set the Side Mask detection function to “On”, the High

Definition 16:9 aspect ratio images containing side masks will

be detected and the side masks will be added automatically or

the image displayed in full screen, leading to more effective

countermeasures taken for the screen burning (see Detecting

side masks on page 38).

Safety precautions

English

Chapter 2

Safety precautions

Electricity is used to perform many useful functions, but it can also

cause personal injuries and property damage if improperly

handled. This product has been engineered and manufactured

with the highest priority on safety. However, improper use can

result in electric shock and/or fire. In order to prevent potential

danger, please observe the following instructions when installing,

operating and cleaning the product. To ensure your safety and

prolong the service life of your product, please read the following

precautions carefully before using the product.

1. Read instructions - All operating instructions must be read and

understood before the product is operated.

2. Keep this manual in a safe place - These safety and operating

instructions must be kept in a safe place for future reference.

3. Observe warnings - All warnings on the product and in the

instructions must be observed closely.

4. Follow instructions - All operating instructions must be followed.

5. Cleaning - Unplug the power cord from the AC outlet before

cleaning the product. To clean the product, use the supplied

cleaning cloth or other soft clothes (e.g., cotton, flannel). Do not

use liquid cleaners or aerosol cleaners.

6. Attachments - Do not use attachments not recommended by the

manufacturer. Use of inadequate attachments can result in

accidents.

7. Water and moisture - Do not use the product near water, such as

bathtub, washbasin, kitchen sink and laundry tub, swimming pool

and in a wet basement.

8. Stand - Do not place the product on an unstable cart, stand, tripod

or table. Placing the product on an unstable base can cause the

product to fall, resulting in serious personal injuries as well as

damage to the product. Use only a cart, stand, tripod, bracket or

table recommended by the manufacturer or sold with the product.

When mounting the product on a wall, be sure to follow the

manufacturer’s instructions. Use only the mounting hardware

recommended by the manufacturer.

9. When relocating the product placed on a cart, it must be moved

with utmost care. Sudden stops, excessive force and uneven floor

surface can cause the product to fall from the cart.

10. Ventilation - The vents and other openings in the cabinet are

designed for ventilation. Do not cover or block these vents and

openings since insufficient ventilation can cause overheating and/

or shorten the life of the product. Do not place the product on a

bed, sofa, rug or other similar surface, since they can block

ventilation openings. This product is not designed for built-in

installation; do not place the product in an enclosed place such as

a bookcase or rack, unless proper ventilation is provided or the

manufacturer’s instructions are followed.

11. Power source - This product must operate on a power source

specified on the specification label. If you are not sure of the type

of power supply used in your home, consult your dealer or local

power company.

12. Power cord protection - The power cords must be routed properly

to prevent people from stepping on them or objects from resting on

them. Check the cords at the plugs and product.

13. The plasma television used in this product is made of glass.

Therefore, it can break when the product is dropped or applied with

impact. Be careful not to be injured by broken glass pieces in case

the plasma television breaks.

14. Overloading - Do not overload AC outlets or extension cords.

Overloading can cause fire or electric shock.

15. Entering of objects and liquids - Never insert an object into the

product through vents or openings. High voltage flows in the

product, and inserting an object can cause electric shock and/or

short internal parts. For the same reason, do not spill water or

liquid on the product.

16. Servicing - Do not attempt to service the product yourself.

Removing covers can expose you to high voltage and other

dangerous conditions. Request a qualified service person to

perform servicing.

17. Repair - If any of the following conditions occurs, unplug the power

cord from the AC outlet, and request a qualified service person to

perform repairs.

a. When the power cord or plug is damaged.

b. When a liquid was spilled on the product or when objects have

fallen into the product.

c. When the product has been exposed to rain or water.

d. When the product does not operate properly as described in

the operating instructions.

Do not touch the controls other than those described in the

operating instructions. Improper adjustment of controls not

described in the instructions can cause damage, which often

requires extensive adjustment work by a qualified technician.

e. When the product has been dropped or damaged.

f. When the product displays an abnormal condition. Any

noticeable abnormality in the product indicates that the

product needs servicing.

18. Replacement parts - In case the product needs replacement parts,

make sure that the service person uses replacement parts

specified by the manufacturer, or those with the same

characteristics and performance as the original parts. Use of

unauthorized parts can result in fire, electric shock and/or other

danger.

19. Safety checks - Upon completion of service or repair work, request

the service technician to perform safety checks to ensure that the

product is in proper operating condition.

20. Wall or ceiling mounting - When mounting the product on a wall or

ceiling, be sure to install the product according to the method

recommended by the manufacturer.

21. Heat sources - Keep the product away from heat sources such as

radiators, heaters, stoves and other heat- generating products

(including amplifiers).

22. Unplug the power cord from the AC outlet before installing the

speakers (for PDP-508XG only).

23. Never expose the screen of the plasma television to a strong

impact, for example, by hitting it. The screen may be broken,

resulting in fire or personal injury.

24. Do not expose the plasma television to direct sunlight for a long

period of time. The optical characteristics of the front protection

panel changes, resulting in discoloration or warp.

25. The plasma television weighs about 34.6 kg (76.3 lbs.) for the PDP-

508XG and about 29.6 kg (65.3 lbs.) for the PDP-428XG. Because it

has small depth and is unstable, unpack, carry, and install the

product with one more person at least and use the handles.

Safety precautions

Installation precautions

Observe the following precautions when installing with any items

such as the optional stand.

When using the optional stand, brackets, or equivalent

items

Ask your dealer to perform the installation.

Be sure to use the supplied bolts.

For details, see the instruction manual that comes with the

optional stand (or equivalent items).

When using other items

Consult your dealer.

The following six mounting holes can be used for the installation:

Side view

Caution

• Be sure to use four or more mounting holes symmetrical to the

vertical and horizontal median lines.

• Use M8 screws, which go 12 mm to 18 mm in depth from the

mounting surface of the plasma television. See the side view

above.

• Be careful not to block the ventilation opening at the rear of the

plasma television.

• Be sure to install the plasma television on a flat surface

because it contains glass.

• The screw holes other than the illustrations on the left are to be

used only for the specified products. Never use them for

mounting non-specified products.

• Do not mount or remove the plasma television to or from the

stand, with speakers attached (for PDP-508XG only).

Note

• It is strongly recommended to use the optional Pioneer

mounting products.

• Pioneer shall not be liable for any personal injury or product

damage that results from the use of mounting items other than

the optional Pioneer products.

Median

line

Median line

Mounting holes Mounting holes

Rear (PDP-508XG)

MONITOR

OUT

SUB

WOOFER

Median

line

Median line

Mounting holes Mounting holes

MONITOR

OUT

SUB

WOOFER

Rear (PDP-428XG)

Mounting surface

Plasma television

M8 screw

12 mm to 18 mm

Mounting bracket

(or equivalent)

Supplied accessories

English

Chapter 3

Supplied accessories

Check that all of the following accessories are supplied in the box.

*1 Either one of the power cords is supplied depending on the

country.

Power cord

(with a ferrite core attached) *

Power cord *

Remote control unit

AA size battery x 2

(for remote control unit)

Ferrite core

Cable tie (for ferrite core)

Speed clamp x 3

Bead band x 3

Cleaning cloth

Warranty card

Operating instructions

Part names

Chapter 4

Part names

Plasma television

(Front)

1  button (If the button is off, the power will not turn on even

when , 0 to 9 on the remote control unit or STANDBY/ON on

the plasma television is pressed.)

2 POWER ON indicator

3 STANDBY indicator

4 SLEEP indicator

5 Room Light Sensor

6 Remote control sensor

7STANDBY/ON button

8 INPUT button

9VOLUME +/– buttons

10 CHANNEL +/– buttons

11 USB port

12 PHONES output terminal

13 INPUT 6 terminal (S-VIDEO)

14 INPUT 6 terminal (VIDEO)

15 INPUT 6 terminals (AUDIO)

SLEEP

ON STANDBY

SLEEPON STANDBY

Viewed from the underside of the display

Viewed from the front of the display

Side PDP-508XG PDP-428XG Side

5 6

The terminals on side panels are common to the PDP-508XG and PDP-428XG.

Part names

English

Plasma television

(Rear)

1 AC IN terminal

2 ANT (antenna) input terminal

3 RS-232C terminal (used for factory setup)

4 CONTROL OUT terminal (supports SR+)

5 PC INPUT terminal (analog RGB)

6 INPUT 5 terminal (HDMI)

7 INPUT 4 terminal (HDMI)

8 INPUT 3 terminal (HDMI)

9 INPUT 1 terminals (AUDIO L, R)

10 INPUT 1 terminal (VIDEO)

11 INPUT 1 terminal (S-VIDEO)

12 INPUT 2 terminal (VIDEO)

13 INPUT 2 terminal (S-VIDEO)

14 INPUT 2 terminals (AUDIO L, R)

15 INPUT 3 terminal (S-VIDEO)

16 MONITOR OUT terminals (AUDIO L, R)

17 SUBWOOFER output terminal

18 MONITOR OUT terminal (VIDEO)

19 INPUT 3 terminal (VIDEO)

20 INPUT 2 terminals (COMPONENT VIDEO: Y, P

, P

)

21 PC INPUT terminal (AUDIO (STEREO))

22 INPUT 1 terminals (COMPONENT VIDEO: Y, P

, P

)

23 INPUT 3 terminals (AUDIO L, R)

24 SPEAKERS L, R terminals (PDP-508XG only)

MONITOR

OUT

SUB

WOOFER

MONITOR

OUT

SUB

WOOFER

MONITOR

OUT

SUB

WOOFER

MONITOR

OUT

SUB

WOOFER

MONITOR

OUT

SUB

WOOFER

MONITOR

OUT

SUB

WOOFER

PDP-508XG PDP-428XG

78 6 5 4 3 2 1

23 22 24

13 14 15 1716

23 22

13 14 15 1716

*For exact terminal positions, refer to the

terminal position sheet located near the

terminal compartment.

The terminals from 1 to 8 are the same as the PDP-508XG.

Part names

Remote control unit

This section describes the functions of the buttons available when

the TV mode has been selected by using the SELECT button. For the

buttons controlling other equipment, see Controlling other

equipment using the supplied remote control unit starting from

page 50.

1 : Turns on the power to the plasma television or places it into

the standby mode.

2 INPUT: Selects an input source (“INPUT 1”, “INPUT 2”, “INPUT

3”, “INPUT 4”, “INPUT 5”, “INPUT 6” or “PC”)

30 to 9: TV/External input mode: Selects a channel.

Teletext mode: Selects a page.

Turns the power on when the STANDBY indicator lights red.

4 CH RETURN: Returns to the previously selected channel.

5P+/P–: TV/External input mode: Selects a channel.

w/x: Teletext mode: Selects a page.

6 SELECT: Switches the selection among TV, STB, DVD/DVR, and

VCR, so that you can control other connected equipment,

using the supplied remote control unit.

7 TV, STB, DVD/DVR, VCR: These indicators show the current

selection and status when you control other connected

equipment, using the supplied remote control unit.

8 RETURN: Restores the previous menu screen.

9 ///: Selects a desired item on the setting screen.

ENTER: Executes a command.

10 HDMI CONTROL: Displays the HDMI Control menu.

11 Color (RED/GREEN/YELLOW/BLUE): Teletext mode: Selects a

page.

[: Jumps to the Teletext subtitle page.

13 k: Displays hidden characters.

14 h: Use to select a sound effect mode.

15 g: Sets the sound multiplex mode.

16 AV SELECTION: Selects audio and video settings. (AV source:

OPTIMUM, STANDARD, DYNAMIC, MOVIE, GAME, SPORT,

USER. PC source: STANDARD, USER.)

17 c: Press to select 2-screen, picture-in-picture or single screen

mode.

18 CH ENTER: Executes a channel selection by the number

buttons.

19 i +/i –: Sets the volume.

20 e: Mutes the sound.

21 HOME MENU: TV/External Input mode: Displays the HOME

MENU screen.

22 p : TV/External input mode: Displays the channel

information.

23 m: Selects the Teletext mode (all TV image, all TEXT image, TV/

TEXT image).

24 l: Teletext mode: Displays an Index page for the CEEFAX/

FLOF format.

25 f: TV/External input mode: Selects the screen size.

26 d: TV/External input mode: Freezes a frame from a moving

image. Press again to cancel the function.

: Teletext mode: Stops updating Teletext pages. Press again

to release the hold mode.

27 : Moves the position of the sub screen when in picture-in-

picture mode.

28 : Swaps the main and sub screens when in picture-in-

picture or 2-screen mode.

Note

• When using the remote control unit, point it at the plasma

television.

Preparation

English

Chapter 5

Preparation

Installing the plasma television

Location

• Avoid direct sunlight. Maintain adequate ventilation.

Caution

• If you do not leave sufficient space above the plasma television,

it will not receive enough ventilation and will not operate

properly.

• Pioneer will not be responsible for accident or damage caused

by inadequate installation or stabilization, erroneous

operation, remodeling or natural disasters.

Note

• Allow enough space around the upper and back parts when

installing to ensure adequate ventilation of the rear of the unit.

• Be sure to install the plasma television in a flat, stable location.

Using the optional Pioneer stand

For details on installation, refer to the instruction manual supplied

with the stand.

Using the optional Pioneer speakers (for PDP-508XG

only)

For details on installation, refer to the instruction manual supplied

with the speaker.

Moving the plasma television

When installing on a rack, etc., hold the plasma television as

shown on the right. Because the plasma television is heavy, be

sure to have someone help you when moving it.

(For PDP-508XG)

Under speaker

Side speaker

(For PDP-428XG)

Note

• Do not use the speaker to support the weight of the plasma

television.

• When the plasma television has under-mounted speakers,

always remove the speakers before moving the plasma

television. Do not hold the plasma television by the speaker

mounting fittings.

Over 50 cm

Over

10 cm

Preparation

Preventing the plasma television from

falling over

After installing the stand, be sure to take special care to ensure

that the plasma television will not fall over and is stabilized to both

the wall and rack.

Stabilizing on a table or rack

Stabilize the plasma television as shown in the diagram using the

plastic bands and screws supplied with the optional stand.

Note

• To stabilize the plasma television on a table or rack, use screws

that have a nominal diameter of 4 mm and that are at least 20

mm long.

Caution

• A table or rack with adequate strength should always be used

to support the plasma television. Failure to do so could result

in personal injury and physical damage.

• When installing the plasma television, please take the

necessary safety measures to prevent it from falling or

overturning in case of emergencies, such as earthquakes, or of

accidents.

• If you do not take these precautions, the plasma television

could fall down and cause injury.

• The screws, hooks, cords and other fittings that you use to

secure the plasma television to prevent it from overturning will

vary according to the composition and thickness of the surface

to which it will be attached.

• Select the appropriate screws, hooks, cords, and other fittings

after first inspecting the surface carefully to determine its

thickness and composition and after consulting a professional

installer if necessary.

Using a wall for stabilization

1 Attach falling prevention bolts (hooks) to the plasma

television.

2 Use strong cords to stabilize it appropriately and firmly to

a wall, pillar, or other sturdy element.

Perform this work in the same way on the left and right sides.

Use hooks, cords and fittings that are available on the market.

Recommended hook: Nominal diameter 8 mm Length 12 mm to

18 mm.

Basic connections

Connecting the antenna

To enjoy a clearer picture, use an outdoor antenna. The following is

a brief explanation of the types of connections that are used for a

coaxial cable.

• Connect the 75-ohm coaxial cable (commercially available) to

the ANT IN (antenna input) terminal.

NITOR

OUT

SUB

WOOFE

20 mm min.

4 mm

8 mm to 15 mm

Screw

(M4 x 10 mm)

Wood screw

(commercially available,

4 mm x 20 mm min.)

Wood screw

Screw

Drill a hole in the

middle at the rear

of the tabletop

panel before using

a wood screw.

Perform this work

the same way on

the left and right

sides.

MONITOR

OUT

OOFE

12 mm to 18 mm

1. Hook

2. Cord

Fitting

MONITOR

OUT

SUB

WOOFER

Standard DIN45325 plug (IEC169-2)

75-ohm coaxial cable (round cable)

(commercially available)

(Rear view)

Preparation

English

Antenna cable (commercially available)

If your outdoor antenna uses a 75-ohm coaxial cable with a

standard DIN45325 plug (IEC169-2), plug it into the antenna

terminal at the rear of the plasma television.

Note

• If the antenna is not connected correctly, the quality of

reception may be impaired. If images are not displaying

correctly, check whether the antenna connection is correct or

not.

Routing cables

Use the speed clamps as necessary to route the connecting

cables. The diagrams below show the location of the holes on the

rear of the display.

Attaching and removing speed clamps

Insert [1] into an appropriate hole on the rear of the plasma

television and snap [2] into the back of [1] to lock the clamp.

• Speed clamps are designed to be difficult to undo once in

place. Please attach them carefully.

• Use pliers to twist the clamp 90º, pulling outward. The clamp

may deteriorate over time and become damaged if removed.

• Be careful not to subject any connecting cables to strain.

Note

• Use the speed clamps as necessary.

Tidying the speaker cables (PDP-508XG only)

Use the supplied bead bands as necessary to tidy the speaker cables.

Attaching the ferrite core

(when a ferrite core is not attached)

To help prevent noise, attach the supplied ferrite core to the

connector end of the power cord as shown. Use the supplied cable

tie to prevent the ferrite core from slipping on the cable.

Connecting the power cord

Note

• Disconnect the power cord from the power outlet when the

plasma television is not going to be used for a long period of time.

• After all other components are connected, connect the power

plug to the AC outlet.

MONITOR

OUT

SUB

WOOFER

PDP-508XG (Rear view)

MONITOR

OUT

SUB

WOOFER

PDP-428XG (Rear view)

MONITOR

OUT

SUB

WOOFER

PDP-428XG (Rear view)

MONITOR

OUT

SUB

WOOFER

Speaker cable

Bead band

Rear view

Ferrite core

Cable tie

AC power cord

To power outlet

As close as possible

MONITOR

OUT

SUB

WOOFER

To power outlet

Power cord

Rear view

Ferrite core

Partially eliminates noise

caused by the power source.

Preparation

Preparing the remote control unit

Inserting batteries

1 Open the battery cover.

2 Load the supplied two AA size batteries while inserting

their respective negative polarity (–) ends first.

Place batteries with their terminals corresponding to the (+) and

(–) indicators in the battery compartment.

3 Close the battery cover.

Caution

Improper use of batteries can result in chemical leakage or an

explosion. Be sure to follow the instructions below.

• When you replace the batteries, use manganese or alkaline

ones.

• Place the batteries with their terminals corresponding to the

(+) and (–) indicators.

• Do not mix batteries of different types. Different types of

batteries have different characteristics.

• Do not mix old and new batteries. Mixing old and new batteries

can shorten the life of new batteries or cause chemical leakage

in old batteries.

• Remove batteries as soon as they have worn out. Chemicals

that leak from batteries can cause a rash. If you find any

chemical leakage, wipe thoroughly with a cloth.

• The batteries supplied with this product may have a shorter life

expectancy due to storage conditions.

• If you will not use the remote control unit for an extended

period of time, remove the batteries from it.

• WHEN DISPOSING OF USED BATTERIES, PLEASE COMPLY

WITH GOVERNMENTAL REGULATIONS OR

ENVIRONMENTAL PUBLIC INSTITUTION’S RULES THAT

APPLY IN YOUR COUNTRY/AREA.

Operating range of the remote control unit

Operate the remote control unit while pointing it toward the remote

control sensor located at the bottom right of the front panel of the

plasma television. The distance from the remote control sensor

must be within 7 m and the angle relative to the sensor must be

within 30 degrees in the right, left, upward, or downward direction.

Note

• For the remote control sensor located on the PDP-428XG, see

Part names on page 12.

Caution

• Do not expose the remote control unit to shock. In addition, do

not expose the remote control unit to liquids, and do not place

in an area with high humidity.

• Do not install or place the remote control unit under direct

sunlight. The heat may cause deformation of the unit.

• The remote control unit may not work properly if the remote

control sensor of the plasma television is under direct sunlight

or strong lighting. In such case, change the angle of the

lighting or plasma television, or operate the remote control unit

closer to the remote control sensor.

• When any obstacle exists between the remote control unit and

the remote control sensor, the remote control unit may not

function.

• As the batteries become empty, the remote control unit can

function within a shorter distance from the remote control

sensor. Replace the batteries with new ones early enough.

• The plasma television emits very weak infrared rays from its

screen. If you place such equipment operated through infrared

remote control as a VCR nearby, that equipment may not

receive commands from its remote control unit properly or

entirely. If this is the case, place that equipment at a location

far enough from the plasma television.

• Depending on the installation environment, infrared rays from

the plasma television may not allow this system to properly

receive commands from the remote control unit or may

shorten allowable distances between the remote control unit

and the remote control sensor. The strength of infrared rays

emitted from the screen differs, depending on images

displayed on the screen.

30º

Remote

control

sensor

7 m

Watching TV

English

Chapter 6

Watching TV

Important

• Before watching broadcast channels, the built-in TV tuner

must be set up. See Setting up TV channels automatically on

page 25 for how to do this.

Turning the power on

• Press  on the plasma television when the POWER ON and

STANDBY indicators are off.

•The system is on.

• The POWER ON indicator lights up blue.

• Press  or 0 to 9 on the remote control unit or STANDBY/

ON on the plasma television if the STANDBY indicator lights

red.

• The POWER ON indicator lights up blue.

• If you press 0 on the remote control unit, images from “INPUT 1”

will be displayed.

•If you press 1 to 9, TV images will be displayed.

Placing the system into standby

Press  on the remote control unit or STANDBY/ON on the

plasma television.

• The STANDBY indicator lights up red.

• The system enters the standby mode and the image on the

screen disappears.

Note

• When  on the plasma television is off, you cannot turn the

power on by pressing  or 0 to 9 on the remote control unit or

STANDBY/ON on the plasma television.

• If you are not going to use the plasma television for a long

period of time, be sure to remove the power cord from the

power outlet.

Plasma television status indicators

The table below shows the operational status of the plasma

television. You can check the current status of the system with the

indicators on the plasma television.

For other than the above, see Troubleshooting on page 63.

ON STANDBY

 button

POWER ON indicator

STANDBY indicator

PDP-508XG

Indicator status System status

POWER ON STANDBY

The power cord of the plasma television has been

disconnected. Or, the power cord of the plasma

television has been connected but the

 button

of the plasma television is off.

Power to the system is on.

The system is in the standby mode.

 button

ON STANDBY

POWER ON indicator

STANDBY indicator

PDP-428XG

Watching TV

Note

• You can select “Auto”, “High”, “Mid” or “Low” for the brightness

of the POWER ON indicator. When “Auto” is selected, the

brightness of the indicator changes to “High”, “Mid” or “Low”

to match the brightness level of the viewing area. For details,

see Blue LED Dimmer on page 39.

Changing channels

Use the remote control or the control panel on the right-hand side

of the plasma television to change channels.

• Before operating with the remote control unit, make sure to

select the TV mode using its SELECT button. See Controlling

other equipment using the supplied remote control unit on

page 50.

Using P+ / P– on the remote control unit

• Press P+ to increase the channel number.

• Press P– to decrease the channel number.

Note

• CHANNEL +/– on the plasma television operates the same as

P+/P–.

• Press CH RETURN to switch back to the previous channel.

Press again to return to the current channel.

• P+/P– cannot pick up channels that are set to skip. For Channel

Skip, see steps 13 and 14 under Setting up TV channels

manually on page 25.

Using 0 to 9 on the remote control unit

• Select channels directly by pressing buttons 0 to 9.

For example:

Press 2 to select channel 2 (one-digit channel).

Press 1 then 2 to select channel 12 (two-digit channel).

Press 1, 2 then 3 to select channel 123 (three-digit channel).

When viewing Teletext information:

• View a page directly which is three-digit page number from 100

to 899 by pressing buttons 0 to 9. See also Operating the

Teletext basics on page 61.

Note

•Press CH RETURN to switch back to the previous channel.

Press again to return to the current channel.

• After entering a channel number you can press

CH ENTER to tune in the channel more quickly.

• In standby, when you press 0, the power turns on and images

come from the “INPUT 1” source. Or, when you press any

button from 1 to 9, TV images display.

Changing the volume and sound

Use the remote control or the control panel on the right-hand side

of the plasma television to adjust the volume.

Using

+ /

– on the remote control unit

•Press i + to increase the volume.

•Press i – to decrease the volume.

• VOLUME +/– on the plasma television operates the same as

i + /i –.

Using

on the remote control unit

•Press e to mute the sound.

e appears on the screen.

•Press e again or i + to restore the sound.

AAA

STEREO

STANDARD

FULL

Channel display

Volume adjustment

Muting

Watching TV

English

Switching the broadcast audio channel

Depending on the broadcast, you can switch the audio channel.

• Press - to change the audio channel.

The table below shows the available audio channels by broadcast

audio type.

Note

• In each of the sound multiplex mode selected using the -

button, the display changes depending on broadcasting

signals being received.

• Once the MONO mode is selected, the plasma television sound

remains mono even if the system receives a stereo broadcast.

You must switch the mode back to  or  mode if you want to

hear stereo sound again.

• Selecting a sound multiplex mode while the input source is

“INPUT 1” to “INPUT 6” or “PC” does not change the type of

sound. In this case, sound is determined by the video source.

• While watching a TV channel with any High Deviation setting

(page 26), you cannot change the sound multiplex mode.

Using the multiscreen functions

• Before operating with the remote control unit, make sure to

select the TV mode using its SELECT button. See Controlling

other equipment using the supplied remote control unit on

page 50.

Splitting the screen

Use the following procedure to select the 2-screen or picture-in-

picture mode.

Note

• Displaying a split screen for a long period of time, or for shorter

periods of time everyday, may result in image retention.

 mode  mode MONO mode

I II MONO

AAA

NICAM STEREO

AAA

NICAM STEREO

AAA

MONO

BBB

NICAM 

BBB

NICAM 

BBB

MONO

CCC

NICAM MONO

CCC

NICAM MONO

CCC

MONO

NICAM BroadcastsA2 BroadcastsBTSC Broadcasts

Stereo

Bilingual

Monaural

DDD

STEREO

DDD

STEREO

DDD

MONO

EEE

DUAL 

EEE

DUAL 

EEE

MONO

FFF

MONO

FFF

MONO

FFF

MONO

Stereo

Bilingual

Monaural

GGG

STEREO

GGG

STEREO

GGG

MONO

HHH

MONO(SAP)

HHH

SAP(MAIN)

HHH

MONO

JJJ

STEREO(SAP)

JJJ

SAP(STEREO)

JJJ

MONO

Stereo

MAIN+SAP

Stereo+SAP

KKK

MONO

KKK

MAIN

KKK

MONO

Monaural

Setting

MONO

2-screen

Picture-in-picture

Main screen Sub screen

Watching TV

1 Press c to select the display mode.

Each time you press c, the display mode is switched between

2-screen, picture-in-picture, and single-screen modes.

• In 2-screen or picture-in-picture mode, press to switch the

position of the two screens shown.

• The left screen (in the 2-screen mode) or the larger screen (in

the picture-in-picture mode) is the active screen, indicated by a

“z” icon. You can use any of the normal functions to change

the picture and sound.

• In picture-in-picture mode, press to move the position of

the small screen anti-clockwise.

2 To select the desired input source, press the appropriate

input source button.

• If watching TV programs, press P+/P– to change the channel.

Note

• The multiscreen function cannot display images from the same

input source at the same time. If you make such an attempt, a

warning message appears.

• The multiscreen function cannot display images from

combinations of two external input sources (“INPUT 1” to

“INPUT 6”, “PC”). It can display images from the following

combinations of inputs sources: built-in TV tuner and one

external source (“INPUT 1” to “INPUT 6”, “PC”).

• When you press HOME MENU, the single-screen mode is

restored and the corresponding menu is displayed.

• When in the 2-screen mode, images displayed on the right

screen may look less fine, depending on images.

• With headphones connected, you can listen to audio coming

from the sub screen when in the 2-screen or picture-in-picture

mode. For more information, see Listening to audio from the

sub screen using headphones on page 33.

Freezing images

Use the following procedure to capture and freeze one frame from

a moving image that you are watching.

• Before operating with the remote control unit, make sure to

select the TV mode using its SELECT button. See Controlling

other equipment using the supplied remote control unit on

page 50.

Important

• Displaying a static image for a long period of time, or for

shorter periods of time everyday, may result in image retention.

•Press d.

A still image appears on the right screen while a moving image is

shown on the left screen.

•Press d again to cancel the function.

Note

• You cannot freeze the picture when using the 2-screen or

picture-in-picture mode.

• When this function is not available, a warning message

appears.

Normal image Still image

The HOME MENU

English

Chapter 7

The HOME MENU

HOME MENU overview

For AV source

For PC source

HOME MENU Item Page

Picture AV Selection 28

Contrast 28

Brightness 28

Color 28

Tint 28

Sharpness 28

Pro Adjust 29

Reset 28

Sound Treble 33

Bass 33

Balance 33

Reset 33

Sound Effect 33

Headphone Output 33

Sub Volume 33

Power Control Energy Save 34

No Signal off 34

No Operation off 34

Sleep Timer – 40

Option Position 36

Auto Size 38

Side Mask 39

HDMI Input 45

HDMI Control Setting 59

Blue LED Dimmer 39

Orbiter 39

Video Pattern 40

Drive Mode 36

Color System 37

Monitor Out 44

Game Control Pref 37

Room Light Sensor 39

Setup Auto Installation 25

Analog TV Setup 25

Password 40

Language 27

Home Gallery –49

HDMI Control –56

HOME MENU Item Page

Picture AV Selection 28

Contrast 28

Brightness 28

Red 28

Green 28

Blue 28

Reset 28

Sound Same as AV source menu 33

Power Control Energy Save 34

Power Management 35

Sleep Timer – 40

Option Auto Setup 36

Manual Setup 37

HDMI Input 45

HDMI Control Setting 59

Home Gallery – 49

HDMI Control – 56

HOME MENU Item Page

The HOME MENU

Using the HOME MENU

The following describes the typical procedure for setting up the

menus. For the actual procedures, see the appropriate pages that

describe individual functions.

1 Press HOME MENU.

2 Press / to select a menu item, and then press ENTER.

3 Repeat step 2 until you access the desired submenu item.

The number of menu layers differs depending on the menu items.

4 Press / to select an option (or parameter), and then

press ENTER.

For some menu items, press / instead of /.

5 Press HOME MENU to exit the menu.

Note

• You can return to the upper menu levels by pressing RETURN.

• Before operating with the remote control unit, make sure to

select the TV mode using its SELECT button. See Controlling

other equipment using the supplied remote control unit on

page 50.

Setting up

English

Chapter 8

Setting up

Setting up TV channels automatically

This section describes how to automatically search for and set up

TV channels.

Using Auto Installation

When the plasma television is switched on for the first time after

purchase, the initial auto installation is initiated. You can set

language, region and channels in successive operations.

1 Select “Language“ (/).

2 Select a language (/).

You can select from among five languages; English, Spanish,

Portuguese, traditional Chinese and simplified Chinese.

3 Select “Region“ (/).

4 Select your region (/).

Select the country or region in which you live. If it is not listed,

select “Other regions”.

5 Select “Channel Allocation“ (/).

6 Select “General”, “Air (US Type)“ or “Cable (US Type)” (/

).

The table on page 65 (Standard channel allocation selections for

countries and regions) shows which option you should usually

select in your country or region.

7 Select “Start“ (/ then ENTER).

Auto Installation automatically starts.

• To quit Auto Installation in progress, press RETURN.

Note

• You can start Auto Installation from the HOME MENU after

moving to another country, for example. Perform the following

steps before starting Auto Installation: Press HOME MENU,

select “Setup” (/ then ENTER), then “Auto Installation” (/

 then ENTER). The password entry screen appears. Enter

your four-digit password using buttons 0 to 9. For the

password, see Using a password on page 40.

• If no channels are found, check the antenna connections, and

then retry Auto Installation.

Setting up TV channels manually

Use the Manual Adjust function to set up TV channels manually.

Steps 5 to 14 differ depending on your selection for Channel

Allocation.

1 Press HOME MENU.

2 Select “Setup“ (/ then ENTER).

3 Select “Analog TV Setup“ (/ then ENTER).

The password entry screen appears. Enter your four-digit password

using buttons 0 to 9. For the password, see Using a password on

page 40.

4 Select “Manual Adjust“ (/ then ENTER).

5 Select “Program Entry“ (/).

6 Select a program number (/).

• With “General” selected, you can select 1 through 99.

• With “Air (US Type)” selected, you can select 2 through 69.

• With “Cable (US Type)” selected, you can select 1 through 125.

7 Select “Search“ (/).

8 Enter a frequency using buttons 0 to 9, then ENTER.

You can also press / to enter a frequency.

• With “Air (US Type)” or “Cable (US Type)” selected, you cannot

change the display frequency.

9 Select “System“ (/).

10 Select a sound system (/).

You can select from among “B/G”, “D/K”, “I” and “M/N”.

• With “Air (US Type)” or “Cable (US Type)” selected, you cannot

change the factory default (“M/N”).

Item Description

General Scans to locate your regional broadcasting

frequencies. The earlier the frequencies identified, the

smaller the channel numbers used.

Air (US Type) Searches for the same broadcasting frequencies as for

receiving over air in the U.S. This selection is effective

when the system is receiving over air.

Cable (US Type) Searches for the same broadcasting frequencies as for

watching cable TV in the U.S. This selection is effective

when the system is receiving from a cable TV company.

Auto Installation

Channel Allocation

Installation

Language

English

Start

General

Region

Australia

Manual Adjust

System

Program Entry

Color System

Store

Tun er NR

Child Lock

High Deviation

44.25MHz

B/G

Auto

View

Yes

Off

Setting up

11 Select “Color System“ (/).

12 Select a color system (/).

You can select from “Auto”, “PAL”, “NTSC”, “SECAM”, “PAL-M”,

“PAL-N”, and “4.43NTSC”.

• With “Air (US Type)” or “Cable (US Type)” selected, you cannot

change the factory default (“Auto”).

13 Select “Store“ (/).

14 Select “Yes“ (/).

• With “Air (US Type)” or “Cable (US Type)” selected, press /

to select “ADD/DEL”, then press / to select “ADD”.

• With “Yes” selected, you can select the channel using P+/P–.

With “No” selected, you cannot select the channel using

P+/P–.

15 Press HOME MENU to exit the menu.

• Alternatively, to set up for another channel, repeat steps 5 to 14.

Note

• Manual Adjust also allows you to make selections for “Tuner

NR”, “Child Lock”, and “High Deviation”. See Reducing video

noise, Setting Child Lock, and Suppressing audio distortion

respectively.

• This plasma television is equipped with the auto frequency

tuning function that automatically adjusts tuning frequencies

according to received signals. For this reason, the Manual

Adjust menu may show slightly different frequencies from your

entry when you access the menu next time. You cannot

deactivate the Auto Frequency Tuning function.

Reducing video noise

For the individual channels, you can specify whether the plasma

television should reduce video noise depending on the levels of

broadcasting signals.

1 Press HOME MENU.

2 Select “Setup” (/ then ENTER).

3 Select “Analog TV Setup” (/ then ENTER).

The password entry screen appears. Enter your four-digit password

using buttons 0 to 9. For the password, see Using a password on

page 40.

4 Select “Manual Adjust” (/ then ENTER).

5 Select “Program Entry” (/).

6 Select a program number (/).

• With “General” selected, you can select 1 through 99.

• With “Air (US Type)” selected, you can select 2 through 69.

• With “Cable (US Type)” selected, you can select 1 through 125.

7 Select “Tuner NR“ (/).

8Select “On“ (/).

9 Press HOME MENU to exit the menu.

Note

• This function may not achieve a satisfactory result, depending

on the conditions of broadcasting signals.

• The factory default is “On”.

Setting Child Lock

Child Lock inhibits selected TV channels from being tuned and

watched.

1 Repeat steps 1 to 6 provided for Reducing video noise.

After selecting a program number (using Program Entry), perform

the following steps:

2 Select “Child Lock“ (/).

3 Select “Block“ (/).

• The selection is switched between “View” (factory default) and

“Block”.

4 Press HOME MENU to exit the menu.

Suppressing audio distortion

You can suppress audio distortion that may be induced when too

strong audio signals are received in the selected channel.

Note

• High Deviation is selectable only when you have selected “D/K”

for “System” under Setting up TV channels manually on

page 25.

1 Repeat steps 1 to 6 provided for Reducing video noise.

After selecting a program number, perform the following steps:

2 Select “High Deviation“ (/).

3 Select “High”, “Mid” or “Low” (/).

With “Air (US Type)” or “Cable (US Type)” selected, you cannot

change the factory default (“Off”).

4 Press HOME MENU to exit the menu.

Note

• While watching a TV channel with any High Deviation setting,

you cannot change the sound multiplex mode.

Item Description

Off Deactivates the function

High Suppresses audio distortion slightly; however, the

audio volume is slightly lowered than when Off is

selected

Mid Suppresses audio distortion moderately

Low Suppresses audio distortion further; however, the

audio volume is further lowered

Setting up

English

Labeling TV channels

You can name TV channels that you have set up, using up to five

characters. This may help you easily identify the channels during

selections.

1 Press HOME MENU.

2 Select “Setup“ (/ then ENTER).

3 Select “Analog TV Setup“ (/ then ENTER).

Enter your four-digit password using buttons 0 to 9 when

prompted.

4 Select “Label“ (/ then ENTER).

5 Select “Program Entry“ (/).

6 Select a program number (/).

• With “General” selected, you can select 1 through 99.

• With “Air (US Type)” selected, you can select 2 through 69.

• With “Cable (US Type)” selected, you can select 1 through 125.

7 Select “Label“ (/ then ENTER).

The name entry screen appears.

8 Select the first character (///, then ENTER).

• The cursor moves to the second character.

9 Repeat step 8 to enter up to five characters.

• To correct entered characters, select [] or [] on the

screen, and then press ENTER. The cursor moves to the

preceding or subsequent character.

• To delete the current character, select [Delete] on the screen,

and then press ENTER.

• To put a space for the current character, select [Space] on the

screen, and then press ENTER.

10 To complete the name entry, press / or / to select

[OK] on the screen, and then press ENTER.

11 Press HOME MENU to exit the menu.

Sorting preset TV channels

After performing a “General” channel search, you can use the

following procedure to change the sequence of the preset TV

programs. (Sorting preset TV channels is not possible if you used

“Air (US Type)” or “Cable (US Type)“ for your channel search.)

1 Press HOME MENU.

2 Select “Setup“ (/ then ENTER).

3 Select “Analog TV Setup“ (/ then ENTER).

Enter your four-digit password using buttons 0 to 9 when

prompted.

4 Select “Sort“ (/ then ENTER).

The sort screen appears.

5 Select a channel to be shifted (/// then ENTER).

6 Select a new location (/// then ENTER).

Sorting is executed.

7 Press HOME MENU to exit the menu.

Note

• To change a page on the Sort screen in step 6, select / on

the screen with / to select a page, and then press ENTER.

Language setting

You can select the language to be used for on-screen display such

as menus and instructions, from among five languages; English,

Spanish, Portuguese, traditional Chinese and simplified Chinese.

For the language to be used in the Teletext mode, you can select

from among West Europe, East Europe, Greece/Turkey, Russia,

and Arabia.

1 Press HOME MENU.

2 Select “Setup“ (/ then ENTER).

3 Select “Language“ (/ then ENTER).

4 Select “Menu“ (/).

5 Select a language (/).

6 Select “Teletext“ (/).

7 Select a language (/).

8 Press HOME MENU to exit the menu.

Label

Program Entry

1234567890

Delete

Space

BCDEFGH I J

KLMNOPQRST

UVWXYZ, . : ;

&' ( )+- * /_

Sort 1/4

AAAAA01

BBBBB02

CCCCC03

DDDDD04

EEEEE05

FFFFF06

GGGGG07

HHHHH08

IIIII09

RRRRR18

JJJJJ

KKKKK

LLLLL

MMMMM

NNNNN

OOOOO

PPPPP

SSSSS

TTTTT

UUUUU

VVVVV

WWWWW

XXXXX

YYYYY

QQQQQ

Language

Teletext

West Europe

English

Setting up

AV Selection

Select from the seven viewing options, depending on the current

environment (e.g., room brightness), the type of the current TV

program, or the type of images input from external equipment.

1 Press HOME MENU.

2 Select “Picture“ (/ then ENTER).

3 Select “AV Selection“ (/ then ENTER).

4 Select the desired option (/ then ENTER).

For AV source

For PC source

5 Press HOME MENU to exit the menu.

Note

• You can also press AV SELECTION on the remote control to

change the viewing option.

• If you have selected “DYNAMIC”, you cannot select “Contrast”,

“Brightness”, “Color”, “Tint”, “Sharpness”, “Pro Adjust”, and

“Reset”; these menu items are dimmed.

• If you have selected “OPTIMUM”, you cannot select “Pro

Adjust”; menu items in “Pro Adjust” are dimmed.

• As “OPTIMUM” automatically optimizes image quality, the

process in which image settings such as brightness and tint

gradually change may be seen on the screen. This is not a

malfunction.

• When “OPTIMUM” is selected, images are reproduced based

on the information collected at the Room Light Sensor as well,

regardless of its setting (“On” or “Off”) for the “Option” menu.

Basic picture adjustments

Adjust the picture to your preference for the chosen AV Selection

option (except DYNAMIC).

1 Press HOME MENU.

2 Select “Picture“ (/ then ENTER).

3 Select an item to be adjusted (/ then ENTER).

For a PC source or when the Home Gallery function is on, the

following screen appears:

4 Select the desired level (/).

When an adjustment screen is in display, you can also change the

item to be adjusted, by pressing /.

5 Press HOME MENU to exit the menu.

Item Description

OPTIMUM Automatically adjusts the brightness of the image to

the optimum level in accordance with the brightness

level of the viewing area.