Size:
8.03 Mb
Download

TECHNICAL MANUAL (Ver. 1.1)

FOR PIONEER PLASMA DISPLAY MONITOR WHEN USED WITH VIDEO CARDS (EXPANSION SOLUTIONS CARDS)

PLASMA DISPLAY MONITOR: PDP-607CMX

VIDEO CARD: PDA-5003 / PDA-5004

TABLE TOP STAND: PDK-TS26

WALL MOUNT UNIT: PDK-WM03

SPEAKER SYSTEM: PDP-S55-LR

This manual provides precautions and information for installation, preparation, and handling of the Plasma Display and its dedicated mounting hardware.

Before installation and preparatory work, choose a safe and appropriate site after thorough consideration of construction, materials used, strength, and surroundings. If adequate safeguards are not in place, immediately halt the installation process and discontinue marketing activities.

ABOUT MOUNTING/INSTALLATION

This product is sold under the assumption that installation will be performed by experienced, qualified experts. Refer all mounting and installation work to qualified personnel or consult the nearest PIONEER dealer for assistance.

We accept no responsibility for accident or loss resulting from failure to select an appropriate installation site, situations occurring during assembly, installation, mounting, operation resulting from modifications made to this product, or from natural disasters.

PRECAUTIONS:

We accept no responsibility for losses resulting from the use of parts other than those supplied by Pioneer or those authorized by Pioneer.

We guarantee the performance of our products only when they are assembled and adjusted as described in this manual.

The specifications and external designs shown in this manual are subject to change without notice.

To use this product safely

When using this product attached to a ceiling or wall or piled up, there is a danger that, according to its weight or attachment method, it may fall down or fall over.

In order to use this product safely, be sure to have a professional installer or the retail agent perform the installation work. Verify that it is appropriately attached and take adequate safety measures.

Attention professional installer

Install this product according to the instructions in the owner’s manual or installation manual.

To ensure safety when this product is installed on a ceiling, wall or stacked be sure to take measures to prevent any danger of the panel(s) falling down or falling over.

Choose an installation or attachment location that has sufficient strength to fully withstand its weight.

When installing it on the floor, select an adequately stable, flat, and level place.

To prevent damage to the power or connection cords, take great care not to place any equipment on them or pinch them between any equipment.

Absolutely do not alter the product or any of its attachment hardware.

Table of Contents

INTRODUCTION .....................................................................

4

FEATURES ..............................................................................

 

5

SPECIFICATIONS

 

2.1

Specifications ...............................................................

6

2.2

External Dimensions ....................................................

8

2.3

Controls and Connectors ...........................................

10

2.4

Pin layout ....................................................................

13

2.5

Remote Control Unit ..................................................

14

INSTALLATION SITE REQUIREMENTS

 

3.1

Installation Site Requirements ..................................

15

3.2

Installation Conditions ...............................................

17

 

3.2.1

Heat dissipation ................................................

17

 

3.2.2

Calculating heat quantity ...................................

18

 

3.2.3

Product mounting holes ....................................

18

 

3.2.4

Mounting surface warping ................................

20

3.3

Installation Procedures ..............................................

21

 

3.3.1

Transportation precautions ...............................

21

 

3.3.2

Unpacking .........................................................

21

 

3.3.3

Re-packing ........................................................

22

 

3.3.4

Wiring ................................................................

22

3.4

Special Installation .....................................................

24

 

3.4.1

Mounting to fittings ..........................................

24

 

3.4.2

Hanging on the wall ..........................................

26

 

3.4.3

Embedding in the wall ......................................

28

 

3.4.4

When the display is put in a box .......................

31

 

3.4.5

Ceiling suspension (with wires) ........................

32

 

3.4.6

Hanging on the wall lengthwise ........................

34

 

3.4.7

Place product upright and flush into wall

 

 

 

(embedding in the wall) .....................................

36

 

3.4.8

Installed facing upward .....................................

40

 

3.4.9

Horizontal connections ......................................

42

 

3.4.10 Multiple .............................................................

43

HOW TO USE THE STANDARD MOUNTING COMPONENTS

4.1

Standard Mounting Components Features and

 

 

Characteristics ............................................................

44

4.2

Handling the Standard Mounting Components ......

45

 

4.2.1

Handling precautions ........................................

45

 

4.2.2

Precautions for installation contractors .............

45

4.3

Video

Card: PDA-5003/PDA-5004 ..............................

46

 

4.3.1

Specifications ....................................................

46

 

4.3.2

External Dimensions .........................................

48

 

4.3.3

Installing procedures .........................................

50

 

4.3.4

Input connectors on the Plasma Display with

 

 

 

video card ..........................................................

52

 

4.3.5

Connection to INPUT1 and INPUT5 ..................

52

 

4.3.6

Connection to INPUT1 or INPUT5 .....................

53

 

4.3.7

Connection to INPUT2 ......................................

58

 

4.3.8

Connection to INPUT3 ......................................

58

 

4.3.9

Connection to INPUT4 ......................................

58

 

4.3.10 About DTV set top box connection ...................

59

 

4.3.11 Audio connections ............................................

60

4.4

Table Top Stand: PDK-TS26 ......................................

64

 

4.4.1

Specifications ....................................................

64

 

4.4.2

Installation coordinates for screws used to

 

 

 

attach the stand to a surface ............................

65

 

4.4.3

External Dimensions .........................................

65

 

4.4.4

Stand assembling ..............................................

66

 

4.4.5

Attaching the Stand to the Plasma Display .......

67

4.5

Wall Mount Unit: PDK-WM03 ...................................

68

 

4.5.1

Specifications ....................................................

68

 

4.5.2

External Dimensions .........................................

69

 

4.5.3

Hardware assembly and Plasma Display

 

 

 

attachment ........................................................

70

4.6

Speaker System: PDP-S55-LR ...................................

72

 

4.6.1

Specifications ....................................................

72

 

4.6.2

External Dimensions .........................................

73

 

4.6.3

Installation on the Plasma Display ....................

74

BEFORE BEGINNING ADJUSTMENT/SETTING

5.1 Before Beginning Adjustment ..................................

78

5.1.1

Operation Mode ................................................

78

5.1.2 Combined Use of the Remote Control,

 

 

Main-control Panel, and RS-232C Commands ...

79

5.1.3 List of Input Correspondence Signals ...............

80

5.1.4 List of Adjustable and Settable Items ...............

90

5.1.5

Last Memory .....................................................

98

5.1.6

Aging .................................................................

98

5.2 Normal Operation Mode ...........................................

99

5.2.1 About normal operation mode ............................

99

5.3 Menu Mode ..............................................................

101

5.3.1

About menu mode ..........................................

101

5.3.2 Concerning the display of the OSD of

 

 

each item ........................................................

101

5.3.3 Example of a Menu Mode Operation ..............

102

5.3.4 Adjustment and setting in the Menu Mode ....

103

 

1)

Power Management Setting ....................

103

 

2)

Signal Format Setting ...............................

104

 

3)

Menu Language Display Setting ...............

105

 

4)

Energy Saving Setting ..............................

106

 

5)

Timer Setting ............................................

108

 

6)

Program/Repeat Timer Setting .................

108

 

7)

Orbiter Setting ..........................................

109

 

8)

Soft Focus Setting ....................................

110

 

9)

Auto Set Up Mode Setting .......................

111

 

10)

Screen Position, Clock Frequency and

 

 

 

Clock Phase Adjustment ..........................

112

 

11)

Auto Function Mode Setting ....................

114

 

12)

PIP DETECT Setting .................................

115

 

13)

SPLIT FREEZE Setting ..............................

116

5.3.5Concerning the display of the OSD of each item (Applicable only when a PDA-5003/PDA-5004

is installed.) .....................................................

117

5.3.6 Example of a Menu Mode Operation ..............

117

(Applicable only when a PDA-5003/PDA-5004

 

is installed.) .....................................................

117

5.3.7Adjustment and setting in the Menu Mode (Applicable only when a PDA-5003/PDA-5004

is installed.) .....................................................

118

1)

Color Temperature Setting .......................

118

2)

Power Management and Auto Power

 

 

OFF Setting ..............................................

119

3)

DNR (digital noise reduction) Setting ........

120

4)

MPEG NR Setting .....................................

121

5)

CTI Setting ................................................

122

6)

PURECINEMA Setting ..............................

123

7)

Color Decoding Setting .............................

125

8)

Color System Setting ................................

126

9)

Signal Format Setting ...............................

127

10)

DVI Setting ...............................................

129

11)

Menu Language Display Setting ...............

130

12)

Energy Saving Setting ..............................

131

13)

Timer Setting ............................................

133

14) Program/Repeat Timer Setting .................

133

15)

Orbiter Setting ..........................................

134

16)

Soft Focus Setting ....................................

135

17)

Auto Set Up Mode Setting .......................

136

18)

Screen Position, Clock Frequency and

 

 

Clock Phase Adjustment ..........................

137

19)

Auto Function Mode Setting ....................

139

20)

PIP DETECT Setting .................................

140

21)

SPLIT FREEZE Setting ..............................

141

2

Table of Contents

5.4 Integrator Mode .......................................................

142

5.4.1 About the Integrator Mode .............................

142

5.4.2 Example of Integrator Mode Operation ..........

143

5.4.3 Adjustment and Setting in the Integrator

 

 

Mode ...............................................................

144

 

1)

PICTURE Adjustment ...............................

144

 

2)

WHITE BALANCE Adjustment .................

145

 

3)

COLOR DETAIL setting ............................

146

 

4)

GAMMA Setting .......................................

147

 

5)

SCREEN (Screen Position) Adjustment ....

148

 

6)

Brightness Enhancement (BRT. ENHANCE)

 

 

Setting at the Center of the Screen ..........

149

 

7)

SUB VOLUME Setting ..............................

150

 

8)

Program Timer Setting .............................

151

 

9)

SCREEN MASK Setting ............................

153

 

10)

SIDE MASK Setting ..................................

154

 

11)

VIDEO WALL Setting ...............................

156

 

12)

BAUD RATE Setting .................................

160

 

13)

Assigning an ID .........................................

161

 

14)

Cooling Fan Control Setting ......................

163

 

15)

OSD Display Setting .................................

164

 

16)

FRONT INDICATOR Setting .....................

166

 

17)

COLOR MODE Setting .............................

167

 

18)

PRO USE Setting ......................................

168

 

19)

FRC Setting ..............................................

170

 

20)

POWER ON MODE Setting ......................

172

 

21)

SEAMLESS SW Setting ............................

174

 

22)

MIRROR MODE Setting ...........................

175

 

23)

MULTISCREEN Setting ............................

177

 

24)

REPEAT TIMER Setting ............................

180

 

25)

FUNCTIONAL LOCK .................................

182

 

26)

Center Position Display ............................

183

5.4.4 PICTURE, White Balance and SCREEN Position

 

Adjustment Values Memory Area Tables .......

184

5.5 RS-232C Adjustment ................................................

189

5.5.1 About the RS-232C Adjustment ......................

189

5.5.2

Interface ..........................................................

190

5.5.3

Combination Connection .................................

191

5.5.4

ID Assignment ................................................

192

5.5.5 List of RS-232C Commands ............................

194

5.5.6

QUEST Commands .........................................

202

5.6 Screen Burning ........................................................

210

5.7 Precautions on Connecting Camera Images .........

212

5.8 Concerning frame delay (lip sync) ..........................

212

PRECAUTION

 

 

6.1 Precautions ...............................................................

213

MAINTENANCE

..................................................................

214

CAUTION

To prevent injury and material damage, thoroughly read this manual and all labels found on the equipment before attempting to mount, install, move, or adjust the product.

Do not install the unit outside or in the open air. Doing so will lead to water seepage into the system, resulting in fire or electric shock.

Be especially careful when working around parts of the system that have sharp edges.

When performing installation work from a height, take suitable precautions to guard against falling. Set up a barrier around the work site to prevent accidentally dropped objects that can injure people standing or walking below. Tampering with the unit may result in fire or electrical shock.

Keep all foreign objects out of the unit. Tampering with the unit may result in fire or electrical shock.

Observe the following operating environmental limitations:

Temperature: 0 °C to 40 °C Humidity: 20 % to 80 %

Install the unit only in properly ventilated areas.

3

Introduction

Introduction

The contents of “5.1 Before Beginning Adjustments (pg. 78)” and subsequent sections are premised on the PDP607CMX being equipped with the PDA-5003 or PDA-5004. Items that apply only when the PDA-5003 or PDA-5004 is installed are marked with a star ‘ ’.

Precautions

With the PDA-5003 or the PDA-5004 installed, the PDP-607CMX supports the following functions:

Input/output terminals

 

7 PDA-5003

 

 

 

INPUT 1

 

 

• Component video signal

Input

 

 

 

 

• RGB signals from AV devices other than PCs

INPUT 2

 

 

• Digital video signal (HDCP supported)

Input

 

 

 

 

 

INPUT 3

Input

 

• Y/C separate video signal

 

 

 

 

INPUT 4

Input

 

• Composite video signal

 

 

 

 

 

Output

 

• Composite video signal

 

 

 

 

INPUT 3/

Input

 

• Audio L/R signal

INPUT 4

 

 

 

 

 

 

 

INPUT 5

Input

 

• Composite video signal

 

 

 

• RGB signals from AV devices or PCs

 

 

 

• Audio L/R signal

7 PDA-5004

 

 

 

INPUT 1

 

 

• Component video signal

Input

 

 

 

 

• RGB signals from AV devices other than PCs

 

 

 

 

INPUT 2

Input

 

• Digital video signal (HDCP supported)

INPUT 3

 

 

• Y/C separate video signal

Input

 

 

 

 

• Audio L/R signal

INPUT 4

 

 

• Composite video signal

Input

 

 

 

 

• Audio L/R signal

 

 

 

 

 

Output

 

• Composite video signal

INPUT 5

 

 

• Composite video signal

Input

 

 

 

 

• RGB signals from AV devices or PCs

 

 

 

• Audio L/R signal

4

Features

Features and Functions of this device

Introduces newly developed Wide Plasma Panel

The new, wide, high-precision plasma panel (1365x768 / 16:9) pushes the envelope of previous high-luminance panels, producing brighter, clearer images with higher contrast.

ES Slot interface for enhanced potential

The display has a built-in ES Slot Interface to allow card installation for the connection of external devices, thus enhancing its expansion potential.

Supports wide range of computer signals (analog/digital)

This panel supports a wide range of signals including PC standard resolution XGA display, 1920x1080*1, 1360x768, wide signals, DOT BY DOT, full display, etc. It is possible to switch each signal between DOT BY DOT, 4:3, and full display*2.

*1 Only during DVI input of PC signals (compressed display)

*2 Screen size differs according to the signal

Free Installation Configuration

– Broader installation possibilities with thinner, lighter, high-endurance design –

While producing a large 60" screen image, the display is only 122 mm (4.8") thick, and weighs in at only 62.0 kg (136.7 lbs).

The efficient heat-radiating design greatly improves environmental operating conditions. The thinner, lighter design, coupled to high-endurance construction greatly broadens the range of possible installation locations and methods.

High reliability for commercial applications

This display has features that give it high dependability in commercial applications. These features include the ability to suppress peak luminance in accordance with the viewing program and to adjust the cooling fan’s speed with changes in operating environment. Such features provide safety and high-endurance under conditions of commercial use.

Improved usability

User convenience has been improved by adding features that make the display even more compatible with your computer. Some of these include the one-touch screen adjustment, [AUTO SET UP] function for computer connections, and the POINT ZOOM function to enlarge local portions of the screen image to display important detailed program data.

5

Specifications

2.1 Specifications

Light-emitting panel .....................

60V type AC Plasma Panel

 

 

 

131.86 cm (W) × 74.19 cm (H) × 151.3 cm (diagonal)

Aspect ratio

....................................................................

16 : 9

Pixels ......................................................................

 

1365 × 768

Pixel pitch .................

0.966 mm (H•RGB trio) × 0.966 mm (V)

Input/output terminals

 

Video-related

 

INPUT 1

 

 

 

 

 

 

 

 

Input

 

 

Mini D-sub, 15-pin connector (female)

 

 

 

 

• RGB signal (for SYNC ON G)

 

 

 

 

RGB ...............................

0.7 Vp-p/75 Ω/no sync

 

 

 

 

HD/VS, VD ........

TTL level/positive and negative

 

 

 

 

 

polarity/2.2 kΩ

 

 

 

 

SYNC ON G ............

1 Vp-p/75 Ω/negative sync.

 

 

 

 

*Microsoft Plug & Play (VESA DDC 1/2B) supported

 

 

 

 

 

 

Output

 

Mini D-sub, 15-pin connector (female)

INPUT 2

..................................

75 Ω/with buffer

 

 

 

 

 

 

 

 

Input

 

 

DVI-D 24-pin connector

 

 

 

 

Digital RGB signal (DVI compliant TMDS signal)

 

 

 

 

*Microsoft Plug & Play (VESA DDC 2B) supported

Audio-related

 

 

 

 

 

 

 

Input

 

 

AUDIO INPUT (for INPUT1)

 

 

 

 

Stero mini jack

500 mVrms/more than 10 kΩ

 

 

 

 

L/R ......................

 

 

 

 

AUDIO INPUT (for INPUT2)

 

 

 

 

Stero mini jack

 

 

 

 

 

L/R ......................

500 mVrms/more than 10 kΩ

 

 

 

 

 

 

 

Output

 

AUDIO OUTPUT

 

 

 

 

 

Stero mini jack

500 mVrms/less than 5 kΩ

 

 

 

 

L/R ..........................

 

 

 

 

SPEAKER

 

 

 

 

 

L/R ...................

6 Ω to 16 Ω/9 W + 9 W (at 6 Ω)

Control-related

RS-232C terminal: D-sub, 9-pin (male)

(NOTE 1)

Combination In/Out Terminal: Mini-DIN, 6-pin

Power requirements ...........

AC 100 V to 120 V, 50 Hz/60 Hz

(The power unit range is from AC100 V to 240 V (50 Hz/60 Hz))

In-rush ...............................................................

 

less than 50 A

Power factor ....................................................

 

more than 0.95

Consumption .........................

440 W (NOTE 2) (0.8 W in standby)

External dimensions

 

 

......................... 1470 mm (W) × 880 mm (H) × 122 mm (D)

57-7/8 in. (W) × 34-21/32 in. (H) × 4-26/32 in. (D)

Weight ........................................................

 

62.0 kg (136.7 lbs.)

Dimensions of packaging

 

 

....................... 1593 mm (W) × 1022 mm (H) × 434 mm (D)

62-23/32 in. (W) × 40-1/4 in. (H) × 17-3/32 in. (D)

Weight when packaged ............................

 

76.3 kg (168.2 lbs.)

Operating Temperature ....

0 °C to 40 °C (32 °F to 104 °F) (NOTE 3)

Operating Humidity ..........................................

 

20 % to 80 %

Operating atmospheric pressure ..........

800 hPa to 1100 hPa

Storage limitations (when installed)

 

Temperature ..................

–20 °C to +60 °C (–4 °F to 140 °F)

Humidity .........................................................

 

20 % to 90 %

Atmospheric pressure .........................

 

700 hPa to 1114 hPa

Storage limitations (when in original package)

Temperature ................

–30 °C to +60 °C (–22 °F to 140 °F)

Humidity .........................................................

 

20 % to 90 %

Atmospheric pressure .........................

 

700 hPa to 1114 hPa

Stacking ..............................................

 

Fewer than two tiers

Standard accessories

 

 

Power cord (2 m) ....................................................................

 

1

Ferrite core (for audio cables) .................................................

3

Remote control unit ................................................................

 

1

AA battery ...............................................................................

 

2

Wiping cloth (for screen) .........................................................

 

1

Speed clamp ...........................................................................

 

3

Bead band ...............................................................................

 

3

Operating instructions .............................................................

 

1

Warranty .................................................................................

 

1

Specifications and external designs are subject to change without notice.

(NOTE 1) The display is preset at the factory to 9600bps. This setting can be changed using either the remote control unit or a PC.

(NOTE 2) Allow for 500 W = 500 VA of consumption per unit. (NOTE 3) The correct operating environmental temperature may

vary depending on the installation site (refer to “Installation Site Requirements (pg. 15)”.

6

Specifications

INPUT Response Signals

INPUT 1

7 PC signals supported

Resolution

Refresh rate

Remark

(Dot x Line)

Vertical

Horizontal

 

 

 

 

 

 

 

 

 

640x400

70.1 Hz

31.5 kHz

NEC PC-9800

720x400

70.1 Hz

31.5 kHz

NEC PC-9800

 

 

85.1 Hz

37.9 kHz

 

640x480

59.9 Hz

31.5 kHz

 

 

 

66.7 Hz

35.0 kHz

Apple Macintosh 13”

 

 

72.8 Hz

37.9 kHz

 

 

 

75 Hz

37.5 kHz

 

 

 

85 Hz

43.3 kHz

 

 

 

100.4 Hz

51.1 kHz

I/O DATA

 

 

120.4 Hz

61.3 kHz

I/O DATA

848x480

60 Hz

31.0 kHz

 

852x480

60 Hz

31.7 kHz

 

800x600

56.3 Hz

35.2 kHz

 

 

 

60.3 Hz

37.9 kHz

 

 

 

72.2 Hz

48.1 kHz

 

 

 

75 Hz

46.9 kHz

 

 

 

85.1 Hz

53.7 kHz

 

 

 

99.8 Hz

63.0 kHz

I/O DATA

 

 

120 Hz

75.7 kHz

I/O DATA

832x624

74.6 Hz

49.7 kHz

Apple Macintosh 16”

1024x768

60 Hz

48.4 kHz

 

 

 

60 Hz

49.7 kHz

Work station (SGI)

 

 

70.1 Hz

56.5 kHz

 

 

 

75 Hz

60.0 kHz

( ) indicates Apple

 

 

(74.9 Hz )

(60.2 kHz)

Macintosh 19

 

 

85 Hz

68.7 kHz

 

 

 

100.6 Hz

80.5 kHz

I/O DATA

 

 

119.4 Hz

95.5 kHz

 

1280x768

56.2 Hz

45.1 kHz

 

 

 

59.8 Hz

48 kHz

 

 

 

69.8 Hz

56 kHz

 

1360x765

60 Hz

47.7 kHz

 

1360x768

60 Hz

47.7 kHz

I/O DATA

1376x768

59.9 Hz

48.3 kHz

I/O DATA

1280x800

59.8 Hz

49.7 kHz

CVT

1280x854

60 Hz

53.1 kHz

PC

1152x864

60 Hz

53.7 kHz

 

 

 

72 Hz

64.9 kHz

 

 

 

75 Hz

67.5 kHz

 

1152x870

75.1 Hz

68.7 kHz

Apple Macintosh 21”

1152x900

66 Hz

61.8 kHz

Sun Microsystems LO

 

 

76 Hz

71.7 kHz

Sun Microsystems HI

1440x900

59.9 Hz

55.9 kHz

Apple Macintosh 17”

1280x960

60 Hz

60.0 kHz

 

 

 

85 Hz

85.9 kHz

 

1280x1024

60 Hz

63.9 kHz

Work station (SGI)

 

 

60 Hz

64.0 kHz

 

 

 

60 Hz

64.6 kHz

Work station (EWS4800)

 

 

71.2 Hz

75.1 kHz

Work station (EWS4800)

 

 

72 Hz

78.1 kHz

Work station (HP)

 

 

75 Hz

80.0 kHz

 

 

 

76.1 Hz

81.1 kHz

Work station (SUN)

 

 

85 Hz

91.1 kHz

 

 

 

100.1 Hz

108.5 kHz

I/O DATA

1400x1050

60 Hz

65.3 kHz

 

 

 

74.9 Hz

82.3 kHz

 

 

 

85 Hz

93.9 kHz

 

1680x1050

60 Hz

65.3 kHz

 

1600x1200

60 Hz

75.0 kHz

 

 

 

65 Hz

81.3 kHz

 

 

 

70 Hz

87.5 kHz

 

 

 

75 Hz

93.8 kHz

 

 

 

85 Hz

106.3 kH z

 

1920x1200

59.9 Hz

74.6 kHz

CVT

1920x1200RB

60 Hz

74.0 kHz

CVT

INPUT 2

7 PC signals supported

Resolution

Refresh rate

Remarks

(Dot x Line)

Vertical

Horizontal

 

 

 

640x480

59.9 Hz

31.5 kHz

 

 

72.8 Hz

37.9 kHz

 

 

75 Hz

37.5 kHz

 

 

85 Hz

43.3 kHz

 

 

100.4 Hz

51.1 kHz

 

 

120.4 Hz

61.3 kHz

 

720x400

70.1 Hz

31.5 kHz

NEC PC-9800

 

85.1 Hz

37.9 kHz

 

848x480

60 Hz

31.0 kHz

 

852x480

60 Hz

31.7 kHz

 

800x600

56.3 Hz

35.2 kHz

 

 

60.3 Hz

37.9 kHz

 

 

72.2 Hz

48.1 kHz

 

 

75 Hz

46.9 kHz

 

 

85.1 Hz

53.7 kHz

 

 

99.8 Hz

63.0 kHz

 

 

120 Hz

75.7 kHz

 

1024x768

60 Hz

48.4 kHz

 

 

60 Hz

49.7 kHz

Work station (SGI)

 

70.1 Hz

56.5 kHz

 

 

75 Hz

60.0 kHz

 

 

85 Hz

68.7 kHz

 

 

100.6 Hz

80.5 kHz

 

 

119.4 Hz

95.5 kHz

 

1280x768

56.2 Hz

45.1 kHz

 

 

59.8 Hz

48 kHz

 

 

69.8 Hz

56 kHz

 

1280x800

59.8 Hz

49.7 kHz

 

1280x854

60 Hz

53.1 kHz

 

1360x768

60 Hz

47.7 kHz

I/O DATA

1376x768

59.9 Hz

48.3 kHz

I/O DATA

1152x864

60 Hz

53.7 kHz

 

 

72 Hz

64.9 kHz

 

 

75 Hz

67.5 kHz

 

1152x900

66 Hz

61.8 kHz

Sun Microsystems LO

 

76 Hz

71.7 kHz

Sun Microsystems HI

1440x900

59.9 Hz

55.9 kHz

Apple Macintosh17“

1280x960

60 Hz

60.0 kHz

 

 

85 Hz

85.9 kHz

 

 

60 Hz

63.9 kHz

Work station (SGI)

1280x1024

60 Hz

64.0 kHz

 

 

60 Hz

64.6 kHz

Work station (EWS4800)

 

71.2 Hz

75.1 kHz

Work station (EWS4800)

 

72 Hz

78.1 kHz

Work station (HP)

 

75 Hz

80.0 kHz

 

 

76.1 Hz

81.1 kHz

Work station (SUN)

 

85 Hz

91.1 kHz

 

1400x1050

60 Hz

65.3 kHz

 

 

74.9 Hz

82.3 kHz

 

1680x1050

60 Hz

65.3 kHz

 

1920x1080

50 Hz

56.2 kHz

 

 

60 Hz

67.5 kHz

 

1600x1200

60 Hz

75.0 kHz

 

1920x1200RB

60 Hz

74.0 kHz

CVT

7

External Dimensions

2.2 External Dimensions

WEIGHT: 62.0 kg (136.7 lbs) (without stand)

MATERIAL: Front: Resin; Rear cover: Metal plate, Front protector panel: Glass

TREATMENT: Front: Paint; Rear cover: Paint (All paints are Pioneer original colors)

For packaging information, refer to “3.3.2 Unpacking” (pg. 21).

(Unit: mm)

: center of gravity

 

30

TOP VIEW

 

1470

122.4

1372

 

1318.6

71.7

 

66.05

741.9

782

880

1513

390

 

 

LED

IR

45

 

 

7.5

7.5

61.7

LEFT SIDE VIEW

 

592.5

 

 

 

 

RIGHT SIDE VIEW

141.9

98

402.8

 

 

 

360

51

42

38 28

BOTTOM VIEW

99.3

45

367.8

12

 

17

850

500

8

REAR VIEW

<Main Unit Operation Panel>

109

98

30.3

<Connection panel>

367.8

402.8

External Dimensions

<Light Sensor for the remote/ambient light

sensor/indicator>

IR

LED

ø10

10.5

ø

2

 

135

150

17

 

 

45

 

99.3

1212 28

38

42

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

51

360

98

 

141.9

9

Controls and Connectors

2.3 Controls and Connectors

Main unit

3

Main unit

Operation panel on the main unit

STANDBY/ON

MENU

DISPLAY

INPUT SCREEN SIZE – VOL +

/ SET

 

 

 

 

 

4 506 7 8 9

2 1

Main unit

1 Remote control sensor

Point the remote control toward the remote sensor to operate the unit.

2 STANDBY/ON indicator

When the unit is operating: The indicator lights green.

When flashing, the light indicates an error.

The indicator flashes green once per second when the [POWER MGT.] function is operating.

When the unit is in Standby, the indicator lights red. When flashing, the light indicates an error.

3 Handles

Operation panel on the main unit

4 STANDBY/ON button ()

Press to put the display in Standby or into operation.

5 MENU button

Press to open and close the on-screen menu.

6 DISPLAY/SET button

Use to confirm on-screen menu selections and to change settings.

When not in use by on-screen menus, press to display the current set status.

7 INPUT () button

Except when menu screen is displayed, this button can change the input.

8 SCREEN SIZE () button

Except when menu screen is displayed, this button can change the screen size.

9VOL +/– (}/]) buttons

When not in use for by on-screen menus, these buttons can adjust the sound volume.

0 Functional lock button (concealed button)

This button is used to switch between permitted and blocked operation of the control panel and the remote control. It can also set the input function memory.

10

Controls and Connectors

Connection Panel

When installing PDA-5003

S-VIDEO

INPUT3

VIDEO

INPUT4

INPUT 3/4

AUDIO

 

 

ANALOG RGB

 

INPUT5

AUDIO

 

 

IN

OUT

R

L

G(ON SYNC)

B

R

HD (H/V SYNC) VD

R

L

~ ! @ #

$

%

When installing PDA-5004

S-VIDEO

INPUT3

AUDIO VIDEO

INPUT4

AUDIO

COMPONENT

INPUT5

AUDIO

 

 

VIDEO

 

 

R L

IN OUT

R

L

Y Pb/Cb

Pr/Cr

R

L

 

 

^

&

* (

)

 

_

 

 

+

-

=

 

 

 

 

 

 

 

 

 

IN

OUT

 

 

 

OUTPUT INPUT1 INPUT2

INPUT1

INPUT2

 

ANALOG RGB OUT

ANALOG RGB IN

DIGITAL RGB

 

(D-Sub)

(D-Sub)

(DVI-D)

COMBINATION

 

RS-232C

AUDIO AUDIO AUDIO

 

 

 

1

2

3

4

567

8

9

0

Plasma Display Section

1 COMBINATION IN/OUT

Never connect any component to these connectors without first consulting your Pioneer installation technician.

These connectors are used for Plasma Display setup adjustments.

2 SPEAKER (R) terminal

For connection of an external right speaker. Connect a speaker that has an impedance of 6 Ω to 16 Ω.

3 SPEAKER (L) terminal

For connection of an external left speaker. Connect a speaker that has an impedance of 6 Ω to 16 Ω.

4RS-232C

Never connect any component to this connector without first consulting your Pioneer installation technician.

This connector is used for Plasma Display setup adjustments.

5AUDIO (OUTPUT) (Stereo mini jack)

Use to output the audio of the selected source component connected to this unit to an AV amplifier or similar component.

Note: No sound is produced from the AUDIO (OUTPUT) jack when the MAIN POWER switch is set to OFF or when set to Standby.

6 AUDIO (INPUT1) (Stereo mini jack)

Use to obtain sound when INPUT1 is selected. Connect the audio output jack of components connected to INPUT1 to this unit.

7 AUDIO (INPUT2) (Stereo mini jack)

Use to obtain sound when INPUT2 is selected. Connect the audio output jack of components connected to INPUT2 to this unit.

8 ANALOG RGB OUT (INPUT1) (mini D-sub 15 pin)

Use the ANALOG RGB OUT (INPUT1) terminal to output the video signal to an external monitor or other component.

Note: The video signal is not output from the ANALOG RGB OUT (INPUT1) terminal when the panel's main power is OFF or the panel is in Standby.

9 ANALOG RGB IN (INPUT1) (mini D-sub 15 pin)

For connection of a personal computer (PC) or similar component. Confirm that the connection made corresponds to the signal output from the connected component.

0 DIGITAL RGB (INPUT2) (DVI-D jack)

Use this input to connect to a computer. Connect to an AV component (HDCP supported) equipped with DVI output connector.

-AC IN

Use to connect the supplied power cord to an AC outlet.

= MAIN POWER switch

Use to switch the main power of the unit on and

11

off.

Controls and Connectors

Video Card <PDA-5003> Section

The video card provides three video input connectors, one video output connector, and two audio input connectors. Consult the pages noted in parentheses ( ) for details regarding connections to the various jacks and connectors.

~S-VIDEO (INPUT3) (S-video jack)

Use this jack to connect components that have an S-video output jack such as a video deck, video camera, laser disc player, or DVD recorder.

!VIDEO IN (INPUT4) (BNC jack)

Use this jack to connect components that have a composite video output jack such as a video deck, video camera, laser disc player, or DVD recorder.

@VIDEO OUT (INPUT4) (BNC jack)

Use this jack to output the video signal to an external monitor or other component.

Note

The video signal is not output from the VIDEO OUT (INPUT4) jack when the display is OFF or in the Standby mode.

#AUDIO R/L (INPUT3/4) (RCA Pin jacks)

Use this jack to obtain sound when INPUT3 or INPUT4 is selected. Connect these jacks to the component’s audio outputs that are connected to the video card’s INPUT3 or INPUT4.

$ ANALOG RGB (INPUT5) (BNC jacks)

Use this jack to connect components equipped with RGB outputs jacks such as personal computers, external RGB decoders, or components equipped with component output jacks such as DVD recorders. Verify that the connection corresponds to the signal output from the connected component.

%AUDIO R/L (INPUT5) (RCA Pin jacks)

Use this jack to obtain sound when INPUT5 is selected.

Connect these jacks to the component’s audio outputs that are connected to the video card’s INPUT5.

Video Card <PDA-5004> Section

The video card provides three video input connectors, one video output connector, and three audio input connectors. Consult the pages noted in parentheses ( ) for details regarding connections to the various jacks and connectors.

^S-VIDEO (INPUT3) (S-video jack)

Use this jack to connect components that have an S-video output jack such as a video deck, video camera, laser disc player, or DVD recorder.

&AUDIO R/L (INPUT3) (RCA Pin jacks)

Use this jack to obtain sound when INPUT3 is selected.

Connect these jacks to the component’s audio outputs that are connected to the video card’s INPUT3.

*VIDEO IN (INPUT4) (RCA Pin jack)

Use this jack to connect components that have a composite video output jack such as a video deck, video camera, laser disc player, or DVD recorder.

( VIDEO OUT (INPUT4) (RCA Pin jack)

Use this jack to output the video signal to an external monitor or other component.

Note

The video signal is not output from the VIDEO OUT (INPUT4) jack when the display is OFF or in Standby.

) AUDIO R/L (INPUT4) (RCA Pin jacks)

Use this jack to obtain sound when INPUT4 is selected.

Connect these jacks to the component’s audio outputs that are connected to the video card’s INPUT4.

_ COMPONENT VIDEO (INPUT5) (RCA Pin jacks)

Use this jack to connect devices that have component video output jacks such as DVD recorders.

+AUDIO R/L (INPUT5) (RCA Pin jacks)

Use this jack to obtain sound when INPUT5 is selected.

Connect these jacks to the device’s audio outputs that are connected to the video card’s INPUT5.

12

Pin layout

2.4 Pin layout

INPUT1 (Mini D-sub, 15-pin connector; female)

pin layout

5

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RS-232C terminal (D-sub 9-pin connector; male)

pin layout (DCE format)

1 5

 

10

6

 

15

11

Pin No.

Input

Output

1R

2G

3B

4NC (not connected)

5 GND

6GND

7GND

8GND

9 DDC +5V

NC (not connected)

10GND

11NC (not connected)

12 DDC SDA

NC (not connected)

13HD or H/V SYNC

14VD

15 DDC SCL

NC (not connected)

Combination IN/OUT terminal pin layout

 

6

 

 

 

5

 

4

 

 

 

 

3

 

 

 

 

 

2

 

 

 

1

 

 

 

 

 

 

 

Pin No.

Combination

 

Combination

 

 

IN

 

OUT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

GND

 

GND

 

 

 

 

 

 

 

2

NC (not connected)

NC (not connected)

 

 

 

 

 

 

 

3

TxD (output)

 

RxD (input)

 

 

 

 

 

 

 

4

NC (not connected)

NC (not connected)

 

 

 

 

 

 

 

5

RxD (input)

 

TxD (output)

 

 

 

 

 

 

 

6

NC (not connected)

NC (not connected)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6

9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pin No.

 

 

 

 

 

 

 

 

Signal

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

NC (not connected)

 

 

 

 

 

 

 

 

2

TxD (Transmit Data)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

RxD (Receive Data)

 

 

 

 

 

 

 

 

4

NC (not connected)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

GND

 

 

 

 

 

 

 

 

6

NC (not connected)

 

 

 

 

 

 

 

 

7

NC (not connected)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8

RTS (Request To Send)

9

NC (not connected)

 

 

 

 

 

 

 

 

INPUT2 (DVI-D 24 pin connector; female)

pin layout

1 2

 

9

 

16

 

17

24

 

 

 

 

Pin No.

Signal Assignment

 

 

 

 

 

 

 

 

1

T.M.D.S. Data2–

 

 

2

T.M.D.S. Data2+

 

 

3

T.M.D.S. Data2/4 Shield

 

 

 

 

 

4

NC (No connection)

 

 

5

NC (No connection)

 

 

6

DDC Clock

 

 

7

DDC Data

 

 

8

NC (No connection)

 

 

9

T.M.D.S. Data1–

 

 

10

T.M.D.S. Data1+

 

 

11

T.M.D.S. Data1/3 Shield

 

12

NC (No connection)

 

 

13

NC (No connection)

 

 

14

+5V Power

 

 

 

 

 

 

15

GND

 

 

16

Hot Plug Detect

 

 

17

T.M.D.S. Data0 –

 

 

18

T.M.D.S. Data0+

 

 

19

T.M.D.S. Data0/5 Shield

 

 

 

 

 

20

NC (No connection)

 

 

 

 

 

 

21

NC (No connection)

 

 

 

 

 

 

22

T.M.D.S. Clock Shield

 

 

 

 

 

 

23

T.M.D.S. Clock+

 

 

 

 

 

 

24

T.M.D.S. Clock–

 

 

13

Remote Control Unit

2.5 Remote Control Unit

1 0

-

2

=

3

~

4

!

 

5

 

6

@

7

#

8

$

9

%

1 SCREEN SIZE button

Press to select the screen size.

2 INPUT buttons

Press to select the input.

3 MENU button

Press to reveal and hide the on-screen menu.

4ADJUST (5//3/2) buttons

Press to navigate menu screens and adjust various settings on the unit.

5SET button

Press to adjust or enter various settings on the unit.

6SUB INPUT button

Press to change subscreen inputs during multiscreen display.

7SPLIT button

Press to switch to multi-screen display.

8MUTING button

Press to mute the volume.

9ID NO. SET button

Press to select which position the panel holds in a video wall.

0 AUTO SET UP button

-

=

Press to automatically set the [POSITION], [CLOCK]. and [PHASE] to optimum values when using a computer signal.

STANDBY/ON button

Press to activate the display or place in Standby.

DISPLAY button

Press to view the unit’s current input and setup mode.

~

!

POINT ZOOM button

Press to select and enlarge a portion of the screen.

FREEZE button

Press to display a still image in the subscreen when the memo screen function is enabled.

@SWAP button

Press to switch between the main screen and the subscreen during multi-screen display.

# PIP SHIFT button

$

%

Press to move the position of the subscreen when viewing in PinP mode with multi-screen dsplay.

VOLUME (+/–) buttons

Press to adjust the volume.

CLEAR button

Press to clear for program timer and ID assignment.

14

Installation Site Requirements

3.1 Installation Site Requirements

If the site requires modifications or special preparations before installing the Plasma Display or its mounting hardware, obtain permission in advance from the building owner or building authorities. To ensure safety, it is also important to determine the strength of the installation site with the help of an authorized building contractor.

Safety Precautions

1) Structure of the installation site

Thoroughly study the structure of the installation site before determining the most suitable installation method. Buildings vary in structure and materials, thus the best mounting choice differs at each location. When drilling into walls, check for internal electrical wiring and hidden pipes.

2) Weight capacity of the installation site

Select a location sufficient to support the total weight of the display and mounting hardware.

3) Flat, level surfaces

Select a flat, level surface so that the mounting hardware is parallel to the proposed mounting surface.

Install the unit so that the load is evenly distributed along the ceiling or floor, as well as on mounting hardware such as from hang bolts.

4) Sufficient work space

Select a location with sufficient space for installation preperations. The panel mounting should be conducted by two or more people.

5) Nearby equipment

If air conditioning ducts, lamps, etc. are located near the installation site, dust, temperatures fluctuations, humidity, and condensation may cause problems. Please take steps to avoid this possibility.

6) Safe locations

Do not install the unit where it may be easily touched or leaned against. Avoid locations subject to high vibration or severe impacts.

7) Lighting conditions

Check existing lighting and sunlight angles when considering an installation layout. Bright lighting can reduce the visibility and quality of a displayed image.

In very bright surroundings, adjusting screen intensity may not result in perceptibly brighter images. Extreme intensity settings can reduce a system’s service life.

8) Other installation conditions

The panel is designed for indoor use and is not suited for open-air use. Installation in locations that are even partially exposed to the elements may lead to malfunctions or breakdown. If there is a danger of being subjected to the conditions listed below, it is necessary to limit the exposure as much as possible.

Water or other liquids and dust

Temperature and humidity changes

Salt-bearing wind

Direct sunlight (avoid sites exposed to direct sunlight upon the display as this can degrade image quality)

15

Installation Site Requirements

9) Temperature and humidity conditions

The installation site should meet the following conditions:

Operating temperatures: 0 °C to 40 °C (largely depending on installation conditions)

Operating humidity: 20 % to 80 %

Storage temperature: –20 °C to 60 °C

Storage humidity: 20 % to 90 %

Operating atmospheric pressure: 800 hPa to 1100 hPa

Storage atmospheric pressure: 700 hPa to 1114 hPa

We discourage installing electronic products such as this unit in locations subject to high humidity. If the unit is to be installed in a location subject to relatively high humidity, observe the following:

Failure to install the unit in acceptable ways may result in non-warranty damages.

Make sure the unit is grounded.

Do not allow water or other liquids to enter the unit.

10) Prevent condensation

A primary problem during the winter is condensation forming on or in electronic equipment. Rapid temperature fluctuations can leave water vapor inside the unit or on the screen, degrading performance. If condensation occurs, turn the unit OFF for an hour or more then increase the room temperature gradually before turning ON the unit.

Consult Pioneer authorized dealers for assistance.

11) Power requirements

This unit functions properly when powered at ±10 % of its rated voltage. Characteristics of power lines may effect the voltage output. If any of the following issues occur, contact an electrician to inspect the power source.

--Significant voltage drop between the circuit panel and the Plasma Display

--Significant changes in voltage when switching the display power ON or OFF

Please allow the following margin for power consumption per unit. 500 W = 500 VA

(NOTE)

When powering up the unit, the in-rush current is approximately 30 A.

A grounded three-core power cable is used by the Plasma Display in order to maintain its functions. Connect the power cord by inserting it into a grounded electrical outlet.

When using a different power source, use a conversion plug. Insert it into a grounded electrical outlet and securely attach the ground wire.

A leakage current within a value, stipulated by standards in each country, flows from an internal noise filter through devices installed inside switching power sources such as television sets or air-conditioners. Because these currents are added together when multiple units are connected, take steps to prevent electric shock caused by ground wires, etc. When a leakage breaker is installed in a power distribution series, choose the leakage breaker rating that is at least two times the total leakage current.

When many devices are connected, increase the number of leakage breakers and form branches in the wiring system.

12) Effective remote control distance

The remote control of this display receives at the following angles and distances.

Front: 8 m

Left-right 45°: 3 m/Left-right 30°: 7 m

Upward 30°: 3.5 m/Upward 15°: 5 m

Downward 30°: 5 m

If other products controlled with infrared remote controls are placed nearby, remote control function may be affected. In such cases, move other devices further away from the display or contact a Pioneer-authorized dealer for assistance.

Depending on installation conditions, the remote control range may be reduced by infrared radiation emitted by the screen.

The screen’s infrared intensity varies, depending upon the displayed image.

16

Installation Conditions

3.2 Installation Conditions

3.2.1 Heat dissipation

This unit has openings for effective ventilation. Vent locations are marked by arrows in the illustration below. The

arrows show the direction of airflow. To allow proper dissipation of heat from the unit, do not cover these openings.

(Unit : mm)

 

 

 

 

 

 

 

 

104.5

140.25

 

 

 

 

 

1176.4

 

 

 

 

 

 

 

 

 

 

744.4

 

 

 

 

 

108.4

36.4

124.4

92.4

124.4

124.4

92.4

124.4

36.4

108.4

 

 

44.6

 

 

 

 

 

 

 

 

 

A

 

A

 

 

 

 

A

 

A

 

 

 

 

 

 

 

 

 

 

 

94

FAN1

A

A

A

A

FAN2

 

 

 

 

 

 

 

 

FAN3

 

 

 

 

174.5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

409.5

 

 

 

 

 

 

114.5

164.5

 

 

407.75

64.4

216.35

227.75

404.4

66

 

In a standard installation, three fans and part A draw hot air from the unit. All openings not assisted by fans serve as air inlets. If the unit is hung from or embedded into a wall, special operating temperature limits and other limitations may apply. Refer to section “3.4 Special Installation” (pg. 24) for more information.

17

Installation Conditions

3.2.2 Calculating heat quantity

As a courtesy to our customers, we have included the power formula for calculating air conditioning needs. For power consumption, allow 500 W = 500 VA per unit.

Since most of the power consumed is transformed into heat, power consumption may be regarded as roughly equal to generated heat.

1 Conversion to calories [W] × 0.86 = [kcal/h]

Heat generated per display: 500 W × 0.86 = 430 kcal/h

2 Conversion to British Thermal Units [W] × 3.41 = [BTU/h]

Heat generated per unit: 500 W × 3.41 = 1705 BTU/h

3.2.3 Product mounting holes

We recommend using mounting hardware available from Pioneer. If you use other mounting hardware, mount the hardware to the unit using the M8-bolt holes on the unit. Tighten the bolts with a torque between 50 kg/cm and 80 kg/ cm. Applying a torque beyond these limits may lead to internal component failure.

Locations of usable mounting holes are shown below.

a Holes (4 places)

Vent (fan)

b Holes (8 places)

b hole*

 

b hole*

 

 

 

Attaching

 

 

surface

 

 

This unit

Installation

 

 

bracket etc...

 

 

 

 

 

a hole

 

 

Center line

Bolt

a holes

 

a holes

 

 

 

 

 

12 mm to

 

 

b hole

18 mm

 

 

Screw provided with

 

 

speaker unit (sold

 

Center line

separately)

b hole*

b hole*

 

 

 

Rear view diagram

Side view diagram

* only for speaker unit

Always use a minimum of 4 mounting holes that are evenly distributed on opposite sides of both the horizontal and vertical center lines.

Use bolts that are long enough to be inserted 12 mm (1/2 in.) to 18 mm (11/16 in.) in to main unit from the attaching surface for a holes. Refer to the side view diagram in the above illustration.

Do not block or cover vents on the rear panel.

Take precautions to prevent the walls from being soiled by the Plasma Display’s exhaust outlets.

This unit incorporates glass components. Install only on flat surfaces.

Always turn every bolt by hand two to three times then check to make sure the bolt is straight. You may tighten using a tool but do not over-tighten the bolts.

Do not use loctight or similar bonding products.

Please use M8 (P=1.25) bolts. DO NOT use any other type of bolt.

The panel is attached using M8 x 4.

For details, see the following page.

18

Installation Conditions

This unit is designed to be mounted using four bolt holes. For additional safety, we recommend securing it at four points on opposite sides of the horizontal and vertical center lines, as shown in the drawing below.

Methods of securing

Secured at four points

(with mounting hardware attached to the top and bottom)

*Attach using M8x4.

Secured at four points

(with mounting hardware attached to the sides) *Attach using M8x4.

Take proper precautions to prevent pinching the power cord or signal cables.

19

Installation Conditions

3.2.4 Mounting surface warping

The display incorporates glass. Before mounting the panel using hardware other than that provided by Pioneer, perform the following checks to confirm that the display is free from warps exceeding 1 mm*.

Regarding the 1 mm limit:

The panel frame may have a warp of up to 3 mm. If the total warp (the warp of the frame plus the warp of the mounting surface) exceeds 4 mm then the glass in the display may experience excessive stress. To ensure that the total warp is less than 4 mm, verify that the warp of the mounting surface is less than 1 mm.

1Referring to the illustration below, diagonally extend string (maximum diameter φ 0.1- mm) through the bolt mount openings. Strings should be completely free of slack.

2Measure the clearance (L) between the strings where they cross. Distortion is expressed by: [Distortion] = L × 2.

3If L is found to be 0, pass the strings through the other bolt mount openings then repeat the measurements. Any value of L greater than 0 indicates the presence of distortion. If the measured value in both cases is 0, the distortion is negligible.

A

Mount bolt holes

Plasma Display Mount Surface (Mount Brackets)

A

D

Magnified view of section A

 

String

 

 

 

Point E is the center point of string

F

 

 

 

segment A-B.

 

 

Point F is the center point of string

 

 

segment C-D.

E

 

Clearance between points E and F = L

 

(Points E and F are shown displaced

String

 

 

for illustrative purposes).

C

B

 

 

20

Installation Procedures

3.3 Installation Procedures

3.3.1 Transportation precautions

Once the shipping container is opened, transporting the unit in its packaging should be handled by two or more people. To avoid injury or damage, do not lift the package by its packing bands.

When transporting or storing the unit, always position it vertically - never horizontally. Horizontal transportation or storage invalidates the product warranty.

In transportation or storage of products in original packing, never stack more than two units high.

For transportation or storage, observe the warnings and instructions on the upper face of the carton.

The Plasma Display is made of glass. Please handle the panel carefully to prevent it from being damaged.

3.3.2 Unpacking

The original packing material can be re-used to safely ship the Plasma Display. When repacking, it is important to use the material in the same way as when the unit originally shipped. Failure to pack the panel correctly can damage the Plasma Display.

1) Packing specifications; 1593 mm (W) × 1022 mm (H) × 434 mm (D), 76.3 kg

Ref. No.

Terms

 

1

Upper Carton

1

2

Under Carton

 

3

Under Carton

19

 

 

 

4Pad

5Reinforce Carton

 

 

23

20

6

Mirror Mat

 

 

 

7

Pad

 

22

8

Power Cord

 

 

9

Remote Control Unit

 

3

 

 

 

10Accessory Case

11Vinyl Bag

12

Vinyl Bag’s Assembly

5

 

5

 

12

11

13

Wiping Cloth

 

4

 

 

 

21

 

 

 

14

Operating Instructions

 

 

 

 

13

 

15

Caution Sheet

 

 

 

 

14

 

 

 

 

 

 

 

15

 

16

Correction Sheet

6

 

 

8

16

 

 

 

17

 

17

Supplement Sheet

 

 

 

 

 

 

 

 

18

 

18

Warranty Card

 

 

 

 

 

 

 

 

 

 

 

19

Vinyl Bag (S)

 

 

 

7

 

 

20

Dry Cell Battery (R6P, AA)

 

 

 

 

10

 

 

 

 

 

 

 

 

21

Binder

 

7

 

 

 

 

22

Ferrite Core

 

 

 

 

 

 

23

Warranty Card

 

 

 

 

 

 

 

 

 

 

 

 

9

 

 

 

 

2

 

 

 

 

21

Installation Procedures

2)Unpacking procedures

1 Remove the packing bands.

2 Slowly lift and remove the upper carton.

3 Lift and remove the carton cover.

4 Remove the pads.

5 Remove the accessory and power cord cases.

6 Remove the unit (requires two or more people).

3)Transportation of the unpacked unit.

If it needs to be moved, the unit should be lifted by two or more people.

Caution

Never move the unit by dragging it along the floor.

Move the unit slowly, taking care to prevent scraping or striking the delicate front protective panel.

• In order to prevent adhesion of dust, remove the protective film only after all work and preparations for the installation site, including clean-up following unpacking, are complete.

• When moving the display, it should always be carried by two people holding the rear handles in the manner shown.

No!

Never attempt to move the Plasma Display by holding only one of the handles.

3.3.3 Re-packing (re-packing and re-shipping are not covered by the warranty)

If the unit needs to be re-packaged, observe the following guidelines.

Refer to the unpacking instructions in section “3.3.2 Unpacking” (pg. 21, 22). Pack the unit by reversing the unpacking procedure. There is a front and back to the miller mat. Place the shiny film surface facing out and the soft surface facing in towards the display glass.

Restore all accessories to their original locations. Secure with adhesive tape to prevent damage during transportation.

Do not re-package and ship if the packing material is damaged.

3.3.4Wiring

1)Connecting the power cable

Refer to the “ Power Cord Connection ” section in the operating instructions.

For power source specifications, refer to “3.1 Installation Site Requirements, Section 11) Power requirements” (pg. 16) earlier in this document.

2)Connecting signal cables

Refer to the operating instructions shipped with the unit for information on how to connect a PC or audio device.

Precautions when using long connecting signal cables

--Use coaxial cables. For video signals use 3 C-2 V cables for lengths up to 15 meters and 5 C-2 V cables for lengths up to 30 meters. Because computer signals are more likely to degrade than video signals, even if the cable is shorter than 15 m, the use of 5 C-2 V coaxial multi-cables (5BNC) is recommended. You can also improve signal quality by minimizing cable length.

--Video cables plugged into video inputs and outputs close to dimmers, neon signs, air-conditioning units, or cables for wired broadcasts may occasionally corrupt images.

3)Processing wires

For permanent or long-term installation, please select cables of the correct length and consider the entire wiring route. This is not as important for temporary or short-term installations such as at special events.

Arrange and secure cables so that they are not subject to pinching or physical force. For temporary installations, securing cables with string is adequate. For permanent installations, secure by more reliable means.

22

Installation Procedures

4) Arranging and securing cables with speed clamps and bead bands

Fasten cables using the supplied speed clamps.

Once speed clamps are fastened, they are

not easily removed.

* As viewed from the rear of the display.

1 2

1.Organize cables together using the provided speed clamps.

Insert 1 into an appropriate hole on the rear of the unit then snap 2 into the back of 1 to fix the clamp.

Speed clamps are designed to be difficult to undo once in place. Please attach carefully.

To attach the speed clamps to the main unit

Connect the speed clamps using the 4 holes marked with “‡” below, depending on the situation.

2.Bunch separated cables together and secure them with the provided bead bands.

Do not allow excessive stress to be placed on the ends of cables.

Note

Cables can be routed to the right or left.

* As viewed from the rear of the display.

To remove speed clamps

Using pliers, twist the clamp 90° and pull outward.

In some cases, the clamp may have deteriorated over time. Removed speed clamps may not be re-usable.

23

Special Installation (Mounting to fittings)

3.4 Special Installation

The unit can be hung from or embedded in a wall. However, some installations impose additional limitations on operating temperatures and other factors.

Examine installation methods and the ambient conditions for your installation site. Refer to sections “3.1 Installation Site Requirements” (pg. 15), ”3.2 Installation Conditions” (pg. 17), and “3.3 Installation Procedures” (pg. 21) in this manual.

Measurements discussed in this manual assume the following conditions:

A 100 % white input is supplied.

Sufficient aging has been completed.

Make all measurements under identical conditions. The aging period required for correct measurement is about two and a half hours, depending on the time available at the installation site.

3.4.1 Mounting to fittings

Observe the following guidelines when mounting the unit to fittings. Notes 2 to 8 apply to all cases of mounting to fittings.

1 Remove any objects from around the panel within a distance of 300 mm.

2 Any unit deformation/warping occurring as a result of installation should be less than 4 mm.

3 Never block or cover vents or other openings aside from those shown as blocked in the illustrations on the following page.

4 The fittings should have a thickness of less than 20 mm.

(This limit does NOT apply to fitting in examples 1 and 4 on the following page.)

5 L-shaped fittings should have a thickness of less than 100 mm. 6 The strength of the fittings should be adequate to bear the weight

of the display.

7 Take precautions to avoid sharply bending the power cable.

8 If necessary, remove the handles. When reinstalling the handles, completely tighten the screws for safety.

Operating environment for standard installation

Ambient Temperature: 0 °C to 40 °C (examples 1 and 2)

Operating environment for vertical installation (*1)

Ambient Temperature: 0 °C to 40 °C (vertical installation: examples 3 and 4)

The operating temperature restrictions for the speaker system (PDP- S55-LR) are the same regardless of whether installation is horizontal or vertical.

*1 For this installation, set the ‘FAN CONTROL’ to ‘MAX’ as shown in “5.4.3 Adjustment and Setting in the Integrator Mode 14) Cooling Fan Control Setting (pg. 163)”.

4 mm MAX

Maximum allowable deformation/ warping is 4 mm.

Less than

20 mm

(No thickness limitations in examples 2 and 4 on the following page.)

Less than

20 mm

(No thickness limitations in examples 2 and 4 on the following page.)

Less than

100 mm

L-shaped fitting

Note

When a video card other than PDA-5003/PDA-5004 is used, the operating temperature conditions given above may vary. Check the video card operating instructions for the conditions.

Arrange the power cable so that minimum stress is placed on it.

24

Special Installation (Mounting to fittings)

Standard installation

(In cases where top and bottom are reversed)

 

Example 1

Example 2

35 mm or

 

 

less

 

35 mm or

 

 

less

 

Vertical installation

 

 

Example 3

Example 4

35 mm or

 

 

less

35 mm or less

Attach so that the fan is on the left side when viewed from the rear.

25

Special Instruction (Hanging on the wall)

3.4.2 Hanging on the wall

Carefully read the following imformation before attempting to hang the unit on a wall. Take note of the various limitations specified in this section. Mount the unit so that twisting, bending, or any other warping does not exceed 4 mm.

A

 

B

 

 

 

880

 

 

 

50

 

 

 

 

162

 

C

25

D

 

 

Shaded areas indicate attachment points for mounting hardware.

: Thermometer (temperature measurement point)

1470

D

Operating temperature restrictions

Standard single-unit installation

Distance from wall (A)

B

C

D

Ambient temperature

 

 

 

 

 

50 mm or less

300 mm or more

300 mm or more

300 mm or more

0 °C to 35 °C

 

 

 

 

 

50 mm or more

100 mm or more

50 mm or more

50 mm or more

0 °C to 40 °C

 

 

 

 

 

Requirements when used with PDP-S55-LR speaker system

When installed as a single unit, all requirements are the same as those listed above for horizontal/ vertical, left/right reverse installations. However, the figures listed above indicate the distance between the speakers and the wall.

Note

Different temperature restrictions apply to the PDK-WM03. Refer to “4.5 Wall Mount Unit PDK-WM03” (pg. 68). For a wall-mount installation, allow adequate space (a clearance of 300 mm or more) above, below, and to each side of the panel.

26

Special Installation (Hanging on the wall)

Methods of Securing: Basic methods of securing the panel to a wall are shown below. Avoid blocking or covering areas aside from those indicated by . Before attaching the unit to fittings, double-check that the thickness and height of the fittings and the number of fixing bolts is correct.

(Also refer to “3.4.1 Mounting to fittings” (pg. 24).)

Note

Heated air is drawn from the interior of the unit by fans. Before installation, consider the heat resistance of the wall or other surface behind the unit. Exhaust temperatures can be 30 °C higher than the outside temperature.

Note

For wall-mounting, do not bundle the cables in a way that block vents.

300 mm or

more

300 mm or

more

Flush-wall installation

(distance between unit and wall

less than 50 mm)

Requirements :

Free air flow (With no obstructions within a distance of 300 mm from the unit’s sides, top and bottom)

Temperature of 0 °C to 35 °C

100 mm or more

50 mm or

more

50 mm or

more

50 mm or more

Ex.: Installation requirements when

installed in wall recess

Wall-mounted installation

(distance between unit and wall

greater than 50 mm)

Requirements :

Free air flow (With no obstructions within a distance of 300 mm from the unit) around all four sides of the unit is not necessarily required when the unit is installed at a distance of greater than 50 millimeters away from the wall.

*However, in such cases, the unit may not be placed behind a glass panel or any other obstruction which would create an enclosed space.

• Temperature of 0 °C to 40 °C

Panting net

100 mm or more

100 mm or more

 

100 mm or more

100 mm or more

 

Ex.: Installation when covered with a

Panting net

Wall-embedded installation

(i.e., installation in closed space)

(distance between unit and wall

greater than 50 mm)

Requirements :

See “3.4.3 Embedding in the wall” (pg. 28) for installation requirements.

Temperature of 0 °C to 40 °C

27

Special Installation (Embedding in the wall)

3.4.3 Embedding in the wall

Carefully read the following imformation before trying to embed the unit in a wall. Observe all the limitations specified below.

Be sure to mount the unit so that twisting, bending, or other deformation of the unit does not exceed 4 mm.

(1)Embedding in walls with space provided behind the unit (no obstructions within a distance of 300 mm from the back surface of the unit).

X (Front of the unit)

A

A

Y (Rear of the unit)

A

<Viewed from Above>

Operating Temperature Restrictions

 

Temperature in space X and Y

 

 

 

 

A: 0 mm to 370 mm

0 °C to 40 °C

 

 

* The same operating temperature restrictions apply to the speaker system (PDP-S55-LR).

A

<Viewed from the Right Side>

Methods of Securing: Basic methods of securing are shown below. Avoid blocking or covering areas aside from those indicated by .

Before attaching the unit to fittings, double-check that the thickness and height of the fittings, and the number of bolts is correct.

(Also refer to “3.4.1 Mounting to fittings” (pg. 24).)

28

Special Installation (Embedding in the wall)

Temperature Measurement Points (Illustration for reference purposes)

: Thermometer (temperature measurement point)

50 mm 50 mm

Make measurements at a distance of 50 mm from the unit without directly subjecting the thermometer to fan exhaust.

For spaces where temperature fluctuations are likely, gather additional measurement points for adequate data.

29

Special Installation (Embedding in the wall)

(2) Embedding in walls with no space provided behind the unit.

Panting (Punching) net (numerical aperture 50 % or over)

100 mm or more

100 mm or more

 

100 mm or

100 mm or

50 mm or

more

more

more

 

 

Cation : Due to possible heat issues, we do not recommend installing the panel in narrow, enclosed areas.

Operating Temperature Restrictions

Ambient temperature: 0 °C to 40 °C

The same operating temperature restrictions apply to the speaker system (PDP-S55-LR).

Methods of Securing: Basic methods of securing are shown below. Avoid blocking or covering areas aside from those indicated by . The methods indicated by a large “X” must not be used.

Before attaching the unit to fittings, double-check that the thickness and height of the fittings and the number of bolts is correct.

(Also refer to “3.4.1 Mounting to fittings” (pg. 24).)

Installation is not possible

30

Special installation (When the display is put in a box)

3.4.4 When the display is put in a box

Operating this display in confined spaces is not recommended.

• If the display is to be used in a confined space, observe the following conditions shown in the drawing below: A 50

B 50

C 10

D 50

Use a mesh with aperture efficiency of 50 % or more.

If hot air remains in the enclosed space, the temperature may rise causing a malfunction or fire. As a precaution, the inner wall should have sufficient heat resistance or fire resistance.

Usage temperature conditions (BOX air temperature)

Ambient temperature: 0 °C to 35 °C

: Thermometer

Outside air temperature

measuring point

(temperature measurement point)

 

 

10 mm

Exhaust side

Intake side

 

 

 

A 50

 

 

B 50

 

 

C 10

A

A

D 50

Rear view (the following area should be made of mesh)

A+

800 mm or more

50 mm

A+

800 mm or more

50 mm

B

 

10 mm

B

 

C

D

Mesh with aperture efficiency A+ of 50 % or more

50 mm

B+

30 mm

100 mm

or more

100 mm

or more

B+

50 mm

A+ 50 mm

31

Special Installation (Ceiling suspension with wires)

3.4.5 Ceiling suspension (with wires)

When suspending with wire, attach the unit either at rows A and B or at rows C and D to keep it from warping. In addition, the unit must be attached at four or more points, with these points distributed symmetrically on opposite

sides of the vertical and horizontal center lines.

A B

Attach so that the fan is on the left side when viewed from the rear.

C D

A

B

When suspending from a ceiling with wire, use the brackets shown below to prevent concentrating loads on the upper two fixing points.

For additional safety, secure the wires to separate fittings or parts of the ceiling.

Use mounting screws of material stronger than soft steel and use hexagonal bolts.

Use wires adequate for the combined weight of the panel and the weight of the support brackets.

No!

When installing the Plasma Display, DO NOT use the handles as means of hanging the display.

Wires

Wires

Screws

Screws

Brackets

Brackets

Operating environment for standard installation

Ambient Temperature: 0 °C to 40 °C

Operating environment for vertical installation (*1)

Ambient Temperature: 0 °C to 40 °C

*1 For this installation, set the ‘FAN CONTROL’ to ‘MAX’ as shown in “5.4.3 Adjustment and Setting in the Integrator Mode 14) Cooling Fan Control Setting” (pg. 163).

32

Special Installation (Ceiling suspension with wires)

Methods of Securing: Basic methods of securing are shown below. Avoid blocking or covering areas aside from those indicated by . The methods indicated by a large “X” must not be used.

Before attaching the unit to fittings, double-check that the thickness and height of the fittings, and the number of bolts is correct.

(Also refer to “3.4.1 Mounting to fittings” (pg. 24).)

Horizontal suspension

Vertical suspension

Installation is not possible

Attach so that the fan is on the left side when viewed from the rear.

33

Special Installation (Hanging on the wall lengthwise)

3.4.6 Hanging on the wall lengthwise

Carefully read the following imformation before attempting to mount the unit on the wall. Observe the various limitations

specified below.

Be sure to mount the unit so that twisting, bending, or any other deformation does not exceed 4 mm.

Shaded areas indicate attachment points for mounting hardware. : Thermometer (temperature measurement point)

Attach so that the fan is on the left side when viewed from the rear.

35.8

B

1470

Avoid blocking or covering this area on the upper and lower sides.

35.8

30.4

162

25

C

 

 

 

 

 

 

 

10

D

880

 

D

 

10

A

Operating Temperature Restrictions (*1)

Distance from wall (A)

B

C

D

Ambient temperature

50 mm or more

100 mm or more

50 mm or more

50 mm or more

0 °C to 35 °C

 

 

 

 

 

*1 For this installation, set the ‘FAN CONTROL’ to ‘MAX’ as shown in “5.4.3 Adjustment and Setting in the Integrator Mode 14) Cooling Fan Control Setting” (pg. 163).

34

Special Installation (Hanging on the wall lengthwise)

Methods of Securing: Basic methods of securing are shown below. Avoid blocking or covering areas aside from those indicated by . The method indicated by a large “X” must not be used.

Before attaching the unit to fittings, double-check that the thickness and height of the fittings and the number of bolts is correct.

(Also refer to “3.4.1 Mounting to fittings” (pg. 24).)

Installation is not possible

Note

Heat air is drawn from the interior of the unit by fans. Before installation, consider the heat resistance of the wall or other surface behind the unit. Exhaust temperatures can be 30 °C higher than the outside temperature.

Note

For wall-mounting, do not bundle the cables in a way that block vents.

35

Special Installation (Place product upright and flush, embedded in the wall)

3.4.7 Place product upright and flush into wall (embedding in the wall)

Carefully read the following instructions before trying to embed the unit in a wall. Observe all the limitations specified

below.

Be sure to mount the unit so that twisting, bending, or other deformation of the unit does not exceed 4 mm.

(1)Embedding in walls with space provided behind the unit (with no obstructions within a distance of 300 mm from the back surface of the unit)

A

X (Front of the unit)

A

 

 

A

Y (Rear of the unit)

<Viewed from Above>

A

<Viewed from the Right Side>

Operating Temperature Restrictions (*1)

Temperature in space X and Y

A: 0 mm to 370 mm

0 °C to 40 °C

*1 For this installation, set the ‘FAN CONTROL’ to ‘MAX’ as shown in “5.4.3 Adjustment and Setting in the Integrator Mode 14) Cooling Fan Control Setting” (pg. 163).

36

Special Installation (Place product upright and flush, embedded in the wall)

Methods of Securing: Basic methods of securing are shown below. Avoid blocking or covering areas aside from those indicated by . The methods indicated by a large “X” must not be used.

Before attaching the unit to fittings, double-check that the thickness and height of the fittings and the number of fixing bolts is correct.

(Also refer to “3.4.1 Mounting to fittings” (pg. 24).)

Installation is not possible

Attach so that the fan is on the left side when viewed from the rear.

37

Special Installation (Place product upright and flush, embedded in the wall)

(2) Embedding in walls with no space provided behind the unit

100 mm or more

Attach so that the fan is on the left side when viewed from the rear.

Panting (Punching) net (numerical aperture 50 % or over)

100 mm or more

100 mm or more

100 mm or more

50 mm or more

Cation : Due to possible heat issues, we do not recommend installing the panel in narrow, enclosed areas.

Operating Temperature Restrictions (*1)

• Ambient temperature: 0 °C to 35 °C

*1 For this installation, set the ‘FAN CONTROL’ to ‘MAX’ as shown in “5.4.3 Adjustment and Setting in the Integrator Mode 14) Cooling Fan Control Setting” (pg. 163).

38

Special Installation (Place product upright and flush, embedded in the wall)

Methods of Securing: Basic methods of securing are shown below. Avoid blocking or covering areas aside from those indicated by . The methods indicated by a large “X” must not be used.

Before attaching the unit to fittings, double-check that the thickness and height of the fittings and the number of bolts is correct.

(Also refer to “3.4.1 Mounting to fittings” (pg. 24).)

Installation is not possible

Attach so that the fan is on the left side when viewed from the rear.

39

Special Installation (Installed facing upward)

3.4.8 Installed facing upward

(1) When installed on top of a horizontal surface <an open space other than a horizontal surface>

surface Horizontal

50 mm or more

Horizontal surface

Operating Temperature Restrictions (*1)

Ambient temperature: 0 °C to 35 °C

The same operating temperature restrictions apply to the speaker system (PDP-S55-LR).

*1 For this installation, set the ‘FAN CONTROL’ to ‘MAX’ as shown in “5.4.3 Adjustment and Setting in the Integrator Mode 14) Cooling Fan Control Setting” (pg. 163).

Methods of Securing: Basic methods of securing are shown below. Avoid blocking or covering areas aside from those indicated by .

Before attaching the unit to fittings, double-check that the thickness and height of the fittings and the number of bolts is correct.

(Also refer to “3.4.1 Mounting to fittings” (pg. 24).)

40

Special installation (Installed facing upward)

(2) When the Plasma Display is in a confined space

Operating this display in confined spaces is not recommended.

• If the display is to be used in confined spaces, observe the following conditions shown in the drawing below: A 50

If heat remains in the enclosed space, the temperature may rise causing a malfunction or fire. As a precaution, the inner wall should have sufficient heat resistance or fire resistance.

Leave a space at least 10 mm wide when installing glass etc. on the front of the Plasma Display.

Usage temperature conditions (*1)

Ambient temperature: 0 °C to 35 °C (Outside air temperature)

Space enclosed by the back surface of the Plasma Display: 0 °C to 35 °C (Use a fan etc. to discharge air to maintain this temperature range.)

*1 For this installation, set the ‘FAN CONTROL’ to ‘MAX’ as shown in “5.4.3 Adjustment and Setting in the Integrator Mode 14) Cooling Fan Control Setting” (pg. 163).

: Thermometer (temperature measurement point)

Outside air temperature measuring point

Outside air

Enclosed space air

temperature

measuring point

temperature measuring

 

point

150 mm

10 mm

 

 

A

 

A 50

50 mm

Enclosed space air temperature measuring point

Note

When installing the Plasma Display facing upwards, do not place anything on top of it nor apply any load on it from

above.

41

Special installation (Horizontal connections)

3.4.9 Horizontal connections

While the display is designed to accommodate side-by-side installations, keep in mind that specific installation

configurations may affect ventilation. Observe the following requirements:

1Installation of up to two units (Horizontal connection)

The following table lists the operating temperature conditions when installing more than one panel. Use the units under conditions that keep the outside atmosphere in this range.

A

 

 

Unit A

 

Unit B

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Operating Temperature Restrictions

Distance from wall (A)

Ambient temperature

 

 

50 mm or more

0 °C to 40 °C

2Installing three or more units (Horizontal connection)

The following table lists the operating temperature conditions. Use the units under conditions that keep the outside atmosphere in this range.

A

 

 

Unit A

 

Unit B

 

Unit C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Operating Temperature Restrictions

Distance from wall (A)

Ambient temperature

50 mm or more

0 °C to 40 °C

42

Special installation (Multiple)

3.4.10 Multiple

While the display is designed to accommodate side-by-side installations, keep in mind that specific installation

configurations may affect ventilation. Observe the following requirements:

1Installing multiple (Two vertical units)

The following table lists the operating temperature conditions when installing more than one panel. Use the units under conditions that keep the outside atmosphere in this range.

A

Partition

Unit A

 

Unit B

 

Unit C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

In case of lateral connections, ensure that left and right partitions are provided.

To prevent heat venting from one video wall plasma panel into another panel, each display must be oriented in the same direction.

In the above example, each panel is shown with the Pioneer logo at the bottom.

Operating Temperature Restrictions

Distance from wall (A)

Ambient temperature

 

 

50 mm to 300 mm or less

0 °C to 35 °C

 

 

300 mm or more

0 °C to 40 °C

 

 

43

How to use the standard mounting components

4.1 Standard Mounting Components Features and Characteristics

In addition to reliability and vivid display resulting from its large screen area, brightness, and image quality, the Plasma Display (PDP-607CMX) is thin and lightweight. This panel can be mounted in locations not possible for conventional displays.

We considered various mounting patterns and operating conditions during the design of the Plasma Display (PDP607CMX). A wide range of standard mounting hardware is available for easy mounting.

Video Card: PDA-5003/PDA-5004

The video card makes video input and analog RGB input possible.

This product has a total of three lines: a COMPOSITE (1), S INPUT (1), and an analog RGB INPUT or COMPONENT INPUT (1). Furthermore, it can handle three line or two line audio, thus increasing the uses for video presentations.

Table Top Stand: PDK-TS26

This vertically installed type onboard stand is a perfect match to the 60-inch Plasma Display.

Wall Mount Unit: PDK-WM03

This wall mount unit is made for the 60-inch Plasma Display. It fixes the rear surface of the plasma display 45 mm from the wall. It is equipped with a variety of installation holes so it can be used on different kinds of walls. This structure simplifies attaching it to the Plasma Display.

Speaker System: PDP-S55-LR

This is a speaker system designed for use with the 60-inch Plasma Display.

2-way speakers feature 5 cm (2 in.) tweeter and 8 cm (3-3/16 in.) woofer in a vertical arrangement.

44

Handling the Standard Mounting Components

4.2 Handling the Standard Mounting Components

4.2.1 Handling precautions

This section of the manual discusses ways to mount, install, and handle the mounting hardware exclusively designed for Pioneer Plasma Displays. Mounting should be performed by qualified experts.

Refer all installation and mounting work to qualified installers, or request assistance from a Pioneer dealer.

4.2.2 Precautions for installation contractors

1)Before installation

Observe the specifications supplied in “3.1 Installation Site Requirements” earlier in this manual.

2)During Installation

Carefully read and observe the contents of this section of the manual. The installation work should be performed by two or more people.

3)After installation

After installation the mounting hardware, check for adequate strength and properly tightened screws. Repeat this inspection after mounting the display.

4)Delivering to the customer (1)Explaining mounting precautions

The mounting contractor is responsible for explaining the following precautions to the customer after mounting and installation work is complete. Even if the particulars of an installation are letter-perfect, your work may be perceived as inadequate unless you patiently and thoroughly explain these precautions to the customer.

The following are highly dangerous and must be avoided at all times:

• Any sudden application of force, including pushing and pulling

• Splashing water on the unit

• Placing any object on the unit

• Touching mount screws and other mounting hardware

For worry-free use of the unit:

If problem arises, the user should immediately ask the installation contractor to inspect the unit and make repairs if necessary.

To guard against accidents, ask the customer avoid making tilt or height adjustments. Changes should be referred to the installation contractor.

(2)Mounting contractor contact form

As the mounting and installation contractor, please complete the contractor contact form supplied with the unit and give it to the end-user after post-installation inspections are complete.

(3)Periodic inspections

Over time, aging of various components of the suspension/mounting hardware that may not be readily visible can render the installation unreliable. This may lead to the display breaking free of its mounting. Please recommend periodic inspections.

45

Video Card: PDA-5003/PDA-5004

4.3 Video Card: PDA-5003/PDA-5004

4.3.1 Specifications

External dimensions .................

PDA-5003: 301.5 mm (W) × 27.6 mm (H) × 148.9 mm (D)

 

(11-7/8 in. (W) × 1-3/32 in. (H) × 5-7/8 in. (D))

 

PDA-5004: 301.5 mm (W) × 27.6 mm (H) × 148.3 mm (D)

 

(11-7/8 in. (W) × 1-3/32 in. (H) × 5-27/32 in. (D))

Weight .......................................

0.4 kg (14 oz)

Dimensions of packaging .........

359 mm (W) × 68 mm (H) × 234 mm (D)

 

(14-1/8 in. (W) × 2-11/16 in. (H) × 9-7/32 in. (D))

Package weight .........................

1.4 kg (3.1 lbs.)

Input/Output jacks

7PDA-5003 Video-related

INPUT1

Input

 

The following signal is supported only when a PDA-5003 is installed.

 

 

 

 

• Component video signal

 

 

 

 

 

Y ........................

1 Vp-p/75 Ω/negative sync.

 

 

 

 

PB/CB, PR/CR ........

0.7 Vp-p (color 100 %)/75 Ω

 

 

 

 

 

 

INPUT2

Input

 

DVI-D 24-pin connector

 

 

 

 

 

Digital video signal (HDCP supported)

 

 

 

 

INPUT3

Input

 

S-VIDEO jack (Mini-DIN, 4-pin connector)

 

 

 

 

• Y/C separate video signal

 

 

 

 

 

Y ........................

1 Vp-p/75 Ω/negative sync.

 

 

 

 

C ........................

0.286 Vp-p/75 Ω (NTSC)

 

 

 

 

 

0.3 Vp-p/75 Ω (PAL)

 

 

 

 

 

 

INPUT4

 

Input

 

BNC jack

 

 

 

 

 

 

• Composite video signal

1 Vp-p/75 Ω/negative sync.

 

 

 

 

 

 

 

 

 

 

75 Ω/with buffer

 

 

Output

BNC jack ..................................

 

INPUT5

 

 

 

BNC jack × 5

 

 

 

Input

 

 

 

 

 

 

• RGB signal (for SYNC ON G)

 

 

 

RGB ...........................

0.7 Vp-p/75 Ω/no sync.

 

 

HD/VS, VD .................

TTL level/positive and negative polarity/75 Ω or 2.2 kΩ

 

 

 

(with impedance switching)

 

 

SYNC ON G ...............

1 Vp-p/75 Ω/negative sync.

 

 

• Component video signal

 

 

Y ................................

1 Vp-p/75 Ω/negative sync.

 

 

PB/CB, PR/CR ................

0.7 Vp-p (color 100 %)/75 Ω

Audio-related

 

 

 

AUDIO INPUT (for INPUT3/4)

 

Input

 

 

Pin jack (×2)

 

 

L/R

............ 500 mVrms/more than 10 kΩ

 

AUDIO INPUT (for INPUT5)

 

 

Pin jack (×2)

 

 

L/R ............

500 mVrms/more than 10 kΩ

46

Video Card: PDA-5003/PDA-5004

7PDA-5004 Video-related

INPUT1

Input

 

The following signal is supported only when a PDA-5004 is installed.

 

 

 

 

• Component video signal

 

 

 

 

 

Y ........................

1 Vp-p/75 Ω/negative sync.

 

 

 

 

PB/CB, PR/CR ........

0.7 Vp-p (color 100 %)/75 Ω

 

 

 

 

 

 

INPUT2

Input

 

DVI-D 24-pin connector

 

 

 

 

 

Digital video signal (HDCP supported)

 

 

 

 

 

 

 

 

INPUT3

Input

 

S-VIDEO jack (Mini-DIN, 4-pin connector)

 

 

 

 

• Y/C separate video signal

 

 

 

 

 

Y ........................

1 Vp-p/75 Ω/negative sync.

 

 

 

 

C ........................

0.286 Vp-p/75 Ω (NTSC)

 

 

 

 

 

0.3 Vp-p/75 Ω (PAL)

 

 

 

 

 

 

 

INPUT4

Input

 

RCA jack

 

 

 

 

 

 

• Composite video signal

1 Vp-p/75 Ω/negative sync.

 

 

 

 

 

 

 

 

 

 

75 Ω/with buffer

 

 

Output

RCA jack ..................................

 

 

 

 

 

 

 

INPUT5

Input

 

RCA jack

 

 

 

 

 

 

• RGB

0.7 Vp-p/75Ω/no sync.

 

 

 

 

 

 

 

 

SYNC ON G .......

1 Vp-p/75 Ω/negative sync.

 

 

 

 

• Component video signal

 

 

 

 

 

Y ........................

1 Vp-p/75 Ω/negative sync.

 

 

 

 

PB/CB, PR/CR ........

0.7 Vp-p (color 100 %)/75 Ω

Audio-related

 

 

 

 

 

 

 

 

Input

 

AUDIO INPUT (for INPUT3)

 

 

 

 

Pin jack (×2)

 

 

 

 

L/R ............

500 mVrms/more than 10 kΩ

 

 

AUDIO INPUT (for INPUT4)

 

 

 

 

Pin jack (×2)

 

 

 

 

L/R ............

500 mVrms/more than 10 kΩ

 

 

AUDIO INPUT (for INPUT5)

 

 

 

 

Pin jack (×2)

 

 

 

 

L/R ............

500 mVrms/more than 10 kΩ

Accessories

 

Label for remote control unit ...............................

× 1

Connector indicator label .....................................

× 1

Screws (3 × 8) .....................................................

× 2

Operating instructions .........................................

× 1

Warranty ..............................................................

× 1

47

Video Card: PDA-5003/PDA-5004

4.3.2 External Dimensions

(Unit: mm)

7 PDA-5003

262

137.3

148.9

301.5

27.6

7 PDA-5004

262

137.3

148.3

301.5

27.6

48

Video Card: PDA-5003/PDA-5004

<Connection panel: when equipped with PDA-5003>

367.8

17

45

99.3

 

12 12

28

 

38

 

42

 

32.7

37

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

402.8

37

18 21.5 14 22 18 18 18 18 36.5 14

130.2

51

360

98

 

141.9

: Symbol indicates the alignment point.

<Connection panel: when equipped with PDA-5004>

367.8

 

 

17

45

99.3

 

12 12

28

38

42

32.7

39

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

402.8

39

14

26

14

26

14

26

14 14

34

14

130.2

51

360

98

 

141.9

: Symbol indicates the alignment point.

49

Video Card: PDA-5003/PDA-5004

4.3.3 Installing procedures

Installation instructions are listed below. When installing the unit, if a screw or other object should drop inside the Plasma Display, immediately consult your nearest Pioneer Service Center. Continuing operation may damage the panel. This device has been designed for installation on the Pioneer Plasma Display PDP-607CMX. Installation procedures are as follows:

Check the following before installing this video card:

Plasma Display is disconnected from the computer and any other devices.

The Plasma Display is unplugged from the wall outlet before installing/removing a card from a panel slot.

Installation Notes:

Do not install the PDA-5002 on the PDP-607CMX display units.

When opening the protective cover, take care not to drop screws or other objects in the opening. Objects dropped inside the display may cause damage or malfunction.

When installing a video card, if the Plasma Display is laid with its screen side facing down, the work surface should be flat and level. The packing material, a blanket, or other soft material should be spread on the work surface to protect the screen before laying the panel down. Take care to prevent scratches or other damage to the unit from tools or other objects. Never rest the display on a surface in such a way that weight or pressure is placed only on the screen surface.

This video card has been designed for exclusive use with the Pioneer Plasma Display PDP-607CMX. Do not attempt unauthorized modifications or alterations since malfunction or damage may result.

Take care not to modify or damage the card’s internal devices in any way.

Before installation, take precautions to eliminate static electricity on your body. Do not touch the card’s circuitry or devices.

This device has not been designed to be repeatedly removed and reinstalled. Avoid removing the card once it is installed.

When installing the PDA-5003, it may be necessary to adjust the impedance selector switch setting. Confirm this item before installing.

Prior to insertion, use a cloth containing ethanol to clean the PCI bus. Wipe in the direction of the electrodes to remove dirt and dust. Wiping with a dry cloth may cause damage due to static electricity.

Installation

Illustration depicts PDA-5003 model

1 Remove the protective cover over the video card slot on the Plasma Display’s terminal panel.

Protective cover

2Align the video card with the two rails visible inside of the port then gently and evenly insert the card.

rails

Note

Be very careful when inserting the card. Aim the card’s mounting surface oriented toward the rear of the Plasma Display. The card or display may be damaged if the card is inserted crookedly or with excessive force.

Impedance selector switch is found only on the PDA5003.

Device

 

 

 

mounting

 

 

 

surface

Impedance

 

 

 

selector switch

 

 

75 Ω

2.2 kΩ

S-VIDEO INPUT3 VIDEO INPUT4 INPUT 3/4 AUDIO

ANALOG RGB

INPUT5

AUDIO

 

HD (H/V SYNC)

 

 

3 After inserting the video card all the way into the slot, confirm that it is seated securely. The screws removed in step 1 to secure the card in place.

S-VIDEO

INPUT3

VIDEO

INPUT4

INPUT 3/4

AUDIO

ANALOG RGB

INPUT5

AUDIO

HD (H/V SYNC)

50

Video Card: PDA-5003/PDA-5004

4Affix the accessory connector indicator label to the Plasma Display then affix the remote control label to the remote control that is furnished with the Plasma Display.

INPUT3

 

INPUT4

 

AUDIO

 

 

 

INPUT5

 

 

 

 

 

VIDEO

INPUT3/4

 

 

ANALOG RGB

 

 

 

AUDIO

S-VIDEO

 

 

 

 

(ON SYNC)

 

(H/V SYNC)

 

 

 

IN

OUT

R

L

G

B

R

HD

VD

R

L

PDA-5003

RGB (BNC)

PDA-5004

COMPONENT

Note

Use a soft cloth to gently wipe away any dust or soiling

from the surface before affixing the label.

Video Card Removal (Be careful not to insert

and remove it frequently).

1

S-VIDEO

INPUT3

VIDEO

INPUT4

INPUT 3/4

AUDIO

ANALOG RGB

INPUT5

AUDIO

HD (H/V SYNC)

2Holding the inside tabs, pull the video card straight out.

 

Impedance

 

Device

selector switch

mounting

 

 

surface

75 Ω

2.2 kΩ

 

VIDEO INPUT4 INPUT 3/4 AUDIO

ANALOG RGB

 

 

HD (H/V SYNC)

 

51

Video Card: PDA-5003/PDA-5004

4.3.4Input connectors on the Plasma Display with video card

7 When using PDA-5003

Consult the following chart when making connections to a Plasma Display equipped with this video card.

Input

 

 

 

 

 

 

Connector

INPUT INPUT INPUT INPUT INPUT

Connected

1

*1

2

3

4

*1

component

 

5

and signals

 

 

 

 

 

 

AV component

 

 

 

 

 

 

Analog RGB

 

 

 

 

 

 

Component video

 

 

 

 

 

 

S video

 

 

 

 

 

 

Composite video

 

 

 

 

 

 

Digital RGB

 

 

 

 

 

 

Personal computer

 

 

 

 

 

 

(PC)

 

 

 

 

 

 

Analog RGB

 

*2

 

 

 

 

S video

 

 

 

 

*3

 

Composite video

 

 

 

 

 

*3

 

 

 

 

 

 

Digital RGB

 

 

 

*4

 

 

 

 

 

 

 

 

*1 Although INPUT1 and INPUT5 are compatible with various kinds of signals, setup using the on-screen menu is necessary after connections are made in order match the characteristics of the source component.

*2 INPUT1 is compatible with Microsoft’s Plug & Play (VESA DDC 1/2B).

*3 Depending on the video output board of the computer, this type of connection may not be possible.

*4 INPUT2 is compatible with Microsoft’s Plug & Play (VESA DDC 2B).

7 When using PDA-5004

Consult the following chart when making connections to a Plasma Display equipped with this video card.

Input

 

 

 

 

 

Connector

INPUT INPUT INPUT INPUT INPUT

Connected

*1

2

3

4

*1

component

1

5

and signals

 

 

 

 

 

AV component

Analog RGB

Component video

S video

Composite video

Digital RGB

Personal computer (PC)

 

Analog RGB

*2

S video

*3

Composite video

*3

 

Digital RGB

*4

 

*1 Although INPUT1 and INPUT5 are compatible with various kinds of signals, setup using the on-screen menu is necessary after connections are made in order match the characteristics of the source component.

*2 INPUT1 is compatible with Microsoft’s Plug & Play (VESA DDC 1/2B).

*3 Depending on the video output board of the computer, this type of connection may not be possible.

*4 INPUT2 is compatible with Microsoft’s Plug & Play (VESA DDC 2B).

4.3.5 Connection to INPUT1 and INPUT5

7 When using PDA-5003

Various components can be connected to the INPUT1 and INPUT5 jacks. After connections are made, on-screen setup is necessary to match the characteristics of the connected component.

INPUT5

[ON SYNC]

 

 

[H/V SYNC]

 

jack

G

B

R

HD

VD

Output source

 

 

 

 

 

Video component/

 

 

 

 

 

personal

G ON SYNC

B

R

 

 

computer (PC)

 

 

with RGB output

 

 

 

 

 

 

G

B

R

H/V SYNC

 

 

G

B

R

HD

VD

Video component

 

 

 

 

 

with component

Y

PB/CB PR/CR

 

 

video output

 

 

 

 

 

 

 

: Do not connect anything. : Connect to this jack.

Note

Components compatible with INPUT1 are also compatible with INPUT5. When making connections to INPUT1, please refer to the Plasma Display’s Operating Instructions.

7 When using PDA-5004

Various components can be connected to the INPUT1 and INPUT5 jack. After connections are made, on-screen setup is necessary to match the characteristics of the connected component.

INPUT5 jack

Y

PB/CB

PR/CR

Output source

 

 

 

Video component/personal

 

 

 

computer (PC) with RGB

 

 

 

output

G ON SYNC

B

R

 

 

 

 

Video component with

 

 

 

component video output

Y

PB/CB

PR/CR

 

: Connect to this jack.

Note

When making connections to INPUT1, please refer to the Plasma Display’s Operating Instructions.

52

Video Card: PDA-5003/PDA-5004

4.3.6 Connection to INPUT1 or INPUT5

7 When using PDA-5003

Connection to AV components

Connection to AV component equipped with

component video jacks

Make component video connections for AV components equipped with component video jacks.

When connecting to ANALOG RGB IN (INPUT1)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INPUT1

 

 

 

 

 

 

 

 

 

 

 

ANALOG RGB OUT

ANALOG RGB IN

 

 

 

 

 

 

 

 

 

(D-Sub)

 

(D-Sub)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

On-screen setup is necessary after connection.

When connecting to ANALOG RGB (INPUT5)

 

 

ANALOG RGB

INPUT5

G(ON SYNC)

B

R

HD (H/V SYNC) VD

Connect the Y signal to the G jack, the PB/CB signal to the B jack, and the PR/CR signal to the R jack. On-screen setup is necessary after connection.

INPUT5 jacks are all BNC jacks.

If necessary, use commercially available BNC/pin-plug conversion adapters to make connections.

Note

The Plasma Display and this Video Card are designed to support component video signals with standard, stable signal levels and sync signals. As a result, some image disruption may be generated during use of various special trick play functions on video components.

7 When using PDA-5004

Connection to AV components

Connection to AV component equipped with

component video jacks

Make component video connections for AV components equipped with component video jacks.

When connecting to ANALOG RGB IN (INPUT1)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INPUT1

 

 

 

 

 

 

 

 

 

 

 

ANALOG RGB OUT

ANALOG RGB IN

 

 

 

 

 

 

 

 

 

(D-Sub)

 

(D-Sub)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

On-screen setup is necessary after connection.

When connecting to COMPONENT VIDEO (INPUT5)

COMPONENT

INPUT5

VIDEO

 

Y Pb/Cb Pr/Cr

Connect the Y signal to the Y jack, the PB/CB signal to the PB/CB jack, and the PR/CR signal to the PR/CR jack.

Note

The Plasma Display and this Video Card are designed to support component video signals with standard, stable signal levels and sync signals. As a result, some image disruption may be generated during use of various special trick play functions on video components.

53

Video Card: PDA-5003/PDA-5004

Connection of G ON SYNC analog RGB source

Make G ON SYNC connections for a component with output that has the synchronization signal layered on top of the green signal.

When connecting to ANALOG RGB IN (INPUT1)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INPUT1

 

 

 

 

 

 

 

 

 

 

 

ANALOG RGB OUT

ANALOG RGB IN

 

 

 

 

 

 

 

 

 

(D-Sub)

 

(D-Sub)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

On-screen setup is necessary after connection.

When connecting to ANALOG RGB (INPUT5)

[Connections for PDA-5003]

 

 

ANALOG RGB

INPUT5

G(ON SYNC)

B

R

HD (H/V SYNC) VD

On-screen setup is necessary after connection.

Note

When making G ON SYNC connections, do not make any connections to the VD or HD jacks. If connections are made, the picture may be not displayed normally.

When connecting to COMPONENT VIDEO (INPUT5)

[Connections for PDA-5004]

COMPONENT

INPUT5

VIDEO

 

Y Pb/Cb Pr/Cr

Connect the G ON SYNC signal to the Y jack, the B signal to the PB/CB jack, and the R signal to the PR/CR jack.

On-screen setup is necessary after connection.

54

Video Card: PDA-5003/PDA-5004

Connection of composite SYNC analog RGB

source

Make composite SYNC connections for a component with output that has the vertical synchronization signal layered on top of the horizontal synchronization signal.

When connecting to ANALOG RGB IN (INPUT1)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INPUT1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ANALOG RGB OUT

ANALOG RGB IN

 

 

 

 

 

 

 

 

 

 

 

 

(D-Sub)

 

(D-Sub)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

On-screen setup is necessary after connection.

When connecting to ANALOG RGB (INPUT5)

[Connections for PDA-5003]

 

 

ANALOG RGB

INPUT5

G(ON SYNC)

B

R

HD (H/V SYNC) VD

When using INPUT5, set the impedance selector switch to match the output impedance of the connected component’s synchronization signal.

When the output impedance of the sync signal is below 75 Ω remove the video card and set the impedance selector switch to 75 Ω.

On-screen setup is necessary after connection.

Note

When making composite SYNC connections, do not connect anything to the VD jack. If connected to, the picture may not be displayed properly.

Connection to a personal computer

Connection method differs depending on the computer type. When connecting, please thoroughly read the computer’s operating instructions.

Before making connections, be sure to make sure that the personal computer’s power and display’s main power is off.

For the PC input signals and screen sizes that the display is compatible with, please refer to the Plasma Display’s Operating Instructions.

Connection of separate SYNC analog RGB

source

Make separate SYNC connections for a personal computer that has RGB output separated into 5 output signals: green, blue, red, horizontal synchronization signal, and vertical synchronization signal.

When connecting to ANALOG RGB (INPUT5)

[Connections for PDA-5003]

 

 

ANALOG RGB

INPUT5

G(ON SYNC)

B

R

HD (H/V SYNC) VD

When using INPUT5, set the impedance selector switch to match the output impedance of the connected computer’s synchronization signal.

When the output impedance of the sync signal is below 75 Ω remove the video card and set the impedance selector switch to 75 Ω.

On-screen setup is necessary after connection.

55

Video Card: PDA-5003/PDA-5004

When connecting to ANALOG RGB IN (INPUT1)

 

 

 

 

 

 

 

 

 

 

INPUT1

 

 

 

ANALOG RGB OUT

ANALOG RGB IN

 

(D-Sub)

 

(D-Sub)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Connection of G ON SYNC analog RGB source

Make G ON SYNC connections for a personal computer with output that has the synchronization signal layered on top of the green signal.

When connecting to ANALOG RGB IN (INPUT1)

 

 

 

 

 

 

 

 

INPUT1

 

ANALOG RGB OUT

ANALOG RGB IN

(D-Sub)

 

(D-Sub)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Connect the cable corresponding to the shape of the input terminal on the display and the personal computer’s output terminal.

Secure by tightening the terminal screws on both units.

On-screen setup is necessary after connection.

Note

Depending on the type of computer model being connected, a conversion connector or adapter etc. provided with the computer or sold separately may be necessary.

For details, please read your PC’s instruction manual or consult the maker or nearest dealer of your computer.

When connecting to ANALOG RGB OUT (INPUT1)

 

 

 

 

 

 

 

 

 

 

INPUT1

 

ANALOG RGB OUT

ANALOG RGB IN

(D-Sub)

 

(D-Sub)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

To an external monitor

With the Plasma Display, it is possible to output the video signal to an external monitor or other component from the ANALOG RGB OUT (INPUT1) terminal.

Note

A video signal will not be output from the ANALOG RGB OUT (INPUT1) terminal when the main power of this unit is off or in standby.

On-screen setup is necessary after connection.

When connecting to ANALOG RGB (INPUT5)

[Connections for PDA-5003]

 

 

ANALOG RGB

INPUT5

G(ON SYNC)

B

R

HD (H/V SYNC) VD

On-screen setup is necessary after connection.

Note

When making G ON SYNC connections, do not make any connections to the VD or HD jacks. If connections are made, the picture may be not displayed normally.

56

Video Card: PDA-5003/PDA-5004

When connecting to COMPONENT VIDEO (INPUT5)

[Connections for PDA-5004]

COMPONENT

INPUT5

VIDEO

 

Y Pb/Cb Pr/Cr

When connecting to ANALOG RGB (INPUT5)

[Connections for PDA-5003]

 

 

ANALOG RGB

INPUT5

G(ON SYNC)

B

R

HD (H/V SYNC) VD

On-screen setup is necessary after connection.

Connection of composite SYNC analog RGB

source

Make composite SYNC connections for a personal computer with output that has the vertical synchronization signal layered on top of the horizontal synchronization signal.

When connecting to ANALOG RGB IN (INPUT1)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INPUT1

 

 

 

 

 

 

 

 

 

 

ANALOG RGB OUT

ANALOG RGB IN

 

 

 

 

 

 

 

 

(D-Sub)

 

(D-Sub)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

On-screen setup is necessary after connection.

When using INPUT5, set the impedance selector switch to match the output impedance of the connected computer’s synchronization signal.

When the output impedance of the sync signal is below 75 Ω remove the video card and set the impedance selector switch to 75 Ω.

On-screen setup is necessary after connection.

Notes

÷When making composite SYNC connections, do not connect anything to the VD jack. If connected to, the picture may not be displayed properly.

÷Some types of computer devices manufactured by Apple Computer, Inc. are equipped with both G ON SYNC and composite SYNC outputs. This type of component should be connected using the G ON SYNC connection.

57

Video Card: PDA-5003/PDA-5004

4.3.7 Connection to INPUT2

A computer equipped with DVI output (digital RGB signal) or an AV component equipped with DVI output, can be connected to the Plasma Display’s DVI connector.

INPUT2

DIGITAL RGB (DVI-D)

4.3.9 Connection to INPUT4

Connect an AV component that has a video output jack to the video card’s INPUT4 jack. The VIDEO OUT (INPUT4) jack can be used to output the video signal to a separate monitor, recording device or other component with video input capability.

Note

A video signal will not be output from the VIDEO OUT (INPUT4) jack when the main power of this display is off or in standby mode.

[When using PDA-5003]

VIDEO INPUT4

IN OUT

Computer or AV component

On-screen setup is necessary after connection.

Note

Use a DVI-D 24-pin (digital only) cable for the connection.

NOTICE

INPUT2 is compatible with Microsoft’s Plug & Play (VESA DDC 2B).

For screen sizes and input signals compatible with INPUT2, please refer to the Plasma Display’s Operation Instructions.

4.3.8 Connection to INPUT3

Connect an AV component that has S-video output jack to the video card’s S-VIDEO (INPUT3) jack.

S-VIDEO INPUT3

AV component

To a monitor or a recording device

AV component

[When using PDA-5004]

VIDEO

INPUT4

IN OUT

To a monitor or a recording device

AV component

Signals to the INPUT3 and INPUT4 jacks are all compatible with the following TV systems: NTSC, PAL, SECAM, 4.43NTSC, PAL M and PAL N.

58

Video Card: PDA-5003/PDA-5004

4.3.10 About DTV set top box connection

To ensure proper connection, please carefully read the instruction manual supplied with the DTV set top box.

The set top box output signals that this display is compatible with are as follows.

Video

Video signal

Video

Jacks where connection is possible

 

signal type

signal format

INPUT1 INPUT2 INPUT3 INPUT4 INPUT5

 

HDTV

1125i (1080i)

Component

 

750p (720p)

 

 

RGB

 

 

 

 

SDTV

525i (480i)

Composite

 

 

625i (575i)

S Video

 

 

 

 

 

 

Component

 

 

 

RGB

 

 

525p (480p)

Component

 

 

625p (575p)

RGB

 

 

 

 

59

Video Card: PDA-5003/PDA-5004

4.3.11 Audio connections

Before making connections, be sure to check that the audio component’s power and the display’s main power is off.

Connect an audio component to the audio input jack of the Plasma Display with installed video card.

When the video card is installed, the Plasma Display provides four or five audio input jacks and one audio output jack. Consult the following chart to choose the proper audio input for each video input.

Video

Audio input

Sound output

input

 

 

 

INPUT1

Stereo mini jack (L/R)

Sound of the selected

INPUT2

Stereo mini jack (L/R)

video input is output from

 

 

 

the

INPUT5

Pin jacks (L/R)

 

 

 

• SPEAKER (L/R) terminals

INPUT3

Pin jacks (L/R) *1

 

 

 

• Stereo mini jack (L/R).

INPUT4

Pin jacks (L/R)

*1

 

 

 

 

 

 

*1 When using the PDA-5003, the INPUT3 and INPUT4 audio input connectors are shared.

Audio connection for component connected to INPUT1

OUTPUT INPUT1 INPUT2

AUDIO AUDIO AUDIO

Audio connections for component connected to INPUT2

OUTPUT INPUT1 INPUT2

AUDIO AUDIO AUDIO

A stereo miniplug cable can be used to connect the audio output from the component connected to INPUT2, to the Plasma Display’s AUDIO (INPUT2) jack (L/R).

Sound is output from both the AUDIO (OUTPUT) stereo mini jack (L/R) and the SPEAKER (L/R) terminals according to the video input selection.

Audio connection for component connected to INPUT5

INPUT5

AUDIO

R L

A stereo miniplug cable can be used to connect the audio output from the component connected to INPUT1, to the Plasma Display’s AUDIO (INPUT1) jack (L/R).

Sound is output from both the AUDIO (OUTPUT) stereo mini jack (L/R) and the SPEAKER (L/R) terminals according to the video input selection.

The audio line for the component connected to INPUT5 can be connected to the AUDIO R/L (INPUT5) pin jacks.

Sound is output from both the AUDIO (OUTPUT) stereo mini jack (L/R) and the SPEAKER (L/R) terminals according to the video input selection.

60

Video Card: PDA-5003/PDA-5004

[When using PDA-5003]

Audio connection for component connected to INPUT3 or INPUT4

INPUT 3/4

AUDIO

R L

Audio input to the AUDIO R/L (INPUT3/4) pin jacks is possible for a component connected to either INPUT3 or INPUT4.

Sound is output from both the AUDIO (OUTPUT) stereo mini jack (L/R) and the SPEAKER (L/R) terminals according to the video input selection.

[When using PDA-5004]

Audio connection for component connected to INPUT3

INPUT3

AUDIO

R L

The audio line for the component connected to INPUT3 can be connected to the AUDIO R/L (INPUT3) pin jacks.

Sound is output from both the AUDIO (OUTPUT) stereo mini jack (L/R) and the SPEAKER (L/R) terminals according to the video input selection.

Audio connection for component connected to INPUT4

INPUT4

AUDIO

R L

The audio line for the component connected to INPUT4 can be connected to the AUDIO R/L (INPUT4) pin jacks.

Sound is output from both the AUDIO (OUTPUT) stereo mini jack (L/R) and the SPEAKER (L/R) terminals according to the video input selection.

61

Video Card: PDA-5003/PDA-5004

INPUT Response Signals

INPUT 1, 5

7Video signals supported (applies only when equipped with PDA-5003/PDA-5004)

Vertical

Horizontal

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Frequency

Frequency

 

Signal Format

Remark

Fv (Hz)

Fh (kHz)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

15.625

 

 

Component

625i(576i)/SDTV

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RGB

 

 

 

 

 

 

 

 

 

28.13

 

 

Component

1125i(1080i)/HDTV

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RGB

 

 

 

 

 

 

 

 

 

31.25

 

 

Component

625p(576p)/SDTV

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

50

 

 

 

 

 

RGB

 

 

 

 

 

 

 

37.50

 

 

Component

750p(720p)/HDTV

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RGB

 

 

 

 

 

 

 

 

 

56.20

 

 

Component

1125p(1080p)/HDTV

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RGB

 

 

 

 

 

 

 

 

 

62.50

 

 

Component

520i(480i)/SDTV

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RGB

 

 

 

 

 

 

 

 

 

15.734

 

 

Component

525i(480i)/SDTV

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RGB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

31.5

 

 

Component

525p(480p)/SDTV

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RGB

 

 

 

 

 

 

 

 

60

33.75

 

 

Component

1125i(1080i)/HDTV

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RGB

1125i(1035i)/HDTV

 

 

 

 

 

 

 

 

45.0

 

 

Component

750p(720p)/HDTV

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RGB

 

 

 

 

 

 

 

 

 

67.5

 

 

Component

1125p(1080p)/HDTV

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RGB

 

 

 

 

 

 

 

 

7 PC signals supported

Resolution

Refresh rate

Remark

(Dot x Line)

Vertical

Horizontal

 

 

 

 

 

 

 

640x400

70.1 Hz

31.5 kHz

NEC PC-9800

720x400

70.1 Hz

31.5 kHz

NEC PC-9800

 

85.1 Hz

37.9 kHz

 

640x480

59.9 Hz

31.5 kHz

 

 

66.7 Hz

35.0 kHz

Apple Macintosh 13”

 

72.8 Hz

37.9 kHz

 

 

75 Hz

37.5 kHz

 

 

85 Hz

43.3 kHz

 

 

100.4 Hz

51.1 kHz

I/O DATA

 

120.4 Hz

61.3 kHz

I/O DATA

848x480

60 Hz

31.0 kHz

 

852x480

60 Hz

31.7 kHz

 

800x600

56.3 Hz

35.2 kHz

 

 

60.3 Hz

37.9 kHz

 

 

72.2 Hz

48.1 kHz

 

 

75 Hz

46.9 kHz

 

 

85.1 Hz

53.7 kHz

 

 

99.8 Hz

63.0 kHz

I/O DATA

 

120 Hz

75.7 kHz

I/O DATA

832x624

74.6 Hz

49.7 kHz

Apple Macintosh 16”

1024x768

60 Hz

48.4 kHz

 

 

60 Hz

49.7 kHz

Work station (SGI)

 

70.1 Hz

56.5 kHz

 

 

75 Hz

60.0 kHz

( ) indicates Apple

 

(74.9 Hz )

(60.2 kHz)

Macintosh 19

 

85 Hz

68.7 kHz

 

 

100.6 Hz

80.5 kHz

I/O DATA

 

119.4 Hz

95.5 kHz

 

1280x768

56.2 Hz

45.1 kHz

 

 

59.8 Hz

48 kHz

 

 

69.8 Hz

56 kHz

 

1360x765

60 Hz

47.7 kHz

 

1360x768

60 Hz

47.7 kHz

I/O DATA

1376x768

59.9 Hz

48.3 kHz

I/O DATA

1280x800

59.8 Hz

49.7 kHz

CVT

1280x854

60 Hz

53.1 kHz

PC

1152x864

60 Hz

53.7 kHz

 

 

72 Hz

64.9 kHz

 

 

75 Hz

67.5 kHz

 

1152x870

75.1 Hz

68.7 kHz

Apple Macintosh 21”

1152x900

66 Hz

61.8 kHz

Sun Microsystems LO

 

76 Hz

71.7 kHz

Sun Microsystems HI

1440x900

59.9 Hz

55.9 kHz

Apple Macintosh 17”

1280x960

60 Hz

60.0 kHz

 

 

85 Hz

85.9 kHz

 

1280x1024

60 Hz

63.9 kHz

Work station (SGI)

 

60 Hz

64.0 kHz

 

 

60 Hz

64.6 kHz

Work station (EWS4800)

 

71.2 Hz

75.1 kHz

Work station (EWS4800)

 

72 Hz

78.1 kHz

Work station (HP)

 

75 Hz

80.0 kHz

 

 

76.1 Hz

81.1 kHz

Work station (SUN)

 

85 Hz

91.1 kHz

 

 

100.1 Hz

108.5 kHz

I/O DATA

1400x1050

60 Hz

65.3 kHz

 

 

74.9 Hz

82.3 kHz

 

 

85 Hz

93.9 kHz

 

1680x1050

60 Hz

65.3 kHz

 

1600x1200

60 Hz

75.0 kHz

 

 

65 Hz

81.3 kHz

 

 

70 Hz

87.5 kHz

 

 

75 Hz

93.8 kHz

 

 

85 Hz

106.3 kH z

 

1920x1200

59.9 Hz

74.6 kHz

CVT

1920x1200RB

60 Hz

74.0 kHz

CVT

62

Video Card: PDA-5003/PDA-5004

INPUT 2

7Video signals supported (applies only when equipped with PDA-5003/PDA-5004)

Vertical

Horizontal

Signal

Remark

Frequency

Frequency

Format

Fv (Hz)

Fh (kHz)

 

 

 

 

 

 

 

 

 

 

 

 

28.13

RGB

1125i(1080i)/HDTV

50

31.25

RGB

625p(576p)x720 dot/SDTV

 

37.50

RGB

750p(720p)/HDTV

 

31.5

RGB

525p(480p)x720 dot/SDTV

60

33.75

RGB

1125i(1080i)/HDTV

 

45.0

RGB

750p(720p)/HDTV

The following signals are not formally supported, but can be displayed (They are not recorded in EDID data).

Vertical

Horizontal

Signal

Remark

Frequency

Frequency

Format

Fv (Hz)

Fh (kHz)

 

 

 

 

 

 

 

 

 

 

 

50

15.6

RGB

625i(576i)/SDTV

56.25

RGB

1125p(1080p)/HDTV

 

 

 

 

 

 

15.8

RGB

525i(480i)/SDTV

60

31.5

RGB

525p(480p)x640 dot/SDTV

 

67.5

RGB

1125p(1080p)/HDTV

50

62.5

RGB

1250p/HDTV

*They may not be displayed normally depending on the connected device.

7 PC signals supported

Resolution

Refresh rate

Remarks

(Dot x Line)

Vertical

Horizontal

 

 

 

 

 

 

 

640x480

59.9 Hz

31.5 kHz

 

 

72.8 Hz

37.9 kHz

 

 

75 Hz

37.5 kHz

 

 

85 Hz

43.3 kHz

 

 

100.4 Hz

51.1 kHz

 

 

120.4 Hz

61.3 kHz

 

720x400

70.1 Hz

31.5 kHz

NEC PC-9800

 

85.1 Hz

37.9 kHz

 

848x480

60 Hz

31.0 kHz

 

852x480

60 Hz

31.7 kHz

 

800x600

56.3 Hz

35.2 kHz

 

 

60.3 Hz

37.9 kHz

 

 

72.2 Hz

48.1 kHz

 

 

75 Hz

46.9 kHz

 

 

85.1 Hz

53.7 kHz

 

 

99.8 Hz

63.0 kHz

 

 

120 Hz

75.7 kHz

 

1024x768

60 Hz

48.4 kHz

 

 

60 Hz

49.7 kHz

Work station (SGI)

 

70.1 Hz

56.5 kHz

 

 

75 Hz

60.0 kHz

 

 

85 Hz

68.7 kHz

 

 

100.6 Hz

80.5 kHz

 

 

119.4 Hz

95.5 kHz

 

1280x768

56.2 Hz

45.1 kHz

 

 

59.8 Hz

48 kHz

 

 

69.8 Hz

56 kHz

 

1280x800

59.8 Hz

49.7 kHz

 

1280x854

60 Hz

53.1 kHz

 

1360x768

60 Hz

47.7 kHz

I/O DATA

1376x768

59.9 Hz

48.3 kHz

I/O DATA

1152x864

60 Hz

53.7 kHz

 

 

72 Hz

64.9 kHz

 

 

75 Hz

67.5 kHz

 

1152x900

66 Hz

61.8 kHz

Sun Microsystems LO

 

76 Hz

71.7 kHz

Sun Microsystems HI

1440x900

59.9 Hz

55.9 kHz

Apple Macintosh17“

1280x960

60 Hz

60.0 kHz

 

 

85 Hz

85.9 kHz

 

 

60 Hz

63.9 kHz

Work station (SGI)

1280x1024

60 Hz

64.0 kHz

 

 

60 Hz

64.6 kHz

Work station (EWS4800)

 

71.2 Hz

75.1 kHz

Work station (EWS4800)

 

72 Hz

78.1 kHz

Work station (HP)

 

75 Hz

80.0 kHz

 

 

76.1 Hz

81.1 kHz

Work station (SUN)

 

85 Hz

91.1 kHz

 

1400x1050

60 Hz

65.3 kHz

 

 

74.9 Hz

82.3 kHz

 

1680x1050

60 Hz

65.3 kHz

 

1920x1080

50 Hz

56.2 kHz

 

 

60 Hz

67.5 kHz

 

1600x1200

60 Hz

75.0 kHz

 

1920x1200RB

60 Hz

74.0 kHz

CVT

INPUT 3

(applies only when equipped with PDA-5003/PDA-5004):

Y/C Separate video signal NTSC, PAL, SECAM, 4.43 NTSC, PAL

M, PAL N

INPUT 4

(applies only when equipped with PDA-5003/PDA-5004):

Composite video signal NTSC, PAL, SECAM, 4.43 NTSC, PAL

M, PAL N

63

Table Top Stand: PDK-TS26

4.4 Table Top Stand: PDK-TS26

4.4.1 Specifications

External dimensions .................

1125 mm (W) × 205 mm (H) × 430 mm (D)

 

(44-9/32 in. (W) × 8-1/16 in. (H) × 16-15/16 in. (D))

Weight .......................................

6.5 kg (14.3 lbs.) (mounting hardware only)

 

68.5 kg (151.0 lbs.) (mounting hardware and Plasma Display <PDP-607CMX>)

Materials ....................................

Base: Aluminum; Cover: plastic (ABS); Stand stay: Zinc

Finish ..........................................

Cover: paint (Pioneer original color)

Package dimensions .................

1080 mm (W) × 257 mm (H) × 204 mm (D)

 

(42-17/32 in. (W) × 10-1/8 in. (H) × 8-1/32 in. (D))

Package weight .........................

8.5 kg (18.7 lbs.)

Layers of packing ......................

6 layers

Accessories

 

Feets ............................................................................

× 2

Bar ................................................................................

× 1

Stand assembly screws (M4 × 10 mm) .......................

× 8

Monitor attachment screws (M6 × 50 mm) .................

× 4

Securing brackets (eye screw) .....................................

× 2

Operating Temperature Restrictions

Ambient Temperature: 0 °C to 40 °C

Operating temperature restrictions for when the speaker system (PDP-S55-LR) is attached.

Ambient temperature: 0 °C to 40 °C

Other factors

Maintain sufficient clearance between the display and the wall (at least 100 mm)

64

Table Top Stand: PDK-TS26

4.4.2 Installation coordinates for screws used to attach the stand to a surface

*To stabilize the equipment on the floor, use screws that have a nominal diameter of 6 mm to 8 mm (1/4 inch to 5/16 inch) and that are at least 25 mm (31/32 inch) long.

Unit: mm (inch)

(16-15/16)

164.5

(6-15/32)

 

 

430

 

 

 

 

 

46.5

27/32)-

253.5

 

(9-31/32)

 

 

 

 

 

(1

 

 

 

 

 

18 mm

23/32 inch)

 

 

 

12 mm to

(15/32 inch to

963 (37-29/32)

16

(5/8)

 

mm8tomm6

inch)5/16toinch(1/4

To stabilize the equipment on

 

 

 

 

 

 

the floor, use screws that have

 

 

 

a nominal diameter of 6 mm to

 

 

 

8 mm (1/4 inch to 5/16 inch)

Min. 25 mm

 

 

and that are at least 25 mm

(31/32 inch)

 

 

(31/32 inch) long.

4.4.3 External Dimensions

7 When using Plasma Display

Unit: mm (inch)

1470 (57-7/8)

880 (34-21/32)

(19-23/32)

of the display]

941 (37-1/16)

 

501

[Cente

197 (7-3/4)

 

1125 (44-9/32)

 

430 (16-15/16)

65

Table Top Stand: PDK-TS26

4.4.4 Stand assembling

1Remove the cardboard and accessories (screws, operating instructions) from the box.

4Tear off the protective sheets covering the feet from their perforated lines so you can see their attachments.

¶ View of packaged items

Cardboard

Place them so the attachments are towards you.

 

 

Shock absorbing

 

Shock

boxes

Attachment

absorbing boxes

 

Screws / Securing

 

 

 

 

brackets

Perforated line

 

 

 

Operating instructions

 

Bar

Toward you

 

(Covered with

 

 

 

protective sheets)

 

 

Feet

 

 

(Covered with protective sheets)

 

2Remove the bar then remove the shock absorbing boxes from the left and right sides.

5Take the protective sheet off the bar that you removed in step 2, insert the bar aligned with the guide pins of the feet.

If the bar and guide pins on the feet do not match, the feet and bar are in reversed position. Reverse the left and right ends of the bar and align it with the pins again.

Then tighten it with the included stand assembly screws (M4 × 10 mm).

Guide pins

3Remove the two boxes containing the feet, and set them upside down on the floor.

Caution

Tighten the screws firmly. The stand may fall over causing injuries.

6Pick up the boxes containing the feet, turn them over again, and put them back on the floor. Then take the box out of its stand.

66

Table Top Stand: PDK-TS26

4.4.5 Attaching the Stand to the Plasma Display

1Attaching Plasma Display to stand.

Make sure that the stand and Plasma Display are properly aligned together, and then place the Plasma Display onto the stand.

Lift up both ends of the Plasma Display then engage the holes on the bottom of the display with the stand.

2 Fixing Plasma Display to stand.

1.While pulling the upper part of the Plasma Display towards your body,

screw the monitor attachment screws

2-2

(M6 × 50 mm) firmly into place (four locations).

2.Once the Plasma Display has been attached, rock the

monitor gently to make sure that there

is no looseness and that the screws have been screwed tightly into place.

Monitor attachment screws

2-1

Caution

Once the Plasma Display has been placed onto the stand, immediately insert the screws and tighten them to fix the monitor into place. Failing to tighten the screws could result in the monitor falling over, which might in turn result in bodily injury.

Because the Plasma Display is heavy and has a high center of gravity, installation by one or two people is hazardous. Please employ three or more people during installation, being sure to hold the handle on the back as well as the lower portion of the monitor, while supporting its top and bottom.

After attachment, take measures to prevent it from falling over.

Attach the securing brackets and screws provided with the stand to the Plasma Display in the locations

indicated in the accompanying diagram, and then use

Securing brackets

separate commercially available screws (eye screw)

 

and wires or some other similar item of sufficient

 

strength to secure the Plasma Display into place

 

against a wall, pillar, or some other surface or

 

otherwise use the holes located at the rear of the

 

stand to fix the stand into place. (Note that these

 

brackets and screws are not used when using a

 

separately sold ceiling attachment unit or wall

 

attachment unit.)

 

Be sure to take care of the securing wires when

 

moving the stand or Plasma Display.

 

Note that the wires and screws needed to secure the

 

Plasma Display against a wall or pillar or against the

 

stand are not provided with the stand, and that the

 

proper items must be purchased separately in

 

accordance with the type of object or surface against

 

which the monitor is to be secured.

 

Separately purchased screws

67

Wall Mount Unit: PDK-WM03

4.5 Wall Mount Unit: PDK-WM03

4.5.1 Specifications

External dimensions ......................

950 mm (W) × 613 mm (H) × 45 mm (D)

 

(37-13/32 in. (W) × 24-1/8 in. (H) × 1-25/32 in. (D))

Weight ............................................

12.0 kg (26.5 lbs) [mounting hardware only]

 

74.0 kg (163 lbs) [mounting hardware and plasma display]

Finish ...............................................

Semi-matte black paint on rear

Dimensions of packaging ..............

986 mm (W) × 112 mm (H) × 730 mm (D)

 

(38-13/16 in. (W) × 4-13/32 in. (H) × 28-3/4 in. (D))

Package weight ..............................

15 kg (33.1 lbs)

Layers of packing ...........................

12 layers

Components

 

Hung on wall unit ................................................

× 1

Display metal fittings (Right/Left) ........................

× 2

Brackets ..............................................................

× 2

Screws (M5) ........................................................

× 2

Screws (M8) ........................................................

× 6

Operating Temperature Restrictions

Ambient temperature: 0 °C to 40 °C

Operating temperature restrictions for when the speaker system (PDP-S55-LR) is attached.

Ambient temperature: 0 °C to 40 °C

Attachment Restrictions

Install it on perpendicular walls, columns, etc. It cannot be installed on an inclined surface.

In wall-mounting installation allow adequate space (a clearance of 300 mm or more) above and below the monitor set,

as well as on the right and the left.

68

Wall Mount Unit: PDK-WM03

4.5.2 External Dimensions

Unit: mm (inch)

1470 (57-7/8)

 

950 (37-13/32)

 

850 (33-15/32)

 

530 (20-7/8)

 

14-10x20

Center of

 

(14-13/32x25/32)

the display

2-ø8.5 (2-ø11/32)

(19/32)15

 

[Set screw position]

3/4)-

200(7-7/8)

187(7-3/8)

 

 

Center of

 

 

the display

(15

 

 

400

 

2-8.5x12

 

 

 

 

(2-11/32x15/32)

 

 

[Set screw position]

81.5 (3-7/32)

 

 

122

45

(4-13/16)

(1-25/32)

(19-11/16)

296 (11-21/32)

309 (12-5/32)

(34-21/32)

500

295 (11-5/8)

304 (11-31/32)

880

69

Wall Mount Unit: PDK-WM03

4.5.3 Hardware assembly and Plasma Display attachment

1) Attaching the metal fittings

The display comes with left side hardware and right side hardware. Do the installation so that the two eyebolts are both on the inside.

É” 9

 

1 Align the screw holes (ø9) at the positions on the

 

drawing above and below the display metal fittings (one

Eyebolt

each on the left and right side) with the screw holes

 

(M8) on the back surface of the Plasma Display to

 

anchor the two attached M8 screws.

Note

When using the optional stand PDK-TS26, you can attach the display metal fitting with the stand installed.

When doing this, before attaching the display metal fitting, remove the four M6 screws that anchor the Right display to the stand. Make sure that when you lift the Plasma Display, you do not also lift the stand with it. If the stand is displaced, it may cause injuries or be

damaged.

Left

2) Installing the hung on wall unit on the wall

Fix it in position with off-the-shelf anchors or with six M8 screws.

 

Unit: mm (inch)

 

 

 

 

 

950 (37-13/32)

 

494.5(19-15/32)

400(15-3/4)

187(7-3/8)

Center of

591(23-9/32)

 

 

 

 

 

 

 

the display

 

 

 

 

850 (33-15/32)

 

Note

Be sure to attach the anchors or screws to locations of wall beams.

70

Wall Mount Unit: PDK-WM03

3) Installing the Plasma Display

With the display metal fitting already attached to the Plasma Display, attach the plasma display to the hung on wall unit.

1Hang the top hooks of the left and right display metal fittings on the groove in the hung on wall unit.

Top hook

2With the top hooks in the groove, lift the Plasma Display straight up for about 1 cm, and when you cannot raise it any further,

push the bottom edge of the Plasma Display to the wall and hang it with the bottom hooks.

Bottom hook

2 Tighten the anchor screws on the top of the left and right display metal fitting with a driver.

Note

To install it at a high location where you cannot lift it manually, you can install it by suspending the eyebolts on the top hardware of the display with a crane etc.. When doing this, make sure that the eyebolt is not loose.

Note

If the bottom of the Plasma Display does not move when you try to pull it towards you, it is correctly installed.

Anchor screw

71

Speaker System: PDP-S55-LR

4.6 Speaker System: PDP-S55-LR

4.6.1 Specifications

External dimensions .................

90 mm (W) × 880 mm (H) × 96 mm (D) (Not including attachment plates; Qty: 1)

 

(3-17/32 in. (W) × 34-21/32 in. (H) × 3-25/32 in. (D))

 

When mounted to the Plasma Display <PDP-607CMX>:

 

1651 mm (W) × 880 mm (H) × 122 mm (D)

 

(65 in. (W) × 34-21/32 in. (H) × 4-13/16 in. (D))

Weight .......................................

6.8 kg (15 lbs.)

 

68.8 kg (151.7 lbs.) (when mounted to the Plasma Display <PDP-607CMX>)

Dimensions of packaging .........

950 mm (W) × 295 mm (H) × 390 mm (D)

 

(37-13/32 in. (W) × 11-5/8 in. (H) × 15-11/32 in. (D))

Package weight .........................

10.3 kg (22.7 lbs.)

Layers of packing ......................

10 layers

Model .........................................

2-way, 3-speaker system (bass-reflection mode)

Woofer (for low tones) .......

8 cm cone type x2

Tweeter (for high tones) ....

5 cm cone type x1

Nominal impedance .................

6 Ω

Frequency Range ......................

60 Hz to 35 000 Hz

Sensitivity ..................................

85 dB/W (at 1 m distance)

Permissible input:

 

Max. input ............................

60 W

Rated input ..........................

20 W

Accessory parts (for two speakers)

Cushions .............................................................

× 2

Speaker cords .....................................................

× 2

Attachment pieces ..............................................

× 4

Cord clampers .....................................................

× 2

Screws (M5) ......................................................

× 12

Operating instructions .........................................

× 1

Cautions

The sound may be irregular if there is a CRT type PC monitor close to the speakers. To prevent this, keep speakers separated from the PC if you are using a CRT monitor.

72

Speaker System: PDP-S55-LR

4.6.2 External Dimensions (when mounted to the Plasma Display)

Unit: mm (inch)

*1: Dimension from the front surface of the speaker to the attachment pieces. *2: Size of Plasma Display

39 (1-17/32)

 

 

99 (3-29/32)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

96 (3-25/32)

119 (4-11/16) *1

 

1651 (65)

 

90 (3-17/32)

90 (3-17/32)

122 (4-13/16) *2

880 (34-21/32)

(4-11/16)

(6-21/32)

119

169

 

 

235 (9-1/4)

65 (2-9/16)

169 (6-21/32)

181 (7-1/8)

 

73

Speaker System: PDP-S55-LR

4.6.3 Installation on the Plasma Display

1) Installation procedure

Install the speaker system according to the steps 1 through 5.

Note:

The speakers are divided into a right (R) and left (L) speaker. When attaching the speakers, be sure to check to labels (R/L) located on the rear of the speakers.

1 Remove the seals from the cushions and then attach the cushions to the sides of the speakers in the locations indicated in the diagram below.

Cushions

3 Loosely screwing the screws (M5) into place on the top attachment pieces (two locations).

Note:

To install the Plasma Display on a wall, first attach the attachment pieces to the Plasma Display then install it on the wall. After installing the Plasma Display on the wall, it may be impossible to tighten the screws on the attachment pieces.

2Attaching the attachment pieces to the locations shown in the drawing of the Plasma Display with screws (M5) (eight locations).

Check the marks on the attachment pieces (TL, TR, BL, BR) and the Plasma Display attachment locations.

4 Attaching the screws (M5) that have been loosely screwed into place on the hooks on top of the speakers. Loosely screw the screws (M5) into place with the screw holes on the attachment pieces on the bottom aligned with the holes in the hooks on the bottom of the speakers.

74

Speaker System: PDP-S55-LR

5Tighten the screws just inserted firmly into place (four locations).

Tighten the screws while pushing the speakers lightly against the Plasma Display. Check to be sure that all four screws have been screwed firmly into place.

If there is a large gap between the Plasma Display and the speakers, adjust them after slightly loosening the screws that were tightened in step 2. After adjustment, re-tighten the screws.

To install the Plasma Display on a wall, it is recommended that you first remove the speaker units, then after the Plasma Display has been installed on the wall, re-attach the speaker units to the Plasma Display.

2) Connect the cords

(Turn off the power of all connected units before connecting the cords.)

Use the provided speaker cords to connect the R/L speaker jacks of the monitor to the speaker jacks of the speakers.

Once the cords have been connected, pull on the cords lightly to make sure that they have been connected firmly to the speaker jacks. An improper connection might result in the sound being interrupted or the appearance of noise in the output sound.

Cord clampers Remove the seal from the rear of the cord

clampers, attach the clampers in the desired position, and clamp the cords into place.

Warning

Never hold the speakers when speakers are attached to the monitor to move the monitor. Doing so might result in the monitor falling, and this in turn might result in bodily injury.

Firmly tighten the screws. The speakers may fall causing injuries.

Note that the speaker cords have positive and negative ends, and that you should be sure to insert them correctly.

Black

Red

Press the button of the speaker jack and keep it pressed down as you insert the wire of the speaker cord and then release the button.

75

Speaker System: PDP-S55-LR

3) Care and Maintenance

When the cabinet gets dirty...

Wipe with a lit-free, soft, dry cloth.

If the cabinet is heavily soiled, soak a cloth in a neutral detergent solution, wring well, and wipe the cabinet. Remove any remaining moisture by wiping with a dry colth.

If you want to use a chemical cloth for cleaning, read any caution information provided with the chemical cloth product.

Do not use solvent such as thinner or benzine for cleaning. These chemical can damage the surface finish, deteriorating or stripping the coating.

To remove dust from the speaker nets, use a vacuum cleaner’s. Avoid applying the vacuum cleaner hose directly to the speakers without using a brush adapter or using a nozzle adapter.

To prevent damage to the cabinet and speaker nets, do not scrach or hit them with hard objects. Also, do not stab the speaker nets with sharp objects.

Do not apply volatile chemicals such as insecticide on the cabinet. Avoid leaving a rubber or vinyl products in contact with the cabinet for prolonged periods. The surface finish can deteriorate or the coating may be stripped off.

76

Speaker System: PDP-S55-LR

77

Before Beginning Adjustment/Setting

5.1 Before Beginning Adjustment

There are three methods for adjusting this display:

Main control panel

Remote control

Personal computer (RS-232C control)

Carefully read and gain a good understanding of this section before beginning adjustment. Items that apply only when a PDA-5003 or PDA-5004 is installed, are indicated with a ‘ ’.

5.1.1 Operation Mode

This display is divided into the following four operating modes.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(Note 2)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Power standby state

 

 

 

 

 

 

 

 

 

 

 

 

Power management

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

standby state

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ON indicator flashes

 

 

 

 

STANDBY/ON

<PON>

<POF>

 

 

No input

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INPUT1 to INPUT5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MENU

 

 

 

1 Normal operation mode

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Press for three

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(Note 1)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MENU

 

 

 

 

 

seconds or more.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DISPLAY

 

 

 

 

DISPLAY

 

 

MENU

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2 Menu Mode

 

 

 

 

 

 

 

3 Integrator Mode

 

 

 

 

 

 

 

 

 

 

4 RS-232C Adjustment

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

indicates the operation modes and states

indicates button controls on the remote control or main-control panel

<> indicates controls by RS-232C commands

(Note 1) Refer to section 5.4.1, “About the Integrator Mode” (pg. 142).

(Note 2) Power management standby state exists only when power management is set.

1 Normal Operation Mode

This mode is for displaying signals.

In this mode the following basic controls are available:

Switching to the power standby state

Switching the input

Switching the screen

Adjusting the volume

Muting the sound (remote control only)

Setting the AUTO SET UP

Applying the POINT ZOOM (remote control only)

Accessing Multi screens (remote control only)

Activating the menu mode or the integrator mode

In addition, some control via RS-232C commands is possible (Refer to section 5.5.5, “List of RS-232C Commands” (pg. 194)).

2 Menu Mode

This mode is for adjusting the image quality, changing the screen position, and assigning various settings. For details, refer to section 5.3, “Menu Mode” (pg. 101).

In this mode, it is possible to change adjustment data within a limited range. These adjustments are based on values set in the integrator mode or RS-232C commands (to be described later).

78 For details, refer to section 5.3, “Menu Mode” (pg. 101).

Before Beginning Adjustments

3 Integrator Mode

This mode provides an adjustment function for integrator options.

This mode has white-balance adjustment and various detailed settings in addition to the items in the menu mode. For details, refer to section 5.4, “Integrator Mode” (pg. 142).

4 RS-232C Adjustment

In this mode, a personal computer is used to perform various adjustments and settings.

There are some items that can only be configured in this mode.

Note

When connecting multiple sets and in this mode, assign an ID before making adjustments or settings.

For details, refer to section 5.5, “RS-232C Adjustment” (pg. 189).

5.1.2 Combined Use of the Remote Control, Main-control Panel, and RS-232C Commands

• The remote control and main-control panel can be operated together.

(Example) It is possible to access the Menu Mode using the main-control panel then perform an adjustment using the remote control.

• With the remote-control (or main-control panel) buttons and RS-232C commands, the most resent control has priority.

79

Before Beginning Adjustments

5.1.3 List of Input Correspondence Signals

1) Input correspondence signals (personal computer signals)

INPUT1

: Not available.

 

Resolution

Refresh rate

 

Screen size (Dot x line)

Remarks

(Dot x Line)

Vertical

Horizontal

DOT BY DOT

4:3

FULL

 

 

 

 

 

 

 

 

 

 

640x400

70.1 Hz

31.5 kHz

 

 

 

NEC PC-9800

 

 

 

 

640x400

 

1365x768

 

 

720x400

70.1 Hz

31.5 kHz

 

 

 

NEC PC-9800

 

 

 

 

720x400

 

1365x768

 

 

 

85.1 Hz

37.9 kHz

±

 

±

 

 

640x480

59.9 Hz

31.5 kHz

640x480

1024x768

1365x768

 

 

 

 

 

 

 

 

 

66.7 Hz

35.0 kHz

±

±

±

Apple Macintosh 13”

 

72.8 Hz

37.9 kHz

±

±

±

 

 

 

75 Hz

37.5 kHz

±

±

±

 

 

 

85 Hz

43.3 kHz

±

±

±

 

 

 

100.4 Hz

51.1 kHz

±

±

±

I/O DATA

 

120.4 Hz

61.3 kHz

±

±

±

I/O DATA

848x480

60 Hz

31.0 kHz

 

 

 

 

 

 

 

 

 

848x480

 

1365x768

 

 

852x480

60 Hz

31.7 kHz

 

 

 

I/O DATA

 

 

 

 

852x480

 

1365x768

 

 

800x600

56.3 Hz

35.2 kHz

 

 

 

 

 

 

 

 

 

800x600

1024x768

1365x768

 

 

 

60.3 Hz

37.9 kHz

±

±

±

 

 

 

72.2 Hz

48.1 kHz

±

±

±

 

 

 

75 Hz

46.9 kHz

±

±

±

 

 

 

85.1 Hz

53.7 kHz

±

±

±

 

 

 

99.8 Hz

63.0 kHz

±

±

±

I/O DATA

 

120 Hz

75.7 kHz

±

±

±

I/O DATA

832x624

74.6 Hz

49.7 kHz

 

 

 

Apple Macintosh 16”

 

 

 

 

832x624

1024x768

1365x768

 

 

1024x768

60 Hz

48.4 kHz

 

 

 

 

 

 

 

 

 

1024x768

 

1365x768

 

 

 

60 Hz

49.7 kHz

±

 

±

Work station (SGI)

 

70.1 Hz

56.5 kHz

±

 

±

 

 

 

 

 

 

 

 

 

 

75 Hz

60.0 kHz

±

 

±

( ) indicates

 

(74.9 Hz)

(60.2 kHz)

 

 

 

Apple Macintosh 19”

 

85 Hz

68.7 kHz

±

 

±

 

 

 

100.6 Hz

80.5 kHz

±

 

±

I/O DATA

 

119.4 Hz

95.5 kHz

±

 

±

 

 

1280x768

56.2 Hz

45.1 kHz

 

 

 

 

 

 

 

 

 

1280x768

 

1365x768

 

 

 

59.8 Hz

48 kH

z

±

 

±

 

 

 

69.8 Hz

56 kH

z

±

 

±

 

 

1360x768

60 Hz

47.7 kHz

 

 

 

I/O DATA

 

 

 

 

1360x768

 

1365x768

 

 

1376x768

59.9 Hz

48.3 kHz

 

 

 

I/O DATA

 

 

 

 

 

 

1365x768

 

 

1280x800

59.8 Hz

49.7 kHz

 

 

 

CVT

 

 

 

 

 

 

1365x768

 

 

1280x854

60 Hz

53.1 kHz

 

 

 

PC

 

 

 

 

 

 

1365x768

 

 

1152x864

60 Hz

53.7 kHz

 

 

 

 

 

 

 

 

 

 

1024x768

1365x768

 

 

 

72 Hz

64.9 kHz

 

±

±

 

 

 

75 Hz

67.5 kHz

 

±

±

 

 

1152x870

75.1 Hz

68.7 kHz

 

 

 

Apple Macintosh 21”

 

 

 

 

 

 

1024x768

1365x768

 

 

1152x900

66 Hz

61.8 kHz

 

 

 

Sun Microsystems LO

 

 

 

 

 

1024x768

1365x768

 

 

 

76 Hz

71.7 kHz

 

±

±

Sun Microsystems HI

80

 

 

 

 

 

Before Beginning Adjustments

 

 

 

 

 

 

 

 

Resolution

Refresh rate

Screen size (Dot x line)

Remarks

(Dot x Line)

Vertical

 

Horizontal

DOT BY DOT

4:3

FULL

 

 

 

1440x900

59.9 Hz

 

55.9 kHz

 

 

 

Apple Macintosh 17”

 

 

 

 

 

 

1365x768

 

 

1280x960

60 Hz

 

60.0 kHz

 

 

 

 

 

 

 

 

 

 

1024x768

1365x768

 

 

 

85 Hz

 

85.9 kHz

 

±

±

 

 

1280x1024

60 Hz

 

63.9 kHz

 

1024x768

1365x768

Work station (SGI)

 

 

 

 

 

 

 

 

60 Hz

 

64.0 kHz

 

±

±

 

 

 

60 Hz

 

64.6 kHz

 

±

±

Work station (EWS4800)

 

71.2 Hz

 

75.1 kHz

 

±

±

Work station (EWS4800)

 

72 Hz

 

78.1 kHz

 

±

±

Work station (HP)

 

75 Hz

 

80.0 kHz

 

±

±

 

 

 

76.1 Hz

 

81.1 kHz

 

±

±

Work station (SUN)

 

85 Hz

 

91.1 kHz

 

±

±

 

 

 

100.1 Hz

 

108.5 kHz

 

±

±

I/O DATA

1400x1050

60 Hz

 

65.3 kHz

 

 

 

 

 

 

 

 

 

 

1024x768

1365x768

 

 

 

74.9 Hz

 

82.3 kHz

 

±

±

 

 

 

85 Hz

 

93.9 kHz

 

±

±

 

 

1680x1050

60 Hz

 

65.3 kHz

 

 

 

 

 

 

 

 

 

 

 

1365x768

 

 

1600x1200

60 Hz

 

75.0 kHz

 

 

 

 

 

 

 

 

 

 

1024x768

1365x768

 

 

 

65 Hz

 

81.3 kHz

 

±

±

 

 

 

70 Hz

 

87.5 kHz

 

±

±

 

 

 

75 Hz

 

93.8 kHz

 

±

±

 

 

 

85 Hz

 

106.3 kHz

 

±

±

 

 

1920x1200

59.9 Hz

 

74.6 kHz

 

 

 

CVT

 

 

 

 

 

 

1365x768

 

 

1920x1200RB*

60 Hz

 

74.0 kHz

 

 

 

CVT

 

 

 

 

 

 

1365x768

 

 

 

 

 

: Optimal picture. Adjustment of picture position, refresh rate, phase etc., may be necessary

 

 

 

: Picture will be enlarged but some fine detail will be hard to see.

 

 

 

: Simple reproduction. Fine detail will not be reproduced.

 

 

 

 

RB*: Abbreviation for Reduce Blanking that is set by CVT.

 

 

INPUT2

 

 

 

 

 

 

 

: Not available.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Resolution

Refresh rate

Screen size (Dot x line)

Remarks

(Dot x Line)

Vertical

 

Horizontal

DOT BY DOT

4:3

FULL

 

 

 

 

 

 

 

 

 

 

 

720x400

70.1 Hz

 

31.5 kHz

 

 

 

NEC PC-9800

 

 

 

 

720x400

 

1365x768

 

 

 

85.1 Hz

 

37.9 kHz

±

 

±

 

 

640x480

59.9 Hz

 

31.5 kHz

 

 

 

 

 

 

 

 

 

640x480

1024x768

1365x768

 

 

 

72.8 Hz

 

37.9 kHz

±

±

±

 

 

 

75 Hz

 

37.5 kHz

±

±

±

 

 

 

85 Hz

 

43.3 kHz

±

±

±

 

 

 

100.4 Hz

 

51.1 kHz

±

±

±

 

 

 

120.4 Hz

 

61.3 kHz

±

±

±

 

 

848x480

60 Hz

 

31.0 kHz

 

 

 

 

 

 

 

 

 

848x480

 

1365x768

 

 

852x480

60 Hz

 

31.7 kHz

 

 

 

 

 

 

 

 

 

852x480

 

1365x768

 

 

800x600

56.3 Hz

 

35.2 kHz

800x600

1024x768

1365x768

 

 

 

 

 

 

 

 

 

60.3 Hz

 

37.9 kHz

±

±

±

 

 

 

72.2 Hz

 

48.1 kHz

±

±

±

 

 

 

75 Hz

 

46.9 kHz

±

±

±

 

 

 

85.1 Hz

 

53.7 kHz

±

±

±

 

 

 

99.8 Hz

 

63.0 kHz

±

±

±

 

 

 

120 Hz

 

75.7 kHz

±

±

±

 

 

81

Before Beginning Adjustments

 

 

 

 

 

 

 

 

 

: Not available.

 

 

 

 

 

 

 

 

 

Resolution

Refresh rate

Screen size (Dot x line)

 

Remarks

(Dot x Line)

Vertical

 

Horizontal

DOT BY DOT

4:3

FULL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1024x768

60 Hz

 

48.4 kHz

1024x768

 

1365x768

 

 

 

 

 

 

 

 

 

 

 

 

60 Hz

 

49.7 kHz

±

 

±

 

Work station (SGI)

 

70.1 Hz

 

56.5 kHz

±

 

±

 

 

 

 

75 Hz

 

60.0 kHz

±

 

±

 

 

 

 

85 Hz

 

68.7 kHz

±

 

±

 

 

 

 

100.6 Hz

 

80.5 kHz

±

 

±

 

 

 

 

119.4 Hz

 

95.5 kHz

±

 

±

 

 

 

1280x768

56.2 Hz

 

45.1 kHz

1280x768

 

1365x768

 

 

 

 

 

 

 

 

 

 

 

 

59.8 Hz

 

48 kH z

±

 

±

 

 

 

 

69.8 Hz

 

56 kH z

±

 

±

 

 

 

1280x800

59.8 Hz

 

49.7 kHz

 

 

1365x768

 

 

 

 

 

 

 

 

 

 

 

 

1280x854

60 Hz

 

53.1 kHz

 

 

 

 

 

 

 

 

 

 

 

 

1365x768

 

 

 

1360x768

60 Hz

 

47.7 kHz

1360x768

 

 

 

I/O DATA

 

 

 

 

 

1365x768

 

 

 

1376x768

59.9 Hz

 

48.3 kHz

 

 

 

 

I/O DATA

 

 

 

 

 

 

1365x768

 

 

 

1152x864

60 Hz

 

53.7 kHz

 

 

 

 

 

 

 

 

 

 

 

1024x768

1365x768

 

 

 

 

72 Hz

 

64.9 kHz

 

±

±

 

 

 

 

75 Hz

 

67.5 kHz

 

±

±

 

 

 

1152x900

66 Hz

 

61.8 kHz

 

1024x768

1365x768

 

Sun Microsystems LO

 

 

 

 

 

 

 

 

 

76 Hz

 

71.7 kHz

 

±

±

 

Sun Microsystems HI

1440x900

59.9 Hz

 

55.9 kHz

 

 

1365x768

 

Apple Macintosh17”

 

 

 

 

 

 

 

 

 

1280x960

60 Hz

 

60.0 kHz

 

1024x768

1365x768

 

 

 

 

 

 

 

 

 

 

 

 

85 Hz

 

85.9 kHz

 

±

±

 

 

 

1280x1024

60 Hz

 

63.9 kHz

 

1024x768

1365x768

 

Work station (SGI)

 

 

 

 

 

 

 

60 Hz

 

64.0 kHz

 

±

±

 

 

 

 

60 Hz

 

64.6 kHz

 

±

±

 

Work station (EWS4800)

 

71.2 Hz

 

75.1 kHz

 

±

±

 

Work station (EWS4800)

 

72 Hz

 

78.1 kHz

 

±

±

 

Work station (HP)

 

75 Hz

 

80.0 kHz

 

±

±

 

 

 

 

76.1 Hz

 

81.1 kHz

 

±

±

 

Work station (SUN)

 

85 Hz

 

91.1 kHz

 

±

±

 

 

 

1400x1050

60 Hz

 

65.3 kHz

 

1024x768

1365x768

 

 

 

 

 

 

 

 

 

 

 

 

74.9 Hz

 

82.3 kHz

 

±

±

 

 

 

1680x1050

60 Hz

 

65.3 kHz

 

 

 

 

 

 

 

 

 

 

 

 

1365x768

 

 

 

1920x1080

50 Hz

 

56.2 kHz

 

 

 

 

 

 

 

 

 

 

 

 

1365x768

 

 

 

 

60 Hz

 

67.5 kHz

 

 

±

 

 

 

1600x1200

60 Hz

 

75.0 kHz

 

1024x768

1365x768

 

CVT

 

 

 

 

 

 

 

 

1920x1200RB*

60 Hz

 

74.0 kHz

 

 

1365x768

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

: Optimal picture. Adjustment of picture position, refresh rate, phase etc., may be necessary.

 

 

 

: Picture will be enlarged but some fine detail will be hard to see.

 

 

 

 

 

: Simple reproduction. Fine detail will not be reproduced.

 

 

 

 

RB*: Abbreviation for Reduce Blanking that is set by CVT.

 

 

Note

In rare cases, the picture may not translate properly when switching between compatible signal formats on the output device (PC, etc.). Should this happen, turn off the power and then turn it back on again.

82

Before Beginning Adjustments

2) Screen size

Unit: % (percent)

Screen size

Personal computer signal

Remarks

DOT BY DOT

100

This screen size exists for a personal

The input signal corresponds 1:1 with the

computer signal when the input signals a

 

pixels of the Plasma Display for an accurate

 

less than the pixels of the plasma display.

reproduction.

100

For details, refer to the correspondence

 

signal table.

100

100

 

4:3

For a 4:3 source, roundness can be accurately 100 reproduced (In order to prevent burning of the

screen, this screen size should not be used

unless required).

100

100

100

FULL

100

This is for wide-screen video (squeeze) (For a

 

16:9 source, roundness is nearly accurate).

 

 

100

100

100

The screen size settings are stored in memory for each function and for each input signal. Up to eight (8) sizes can be stored in memory for each function.

83

Before Beginning Adjustments

3) Input correspondence signals (video signals) (Applicable only when a PDA-5003/PDA-5004 is installed.)

INPUT1, INPUT5

: Not available.

 

Refresh rate

 

Screen size

 

 

Vertical

Horizontal

Signal format

FULL ZOOM WIDE

14:9

Remarks

fV (Hz)

fH (kHz)

4:3

2.35:1

 

 

 

 

 

15.625

Component

 

 

625i (576i)/SDTV

 

RGB

 

 

 

 

 

 

 

 

28.13

Component

 

 

1125i (1080i)/HDTV

 

RGB

 

 

 

 

 

 

 

 

31.25

Component

 

 

625p (576p)/SDTV

 

RGB

 

 

50

 

 

 

 

 

Component

 

 

 

 

37.50

 

 

750p (720p)/HDTV

 

RGB

 

 

 

 

 

 

 

 

56.20

Component

*1

 

1125p (1080p)/HDTV

 

 

 

 

RGB

*1

 

 

 

 

 

 

 

 

 

 

 

62.50

Component

*1

 

1250p/HDTV

 

 

 

 

RGB

*1

 

 

 

 

 

 

 

 

 

 

 

15.734

Component

 

 

525i (480i)/SDTV

 

RGB

 

 

 

 

 

 

 

 

31.5

Component

 

 

525p (480p)/SDTV

 

RGB

 

 

 

 

 

 

 

60

33.75

Component

 

 

1125i (1080i)/HDTV

RGB

 

 

1125i (1035i)/HDTV

 

 

 

 

 

45.0

Component

 

 

750p (720p)/HDTV

 

RGB

 

 

 

 

 

 

 

 

67.5

Component

*1

 

1125p (1080p)/HDTV

 

 

 

 

RGB

*1

 

 

 

 

 

 

 

 

 

 

*1: Some visual distortion may occur depending on the combination of connected components.

INPUT2

 

 

 

: Not available.

Vertical

Horizontal

Signal

 

Screen size

 

Remarks

fV (Hz)

fH (kHz)

format

4:3

FULL ZOOM WIDE 14:9 2.35:1

 

28.13

RGB

 

1125i(1080i)/HDTV

50

31.25

RGB

 

625p(576p)/SDTV

 

37.50

RGB

 

750p(720p)/HDTV

 

31.5

RGB

 

525p(480p)/SDTV

60

33.75

RGB

 

1125i(1080i)/HDTV

 

45.0

RGB

 

750p(720p)/HDTV

The following signals are not formally supported but can be displayed (not recorded in EDID data).

Vertical

Horizontal

Signal

 

 

Screen size

Remarks

 

 

 

fV (Hz)

fH (kHz)

format

4:3

FULL

ZOOM WIDE 14:9 2.35:1

 

 

15.6

RGB

 

 

 

625i(576i)/SDTV

50

56.25

RGB

 

 

 

1125p(1080p)/HDTV

 

15.8

RGB

 

 

 

525i(480i)/SDTV

60

31.5

RGB

 

 

 

525p(480p)x640 dot/SDTV

67.5

RGB

 

 

 

1125p(1080p)/HDTV

 

 

 

 

50

62.5

RGB

 

 

 

1250p/HDTV

*May not be displayed accurately depending on the connected device

84

Before Beginning Adjustments

INPUT3

 

Signal Format

 

 

 

Screen size

 

 

Remark

 

 

 

 

 

 

 

 

 

 

 

4 : 3

FULL

ZOOM

 

WIDE

CINEMA

14:9

2.35:1

 

 

 

 

 

 

 

 

 

 

 

 

NTSC

S-Video (Y/C)

 

 

 

 

 

 

 

 

 

 

 

 

 

PAL

S-Video (Y/C)

 

 

SECAM

S-Video (Y/C)

 

 

 

 

 

 

 

 

 

 

 

 

 

4.43 NTSC

S-Video (Y/C)

 

 

 

 

 

 

 

 

 

 

 

 

 

PAL M

S-Video (Y/C)

 

 

PAL N

S-Video (Y/C)

 

 

INPUT4

 

 

 

 

 

Screen size

 

 

 

 

Signal Format

4 : 3

FULL

ZOOM

 

WIDE

CINEMA

14:9

2.35:1

Remark

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NTSC

Composite

 

 

 

 

 

 

 

 

 

 

 

 

 

PAL

Composite

 

 

SECAM

Composite

 

 

4.43 NTSC

Composite

 

 

 

 

 

 

 

 

 

 

 

 

 

PAL M

Composite

 

 

PAL N

Composite

 

 

‘UNDERSCAN’ is for display-screen sizes other than those given in the table above. This size can be set using ‘PRO USE’ in the integrator mode.

85

Before Beginning Adjustments

 

4) Input correspondence signals (personal computer signals)

 

INPUT1, INPUT5 (Applicable only when a PDA-5003/PDA-5004 is installed.)

: Not available.

 

Resolution

Refresh rate

 

Screen size (Dot x line)

Remarks

(Dot x Line)

Vertical

Horizontal

DOT BY DOT

4:3

FULL

 

 

640x400

70.1 Hz

31.5 kHz

 

 

 

NEC PC-9800

 

 

 

 

640x400

 

1365x768

 

 

720x400

70.1 Hz

31.5 kHz

 

 

 

NEC PC-9800

 

 

 

 

720x400

 

1365x768

 

 

 

85.1 Hz

37.9 kHz

±

 

±

 

 

640x480

59.9 Hz

31.5 kHz

640x480

1024x768

1365x768

 

 

 

 

 

 

 

 

 

66.7 Hz

35.0 kHz

±

±

±

Apple Macintosh 13”

 

72.8 Hz

37.9 kHz

±

±

±

 

 

 

75 Hz

37.5 kHz

±

±

±

 

 

 

85 Hz

43.3 kHz

±

±

±

 

 

 

100.4 Hz

51.1 kHz

±

±

±

I/O DATA

 

120.4 Hz

61.3 kHz

±

±

±

I/O DATA

848x480

60 Hz

31.0 kHz

 

 

 

 

 

 

 

 

 

848x480

 

1365x768

 

 

852x480

60 Hz

31.7 kHz

 

 

 

I/O DATA

 

 

 

 

852x480

 

1365x768

 

 

800x600

56.3 Hz

35.2 kHz

 

 

 

 

 

 

 

 

 

800x600

1024x768

1365x768

 

 

 

60.3 Hz

37.9 kHz

±

±

±

 

 

 

72.2 Hz

48.1 kHz

±

±

±

 

 

 

75 Hz

46.9 kHz

±

±

±

 

 

 

85.1 Hz

53.7 kHz

±

±

±

 

 

 

99.8 Hz

63.0 kHz

±

±

±

I/O DATA

 

120 Hz

75.7 kHz

±

±

±

I/O DATA

832x624

74.6 Hz

49.7 kHz

 

 

 

Apple Macintosh 16”

 

 

 

 

832x624

1024x768

1365x768

 

 

1024x768

60 Hz

48.4 kHz

 

 

 

 

 

 

 

 

 

1024x768

 

1365x768

 

 

 

60 Hz

49.7 kHz

±

 

±

Work station (SGI)

 

70.1 Hz

56.5 kHz

±

 

±

 

 

 

 

 

 

 

 

 

 

75 Hz

60.0 kHz

±

 

±

( ) indicates

 

(74.9 Hz)

(60.2 kHz)

 

 

 

Apple Macintosh 19”

 

85 Hz

68.7 kHz

±

 

±

 

 

 

100.6 Hz

80.5 kHz

±

 

±

I/O DATA

 

119.4 Hz

95.5 kHz

±

 

±

 

 

1280x768

56.2 Hz

45.1 kHz

 

 

 

 

 

 

 

 

 

1280x768

 

1365x768

 

 

 

59.8 Hz

48 kH

z

±

 

±

 

 

 

69.8 Hz

56 kH

z

±

 

±

 

 

1360x768

60 Hz

47.7 kHz

 

 

 

I/O DATA

 

 

 

 

1360x768

 

1365x768

 

 

1376x768

59.9 Hz

48.3 kHz

 

 

 

I/O DATA

 

 

 

 

 

 

1365x768

 

 

1280x800

59.8 Hz

49.7 kHz

 

 

 

CVT

 

 

 

 

 

 

1365x768

 

 

1280x854

60 Hz

53.1 kHz

 

 

 

PC

 

 

 

 

 

 

1365x768

 

 

1152x864

60 Hz

53.7 kHz

 

 

 

 

 

 

 

 

 

 

1024x768

1365x768

 

 

 

72 Hz

64.9 kHz

 

±

±

 

 

 

75 Hz

67.5 kHz

 

±

±

 

 

1152x870

75.1 Hz

68.7 kHz

 

 

 

Apple Macintosh 21”

 

 

 

 

 

 

1024x768

1365x768

 

 

1152x900

66 Hz

61.8 kHz

 

 

 

Sun Microsystems LO

 

 

 

 

 

1024x768

1365x768

 

 

 

76 Hz

71.7 kHz

 

±

±

Sun Microsystems HI

86

 

 

 

 

 

Before Beginning Adjustments

 

 

 

 

 

 

 

 

Resolution

Refresh rate

Screen size (Dot x line)

Remarks

(Dot x Line)

Vertical

 

Horizontal

DOT BY DOT

4:3

FULL

 

 

 

 

 

 

 

 

 

 

 

1440x900

59.9 Hz

 

55.9 kHz

 

 

 

Apple Macintosh 17”

 

 

 

 

 

 

1365x768

 

 

1280x960

60 Hz

 

60.0 kHz

 

 

 

 

 

 

 

 

 

 

1024x768

1365x768

 

 

 

85 Hz

 

85.9 kHz

 

±

±

 

 

1280x1024

60 Hz

 

63.9 kHz

 

1024x768

1365x768

Work station (SGI)

 

 

 

 

 

 

 

 

60 Hz

 

64.0 kHz

 

±

±

 

 

 

60 Hz

 

64.6 kHz

 

±

±

Work station (EWS4800)

 

71.2 Hz

 

75.1 kHz

 

±

±

Work station (EWS4800)

 

72 Hz

 

78.1 kHz

 

±

±

Work station (HP)

 

75 Hz

 

80.0 kHz

 

±

±

 

 

 

76.1 Hz

 

81.1 kHz

 

±

±

Work station (SUN)

 

85 Hz

 

91.1 kHz

 

±

±

 

 

 

100.1 Hz

 

108.5 kHz

 

±

±

I/O DATA

1400x1050

60 Hz

 

65.3 kHz

 

 

 

 

 

 

 

 

 

 

1024x768

1365x768

 

 

 

74.9 Hz

 

82.3 kHz

 

±

±

 

 

 

85 Hz

 

93.9 kHz

 

±

±

 

 

1680x1050

60 Hz

 

65.3 kHz

 

 

 

 

 

 

 

 

 

 

 

1365x768

 

 

1600x1200

60 Hz

 

75.0 kHz

 

 

 

 

 

 

 

 

 

 

1024x768

1365x768

 

 

 

65 Hz

 

81.3 kHz

 

±

±

 

 

 

70 Hz

 

87.5 kHz

 

±

±

 

 

 

75 Hz

 

93.8 kHz

 

±

±

 

 

 

85 Hz

 

106.3 kHz

 

±

±

 

 

1920x1200

59.9 Hz

 

74.6 kHz

 

 

 

CVT

 

 

 

 

 

 

1365x768

 

 

1920x1200RB*

60 Hz

 

74.0 kHz

 

 

 

CVT

 

 

 

 

 

 

1365x768

 

 

 

 

 

: Optimal picture. Adjustment of picture position, refresh rate, phase etc., may be necessary

 

 

 

: Picture will be enlarged but some fine detail will be hard to see.

 

 

 

: Simple reproduction. Fine detail will not be reproduced.

 

 

 

 

RB*: Abbreviation for Reduce Blanking that is set by CVT.

 

 

INPUT2

 

 

 

 

 

 

 

: Not available.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Resolution

Refresh rate

Screen size (Dot x line)

Remarks

(Dot x Line)

Vertical

 

Horizontal

DOT BY DOT

4:3

FULL

 

 

 

 

 

 

 

 

 

 

 

720x400

70.1 Hz

 

31.5 kHz

 

 

 

NEC PC-9800

 

 

 

 

720x400

 

1365x768

 

 

 

85.1 Hz

 

37.9 kHz

±

 

±

 

 

640x480

59.9 Hz

 

31.5 kHz

 

 

 

 

 

 

 

 

 

640x480

1024x768

1365x768

 

 

 

72.8 Hz

 

37.9 kHz

±

±

±

 

 

 

75 Hz

 

37.5 kHz

±

±

±

 

 

 

85 Hz

 

43.3 kHz

±

±

±

 

 

 

100.4 Hz

 

51.1 kHz

±

±

±

 

 

 

120.4 Hz

 

61.3 kHz

±

±

±

 

 

848x480

60 Hz

 

31.0 kHz

 

 

 

 

 

 

 

 

 

848x480

 

1365x768

 

 

852x480

60 Hz

 

31.7 kHz

 

 

 

 

 

 

 

 

 

852x480

 

1365x768

 

 

800x600

56.3 Hz

 

35.2 kHz

800x600

1024x768

1365x768

 

 

 

 

 

 

 

 

 

60.3 Hz

 

37.9 kHz

±

±

±

 

 

 

72.2 Hz

 

48.1 kHz

±

±

±

 

 

 

75 Hz

 

46.9 kHz

±

±

±

 

 

 

85.1 Hz

 

53.7 kHz

±

±

±

 

 

 

99.8 Hz

 

63.0 kHz

±

±

±

 

 

 

120 Hz

 

75.7 kHz

±

±

±

 

 

87

Before Beginning Adjustments

 

 

 

 

 

 

 

 

 

: Not available.

 

 

 

 

 

 

 

 

 

Resolution

Refresh rate

Screen size (Dot x line)

 

Remarks

(Dot x Line)

Vertical

 

Horizontal

DOT BY DOT

4:3

FULL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1024x768

60 Hz

 

48.4 kHz

1024x768

 

1365x768

 

 

 

 

 

 

 

 

 

 

 

 

60 Hz

 

49.7 kHz

±

 

±

 

Work station (SGI)

 

70.1 Hz

 

56.5 kHz

±

 

±

 

 

 

 

75 Hz

 

60.0 kHz

±

 

±

 

 

 

 

85 Hz

 

68.7 kHz

±

 

±

 

 

 

 

100.6 Hz

 

80.5 kHz

±

 

±

 

 

 

 

119.4 Hz

 

95.5 kHz

±

 

±

 

 

 

1280x768

56.2 Hz

 

45.1 kHz

1280x768

 

1365x768

 

 

 

 

 

 

 

 

 

 

 

 

59.8 Hz

 

48 kH z

±

 

±

 

 

 

 

69.8 Hz

 

56 kH z

±

 

±

 

 

 

1280x800

59.8 Hz

 

49.7 kHz

 

 

1365x768

 

 

 

 

 

 

 

 

 

 

 

 

1280x854

60 Hz

 

53.1 kHz

 

 

 

 

 

 

 

 

 

 

 

 

1365x768

 

 

 

1360x768

60 Hz

 

47.7 kHz

1360x768

 

 

 

I/O DATA

 

 

 

 

 

1365x768

 

 

 

1376x768

59.9 Hz

 

48.3 kHz

 

 

 

 

I/O DATA

 

 

 

 

 

 

1365x768

 

 

 

1152x864

60 Hz

 

53.7 kHz

 

 

 

 

 

 

 

 

 

 

 

1024x768

1365x768

 

 

 

 

72 Hz

 

64.9 kHz

 

±

±

 

 

 

 

75 Hz

 

67.5 kHz

 

±

±

 

 

 

1152x900

66 Hz

 

61.8 kHz

 

1024x768

1365x768

 

Sun Microsystems LO

 

 

 

 

 

 

 

 

 

76 Hz

 

71.7 kHz

 

±

±

 

Sun Microsystems HI

1440x900

59.9 Hz

 

55.9 kHz

 

 

1365x768

 

Apple Macintosh17”

 

 

 

 

 

 

 

 

 

1280x960

60 Hz

 

60.0 kHz

 

1024x768

1365x768

 

 

 

 

 

 

 

 

 

 

 

 

85 Hz

 

85.9 kHz

 

±

±

 

 

 

1280x1024

60 Hz

 

63.9 kHz

 

1024x768

1365x768

 

Work station (SGI)

 

 

 

 

 

 

 

60 Hz

 

64.0 kHz

 

±

±

 

 

 

 

60 Hz

 

64.6 kHz

 

±

±

 

Work station (EWS4800)

 

71.2 Hz

 

75.1 kHz

 

±

±

 

Work station (EWS4800)

 

72 Hz

 

78.1 kHz

 

±

±

 

Work station (HP)

 

75 Hz

 

80.0 kHz

 

±

±

 

 

 

 

76.1 Hz

 

81.1 kHz

 

±

±

 

Work station (SUN)

 

85 Hz

 

91.1 kHz

 

±

±

 

 

 

1400x1050

60 Hz

 

65.3 kHz

 

1024x768

1365x768

 

 

 

 

 

 

 

 

 

 

 

 

74.9 Hz

 

82.3 kHz

 

±

±

 

 

 

1680x1050

60 Hz

 

65.3 kHz

 

 

 

 

 

 

 

 

 

 

 

 

1365x768

 

 

 

1920x1080

50 Hz

 

56.2 kHz

 

 

 

 

 

 

 

 

 

 

 

 

1365x768

 

 

 

 

60 Hz

 

67.5 kHz

 

 

±

 

 

 

1600x1200

60 Hz

 

75.0 kHz

 

1024x768

1365x768

 

CVT

 

 

 

 

 

 

 

 

1920x1200RB*

60 Hz

 

74.0 kHz

 

 

1365x768

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

: Optimal picture. Adjustment of picture position, refresh rate, phase etc., may be necessary.

 

 

 

: Picture will be enlarged but some fine detail will be hard to see.

 

 

 

 

 

: Simple reproduction. Fine detail will not be reproduced.

 

 

 

 

RB*: Abbreviation for Reduce Blanking that is set by CVT.

 

 

Note

In rare cases, the picture may not translate properly when switching between compatible signal formats on the output device (PC, etc.). Should this happen, turn off the power and then turn it back on again.

88

 

 

 

Before Beginning Adjustments

5) Screen size

 

 

 

Unit: % (percent)

 

 

 

 

 

 

 

 

 

 

 

When a video card is installed

Personal computer

 

 

Screen size

 

 

Remarks

Video signal 4:3 source

Video signal 16:9 source

signal

 

(NTSC, 625i, etc.)

(750p, 1080i, etc.)

 

 

 

 

 

 

DOT BY DOT

 

 

 

 

 

100

This screen size exists for a personal computer

The input signal corresponds 1:1

 

 

 

 

 

signal when the input signals a less than the pixels

with the pixels of the Plasma

 

 

 

 

 

 

of the plasma display. For details, refer to the

Display for an accurate

 

 

 

 

 

100

correspondence signal table.

reproduction.

 

 

 

 

 

 

 

 

 

 

100

100

 

 

 

 

 

 

 

4:3

 

 

95

 

 

100

 

For a 4:3 source, roundness can

 

 

 

 

 

 

 

be accurately reproduced (In order

 

 

 

 

 

 

 

to prevent burning of the screen,

 

 

 

 

 

 

 

this screen size should not be

 

 

95

 

 

100

 

used when possible).

95

95

 

 

100

100

 

FULL

 

 

95

 

95

100

 

This is for wide-screen video

 

 

 

 

 

 

 

 

 

 

 

(squeeze) (For a 16:9 source,

 

 

 

 

 

 

 

roundness is nearly accurate).

 

 

 

 

 

 

 

 

 

 

95

 

95

100

 

 

95

95

95

95

100

100

 

ZOOM

 

 

73

 

 

 

 

For a video signal, this is for a

 

 

 

 

 

 

 

cinesco (cinema scope) size video.

 

 

 

 

 

 

 

 

 

 

73

 

 

 

95

95

 

 

 

WIDE

 

 

90

90

 

This is for reproducing the 4:3

 

 

 

 

 

portion of a 4:3 source or 16:9

 

 

 

 

 

source on the entire screen

 

 

 

 

 

(roundness near the center is

 

 

90

90

 

nearly accurate).

95

95

72

72

 

 

 

 

 

 

UNDERSCAN

 

 

100

100

When selecting the underscan by switching the

This is used by a broadcast

 

 

 

 

screen size, please set to UNDERSCAN: ON using

station and the like for viewing

 

 

 

 

PRO USE of the integrator mode.

the portion outside the normal

 

 

 

 

 

effective display range.

 

 

100

100

 

 

100

100

100

100

 

2.35:1

 

 

74

74

 

Displays 2.35:1 squeezed image

 

 

 

 

 

full-screen without black border.

 

 

 

 

 

However, portions of image at

 

 

 

 

 

right and left edges are cut.

 

 

74

74

 

 

74

74

74

74

 

14:9

 

 

84

 

 

Displays expanded 4:3 screen

 

 

 

 

 

image without distortion.

 

 

 

 

 

84

9595

The screen size settings are stored in memory for each function and for each input signal. Up to eight (8) sizes can be stored in memory for each function.

89

Before Beginning Adjustments

5.1.4 List of Adjustable and Settable Items

1) Menu Mode

7 PDP-607CMX

*1: INPUT1 case

*2: INPUT2 case

(Note 1) The OPTION settings are common settings for all inputs.

90

Before Beginning Adjustments

7 PDP-607CMX

: Applicable only when a PDA-5003/PDA-5004 is installed. : Cannot be set according to the signal.

*1: INPUT1 case *2: INPUT2 case

(Note 1) The OPTION settings are common settings for all inputs.

91

Before Beginning Adjustments

7 PDA-5003/PDA-5004

: Applicable only when a PDA-5003/PDA-5004 is installed. : Cannot be set according to the signal.

*1: INPUT5 case

*2: INPUT3 or INPUT4 cases

(Note 1) The OPTION settings are common settings for all inputs.

92

Before Beginning Adjustments

7 Slot card other than PDA-5003/PDA-5004

: Applicable only when a video card is installed. : Cannot be set according to the signal.

*1: INPUT3 to INPUT5 analog signal cases *2: INPUT3 to INPUT5 digital signal cases

(Note 1) The OPTION settings are common settings for all inputs.

93

Before Beginning Adjustments

2) Integrator mode

7 PDP-607CMX

(Note) The OPTION settings are common settings for all inputs.

94

Before Beginning Adjustments

7 PDP-607CMX

: Applicable only when a PDA-5003/PDA-5004 is installed.

(Note) The OPTION settings are common settings for all inputs.

95

Before Beginning Adjustments

7 PDA-5003/PDA-5004

: INPUT3 to INPUT5 are applicable only when the PDA-5003 or the PDA-5004 is installed.

(Note) The OPTION settings are common settings for all inputs.

96

Before Beginning Adjustments

7 Slot card other than PDA-5003/PDA-5004

: INPUT3 to INPUT5 are applicable only when the PDA-5003 or the PDA-5004 is installed.

(Note) The OPTION settings are common settings for all inputs.

97

Before Beginning Adjustments

5.1.5 Last Memory

The timing for the last memory is listed below.

When one of the following operations is performed before the timing is complete, the last memory function may not perform.

MAIN POWER switch is turned OFF

Power cord is removed from the power outlet

The breaker to the power outlet is turned OFF

 

Item

 

Saving to Memory

 

 

 

Operation in the normal-

Three seconds after an operation

operation mode

When the standby mode is designated by a remote-control, main-control panel or <POF>

Power ON/OFF

 

command

Switching input

When the format of the displayed signal changes

Switching screen size

(NOTE) Of the RS-232C commands that can be used in the normal-operation mode, there are

Volume adjustment

 

some that cannot be saved in the last memory when using the normal-operation mode.

• FUNCTIONAL LOCK setting

 

For details, refer to section 5.5, “RS-232C Adjustment (pg. 189)”.

 

 

 

Adjustments and settings in the

Three seconds after an operation

menu mode

When the standby mode is designated by a remote-control, main-control panel or <POF>

 

 

 

command

 

 

When the format of the displayed signal changes

 

 

 

Adjustments and settings in the

Three seconds after an operation

integrator mode

When the standby mode is designated by a remote-control, main-control panel or <POF>

 

 

 

command

 

 

When the format of the displayed signal changes

 

 

 

Adjustments and settings in the

Three seconds after a command is sent, or when the next command is sent within four

RS-232C adjustment

 

seconds

 

 

When the standby mode is designated by a remote-control, main-control panel or <POF>

 

 

 

command

 

 

When an adjustment or setting is changed using a command

 

 

When the format of the displayed signal changes

 

 

 

 

Note

If the system is started or stopped by turned ON/OFF from a circuit breaker, use the system only after first saving adjustments and settings in the last memory according to the timing described above. Also, with this operating method, count errors may occur in the hour meter.

5.1.6 Aging

After the power has been turned ON, input a white 100 % signal to age thus stabilize the unit (about 30 minutes). When adjustments are made after aging is performed, it possible to perform more precise adjustments.

Note

When a still screen is displayed for a long period, the image may possibly be burned in to the screen.

98

Normal Operating Mode

5.2 Normal Operation Mode

5.2.1 About normal operation mode

The following controls are possible in the normal operation mode.

1 Switching input

Pressing the [INPUT1] to [INPUT5] buttons on the remote control changes the input that setting.

Pressing the [INPUT] button on the main-control panel changes the input each time the button is pressed.

Note

When a PDA-5003 or a PDA-5004 is not installed, the input switches only between INPUT1 and INPUT2.

2 Switching the screen size

Each time the [SCREEN SIZE] button on the remote control or main-control panel is pressed, the display screen size changes.

When reproducing a PC signal

3 DOT BY DOT

FULL

3 4: 3

3

When reproducing a video signal (signal other than a PC signal) (Applicable only when a PDA-5003 or a PDA5004 is installed.)

 

3 4:3

 

3 FULL

 

3 WIDE

 

 

 

 

 

 

 

 

 

14:9 2

2.35:1 2

ZOOM 2

 

 

 

 

Note

The reproducible screen size changes according to the input signal.

Refer to the section 5.1.3, “List of Input Correspondence Signals” (pg. 80).

To select ‘Underscan’, set the PRO USE option in the integrator mode.

When this display is to be used for commercial use or for public viewing, such as in a coffee shop or hotel, reducing or enlarging the screen by using the screen-size-switching function could infringe on the copyright of the creator according to copyright laws.

2 Display call

APressing the [DISPLAY] button on the remote control or main-control panel displays the current input function, horizontal and vertical frequency of the input signal, the type of signal, and the screen size (DISPLAY CALL 1).

Note

The displayed horizontal and vertical frequencies are measured values. Measurement errors are possible.

BPressing the [DISPLAY] button on the remote control or main-control panel again for three seconds or more when the display described in A above is displayed, cause various settings and internal temperature to be displayed as shown below (DISPLAY CALL 2).

 

 

 

 

 

P D P - 6 0 7 C M X

 

 

 

S E R I A L N O.

: * * * * * * * * * * * * * * * *

 

 

L OT

: 0 0 1 A 0 0 1 K

 

 

DAT E

: 0 0 1 A 0 0 1 X

 

 

H O U R M E T E R

: 0 0 2 3 9 H

 

 

T E M P E R AT U R E

: + 2 5

 

 

O S D

: O N

 

 

BAU D R AT E

: 9 6 0 0 B P S

 

 

FA N C O N T R O L

: AU TO

 

 

I D N O. S E T

: A L L

 

 

C O L O R M O D E

: N O R M A L

 

 

I N F O R M AT I O N

 

 

 

: A B C D E F G H I J K L M N

 

 

 

 

 

 

SERIAL NO.: Displays the serial number of the product LOT/DATE: Displays the manufacturing control number HOUR METER: Displays the conduction time for the product

TEMPERATURE: Displays the outside air temperature that is measured by a temperature sensor located in the product

Other items: Displays the settings in the integrator mode

Note

When the displayed temperature is high, the panel shuts down. However, the display itself should always be used as an indicator.

99

Normal Operating Mode

4 Volume Adjustment/Muting

Pressing the [VOLUME+] button on the remote control or main-control panel raises the volume.

Pressing the [VOLUME-] button on the remote control or main-control panel lowers the volume.

Pressing the [MUTING] button on the remote control switches between no sound (muting ON) and sound (muting OFF) each time the button is pressed.

Note

Muting is cleared when the power is turn OFF.

5 Auto screen adjustment

Pressing the [AUTO SET UP] button on the remote control or main-control panel during PC signal input causes the

‘SCREEN’ in the menu mode to adjust automatically. If a multi screen is being used, only the main screen can be adjusted.

Note

Adjustment cannot be performed from INPUT2.

Adjustment cannot be performed well when the input signal is a low brightness signal such as black, or is showing movement.

Automatic SCREEN adjustment values are reflected under ‘SCREEN’ in the menu mode.

6 Point Zoom (only when using the remote control)

• Pressing the [POINT ZOOM] button on the remote control designates the POINT ZOOM screen. Each time the button is pressed, the magnification rate changes as shown below.

 

3 LEVEL1

 

3 LEVEL2

 

 

 

 

 

 

 

LEVEL4 2

 

LEVEL3 2

 

 

 

 

During magnification, it is possible to scroll the display position using the [5/∞/2/3] buttons on the remote control.

7 Multi screen (only when using the remote control)

• Pressing the [SPLIT] button on the remote control designates a multi screen. Each time the button is pressed, the screen changes as shown below.

3 Side-by-side

OFF 2

Picture-in-picture 2

When input is switched during a multi-screen display, input of the main screen is switched.

When the [SUB INPUT] button on the remote control is pressed during a multi-screen display, the input of the sub screen is switched.

When the [SWAP] button on the remote control is pressed during a multi-screen display, the main screen and sub screen are switched.

Press the [2/3] buttons on the remote control during multi-screen mode to change the sound on the main screen and the subscreen. This overrides last memory.

When the [PIP SHIFT] button on the remote control is pressed during a PinP screen display, the display position of the sub screen changes as shown below.

 

3 Lower right

3 Upper right

 

 

 

 

 

 

 

 

 

 

 

Lower left 2

 

 

Upper left 2

 

 

 

 

 

 

Note

For the setting of size and layout for Side-by-side and for the size of Picture-in-picture, refer to “Integrator Mode” (pg. 177).

8 Some other RS-232C commands besides those described above are also effective. For details, refer to section 5.5, “RS-232C Adjustment” (pg. 189).

Note

Same function display is possible for main input and sub input. However, during circuit processing, since the highimage quality circuit is used for the main input, the screen looks different on the sub screen.

While the video wall is set, multi-screen display is unavailable.

When the video wall is set or during multi-screen display, point zoom is unavailable.

100