Pioneer FH-X730BS, FH-X731BT, FH-X830BHS Owner's Manual

English Français Español

CD RDS RECEIVER

AUTORADIO CD RDS

REPRODUCTOR DE CD CON RECEPTOR RDS

FH-X830BHS

FH-X730BS

FH-X731BT

Owner’s Manual

Mode d’emploi

Manual de instrucciones

Important (Serial number)

The serial number is located on the bottom of th is unit. For your own se curity and

convenience, be sure to record this number on the enclosed warranty card.

Important (Numéro de série)

Le numéro de série se trouve au bas de cet appareil. Pour votre sécurité et votre commodité,

veillez à noter ce numéro sur la carte de garantie fournie.

Importante (Número de serie)

El número de se rie se encuentra en la pa rte inferior de esta unidad. Por su propia seguri dad

y comodidad, asegúrese de anotar este número en la tarjeta de garantía que se adjunta.

2En

Before You Start....................................................................................... 2

Getting Started........................................................................................ 3

HD Radio™ Technology/Radio .............................................................. 6

CD/USB/iPod/AUX................................................................................... 7

Bluetooth.................................................................................................. 9

App Mode............................................................................................... 12

Pandora®................................................................................................. 12

Spotify®................................................................................................... 13

SiriusXM Satellite Radio....................................................................... 14

Using Pioneer ARC APP........................................................................ 16

Audio adjustments ............................................................................... 17

Settings................................................................................................... 17

FUNCTION settings .............................................................................. 18

AUDIO settings...................................................................................... 19

SYSTEM settings ................................................................................... 20

ILLUMINATION settings ....................................................................... 21

MIXTRAX settings................................................................................. 22

Connections/Installation..................................................................... 23

Additional Information........................................................................ 25

About this manual:

• In the following instructions, a USB memory or USB audio player are referred to as

“USB device”.

• In this manual, iPod and iPhone are referred to as “iPod”.

Table of Contents

Thank you for purchasing this PIONEER product

To ensure proper use, please read through this manual before using this product. It is especially

important that you read an d observe WARNI NGs and CAUTIONs in this manual. Please keep the

manual in a safe and accessible place for future reference.

The Safety of Your Ears is in Your Hands

Get the most out of your equipment by playing it at a safe level—a level that lets the sound come

through cle arly without annoyin g blaring or disto rtion and, most im portantly, without a ffecting your

sensitive hearing. Sound can be deceiving.

Before You Start

FCC ID: AJDK071

MODEL NO.: FH-X830BHS/FH-X730BS/FH-X731BT

IC: 775E-K071

This device complies with Part 15 of FCC Rules and Industry Canada licence-exempt RSS standard(s ).

Operation is subject to the following two conditions: (1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired

operation of this device.

This transmitter must not be co-located or operated in conjunction with any other antenna or

transmitter.

The Bluetooth antenna cannot be removed (or replaced) by user.

This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled

environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to

OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels

of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). But

it is desirable that it should be installed and operated keeping the radiator at least 20cm or more

away from person’s body (excluding extremities: hands, wrists, feet and ankles).

Alteration or modifications carr ied out without ap propriate authoriza tion may invalidate the user’s

right to operate the equipment.

Note

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

–Reorient or relocate the receiving antenna.

–Increase the separation between the equipment and receiver.

–Connect the equipment in to an outlet on a circuit different from that to whic h the receiver is

connected.

–Consult the dealer or an experienced radio/TV technician for help.

3En

English

Over time, your hearing “comfort level” adapts to higher volumes of sound, so what sounds “normal”

can actually be loud and harmful to your hearing. Guard against this by setting your equipment at a

safe level BEFORE your hearing adapts.

ESTABLISH A SAFE LEVEL:

• Set your volume control at a low setting.

• Slowly increase the sound until you can hear it comfortably and clearly, without distortion.

• Once you have established a comfortable sound level, set the dial and leave it there.

BE SURE TO OBSERVE THE FOLLOWING GUIDELIN ES:

• Do not turn up the volume so hi gh that you can’t hear what’s around you.

• Use caution or temporarily di scontinue use in potentially ha zardous situations.

• Do not use headphones while operating a motorized vehicle; the use of headphones may create a

traffic hazard and is illegal in many areas.

WARNING

• Do not attempt to install or service this product by yourself. Installation or servicing of this

product by persons without training and experience in el ectronic equipment and automotive

accessories may be dangerous a nd could expose you t o the risk of elec tric shock, in jury or other

hazards.

• Do not attempt to operate the uni t while driving. Make sure to pull off the road and park your vehicle

in a safe location before attempting to use the controls on the device.

• This product contains chemicals known to the State of California and other governmental entities to

cause cancer and birth de fects or other reproductive harm. Wash hands after handling.

CAUTION

• Do not allow this unit to come into contact with moisture and/or liquids. Electrical shock could result.

Also, damage to this unit, smoke, and overheating could result from contact with liquids.

• Always keep the volume low enough to hear outside sounds.

• This product is evaluated in moderate and tropical climate condition under the Audio, video and

similar electronic apparatus - Safety requirements, IEC 60065.

After-sales service for Pioneer products

Please contact the dealer, distributor from where you purchased this unit or the authorized PIONEER

Service Station for after-sales se rvice or any other information. In case the necessary i nformation is not

available, please contact the companies listed below:

Please do not ship your unit to the companies at the addresses listed below for repair without

contacting them in advance.

CAUTION:

USE OF CONTROL OR ADJUSTMENT OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE

SPECIFIED HEREIN MAY RESULT IN HAZARDOUS R ADIATION EXPOSURE.

CAUTION:

THE USE OF OPTIC AL INSTRUMENTS WITH THIS PRODUCT WIL L INCREASE EYE HAZARD.

CAUTION

This product is a class 1 laser product classified under the Safety of laser products, IEC 60825-1:2007.

For warranty information please see the Limited Warranty sheet included with this unit.

FH-X830BHS/X730BS/X731BT

U.S.A. and CANADA

Pioneer Electronics (USA) Inc.

CUSTOMER SUPPORT DIVISION

P.O. Box 1760

Long Beach, CA 90801-1760

800-421-1404

Getting Started

Basic operation

SRC (source)/OFF

Display window

M.C. (multi-control) dial

BAND/

DISP (display)

4En

Remote Control

Frequently used operations

The available buttons vary depending on the unit.

* When this unit’s blue/wh ite lead is connected to the vehicl e’s auto-antenna relay control terminal,

the vehicle’s antenn a extends when this unit’s source is turned on. To retract the anten na, turn the

source off.

Purpose

Operation

Head Unit Remote Control

Turn on the power* Press SRC/OFF to turn on

the power.

Press and hold SRC/OFF to

turn off the power.

Press SRC to turn on the

power.

Press and hold SRC to turn

off the power.

Adjust the volume Turn the M.C. dial. Press VOLUME + or –.

Press MUTE to mute the

unit. Press again to unmute.

Select a source Press SRC/OFF repeatedly. Press SRC repeatedly.

Change the display

information

Press DISP repeatedly. Press DISP repeatedly.

Return to th e previous

display/list

Press BAND/ . Press / to select the

next/previous folder.

Return to the normal display

from the menu

Press and hold BAND / .

–

Answering a call Press . Press .

Ending a call Press . Press .

/

SRC (source)

VOLUME +/–

MUTE

DISP (display)

Display indication

The microprocessor must be reset in the following situations:

– Before using this unit for the first time after installation

– If the unit fails to operate properly

– When strange or incorrect messages appear on the display

1 Press the RESET button with a pen tip or other pointed instrument.

Indication Description

Appears when a lower tier of the menu or folder exists.

Appears when a Bluetooth telephone is connected to this unit by HFP

(Hands Free Profile) (page 9) and flashes while the telephone is on hold.

Appears when a Bluetooth audio player is connected to this unit by A2DP

(Advanced Audi o Distribution Profile) (page 9).

Appears when the button is pressed.

Appears when the sound retriever function is set (page18).

Appears when random/shuffle play is set (except when BT AUDIO is

selected as the source).

Appears when repeat play is set (except when BT AUDIO is selected as the

source).

Appears when the iPod control function is set (page 9).

Appears when a Bluetooth connection is made (page 9).

Resetting the microprocessor

RESET button

5En

English

Remove the insulation sheet before use.

WAR NING

• Do not ingest the battery, Chemical Burn Hazard.

• This product, including the supplied remote control, contains a coin/button cell battery. If the coin/

button cell battery is swallowed, it can cause severe internal burns in just two hours and can lead to

death.

• Keep new or used batteries out of the reach of children. If the battery is swallowed or placed inside

any part of the bo dy, consult a doctor immediately.

• If the battery compartment does not close securely, stop using the product and keep it away from

children.

• Do not expose the battery or remote control to excessive heat such as direct sunlight or fire.

CAUTION

• There is a potential danger of explosion if the battery is incorrectly replaced. When replacing the

battery, replace it with the same type.

• Do not handle or store the battery with metallic tools or objects.

• If the battery leaks, remove the battery and wipe the remote control completely clean. Then install a

new batter y.

• When disposing of used batteries, please comply with governmental regulations or environmental

public instit utions’ rules that apply in you r country/area.

• “Perchlorate Ma terial - special hand ling may apply.

See www.dtsc.ca.gov/hazardouswaste/perchlorate. (Applicable to California, U.S.A.)”

Important

• Do not store the remote control in high temperatures or direct sunlight.

• Do not let the remote control fall onto the floor, where it may become jammed under the brake or

accelerator pedal.

Preparing the remote control

How to replace the battery

Insert the CR2025 (3 V ) battery with the plus (+) and

minus (–) poles orientated properly.

When you turn the ignition switch to ON after installation, the setup menu appears in

the display.

WAR NING

Do not use the unit in standard mode when a speaker system for network mode is connected to the

unit. Do not use the unit in network mode when a speaker system for standard mode is connected to

the unit. This may cause damage to the speakers.

1 Turn t he M.C. dial to select the options, then press to confirm.

To proceed to the next menu option, you need to confirm your selection.

2 [QUIT :YES] appears when all the settings have been made.

To return to the first item of the setup menu, tur n the M.C. dial to select [QUIT :NO],

then press to confirm.

3 Press the M.C. dial to confirm the settings.

NOTE

[CLOCK SET] can be mad e at any time. See page 20 for more detai ls.

1 Press the M.C. dial to display the main menu.

2 Turn t he M.C. dial to select [SYSTEM], then press to confirm.

Setup menu

Menu Item Description

CLOCK SET Set the clock.

1 Tur n the M.C. dial to adjust the hour, then press to confirm.

The indicator moves to the minute setting automatically.

2 Tur n the M.C. dial to adjust the minute, then press to confirm.

SPEAKER MODE Switch between two operation modes: the 2-way network mode

(NETWORK) and the standard mode (STANDARD) according to

the connections you have established. For details on operation

modes, see page 17.

After selecting the appropriate mode, turn the M.C. dial to

select [YES], then press to confirm.

• You cannot complete the setup menu without setting the

[SPEAKER MODE].

• Once the speaker mode is set, this setting cannot be changed

unless the defa ult settings of this produc t are restored. Restore

the default settings to change the speaker mode setting (refer

to SYSTEM RESET on page 6).

[STANDARD],

[NETWORK]

Canceling the demonstration display (DEMO OFF)

6En

3 Turn the M.C. dial to select [DEMO OFF], then press to confirm.

4 Turn the M.C. dial to select [YES], then press to confirm.

1 Press and hold SRC/OFF until the unit turns off.

2 Press the M.C. dial to display the main menu.

3 Turn the M.C. dial to select [INITIAL], then press to confirm.

4 Turn the M.C. dial to select an option, then press to confirm.

NOTE

The options v ary depending on t he unit.

INITIAL settings

Menu Item Description

REAR-SP Select when there is a full-range speaker connected to the rear

speaker output leads.

[FUL]

[SW] Select when there is a subwoofer connected directly to the rear

speaker output leads without any auxiliary amplifier.

SYSTEM UPDATE Select [SYSTEM INFO] to confirm the latest system information

on the unit.

Select [S/W UPDATE] to update the unit to the lates t software

and initialize the unit settings. For details on the latest software

and updating, visit our website.

[SYSTEM INFO], [S/

W UPDATE]

SXM RESET Select to initialize the SiriusXM settings.

[YES], [CANCEL]

SYSTEM RESET Select [YES] to initialize the unit settings. The unit will be

restarted automatically.

(Some of the settings may be retained even after resetting the

unit.)

[YES], [CANCEL]

(HD Radio™ Technology is only available for FH-X830BHS.)

(Radio is only available for FH-X730BS/X731BT.)

The tuner frequencies on this unit are allocated for use in North America. Use in other

areas may result in poor reception.

About HD Radio™ stations

HD Radio™ stations offer high-quality audio and data services. HD Radio stations are

brought to you by local FM/AM stations.

HD Radio stations feature the following:

– High quality audio

–FM multicasting

–Data services

Program Service Data: Contributes to the superior user experience of HD Radio

Technology. Presents song name, artist, station IDs, HD2/HD3 Channel Guide, and other

relevant data s treams.

Adjacent to traditional main stations are extra local FM channels. These HD2/HD3

Channels provide new, original music as well as deep cuts into traditional genre.

HD Radio™ Technology/Radio

Analog AM Digital AM

Analog FM

Analog FM

Analog FM

Digital FM-1 ch

Digital FM-2 ch

Digital FM-3 ch

Digital FM

FM band

Analog AM

AM band

7En

English

Digital, CD-quality sound. HD Radio Technology enables local radio stations to broadcast

a clean digital signal. AM sounds like today’s FM and FM sounds like a CD.

1 Press SRC/OFF to select [HD RADIO] or [RADIO].

2 Press BAND/ to select the band from [FM1], [FM2], [FM3] or [AM].

3 Press a number button (1/ to 6/).

NOTE

You can select a preset channel by pressing and turning the M.C. dial.

TIP

The / buttons can be also used to select a preset station when [SEEK] is set to [PCH] in the

FUNCTION settings (page18).

The six strongest stations are stored on the number buttons (1/ to 6/).

1 After selecting the band, press the M.C. dial to display the main menu.

2 Turn t he M.C. dial to select [FUNCTION], then press to confirm.

3 Turn t he M.C. dial to select [BSM], then press to confirm.

To seek a station manually

1

After selecting the band, press / to select a station.

Press and hold / then release to seek an available station. Scanning stops

when the unit receives a station. To cancel seek tuning, press / .

NOTES

• [SEEK] needs to be set to [MAN] in the FUNCTION settings (page 18).

• Depending on the reception status, seek tuning can be changed between digital station seek and all

station seek (page 18) (only for FH-X830BHS).

To store stations manually

1

While receiving the station you want to store, press and hold one of the number

buttons (1/ to 6/ ) until it stops flashing.

NOTE

You can select a preset channel by pressing and turning the M.C. dial. After selecting a channel,

press and hold the M.C. dial to store a station.

Receiving preset stations

Best stations memory (BSM)

(Only for FH-X830BHS)

1 While receiving an emergency announcement, press .

The last four items that have been received appear.

2 Turn t he M.C. dial to select one of the items, then press to confirm.

The detail of the selected item appears.

NOTE

[/TEST/] appears at the beginning of an item if it was a test message.

To delete an alert history

1

Press and hold the M.C. dial in step 2 above.

2 Tur n the M.C. dial to select [DELETE YES], then press to confirm.

Disconnect headphones from the device before connecting it to the unit.

Alert history

CD/USB/iPod/AUX

Playing back

AUX input jack (3.5 mm stereo jack)

(eject)

Disc loading slot

USB port

SRC (source)/OFF

M.C. (multi-control) dial

8En

CD

1

Insert a disc into the disc loading slot with the label side up.

To eject a disc, stop playback first then press .

USB devices (including Android™)/iPod

1 Open the USB port cover.

2 Plug in the USB device/iPod using an appropriate cable.

NOTE

To automatically switch to [USB] source when a USB device/iPod is connected to the unit, set [USB

AUTO] to [ON] in the SYSTEM settings (page 21).

CAUTION

Use an optional Pioneer USB cable (CD-U50E) to connect the USB device as any device connected

directly to the unit will protrude out from the unit, which could be dangerous.

Before removing the device, stop playback.

AOA connections

For details on AOA connection, see page 16.

MTP connection

A device installed with Android OS 4.0 or later can be connected to the unit via MTP, using the cable

supplied with the device. However, dep ending on the connected device and the numbers of the files in

the device, audi o files/songs may not be able to be played back vi a MTP. Note that MTP connection is

not compatible with WAV file formats and FLAC file formats, and cannot be used with the MIXTRAX

function.

NOTE

If you use an MTP connection, [ANDROID WIRED] needs to be set to [MEMORY] in the SYSTEM settings

(page 21).

AUX

1

Insert the stereo mini plug into the AUX input jack.

2 Press SRC /OFF to select [AUX] as the source.

NOTE

If [AUX] is set to [OFF] in the SYSTEM settings, [AUX] cannot be selected as a source (page 21).

You can make various adjustments in the FUNCTION settings (page 18).

Note that the following operations do not work for an AUX device. To operate an AUX

device, use the device itself.

Operations

*1 Compressed audio files only

*2 When you use the fast forwa rd or reverse func tion while playing a VBR file, the pl ayback time may

be not correct.

Purpose Operation

Select a folder/album*1 Press 1/ or 2/.

Select a track/song (chapter) Press or .

Fast forward or reverse*2 Press and hold or .

Search for a file from a list 1 Press to display the list.

2 Tur n the M.C. dial to select the desired

file (folder) name or category, then press

to confirm.

3 Tur n the M.C. dial to select the desired

file, then press to confirm.

Playback starts.

View a list of the files in the selected folder/

category*1

Press the M.C. dial when a folder/category

is selected.

Play a song in the selected folder/

category*1

Press and hold the M.C. dial when a folder/

category is selected.

Alphabetical search (iPod only) 1 Press to display the list.

2 Tur n the M.C. dial to select the desired

category list, then press to enter the

alphabetical search mode.

(Turning the M.C. dial twice also enters

the alphabetical search mode.)

3 Tur n the M.C. dial to se lect a letter, then

press to display the alphabetical list.

To cancel alphabetical search, press BAND/

.

Repeat play Press 6/.

Random/shuffle play Press 5/.

Shuffle all play (iPod only) Press and hold 5/.

Pause/resume playback Press 4/PAUS E.

Return to root folder (CD/USB only)*1 Press and hold .

Switch between compressed audio and CD-

DA (CD only)

Press BAND/.

9En

English

Link play mode

You can access songs based on the artist, album, or genre currently playing.

1 While listening to a song, press and hold to enter the link play mode.

2 Tur n the M.C. dial to select the mode ([ARTIST], [ALBUM], [GENRE]), then press to

confirm.

The selected song/album will be played after the currently playing song.

NOTE

The selected song/album may be canceled if you use functions other than those from the link play

mode (e.g. fast forward and reverse).

iPod control

You can control the unit via a connected iPod.

The following iPod models are not compatible with this function.

– iPod nano 1st generation, iPod with video

1 Press BAND/ during playback, then select the control mode.

[CONTR OL iPod]: The unit’s iPod function can be operated from the connected iPod.

[CONTR OL AUDIO]: The unit’s iPod function can only be operated by the buttons on

the unit or supplied remote control. In this mode, the connected iPod cannot be

turned on or off.

NOTES

• Switching the control mode to [CONTROL iPod] pauses song playback. Use the connected iPod to

resume playback.

• The following operations are still accessible from the unit, even if the control mode is set to

[CONTROL iPod].

– Pause, fast forward/reverse, song/chapter selection

• The volume can only be adjusted from the unit.

The MIXTRAX function creates a non-stop mix of your music library, accompanied by

illumination effects. For details on MIXTRAX settings, see page 22.

NOTES

• This function is not compatible with an Android device connected via MTP.

• Depending on the file/song, sound effects may not be available.

• Turn the MIXTRAX function off if the illumination effects it produces interfere with driving.

1 Press 3/MIX to turn MIXTRAX on/off.

Useful functions for iPod

About MIXTRAX (USB/iPod only)

Important

If three or more Bluetooth devices (e.g. a phone and separate audio player) are connected, they may

not work pr operly.

1 Turn on the Bluetooth function of the device.

2 Press to display the phone menu.

3 Turn t he M.C. dial to select [BT SETTING], then press to confirm.

4 Turn t he M.C. dial to select [ADD DEVICE], then press to confirm.

The unit starts to search for available devices, then displays them in the device list.

• To cancel searching, press the M.C. dial.

• If the desired device is not in the list, select [RE-SEARCH].

• If there is no device available, [NOT FOUND] appears in the display.

5 Turn t he M.C. dial to select a device from the device list, then press to confirm.

Press and hold the M.C. dial to switch the displayed device information between the

Bluetooth device address and device name.

6 Select [Pioneer BT Unit] shown in the device display.

7 Make sure the same 6-digit number appears on this unit and the device, then

select “Yes” on the device.

NOTES

• [DEVICE FULL] appears if the unit has already been paired with three other devices. In this case, delete

one of the paired devices. See [DEL DEVICE] or [GUEST MODE] in the Bluetooth settings (page 9).

• Depending on the device, the PIN code is required in step 7. In this case, input [0000].

TIP

The Bluetooth connection can be also made by detecting the unit from the Bluetooth device. To do so,

[VISIBLE] in the Bl uetooth settings needs to b e set to [ON]. For details on a Bluetooth d evice operations,

refer to the operating instructions supplied with the Bluetooth device.

Bluetooth settings

Bluetooth

Bluetooth connection

Menu Item Description

DEVICELIST Display the list of paired Bluetooth devices. “*” appears on the

device name when the Bluetooth connection is established.

10En

First, make a Bluetooth connection with the Bluetooth telephone (page 9). Up to two

Bluetooth telephones can be connected simultaneously.

Important

• Leaving the un it on standby to connect to your pho ne via Bluetooth while the en gine is not running

can drain the vehicle’s battery.

• Be sure to park your vehicle in a safe place and apply the parkin g brake before operati on.

To make a phone call

1

Press to display the phone menu.

When two phones are connected, a phone name appears first then a phone menu

will display. To switch to another phone, press again.

DEL DEVICE Delete the device information.

[DELETE YES],

[DELETE NO]

ADD DEVICE Register a new device.

A.CONN Select [ON] to connect to a Bluetooth device automatically.

[ON], [OFF]

VISIBLE Select [ON] so that a Bluetooth device can detect the unit when

the unit is connected via Bluetooth to another device.

[ON], [OFF]

PIN CODE Change the PIN code.

1 Press the M.C. dial to display the setting mode.

2 Turn the M.C. dial to select a number.

3 Press the M.C. dial to move the cursor to the next position.

4 After inputting the PIN code, press and hold the M.C. dial.

After inputting the PIN code, pressing the M.C. dial returns you

to the PIN code input display, and you can change the PIN code.

DEV. INFO Switch the device information on the display between the

device name and Bluetooth device address.

GUEST MODE Select [ON] to move to the [DEL DEVICE] screen automatically

when the unit has already been paired with three devices.

[ON], [OFF]

A.PAIRING Select [ON] to pair the unit and iPhone automatically when an

iPhone is connected to the unit via USB. ( This function may not

be available depending on the version of iOS you are using.)

[ON], [OFF]

Bluetooth telephone

Menu Item Description

2 Tur n the M.C. dial to select [RECENTS] or [PHONE BOOK], then press to confirm.

If you select [PHONE BOOK], proceed to step 4.

3 Tur n the M.C. dial to select [MISSED], [DIALED] or [RECEIVED], then press to

confirm.

4 Tur n the M.C. dial to select a name or phone number, then press to confirm.

The phone call starts.

To answer an incoming call

1 Press when a call is received.

TIP

When two phones are connected to the unit via Bluetooth and there is an incoming call while one

phone is being used for a call, a message will appear in the display. To answer that incoming call, you

need to end the existing call.

Basic operations

To preset phone numbers

1

Select a phone number from a phone book or call history.

2 Press and hold one of the number buttons (1/ to 6/).

The contact is stored in the selected preset number.

To make a call using a preset number, press one of the numb er buttons (1/ to 6/),

then press the M.C. dial.

Voice recognition (Only for iPhone)

This function is only available when an iPhone equipped with voice recognition is

connected to the unit via Bluetooth.

Purpose Operation

End a call Press .

Reject an incoming call Press and hold when a call is received.

Switch between the current caller

and a caller on hold

Press the M.C. dial.

Cancel a caller on hold Press and hold .

Adjust the volume of the caller’s

voice (When private mode is on,

this function is not available.)

Turn t he M.C. dial during the call.

Turn the privacy mode on or off Press BAND/ during the call.

11En

English

1 Press and hold to activate th e voice recognition mode.

2 Press the M.C. dial and then talk into the microphone to input voice commands.

To exit the voice recognition mode, press BAND/.

NOTE

For details on the voic e recognition features, refer to the manua l supplied wit h your iPhone.

Phone menu

Menu Item Description

RECENTS Display the missed call history.

[MISSED]

[DIALED] Display the dialed call history.

[RECEIVED] Display the received call history.

PHONE BOOK*1 Display the contacts which have been transferred from your

phone. Set [VISIBLE] in the Bluetooth settings to [ON] to browse

the contacts via this unit.

PRESET 1-6 Recall the preset phone numbers. You can also recall the preset

phone numbers by pressing one of the number buttons (1/

to 6/).

A.ANSR*2 Select [ON] to answer an incoming call automatically.

[ON], [OFF]

R.TONE Select [ON] if the ring tone does not come out from the car

speakers. Depending on the connected phone, this fun ction

may not work.

[ON], [OFF]

PB INVT Invert the order of names in the phone book (name view).

PB A.SYNC Select whether or not to transfer the contacts from your phone

automatically when your phone is connected to the unit.

• Whe n connected for the first time, the contacts from your

phone are transferred automatically, regardless of the [PB

A.SYNC] setting.

• If you switch from [ON] to [OFF], the auto synchronization will

not be performed on the next connection.

• If you switch from [OFF] to [ON], the auto synchronization will

be performed when your phone is connected to the unit.

• During the auto synchronization, you cannot cancel the

synchronization, even if you select [OFF].

[ON], [OFF]

BT SET TING You can adjust various settings for Bluetooth connections. For

details on Bluetooth settings, see page 9.

*1 The contacts on your phone will normally be transferred automatically when the phone is

connected. If they are not, use your phone to t ransfer the contac ts.

*2 I f two phones are connected, this function does not work on incoming calls that are received while

one of the phones is being used for a call.

Important

• Depending on the Bluetooth audio player connected to this unit, the available operations will be

limited to the following two levels:

– A2DP (Advanced Audio Di stribution Profile) can only play back s ongs on your audio player.

– AVRCP (Audio/Video Remote Co ntrol Profile) can perform func tions such as playback, pause, s elect

song, etc.

• The sound of the Bluetooth audio player will be muted when the phone is in use.

• When the Bluetoot h audio player is in use, you cannot connect to a Bluetooth telepho ne

automatically.

• Depending on the type of Bluetooth audio player you have connected to this unit, operation and

information displayed may vary based on availability and functionality.

1 Make a Bluetooth connection with the Bluetooth audio player.

2 Press SRC/OFF to select [BT AUDIO] as the source.

3 Press BAND/ to start playback.

Basic operations

You can make various adjustments in the FUNCTION settings (page 18).

* Depending on the connected device, these operations may not be available.

Bluetooth audio

Purpose Operation

Fast forward or reverse Press and hold or .

Select a track Press or .

Repeat play* Press 6/.

Random play* Press 5/.

Pause/resume playback Press 4/PA US E.

Search for a file from a list 1 Press to display a list.

2 Turn the M.C. dial to select the desired

folder name, then press to confirm.

3 Turn the M.C. dial to select the desired

file, then press to confirm.

Playback starts.

12En

You can enjoy listening to an application on an iPhone/Android device via the unit. In

some cases, you can control an application by using the unit.

For details on compatible devices, visit our website.

Important

Use of third part y apps may involve or require the provisio n of personally identifiab le information,

whether through the creation of a us er account or otherwise, and for certain applicat ions, the provision

of geolocation data.

ALL THIRD PARTY APPS ARE THE SOLE RESPONSIBILIT Y OF THE PROVIDERS, INCLUDING WITHOUT

LIMITATION COLLECTION A ND SECURITY OF USER DATA AND PRIVACY PRAC TICES. BY ACCESSIN G

THIRD PARTY APPS, YOU AGREE TO REVIEW THE TERMS OF SERVICE AND PRIVACY POLICIES OF THE

PROVIDERS. IF YOU DO NOT AGREE WITH THE TERMS OR POLICIES OF ANY PROVIDER OR DO NOT

CONSENT TO THE USE OF GEO LOCATION DATA WHERE APPLICA BLE, DO NOT USE THAT THIRD PARTY

APP.

For iPhone users

This function is compatible with iPhones and iPod touches installed with iOS 5.0 or later.

For Android device users

This function is compatible with devices that have Android OS 2.3 or later installed.

NOTE

PIONEER IS NOT LIABLE FOR ANY THIRD PARTY APPS OR CONTENT, INCLUDING WITHOUT LIMITATION

THEIR ACCURACY OR COMPLETENESS. THE CONTENT AND FUNCTIONALITY OF SUCH APPS ARE THE

SOLE RESPONSIBILITY OF THE APP PROVIDER.

1 Connect this unit with the mobile device.

• iPhone via USB (page 8)

• iPhone/Android device via Bluetooth (page 9)

2 Press the M.C. dial to display the main menu.

3 Turn the M.C. dial to select [SYSTEM], then press to confirm.

4 Turn the M.C. dial to select [PHONE CONNECT], then press to confirm.

5 Turn the M.C. dial to select one of the below, then press to confirm.

• Select [IPHONE/IPOD] for iPhone.

• Select [ANDROID] for Android device.

6 Turn the M.C. dial to select one of the below.

• Select [WIRED] for the USB connection.

• Select [BLUETOOTH] for the Bluetooth connection.

App Mode

Playback of an application via the unit

NOTE

When the connec tion setting is changed, a message th at lets you know that the conne ction

setting had been changed will appear in the display. Press the M.C. dial and turn the M.C. dial to

select [SRC OF F :YES], then press to confirm. The unit turns off automaticall y and the setting is

executed.

7 Press SRC/OFF to select [APP].

8 Operate the mobile device to start up the application.

Basic operations

You can make various adjustments in the FUNCTION settings (page 18).

Pandora internet radio is a music service not affiliated with Pioneer. More information is

available at http://www.pandora.com.

The Pandora mobile application is available for iPhone and Android phones. Please visit

www.pandora.com/everywhere/mobile for the latest compatibility information.

Update the firmware of the Pandora application to the latest version before use.

1 Connect this unit with the mobile device.

• iPhone via USB (page 8)

• iPhone/Android device via Bluetooth (page 9)

If you choose a USB connection, proceed to step 6.

2 Press SRC/OFF to select [PANDORA].

3 Press and hold BAND/ to display [PHONE CONNECT].

4 Tur n the M.C. dial to select one of the below, then press to confirm.

• Select [IPHONE/IPOD] for iPhone.

• Select [ANDROID] for Android device.

Purpose Operation

Select a track Press or .

Fast forward or reverse Press and hold or .

Pause/resume playback Press BAND/.

Pandora®

Listening to Pandora

13En

English

5 Turn t he M.C. dial to select [BLUETOOTH] for iPhone/Android device via

Bluetooth.

NOTE

When the connection setting is changed, a message that lets you know that the connection

setting had been changed will appear in the display. Press the M.C. dial and turn the M.C. dial to

select [SRC OFF :YES], then press to confirm. The unit turns off automatically and the setting is

executed.

6 Press SRC/OFF to select [PANDORA].

7 Launch the Pandora application on the mobile device and start playback.

Basic operations

You can make various adjustments in the FUNCTION settings (page 18).

NOTE

Some functi ons of Pandora may not be operated from the unit.

Purpose Operation

Skip a track Press .

Switch between Shuffle and the

station

Press (list), then turn the M.C. dial to select the

Shuffle or the desired station.

Change the sort order Press (list), then select one of the following.

[ABC]: Sort the items in the list alphabetically.

[DATE]: Sort the items in the list in order of the

dates on which the items were created.

Play When Shuffle or the station is selected, press the

M.C. dial.

Delete a station 1 When the station is selected, press and hold the

M.C. dial.

[DELETE YES] appears.

2 Press the M.C. dial.

To cancel, press BAND/ in step 1.

Pause/resume playback Press 4/PAUSE.

Thumbs Up Press 1/.

Thumbs Down Press 2/.

Create a new station based on the

track currently being played

Press and hold 5/.

Create a new station based on the

artist currently being played

Press and hold 6/.

Spotify is a music streaming distribution service not affiliated with Pioneer. More

information is available at http://www.spotify.com.

The Spotify application is available for iPhone and Android phones, please visit https://

support.spotify.com/ for the latest compatibility information.

To enjoy Spotify as you drive, first download the Spotify app to your iPhone or Android

device. You can download it on the iTunes App Store or Google Play™. Choose a free

account or a paid Premium account, either in the app or at spotify.com. A Premium

account gives you more features, like offline listening.

Important

• This product incorporates Spotify software which is subject to 3rd party licenses found here:

www.spotify.com/connect/third- party-licenses.

• For information on the countries and regions where Spotify can be used, take a look at https://

www.spotify.com/us/select-your-country/.

Update the firmware of the Spotify application to the latest version before use.

1 Connect this unit with the mobile device.

• iPhone via USB (page 8)

• iPhone/Android device via Bluetooth (page 9)

If you choose a USB connection, proceed to step 6.

2 Press SRC/OFF to select [SPOTIFY].

3 Press and hold BAND/ to display [PHONE CONNECT].

4 Turn t he M.C. dial to select one of the below, then press to confirm.

• Select [IPHONE/IPOD] for iPhone.

• Select [ANDROID] for Android device.

5 Turn t he M.C. dial to select [BLUETOOTH] for iPhone/Android device via

Bluetooth.

NOTE

When the connection setting is changed, a message that lets you know that the connection

setting had been changed will appear in the display. Press the M.C. dial and turn the M.C. dial to

select [SRC OFF :YES], then press to confirm. The unit turns off automatically and the setting is

executed.

6 Press SRC/OFF to select [SPOTIFY].

7 Launch the Spotify application on the mobile device and start playback.

Spotify®

Listening to Spotify

14En

Basic operations

You can make various adjustments in the FUNCTION settings (page 18).

NOTE

The available operations may vary according to the type of contents (track/album/artist/playlist/radio)

you want to play.

NOTE

Some functions of Spotify may not be operated from the unit.

(Only for FH-X830BHS/X730BS)

Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over

140 channels, including commercial-free music plus the best sports, news, talk, comedy

and entertainment. Welcome to the world of satellite radio. A SiriusXM Vehicle Tuner and

Subscription are required. For more information, visit www.siriusxm.com

Purpose Operation

Skip a track Press or .

Search for a track from a list 1 Press (list) to display the list.

2 Tur n the M.C. dial to select the desired

category, then press to confirm.

3 Tur n the M.C. dial to select the desired

file, then press to confirm.

Playback starts.

Pause/resume playback Press 4/PAUSE.

Thumbs Up (Only for radio) Press 1/.

Thumbs Down (Only for radio) Press 2/.

Random play (Only for track/album/artist/

playlist)

Press 5/.

Repeat play (Only for track/album/artist/

playlist)

Press 6/.

Start a radio channel based on the song

currently being played.

1 Press and hold (list) to start a radio.

2 Press the M.C. dial.

• This function may not be available

depending on the selected song.

SiriusXM Satellite Radio

Replay™

You can pause, rewind or replay live satellite radio as well as the channel you are

currently listening to.

Tun eSta rt™

Automatically start songs from the beginning when you tune to one of your preset

music channels stored on the current band of presets. For details, refer to TUNE START on

page 19.

NOTE

TuneStart is compatible with SXV200 or later tuner models. Not compatible with SXV100.

Tun eSca n™

Scan through short previews of songs you may have missed on music channels stored

on the current band of presets.

Each song in the current channel plays for six seconds at a time.

For details, refer to TUNE SCAN (scanning the songs) on page 19.

NOTE

TuneScan is compatible with SXV200 or later tuner models. Not compatible with SXV100.

Tun eMix ™

Create a music channel that’s a blend of songs made up from the music channels stored

on the current band of presets. For details, refer to TUNEMIX on page 19.

NOTE

TuneMix™ is compatible with the SXV300 or later tuner models. Not compatible with the SXV200 or

SXV100.

1 Press SRC/OFF to select [SIRIUSXM].

2 Press / to select Channel 0.

The Radio ID appears on the display.

In addition, the Radio ID is located on the bottom of the SiriusXM Connect Vehicle

Tun er.

NOTE

The Radio ID does not include the letters I, O, S or F.

3 Activate the SiriusXM service online or by phone.

For U S Subs cript ions:

• Visit www.siriusxm.com/activatenow

• Call SiriusXM Listener Care at 1-866-635-2349

For C anadi an Sub scrip tions :

• Visit www.siriusxm.ca/activatexm

Preparing for the SiriusXM Satellite Radio service

15En

English

• Call 1-877-438-9677

4 [SUBSCRIPTION UPDATED] appears on the display when your SiriusXM Connect

Vehicle Tuner has been subscribed successfully.

Press any key to clear the activation message.

NOTE

The activation process usually takes 10 minutes to 15 minutes but may take up to an hour in some

cases. Do n ot turn off the un it until you clear t he activation mes sage in step 4.

1 Press and hold DISP, then select [CHANNEL].

You can also select the operation mode by the SiriusXM settings (page 19).

2 Press SRC/OFF to select [SIRIUSXM].

3 Press BAND/ to select a band from [SXM1], [SXM2] or [SXM3].

4 Press / to select a channel.

Pressing and holding either button will rapidly browse through the channels.

Press and hold either button then release to tune automatically. Scanning stops

when the unit receives a channel. To cancel seek tuning, press / .

Basic operations

1

Press and hold DISP to select the operation mode [CHANNEL] or [REPLAY].

NOTE

You can exit the replay mode by pressing and holding BAND/.

NOTE

You can also make various adjustments in the SiriusXM settings (page 19).

Listening to a channel

Purpose Operation

Select a channel 1 Set the operation mode to [CHANNEL].

2 Press or .

Pressing and holding either button will

rapidly browse through the channels.

Skip backward/forward 1 Set the operation mode to [REPLAY].

2 Press or .

Fast forward or reverse 1 Set the operation mode to [REPLAY].

2 Press and hold or .

Category scan

The live broadcast for each channel in the current category plays for six seconds at a

time. Follow the instructions below.

To search for a channel from a list

1 Press during playback.

2 Tur n the M.C. dial to select a category.

3 Select one of the operations below.

Category scan: Press and hold the M.C. dial to switch to category scan.

Channel search: Press the M.C. dial to stop a scan.

NOTE

Press DISP to change the display in formation between “Channe l Name”, “Artist Name”, “Song Title”,

“Content Info” and “Ch annel Number”.

Scan options

To preset a channel

1

While receiving a channel you want to store, press and hold one of the number

buttons (1/ to 6/ ) until it stops flashing.

To play the stored channels, select the band and then press a number button (1/ to

6/).

To preset a channel from a list

1

While receiving a channel you want to store, press .

2 Tur n the M.C. dial to select [PRESETS], then press to confirm.

3 Tur n the M.C. dial to select a preset channel.

4 Press and hold the M.C. dial to store.

Purpose Operation

Stopping a scan (selecting the channel or

song playing)

Press the M.C. dial.

Switching to the next/previous song during

TuneS can

Press or .

Switching to the next/previous channel

during the category scan

Press or .

Aborting a scan (The last channel or song

will continue to play when scan ends.)

Press BAN D/.

16En

To receive the stored channels, turn the M.C. dial to select a preset channel, then press

to confirm.

Parental Control

Some SiriusXM channels contain mature content. You can lock these channels. For

details, see [PARENTAL CTRL] in SiriusXM settings (page 19).

You can operate the unit from Pioneer ARC APP installed on an iPhone/Android device.

In some cases, you can control aspects of the application, such as source selection,

pause, etc., by using the unit.

For details on what operations are available on th e application, see the application’s help

section.

WAR NIN G

Do not attempt to op erate the application while dri ving. Make sure to pull off the road and park your

vehicle in a safe location before attempting to use the controls on the application.

For iPhone users

This function is compatible with iPhones (iPhone 5 or later) and iPod touches installed

with iOS 8.0 or later.

You can download Pioneer ARC APP on iTunes App Store.

For Android device users

This function is compatible with devices that have Android OS 4.1 or later installed and

also support AOA (Android Open Accessory) 2.0.

You can download Pioneer ARC APP on Google Play.

NOTE

Some Android devices connected via AOA 2.0 may not work properly or emit sounds due to their own

software design, regardless of the OS version.

1 Connect this unit with the mobile device.

• iPhone/Android device via USB (page 8)

• iPhone/Android device via Bluetooth (page 9)

2 Press the M.C. dial to display the main menu.

3 Turn the M.C. dial to select [SYSTEM], then press to confirm.

Using Pioneer ARC APP

Making a connection with Pioneer ARC APP

4 Tur n the M.C. dial to select [PHONE CONNECT], then press to confirm.

5 Tur n the M.C. dial to select one of the below, then press to confirm.

• Select [IPHONE/IPOD] for iPhone.

• Select [ANDROID] for Android device.

6 Tur n the M.C. dial to select one of the below.

• Select [WIRED] for the USB connection.

• Select [BLUETOOTH] for the Bluetooth connection.

Proceed to step 10 if you select the USB connection for iPhone or the Bluetooth

connec tion.

NOTE

When the connec tion setting is changed, a message th at lets you know that the conne ction

setting had been changed will appear in the display. Press the M.C. dial and turn the M.C. dial to

select [SRC OF F :YES], then press to confirm. The unit turns off automaticall y and the setting is

executed.

7 Repeat steps 2 to 3.

8 Tur n the M.C. dial to select [ANDROID WIRED], then press to confirm.

9 Tur n the M.C. dial to select [APP CONTROL] for an Android device connected via

USB.

If [ON] is selected in [P.APP AUTO ON] (page 21), Pioneer ARC APP on the Android

device starts automatically, and all the steps are finished.

NOTE

If Pioneer ARC APP has not been installed on your Android device yet, a message that prompts you

to install the application will appear on your Android device. Select [OFF] in [P.APP AUTO ON] to

clear the message (page 21).

10 Press SRC/OFF to select any source.

11 Launch Pioneer ARC APP on the mobile device.

NOTE

You can also launch the application by pressing and holding the M.C. dial if you select the USB

connection for iPhone or the Bluetooth connection.

1 Press SRC/OFF to select [ANDROID].

Listening to music on Android

17En

English

Basic operations

You can also make various adjustments in the AUDIO settings (page 19).

This unit features two operation modes: network mode and standard mode. You can

switch between modes as desired (page 5).

Network mode

You can create a 2-way + SW multi-amp and multi-speaker system with high range

speaker, middle range speaker and subwoofer for reproduction of high, middle and low

frequencies (bands).

Standard mode

You can create a 4-speaker system with front and rear speakers or front speakers and

subwoofers, or a 6-speaker system with front and rear speakers and subwoofers.

You can adjust the cut-off frequency value and the slope value of each speaker.

The following speakers can be adjusted.

Network mode:

[HIGH] (high-range speaker HPF), [MID HPF] (middle-range speaker HPF), [MID LPF]

(middle-range speaker LPF), [SUBWOOFER]

Standard mode:

[FRONT], [REAR], [SUBWOOFER]

NOTE

[SUBWOOFER] can only be selected when [ON] is selected in [SUBWOOFER] (page 20).

1 Press the M.C. dial to display the main menu.

Purpose Operation

Select a track Press or .

Fast forward or reverse Press and hold or .

Pause/resume playback Press 4/PAU SE .

Audio adjustments

Operation modes

Adjusting the cut-off frequency value and the slope

value

2 Turn t he M.C. dial to select [AUDIO], then press to confirm.

3 Turn t he M.C. dial to select [CROSSOVER], then press to confirm.

4 Turn t he M.C. dial to select the speaker unit (filter) to be adjusted, then press to

confir m.

5 Turn t he M.C. dial to select [HPF] or [LPF] according to the speaker unit (filter),

then press to confirm.

6 Turn t he M.C. dial to select an appropriate cut-off frequency for the speaker unit

(filter) selected in step 4, then press to confirm.

Network mode:

[1.25K] to [12.5K] (if you choose [HIGH] or [MID LPF])

[25] to [250] (if you choose [MID HPF] or [SUBWOOFER])

Standard mode:

[50HZ] to [200HZ]

7 Turn t he M.C. dial to select an appropriate slope for the speaker unit (filter)

selected in step 4.

Network mode:

[–6] to [–24] (if you choose [HIGH], [MID HPF] or [MID LPF])

[–12] to [–36] (if you choose [SUBWOOFER])

Standard mode:

[–6] to [–24]

You can adjust various settings in the main menu.

1 Press the M.C. dial to display the main menu.

2 Turn t he M.C. dial to select one of the categories below, then press to confirm.

• FUNCTION settings (page 18)

• AU DIO settings (page 19)

• SYSTEM settings (page 20)

• ILLUMINATION settings (page 21)

• MIXTRAX settings (page 22)

3 Turn t he M.C. dial to select the options, then press to confirm.

Settings

18En

The menu items vary according to the source.

is only available for FH-X830BHS.

FUNCTION settings

Menu Item Description

BSM

Store the six strongest stations on the number

buttons (1/ to 6/) automatically.

LOC AL

FM: [OFF], [LV1], [LV2], [LV3], [LV4]

AM: [OFF], [LV1], [LV2]

Restrict the tuning station according to the

signal strength.

SEEK

[MAN], [PCH] Assign or buttons to seek the stations

one by one (manual tuning) or select a station

from the preset channels.

HD SEEK*

[ON], [OFF] Change seek tuning setting between digital

station seek ([ON]) and all station seek ([OFF])

depending on the reception status.

BLEND*

[ON], [OFF] Set [ON] to switch to the analog broadcast of the

same frequency level automatically if a digital

broadcast reception is poor. Set [OFF] to receive

analog broadcast only.

SAVE

Store the information about the song currently

being played to your music list on Spotify.

UNSAVE

Remove the song information stored in [SAVE].

SEL DEVICE

Connect a Bluetooth device in the list.

iPod

* If [HD SEEK] is set to [ON] and [BLEND ] is set to [OFF], the tuner canno t receive broadcasts. In this

case, [HD SEEK] or [BLEND] i s changed aut omatically as follows:

– When [HD SEEK] is set to [ON], if you switch [BLEND] from [ON] to [O FF], [HD SEEK] is changed to

[OFF].

– When [BLEND] is set to [OFF], if you switch [HD SEEK] from [OFF] to [ON ], [BLEND] is changed to

[ON].

ACTI VE RADI O

[ON], [OFF] Interrupt the currently selected source with

emergency announcements or test messages. A

beep can be heard when an emergency

announcement or test message breaks in. Select

[OFF] to disable this function. (In some cases

when a test message is received, a notification

will appear in the display instead of a beep.)

S.RTRV

[1] (effective for low compression

rates),

[2] (effective for high

compression rates),

[OFF]

Enhance compressed audio and restore rich

sound.

AUDIO BOOK

[FASTER], [NORMAL], [SLOWER] Change the playback speed. (Not available when

[CONTROL iPod] is selected in the control mode.)

BOOKMARK

Store the track information currently being

played in your Pandora account.

NEW STATION

[FROM TRACK], [FROM ARTIST] Create a new station based on the track or artist

currently being played.

PAUS E

Pause or resume playback.

PLAY

Start playback.

STOP

Stop playback.

Menu Item Description

USB

iPod

AUX

iPod

19En

English

SiriusXM settings

SiriusXM is only available for FH-X830BHS/X730BS.

Menu Item Description

PAU SE

Pause or resume playback.

OPERATE MODE

[CHANNEL], [REPLAY] Assign or buttons to select a channel

or skip backward/skip forward.

TUNEMIX

[ON], [OFF] Create a music channel that’s a blend of songs

made up from the music channels stored on the

current band of presets.

TUNE SCAN

Scan through songs from your music channel

presets.

TUNE START

[ON], [OFF] Start playback of the broadcast from the

beginning of a song when tuning to a preset

music channel.

PAR ENTA L CT RL

[LOCKED CH], [CLEAR ALL], [EDIT

CODE]

Input the current passcode on the [PASSCODE]

screen (the default passcode is 0000).

1 Turn t he M.C. dial to select a number.

2 Press the M.C. dial to move the cursor to the

next position.

3 After inputting the passcode, press the M.C.

dial.

4 Turn t he M.C. dial to select one of the

following menu items, then press to confi rm.

• [LOCKED CH]: Lock the current channel, which

contains mature content.

1 Press the M.C. dial to turn the lock on or off.

• [CLEAR ALL]: Unlock all the channels that have

restricted access.

1 Turn t he M.C. dial to switch to [YES], then

press to confirm.

• [EDIT CODE]: Change the passcode.

1 Repeat steps 1 to 3 to enter a new passcode.

2 After inputting the passcode, press the M.C.

dial.

The new passcode is saved.

AUDIO settings

Menu Item Description

EQ SETTING

[SUPER BASS], [POWERFUL],

[NATURAL], [VOCAL], [CUSTOM1],

[CUSTOM2], [FLAT]

Select an equalizer band and

level for further customizing.

Equalizer band: [50HZ] to

[12.5kHZ]

Equalizer l evel: [–6] to [+6]

Select or customize the equalizer curve.

• When you select a setting other than

[CUSTOM1] and [CUSTOM2], you can also

customize the equalizer curve by pressing and

holding the M.C. dial, then store the

customized equalizer curve in [CUSTOM1].

FAD ER *1 (Only for standard mode)

Adjust the front and rear speaker balance.

BALANCE

Adjust the left and right speaker balance.

Menu Item Description

20En

SUBWOOFER

[ON], [OFF] Set to [ON] when using a subwoofer speaker.

SUBWOOFER*2

[NOR], [REV] Select the subwoofer phase.

SPEAKER LEVEL

Network mode: [HIGH L], [HIGH

R], [MID L], [MID R], [SUBWOOFER]

Standard mode: [FRONT L],

[FRONT R], [REAR L], [REAR R],

[SUBWOOFER]

Output level: [–24] to [10]

Select a speaker unit (filter) and adjust the

output level.

• Each value you have adjusted changes when

you change the [POSITION] setting (page 20).

CROSSOVER

Select a speaker unit (filter) to adjust the HPF or

LPF cut-off frequency and the slope for each

speaker unit.

For details on the [CROSSOVER] setting, see

page 17.

POSITION

[OFF], [FRONT LEFT] (front seat

left), [FRONT RIGHT] (front seat

right), [FRONT] (front seats), [ALL]*

* Only for sta ndard mode

Select a listening posit ion to adjust the speakers'

output levels automatically and add a delay time

that corresponds to the number and locations of

occupied seats.

TIME ALGNMNT

[INITIAL], [OFF], [CUSTOM]

Select a type of speaker and

adjust the speaker distance for

further customizing in [CUSTOM].

Network mode: [HIGH L], [HIGH

R], [MID L], [MID R], [SUBWOOFER]

Standard mode: [FRONT L],

[FRONT R], [REAR L], [REAR R],

[SUBWOOFER]

Speaker distance (inch): [140] to

[0]

Select or customize the time alignment settings

to reflect the distance between the listener’s

position and each speaker.

• Select [INITIAL] to initialize the setting value.

• Select [OFF] to reset all setting values to 0.

• The [CUSTOM] setting is available when

[FRONT LEFT] or [FRONT RIGHT] is selected in

[POSITION] ( page 20).

• The [CUSTOM] setting is not available when

[OFF] is selected in [SUBWOOFER] (page 20).

Menu Item Description

*1 Not available when [SW] is selected in [REAR-SP] in the INITIAL settings (page 6).

*2 Not available when [FUL] is selected in [REAR-SP] in the INITIAL settings (page 6).

You can also access to these menus when the unit is turned off.

SAVE SETTINGS

[YES], [CANCEL] Save to later recall the following sound settings

at their current values: [CROSSOVER], [SPEAKER

LEVEL], [EQ SETTING], [POSITION], [TIME

ALGNMNT], [BASS BOOST], [SUBWOOFER].

LOAD SET TING S

Load the sound settings, when you have already

performed [SAVE SETTINGS].

BASS BOOST

[0] to [+6] Select the bass boost level.

LOU DNES S

[OFF], [LOW], [MID], [HI] Compensate for clear sound at low volume.

AUTO LV C TRL

[OFF], [MODE1], [MODE2] Adjust the difference in volume levels among

sources or audio files automatically.

SLA

[+4] to [–4] Adjust the volume level for each source except

FM.

Each of the below combinations are set to the

same setting automatica lly.

• When making a USB connection, set USB, iPod,

PANDORA, ANDROID, SPOTIFY, and APP.

• W hen making a Bluetooth connection, set BT

AUDIO, iPod, PANDORA, ANDROID, SPOTIFY,

and APP.

SYSTEM settings

Menu Item Description

CLOCK SET

Set the clock (page 5).

12H/24H

[12H], [24H] Select the time notation.

Menu Item Description

21En

English

BEEP TONE

[ON], [OFF] A beep can be heard when any button is pushed.

Select [OFF] to disable this function.

INFO DISPLAY

[SOURCE/BTINFO], [SOURCE/

SPEANA], [CLOCK/BTINFO],

[CLOCK/SPEANA], [LEVEL METER],

[SPEANA], [OFF]

Display the item on the sub information display.

• When [SO URCE/SPEANA] or [CLOCK/SPEANA] is

selected, display the antenna instead of the

speana on the radio source.

DOT DISPLAY

[SPEANA], [ICON] Select [SPEANA] or [ICON] to appear on the left

side of the display.

AUX

[ON], [OFF] Set to [ON] when using an auxiliary device

connected to the unit.

BT AUDIO

[ON], [OFF] Set the Bluetooth signal on/off.

SPOTIFY

[ON], [OFF] Set to [ON] when using the Spotify function.

BT MEM CL EAR

[YES], [CANCEL] Clear the Bluetooth device data (device list, PIN

code, call history, phone book, preset phone

numbers) stored in the unit.

[CLEARED] appears when data is successfully

deleted.

PHONE CONNECT

[IPHONE/IPOD], [ANDROID] Select the type of device ([IPHONE/IPOD] or

[ANDROID]) and the appropriate connection

method ([WIRED] or [BLUETOOTH]) according to

your device.

• When [BLUETOOTH] is selected, USB

connections cannot be made regardless of the

current Bluetooth connection to the unit.

• Select [ANDROID] when you connect the

mobile device other than iPhone or Android.

• When the setting is changed, [USB AUTO]

(page 21) is automatically performed if [USB

AUTO] is set to [ON].

Menu Item Description

ANDROID WIRED

[MEMORY], [APP CONTROL] Select the appropriate connection method for an

Android device.

• This se tting is not available when [BLUETOOTH]

is selected in [PHONE CONNECT].

P. AP P AU T O O N

[ON], [OFF]

Select [ON] to automatically launch Pioneer ARC

APP when an Android devic e is connecte d to the

unit via AOA. (Not available when [MEMORY] is

selected in [ANDROID WIRED].)

USB AUTO

[ON], [OFF] Select [ON] to automatically switch to [USB]

source when a USB device/iPod is connected to

the unit.

Select [OFF] when a USB device/iPod is being

connected to the unit just for charging.

ILLUMINATION settings

Menu Item Description

COLOR

[KEY COLOR], [DISP COLOR],

[BOTH COLOR]

Select color for the keys/display of the unit from

12 preset colors, [SCAN] or [CUSTOM]*.

• [SCAN]: Cycle through a variety of colors

automatica lly.

• [CUSTOM]*:

1 Press and hold the M.C. dial until the color

setting display appears.

2 Set the primary color (R (red)/G (green)/B

(blue)) and brightness level ([0] to [60]).

You cannot select a level below 10 for all three

of R (red), G (green), B (blue) at the same time.

You can also customize the preset colors. Select

one of the preset colors, then press and hold the

M.C. dial until the color setting display appears.

* The CUSTOM setting is only available for [KEY

COLOR] and [DISP COLOR].

DIM SETTING

[SYNC ILLUMI], [SYNC CLOCK],

[ON], [OFF]

Change the display brightness.

Menu Item Description

22En

BRIGHTNESS

[1] to [10] Change the display brightness.

The available setting ranges differ depending on

[DIM SETTING].

PHONE COLOR

[FLASHING] Select the key color when a call is received.

Applies the color set by [KEY COLOR].

[FLASH FX1] to [FLASH FX6] Cycle through a variety of colors automatically.

[OFF] No change in key color made.

ILLUMI FX

[ON], [OFF] The illumination effect can be seen when:

– there is an incoming call

– you are on a phone call

– a CD is inserted/ejected

The illumination effect will activate when the

ACC power is turned on/off regardless of this

setting.

MIXTRAX settings

Menu Item Description

SHORT PLAYBCK

[1.0 MIN], [1.5 MIN], [2.0 MIN],

[2.5 MIN], [3.0 MIN], [OFF]

Select the length of the playback time.

FLASH AREA

[KEY/DISPLAY], [KEY], [OFF] Select the area for the illumination effect.

When [OFF] is selec ted, the color set under the

ILLUMINATION settings (page 21) is used as the

display color.

Menu Item Description

FLASH PATTERN

[SOUND LEVEL 1] to [SOUND LEVEL

6]

Change the illumination effect according to

the sound and bass level.

The flash pattern changes according to the

sound level.

[LOW PASS 1] to [LOW PASS 6] The flash pattern changes according to the

bass level.

[RANDOM1] The flash pattern changes randomly accordi ng

to the sound level mode and low pass mode.

[RANDOM2] The flash pattern changes randomly accordi ng

to the sound level mode.

[RANDOM3] The flash pattern changes randomly accordi ng

to the low pass mode.

DISPLAY FX

[ON], [OFF] Set the MIXTRAX special effects on/off.

CUT IN FX

[ON], [OFF] Turn the MIXTRAX sound effects on/off while

manually changing the tracks.

Menu Item Description

23En

English

In the following, "NW" represents network

mode and "STD" represents standard

mode. According to the connections you

have established, change the speaker

mode to standard mode (STD) or network

mode (NW) (page 5).

WARNIN G

• When speaker output is used by 4

channels, use speakers over 50 W

(maximum input power) and between 4

Ω to 8 Ω (impedance value). Do not use 1

Ω to 3 Ω speakers for this unit.

• When rear speaker output is used by 2 Ω

of subwoofer, use speakers over 70 W

(maximum input power).

* Please refer to connections for a

connection method.

• The black cable is ground. When

installing this unit or power amp (sold

separately), make sure to connect the

ground wire first. Ensure that the ground

wire is properly connected to metal parts

of the car’s body. The ground wire of the

power amp and the one of this unit or

any other device must be connected to

the car separately with di fferent screws. If

the screw for the ground wire loosens or

falls out, it could result in fire, generation

of smoke or malfunction.

Important

• When installing this unit in a vehicle

without an ACC (accessory) position on

the ignition switch, failure to connect the

red cable to the terminal that detects

operation of the ignition key may result

in battery drain.

• Use this unit with a 12-volt battery and

negative grounding only. Failure to do so

may result in a fire or malfunction.

• To prevent a short-circuit, overheating or

malfunction, be sure to follow the

direction s below.

– Disconnect the negative terminal of the

battery before installation.

– Secure the wiring with cable clamps or

adhesive tape. Wrap adhesive tape

around wiring that comes into contact

with metal parts to protect the wiring.

– Place all cables away from moving par ts,

such as the shift lever and seat rails.

– Place all cables away from hot places,

such as near the heater outlet.

Connections/Installation

Connections

Ground wire POWER AMP

Other devices

(Another electronic

device in the car)

Metal parts o f

car’s body

*1 Not supplied for this unit

ACC posi tion No ACC p osition

– Do not connect the yellow cable to the

battery by passing it through the hole

to the engine compartment.

– Cover any disconnected cable

connectors with insulating tape.

– Do not shorten any cables.

– Never cut the insulation of the power

cable of this unit in order to share the

power with other devices. The current

capacity of the cable is limited.

– Use a fuse of the rating prescribed.

– Never wire the negative speaker cable

directly to ground.

– Never band together negative cables of

multiple speakers.

• When this unit is on, control signals are

sent through the blue/white cable.

Connect this cable to the system remote

control of an external power amp or the

vehicle’s auto-antenna relay control

terminal (max. 300mA 12 V DC). If the

vehicle is equipped with a glass antenna,

connect it to the antenna booster power

supply terminal.

• Never connect the blue/white cable to

the power terminal of an external power

amp. Also, never connect it to the power

terminal of the auto antenna. Doing so

may result in battery drain or a

malfunction.

• The graphical symbol placed on

the product means direc t current.

This unit

Microphone 3 m (9 ft. 10-1/8 in.)

SiriusXM Connect Vehicle Tuner input

(Only for FH-X830BHS/X730BS)

Power cord input

Microphone input

Rear output (STD) or middle range

output (NW)

Front output (STD) or high range output

(NW)

Antenna input

Fuse (10 A)

Wired remote input

Hard-wired remote control adapter c an

be connected (sold separately).

Subwoofer output

SiriusXM Connect Vehicle Tuner (sold

separately)

Power cord

Perform these connections when not

connecting a rear speaker or middle range

speaker lead to a subwoofer.

24En

Perform these connections when using a

subwoofer without the optional amplifier.

Important

In the case of above, two 4 Ω

subwoofers wired in parallel will represent

a 2 Ω load.

To power cord input

Left

Right

Front speaker (STD) or high range

speaker (NW)

Rear speaker (STD) or middle range

speaker (NW)

White

White/black

Gray

Gray/black

Green

Green/black

Viole t

Viole t/black

Black (chassis ground)

Connect to a clean, paint-free metal

location.

Yel l ow

Connect to the constant 12 V supply

terminal.

Red

Connect to terminal controlled by the

ignition switch (12 V DC).

Blue/white

Connect to th e system control terminal

of the power amp or auto-antenna relay

control terminal (max. 300 mA 12 V DC).

Subwoofer (4 Ω)

When using a subwoofer of 2 Ω, be sure

to connect the subwoofer to the violet

and violet/black leads of this unit. Do

not connect anything to the green and

green/black leads.

Not used.

Subwoofer (4 Ω) × 2

Orange/white

Connect to a car’s illumination signal.

Power amp (sold separately)

Perform these connections when usi ng the

optional amplifier.

System remote control

Connect to blue/white cable.

Power amp (sold separately)

Connect with RCA cables (sold

separately)

To rear output (STD) or middle range

output (NW)

Rear speaker (STD) or middle range

speaker (NW)

To front output (STD) or high range

output (NW)

Front speaker (STD) or high range

speaker (NW)

To subwoofer output

Subwoofer

Important

• C heck all connections and systems before

final installation.

• Do not use unauthorized parts as this

may cause malfunctions.

• Cons ult your dealer if installation requires

drilling of holes or other modifications to

the vehicle.

• Do not install this unit where:

– it may interfere with operation of the

vehicle .

– it may cause injury to a passenger as a

result of a sudden stop.

• T he semiconductor laser will be damaged

if it overheats. Install this unit away from

hot places such as near the heater outlet.

• Optimum performance is

obtained when the unit is

installed at an angle of less

than 60°.

• When installing, to ensure proper heat

dispersal when using t his unit, make sure

you leave ample space behind the rear

panel and wrap any loose cables so they

are not blocking the vents.

1 Determine the appropriate position

where the holes on the bracket and

the side of the unit match.

2 Tighten the screws on each side.

Tap pin g sc rew (5 m m × 9 mm, no t

supplied with product)

Mounting bracket

Dashboard or console

The microphone should be placed directly

in front of the driver at a suitable distance

to pick up their voice clearly.

CAUTION

It is extremely dangerous to allow the

microphone lead to become wound

around the steering column or shift lever.

Be sure to install the microphone in such a

way that it will not obstruct driving. It is

Installation

Installing the microphone

Leave ample

space

5 cm

5 cm

25En

English

recommended to use the clamps (sold

separately) to arrange the le ad.

NOTE

Depending on the vehicle model, the

microphone cable length may be too short

when you mount the microphone on the

sun visor. In such cases, install the

microphone on the steering column.

To install on the sun visor

1 Fit the microphone lead into the

groove.

2 Install the microphone clip on the sun

visor.

Lowering the sun visor reduces the

voice recognition rate.

To install on the steering

column

1 Slide the microphone base to detach it

from the microphone clip.

Microphone

Microphone clip

Microphone base

2 Install the microphone on the rear side

of the steering column.

Microphone

lead

Groove

Microphone clip

Double-sided tape

The display automaticall y returns to the

normal display.

→ No operations have been made for

about 30 seconds.

– Perform an operation.

The repeat play range changes

unexpectedly.

→ Depending on the repeat play range,

the selected range may change when

another folder or track is being selected

or during fast forwarding/reversing.

– Select the repeat play range again.

A subfolder is not played back.

→ Subfolders cannot be played when

[FLD] (folder repeat) is selected.

– Select another repeat play range.

The sound is intermittent.

→ You are using a device, such as a cellular

phone, that may cause audible

interference.

– Move electrical devices that may be

causing the interference away from

the unit.

The sound from the Bluetooth audio

source is not played back.

→ There is a call in progress on a

Bluetooth-connected cellular phone.

– The sound will be played back when

the call is terminated.

→ A Bluetooth-connected cellular phone

is currently being operated.

– Stop using the cellular phone.

→ The connection between the unit and

the cellular phone is not established

correctly after a call made by a

Bluetooth-connected cellular phone.

– Make a Bluetooth connection

between the unit and the cellular

phone again.

Common

AMP ERROR

→ This unit fails to operate or the speaker

connection is incorrect.

→ The protective circuit is activated.

– Check the speaker connection.

– Turn the ignition switch OFF and back

to ON again. If the message remains,

contact your dealer or an authorized

Pioneer Service Station for assistance.

NO XXXX (NO TITLE, for example)

→ There is no embedded text information.

– Switch the display or play another

track/file.

CD player

ERROR-07, 11, 12, 17, 30

→ The disc is dirty.

–Clean the disc.

→ The disc is scratched.

–Replace the disc.

ERROR-07, 10, 11, 12, 15, 17, 30, A0

→ There is an electrical or mechanical

error.

– Turn the ignition switch OFF and back

to ON, then back to the CD player.

ERROR-15

→ The inser ted disc is blank.

–Replace the disc.

ERROR-23

→ Unsupported CD format.

–Replace the disc.

Additional Information

Troubleshooting

Error messages

26En

FORMAT READ

→ Someti mes there is a delay between the

start of playback and when you start to

hear any sound.

– Wait until the message disappear s and

you hear sound.

NO AUDIO

→ The inserted disc does not contain any

playable files.

– Replace the disc.

SKIPPED

→ The inserted disc contains DRM

protected files.

– The protected files are skipped.

PROTECT

→ All the files on the inserted disc are

embedded with DRM.

– Replace the disc.

USB device/iPod

FORMAT READ

→ Someti mes there is a delay between the

start of playback and when you start to

hear any sound.

– Wait until the message disappear s and

you hear sound.

NO AUDIO

→ There are no songs.

– Transfer the audio files to the USB

device and connect.

→ The connected USB device has security

enabled.

– Follow the USB device instructions to

disable the security.

SKIPPED

→ The connected USB device contains

DRM protected files.

– The protected files are skipped.

PROTECT

→ All the files on the connected USB

device are embedded with DRM.

– Replace the USB device.

N/A USB

→ The connected USB device is not

supported by this unit.

– Disconnect your device and replace it

with a compatible USB device.

HUB ERROR

→ The USB device connected via a USB

hub is not supported by this unit.

– Connect the USB device direc tly to this

unit using a USB cable.

CHECK USB

→ The USB connector or USB cable has

short-circuited.

– Check that the USB connector or USB

cable is not caught in something or

damaged.

→ The connected USB device consumes

more than maximum allowable current.

– Disconnect the USB device and do not

use it. Turn the ignition switch OFF

and back to ACC or ON. Connect only

compliant USB devices.

→ The iPod operates correctly but does

not charge.

– Make sure the connection cable for

the iPod has not shorted out (e.g., not

caught in metal objects). After

checking, turn the ignition switch OFF

and back to ON, or disconnect the

iPod and reconnect.

ERROR-19

→ Communication failed.

– Perform one of the following

operations, then return to the USB

source.

• Turn the ignition switch OFF and

back to ON.

• Disconnect the USB device.

• Change to a different source.

→ iPod failure.

– Disconnect the cable from the iPod.

Once the iPod’s main menu is

displayed, reconnect the iPod and

reset it.

ERROR-23

→ USB device was not formatted properly.

– Format the USB device with FAT12,

FAT1 6 or FAT 32.

ERROR-16

→ The iPod firmware version is old.

–Update the iPod version.

→ iPod failure.

– Disconnect the cable from the iPod.

Once the iPod’s main menu is

displayed, reconnect the iPod and

reset it.

STOP

→ There are no songs in the current list.

– Select a list that contains songs.

NOT FOUND

→ No related songs.

– Transfer songs to the iPod.

NO BT DEVICE GO TO BT MENU TO

REGISTER

→ No Bluetooth device found.

– Connect the unit and iPod via

Bluetooth (page 9).

CONN. FAILED PRESS BAND KEY TO

RETRY

→ Bluetooth connection with iPod failed.

–Press BAND/ to make a

connection again.

DISCONNECTED PRESS BAND KEY TO

RETRY

→ Bluetooth connection with iPod failed.

–Press BAND/ to make a

connection again.

Bluetooth device

ERROR-10

→ The power failed for the Bluetooth

module of the unit.

– Turn the ignition switch OFF and back

to ACC or ON.

Pandora

ERROR-19

→ Communication failed.

– Disconnect the cable from the device.

Once the device’s main menu is

displayed, reconnect the device and

reset it.

START UP APP

→ The Pandora application has not started

running yet.

– Start up the Pandora application.

RATING ERROR

→ The thumb rating operation was

disabled.

– Run the same command for another

track.

CAN'T SKIP

→ The skip operation was disabled.

– Run the same command for another

track.

TRY LATER

→ Unable to save thumb rating.

→ Unable to save BookMark.

→ Unable to add station.

– Try again later.

MAINTENANCE

→ Pandora system is undergoing

maintenance.

– Try again later.

SKIP LIMIT

→ Due to music licen sing restrictions,

Pandora limit s the total number of ski ps

per hour.

– Wait until Pandora allows you to skip

again.

27En

English

UPDATE APP

→ This version of the Pandora application

is not supporte d.

– Connect a device that has a

compatible version of the Pandora

application installed.

LOGIN ERROR

→ Your Pandora account is not logged in.

– Disconnect the cable from the device,

and log in to your Pandora account.

Then reconnect the device.

CHECK DEVICE

→ Device error message displayed in the

Pandora application.

– Check the connected device.

PLEASE CREATE A STATION ON THE

PHONE

→ No station found.

– Create a station in the Pandora

application on your connected device.

SELECT STN

→ No station selected.

– Select a station.

NO BT DEVICE GO TO BT MENU TO

REGISTER

→ No Bluetooth device found.

– Connect the unit and the device via

Bluetooth (page 9).

CONN. FAILED PRESS BAND KEY TO

RETRY

→ Bluetooth connection failed.

– Press BAND/ to make a

connection again.

CHECK APP PRESS BAND KEY TO RETRY

→ Connection to the Pandora application

failed.

– Press BAND/ to make a

connection again.

DISCONNECTED PRESS BAND KEY TO

RETRY

→ Bluetooth connection lost.

– Press BAND/ to make a

connec tion again .

STATION FULL

→ A new station cannot be added.

– Delete an old station to open a spot

for a new one.

CAN.T DELETE

→ The station could not be deleted.

– Run the same command for another

station.

NO NETWORK

→ The connected device is out of area.

– Connect the device to a network.

NO SERVICE IN THIS COUNTRY

→ The connected device is out of area.

– Connect the device to a network.

STN DELETED

→ The operation was disabled.

– Run the same command for another

station.

Apps

NO BT DEVICE GO TO BT MENU TO

REGISTER

→ No Bl uetooth device found.

– Connect the unit and the device via

Bluetooth (page 9).

CONN. FAILED PRESS BAND KEY TO

RETRY

→ Bluetooth connection failed.

– Press BAND/ to make a

connec tion again .

DISCONNECTED PRESS BAND KEY TO

RETRY

→ Bluetooth connection failed.

– Press BAND/ to make a

connec tion again .

CHECK APP

→ Connection to the application failed.

– Follow the instructions that appear on

the screen.

START UP APP

→ The application h as not started running

yet.

– Operate the mobile device to start up

the application.

Spotify

NO BT DEVICE GO TO BT MENU TO

REGISTER

→ No Bluetooth device found.

– Connect the unit and the device via

Bluetooth (page 9).

CONN. FAILED PRESS BAND KEY TO

RETRY

→ Bluetooth connection failed.

– Press BAND/ to make a

connection again.

CHECK APP PRESS BAND KEY TO RETRY

→ Connection to the Spotify application

failed.

– Press BAND/ to make a

connection again.

DISCONNECTED PRESS BAND KEY TO

RETRY

→ Bluetooth connection lost.

– Press BAND/ to make a

connection again.

CHECK APP

→ Connection to the Spotify application

failed.

– Follow the instructions that appear on

the screen.

SiriusXM Satellite Radio (Only

for FH-X830BHS/X730BS)

CHECK ANTENNA

→ The antenna cable may be either

disconnected or damaged.

– Check the antenna connection or

replace if damag ed.

CHECK TUNER

→ The radio is having difficulty

communicating with the SiriusXM

Connect Vehicle Tuner. The tuner may

be disconne cted or damaged.

– Verify that the SiriusXM Connect

Vehicle Tuner cable is securely

connected to the radio.

NO SIGNAL

→ The SiriusXM Connect Vehicle Tuner is

having difficulty receiving the SiriusXM

satellite signal.

– Move your vehicle outdoors with a

clear view of the southern sky.

– Make sure that the SiriusXM magnetic

mount antenna is mounted on a metal

surface on the outside the vehicle.

– Move the SiriusXM antenna away from

any obstructions.

SUBSCRIPTIO N UPDATED

→ This unit has detected a change in your

SiriusXM subscription status.

– Press any key to clear the message.

CH UNAVAIL

→ The channel that you have requested is

not available.

– Check the SiriusXM channel lineup.

CHAN UNSUB

→ The channel that you have requested is

not included in your SiriusXM

subscription package.

– Check the content of your SiriusXM

subscription package.

28En

CH LOCKED

→ The channel has been locked by the

Parental Control function.

– Set [LOCKED CH] to [OFF] or [CLEAR

ALL] to [YES] in the FUNCTION settings

(page 19).

NO TUNEMIX CH

→ There is only one music in the band.

– Select a band with two or more

channels.

– Add more music channels to the

current band.

Discs and player

• Use only discs that feature either of the

following two logos.

• Use 12-cm discs.

• Use only conventional, fully circular discs.

• The following types of discs cannot be

used with this unit:

–DualDiscs

– 8-cm discs: Attempts to use such discs

with an adaptor may cause the unit to

malfunction.

– Oddly shaped discs

–Discs other than CDs

– Damaged discs, including discs that are

cracked, chipped or warped

– CD-R/RW discs that have not been

finalized

• D o not write on or apply chemicals to the

surface of the discs.

• To clean a CD, wipe the disc with a soft

cloth outward from the center.

• Condensation may temporarily impair

the player’s performance. Let it rest for

about one hour to adjust to a warmer

temperature. Also, wipe any damp discs

off with a soft cloth.

• When using discs that can be printed on

label surfaces, check the instruc tions and

the warnings of the discs. Depending on

the discs, inserting and ejecting may not

be possible. Using such discs may result

in damage to this equipment.

• Do not attach commercially available

labels or other materials to the discs.

– The discs may warp making the disc

unplayable.

– The labels may come off during

playback and prevent ejection of the

discs, which may result in damage to

the equipment.

USB storage device

• Connections via USB hubs are not

supported.

• Firmly secure the USB storage device

before driving. Do not let the USB storage

device fall onto the floor, where it may

become jammed under the brake or

accelerator pedal.

• Depending on the USB storage device,

the following problems may occur.

–Operations may vary.

–The storage device may not be

recognized.

– Files may not be played back properly.

– The device may cause audible

interference when you are listening to

the radio.

iPod

• Do not leave the iPod in places with high

temperatures.

• Firmly secure the iPod when driving. Do

not let the iPod fall onto the floor, where

it may become jammed under the brake

or accelerator pedal.

• The settings of the iPod such as the

equalizer and repeat play are changed

automatically when the iPod is

connected to the unit. Once the iPod is

Handling guidelines

disconnected, those settings will return

to the original settings.

• I ncompatible text saved on the iPod will

not be displayed by the unit.

• Only the first 32 characters can be

displayed as a file name (including the file

extension) or a folder name.

• The unit may not work properly

depending on the application used to

encode WMA files.

• There may be a slight delay at the start of

the playback of audio files embedded

with image data, or audio files stored on a

USB device with numerous folder

hierarchies.

CAUTION

• Pioneer cannot guarantee compatibility

with all USB mass storage devices, and

assumes no responsibility for any loss of

data on media players, smartphones, or

other devices while using this product.

• Do not leave discs or a USB storage

device in any place that is subject to high

temperatures.

WMA files

MP3 files

WAV files

• WAV file formats cannot be connected via

MTP.

AAC files

FLAC files

• FLAC file formats cannot be connected

via MTP.

• FLAC files may not be playable,

depending on the encoder.

Compressed audio

compatibility

File extension .wma

Bit rate 48 kbps to 320 kbps

(CBR), 48 kbps to 384

kbps (VBR)

Sampling fre quency 32 kHz, 44.1 kH z, 48

kHz

Windows Media™

Audio Profession al,

Lossless, Voice/DRM

Stream/Stream with

video

Not compatible

File extension .mp3

Bit rate 8 kbps to 320 kbps

(CBR), VBR

Sampling frequency 8 kHz to 48 kHz (32

kHz, 44.1 kHz, 48 kHz

for emphasis )

Compatible ID3 tag

versio n

1.0, 1.1, 2.2, 2.3, 2.4

(ID3 tag Version 2.x is

given priority over

Versi on 1.x .)

M3u playlist Not compatible

MP3i (MP3

interactive), mp 3 PRO

Not compatible

File ex tension .wav

Quantization bits 8 and 16 (LPCM), 4

(MSADPCM)

Sampling frequency 16 kHz to 48 kHz

(LPCM), 22.05 kHz and

44.1 kHz (MS ADPCM)

Compatible format AAC encoded by

iTunes

File extension .m4a

Sampling frequency 11.025 kHz to 48 kHz

Transmission rate 16 kbps to 320 kbps,

VBR

Apple Lossless Not compatible

AAC file bought from

the iTunes Store (.m4p

file extension)

Not compatible

29En

English

Disc

• Regardless of the length of the blank

section between the songs from the

original recording, compressed audio

discs play with a short pause between

songs.

USB device

• There may be a slight delay when starting

playback of audio files on a USB storage

device with numerous folder hierarchies.

This unit supports only the following iPod

models. Suppor ted iPod software versions are

shown below. Older versio ns may not be

supported.

Made for

– iPod touch (1st through 6th generation)

–iPod classic

– iPod with video

– iPod nano (1st through 7th generation)

–iPhone 6s

–iPhone 6s Plus

–iPhone 6

–iPhone 6 Plus

–iPhone 5s

–iPhone 5c

–iPhone 5

–iPhone 4s

–iPhone 4

–iPhone 3GS

–iPhone 3G

–iPhone

• Ope rations may vary depe nding on the

generation and/or software version of

the iPod.

• Users of iPod with the Lightning

Connector should use the Lightning to

USB Cable (supplied with iPod).

• Users of iPod with the Dock Connector

should use the CD-IU51. For details,

consult your dealer.

• Refer to the iPod manuals for information

about the file/format compatibility.

• Audiobook, Podcast: Compatible

CAUTION

Pioneer accepts no responsibility for data

lost on the iPod, even if that data is lost

while this unit is used.

The user cannot assign folder numbers and

specify playback sequences with this unit.

Sequence of audio file depends on the

connected device.

Note that the hidden files in a USB device

cannot be played back.

File extension .flac

Sampling fre quency 8/11.025/ 12/16/22.05/

24/32/44.1/48/96 kHz

Quantization bit rate 16/24 bit

Channel mode 1/2 ch

Playable folder

hierarchy

Up to eight tiers (A

practical hie rarchy is

less than two tiers.)

Playable folders Up to 99

Playable files Up to 999

File system ISO 9660 Level 1 and

2, Romeo, Joliet

Multi-session

playback

Compatible

Packet write data

transfer

Not compatible

Playable folder

hierarchy

Up to eight tiers (A

practical hie rarchy is

less than two tiers.)

Playable folders Up to 1 500

Playable files Up to 15 000

Playback of copyright-

protected files

Not compatible

Part itioned USB

device

Only the fi rst partition

can be played.

iPod compatibility

Sequence of audio files

Example of a hierarchy

Bluetooth

The Bluetooth® word mark and logos are

registered tradem arks owned by Bluetooth S IG,

Inc. and any use of such marks by PIONEER

CORPORATION is under license. Other

trademarks and trade names are those of their

respective owners.

iTunes

Apple and iTunes are trademarks of Apple

Inc., registered in the U.S. and other

countries.

WMA

Windows Media is either a registered

trademark or trademark of Microsoft

Corporation in the United States and/or

other countries.

This product includes technology owned

by Microsoft Corporation and cannot be

used or distributed without a license from

Microsoft Licensing, Inc.

FLAC

Copyright © 2000-2009 Josh Coalson

Copyright © 2011-2014 Xiph.Org

Found ation

Redistribution and use in source and

binary forms, with or without modification,

are permitted provided that the follow ing

conditions are met:

– Redistributions of source code must

retain the above copyright no tice, this list

of conditions and the following

disclaimer.

– Redistributions in binary form must

reproduce the above copyright notice,

this list of conditions and the following

disclaimer in the documentation and/or

other materials provided with the

distribution.

– Neither the name of the Xiph.org

Foundation nor the names of its

contributors may be used to endorse or

promote products derived from this

software without specific prior written

permission.

THIS SOFTWARE IS PROVIDED BY THE

COPYRIGHT HOLDERS AND

CONTRIBUTORS “AS IS” AND ANY EXPRESS

OR IMPLIED WARRANTIES, IN CLUDING, BUT

NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE ARE

DISCLAIMED. IN NO EVENT SHALL THE

FOUNDATION OR CONTRIBUTORS BE

LIABLE FOR ANY DIRECT, INDIRECT,

INCIDENTAL, SPECIAL, EXEMPLARY, OR

CONSEQUENTIAL DAMAGES (INCLUDING,

BUT NOT LIMITED TO, PROCUREMENT OF

SUBSTITUTE GOODS OR SERVICES; LOSS OF

USE, DATA, OR PROFITS; OR BUSINESS

INTERRUPTION) HOWEVER CAUSED AND

ON ANY THEORY OF LIABILITY, WHETHER

IN CONTRACT, STRICT LIABILITY, OR TORT

(INCLUDING NEGLIGENCE OR OTHERWISE)

ARISING IN ANY WAY OUT OF THE USE OF

THIS SOFTWARE, EVEN IF ADVISED OF THE

POSSIBILITY OF SUCH DAMAGE.

iPod & iPhone

iPhone, iPod, iPod classic, iPod nan o, and

iPod touch are trademarks of Apple Inc.,

registered in the U.S. and other countries.

Lightning is a trademark of Apple Inc.

Copyright and trademark

Folder

Compressed

audio file

to : Playback sequence

01 to 05: Folde r number

30En

“Made for iPod” and “Made for iPhone”

mean that an electronic accessory has

been designed to connect specifically to

iPod or iPhone, respectively, and has been

certified by the developer to meet Apple

performance standards. Apple is not

responsible for the operation of this device

or its compliance with safety and

regulatory standards. Please note that the

use of this accessory with iPod or iPhone

may affect wireless performance.

Android & Google Play

Android, Google Play, and the Google Play

logo are trademarks of Google Inc.

SiriusXM Satellite Radio

Sirius, XM and all related marks and logos

are trademarks of Sirius XM Radio Inc. All

rights reserved.

Pandora® interne t radio

PANDORA, the PANDORA logo, and the

Pandora trade dress are trademarks or

registered trademarks of Pandora Media,

Inc. Used with permission.

Pandora is only available in certain

countries. Please visit

http://www.pandora.com/legal

for more information.

MIXTRAX

MIXTRAX is a trademark of the PIONEER

CORPO RATION.

HD Radio™ Technology

HD Radio Technology manufactured under

license from iBiquity Digital Corporation.

U.S. and Foreign Patents. HD Radio™ and

the HD, HD Radio, and “Arc” logos are

proprietary trademarks of iBiquity Digital

Corp.

Spotify®

SPOTIFY and the Spotify logo are among

the registered trademarks of Spotify AB.

Compatible mobile digital devices and

premium subscription required, where

available, see http://pioneer.eu/spotify.

T-K ernel 2. 0

This product uses the source code of T-

Kernel 2.0 under T-License 2.0 granted by

T-Engine Forum (www.tron.org).

MP3

Copyright (C) 1998-2009 PacketVideo

Licensed under the Apache License,

Version 2.0 (the "License"); you may not use

this file except in compliance with the

License.

You may obtain a copy of the License at

http://www.apache.org/licenses/LICENSE-

2.0

Unless required by applicable law or

agreed to in writing, software distributed

under the License is distributed on an "AS

IS" BASIS, WITHOUT WARRANTIES OR

CONDITIONS OF ANY KIND, either express

or implied.

See the License for the specific language

governing permissions and limitations

under the License.

General

Power source: 14.4 V DC (10.8 V to 15.1 V

allowable)

Grounding system: Negative type

Maximum current consumption: 10.0 A

Dimensions (W × H × D):

D

Chassis: 178 mm × 100 mm × 165 mm

(7 in. × 3-7/8 in. × 6-1/2 in.)

Nose: 170 mm × 96 mm × 16 mm (6-

3/4 in. × 3-3/4 in. × 5/8 in.)

Specifications

Weight: 1.3 kg (2.9 lbs)

Audio

Maximum power output:

• 50 W × 4 ch/4 Ω (for no subwoofer)

• 50 W × 2 ch/4 Ω + 70 W × 1 ch/2 Ω

(for subwoofer)

Continuous power output:

22 W × 4 (50 Hz to 15 000 Hz, 5 %

THD, 4 Ω load, both channels driven)

Load impedance: 4 Ω (4 Ω to 8 Ω (2 Ω for 1

ch) allowable)

Preout maximum output level: 2.0 V

Equalizer (13-Band Graphic Equalizer):

Frequency: 50 Hz/80 Hz/125 Hz/200

Hz/315 Hz/500 Hz/800 Hz/1.25 kHz/2

kHz/3.15 kHz/5 kHz/8 kHz/12.5 kHz

Gain: ±12 dB (2 dB step)

High pass filter (Standard mode):

Frequency: 50 Hz/63 Hz/80 Hz/100

Hz/125 Hz/160 Hz/200 Hz

Slope: -6 dB/oct, -12 dB/oct, -18 dB/

oct, -24 dB/oct, OFF

Subwoofer/Low pass filter (Standard

mode):

Frequency: 50 Hz/63 Hz/80 Hz/100

Hz/125 Hz/160 Hz/200 Hz

Slope: -6 dB/oct, -12 dB/oct, -18 dB/

oct, -24 dB/oct, OFF

Gain: +10 dB to –24 dB (1 dB step)

Phase: Normal/Reverse

Speaker level (Standard mode):

+10 dB to –24 dB (1 dB step)

Time alignment (Standard mode):

0 Inch to 140 Inch (1 inch/Step)

Bass boost (Standard mode):

Gain: +12 dB to 0 dB

High pass filter (HIGH) (Network mode):

Frequency: 1.25 kHz/1.6 kHz/2 kHz/

2.5 kHz/3.15 kHz/4 kHz/5 kHz/6.3 kHz/

8 kHz/10 kHz/12.5 kHz

Slope: -6 dB/oct, -12 dB/oct, -18 dB/

oct, -24 dB/oct

High pass filter (MID) (Network mode):

Frequency: 25 Hz/31.5 Hz/40 Hz/50

Hz/63 Hz/80 Hz/100 Hz/125 Hz/160

Hz/200 Hz/250 Hz

Slope: -6 dB/oct, -12 dB/oct, -18 dB/

oct, -24 dB/oct, OFF

Low pass filter (MID) (Network mode):

Frequency: 1.25 kHz/1.6 kHz/2 kHz/

2.5 kHz/3.15 kHz/4 kHz/5 kHz/6.3 kHz/

8 kHz/10 kHz/12.5 kHz

Slope: -6 dB/oct, -12 dB/oct, -18 dB/

oct, -24 dB/oct, OFF

Subwoofer (Network mode):

Frequency: 25 Hz/31.5 Hz/40 Hz/50

Hz/63 Hz/80 Hz/100 Hz/125 Hz/160

Hz/200 Hz/250 Hz

Slope: -12 dB/oct, -18 dB/oct, -24 dB/

oct, -30 dB/oct, -36 dB/oct, OFF

Gain: +10 dB to –24 dB (1 dB step)

Phase: Normal/Reverse

Speaker level (Network mode):

+10 dB to –24 dB (1 dB step)

Time alignment (Network mode):

0 Inch to 140 Inch (1 inch/Step)

Bass boost (Network mode):

Gain: +12 dB to 0 dB

CD player

System: Compact disc audio system

Usable discs: Compact disc

Signal-to-noise ratio: 94 dB (1 kHz) (IEC-A

network)

Number of channels: 2 (stereo)

MP3 decoding format: MPEG-1 & 2 Audio

Layer 3

WMA decoding format: Ver. 7, 7.1, 8, 9, 10,

11 (2 ch audio) (Windows Media

Player)

AAC decoding format: MPEG-4 AAC (iTunes

encoded only) (Ver. 10.6 and earlier)

WAV signal format: Linear PCM & MS

ADPCM (Non-compressed)

USB

USB standard specification: USB 2.0 full

speed

Maximum current supply: 1 A